Icom Two Way Radio iF25 S User Manual

INSTRUCTION MANUAL

VHF TRANSCEIVER

iF15/S

UHF TRANSCEIVER

iF25/S

Download from Www.Somanuals.com. All Manuals Search And Download.

FOREWORD

PRECAUTION

READ ALL INSTRUCTIONS carefully and completely before

RWARNING! NEVER hold the transceiver so that the antenna

is very close to, or touching exposed parts of the body, especially

the face or eyes, while transmitting. The transceiver will perform

best if the microphone is 5 to 10 cm away from the lips and the

transceiver is vertical.

using the transceiver.

SAVE THIS INSTRUCTION MANUAL— This instruction

manual contains important operating instructions for the IC-F15/

F15S ^{VHF TRANSCEIVER}and IC-F25/F25S UHF TRANSCEIVER.

RWARNING! NEVER operate the transceiver with a headset

or other audio accessories at high volume levels.

CAUTION! NEVER short the terminals of the battery pack.

EXPLICIT DEFINITIONS

NEVER connect the transceiver to a power source other than the

BP-230, BP-231 or BP-232. Such a connection will ruin the trans-

ceiver.

DO NOT push the PTT when not actually desiring to transmit.

AVOID using or placing the transceiver in direct sunlight or in

areas with temperatures below –25°C or above +55°C.

WORD

RWARNING

CAUTION

NOTE

DEFINITION

Personal injury, fire hazard or electric shock

may occur.

Equipment damage may occur.

DO NOT modify the transceiver for any reason.

If disregarded, inconvenience only. No risk

of personal injury, fire or electric shock.

MAKE SURE the ﬂexible antenna and battery pack are securely

attached to the transceiver, and that the antenna and battery pack

are dry before attachment. Exposing the inside of the transceiver

to water will result in serious damage to the transceiver.

The use of non-Icom battery packs/chargers may impair transceiver

performance and invalidate the warranty.

OPERATING NOTES

• When transmitting with a portable radio, hold the radio in a vertical

position with its microphone 5 to 10 centimeters away from your

mouth. Keep the antenna at least 2.5 centimeters from your head

and body.

• If you wear a portable two-way radio on your body, ensure that the

antenna is at least 2.5 centimeters from your body when transmit-

ting.

Icom, Icom Inc. and the

logo are registered trademarks of Icom Incorpo-

rated (Japan) in the United States, the United Kingdom, Germany, France, Spain,

Russia and/or other countries.

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESSORIES

I Supplied accessories

TABLE OF CONTENTS

The following accessories are supplied:

Qty.

FOREWORD ……………………………………………………………… i

EXPLICIT DEFINITIONS ………………………………………………… i

OPERATING NOTES……………………………………………………… i

PRECAUTION …………………………………………………………… ii

TABLE OF CONTENTS ………………………………………………… iii

1 ACCESSORIES……………………………………………………… 1–5

‘ Supplied accessories………………………………………………… 1

‘ Accessory attachments……………………………………………… 2

2 PANEL DESCRIPTION …………………………………………… 6–11

‘ Front, top and side panels ………………………………………… 6

‘ LED indicator ………………………………………………………… 8

‘ Programmable function keys ……………………………………… 9

3 CONVENTIONAL OPERATION………………………………… 12–18

‘ Turning power ON ………………………………………………… 12

‘ Channel selection ………………………………………………… 12

‘ Call procedure ……………………………………………………… 13

‘ Receiving and transmitting ……………………………………… 14

‘ Scrambler function ………………………………………………… 16

‘ Setting the squelch level ………………………………………… 16

‘ Man Down Emergency Call ……………………………………… 17

4 OPTIONAL UNIT INSTALLATION……………………………… 18–19

‘ Optional unit installation …………………………………………… 18

‘ Scrambler unit installation ………………………………………… 19

5 BATTERY CHARGING ………………………………………… 20–25

‘ Battery charging …………………………………………………… 20

‘ Caution ……………………………………………………………… 21

‘ Optional battery chargers ………………………………………… 22

6 SWIVEL BELT CLIP……………………………………………… 26–29

‘ MB-93 contents …………………………………………………… 26

‘ To attach …………………………………………………………… 26

‘ To detach …………………………………………………………… 28

7 OPTIONS ………………………………………………………… 30–31

8 DOC………………………………………………………………… 32–33

q Flexible antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

w Battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

e Belt clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

r Unit cover (double-sided tape)* . . . . . . . . . . . . . . . . . . . . . . . .1

