Model No. IMBE39401
Serial No.
USER’S MANUAL
Write the serial number in the
space above for reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Patent Pending
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Precautions
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the weight rack.
1. Read all instructions in this manual before
using the weight rack. Use the weight rack
only as described in this manual.
10. Always set both weight rests and both safety
spotters at the same height.
11. The weight bench is designed to support a
maximum of 550 pounds, including the user,
a barbell, and weights (not included). Do not
place more than 300 pounds, including the
barbell, on the weight rests. Do not place
more than 150 pounds on the weight carriage
or the leg lever.
2. It is the responsibility of the owner to ensure
that all users of the weight rack are ade-
quately informed of all precautions.
3. The weight rack is intended for home use
only. Do not use the weight rack in any com-
mercial, rental, or institutional setting.
12. Make sure that the cables remain on the pul-
leys at all times. If the cables bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys.
4. Use the weight rack only on a level surface.
Cover the floor beneath the weight rack to
protect the floor or carpet.
5. Inspect and tighten all parts each time you
use the weight rack. Replace any worn parts
immediately.
13. Always wear athletic shoes for foot protec-
tion while exercising.
14. Always exercise with a partner. When you
are performing squat exercises, your partner
should stand behind you to catch the barbell
if you cannot complete a repetition.
6. Keep children under 12 and pets away from
the weight rack at all times.
7. Keep hands and feet away from moving parts.
15. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
8. Always secure weights (not included) with
the weight clips when they are mounted on
the weight carriage.
16. Always disconnect the lat bar from the
weight rack when performing an exercise
that does not require the lat bar.
9. Always make sure there is an equal amount
of weight on each end of the barbell (not
included).
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Thank you for selecting the versatile IMAGE® 5.5
weight rack. The IMAGE® 5.5 is designed to help you
develop every major muscle group of the body.
Whether your goal is a shapely figure, dramatic
increase in muscle size and strength, or a healthier
cardiovascular system, the IMAGE® 5.5 will help you
achieve the specific results you want.
toll-free at 1-800-999-3756, Monday through Friday, 6
a.m. until 6 p.m. Mountain Time (excluding holidays).
To help us assist you, please note the product model
number and serial number before calling. The model
number is IMBE39401. The serial number can be
found on a decal attached to the weight rack (see the
front cover of this manual).
For your benefit, read this manual carefully before
using the weight rack. If you have additional ques-
tions, please call our Customer Service Department
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
High Pulley Station
Chin-up Bar
Lat Bar
Right Side
Left Side
Weight Rest
Weight
Carriage
Safety Spotter
Leg Lever
Weight Tube
Low Pulley
Station
Weight Tube
Seat
Note: The terms “right side” and “left side” are determined
Backrest
relative to a person using the rack; they do not correspond
to right and left on the drawings in the manual.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Identification Chart—Model No. IMBE39401
M6 x 16mm Screw (50)
51mm Spacer (39)
M6 x 35mm Bolt (78)
28mm Spacer (40)
M10 x 45mm Bolt (32)
M10 x 50mm Bolt (86)
24mm Spacer (38)
M6 x 52mm Screw (51)
18mm Spacer (85)
M10 x 58mm Carriage Bolt (57)
M10 Washer (37)
M10 x 66mm Bolt (35)
M8 Washer (36)
M10 x 68.5mm Bolt (75)
M8 x 72mm Bolt (33)
M6 Washer (74)
M10 x 72mm Bolt (34)
M10 Nylon Locknut (29)
M10 x 78mm Bolt (31)
M8 Nylon Locknut (30)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
• As you assemble the weight rack, make sure all
parts are oriented as shown in the drawings.
Make Things Easier for Yourself!
Everything in this manual is designed to ensure
that the weight rack can be assembled success-
fully by anyone. However, it is important to real-
ize that the versatile weight rack has many parts
and that the assembly process will take time.
Most people find that by setting aside plenty of
time, assembly will go smoothly.
