®
Model No. 831.159701
Serial No.
USER’S MANUAL
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
SEARS, ROEBUCK AND CO.
HOFFMAN ESTATES, IL 60179
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before
using this equipment. Save this
manual for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Precautions
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the weight bench.
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
12. Always set both safety spotters at the same
height.
13. Always wear athletic shoes for foot protec-
tion while exercising.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
14. The weight bench is designed to support a
maximum of 560 pounds, including the user,
a barbell and weights (not included). Do not
place more than 310 pounds, including the
barbell, on the weight gliders and safety
spotters.
3. The weight bench is intended for home use
only. Do not use the weight bench in a com-
mercial, rental or institutional setting.
4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench for
protection.
15. The decals shown below have been placed
on the weight bench. If a decal is missing or
illegible, please call our toll-free HELPLINE at
1-800-736-6879, Monday through Saturday, 7
a.m. until 7 p.m. Central Time, to order a free
replacement decal. Apply the decal in the
location shown.
5. Inspect and tighten all parts each time you
use the weight bench. Replace any worn
parts immediately.
6. Keep children under 12 and pets away from
the weight bench at all times.
7. Keep hands and feet away from moving
parts.
8. Always secure your weights (not included)
with weight clips when they are mounted on
the barbell.
9. Always make sure there is an equal amount
of weight (not included) on each side of the
barbell.
10. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
11. Always move the bench out of the way when
performing an exercise that does not use the
bench.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. SEARS assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Thank you for selecting the versatile IMAGE® 3.8
at 1-800-736-6879, Monday through Saturday, 7 a.m.
weight bench. The IMAGE® 3.8 is designed to help you until 7 p.m. Central Time (excluding holidays). To help
develop every major muscle group of the body.
Whether your goal is a shapely figure, dramatic mus-
cle size and strength, or a healthier cardiovascular
us assist you, please note the product model number
and serial number before calling. The model number is
831.159701. The serial number can be found on a
system, the IMAGE® 3.8 will help you achieve the spe- decal attached to the weight bench (see the front
cific results you want.
cover of this manual).
For your benefit, read this manual carefully before
using the IMAGE® 3.8 weight bench. If you have
additional questions, please call our toll-free HELPLINE
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Note: The terms “right side” and “left side”
are determined relative to a person sitting
on the bench. They do not refer to right
and left on the drawings in this manual.
Right Side
Weight Guide
Left Side
Upright
Barbell
Weight Glider
Weight
Storage
Tube
Safety Spotter
Backrest
Seat
Adjustment
Bracket
4
Download from Www.Somanuals.com. All Manuals Search And Download.
R1200A
Part Identification Chart—Model No. 831.159701
M6 x 55mm Bolt (4)—4
M6 x 38mm Bolt (60)—1
M6 x 16mm Screw (3)—2
M6 Washer (30)—5
M10 Washer (6)—14
M8 Nylon Locknut (54)—11
M8 Washer (52)—10
M10 Nylon Locknut (11)—26
M8 x 70mm Bolt (41)—4
M10 x 25mm Bolt (43)—2
M8 x 65mm Carriage Bolt (59)—4
M10 x 65mm Carriage Bolt (40)—8
M8 x 60mm Bolt (39)—2
M10 x 65mm Bolt (42)—4
M8 x 30mm Bolt (38)—2
M10 x 70mm Bolt (46)—8
M10 x 25mm Bolt (53)—2
M10 x 80mm Bolt (56)—1
M8 x 20mm Screw (50)—2
M10 x 115mm Bolt (55)—1
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Before beginning assembly, carefully read the
following information and instructions:
• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5. Note:
Some small parts may be pre-assembled.
Make Things Easier for Yourself!
In addition to the included allen wrench
assembly requires the following tools (not
included):
,
This manual is designed to ensure that the
weight bench can be assembled successfully
by anyone. By setting aside plenty of time, and
by deciding to make the task enjoyable,
assembly will go smoothly.
• Two (2) adjustable wrenches
• One (1) rubber mallet
• Assembly requires two people.