t Jack cover (with screws) . . . . . . . . . . . . . . . . . . . . . . . . . . .1 set

* Use the unit cover as a spare. Ask your dealer for details.

Download from Www.Somanuals.com. All Manuals Search And Download.

iii

ACCESSORIES

I Accessory attachments

DFlexible antenna

ï Battery pack

Connect the supplied flexible an-

tenna to the antenna connector.

To attach the battery pack:

Slide the battery pack on the back of the transceiver in the direc-

tion of the arrow (q), then lock it with the battery release button.

• Slide the battery pack until the battery release button makes a ‘click’

sound.

To release the battery pack:

Push the battery release button in the direction of the arrow (w) as

shown below. The battery pack is then released.

CAUTION:

• NEVER HOLD by the antenna

when carrying the transceiver.

• Transmitting without an antenna

may damage the transceiver.

NEVER release or attach the battery pack when the transceiver

is wet or soiled. This may result in water or dust getting into the

transceiver/battery pack and may result in the transceiver being

damaged.

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESSORIES

ï Jack cover

DBelt clip

Attach the jack cover when the optional speaker-microphone is not

used.

To attach the belt clip:

q Release the battery pack if it is attached.

To attach the jack cover:

To detach the jack cover:

w Slide the belt clip in the direction of the arrow until the belt clip is

q Attach the jack cover to the q Unscrew the screws with a

locked and makes a ‘click’ sound.

[SP MIC] connector.

w Tighten the screws.

phillips screwdriver.

w Detach the jack cover for the

speaker-microphone connec-

tion.

To detach the belt clip:

q Release the battery pack if it is attached.

w Pinch the clip (q), and slide the belt clip in the direction of the

arrow (w).

Download from Www.Somanuals.com. All Manuals Search And Download.

2 ^{PANEL DESCRIPTION}

PANEL DESCRIPTION

I Front, top and side panels

e LED INDICATOR (p. 8)

IC-F15S/F25S

IC-F15/F25

➥ Lights red while transmitting.

➥ Lights green while receiving a signal, or when the squelch is

open.

➥ Lights/blinks orange when the matched 2/5-tone code is re-

ceived, according to the pre-programming.

r SPEAKER-MICROPHONE CONNECTOR [SP MIC]

Connects the optional speaker-microphone. (p. 31)

[SP MIC] jack cover

Speaker

NOTE: Attach the [SP MIC] jack

cover when the optional speak-

er-microphone is not used. (p. 4)

Microphone

t DEALER-PROGRAMMABLE KEY [Lower]

The desired function can be assigned by your dealer. (p. 9)

y PTT SWITCH [PTT]

Push and hold to transmit; release to receive.

u DEALER-PROGRAMMABLE KEY [Upper]

The desired function can be assigned by your dealer. (p. 9)

i ANTENNA CONNECTOR

Connects the supplied antenna.

DProgrammable key reference

q CHANNEL SW/SELECTOR

• IC-F15S/F25S: Toggle the channel switch to select the pre-pro-

grammed channel 1 or 2.

• IC-F15/F25 : Rotate the channel selector to select the pre-

programmed memory channels.

Upper

Lower

w VOLUME CONTROL [VOL]

Rotate to turn the power ON/OFF and adjust the audio level.

Download from Www.Somanuals.com. All Manuals Search And Download.

PANEL DESCRIPTION

‘

LED indicator

Programmable function keys

The LED indicator indicates several informa-

tion as follows;

The following functions can be assigned to [Upper] and [Lower]

programmable function keys.

