INSTRUCTION MANUAL
PMR446 FM TRANSCEIVER
iF22SR
Download from Www.Somanuals.com. All Manuals Search And Download.
I 2 types of built-in Code Squelch Systems:
CTCSS; Continuous Tone Coded Squelch System
DTCS; Digital Tone Code Squelch
CTCSS* and DTCS* encoder/decoder are standard, providing
quiet stand-by. Audio (voice) signals are output only when a sig-
nal with a matched CTCSS or DTCS tone signal is received—
very helpful for group communications. (pgs. 14, 28)
*Select one of CTCSS or DTCS for your convenience.
I 2 types of “Ring” function
The “Smart-Ring”* function and the “Call-Ring” function are avail-
able for smart and simple station calls providing a telephone-
style ring when called. 16 different ringing tones are available.
(pgs. 19–20)
*“Smart-Ring” function available only when all of your group sta-
tion use the same CTCSS tone code on the same operating
channel.
SUPPLIED ACCESSORIES
• Belt clip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
• BC-146* (Regular charger). . . . . . . . . . . . . . . . . . . . . . . . 1 set
(*Depends on version)
DAttach or detach the belt clip to the transceiver as illustrated
below.
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
IMPORTANT
READ ALL INSTRUCTIONS carefully and completely
before using the transceiver.
SAVE THIS INSTRUCTION MANUAL–This instruction
manual contains important operating instructions for the
IC-F22SR PMR446 FM transceiver.
CAUTIONS
RWARNING! NEVER hold the transceiver so that the an-
tenna is very close to, or touching exposed parts of the body,
especially the face or eyes, while transmitting. The transceiver
will perform best if the microphone is 5 to 10 cm away from the
lips and the transceiver is vertical.
RWARNING! NEVER operate the transceiver with a
headset or other audio accessories at high volume levels.
DO NOT push the PTT when not actually desiring to transmit.
DO NOT modify the transceiver for any reason.
AVOID using or placing the transceiver in direct sunlight or in
areas with temperatures below –25°C or above +55°C. In an
extreme low temperature environment (around –25°C), the ca-
pacity of Alkaline or dry cell batteries may exhaust quickly. In
such case, we recommend to replace the batteries, when the
“Low Battery” warning appears during transmission.
The use of non-Icom battery packs/chargers may impair trans-
ceiver performance and invalidate the warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
TABLE OF CONTENTS
FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i–ii
SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii
IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
1 PANEL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–3
‘ Switches, controls, keys and connectors . . . . . . . . . . . . . . . .1–2
‘ LED indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2 BATTERY PACKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4–10
‘ Battery pack replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
‘ Battery cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
‘ Battery charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
‘ Charging NOTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
‘ Battery case (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
3 BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11–18
‘ Receiving and transmitting . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
‘ Setting squelch level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
‘ Auto scan function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
‘ Setting the group code number . . . . . . . . . . . . . . . . . . . . . .14-18
4 RING FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19–20
‘ Smart-Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
‘ Call-Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
5 OTHER FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21–23
‘ Monitor audible function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
‘ Time-Out Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
‘ Power save function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
‘ Low battery indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
‘ Optional HM-75A functions . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
6 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
7 OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25–26
8 GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27–28
9 CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29–30
‘ DECLARATION OF CONFORMITY . . . . . . . . . . . . . . . . . . . . .30
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
PANEL DESCRIPTION
1
‘
Switches, controls, keys and
connectors
q [CH] selector
w [VOL/ POWER]
Antenna
y TX/RX
Indicator LED
e [S-Ring
/C-Ring] key
u External
[SP]/[MIC] jack
(see below)
r [PTT]
t [MONI] key
Speaker
MIC
u External
Ext. MIC.
[SP]/[MIC] jack
MIC
SP
Ext. SP
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1
PANEL DESCRIPTION
q CHANNEL SELECTOR [CH]
• Rotate the selector to select the desired channel number 1 to
15. (pgs. 11, 12)
• Select the Auto Scan channel No.16. (p. 13)
• Select the Call-Ring melody. (p. 19)
w VOLUME/POWER CONTROL [VOL/POWER]
• Rotate the [VOL/POWER] clockwise to turn the power ON/OFF.
A long power ON beep emits when turning the power ON.