• One (1) standard screwdriver
• One (1) phillips screwdriver
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
• Lubricant, such as grease or petroleum jelly,
and soapy water.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches or a set of ratchet wrenches.
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
1. Before beginning, make sure that you understand
the information in the box above. Note: Some
parts described in the assembly steps may be
pre-assembled.
1
Decal
54
17
20
54
12
Press a 50mm Square Outer Cap (17) onto each end
of a Base (7). Turn the Base so the large hole is in
the position shown. Insert two M8 x 65mm Carriage
Bolts (59) and two M10 x 65mm Carriage Bolts (40)
up into the indicated holes in the Base. Place the
Base flat on the floor.
Large Hole
41
7
17
2
59
Turn the Base Crossbar (20) so the warning decal is
positioned as shown. Attach the Base (7) to the Base
Crossbar with two M8 x 70mm Bolts (41), a Large
Support Plate (12), and two M8 Nylon Locknuts (54).
Do not tighten the Nylon Locknuts yet.
40
17
12
41
2. Press a 50mm Square Outer Cap (17) onto each end
of the other Base (7). Turn the Base so the large hole
is in the position shown. Insert two M8 x 65mm
Carriage Bolts (59) and two M10 x 65mm Carriage
Bolts (40) up into the indicated holes in the Base.
Place the Base flat on the floor.
54
20
Large Hole
7
54
17
59
Attach the Base (7) to the Base Crossbar (20) with
two M8 x 70mm Bolts (41), a Large Support Plate
(12), and two M8 Nylon Locknuts (54). Do not tighten
the Nylon Locknuts yet.
40
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Slide a Brace (2) onto the bracket on one of the
Uprights (1). Attach the Brace to the Upright with two
M10 x 65mm Bolts (42), four M10 Washers (6), and
two M10 Nylon Locknuts (11). Do not tighten the
Nylon Locknuts yet.
3
1
Slide the Upright (1) and the Brace (2) onto the M10
x 65mm Carriage Bolts (40) and the M8 x 65mm
Carriage Bolts (59) in the left Base (7). Attach the
Upright with two M10 Nylon Locknuts (11). Attach the
Brace with two M8 Washers (52) and two M8 Nylon
Locknuts (54). Do not tighten the Nylon Locknuts
yet.
11
6
2
6
42
Bracket
54
52
11
40
59
7
4. Slide the remaining Brace (2) onto the bracket on the
other Upright (1). Attach the Brace to the Upright with
two M10 x 65mm Bolts (42), four M10 Washers (6),
and two M10 Nylon Locknuts (11). Do not tighten
the Nylon Locknuts yet.
4
1
Slide the Upright (1) and the Brace (2) onto the M10
x 65mm Carriage Bolts (40) and the M8 x 65mm
Carriage Bolts (59) in the right Base (7). Attach the
Upright with two M10 Nylon Locknuts (11). Attach the
Brace with two M8 Washers (52) and two M8 Nylon
Locknuts (54). Do not tighten the Nylon Locknuts
yet.
42
6
2
11
6
Bracket
54
52
59
7
11
40
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Press a 25mm Round Inner Cap (51) into the end of
a Weight Storage Tube (21).
5
2
While a second person holds a Crossbar (8) in the
position shown, insert two M10 x 70mm Bolts (46)
through the bracket on the Weight Storage Tube (21),
the left Brace (2), and the bracket on the Crossbar.
Thread an M10 Nylon Locknut (11) onto each Bolt.
Do not tighten the Nylon Locknuts yet.
8
21
46
11
46
51
6. Press a 25mm Round Inner Cap (51) into the end of
the other Weight Storage Tube (21).
6
51
46
21
While a second person continues to hold the
Crossbar (8), insert two M10 x 70mm Bolts (46)
through the bracket on the Weight Storage Tube (21),
the right Brace (2), and the bracket on the Crossbar.
Thread an M10 Nylon Locknut (11) onto each Bolt.
Do not tighten the Nylon Locknuts yet.
46
2
8
11
7. Have a second person hold the other Crossbar (8)
between the Uprights (1).
