Stereo Audio System for Your iPod®
Instruction Manual
Model: i199
Please read this manual carefully before operating and save it for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
USER SAFETY GUIDE
INSTRUCTIONS ON ENVIRONMENT PROTECTION
Do not dispose of this product in the usual household garbage at the end of its life cycle; bring it to a collection point for the recycling of
electrical and electronic appliances. This symbol on the product means the instructions for use or the packing will inform about the methods
for disposal. The materials are recyclable as mentioned in its marking. By recycling, material recycling, or other forms of re-utilization of old
appliances, you make an important contribution to protect the environment. Please inquire at your local community administration for the
authorized disposal location.
FCC RULES
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
Do not make changes or modify the device in any way. Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
IMPORTANT SAFETY WARNINGS
1. Before using the player, please ensure that your local AC voltage is suitable for this unit.
2. To prevent fire or electric shock, do not expose the unit to rain or moisture.
3. Never attempt to open the cabinet. Always refer servicing to a qualified technician.
IMPORTANT SAFETY INSTRUCTIONS
1. READ INSTRUCTIONS – All the safety and operating instructions should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS – The safety and operating instructions should be retained in a secure place for future reference.
3. HEED WARNINGS – All warnings on the appliance and in the operating instructions should be observed.
4. FOLLOW INSTRUCTIONS – All operating and use instructions should be followed.
5. WATER AND MOISTURE – The appliance should not be used near water. For example: near a bathtub, kitchen sink, laundry tub, and/or swimming
pool.
6. HEAT – The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers)
that produce heat.
Download from Www.Somanuals.c-om2. -All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
USER SAFETY GUIDE
IMPORTANT SAFETY INSTRUCTIONS – CONTINUED
7. POWER SOURCES – The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on
the appliance itself.
8. CLEANING – The appliance should be cleaned with a dry cloth.
9. OBJECT AND LIQUID ENTRY – Care should be taken so that objects do not fall and liquids are not spilled into the device’s openings.
10. CARTS AND STANDS – The appliance should be used only with a cart or stand that is recommended by the manufacturer. An
appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
11. DAMAGE REQUIRING SERVICE – The appliance should be serviced by qualified service professional when:
a. The power supply cord or plug has been damaged.
b. Objects have fallen into, or liquid has been spilled into the appliance’s apertures.
c. The appliance has been exposed to rain.
d. The appliance has been dropped and suffered damage.
e. The appliance does not appear to operate normally or exhibits a change in performance.
12. SERVICING – The user should not attempt to service the appliance beyond what is described in the user's operating instructions. All other servicing
should be referred to qualified service professional.
13. BATTERY USAGE – To prevent battery leakage, which may result in bodily injury, property damage or damage to the unit, follow these instructions:
a. Install all batteries correctly according to the polarity (+/-) as marked on the unit.
b. Do not mix old and new batteries, carbon and alkaline, etc.
c. Remove batteries from the unit when the device will not be used for an extended period of time.
14. LEAD AND MERCURY – This product may contain lead and/or mercury. Disposal of these materials may be regulated by your local authorities due to
environmental considerations. For more detailed disposal or recycling information, please contact your local authorities or the EIA (Electronic Industries
Download from Www.Somanuals.c-om3. -All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
USER SAFETY GUIDE
FCC NOTICE (USA)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
IC NOTICE (CANADA)
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of
Industry Canada. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television operation (which can be determined by turning the equipment off), the user is encouraged to try to correct the interference
by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Download from Www.Somanuals.c-om4. -All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
USER SAFETY GUIDE
About Electromagnetic Interference (EMI)
This device is designed and manufactured not to exceed the exposure limit for radio frequency energy, which is set by the Federal Communications
Commission of the U.S government.
The term “EMI” is short for the electromagnetic interference caused by the electromagnetic field generated by electronic devices. In fact, most electrical
appliances and devices emit electric and magnetic fields, and most of modern electronic devices are susceptible to the EMI if they are inadequately shielded
or designed.
•
If you use any personal medical device, such as a pacemaker, please consult the manufacture of your medical device to determine if it is adequately
shielded from EMI. Your physician might assist you in obtaining this information.
•
•
Please turn off this device if you are instructed to do so, especially on an airplane or in a hospital.
Please keep away from medical instruments in a hospital or medical unit while using this device.
IMPORTANT NOTES ON HEARING
Your hearing is very important to you and to us. We strongly recommend you to follow the guideline below in order to prevent possible damage to or loss of
hearing. Hearing experts caution that listening to loud sounds can damage hearing over time. With continuous listening to loud sounds, hearing adapts and
will give the impression that volume has reduced. What seems normal may, in fact, be harmful. To guard against this before hearing adapts, set the volume
at a low level and slowly increase the volume level until sound can be heard comfortably and clearly without distortion. Damage to hearing is cumulative and
irreversible. Ringing or discomfort in the ears indicates that the volume is too loud. Once a comfortable listening level has been established, do not increase
the volume level further.
Cautions
•
•
If you experience a ringing sound in your ear, lower the volume or discontinue the use of this product.
Do not use the headphones while driving or cycling. Because this product reduces the external noises, you might not be able to hear the warning sounds,
such as an automobile horn, and might result in a traffic accident. Additionally, listening to headphones while driving is illegal in many places
Warning: to prevent fire or shock hazard, don’t expose this appliance to rain or moisture.