• For help identifying small parts, use the Part
Identification Chart on page 5.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet
Before beginning assembly, carefully read the
following information and instructions:
• One standard screwdriver
• One Phillips screwdriver
• Assembly requires two people.
• Lubricant, such as grease or petroleum jelly,
and soapy water.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
1. Press 60mm Square Outer Caps (27) onto the ends
of the Right and Left Bases (1, 3).
1
27
29
Attach the Right and Left Bases (1, 3) to the Center
Base (2) using four M10 x 78mm Bolts (31) and
four M10 Nylon Locknuts (29). Do not tighten the
Nylon Locknuts yet.
2
31
27
29
1
27
31
27
29
3
2. Identify the two Rear Uprights (8), which are slightly
shorter than the Front Uprights (not shown).
2
Adjustment
Holes
Attach the Rear Uprights (8) to the Left and Right
Bases (1, 3) using four M10 x 78mm Bolts (31) and
four M10 Nylon Locknuts (29). Do not tighten the
Nylon Locknuts yet. Make sure the Uprights are
oriented exactly as shown, with the adjustment
holes on the indicated side near the bottom.
8
8
27
31
1
4
29
2
Press a 60mm Square Outer Cap (27) onto the end
of the Weight Guide Base (4).
29
Orient the Foot Plate (5) and the Weight Guide Base
(4) as shown. Attach the Foot Plate and the Weight
Guide Base to the Center Base (2) using two M10 x
78mm Bolts (31) and two M10 Nylon Locknuts (29).
Do not tighten the Nylon Locknuts yet.
31
5
3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Tap a 60mm Square Inner Cap (28) into the top of
each of the Front Uprights (7).
3
28
7
8
Attach one of the Front Uprights (7) and two Rack
Joint Plates (6) to the Left Base (3) using four M10
x 78mm Bolts (31) and four M10 Nylon Locknuts
(29). Make sure the Front Upright is oriented so
that the holes on the bottom of the Front
Upright and the holes in the Joint Plates line up.
If they do not line up, turn the Front Upright
upside-down. Do not tighten the Nylon
Locknuts yet. Make sure the Front Upright is
turned so the adjustment holes are facing the
Rear Upright (8).
Adjustment
Holes
1
31
29
Attach the other Front Upright (7, not shown) and
two Rack Joint Plates (6, not shown) to the Right
Base (1) in the same manner.
3
6
29
6
4. This step will require two people.
4a
4b
21
Refer to drawing 4a. Have one person hold out the
Adjustment Knobs (22) on a Safety Spotter (20),
while the other person slides the Safety Spotter
down over the right Uprights (7, 8), as shown. Hold
the Adjustment Knob out on the Weight Rest (19),
and slide the Weight Rest onto the Front Upright
(7). To avoid breaking the Square Bushings (21)
inside the top and bottom of the Safety Spotter
and Weight Rest, be careful not to catch the
Square Bushings on the edges of the Uprights
as they slide on.
7
19
8
21
22
19
20
22
21
20
22
Refer to drawing 4b. Secure the Safety Spotter (20)
and the Weight Rest (19) to the right Uprights (7, 8)
by snapping the three Adjustment Knobs (22) into
adjustment holes in the Uprights and turning them
clockwise until tight.
8
7
Assemble the other Safety Spotter (20) and Weight
Rest (19) to the left Uprights (7, 8) in the same
manner. Make sure both Safety Spotters and
both Weight Rests are at the same height.
5
6
29
5. Attach the Chin-up Bar (13) and two Rack Joint
Plates (6) to the Front Uprights (7) using four M10 x
78mm Bolts (31) and four M10 Nylon Locknuts (29).
Do not tighten the Nylon Locknuts yet.
13
31
6
31
7
7
29
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Press a 60mm Square Inner Cap (28) into the Left
Frame (12). Attach the Left Frame to the left
Uprights (7, 8) using four M10 x 78mm Bolts (31)
and four M10 Nylon Locknuts (29). Do not tighten
the Nylon Locknuts yet.