7
Attach the Crossbar (8) to the left Upright (1) with two
M10 x 70mm Bolts (46), a Small Support Plate (16),
and two M10 Nylon Locknuts (11). Do not tighten
the Nylon Locknuts yet.
11
46
16
8
11
11
46
Attach the Crossbar (8) to the right Upright (1) with
two M10 x 70mm Bolts (46), a Small Support Plate
(16), and two M10 Nylon Locknuts (11). Do not tight-
en the Nylon Locknuts yet.
11
16
46
1
1
46
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Press a 25mm Bushing (48) into each end of the
Locking Bar (34).
8
Insert the Barbell (35) through the Locking Bar (34)
until the Barbell is centered in the Locking Bar.
48
34
35
48
9. Identify the Left Weight Glider (32) by looking at the
position of the round tube.
9
Press a 38mm Bushing (29) into each end of the
round tube on the Left Weight Glider (32).
32
29
Slide the Left Weight Glider (32) onto the left end of
the Barbell (35). Secure the Weight Glider to the
Barbell with a hand-tightened M8 x 20mm Screw (50).
Look at the drawing on page 4 to make sure that
you have correctly identified the left end. The Left
Weight Glider must be turned as shown in the
drawing.
35
50
29
Round tube
10. Identify the Right Weight Glider (31) by looking at the
position of the round tube.
10
29
50
Press a 38mm Bushing (29) into each end of the
welded tube on the Right Weight Glider (31).
29
Slide the Right Weight Glider (31) onto the right end
of the Barbell (35). Secure the Weight Glider to the
Barbell with a hand-tightened M8 x 20mm Screw (50).
Make sure that the Weight Glider is turned as
shown in the drawing.
35
Round
tube
31
11. Identify the Left Safety Spotter (24) by the position of
the handle and the Left Spotter Hook (62). Place the
Left Safety Spotter on the left Base (7) so it is cen-
tered over the indicated hole.
11
18
1
Have a second person hold the Locking Bar (34) so
that the Left Weight Glider (32) rests on top of the
Left Safety Spotter (24). Insert a Weight Guide (18)
into the Left Weight Glider, the Left Safety Spotter,
and the hole in the Base (7). Note: Tilt the Weight
Guide away from the Upright (1) as you insert it.
34
32
Handle
62
24
7
54
52
Attach the Weight Guide (18) to the Base (7) with an
M8 x 60mm Bolt (39), two M8 Washers (52), and an
M8 Nylon Locknut (54). Do not tighten the Nylon
Locknut yet.
Hole
39
9
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Place the Right Safety Spotter (23) on the right Base
(7) and center it over the indicated hole. Note: The
handle must point toward the center of the bench.
12
18
31
Have a second person hold the Locking Bar (34) so
that the Right Weight Glider (31) rests on top of the
Right Safety Spotter (23). Insert a Weight Guide (18)
into the Right Weight Glider, the Right Safety Spotter,
and the hole in the Base (7). Note: It may be neces-
sary to tilt the Weight Guide away from the
Upright (1) as you insert it.
1
34
Handle
7
Hole
54
23
39
52
Attach the Weight Guide (18) to the Base (7) with an
M8 x 60mm Bolt (39), two M8 Washers (52), and an
M8 Nylon Locknut (54). Do not tighten the Nylon
Locknut yet.
13. Note: If you are not planning to use Olympic
weights with the weight bench, you do not need
to perform this step. Keep the two Weight
Adapters (33) in a safe place in case you need
them in the future.
13
Fully engage the indicated hook on both sides of
the weight bench before beginning this step.
Insert a 50mm Bushing (47) into the end of a Weight
Adapter (33). With a second person holding the
Barbell (35) so that it cannot turn, use the allen
wrench to secure the Weight Adapter to the Barbell
with a Large Washer (44) and an M10 x 25mm Bolt
(43). Note: The Large Washer must fit into the
indentation in the 50mm Bushing in the Weight
Adapter.