• Rotate clockwise to increase and counterclockwise to decrease
the audio volume.
e SMART-RING/CALL-RING KEY [S-Ring/C-Ring]
• Push to send a Smart-Ring call. (p. 19)
• Push and hold to send a Call-Ring. (p. 19)
r PTT SWITCH [PTT]
• Push and hold to transmit; release to receive.
t MONITOR KEY [MONI]
• Push and hold to open the noise/tone squelch.
• Push to turn the tone squelch ON.
y TX/RX INDICATOR LED [LED]
• Lights red while transmitting.
• Lights green while receiving a signal, or squelch is open.
• Lights orange while sending/receiving a Smart-Ring call. (p. 19)
• Indicates the Low-battery condition. (p. 3)
u EXTERNAL SPEAKER AND MICROPHONE JACKS [SP]/[MIC]
• Connects an optional speaker-microphone such as HM-75A.
(p. 23)
Download from Www.Somanuals.com. All Manuals Search And Download.
2
1
PANEL DESCRIPTION
‘
LED indicator
The TX/RX indicator LED indicates informa-
tion in several ways as follows;
(Ref.; R=Red, G=Green, O=Orange)
[Brink patterns]
• TX: Turns Red while transmitting a signal.
R
• RX (Busy): Turns Green while receiving a signal.
G
• Smart-Ring: Calling or answering back the Smart-Ring now.
O
O
• Fast/Slow scan: CH scanning or CTCSS FIND is functioning now.
G
G
• Low BATT1: You should charge the battery. (blinks slowly)
R
R
R
• Low BATT2: You must charge the battery. (blinks fast)
R
R
R
• TX low BATT1: Low BATT1 was detected during TX mode.
R
R
• TX low BATT2: Low BATT2 was detected during TX mode.
R
R
R
R
CAUTION:
• Low BATT3: If you did not charge the battery after Low BATT2
warning has appeared, the Low BATT3 warning beep emits for 15
sec. then the power turns OFF automatically.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
BATTERY PACKS 2
‘
Battery pack replacement
Before replacing the battery pack, the volume control MUST be ro-
tated fully counterclockwise,
until a click is heard, to turn the
power OFF.
• Push the battery release for-
ward, then pull the battery
pack upward with the trans-
ceiver facing you.
DBATTERY PACKS
Charging period
Battery
pack
Operating
period*
Voltage Capacity
BC-144,
BC-119 or
BC-121
BC-146
attery case for AA
(R6) × 6 alkaline
B
BP-208
1100
BP-209 7.2 V
BP-210 7.2 V
12 hrs
1.5 hrs
2 hrs
14.5 hrs
21.5 hrs
mAh
1650
mAh
18.5 hrs
600
mAh
7.2 V
6.5 hrs
1 hr
8
BP-222
hrs
* Operating periods are calculated under the following conditions;
Tx : Rx : standby =5 : 5 : 90
Operating period depends on the alkaline cells used. (BP-208 only)
Download from Www.Somanuals.com. All Manuals Search And Download.
4
BATTERY PACKS
2
‘
Battery cautions
• CAUTION! NEVER short the terminals of the battery pack (or
charging terminals of the transceiver). Also, current may flow into
nearby metal objects such as a necklace, so be careful when plac-
ing battery packs (or the transceiver) in handbags, etc.
Simply carrying with or placing near metal objects such as a neck-
lace, etc. causes shorting. This will damage not only the battery
pack, but also the transceiver.
• NEVER incinerate used battery packs. Internal battery gas may
cause an explosion.
• NEVER immerse the battery pack in water. If the battery pack be-
comes wet, be sure to wipe it dry BEFORE attaching it to the
transceiver.
• Clean the battery terminals to avoid rust or miss contact.
• Keep battery contacts clean. It’s a good idea to clean battery ter-
minals once a week.
If your battery pack seems to have no capacity even after being
charged, completely discharge it, then fully charge the battery pack
again. If the battery pack still does not retain a charge (or only very
little charge), a new battery pack must be purchased.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
BATTERY PACKS
2
‘
Battery charging
DRegular charging with the BC-146
The supplied* BC-146 provides regular charging of optional battery
pack with/ without transceiver.
(*depends on version)
DSpacer combination.