These markings are located on the bottom, side or back of the unit.
Download from Www.Somanuals.c-om5. -All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
Download from Www.Somanuals.c-om6. -All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
TABLE OF CONTENTS
Getting Started
General features ……………………………………………………………………………………………………………………………………………...…
Installing the AC Power …………….……………………………………………………………..……………………………………………………………
Installing the backup battery for clock and alarm settings ………………..……………………….……………………………………………………….
8
9
9
Installing the remote control battery ….....………………………………………………………………………………………………………….………… 11
Installing the AM loop antenna ………………………………………………………………………………………………………………………….…….. 11
Installing the dock adapter …………………………………………………………………………………………………………………………………….. 11
Location of controls on the main unit ……………………………………………………………………………………………………………….…...……
12
Location of controls on the remote control …………………………………………………………………………………………………………………... 13
Location of indications on the LCD screen …...……………………………………………………………………………………………………………...
14
Operational Instructions
Setting the clock …….....……………………………………………………………………….………………………………………………………………. 15
Setting the alarm ………..………….………………………………………………………………………………………………………………….……..… 15
Using the alarm function ……..………………………………………………………………………………………………………………………………...
Adjusting the brightness of the LCD screen………………………………………………………………………………………………………………….. 16
Setting the sleep time ……………………….…………………………………………………………………………………………………………………. 17
Listening to your favorite radio stations …….………………………………………………………………………………………………………………... 17
Listening to your favorite songs on your iPod ..…….……………………………………………………………………………………………………….. 18
Listening to CDs/MP3-CDs…………………………………………………………………………………………………………………………………….. 19
Listening to your favorite music on a USB storage device…………………………………………………………………………………………………. 22
Using the AV out port to watch videos from your iPod on an external monitor or TV …….…………………………………………………………….. 22
15
Listening to other audio devices using the line-out port…………………………………………………………………………………………………….
Charging your iPod ……………………………………………………………………………………………………………………………………………..
24
24
BluePin Setup and operating Instructions ………………………………………………………………………………………………………..………….. 25
Maintenance & Troubleshooting Guide ……………………………………………………………………………………………………………..…………..
Specifications ………………………………………………………………………………………………………………………………………………………..
30
33
Download from Www.Somanuals.c-om7. -All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
GETTING STARTED
Congratulations on your purchase of the new iLuv i199 for your iPod. Uniquely designed to work with your iPod, this iLuv stereo audio system with built-in
universal dock provides advanced audio and radio performance that brings out the best in your music. Remember to keep this manual for future reference.
Maximize Your Enjoyment of the Music on Your iPod with the iLuv Stereo Audio System
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Enjoy Wireless freedom with new BluePinTM adapter w/ Bluetooth Wireless Technology
Enhance the richness of your iPod sound with jAuraTM acoustic speaker technology
Powerful built-in speakers allow you to hear music with depth and clarity
Watch your favorite videos on your TV if your iPod has the video capability
Digital clock display with dual alarm
Fall asleep or wake up to your iPod, CD, USB device, AM/FM radio, or buzzer
Charges your iPod
Integrated universal dock for your iPod
MP3 CD / Audio CD playback with ESP anti-shock system
Capable of playing MP3 files on USB devices, such as MP3 player, flash memories, etc
Auxiliary line input for 1st , 2nd and 3rd generations of the iPod and other audio devices
AM/FM radio with PLL digital tuning technology
External loop antenna provides better AM reception
Liquid crystal display with white backlight
Remote control included
What’s included?
•
•
•
BluePinTM Adapter
•
Dock adapters
•
•
AM loop antenna
•
•
Instruction manual
Warranty card
Stereo audio system
AV (3.5mm to RCA) cable
Remote control (Battery included)
•
Made for iPod with video (30GB, 60GB, 80GB), iPod nano (1st generation, 2nd generation), iPod mini, iPod 4G only.
Note: All iPod shuffle or other device users have to use the Line-In feature of i199 to listen to music stored on these players.
Download from Www.Somanuals.c-om8. -All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
GETTING STARTED
IMPORTANT:
1. Occasionally, files on your iPod can become corrupted. This may cause an erratic behavior with your iLuv products. Apple Computer recommends that
2. It is imperative that you use the correct dock adapter for your iPod and that the dock adapter fits appropriately into the built-in universal dock. Ignoring
these rules can cause severe damage to your iPod. Please refer to the section “Installing the Dock Adapter” to properly install the dock adapter before
operating the i199 with your iPod.
Using AC Power
Locate the AC power plug on the back of the unit. Insert the end of the supplied power cord into the wall outlet.
Installing the Backup Battery for Clock and Alarm Settings
In order to offer consistent clock settings and alarm functions, the i199 uses a Backup Battery system. This means that in the event of a power failure, all the
settings of the i199 will remain saved. For example, after the installation of the Backup Battery, the AC cord is disconnected or a power failure occurs, the
display will NOT remain lit, but the time and date settings will be temporarily maintained. The alarm, however, will not sound when the i199 is powered only
by the Backup Battery. To install Backup Battery, follow the instructions below:
1. Make sure the connection between the AC power supply and the unit is secure. This is important because during battery replacement it is possible for
all settings to be lost if the clock and alarm have already been set.