Hook
35
33
47
44
43
Pull the remaining length of the Barbell (35) in the
direction shown. Next, tighten the M8 x 20mm
Screws used in steps 9 and 10. Attach the other
Weight Adapter (33) to the other end of the Barbell in
the same manner.
14. Attach the upper end of one of the Weight Guides
(18) to the bracket on the Upright (1) with an M8 x
30mm Bolt (38) and an M8 Washer (52).
14
38
Attach the other Weight Guide (18) to the other
Upright (1) in the same manner.
52
Tighten all of the Nylon Locknuts used in steps 1
to 14.
18
1
10
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Press a 50mm Square Outer Cap (17) onto each end
of the Small Stabilizer (25).
15
16
17
11
5
Attach the Small Stabilizer (25) to the Bench Frame
(5) with two M10 x 65mm Carriage Bolts (40) and two
M10 Nylon Locknuts (11). Note: There is an inden-
tation around the holes on one side of the Small
Stabilizer. This side must be facing the floor.
17
25
17
40
16. Press a 50mm x 70mm Outer Cap (10) onto each
end of the Large Stabilizer (26).
11
Turn the Large Stabilizer (26) so the warning decal is
in the position shown. Attach the Large Stabilizer to
the Bench Frame (5) with two M10 x 65mm Carriage
Bolts (40) and two M10 Nylon Locknuts (11). Note:
There is an indentation around the holes on one
side of the Large Stabilizer. This side must be fac-
ing the floor.
5
Decal
10
10
26
40
17. Press two 20mm x 40mm Inner Caps (28) into each
Backrest Tube (27). Press four 20mm x 40mm Inner
Caps into the Backrest Adjustment Bracket (36).
Lubricate
28
27
22
6
Lubricate an M10 x 180mm Bolt (22). Attach the
Backrest Tubes (27) to the welded tube on the
Backrest Adjustment Bracket (36) with the Bolt, two
M10 Washers (6), and an M10 Nylon Locknut (11).
Make sure that the Backrest Tubes are turned as
shown. The indicated holes are not centered in
the Backrest Tubes but are closer to one side.
Turn the Backrest Tubes so the holes are closer
to the floor. Do not over tighten the Nylon
6
Holes
11
28
28
28
Welded
Tube
36
Locknut; the Backrest Tubes must pivot easily.
18. Lubricate an M10 x 115mm Bolt (55). Slide an M10
Washer (6) onto the Bolt. Hold the hole in the
Backrest Adjustment Bracket (36) on the outside of
the bracket on the Bench Frame (5).
18
55
27
Lubricate
36
Inserting the M10 x 115mm Bolt (55) through the one
side of the Backrest Adjustment Bracket, one side of
the bracket on the Bench Frame, and through the
15mm x 10.2mm x 60mm Spacer (57). Then, insert
the Bolt through the other side of the bracket on the
Bench Frame and the Backrest Adjustment Bracket.
Secure the Bolt with an M10 Washer (6) and an M10
Nylon Locknut (11). Do not over tighten the Nylon
Locknut.
Hole
6
57
11
6
Bracket
5
11
Download from Www.Somanuals.com. All Manuals Search And Download.
19. Lubricate an M10 x 180mm Bolt (22). Attach the
Backrest Tubes (27) to the indicated tube on the
Bench Frame (5) with the Bolt, two M10 Washers (6),
and an M10 Nylon Locknut (11). Note: Do not over
tighten the Nylon Locknut; the Backrest Tubes
must pivot easily.
19
Lubricate
6
27
22
5
11
27
Tube
6
20. Attach the Backrest (15) to the Backrest Tubes (27)
with four M6 x 55mm Bolts (4) and four M6 Washers
(30).
20
15
30
4
30
30
9
4
21. Press a 25mm x 50mm Inner Cap (58) into the open
end of the Seat Support Tube (37).
21
45
Lubricate an M8 x 80mm Bolt (9). Attach the Seat
Adjustment Bracket (45) to the indicated side of the
Seat Support Tube (37) with the Bolt and an M8
Nylon Locknut (54). Note: Do not over tighten the
Nylon Locknut; the Seat Adjustment Bracket must
pivot easily.