Especially when charging the battery with the transceiver;
• Be sure to attach the spacer (Spacer B/C) to the adaptor (Spacer
A) with the orientation as follows.
• Attach the spacer (Spacer B/C) to the adaptor with the orientation
of the stamp “ ” pointing up.
Check orientation
and
Spacer A
Spacer B/C
NOTE: Push the notch carefully
when removing the spacer from
the adaptor.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
BATTERY PACKS
2
DRegular charging with the BC-146 (continued)
• First insert the spacer in to the BC-146, then insert the battery or
the transceiver.
• Be sure to check orientation and the spacer combination.
Avoid overcharging–Batteries must be removed from the charger
to stop charging. Batteries should not be
charged for more than 24 hours.
Turn power OFF
BP-209, BP-210
or BP-222 only
Check
AC adaptor
orientation*
Charging indicator
*Viewable stamps of the spacer may differ according to the
spacer combination. See p. 6 for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
BATTERY PACKS
2
DRapid charging with the BC-121+AD-94 (#11)
The optional BC-121 allows up to 6 battery packs to be charged si-
multaneously. The following are additionally required.
• Six AD-94 (#11) (Some versions require additional AD-99s).
• An AC adaptor (may be supplied with the BC-121 depending on
version).
Turn power OFF.
AC adaptor
(purchased
separately)
AD-99
MULTI-CHARGER
Charge indicator
(each indicator functions independently)
D Rapid charging with
the BC-144+AD-99
The optional BC-144 pro-
vides rapid charging of op-
tional battery packs.
Turn power OFF.
Check orientation
for correct charg-
ing. (Insert togeth-
er with charging
adaptor.)*
The following are addition-
ally required:
• One AD-99 (depends on
version).
• An AC adaptor (may be
supplied with the BC-144
depending on version).
BC-144
Download from Www.Somanuals.com. All Manuals Search And Download.
8
BATTERY PACKS
2
‘
Charging NOTE
Prior to using the transceiver for the first time, the battery pack must
be fully charged for optimum life and operation.
• Recommended temperature range for charging:
+10°C to +40°C.
• Use the supplied charger or optional charger (BC-119/BC-121/BC-
144 for rapid charging, BC-146 for regular charging) only. NEVER
use other manufacturers’ chargers.
The optional BP-209, BP-210 or BP-222 battery packs include
rechargeable Ni-Cd (Ni-MH: BP-210) batteries and can be charged
approx. 300 times. Charge the battery pack before first operating
the transceiver or when the battery pack becomes exhausted.
If you want to charge the battery pack more than 300 times, the fol-
lowing points should be observed:
• Avoid overcharging–batteries must be removed from the charger
to stop charging. Batteries should not be charged for more than
24 hours.
• Use the battery until it becomes almost completely exhausted
under normal conditions.
DBattery pack life
When the operating period becomes extremely short even after
charging the battery pack fully, a new battery pack is needed.
NOTE for the rapid chargers : The charger rapidly charges a
battery pack to a specified level, not a completed level, to pre-
vent overcharging. Leave the battery pack in the charger for a
few more hours (up to 15 hours; depending on battery condi-
tion) after the LED indicator turns green, to charge the battery
completely.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
BATTERY PACKS
2
‘
Battery case (Option)
When using a BP-208 OPTIONAL BATTERY CASE attached to the
transceiver, install 6 AA (R6) size alkaline batteries as illustrated
below.
DCAUTIONS
• Use ALKALINE batteries only.
• Make sure all battery cells are the same brand, type and ca-
pacity.
• Never mix old and new batteries.
Either of the above may cause a fire hazard or damage the
transceiver, if ignored.
• Never incinerate used battery cells since internal battery gas
may cause them to rupture.
• Never expose a detached battery case to water.
If the battery case gets wet, be sure to wipe it dry before using
it.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
3 BASIC OPERATION
‘
Receiving and transmitting
CHARGE the battery pack before first operating the transceiver.
The transceiver has been pre-programmed with all the PMR fre-
quency channels and CTCSS tone
codes as a default. The CTCSS tone
number can be changed if required.
[CH selector]
Receiving:
[VOL
/POWER]
q Rotate the [VOL] knob clockwise to
turn the power ON.
w Rotate the [CH] selector to select the
desired operating channel.