6
11
29
10
29
28
Assemble the Right Frame (10) on the right
Uprights (7, 8) in the same manner.
31
8
31
12
Attach the Center Frame (11) to the Left Frame (12)
and the Right Frame (10) using four M10 x 78mm
Bolts (31) and four M10 Nylon Locknuts (29).
Tighten all Nylon Locknuts used in steps 1–6.
29
8
31
7
31
29
7
7. Press the two 51mm Round Inner Caps (42) into
the weight tubes on the Weight Carriage (15).
7
42
15
Make sure the Weight Carriage is turned so the
weight tubes are near the top, as shown. Attach
the lower Carriage Bushing (16) to the Weight
Carriage (15) using a M10 x 66mm Bolt (35), two
M10 Washers (37), the 51mm Spacer (39), and a
M10 Nylon Locknut (29).
Weight Tube
42
29
37
16
39
37
35
8. Insert the two Weight Guides (9) into the Weight
Guide Base (4). Attach the Weight Guides using
two M8 x 72mm Bolts (33), four M8 Washers (36),
and two M8 Nylon Locknuts (30).
8
9
15
Slide the two Weight Bumpers (18) and the Weight
Carriage (15) over the Weight Guides (9). Be sure
the Weight Bumpers are on the bottom.
30
18
4
36
33
9. Press a 60mm Square Inner Cap (28) into the end
of the Weight Guide Frame (14).
36
30
9
28
36
31
14
Hold the Weight Guide Frame (14) on top of the
Center Frame (11) and the Weight Guides (9).
Attach the Weight Guides to the Weight Guide
Frame using two M8 x 72mm Bolts (33), four M8
Washers (36), and two M8 Nylon Locknuts (30).
33
11
Attach the Weight Guide Frame (14) to the Center
Frame (11) using two M10 x 78mm Bolts (31), two
M10 Washers (37), and two M10 Nylon Locknuts
(29).
9
37
29
8
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Locate the High Cable (84), which is slightly longer
than the Low Cable (not shown), and notice that
there is a ball on one end of the Cable and a metal
sleeve on the other end.
10
14
Route the metal-sleeve end of the High Cable (84)
up under the lat bar rest on the Weight Guide
Frame (14), down through the indicated hole, back
up through the next hole, and then down between
the Weight Guides (9) as shown.
9
Lat Bar
Rest
84
11. Insert the end of the High Cable (84) into the hole
in the center of the Weight Carriage (15). Attach the
Cable using a M10 x 66mm Bolt (35), two M10
Washers (37), two 24mm Spacers (38), and an M10
Nylon Locknut (29).
11
37
84
38
38
29
37
35
15
12 Lift the High Cable (84) in the location shown.
Attach two Pulleys (24) inside the bracket on the
Weight Guide Frame (14) using two M10 x 50mm
Bolts (86) and two M10 Nylon Locknuts (29).
12
24
84
14
29
86
13. Lift the High Cable (84) in the location shown.
Attach two Pulleys (24) inside the Weight Guide
Frame (14) using two M10 x 72mm Bolts (34), four
M10 Washers (37), four 18mm Spacers (85), and
two M10 Nylon Locknuts (29).
13
24
84
37
14
29
85
85
37
85
37
34
85
37
9
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Pull the High Cable (84) down in the indicated loca-
tion, so there is no slack at the ends of the Cable.
14
Locate the Low Cable (25), which has two balls on
one end. Insert the metal-sleeve end of the Cable
into the indicated hole in the Weight Guide Base
(4). Attach the Cable using an M10 x 72mm Bolt
(34), two M10 Washers (37), two 28mm Spacers
(40), and a M10 Nylon Locknut (29).
84
Route the ball-end of the Low Cable (25) through
the bracket on the Center Base (2). Attach a Pulley
(24) inside the bracket using a M10 x 45mm Bolt
(32) and a M10 Nylon Locknut (29).