(Ref.; R=Red, G=Green, O=Orange)

Consult your Icom dealer or system operator for details concerning

your transceivers programming.

If the programmable function names are bracketed in the following

explanations, the speciﬁc key used to activate the function depends

on programming.

• TX: Turns Red while transmitting a signal.

SCAN A KEY

• RX: Turns Green while receiving a signal.

➥ This key’s operation depends on the Power ON Scan setting.

When the power ON scan function is turned OFF;

Push to start and cancel scanning operation. In case of trans-

mission during scan, cancels scanning.

• Call LED (ON): When receiving a matched 2/5-tone.

When the power ON scan function is turned ON;

Push to pause scanning. Scanning resumes after passing a

specified time period. In case of transmission during scan,

pauses scanning. Scanning resumes after passing a speciﬁed

time period.

O O

• Call LED (Blink): When receiving a matched 2/5-tone.

• Fast/Slow scan: Blinks while Fast/Slow scan is activated.

SCAN B KEY

Push to start and cancel scanning operation. In case of transmis-

sion during scan, pauses scanning. Scanning resumes after pass-

ing a speciﬁed time period.

• Low BATT1: You should charge the battery. (blinks slowly)

• Low BATT2: You must charge the battery. (blinks fast)

PRIORITY CHANNEL KEYS

➥ Push to select the Priority A or Priority B channel.

➥ Push and hold [Prio A (Rewrite)] to rewrite the Prio A channel.

• TX low BATT2: Low BATT2 was detected during TX mode.

MR-CH 1/2/3/4 KEYS

Push to select a memory channels 1 to 4 directly.

NOTE: The memory channels 3 and 4 are available for IC-

F15S/F25S when [MR-CH 3] and [MR-CH 4] keys are assigned.

• CH err: Non-programmed channel is selected.

R O R O R O R O R O R O R O R O

Download from Www.Somanuals.com. All Manuals Search And Download.

PANEL DESCRIPTION

MONITOR KEY

DTMF AUTODIAL KEY

➥ Mute and release the CTCSS (DTCS) or 2-tone squelch mute.

Open any squelch/deactivate any mute while pushing this key.

(LMR operation only)

➥ Activates one of (or two of) the following functions on each chan-

nel independently: (PMR operation only)

Push to transmit the programmed DTMF code.

CALL KEYS

Push to transmit a 2/5-tone code.

• Call transmission is necessary before you call another station de-

pending on your signalling system.

• [Call A] and/or [Call B] keys may be available when your system em-

ploys selective ‘Individual/Group’ calls. Ask your dealer which call is

assigned to each key.

• Push and hold to un-mute the channel (audio is emitted; ‘Audible’

condition).

• Push to mute the channel (sets to ‘Inaudible’ only).

• Push to un-mute the channel (sets to ‘Audible’ only).

• Push after the communication is ﬁnished to send a ‘reset code’.

NOTE: The un-mute condition (‘Audible’ condition) may auto-

matically return to the mute condition (‘Inaudible‘ condition)

after a speciﬁed period.

EMERGENCY KEYS

➥ Push and hold to transmit an emergency call.

➥ When [Emergency Single (Silent)] or [Emergency Repeat

(Silent)] is pushed, an emergency call is transmitted without a

beep emission.

LOCK KEY

• If you want to cancel the emergency call, push (or push and hold)

the key again before transmitting the call.

• The emergency call is transmitted one time only or repeatedly until

receiving a control code depending on the pre-setting.

Push and hold to electronically lock all programmable keys except

the following:

[Call] (incl. Call A and Call B), [Moni(Audi)] and [Emergency] keys.

OUTPUT POWER SELECTION KEY

Select the transmit output power temporarily or permanently, de-

pending on the pre-setting.

• Ask your dealer for the output power level for each selection.

VOICE SCRAMBLER FUNCTION KEYS

➥ Push to turn the voice scrambler function OFF.

➥ Push and hold to turn the voice scrambler function ON.