Download from Www.Somanuals.c-om9. -All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
GETTING STARTED
Installing the Backup Battery for Clock and Alarm Settings -Continued
2. Locate the battery compartment on the bottom of the unit and open.
3. Insert two (2) “AA” batteries, following the correct polarity (+/-) drawings inside the battery compartment. For longer battery life, alkaline batteries are
suggested. Please note that new and used batteries should not be mixed. Likewise, alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium)
batteries should not be used together.
4. Secure the battery compartment by closing the cover.
Important Notes on Batteries
To prevent battery leakage, which may result in bodily injury, property damage or damage to the unit, follow these instructions.
•
•
•
Install all batteries correctly according to the polarity (+/-) as marked on the unit.
Do not mix old and new batteries, carbon and alkaline, etc.
Remove batteries from the unit when the device will not be used for an extended period of time.
Please dispose the used batteries properly according to your local government regulations.
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
GETTING STARTED
Installing the Remote Control Battery
The remote control battery is included. Before operation, please install it to the battery compartment of remote
control.
1. Locate the battery compartment on the bottom of remote control and open.
2. Insert a “CR2025” 3V lithium battery. Make certain to follow the correct polarity, following the directions of the
corresponding symbols (+/-) as marked.
3. Secure the battery compartment by closing the cover.
Installing the AM Loop Antenna
For AM radio operation, locate the AM antenna jack on the back of the unit. Plug the AM loop antenna into the connector. To achieve the best reception
possible, a distance of 12” between the AM antenna, the unit and the iPod is recommended.
Installing the Dock Adapter
To ensure that your iPod will fit properly into the built-in universal dock, several detachable dock adapters for old iPod players
are included with this product. Please check the bottom of dock adapters to determine compatibility with your iPod.
1. Inserting the dock adapter
a. Choose a dock adapter that corresponds with the iPod you would like to dock. Using the correct dock adapter
ensures a proper fit.
b. Gently push the dock adapter down into the universal dock.
c. Carefully place your iPod into the universal dock. Please note that iPod must not be in a case or “Skin”.
2. Removing the dock adapter
a. Remove your iPod, grasp the dock adapter and carefully lift upwards.
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
GETTING STARTED
Location of Controls on the Main Unit
1. MULTI/DISPLAY
4. USB port
2. EJECT
3. iPod Dock
6. ID3/ST.
5. BluePin dock
8. SLEEP
7. Docking door OPEN
9. FUNCTION
10. VOLUME+/-(
13. WAKE TO
16. FR/Down
19. ALARM 1
22. TIME SET
)
11. Power ON/OFF/ Alarm off
14. FF/Up
12. SNOOZE/DIMMER
15. STOP
17. PLAY/PAUSE PRESET
20. ALARM 2
18. AM/FM
21. MEMORY
23. PLAY MODE
24. DOCKING DOOR
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
GETTING STARTED
Location of Controls on the Main Unit- continued
25. AC Power cord
26. FM Antenna
27. Aux In Socket
30. Backup Battery Compartment
28. AM Loop Antenna Socket
29. iPod AV Out Socket
Location of Controls on the Remote Control
1. POWER
2. ALBUM +/-
3. PLAY/PAUSE PRESET
4. FR /Down
6. MEMORY
8. FUNC
5.
VOLUME +/-
7. SLEEP
9. STOP/ AM/FM
11. PLAY mode
10. FF/Up
12. MUTE
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
GETTING STARTED
Location of Indications on the LCD Screen
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
Setting the Clock
1. To set the time, locate the TIME SET button. Press and hold the TIME SET button down until the Time display begins to flash. Set desired hour by
using ꢀ or ꢁ control button on the unit. Once desired hour is selected, press the TIME SET button once more to set Minutes. Use ꢀ or ꢁ control
button until the desired time is displayed. (NOTE: AM / PM indicator displays are located on the left side of the time.)
2. To secure the time setting and move to next setting, press the TIME SET button which will set the time and move you to date setting
3. To set the correct month, you may use ꢀ or ꢁ control button until the desired month is displayed or press the TIME SET button to secure month
setting and move to next setting.
4. Use same method to set desired day/year.
5. Once these steps are complete, Press the TIME SET button to secure time and date setting.
Setting the Alarm
This unit supports dual alarm feature.
1. Press and hold either ALARM 1 or the ALARM 2 button until the display begins to flash. Use ꢀ or ꢁ control button until the desired alarm time is
displayed, press ALARM 1 or ALARM 2 button to confirm and enter to next setting. (NOTE: AM/PM indicator displays are located on the left side of the
time.)
2. After setting the time, Use ꢀ or ꢁ control button and select the option for desired source for the alarm. Choose from iPod, USB, CD, AM / FM Radio or
buzzer. For AM/FM radio sources, you need to select the desired preset station.
3. Press ALARM 1 or ALARM 2 button to pre-set the volume level when the Alarm(s) is (are) activated. Use ꢀ or ꢁ control button to adjust the volume
level from 1 to 30. When the Alarm(s) is (are) activated, the volume will gradually rise from low to the pre-set setting.