[S-Ring
/C-Ring]
• Setting the your group code number
if required. (pgs. 14–16)
[PTT]
[MONI]
e Listen for a transmission and adjust
[VOL] to a comfortable listening level.
• [LED] turns to green, when the re-
ceived signal contains same CTCSS
or DTCS code number.
*microphone
• When no transmission is heard,
push and hold [MONI] while adjust-
ing [VOL].
The transceiver is now set to receive desired calls on the selected
channel.
Transmitting:
Wait for the channel to become clear to avoid interference.
r While pushing and holding [PTT], speak into the microphone at a
normal voice level.
• [LED] turns to red.
t Release [PTT] to return to receive.
*IMPORTANT: To maximize the readability of your transmitted sig-
nal, pause a few sec. after pushing [PTT], hold the microphone 10
to 15 cm from your mouth and speak at a normal voice level.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
BASIC OPERATION
3
• Frequency channel/CTCSS tone list (default)
Tone (Hz)*2
NO
Channel RX/TX Freq. (MHz)*1 CH spacing
No.1
No.2
446.00625
446.01875
446.03125
446.04375
446.05625
446.06875
446.08125
446.09375
446.00625
446.01875
446.03125
446.04375
446.05625
446.06875
446.08125
Auto Scan
Narrow
Narrow
Narrow
Narrow
Narrow
Narrow
Narrow
Narrow
Narrow
Narrow
Narrow
Narrow
Narrow
Narrow
Narrow
------
NO
No.3
NO
No.4
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
------
No.5
No.6
No.7
No.8
No.9
No.10
No.11
No.12
No.13
No.14
No.15
No.16
*1: All operating channel frequencies are fixed.
*2: CTCSS tone frequencies can be programmed by you. You
can use DTCS (Digital Tone Code Squelch) instead of
CTCSS. (p. 17)
Download from Www.Somanuals.com. All Manuals Search And Download.
12
BASIC OPERATION
3
‘
Setting squelch level
The squelch circuit mutes the received audio signal depending on
the signal strength.
q While pushing and holding
[VOL
/POWER]
[PTT] and [MONI], turn the
transceiver’s power ON to
enter the squelch adjustment
mode.
[S-Ring
/C-Ring]
w Push [S-Ring/C-Ring] to in-
crease the squelch level (tight
squelch) or [MONI] to de-
crease the squelch level (loose
squelch).
[PTT]
[MONI]
• Squelch level will be fixed after 1 sec.
DOpen the squelch
• Pushing and holding [MONI] cancels the squelch function. You
can receive any signals on a channel.
• Push [MONI] to turn ON the tone squelch function again.
‘
Auto Scan function
Auto scan function proceeds in sequence from lower channel to
higher channel numbers. Scanning searches for signals automati-
cally and makes it easier to locate new stations for contact or lis-
tening purposes.
q Rotate the [CH] select knob to CH 16.
w Scan starts automatically.
• TX/RX indicator LED blinks green slowly.
• When receiving a signal, scan pauses until the signal disappears.
CONVENIENT: You can perform the scan start/stop by the optional
HM-75A SPEAKER-MICROPHONE [Mic A] key.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
BASIC OPERATION
3
‘
Setting the group code number
DUSING THE CTCSS TONE CODE
The transceiver is equipped with 52 CTCSS tones. (See next page)
CTCSS operation provides communication with silent standby since
you will only receive calls from group members using the same
CTCSS tone.
You can assign a different tone to CH 1 to CH 15 independently.
q While pushing and holding [PTT], [S-Ring/C-Ring], [MONI], turn
[VOL] to turn the power ON.
w Select the desired CH 1 to CH 15 that you want to assign the
CTCSS tone frequency to.
e Push and hold [S-Ring/C-Ring] until a beep (Pi) is emitted.
r Push [PTT] the necessary number of times to choose the 10 digit
of the desired code from the channel list.
t Push [S-Ring/C-Ring].
• Confirmation beep is emitted. (See next page.)
y Push [PTT] the necessary number of times to choose the 1 digit
of the desired code from the frequency list.
u Push [S-Ring/C-Ring].
i Turn the power OFF, and then ON again.