OPT OUT KEYS

➥ Push to inactivate the connected output signal level.

➥ Push and hold to activate the connected output signal level.

TALK AROUND KEY

➥ Push to turn the talk around function OFF.

➥ Push and hold to turn the talk around function ON.

• The talk around function equalizes the transmit frequency to the re-

ceive frequency for transceiver-to-transceiver communication.

SIREN KEY

Push to emit a siren. This function can be used for situations other

than an emergency alert such as a security alarm for example.

WIDE/NARROW KEY

➥ Push to select the IF bandwidth to wide.

• The wide passband width can be selected from 25.0 or 20.0 kHz

using the CS-F14 CLONING SOFTWARE (PMR operation only.) Ask

your dealer for details.

➥ Push and hold to select the IF bandwidth to narrow.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENTIONAL OPERATION

I Turning power ON

CONVENTIONAL OPERATION

I Call procedure

➥ Rotate [VOL] to turn power ON.

When your system employs tone signalling (excluding CTCSS and

DTCS), the call procedure may be necessary prior to voice trans-

mission. The tone signalling employed may be a selective calling

system which allows you to call speciﬁc station(s) only and prevent

unwanted stations from contacting you.

[VOL]

q Select the desired TX code channel or 2/5-tone code according

to your System Operator’s instructions.

• This may not be necessary depending on programming.

w Push the call key (assigned to one of the dealer programmable

keys.) (p. 11)

e After transmitting a 2/5-tone code, the remainder of your com-

munication can be carried out in the normal fashion.

I Channel selection

IC-F15S/F25S:

Toggle [CHANNEL SWITCH] to select

the channel 1 or 2, or, push one of [MR-

CH 1] to [MR-CH 4] key to select a chan-

nel directly.

Selective calling

Non-selective calling

• The memory channels 3 and 4 are avail-

able when [MR-CH 3] and [MR-CH 4]

keys are assigned.

[CHANNEL SWITCH]

IC-F15/F25:

[CHANNEL

SELECTOR]

Rotate [CHANNEL SELECTOR] to se-

lect the desired operating channel, in se-

quence; or, push one of [MR-CH 1] to

[MR-CH 4] key to select a channel di-

rectly.

AUTOMATIC SCAN TYPE:

Channel setting is not necessary for this type. When turning the

power ON, the transceiver automatically starts scanning. Scanning

stops when receiving a call.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENTIONAL OPERATION

I Receiving and transmitting

NOTE: Transmitting without an antenna may damage the trans-

ceiver. See p. 2 for antenna attachment.

DTransmitting notes

• Transmit inhibit function

The transceiver has several inhibit functions which restrict trans-

mission under the following conditions:

- The channel is in mute condition.

Receiving:

q Rotate [VOL] to turn power ON.

w Toggle [CHANNEL SWITCH] (IC-F15S/F25S), rotate [CHAN-

NEL SELECTOR] (IC-F15/F25) or push one of [MR-CH 1] to

[MR-CH 4] key to select a channel.

- Channel is busy.

- Un-matched (or matched) CTCSS is received.

- The selected channel is a ‘receive only’ channel.

For IC-F15S/F25S:

The memory channels 3 and 4 are available when [MR-CH 3]

and [MR-CH 4] keys are assigned.

• Time-out timer

After continuous transmission for the pre-programmed time period,

the time-out timer activates, and causes the transceiver to stop

transmitting.

e When receiving a call, adjust the audio output level to a comfort-

able listening level.

• Penalty timer

Once the time-out timer activates, transmission is further inhibited

for a period determined by the penalty timer.

Transmitting:

Wait for the channel to become clear to avoid interference.

q While pushing and holding [PTT], speak into the microphone at

a normal voice level.

DDTMF transmission

If the transceiver has [DTMF Autodial] assigned to it, the automatic

DTMF transmission function is available.

• When a tone signalling system is used, the call procedure de-

scribed on p. 13 may be necessary.

w Release [PTT] to return to receive.