25
24
37
40
4
40
29
37
34
2
32
15. Wrap the High Cable (84) around a Pulley (24) as
shown. Attach the Pulley and a Cable Trap (23) to
the two Pulley Plates (17) using a M10 x 45mm Bolt
(32) and a M10 Nylon Locknut (29).
15
84
17
24
29
23
17
Wrap the Low Cable (25) around a Pulley (24) as
shown. Attach the Pulley and a Cable Trap (23) to
the Pulley Plates (17) using a M10 x 45mm Bolt
(32) and a M10 Nylon Locknut (29).
32
Make sure the Bolts (32) are inserted through
the highest and lowest holes in the Pulley Plates
(17), and that the Cables (25, 84) are between
the Cable Traps (23) and the Pulleys (24).
23
25
16. Wet the ends of the Lat Bar (45) with a small
amount of lubricant. Slide the Handgrips (47) onto
the ends of the Lat Bar.
16
45
Make sure that all parts of the weight rack are
properly tightened. In addition, pull each cable a
few times to make sure the cables move
47
smoothly over the pulleys. If the cables do not
move smoothly, locate and correct the problem.
When weights are used, the cables may be dam-
aged if they are incorrectly routed.
47
10
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Press a 51mm x 76mm Outer Cap (56) onto each
end of the Stabilizer (58).
17
29
Attach the Stabilizer (58) to the Bench Frame (52)
with two M10 x 58mm Carriage Bolts (57) and two
M10 Nylon Locknuts (29). Attach the Stabilizer so
that the warning decal is in the position shown.
56
Decal
52
Note: Do not tighten the Nylon Locknuts yet.
58
57
56
18. Press a 50mm Square Outer Cap (65) onto each end
of the Bench Base (53).
18
Welded Nut
48
Attach the Bench Base Joint Plate (64) to the Bench
Base (53) with two M10 x 68.5mm Bolts (75), two
M10 Washers (37), and two M10 Nylon Locknuts
(29).
37
75
29
53
37
Attach the Bench Leg (48) to the Bench Base Joint
Plate (64) with two M10 x 68.5mm Bolt (75), two M10
Washers (37), and two M10 Nylon Locknuts (29). Be
sure the welded nut is in the position shown.
64
37
65
37
75
Note: Do not tighten the Nylon Locknuts yet.
65
19. Attach the Bench Leg (48) to the Bench Frame (52)
with two Bench Joint Plates (63), four M10 x 72mm
Bolts (34), and four M10 Nylon Locknuts (29).
19
34
63
52
Note: Tighten all the M10 Nylon Locknuts (29)
used in steps 17-19.
63
48
29
20. Press two 25mm x 38mm Inner Caps (72) into each
Backrest Tube (71). Press two 25mm x 38mm Inner
Caps into the Backrest Adjustment Bracket (79).
20
Lubricate
72
71
37
66
Lubricate a M10 x 192mm Bolt (66). Attach the
Backrest Tubes (71) to the welded tube on the
Backrest Adjustment Bracket (79) with the Bolt, two
M10 Washers (37) and a M10 Nylon Locknut (29).
Make sure that the Backrest Tubes are turned as
shown. The indicated holes are closer to one
side. Turn the Backrest Tubes so the holes are
closer to the floor. Do not over tighten the Nylon
Locknut; the Backrest Tubes must pivot easily.
37
Holes
29
72
79
Welded
Tube
72
11
Download from Www.Somanuals.com. All Manuals Search And Download.
21. Lubricate a M10 x 192mm Bolt (66). Attach the
Backrest Tubes (71) to the welded tube on the Bench
Frame (52) with the Bolt, two M10 Washers (37), and
a M10 Nylon Locknut (29). Note: Do not over tight-
en the Nylon Locknut; the Backrest Tubes must
pivot easily.
21
Lubricate
37
66
71
Welded Tube
52
37
29
22. Attach the Backrest (60) to the Backrest Tubes (71)
with four M6 x 52mm Screws (51) and four M6
Washers (74).