4. Press the ALARM 1 or ALARM 2 buttons again to secure the setting and exit the alarm setting mode.
Notes: Make sure the alarm volume level set to desired level and the i199’s display has icon indicating alarm armed.
Using the Alarm Function
1. To preview the alarm setting, press Wake to Button and display will scroll through current alarm setting.
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
Using the Alarm Function –Continued
2. To activate or deactivate the alarm, press the ALARM 1 or ALARM 2 button once.
Notes: To preview alarm setting, the alarm must be activated before pressing Wake To Button.
3. To snooze, press the SNOOZE / DIMMER button on the i199, following the sounding of the alarm. The alarm will then shut off and will sound again in
approximately 9 minutes. You will have the opportunity to repeat this cycle many times during a 1 hour allotted alarm cycle.
4. To turn the alarm off, press the POWER button on the i199 (or the POWER button on the Remote Control). If all settings remain the same, the alarm
will turn on the following day at the same time. When the alarm is not turned off after it sounds, it will then play for approximately 60 minutes and turns
off automatically. This cycle will repeat every 24 hours unless the controls are changed.
5. To prevent the alarm from coming on daily, press the ALARM 1 or ALARM 2 buttons and set to off. The Alarm Icon will disappear.
Notes on Alarm Function:
•
•
Set your iPod to the repeat mode if you’ve selected Wake to iPod, and your iPod has less than one hour of songs.
If you have selected the Wake To iPod, CD or USB setting, yet no iPod, CD or USB is present at the alarm time, the i199 will automatically switch to
the BUZZER mode.
•
•
In the event of a power outage or if AC power is disconnected, when the i199 is powered by the Backup Battery, the alarm will NOT sound and time
and date will not be displayed. Time and date settings, however, will be temporarily saved.
All alarm functions will be activated in standby mode, if you already turned on the i199, alarm function will be deactivated.
Adjusting the Brightness of LCD Screen
To adjust the brightness of the LCD screen, press the SNOOZE / DIMMER button on the unit during normal or standby mode. Each press will change the
brightness level of the LCD screen.
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
Setting the Sleep Time
1. To enter sleep mode, press the SLEEP button while the i199 is on. The unit will automatically turn off after the selected time. The sleep mode also has
a feature called the “Gentle Sleep”, which gradually decreases the volume.
2. To adjust the sleep time, press the SLEEP button again and choose from 120, 90, 60, 30, and 15 minutes.
3. To view the sleep time, wait until the display returns to the current time and press the SLEEP button once. It will display the sleep time remaining. Press
again to change the sleep time to the next lowest increment.
4. To stop listening at any time, press the POWER button or the POWER button on the Remote Control.
5. To cancel the sleep setting, continuously press the SLEEP button until SLEEP icon disappears on LCD.
Listening to Your Favorite Radio Stations
For the best FM radio clarity, fully extend the pig-tail wire antenna, located on the rear of the i199. It is important not to alter, obstruct or attach other
antennas to this wire antenna. To achieve the best AM reception, a distance of 12” between the AM antenna, the unit and iPod is recommended. Rotate the
AM loop antenna to have the better reception.
1. To turn the radio on, press the FUNC button on the i199 (or on the Remote Control). Once on, the radio frequency
will appear in the lower right corner of the display.
2. To select AM or FM, press the FUNC button on the i199 or STOP/AM/FM on the Remote Control.
3. To tune in to a desired station, use ꢀ or ꢁ buttons on the i199 or use ꢀ or ꢁ buttons on the Remote Control.
4. To scan the next clear station, press and hold ꢀ or ꢁ buttons on the i199 or Remote Control for 4 seconds.
5. To adjust the volume, use
remote control.
(VOLUME+) and
(VOLUME-) on the i199 or
and
buttons on the
6. To power OFF, press the POWER button (or the POWER button on the Remote Control).
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
Programming Preset Stations
1. Select AM or FM using AM/FM button on the i199 unit.
2. Tune to the desired station using ꢀ or ꢁ buttons on the i199 unit or remote control.
3. Select between Stereo or Mono by pressing ID3/ST button. (FM ONLY)
4. Press MEMORY button to start programming. You will notice flashing preset number next to station you’ve just selected.
5. Press MEMORY button again to store current flash preset station number (When MEMORY is pressed again the preset number will increase by one).
6. To assign preset station number use PRESET button and press MEMORY button again to store.
Note: Please note that FM has 30 presets and AM have 10 presets.
7. Display with read “STORED”, which indicates station setting has been saved and stored in the memory.
8. Repeat above steps to store other presets into the memory.
Listening to Your Favorite Songs on Your iPod
1. To listen to music, make sure that your iPod is in play mode.
NOTE: If the i199 fails to play or you do not hear any sound coming out from the unit, make sure your iPod is securely docked in the Built-In Universal
dock and press the PLAY/PAUSE button on the i199 or on the Remote Control for music play to begin.
2. To play music when your iPod is already in the dock and in the standby mode, press the PLAY/PAUSE button on the i199 or the PLAY/PAUSE button
on the Remote Control. When your iPod is in the play mode, an iPod icon will appear on the LCD screen of the i199.
3. To pause music, press the PLAY/PAUSE button during the play mode. To resume playback, press it again.
4. To adjust the volume, either use
(VOLUME+) and
(VOLUME-) on the i199, or use the
(VOLUME+) and
(VOLUME-) buttons on the
remote.