➥ Push [DTMF Autodial] to transmit the DTMF code.

IMPORTANT!: To maximize the readability of your signal;

1. Pause brieﬂy after pushing [PTT].

2. Hold the microphone 5 to 10 cm from your mouth, then speak

into the microphone at a normal voice level.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENTIONAL OPERATION

I Scrambler function

I Man Down Emergency Call

The optional voice scrambler units UT-109 (#01) and UT-110 (#01)

provide high performance private communication between stations

with the same scrambler codes.

The man down emergency call function transmits an emergency

call automatically, after the transceiver laying down in a horizontal

position for a pre-set time period. (The optional UT-113 ^{MAN DOWN}

UNIT is required.)

➥ Push and hold [Scrambler] to turn the scrambler function ON.

➥ Push [Scrambler] to turn the scrambler function OFF.

After the emergency call, the transceiver performs transmission and

reception alternately with the following conditions:

- Transmits the microphone signals.

I Setting the squelch level

- Receives the signal and emits audio.

The squelch circuit mutes the received audio signal depending on

the signal strength.

When the emergency cancel code is received, the function is can-

celled.

q While pushing [PTT] and [Lower],

rotate [VOL] to turn the power ON

to enter the squelch level adjust-

ment mode.

w Push [Upper] to increase the

squelch level (tight squelch) or

[Lower] to decrease the squelch

level (loose squelch).

[VOL]

IMPORTANT!: Set an emergency channel individually, to provide

certain emergency call operation is recommended.

[Upper]

[PTT]

[Lower]

e Rotate [VOL] to turn the power

OFF to ﬁx the squelch level.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPTIONAL UNIT INSTALLATION

I Optional unit installation

OPTIONAL UNIT INSTALLATION

I Scrambler unit installation

Install the optional unit as follows:

q Rotate [VOL] to turn the power OFF, and remove the battery

pack. (p. 3)

The following PC board modiﬁcation is required when installing the

optional UT-109 or UT-110.

q Rotate [VOL] to turn the power OFF, and remove the battery

pack. (p. 3)

w Remove the unit cover.

NOTE: Use a flat head screw driver or a similar flat instru-

ment, and insert into the hollow of the chassis, then lift and

take away the unit cover. (The removed cover cannot be used

again.)

w Remove the unit cover as shown at left (Optional unit installation.)

e Cut the pattern on the PCB at the TX mic circuit (MIC) and RX

AF circuit (DISC) as shown below.

r Install the scrambler unit as shown at left (Optional unit installa-

tion.)

t Replace the unit cover and the battery pack, then rotate [VOL] to

turn the power ON.

e Install the unit as shown below.

*This illustration is

described with the

UT-110.

NOTE: When uninstalling the

scrambler unit

Be sure to re-solder the discon-

nected points at left, otherwise no

TX modulation or AF output is

available.

r Replace the unit cover and the battery pack, then rotate [VOL] to

turn the power ON.

NOTE: The optional UT-109/UT-110 ^{SCRAMBLER UNITS}requires

some PC board modiﬁcations. Please refer to the additional in-

stallation as at right.

Download from Www.Somanuals.com. All Manuals Search And Download.

BATTERY CHARGING

I Battery charging

BATTERY CHARGING

I Caution

Prior to using the transceiver for the ﬁrst time, the battery pack must

be fully charged for optimum life and operation.

RDANGER Charge the speciﬁed Icom batteries only.

Only tested and approved for use with genuine Icom batteries. Fire

and/or explosion may occur when a third party battery pack or

counterfeit product is charged.

CAUTION: To avoid damage to the transceiver, turn it OFF while

charging.

• Recommended temperature range for charging:

+10°C to +40°C

CAUTION! NEVER insert battery pack/transceiver (with the bat-

tery pack attached) with wet or soiled into the charger. This may re-

sult in corrosion of the charger terminals or damage to the charger.

The charger is not waterproof and water can easily get into it.

- The Li-Ion battery functions within –20°C to +60°C

• Use the specified chargers (BC-119N, BC-121N and BC-160).