22
60
71
74
23. See the inset drawing. Press the 20mm x 40mm Inner
Cap (77) into the open end of the Seat Mounting
Bracket (67).
51
23
67
See the inset drawing. Lubricate a M10 x 68.5mm
Bolt (75). Attach the Seat Adjustment Bracket (80) to
the indicated side of the Seat Mounting Bracket (67)
with the Bolt and a M10 Nylon Locknut (29). Note: Do
not over tighten the Nylon Locknut; the Seat
Adjustment Bracket must pivot easily.
80
Lubricate
34
Lubricate
Place the Seat Mounting Bracket (67) on the Bench
Frame (52) so that the Seat Adjustment Bracket (80)
fits over the welded pin on the side of the Bench
Frame.
67
80
Welded
Pin
75
77
52
29
29
Lubricate a M10 x 72mm Bolt (34). Attach the Seat
Mounting Bracket (67) to the indicated bracket on the
Bench Frame (52) with the Bolt and a M10 Nylon
Locknut (29). Note: Do not over tighten the Nylon
Locknut; the Seat Mounting Bracket must pivot
easily.
24
59
Bracket
67
24. Turn the Seat (59) as shown. Attach the wide end of
the Seat to the bracket on the Seat Mounting Bracket
(67) with two M6 x 16mm Screws (50).
Tilt the Seat Mounting Bracket (67) upwards and
attach the narrow end of the Seat (59) to the Seat
Mounting Bracket with a M6 x 35mm Screw (78) and
an M6 Washer (74).
74
50
78
12
Download from Www.Somanuals.com. All Manuals Search And Download.
25. Attach the Adjustable Bench Leg (49) to the Bench
Leg (48) with the Small Adjustment Knob (81).
25
26
49
Insert a 45mm Square Inner Cap (26) into the top of
the Adjustable Bench Leg (49).
81
48
26. Insert three 45mm Square Inner Caps (26) into the
ends of the Leg Lever (62). Insert a 25mm Round
Inner Cap (83) into the weight tube on the Leg Lever.
Press a 25mm Angled Outer Cap (82) onto the other
end of the weight tube.
26
34
26
49
Attach the Leg Lever (62) to the Adjustable Bench
Leg (49) with an M10 x 72mm Bolt (34) and an M10
Nylon Locknut (29).
26
29
Weight
Tube
82
83
62
26
27. Insert 19mm Round Inner Caps (70) into the ends of
the three Pad Tubes (61).
27
69
70
69
49
Insert two Pad Tubes (61) through the holes in the
Leg Lever (62). Slide a Foam Pad (69) onto each
side of the Pad Tubes.
61
70
69
Insert a Pad Tube (61) through the upper tube on the
Adjustable Bench Leg (49). Slide a Foam Pad (69)
onto each side of the Pad Tube.
69
62
70
69
28. Attach the Curl Pad (54) to the Curl Upright (55) with
two M6 x 16mm Screws (50).
28
54
50
29. Make sure all parts are properly tightened before
you use the weight bench. The use of the remain-
ing parts will be explained in Adjusting the Weight
Rack, on page 14.
55
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Weight Rack
This section explains how the weight rack and bench can be adjusted. See the Exercise Guidelines on page 17 for
information about how to get the most benefit from your exercise program. See the included exercise poster for infor-
mation about how to perform a variety of exercises.
Inspect and tighten all parts each time you use the weight rack. Replace any worn parts immediately. The weight
rack can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
USING THE CURL PAD
54
To use the Curl Pad (54), unscrew the Small Adjustment
Knob (81) and lift the Leg Lever (62) out of the Bench
Leg (48). Insert the Curl Pad into the Bench Leg, and
62
secure it with the Small Adjustment Knob.
81
Note: When not using the Curl Pad (54), store it
away from the weight bench.