37
Lubricate
54
58
22. Place the Seat Support Tube (37) on the Bench
Frame (5) so that the Seat Adjustment Bracket (45)
fits over the welded pin (not visible in the drawing) on
the side of the Bench Frame.
22
37
Lubricate
Lubricate an M10 x 80mm Bolt (56). Attach the Seat
Support Tube (37) to the indicated bracket on the
Bench Frame (5) with the Bolt and an M10 Nylon
Locknut (11). Note: Do not over tighten the Nylon
Locknut; the Seat Support Tube must pivot easily.
45
56
Welded
Pin
5
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
23. Turn the Seat (14) as shown. Attach the wide end of
the Seat to the bracket on the Seat Support Tube
(37) with two M6 x 16mm Screws (3).
23
14
Tilt the Seat Support Tube (37) upwards and attach
the narrow end of the Seat (14) to the Seat Support
Tube with an M6 x 38mm Bolt (60) and an M6
Washer (30).
37
30
60
3
24. Make sure that all parts are properly tightened before you use the weight bench. The use of all
remaining parts will be explained in ADJUSTING THE WEIGHT BENCH starting on the following page.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Weight Bench
This section explains how the weight bench is adjusted. See the included exercise guide for important informa-
tion about how to perform a variety of exercises and how to get the greatest benefit from your exercise program.
Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The
weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
USING THE LOCKING BAR AND SAFETY SPOTTERS
Before starting an exercise, position the Barbell (35) and
the Safety Spotters (23, 24) in the correct position for that
exercise.
1
1
To do this, stand in front of the cage and grip the Locking
Bar (34) with both hands. Turn the Locking Bar until the
two hooks disengage the slots in the Uprights (1). Move
the Locking Bar to a new position and turn the Locking
Bar until the hooks engage the slots in the Uprights.
Note: Always start an exercise with the barbell posi-
tioned at the lowest point to which it will move during
the exercise.
31
23
34
35
32
24
Position both Safety Spotters (23, 24) directly under the
Weight Gliders (31, 32).
USING THE SAFETY SPOTTERS
To move a Safety Spotter (23, 24 [not shown]) to a new
position, grip the handle on the side of the Spotter Hook
(61, 62 [not shown]) and pull the Spotter Hook out of the
slot in the Upright (1). Raise or lower the Safety Spotter
to a new position and turn the Spotter Hook until it
engages one of the slots in the Upright.
1
61
Handle
23
WARNING:
Always set both Safety
Spotters at the same height.
ATTACHING WEIGHTS TO THE BARBELL
To use the Barbell (35), slide the desired amount of
weight (not included) onto each end of the Barbell.
Secure the weights with the Large Weight Clips (13).
Note: To use standard weights, the Weight Adapters (33)
should be removed from the Barbell. Attach weights to
the Barbell with the Small Weight Clips (not shown).
33
35
13
WARNING:
Do not place more than
260 pounds on the barbell. Always secure the
weights with weight clips when they are on the bar-
bell. Always place the same amount of weight on
each side of the barbell.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE BACKREST
15
To raise the Backrest (15), grip the end of the Backrest
with one hand and pull it upward. The Backrest
Handle
Adjustment Frame (36) will automatically lock into one of
the tabs on the bracket on the Bench Frame (5).
To lower the Backrest (15), grip the end of the Backrest
with one hand and pull it slightly upwards. Grip the handle
(not shown) on the right side of the Backrest Adjustment
Frame (36) with your other hand and pull the Backrest
Adjustment Frame free of the tabs on the bracket on the
Bench Frame (5). Lower the Backrest to the desired posi-
tion and lock the Backrest Adjustment Frame into the
desired tab on the bracket on the Bench Frame.
36
5
Adjustment
Bracket
ADJUSTING THE SEAT
To raise the Seat (14), lift the narrow end of the Seat until
the appropriate tab on the Seat Adjustment Bracket (45)
engages the welded pin (not shown) on the right side of
the Bench Frame (5).