[Example]
To assign tone code No. 28 as CH1;
q While pushing and holding [PTT], [S-Ring/C-Ring] and [MONI],
turn [VOL] to power ON.
w Select the CH 1, then push and hold [S-Ring/C-Ring] until a beep
(Pi) is emitted.
e Push [PTT] twice to choose the 10 digit of the desired channel.
r Push [S-Ring/C-Ring], then push [PTT] eight times to choose the
1 digit of the desired code.
t Push [S-Ring/C-Ring]. A long beep and 3 short beeps are emit-
ted.
y Turn the power OFF, and then ON again.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
BASIC OPERATION
3
• CTCSS tone code list
: EIA/TIA standard code (Recommended to use these.)
Freq.
OFF
67.0
69.3*
71.0
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
No. Freq.
No. Freq.
32 171.3
33 173.8
34 177.3
35 179.9
36 183.5
37 186.2
38 189.9
39 192.8
40 196.6
41 199.5
42 203.5
43 206.5
44 210.7
45 218.1
46 225.7
47 229.1
No.
48
49
50
51
52
Freq.
233.6
241.8
250.3
254.1
270.4
No.
0
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
159.8
162.2
165.5
167.9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
*Reserved for Smart-Ring function
(Unit: Hz)
• Confirmation beep list
Confirmation beep
Confirmation beep
Push [PTT]
no
Push [PTT]
5 (Fifth)
G
GGGGG
G
G
1 (Once)
2 (Twice)
3 (Third)
4 (Fourth)
G; Single beep
6 (Sixth)
GG
GG
7 (Seventh)
8 (Eighth)
9 (Ninth)
GGG
GGGG
GGG
GGGG
; Long beep
Download from Www.Somanuals.com. All Manuals Search And Download.
15
BASIC OPERATION
3
DCTCSS FIND
This transceiver can detect the CTCSS tone frequency in the re-
ceived signal. By monitoring a signal that is being transmitted from
the other station, you can determine the tone frequency required to
communicate with them.
This function very useful when you are going to communicate with
unknown CTCSS code number stations. ‘CTCSS FIND’ scans all
of the CTCSS codes, then stops when a tone code is detected.
q While pushing and holding [S-Ring/C-Ring], [MONI], turn [VOL]
to turn the power ON.
w Select the desired CH 1 to CH 15 that you want to assign the
CTCSS tone code.
e Push and hold [S-Ring/C-Ring] until a beep (Pi) is emitted.
• ‘CTCSS FIND’ starts to scan the code.
r ‘CTCSS FIND’ stops when the tone code is detected.
t Push [S-Ring/C-Ring] to determine the tone code number.
y Turn the power OFF, and then ON again.
DTurn the squelch function ON/OFF
• Push and hold [MONI] to turn the tone squelch function OFF.
• You can receive any signals on a channel, when you receive
the other group’s signal.
• Push [MONI] to turn ON the tone squelch function again. You
can receive only signals containing the same as your group
code.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
BASIC OPERATION
3
DUSING THE DTCS CODE
This transceiver is equipped with 83 DTCS codes. DTCS operation
provides communication with silent standby since you will only re-
ceive calls from group members using the same DTCS number.
You can assign different numbers to CH 1 to CH 15 independently.
q While pushing and holding [PTT], [S-Ring/C-Ring] and [MONI],
turn [VOL] to turn the power ON.
w Select the desired CH 1 to CH 15 that you want to assign the
DTCS code to.
e Push and hold [MONI] until a beep (Pi) is emitted.
r Push [PTT] the necessary number of times to choose the 100
digit of the desired code number.
t Push [S-Ring/C-Ring].
• Confirmation beep is emitted. (See p. 15)
y Push [PTT] the necessary number of times to choose the 10 digit
of the desired code number.
u Push [S-Ring/C-Ring].
• Confirmation beep is emitted. (See p. 15)
i Push [PTT] the necessary number of times to choose the 1 digit
of the desired code number.
o Push [S-Ring/C-Ring].
• Confirmation beep is emitted. (See p. 15)
!
!
0
1
Push [PTT] once more, if you want to use Inverse mode.
Push [S-Ring/C-Ring] to complete the setting.
• Confirmation beep is emitted. (See p. 15)
!