5. To go to the Previous or Next track, use ꢀ or ꢁ button on the i199 or on the remote control. To search the current track using high speed rewind or
forward, press and hold ꢀ or ꢁ buttons while track is playing.
6. To power the unit off, press the POWER OFF button on the i199 or on the remote. Your iPod will continue to charge when left in the universal dock.
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
Listening to CDs/MP3-CDs
The i199 features a slide-in mechanism for easy loading and unloading
1. Press FUNC. button to select the CD mode.
2. Insert the MP3-CD/CD disc in the loading bay.
•
FOR CD
After a few seconds, the total playing time and number of tracks appear on the display.
FOR MP3-CD
•
After a few seconds, the total number tracks, album of MP3 and STOP appear on the display.
Note: Press EJECT button next to CD load bay, the MP3-CD/CD disc will be loaded or unloaded.
Playing the Entire Disc
1. Press Play / Pause (PRESET) button on the unit.
• Play starts with the first track.
• The display shows the current track number and its elapsed playing time.
• When all tracks have played, the MP3-CD/CD will stop and return to initial display.
2. To stop play, press STOP button.
3. To pause play, press Play / Pause (PRESET) button.
4. To resume play, press Play / Pause (PRESET) button again.
Selecting a Different Track during Play
1. Press ꢀ or ꢁ buttons until the required track number appears in the display.
2. MP3-CD mode only: Press ALBUM +/- button (on remote only) once or more to find your desired album.
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
Selecting a Different Track During Play -Continued
3. Press and hold ꢀ or ꢁ buttons to search through the track.
Programming Tracks
Up to 32 tracks can be stored in the memory.
1. Load an MP3-CD/CD as described previously.
2. Press MEMORY key to start programming.
3. Press ꢀ or ꢁ buttons to locate a particular track or album/track (MP3-CD).
4. Press MEMORY key to store it in the memory.
5. Continue this process until you have selected all the tracks you desire.
Reviewing the Program
Press MEMORY key to review of the tracks currently programmed.
1. The tracks will be displayed on the LCD.
2. Press MEMORY key again to scroll through the program.
Playing a Program
1. Press Play / Pause (PRESET) button.
2. Play starts with the first track of the program.
3. When all tracks have been played, the MP3-CD/CD player stops.
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
Clearing Program Tracks
Press MEMORY button, the LCD will display the first programmed tracks, pressing the STOP button will erase all programmed tracks.
REPEAT or INTRO or RANDOM PLAY (For CD)
Press PLAY MODE button until the display indicates one of the following:
• To repeat one track select “REPEAT 1”
• To repeat all track select “ REPEAT ALL”
• To listen to intro select “INTRO”
• To play randomly select “RANDOM”
• To cancel the play mode, press PLAY MODE button until all play mode display disappears.
REPEAT or INTRO or RANDOM PLAY (For MP3)
Press PLAY MODE button until the display indicates one of the following:
• To repeat one track select “REPEAT 1”
• To repeat folders select “REPEAT ALBUM”
• To repeat all folder/ track select “ REPEAT ALL”
• To listen to intro select “INTRO”
• To play randomly select “RANDOM”
• To cancel the play mode, press PLAY MODE button until all play mode display disappears.
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
Listening to your favorite music on your USB Storage device
The i199’s USB connector allows you to listen to stored MP3 and Wma files on your USB Storage device
1. Open the DOCKING DOOR.
2. Insert the USB device with MP3 or WMA files in the USB Socket.
3. Press FUNC. button and select USB mode, the total number tracks, albums of MP3 and STOP
appear on the display.
4. The i199 will search for the recognized files and you can browse using ꢀ or ꢁ buttons.
5. To play, press Play / Pause (PRESET) button.
6. To interrupt play, press Play / Pause (PRESET) button.
7. To resume play, press Play / Pause (PRESET) button again.
8. To STOP play, press STOP button.
Using AV-out port to watch Videos from your iPod on an External Monitor or TV
The i199 has an AV port to send video signal of your video iPod (5G, 5.5G) to the external display devices, such as TV or a monitor.
To use this function, please follow the instructions below:
1. Connect the provided AV cable into the iPod AV-out port (3.5mm) on the rear of the i199. Then connect the RCA
plug side of the AV cable to the AV input jacks of the external display device. (Please refer to illustration on the left)
2. Turn on the external display device. Change the mode of the external display device to the AV mode if
necessary.(Note: Please refer to the owner’s manual of external devices for AV Mode)
3. Place your iPod in the built-in universal dock.
4. Play the video on your iPod. (Please note that the “TV Out” setting of your iPod must be set to “On” in order to see
the iPod video contents on your TV via the i199. Please refer to the illustration on the following page).
Note: This function is usable for both i199 power on and off modes.
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
Using AV out port to watch Video on your iPod from an External Monitor or TV – Continued
Note: The line output is not affected by the volume setting on the i199. Please use the volume control of the external device to increase or decrease the
volume level.
*IMPORTANT: When Using TV Out, please make sure your iPod Video setting is set to “TV Out-ON”
Please follow the illustration below on your video iPod to change the setting:
n On the menu screen of your iPod, select
the “Videos” option.
o On the next menu screen, select the “Video p On the next menu screen, select the “TV
Settings” option. Out” option and set it on.