48
ADJUSTING THE SEAT
To raise the Seat (59), lift the narrow end of the Seat until
the appropriate tab on the Seat Adjustment Bracket (80)
engages the welded pin (not shown) on the right side of
the Bench Frame (52).
To lower the Seat (59), use the handle on the Seat
Adjustment Bracket (80) to disengage the Seat
Adjustment Bracket from the pin on the right side of the
Bench Frame (52). Lower the Seat to the desired position
and engage the appropriate tab on the Seat Adjustment
Bracket to the pin.
80
Handle
59
Pin
52
ADJUSTING THE BACKREST
60
To raise the Backrest (60), grip the end of the Backrest
with one hand and pull it upward until the Backrest
Adjustment Bracket (79) locks into the appropriate tab on
the bracket on the Bench Frame (5).
Handle
79
To lower the Backrest (60), grip the end of the Backrest
with one hand and lift it slightly. Grip the handle (not
shown) on the right side of the Backrest Adjustment
Bracket (79) with your other hand and pull the Backrest
Adjustment Bracket free of the tabs on the bracket on the
Bench Frame (52). Lower the Backrest to the desired
position and lock the Backrest Adjustment Bracket into
the desired tab on the Bench Frame bracket.
52
Bracket
WARNING: Make sure the Backrest
Adjustment Bracket (79) is securely locked to the
Bench Frame (52) before using the weight bench.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE PAD TUBES
For some exercises, it may be necessary to move the
Pad Tube (61) in the Adjustable Bench Leg (49). To do
this, remove a Foam Pad (69) from one side of the Pad
Tube. Slide the Pad Tube out of the Adjustable Bench
Leg. Reinsert the Pad Tube into the lower welded tube
on the Adjustable Bench Leg. Replace the Foam Pad
on the Pad Tube.
61
49
To do leg raise exercises, the Pad Tube (61) must be
moved to the lower welded tube, the narrow end of the
seat must be raised, and the backrest must be declined
as shown.
69
USING THE WEIGHT RESTS AND SAFETY
SPOTTERS
Adjustment
Holes
8
Before beginning an exercise, move the Weight Rests
(19) and the Safety Spotters (20) to sets of holes in the
Uprights (7, 8) that are best suited for that exercise. Do
this by turning the Adjustment Knobs (22) counterclock-
wise until loose. Pull the Knobs out and slide the
Weight Rests or the Safety Spotters to the desired
height. Snap the Knobs into the adjustment holes in the
Uprights and turn the Knobs clockwise until tight.
7
19
20
22
The selected holes for the Safety Spotters (20) should
represent the lowest point to which you want the barbell
to go during the exercise. The selected holes for the
Weight Rests (19) should be at a comfortable height for
lifting and replacing the barbell. Perform the exercise as
shown on the accompanying exercise chart. Note: Make
sure the Adjustment Knobs (22) are fully tightened.
WARNING:
Always set both Weight
Rests (19) at the same height and both Safety
Spotters (20) at the same height.
19
20
SETTING UP FOR SQUAT EXERCISES
Squat exercises should be performed inside the rack
(behind the dotted line in the picture). When performing
squat exercises, set the Weight Rests (19) and the
Safety Spotters (20) at a comfortable height in the man-
ner describe in USING THE WEIGHT RESTS AND
SAFETY SPOTTERS above.
19
20
Squat
Area
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING WEIGHTS TO THE WEIGHT CARRIAGE
Weight
Tube
To use the high or low pulley station, slide the desired
amount of weight onto the weight tubes on the Weight
Carriage (15). Secure the weights with Weight Clips (43).
Weight
Tube
WARNING:
Do not place more than
150 pounds on the Weight Carriage (15). Always
place the same amount of weight on each side of
the Weight Carriage, and secure the weights on
the Weight Carriage with the Weight Clips (43).
15
43
ATTACHING THE LAT BAR TO THE HIGH PULLEY
STATION OR THE LOW PULLEY STATION
25
To use the high pulley station or the low pulley station,
first place the desired weights on the weight carriage
(see ATTACHING WEIGHTS TO THE WEIGHT CAR-
RIAGE above). Next, attach the Lat Bar (45) to either
Cable (25) with a Cable Clip (46).