2
Turn the power OFF, and then ON again.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
BASIC OPERATION
3
[Example]
To assign code ‘261I (Inverse)’ as CH12;
q While pushing and holding [PTT], [S-Ring/C-Ring], [MONI], turn
[VOL] to turn the power ON.
w Select CH 12.
e Push and hold [MONI] until a beep (Pi) is emitted.
r Push [PTT] twice to choose the 100 digit of the code number.
t Push [S-Ring/C-Ring].
• Confirmation beep is emitted. (See p. 15)
y Push [PTT] six times to choose the 10 digit of the code number.
u Push [S-Ring/C-Ring].
• Confirmation beep is emitted. (See p. 15)
i Push [PTT] once to choose the 1 digit of the code number.
o Push [S-Ring/C-Ring].
• Confirmation beep is emitted. (See p. 15)
!
!
!
0
1
2
Push [PTT] once more, to use Inverse mode.
*You can skip step !, if you want to use Normal mode.
Push [S-Ring/C-Ring] to complete the setting.
• Confirmation beep is emitted. (See p. 15)
Turn the power OFF, and then ON again.
0
• DTCS code list (EIA/TIA standard code)
023
025
026
031
032
043
047
051
054
065
071
072
073
074
114
115
116
125
131
132
134
143
152
155
156
162
165
172
174
205
223
226
243
244
245
251
261
263
265
271
306
311
315
331
343
346
351
364
365
371
411
412
413
423
431
432
445
464
465
466
503
506
516
532
546
565
606
612
624
627
631
632
654
662
664
703
712
723
731
732
734
743
754
Download from Www.Somanuals.com. All Manuals Search And Download.
18
4 RING FUNCTION
‘
Smart-Ring
The ring function has an answer back feature. This allows you to
confirm whether or not a call has reached the member of your
group even if the operator is temporarily away from the transceiver.
DSmart-Ring operation (see right)
q Set the same operating channel and CTCSS tone* code for all of
your group transceivers.
w Push [S-Ring/C-Ring] to send the Smart-Ring call.
• When a member of your group station answers your call, then
the transceiver emits beep tones for every 30 sec. and TX/RX
indicator blinks with an orange color.
• Push [MONI] to cancel the Ringer beep and indication.
• When no answer comes back, the transceiver emits short fail-
ure beep tones.
e Push [PTT] to answer the call and to stop the beeps and blink-
ing.
*NOTE: This function is available only when the called station
has use the same CTCSS tone code and the same operating
channels as you.
‘
Call-Ring
Sends the pre-selected ring tone to your group members.
DSelect the Call-Ring melody
q While pushing and holding [PTT] and [S-Ring/C-Ring], rotate
[VOL] to turn the power ON.
• A sample melody is emitted.
w Rotate [CH] to select the ringer melody.
• Push [S-Ring/C-Ring] to monitor the selected melody once
more.
e Turn the power OFF to determine the melody.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
RINGER FUNCTION
4
• Smart-Ring operation
push [S-Ring/C-Ring]
Answer back (automatic)
Communication
DCall your group member with Call-Ring melody
➥ Pushing and holding [S-Ring/C-Ring] to sends a ring tone with-
out pushing [PTT].
• The ring tone is emitted while the [S-Ring/C-Ring] key is
pressed.
• The same ring tone comes from your group station’s speaker.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
5 OTHER FUNCTIONS
‘
Monitor audible function
The monitor function allows you to open the transceiver’s squelch
manually to check whether a channel is busy or not. The trans-
ceiver has 2 conditions for receive standby:
• Audible condition:
This condition mutes audio ONLY when
no carrier is present. You can receive (or
monitor) any signals on a channel.
• Push and hold the [MONI] switch to can-
cel the CTCSS or DTCS tone squelch
All signals are
received
function.
Any audio mute functions are cancelled
while pushing the [MONI] switch.
• Inaudible condition: This condition
mutes ALL signals except those directed
to you. Therefore you should check a
channel’s condition (busy or not) with the
monitor function before transmitting.
• Push the [MONI] switch momentarily to
select the inaudible condition.
Only signals con-
taining the proper
tone are received
‘
Time-Out Timer
The transceiver has time-out timer function. This function prevents
continuous, extend transmissions. This timer automatically turns a
transmission OFF 3 min. after it starts.