NEVER use another manufacturer’s charger.

• Use the optional AC adapter. NEVER use another manufacturer’s

AC adapter.

NEVER incinerate used battery packs. Internal battery gas may

cause an explosion.

NEVER immerse the battery pack in water. If the battery pack be-

comes wet, be sure to wipe it dry immediately (particularly the bat-

tery terminals) BEFORE attaching it to the transceiver. Otherwise,

the terminals will become corroded, or cause connection failure,

etc.

Recommendation:

Charge the supplied battery pack for a maximum of up to

10 hours. Li-Ion batteries are different from Ni-Cd batteries in

that it is not necessary to completely charge and discharge them

to prolong the battery life. Therefore, charging the battery in in-

tervals, and not for extended periods is recommended.

NEVER short the terminals of the battery pack. Also, current may

ﬂow into nearby metal objects, such as a necklace, etc. Therefore,

be careful when carrying with, or placing near metal objects, carry-

ing in handbags, etc.

AVOID leaving the battery pack in a fully charged, or completely

discharged condition for long time. It causes shorter battery life. In

case of leaving the battery pack unused for a long time, it must be

kept safely after discharge, or use the battery until the battery indi-

cator appears, then remove it from the transceiver.

If your battery pack seems to have no capacity even after being

charged, fully charge the battery pack again. If the battery pack still

does not retain a charge (or very little), a new battery pack must be

purchased.

Download from Www.Somanuals.com. All Manuals Search And Download.

BATTERY CHARGING

I Optional battery chargers

DRapid charging with the BC-160

The optional BC-160 provides rapid charging of optional Li-Ion bat-

tery packs.

ï AD-106 installation

q Install the AD-106 desktop charger adapter into the holder space

of the BC-119N/121N.

• An AC adapter (may be supplied with BC-160 depending on ver-

sion) or the DC power cable (OPC-515L/CP-17L) is additionally

required.

AD-106

Connectors

AC adapter

(Not supplied with

some versions.)

BP-231

TRANSCEIVER

Plugs

Optional OPC-515L

(for 13.8 V power

source) or CP-17L

(for 12 V cigarette

lighter socket) can

be used instead of

the AC adapter.

w Connect the plugs of the BC-119N/BC-121N to the AD-106 with

the connector, then install the adapter into the charger with the

supplied screws.

Screws supplied

with the charger

adapter

IMPORTANT!:

Lobs

Ensure the guide

lobs on the bat-

tery pack are

correctly aligned

with the guide

rails inside the

charger adapter.

-16

Guide rail

Download from Www.Somanuals.com. All Manuals Search And Download.

BATTERY CHARGING

DRapid charging with the BC-119N+AD-106

The optional BC-119N provides rapid charging of optional Li-Ion

battery packs.

The following items are additionally required:

• One AD-106 (purchase separately).

DRapid charging with the BC-121N+AD-106

The optional BC-121N allows up to 6 battery packs to be charged

simultaneously. The following items are additionally required.

• Six AD-106.

• An AC adapter (BC-124) or the DC power cable (OPC-656)

• An AC adapter (may be supplied with BC-119N depending on ver-

sion) or the DC power cable (OPC-515L/CP-17L).

TRANSCEIVER

BP-231

AD-106 charger

adapters are installed

in each slot.

AC adapter

(Not supplied with

some versions.)

AC adapter

(Purchased

separately)

AD-106 charger

adapter is installed

in BC-119N.

Optional OPC-515L

(for 13.8 V power

source) or CP-17L

(for 12 V cigarette

lighter socket) can

IMPORTANT!:

be used instead of

the AC adapter.

IMPORTANT!:

Lobs

Ensure the guide

lobs on the bat-

tery pack are

correctly aligned

with the guide

rails inside the

charger adapter.

Lobs

DC power cable

(OPC-656)

(Connect with the

DC power supply;

13.8 V/at least 7 A)

Ensure the guide

lobs on the battery

pack are correctly

aligned with the

guide rails inside

the charger adapter.