To lower the Seat (14), use the handle on the Seat
Adjustment Bracket (45) to disengage the Seat
Adjustment Bracket from the pin. Lower the Seat to the
desired position and engage the appropriate tab on the
Seat Adjustment Bracket to the pin.
45
Handle
Pin
14
5
15
Download from Www.Somanuals.com. All Manuals Search And Download.
R1200A
Part List—Model No. 831.159701
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
2
2
2
4
1
14
2
2
1
2
26
2
2
1
1
2
6
2
2
1
2
2
1
1
1
1
2
8
4
5
1
1
2
Upright
Brace
M6 x 16mm Screw
M6 x 55mm Bolt
Bench Frame
M10 Washer
Base
Crossbar
M8 x 80mm Bolt
50mm x 70mm Outer Cap
M10 Nylon Locknut
Large Support Plate
Large Weight Clip
Seat
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
#
1
1
1
1
2
2
8
4
4
2
2
1
8
2
2
8
2
2
10
2
11
1
1
1
1
4
1
1
1
1
1
1
Locking Bar
Barbell
Backrest Adjustment Bracket
Seat Support Tube
M8 x 30mm Bolt
M8 x 60mm Bolt
M10 x 65mm Carriage Bolt
M8 x 70mm Bolt
M10 x 65mm Bolt
M10 x 25mm Bolt
Large Washer
Seat Adjustment Bracket
M10 x 70mm Bolt
50mm Bushing
25mm Bushing
45mm x 45mm Bushing
M8 x 20mm Screw
25mm Round Inner Cap
M8 Washer
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Backrest
Small Support Plate
50mm Square Outer Cap
Weight Guide
Small Weight Clip
Base Crossbar
Weight Storage Tube
M10 x 180mm Bolt
Right Safety Spotter
Left Safety Spotter
Small Stabilizer
Large Stabilizer
Backrest Tube
20mm x 40mm Inner Cap
38mm Bushing
M6 Washer
M10 x 25mm Bolt
M8 Nylon Locknut
M10 x 115mm Bolt
M10 x 80mm Bolt
15mm x 10.2 mm x 60mm Spacer
25mm x 50mm Inner Cap
M8 x 65mm Carriage Bolt
M6 x 38mm Bolt
Right Spotter Hook
Left Spotter Hook
User’s Manual
Right Weight Glider
Left Weight Glider
Weight Adapter
#
#
Exercise Guide
6mm Allen Wrench
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
R1200A
Exploded Drawing—Model No. 831.159701
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Replacement Parts
The model number and serial number of your IMAGE 3.8 are list-
ed on a decal attached to the frame. See the front cover of this
manual to find the location of the decal.
Model No. 831.159701
All replacement parts are available for immediate purchase or
special order when you visit your nearest SEARS Service
Center. To request service or to order parts by telephone, call the
toll-free numbers listed at the left.
QUESTIONS?
If you find that:
When requesting help or service, or ordering parts, please be
prepared to provide the following information:
• you need help assembling or
operating the IMAGE 3.8
• The MODEL NUMBER of the product (831.159701)
• The NAME of the product (IMAGE 3.8 weight bench)
• a part is missing
• or you need to schedule repair
service
• The PART NUMBER of the PART (see the PART LIST and the
EXPLODED DRAWING at the center of this manual)
call our toll-free HELPLINE
1-800-736-6879
Monday–Saturday, 7 am–7 pm
Central Time (excluding holidays)
• The DESCRIPTION of the PART (see the PART LIST and the
EXPLODED DRAWING at the center of this manual).
REPLACEMENT
PARTS
If parts become worn and need to
be replaced, call the following toll-
free number
1-800-FON-PART
(1-800-366-7278)
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
Full 90 Day Warranty
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
SEARS WEIGHT BENCH EXERCISER, contact the nearest SEARS Service Center throughout the United
States and SEARS will repair or replace the WEIGHT BENCH EXERCISER, free of charge.
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for rental
purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
Part No. 172630 R1200A
Printed in China © 2000 Sears, Roebuck and Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
|