Note: When watching video content using AV out port and TV Out is set to ON on your iPod, your iPod and external device will not simultaneously display
the pictures.
TV Out Set to OFF: Video displays only on your iPod
TV Out Set to ON: Video displays only on the external device.
- 23 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
Listening to Other Audio Devices using line-in port
You can still listen to the first, second, and third generations of iPod, or any other audio players other then iPod, with the i199 by simply using the AUX-IN
port, located on the rear of the i199.
1. Insert the plug of the audio patch cord (Not Included) into the HEADPHONE or LINE-OUT jack on your audio device, and then insert the other end of
the patch cord with 3.5mm Stereo plug into the AUX-IN jack, located on the rear of the i199.
2. For AUX mode, press the FUNC button on the i199, or on the Remote Control, until the AUX icon appears on the i199’s display.
3. It is now safe to turn ON your device and enjoy the music.
4. Use the VOLUME button on the i199, or the
(Volume +) and
(Volume –) buttons on the Remote Control to adjust the decibel level. You
may also need to adjust the audio device volume.
AUX-IN
Charging Your iPod
Your iPod will always be in charge mode when left in the built-in Universal Dock until it is fully charged. Your iPod will also be in charge mode when not in
use if your iPod is left in the Built-in Universal Dock. Your iPod will not charge when the unit is NOT docked in the built-in Universal Dock.
Note: Older generation (Including 3G) iPod not supported, only newer 30pin connectors are supported by i199’s Universal Dock. Please see compatibility list
for the i199.
- 24 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
BluePinTM Setup and operating Instructions.
Overview:
Pairing Button
TX/RX Switch
Status Indicator
*Status Indicator mode
•
•
•
•
•
No light: Not in operation
Blue Light slow flashing: Standby Mode
Blue Light fast flashing : search Mode
Blue & Red Light Flashing: Pairing Mode
Solid Blue Light: Normal Operation Mode
*BluePinTM Device Password: “0000”
*TX: Transmitting sound to other devices such as Stereo Headset with Bluetooth technology with Bluetooth stereo Profile (A2DP)
*RX: Receiving sound from other media players such as MP3 Cell Phones with Bluetooth Stereo Profile (A2DP) or Other Media Players with Bluetooth
Stereo Profile (A2DP)
•
Bluetooth Mode: When BluePinTM is connected to i199 you will see a flashing Bluetooth icon on the display.
Bluetooth Mode Indicator
NOTE: Certain devices with Bluetooth technology might not be compatible with the BluePinTM, please check with your dealer for compatibility. The best
product for this operation is iLuv Stereo Headsets with Bluetooth technology which are fully compatible with the BluePinTM
.
- 25 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
1. Plug the BluePinTM unit securely into the i199’s BluePinTM port. When BluePinTM is plugged in, BluePinTM status below :
TX selection: Status indicator will slow flash (standby mode) RX selection: Status indicator will fast flash (search mode)
2. When the BluePinTM is plugged in to the i199, the main display will show flashing Bluetooth logo, after successfully connected to a Bluetooth
device, display will show “TX CONN” or RX CONN” for a few seconds and Bluetooth icon lights steadily, i199 will display “BT--RX” mode when
BluePinTM is set to “RX” mode.
Display indicating
the Bluetooth mode
i199 Display will indicates “BT- -RX”
function mode when BluePinTM set
to “RX” mode
3. Once the BluePinTM is securely plugged in to the i199, press the pairing button to start pairing with other devices. You will notice that blue and red
lights will flash on the unit indicating the device is ready to be paired with other devices with Bluetooth technology.
In pairing mode red & blue light will
flash rapidly
- 26 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
4. You are now ready to pair with other devices with Bluetooth technology.
5. Before pairing make sure to set the BluePinTM as TX or RX depending on the purpose.
Note: TX is for transmitting signals to other devices like stereo headsets with Bluetooth technology with A2DP Profile. RX is for receiving signals
from other sources like a cell phone with Bluetooth stereo profile (A2DP) or Media Players equipped with Bluetooth Stereo Profile (A2DP).
6.
The switch for TX and RX is located on the left side of the BluePinTM unit.
TX/RX Switch
Example (RX Mode): If you have a MP3 cell phone with Bluetooth Stereo Profile (A2DP) could transmit the music on your cell phone to your i199
w/ BluePinTM to enjoy the music on the i199 (For this operation the BluePinTM should be set to RX for receiving).
- 27 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
Example (TX Mode): If you have a Stereo Headset with Bluetooth technology (Mono will not work, only stereo headphone with A2DP Bluetooth
profile will work), you can set the BluePinTM to Transmit (TX) the music that is currently playing on i199 to the headphone.
NOTE: Certain Headsets with Bluetooth technology are not compatible with the BluePinTM, please check with your dealer for compatibility. The
best product for this operation is iLuv Stereo Headset with Bluetooth technology, which is fully compatible with BluePinTM. Devices with Bluetooth
technology you are trying to pair MUST support A2DP Profile.
7. To pair with cell phones, PDA, or other devices with the BluePinTM (RX Mode):
•
•
•
•
•
•
•
First connect the BluePinTM to i199’s BluePinTM port. The BluePinTM blue light will fast flash of search mode ready.