Guide rails

Download from Www.Somanuals.com. All Manuals Search And Download.

SWIVEL BELT CLIP

I MB-93 contents

SWIVEL BELT CLIP

e Clip the belt clip to a part of your belt. And insert the transceiver

into the belt clip until the base clip inserted fully into the groove.

Qty.

q Belt clip …………………………………………………………… 1

w Base clip …………………………………………………………… 1

I To attach

q Release the battery pack if it is attached. (p. 3)

w Slide the base clip in the direction of the arrow until the base clip

is locked and makes a ‘click’ sound.

r Once the transceiver is locked in place, it swivels as illustrated

below.

Download from Www.Somanuals.com. All Manuals Search And Download.

SWIVEL BELT CLIP

I To detach

q Turn the transceiver upside down in the direction of the arrow

w Release the battery pack if it is attached. (p. 3)

and pull out from the belt clip.

e Pinch the clip (q), and slide the base clip in the direction of the

arrow (w).

CAUTION:

HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR

DETACHING THE TRANSCEIVER FROM THE BELT CLIP.

Otherwise the transceiver may not be attached to the holder or

swivel properly if the transceiver is accidentally dropped and the

base clip is scratched or damaged.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPTIONS

DBATTERY PACK

DBELT CLIPS

• MB-93 SWIVEL BELT CLIP

• MB-94 BELT CLIP

• BP-230 Li-Ion BATTERY PACK

7.4 V/800 mAh Li-Ion battery pack, allows approx. 5.5 hours* op-

eration.

Exclusive alligator-type belt clip. The same as supplied with the

transceiver.

• BP-231 Li-Ion BATTERY PACK

7.4 V/1150 mAh Li-Ion battery pack, allows approx. 8 hours* op-

eration. The same as supplied with the transceiver.

• BP-232 Li-Ion BATTERY PACK

7.4 V/2000 mAh Li-Ion battery pack, allows approx. 14 hours* op-

eration.

• MB-96*/96F ^{LEATHER BELT HANGER}

*MB-93’s base clip is required.

DDC CABLES

• CP-17L CIGARETTE LIGHTER CABLE

Allows charging of the battery pack through a 12 V cigarette

lighter socket. (For BC-119N)

*Typical operation; Tx:Rx:Stand-by duty cycle=5:5:90

DCHARGERS

• BC-119N DESKTOP CHARGER + AD-106 CHARGER ADAPTER

+ BC-145 AC ADAPTER

• OPC-515L/OPC-656 ^{DC POWER CABLES}

Allows charging of the battery pack using a 13.8 V power source

instead of the AC adapter.

For rapid charging of battery packs. An AC adapter is supplied

with the charger depending on versions. Charging time: approx. 2

hours when BP-231 is attached.

• BC-121N ^MULTI-CHARGER + AD-106 CHARGER ADAPTER (6 pcs.)

+ BC-124 ^{AC ADAPTER}

For rapid charging of up to 6 battery packs (six AD-106’s are re-

quired) simultaneously. An AC adapter should be purchased sep-

arately. Charging time: approx. 2 hours when BP-231 is attached.

• BC-160 ^{DESKTOP CHARGER}+ BC-145 AC ADAPTER

For rapid charging of battery packs. An AC adapter is supplied

with the charger depending on versions. Charging time: approx. 2

hours when BP-231 is attached.

OPC-515L: For BC-119N

OPC-656 : For BC-121N

DOTHER OPTIONS

• SP-13 EARPHONE

Provides clear receive audio in noisy environment.

• HM-131L ^SPEAKER-MICROPHONE

Combination speaker-microphone that provides convenient oper-

ation while hanging the transceiver from your belt.

HM-131L has a moisture proof construction.

• HS-94/HS-95/HS-97 ^HEADSET+ VS-1L VOX/PTT CASE

HS-94: Ear hook type

HS-97: Throat microphone

HS-95: Neck-arm type

DOPTIONAL UNITS

• UT-108 DTMF DECODER UNIT

VS-1L: VOX/PTT switch box for hands-free operation, etc.