46
45
WARNING: Always disconnect the
Lat Bar (45) when performing an exercise that
does not require using the Lat Bar.
TIGHTENING THE CABLES
Woven cable, the type of cable used on the weight rack,
can stretch slightly after it is first used. If there is slack
in the cables, tighten them as described below.
17
24
29
23
17
Remove the M10 x 45mm Bolt (32) and the M10 Nylon
Locknut (29) attaching the lower Pulley (24) and Cable
Trap (23) to the two Pulley Plates (17). Reattach the
lower Pulley and Cable Trap to the higher holes in the
Pulley Plates using the Bolt and Nylon Locknut.
32
23
If moving just the lower Pulley (24) does not sufficiently
tighten the cables, you can also move the upper Pulley
down one set of holes in the Pulley Plates (17).
USING OLYMPIC WEIGHTS ON THE LEG LEVER
To use Olympic weights on the Leg Lever (62), insert
the Weight Adapter Bushings (68) into the ends of the
Weight Adapter (76). Slide the Weight Adapter over the
weight tube on the Leg Lever. Insert the Weight Adapter
Pin (73) into the weight tube.
62
76
73
68
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Exercise Guidelines
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
Muscle Building
Specifying the exact length of time for each workout,
as well as the number of repetitions or sets for each
exercise, is a highly individual matter. It is very impor-
tant to avoid overdoing it during the first few months
of your exercise program. You should progress at
your own pace and be sensitive to your body’s sig-
nals. If you experience pain or dizziness at any time
while exercising, stop immediately and begin cooling
down. Find out what is wrong before continuing.
Remember that adequate rest and a proper diet are
important factors in any exercise program.
The only way to increase the size and strength of
your muscles is to push them close to their maximum
capacity. When you progressively increase the inten-
sity of your exercise, your muscles will continually
adapt and grow. You can tailor the individual exercise
to the proper intensity level in two ways:
• by changing the amount of weight used
• by changing the number of repetitions or sets per-
formed (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions).
WARMING UP
The proper amount of weight for each exercise obvi-
ously depends upon the individual user. You must
gauge your limits and select the amount of weight that
is right for you. Begin with 3 sets of 8 repetitions for
each exercise you perform. Rest for 3 minutes after
each set. When you can complete 3 sets of 12 repeti-
tions without difficulty, increase the amount of weight.
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
WORKING OUT
Toning
You can tone your muscles by pushing them to a
moderate percentage of their capacity. Select a mod-
erate amount of weight and increase the number of
repetitions in each set. Complete as many sets of 15
to 20 repetitions as possible without discomfort. Rest
for 1 minute after each set. Work your muscles by
completing more sets rather than by using high
amounts of weight.
Each workout should include 6 to 10 different exercis-
es. Select exercises for every major muscle group
with emphasis on the areas that you want to develop
the most. To give balance and variety to your work-
outs, vary the exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
You will gain the greatest benefits from exercising by
maintaining proper form. This requires moving
through the full range of motion for each exercise and
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise poster accompa-
nying this manual, you will find photographs showing
the correct form for several exercises. A description of
each exercise is also provided, along with a list of the
muscles affected. Refer to the muscle chart on page
18 to find the locations of the muscles.
Cross Training
Many people desire a complete and balanced fitness
program. Cross training is an efficient way to accom-
plish this. One example of a balanced program is:
• Plan weight training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
cycling, running, or swimming on Tuesday and
Thursday.
• Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The combination of weight training and aerobic exer-
cise will reshape and strengthen your body and devel-
op your heart and lungs.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure to rest for a short period of time after each
set. The ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is very effective for increasing flexibility.
• Rest for one minute after each set for a toning work-
out.