Push and hold the pairing button until LED displays blue and red light flashing.
From your cell phone or other devices, go to Bluetooth setup in the devices menu. Depending on the devices menu will differ.
Does a search for devices, when initiated your device will look for any devices with Bluetooth technology in the area.
When the search is done you will see a device named “RX-i110”. Select the device and your device will prompt for password.
The default password for our BluePinTM unit is “0000”, enter password and your device will let you know if pairing was successful.
Once connected, you will be able to play the songs from MP3 cell phones or other devices with Bluetooth technology and hear it from
our i199 unit.
•
You can use the PLAY/PAUSE, PREV, NEXT buttons of i199 to remote control the MP3 cell phones or other devices that support
AVRCP profile.
Note: Depending on the device, these functions might be disabled due to differences in software.
8. To pair with Bluetooth Stereo Headset with Bluetooth Stereo Profile (A2DP)(TX Mode):
•
•
Set BluePinTM’s switch to TX for transmitting to the Headset.
Place the BluePinTM in the i199’s BluePinTM port, push and hold pairing button until you get red and blue flashing light.
- 28 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
OPERATIONAL INSTRUCTIONS
•
•
Push pairing button on the headset with Bluetooth technology until red and blue lights flash.
When both units are no longer flashing red and blue lights, and a blue light flashes steadily you are now connected and can send music
from i199 to Headset with Bluetooth wireless technology. The speakers of the i199 will be muted after it connected to a headset with
Bluetooth technology, you can press the MUTE button or VOLUME buttons to release mute. After turning off the headset with Bluetooth
technology, or headset is out of transmitting range, the speakers mute will be released.
•
•
After paired with a headset, the pairing information will be stored in both devices even if one or both of them has been turned off. The
next time both devices are turned on, they will not need to be paired again, simply follow one of following methods to connect them.
—
After turning on the headset, it will connect BluePinTM automatically. If the headset doesn’t have automatic Bluetooth
connection function, just press PLAY/PAUSE button to connect BluePinTM
.
—
—
Or press PAIRING button of BluePinTM to connect headset with Bluetooth technology.
If headset is in standby mode, press the PLAY/PAUSE button of the headset to connect BluePinTM
.
You can control the i199 remotely by using function buttons of headset with Bluetooth wireless technology, details as follows:
BUTTONS
iPod
CD/ MP3 CD
USB
RADIO
PLAY/PAUSE
STOP
Play/ Pause
Stop
Play/ Pause
Stop playback
Previous song
Next song
Play/ Pause
Stop playback
Previous song
Next song
Preset station select
AM/ FM band select
Auto search- Down
Auto search- Up
PREV
Previous song
Next song
NEXT
Noted: Depending on the headset, these functions might be disabled due to differences in software.
- 29 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
MAINTENANCE & TROUBLESHOOTING GUIDE
Maintenance
•
•
Place the unit on a leveled surface away from sources of direct sunlight or excessive heat.
When placing the unit on a natural wood and lacquered finish, a cloth or other protective material should be placed between it and the furniture to avoid
any damage to the unit and the furniture.
•
Clean the unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzine, thinner or similar materials can
damage the surface of the unit.
Troubleshooting
•
The stereo speaker system (i199) does not turn on.
o
o
The AC plug may not be connected properly. Check the connection.
The wall outlet may not function. Try another outlet.
•
Your iPod does not fit into the built-in universal dock.
o
o
The installed dock adapter is not the correct one. Check whether a correct dock adapter is installed.
There might be some obstructions on the dock. Check whether there are any obstructions on the connector and on the dock. If everything is
secured, place your iPod back into the dock.
•
It does not recognize your iPod when docked.
o
o
o
o
Your iPod may not be properly docked. Take your iPod out of the dock, and remove any obstructions on the connector from the dock and on
your iPod. Place your iPod back into the dock.
Your iPod is frozen or locked up. Check whether your iPod operates correctly before placing it back into the dock. Please refer to the owner’s
instruction manual of your iPod.
The software of your iPod is outdated. Upgrade the software on your iPod. For the details on how to upgrade the software on your iPod,
You are using the first, second, or third generation iPod. The i199 does not recognize first, second and third generation iPod. Use the line-in
jack for the first, second, and third generation of iPod.
- 30 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
MAINTENANCE & TROUBLESHOOTING GUIDE
Troubleshooting – Continued
•
Your iPod is not charged even though it is in the dock.
o
o
o
Your iPod might not be properly docked. Take your iPod out of the dock, and remove any obstructions on the connector from the dock and on
your iPod. Place your iPod back into the dock.
Your iPod is frozen or locked up. Check whether your iPod operates correctly before placing it back into the dock. Please refer to the owner’s
instruction manual of your iPod.
You are using the first, second, or third generation of iPod. First, second, and third generation of iPod is only charged with the FireWire
connection. The FireWire connection is not supported by the i199.
•
There is no sound on the external speakers when connected by the audio patch cable.
o
o
o
i199 supports iPod audio and video output only.
The connected speakers lack a power source. Check if the external speakers are powered properly.
You are using passive speakers, which have no built-in amplifier. The signal from iPod AV-OUT jack needs to be amplified. Use the active
speakers, which have a built-in amplifier.