A warning beep emits 10 sec. before the limit is reached.
The end beep emits 5 times to announce the end of the transmis-
sion.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
OTHER FUNCTIONS
5
‘
Power save function
The power save function reduces the current drain to conserve bat-
tery power.
• The power save function is automatically turned ON when no op-
eration is performed or no signal is received for 5 sec.
‘
Low battery indication
The TX/RX LED indicates 4 levels of the “Low battery” condition as
follows.
If the “Low battery” warning appears during operation, please
charge or replace the battery.
[Brink patterns]
• Low BATT1: You should charge the battery. (blinks slowly)
R
R
R
• Low BATT2: You must charge the battery. (blinks fast)
R
R
R
• TX low BATT1: Low BATT1 was detected during TX mode.
R
R
• TX low BATT2: Low BATT2 was detected during TX mode.
R
R
R
R
In an extreme low temperature surrounding (around –20°C), the
capacity of the battery may exhaust quickly (especially Alkaline
batteries). In such case, we recommend to charge the battery or
replace the batteries, when the “Low Battery” Indication appears
during operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
OTHER FUNCTIONS
5
‘
Optional HM-75A functions
The optional HM-75A allows you to remotely send Smart-Ring/Call-
Ring calls, open the squelch, etc. The switches on the HM-75A
function as follows.
CAUTION: When connecting the HM-75A to the transceiver, make
sure that the transceiver is turned OFF, otherwise the transceiver
may malfunction.
Key
Push
Push and hold
Mic UP
Mic DOWN
Sends Smart-Ring.
Turn the Tone
Squelch ON.
Start/Stop scan B.
---
Sends Call-Ring.
Turn the Tone
Squelch OFF.
---
Mic A
Mic B
---
Mic A
Mic UP
Mic B
Mic Down
Download from Www.Somanuals.com. All Manuals Search And Download.
23
SPECIFICATIONS 6
GENERAL
• Frequency coverage
: 446.00625–446.09375 MHz
• Mode
: F3E (FM)
• No. of operating Ch.
: 8 (simplex)
• Power supply requirement : 7.2 V (R6x6) or BP-222
• Current drain
: 0.6 A approx.
: –25˚C to +55˚C
: 38
• Operating temp. range
• No. of CTCSS freq.
• Dimensions
: 54(W)x128(H)x37(D) mm
(projections not included)
• Weight
: 317 g (including BP-222 Ni-Cd batteries)
TRANSMITTER
• Output power
: Less than 500 mW ERP
• Ext. mic. connector
: 3-conductor 2.5 (d) mm/2.2 kΩ
RECEIVER
• Sensitivity
: Less than 26.5 dBµV/m
(20 dB SINAD)
• Audio output power
(at 7.2 V DC)
• Ext. speaker connector
: More than 500 mW at 5 %
distortion with an 8 Ω load
: 2-conductor 3.5 (d) mm/8 Ω
All stated specifications are subject to change without no-
tice or obligation.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
7 OPTIONS
‘
Options
DBATTERY PACKS
• BP-208 BATTERY CASE
Allows a set of Alkaline batteries to operate the handheld when
charging the rechargeable battery or in emergencies, etc. 6 AA
(R6) cells are required.
• BP-209 Ni-Cd BATTERY PACK
7.2 V/1100 mAh Ni-Cd battery pack, allows more than 12 hours
operation.
• BP-210 Ni-MH BATTERY PACK
7.2 V/1650 mAh Ni-MH battery pack, allows approx. 18.5 hours
operation.
• BP-222 Ni-Cd BATTERY PACK
7.2 V/600 mAh Ni-Cd battery pack, allows approx. 6.5 hours op-
eration (Same as supplied with models).
DCHARGER
• BC-119 DESKTOP CHARGER + AD-94 (#11)
For rapid charging of battery packs. An AC adaptor is supplied
with the charger. Charging time: 1.5 to 2 hrs.
• BC-121 MULTI-CHARGER + AD-94 (#11)
For rapid charging up to 6 battery packs simultaneously. An AC
adaptor may be supplied depending on version. Six AD-94 ’s
(#11) are necessary. Charging time: 1.5 to 2 hrs.