• FA-SC73US/FA-SC56VS/FA-SC57VS ^{STUBBY ANTENNAS}

Provides pager and code squelch capabilities.

• UT-109 (#01)/UT-110 (#01) ^{SCRAMBLER UNITS}

Non-rolling type (UT-109)/Rolling type (UT-110) voice scrambler

unit provides higher communication security.

• UT-113 ^{MAN DOWN UNIT}

FA-SC73US: 450–490 MHz

FA-SC57VS: 160–174 MHz

• FA-SC25U/FA-SC57U/FA-SC72U/FA-SC25V/FA-SC55V ^ANTENNAS

FA-SC25U: 400–430 MHz

FA-SC72U: 470–520 MHz

FA-SC55V: 146–174 MHz

FA-SC56VS: 150–162 MHz

FA-SC57U: 430–470 MHz

FA-SC25V: 136–155 MHz

Provides a measure of safety when working in a hazardous envi-

ronment, etc.

Some options may not be available in some countries. Please ask your

dealer for details.

Download from Www.Somanuals.com. All Manuals Search And Download.

DOC

CE versions of the IC-F15/S which display the “CE”

This warning symbol indicates that this equipment op-

erates in non-harmonised frequency bands and/or may

be subject to licensing conditions in the country of use.

Be sure to check that you have the correct version of

this radio or the correct programming of this radio, to

comply with national licensing requirement.

symbol on the serial number seal, comply with the

essential requirements of the European Radio and

Telecommunication Terminal Directive 1999/5/EC.

DECLARATION

OF CONFORMITY

We Icom Inc. Japan

1-1-32, Kamiminami, Hirano-ku

Osaka 547-0003, Japan

1-1-32, Kamiminami, Hirano-ku

Osaka 547-0003, Japan

0168

Declare on our sole responsibility that this equipment complies with the

essential requirements of the Radio and Telecommunications Terminal

Equipment Directive, 1999/5/EC, and that any applicable Essential Test

Suite measurements have been performed.

Declare on our sole responsibility that this equipment complies with the

essential requirements of the Radio and Telecommunications Terminal

Equipment Directive, 1999/5/EC, and that any applicable Essential Test

Suite measurements have been performed.

Düsseldorf 30th June 2004

Düsseldorf 30th July 2004

Place and date of issue

Kind of equipment: VHF TRANSCEIVER

Kind of equipment: UHF TRANSCEIVER

Type-designation:

iC-f15/s

Type-designation:

iC-f25/s

Authorized representative name

136 174 MHz 12.5 kHz/20 kHz/25 kHz

400–470 MHz 12.5 kHz/20 kHz/25 kHz

Version (where applicable):

This compliance is based on conformity with the following harmonised

standards, specifications or documents:

i) EN 301 489-1 v1.3.1 (Sept 2001)

ii) EN 301 489-5 (August 2000)

This compliance is based on conformity with the following harmonised

standards, specifications or documents:

i) EN 301 489-1 v1.3.1 (Sept 2001)

ii) EN 301 489-5 (August 2000)

iii) EN 60950 (August 1992+A11)

iv) EN 300 086-2 (March 2001)

v) EN 300 219-2 (March 2001)

Signature

vi) EN 300 113-2 (March 2001)

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

Download from Www.Somanuals.com. All Manuals Search And Download.

Grizzly Grinder G0567 User Manual
GSI Outdoors Clothes Dryer PNEG 552 User Manual
Hans Grohe Plumbing Product 04065XX0 User Manual
Hasbro Games 06954 06922 User Manual
Heartland Range Toledo XT User Manual
Hotpoint Washer Dryer HE7L 292 User Manual
HP Hewlett Packard Computer Monitor W17Q User Manual
HP Hewlett Packard Network Card 5991 6764 User Manual
Husqvarna Chainsaw 1153178 95 User Manual
IBM Computer Monitor 6734 AB9 User Manual