•
•
It does not find any AM radio stations, or there is a lot of static on a radio station.
o
o
The AM loop antenna is not connected to the i199. Connect the AM loop antenna to the jack on the back of the i199.
The i199 is installed where the reception is bad. Move the AM loop antenna around keeping it away from the main unit for the best reception.
When playing music, the sound gets distorted.
o
o
The volume level on the connected device or the i199 is set too high. Decrease the volume until the distortion has disappeared.
The source sound is distorted. If the original sound source (MP3) on your iPod is poor quality, the distortion and noises are easily noticed with
high-power speakers. Try a different audio source like a music CD to test.
•
•
The remote control does not operate properly.
o
o
The installed battery is weak. Replace with a new battery.
It is not aimed to the i199 or too far away from it. Move within 20 feet of the unit and point the remote control toward the i199.
Sudden drop of volume or hear static or distortion when using devices with Bluetooth technology with BluePinTM
Please check your battery level and charge if necessary.
o
- 31 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
MAINTENANCE & TROUBLESHOOTING GUIDE
Troubleshooting – Continued
o
o
o
Make sure you are not too far away from the unit.
Make sure you are free from any interfering devices such as walls and any other wireless devices.
Check if the BluePinTM unit is securely connected to the i199’s BluePinTM Port.
•
Pairing with other devices with Bluetooth technology with BluePinTM is not working.
o
o
o
o
o
o
o
Make sure TX/RX switch is set correctly on the BluePinTM.
Be sure to check your devices manual to see if A2DP Bluetooth Profile is supported.
Make sure the devices are not too far away from each other.
Make sure to put the correct password (The default password for BluePinTM is “0000”).
Check with your devices manual if the device supports other Bluetooth products.
Make sure both devices are in pairing mode to accept connections from each other.
Make sure the Bluetooth device you are using is Bluetooth Version 1.2 or higher for stable connectivity. (Some of the V1.1 devices might not
be fully compatible with BluePinTM. Make sure to check your Bluetooth devices manual for compatibility issues).
•
Cannot pair with stereo headset with Bluetooth wireless technology made by other manufacturers.
o
This could happen if the device has its own security method, or unique password other then “0000”. Please check with the manufacturer for
compatibility issues. For full compatibility we recommend an iLuv Stereo Headset with Bluetooth wireless technology.
Make sure headset supports A2DP Bluetooth Stereo Profile.
o
o
o
Make sure the device is fully charged and you are not too far away from the BluePinTM. unit.
Make sure you are not using mono headset to pair. (This will not work since mono headset uses different Bluetooth profile. If profiles do not
match with the devices you are connecting to, pairing will fail. Please check your device manual, or check with manufacturer to see if device
has matching A2DP Bluetooth Stereo Profile)
•
•
There seems to be noticeable delay between the devices with Bluetooth wireless technology and i199.
This is normal when using devices using Bluetooth wireless technology.
Remote functions like play/pause skip up, skip down does not work
o
o
Depending on the device these functions might be disabled due to differences in software.
o
Please refer to owner’s manual of the device you are using.
- 32 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
SPECIFICATIONS
General
•
Power Requirement
o
Main Unit: AC 120V/60Hz (USA) 230V50Hz (EURO)
•
•
Output Power: 8W (RMS) into 8 ohm
Power consumption: 40W
Radio
•
Frequency Ranges: MW 522 - 1620kHz / FM 87.5 - 108MHz (EURO); AM 530 – 1710kHZ / FM 87.5 – 108MHz (USA)
Compact Disc
•
•
•
•
Frequency Response (-6dB): 60 - 15,000Hz
Signal-to-noise ratio: 40dB
Harmonic Distortion: 1%
Channel Separation: 40dB
BluePinTM Audio Transmitter / Receiver
o
o
o
o
o
o
o
Bluetooth Core: Bluetooth V1.2 compliant
Bluetooth Profile: A2DP, AVRCP
Operating Frequency: 2.4 ~ 2.4835GHz
Security Features: 128-bit Encryption
Transmitting Rate: 721Kbps (Max)
Wireless Technology: FHSS
Communication Distance: Up to 33ft (10m)
* Specifications and features are subject to change without notice.
- 33 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Audio System for Your iPod
V11M11_IM_EN_01122007
- 34 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TEL: 516-626-7188
FAX: 516-626-7105
e-mail: [email protected]
iLuv is a trademark of jWIN Electronics Corp. iPod is a trademark of Apple Computer Inc. iPod is not included in this package. Features and specifications
are subject to change without prior notification. BluePin is a trademark of jWIN Electronics Corp. The Bluetooth word mark and logos are owned by Bluetooth
SIG, Inc. and any use of such marks by jWIN Electronics Corp. is under license. All other logos and brands are property of their respective owners.
© 2007 jWIN Electronics Corp. All rights reserved. No portion of this printed material or product enclosed herewith including design, shape and graphics,
may be reproduced or transmitted in any form without the expressed written consent of jWIN Electronics Corp. by any means, electronic or mechanical,
including photocopying, recording or with an information storage and retrieval system. Any unauthorized distribution or reproduction of this printed material
or product, or any portion there of, will be prosecuted to the fullest possible extent of the law.
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|