• AD-99 CHARGER ADAPTOR
• BC-144 DESKTOP CHARGER
For rapid charging of BP-209 (Ni-Cd), BP-210 (Ni-MH) and BP-
222 (Ni-Cd).
• BC-146 DESKTOP CHARGER
For regular charging of BP-209 (Ni-Cd), BP-210 (Ni-MH) and BP-
222 (Ni-Cd).
Download from Www.Somanuals.com. All Manuals Search And Download.
25
OPTIONS
7
DOTHER OPTIONS
• HM-46L/HM-75A/HM-131L SPEAKER MICROPHONE
Combination speaker-microphone that provides convenient oper-
ation while hanging the transceiver from your belt.
HM-75A has programmable function key Mic UP, Mic DOWN, Mic
A, Mic B.
HM-131L has moisture proof construction.
• SP-13 EARPHONE
Provides clear receive audio in noisy environments.
• MB-68 BELT CLIP
Same as that supplied with the transceiver.
• MB-74 BELT CLIP
Exclusive alligator-type belt clip.
• VS-1SL VOX/PTT CASE
The VS-1SL has a PTT switch and VOX function. The VS-1SL
must be used with an Icom headset such as the HS-94, etc.
• HS-94 HEADSET
An ear-attachable, earphone/microphone for use with the Icom
handheld transceivers. The HS-94 must be used in conjunction
with the VS-1SL VOX/PTT CASE.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
8 GLOSSARY
✔ What is squelch?
A squelch circuit allows you to mute undesired noise while re-
ceiving no signal and emit audio while receiving signals.
This provides quiet standby. The [MONI] key cancels the
squelch setting. This is useful to listen to weak signals that
do not open the squelch.
✔ Talk Range
The IC-F22SR is designed to maximize performance and im-
prove transmission range in the field. However, the single
most important factor in transmit range (talk power) is your
surrounding environment. These radios are “line of sight” ra-
dios and as such, transmission range is influenced by the de-
gree to which you can “see” the other communicating party.
Large concrete structures and heavy foliage or transmission
from inside a building or vehicle will reduce your talk power.
• Optimal range: wide, open areas free of obstructions.
• Medium range: large buildings or trees blocking your line of
sight.
• Minimum range: mountainous areas or areas of heavy fo-
liage.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
GLOSSARY
8
✔ What is CTCSS (Continuous Tone Coded Squelch Sys-
tem) ?
CTCSS (Continuous Tone Coded Squelch System) allows
communication with silent stand by. Only signals containing
your group code can open the squelch.
This conveniently eliminates unwanted audio and is useful in
group activities or security related activities where unwanted
output can be a problem. Note that CTCSS group mode is not
private—anyone can receive your calls.
The IC-F22SR is equipped with max. 52 tone codes for CTCSS
use. Selecting a code applies it to all 8 operating channels.
Each push of [PTT] superimposes your group code over your
transmit signal; and, only signals containing the same code can
open your squelch. To temporarily hear all signals (including
noise) push and hold [MONI]. Do not use CTCSS if you want to
be able to hear signals on all channels.
✔ Auto Scan function + Smart-Ring
The Auto Scan function searches for signals automatically
and makes it easier to locate new stations for contact or lis-
tening purposes. BUT because the Auto Scan function
checks each operating channel for only a few moments, the
transceiver's response accuracy to Smart-Ring calls is re-
duced. Use one of CH 1–15 when you and your group are
going to use the Smart-Ring function, otherwise the Smart-
Ring function may fail to answer-back the call.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
9 CE
ABOUT CE
CE Versions of the IC-F22SR which display the
“CE” symbol on the serial number seal, comply
with the essential requirements of the European
Radio and Telecommunication Terminal Directive
1999/5/EC.
This warning symbol indicates that this equip-
ment operates in non-harmonised frequency
bands and/or may be subject to licensing condi-
tions in the country of use. Be sure to check that
you have the correct version of this radio or the
correct programming of this radio, to comply with
national licensing requirement.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
CE
9
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Count on us!
< Intended Country of Use >
GER
AUT
GBR
IRL
FRA
SUI
NED
BEL
LUX
ESP
POR
ITA
GRE
SWE
DEN
FIN
A-6069D -1EU-q
Printed in Japan
© 2001 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|