STAYING MOTIVATED
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
For motivation, keep a record of each workout. The
chart on page 19 of this manual can be photocopied
and used to schedule and record your workouts. List
the date, the exercises performed, the weight, and the
numbers of sets and repetitions completed. Record
your weight and key body measurements at the end
of every month.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
Remember, the key to achieving the greatest results
is to make exercise a regular and enjoyable part of
your everyday life.
MUSCLE CHART
Trapezius
Pectoralis
Major
Deltoid
Trapezius
Rectus
Abdominus
Biceps
Deltoid
Obliques
Brachioradials
Rhomboideus
Triceps
Abductor
Latissimus Dorsi
Spinae Erectors
Brachioradials
Hip Flexors
Quadriceps
Adductor
Gluteus
Medius
Gluteus
Maximus
Soleus
Abductors
Hamstring
Gastrocnemius
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
R0201A
Part List—Model No. IMBE39401
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
6
2
2
2
1
1
1
1
1
1
2
2
2
2
2
12
6
2
7
1
4
5
5
61
4
36
3
4
9
2
8
20
2
1
2
4
2
2
1
1
Right Base
Center Base
Left Base
Weight Guide Base
Foot Plate
Rack Joint Plate
Front Upright
Rear Upright
Weight Guide
Right Frame
Center Frame
Left Frame
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
#
1
2
1
1
4
4
1
1
1
1
2
2
1
1
1
3
1
2
1
2
2
1
2
6
6
2
6
1
5
5
1
1
1
1
1
1
1
1
1
4
2
1
1
1
Cable Clip
Handgrip
Bench Leg
Adjustable Bench Leg
M6 x 16mm Screw
M6 x 52mm Screw
Bench Frame
Bench Base
Curl Pad
Curl Upright
51mm x 76mm Outer Cap
M10 x 58mm Carriage Bolt
Stabilizer
Seat
Backrest
Pad Tube
Leg Lever
Bench Joint Plate
Bench Base Joint Plate
50mm Square Outer Cap
M10 x 192mm Bolt
Seat Mounting Bracket
Weight Adapter Bushing
Foam Pad
19mm Round Inner Cap
Backrest Tube
25mm x 38mm Inner Cap
Weight Adapter Pin
M6 Washer
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Chin-up Bar
Weight Guide Frame
Weight Carriage
Carriage Bushing
Pulley Plate
Weight Bumper
Weight Rest
Safety Spotter
Square Bushing
Adjustment Knob
Cable Trap
Pulley
Low Cable
45mm Square Inner Cap
60mm Square Outer Cap
60mm Square Inner Cap
M10 Nylon Locknut
M8 Nylon Locknut
M10 x 78mm Bolt
M10 x 45mm Bolt
M8 x 72mm Bolt
M10 x 72mm Bolt
M10 x 66mm Bolt
M8 Washer
M10 x 68.5mm Bolt
Weight Adapter
20mm x 40mm Inner Cap
M6 x 35mm Screw
Backrest Adjustment Bracket
Seat Adjustment Bracket
Small Adjustment Knob
25mm Angled Outer Cap
25mm Round Inner Cap
High Cable
18mm Spacer
M10 x 50mm Bolt
Allen Wrench
User’s Manual
Exercise Poster
M10 Washer
24mm Spacer
51mm Spacer
28mm Spacer
Weight Clip Sleeve
51mm Round Inner Cap
Weight Clip
#
#
Strap
Lat Bar
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
R0201A
Exploded Drawing—Model No. IMBE39401
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Replacement Parts
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information when calling:
• The MODEL NUMBER of the product (IMBE39401)
• The NAME of the product (IMAGE® 5.5 weight rack)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING at the center of this manual).
Limited Warranty
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which war-
ranty claim is made must be received by ICON at one of its authorized service centers with all freight and other
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-autho-
rized by ICON. This warranty does not extend to any product or damage to a product caused by or attribut-
able to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center, products used for commercial or rental purposes, or products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential dam-
ages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 171513 R0201A
Printed in China © 2000 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|