INSTRUCTION MANUAL
VHF MARINE TRANSCEIVER
iM2A
This device complies with Part 15 of the FCC Rules. Operation is sub-
ject to the follow two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
IN CASE OF EMERGENCY
RECOMMENDATION
If your vessel requires assistance, contact other vessels and
the Coast Guard by sending a distress call on Channel 16.
CLEAN THE TRANSCEIVER THOROUGHLY WITH FRESH
WATER after exposure to salt water.
Otherwise, the transceiver’s keys, switches and controllers
may become inoperable due to salt crystallization.
❍ USING CHANNEL 16
DISTRESS CALL PROCEDURE
1. “MAYDAY MAYDAY MAYDAY.”
2. “THIS IS ...........................” (name of vessel)
3. Your call sign or other indication of the ves-
sel.
4. “LOCATED AT .....................” (your position)
5. The nature of the distress and assistance re-
quired.
6. Any other information which might facilitate
the rescue.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
FOREWORD
FEATURES
Thank you for purchasing this Icom product. The IC-M2A VHF
MARINE TRANSCEIVER is designed and built with Icom’s su-
perior technology and craftsmanship. With proper care this
product should provide you with years of trouble-free operation.
ꢀ Waterproof construction
Built tough to withstand the punishing marine environ-
ment, the IC-M2A meets JIS waterproof specification
grade 7 while using BP-223 or BP-224.
ꢀ Dual watch and tri-watch functions
Convenient functions which allow you to monitor the dis-
tress channel (Ch 16) while receiving a channel of your
choice—dual watch; or monitor the distress channel and
another channel while receiving a channel of your
choice—tri-watch.
IMPORTANT
READ ALL INSTRUCTIONS carefully and com-
pletely before using the transceiver.
SAVE THIS INSTRUCTION MANUAL—This in-
struction manual contains important operating instructions for
the IC-M2A.
ꢀ Large, easy-to-read LCD
With dimensions of 24(H) × 35(W) mm, the IC-M2A’s func-
tion display is easy to read and shows operating condi-
tions at a glance. Backlighting and contrast can be
adjusted to suit your preferences.
EXPLICIT DEFINITIONS
ꢀ Simple operation
WORD
RWARNING
CAUTION
NOTE
DEFINITION
Ergonomic design with a minimum number of switches
and controls provides simple intuitive operation.
Personal injury, fire hazard or electric shock
may occur.
Equipment damage may occur.
If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS
BE CAREFUL! The transceiver’s right-side panel will
RWARNING! NEVER connect the transceiver to an
AC outlet. This may pose a fire hazard or result in an electric
shock.
become hot when operating continuously for long periods.
BE CAREFUL! The IC-M2A employs waterproof con-
struction, which corresponds to JIS waterproof specification,
grade 7 (1 m; 3 ft depth for 30 min.). However, once the trans-
ceiver has been dropped, waterproofing cannot be guaran-
teed due to the fact that the transceiver may be cracked, or
the waterproof seal damaged, etc.
RWARNING! NEVER hold the transceiver so that the
antenna is very close to, or touching exposed parts of the
body, especially the face or eyes, while transmitting. The
transceiver will perform best if the microphone is 5 to 10 cm
(2 to 4 inches) away from the lips and the transceiver is verti-
cal.
MAKE SURE the flexible antenna and battery pack are
securely attached to the transceiver, and that the antenna and
battery pack are dry before attachment. Exposing the inside
of the transceiver to water will result in serious damage to the
transceiver.
NEVER connect the transceiver to a power source other
than the BP-223 or BP-224. Such a connection will ruin the
transceiver.
AVOID using or placing the transceiver in direct sunlight or
in areas with temperatures below –20°C (–4°F) or above
+60°C (+140°F).
For U.S.A. only
CAUTION: Changes or modifications to this device, not
expressly approved by Icom Inc., could void your authority to
operate this device under FCC regulations.
KEEP the transceiver out of the reach of children.
KEEP the transceiver at least 0.9 meter (3.0 ft) away from
your vessel’s magnetic navigation compass.
Icom, Icom Inc. and
are registered trademarks of Icom Incorporated
(Japan) in the United States, United Kingdom, Germany, France, Spain, Russia
and/or other countries.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SAFETY TRAINING INFORMATION ................................... i
IN CASE OF EMERGENCY ............................................... ii
RECOMMENDATION .......................................................... ii
FOREWORD ...................................................................... iii
IMPORTANT ....................................................................... iii
EXPLICIT DEFINITIONS .................................................... iii
FEATURES ......................................................................... iii
CAUTIONS ......................................................................... iv
TABLE OF CONTENTS ...................................................... v
I Operation ................................................................... 10
5 SCAN OPERATION ................................................ 11–12
I Scan types ................................................................. 11
I Setting tag channels .................................................. 12
I Starting a scan .......................................................... 12
6 SET MODE ............................................................. 13–16
I SET mode programming ........................................... 13
I SET mode items ........................................................ 13
1 OPERATING RULES ...................................................... 1
7 BATTERY CHARGING ........................................... 17–19
I Battery charging ........................................................ 17
I Battery cautions ......................................................... 17
I Installing batteries in the battery case ....................... 18
I Optional battery chargers .......................................... 19
2 PANEL DESCRIPTION ............................................... 2–5
I Front, top and side panels............................................ 2
I Function display .......................................................... 4
3 BASIC OPERATION ................................................... 6–9
I Channel selection ........................................................ 6
I Lock function ............................................................... 7
I Adjusting the squelch level .......................................... 7
I Receiving and transmitting .......................................... 8
I Call channel programming .......................................... 9
I Automatic backlighting ................................................ 9
8 SUPPLIED ACCESSORIES AND ATTACHMENTS 20–22
9 TROUBLESHOOTING .................................................. 23
10 CHANNEL LIST ........................................................... 24
11 SPECIFICATIONS AND OPTIONS .............................25
I Specifications ........................................................... 25
I Options ..................................................................... 25
4 DUALWATCH/TRI-WATCH .......................................... 10
I Description ................................................................ 10
v
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING RULES
1
(2) OPERATOR’S LICENSE
D Priorities
A restricted Radiotelephone Operator Permit is the license
most often held by small vessel radio operators when a radio
is not required for safety purposes.
• Read all rules and regulations pertaining to priorities and
keep an up-to-date copy handy. Safety and distress calls
take priority over all others.
The Restricted Radiotelephone Operator Permit must be
posted near the transceiver or be kept with the operator. Only
a licensed radio operator may operate a transceiver.
• You must monitor Channel 16 when you are not operating
on another channel.
• False or fraudulent distress calls are prohibited under law.
However, non-licensed individuals may talk over a transceiver
if a licensed operator starts, supervises, ends the call and
makes the necessary log entries.
D Privacy
• Information overheard but not intended for you cannot law-
fully be used in any way.
A current copy of the applicable government rules and regu-
lations is only required to be on hand for vessels in which a
radio telephone is compulsory. However, even if you are not
required to have these on hand it is your responsibility to be
thoroughly acquainted with all pertinent rules and regulations.
• Indecent or profane language is prohibited.
D Radio licenses
(1) SHIP STATION LICENSE
When your craft is equipped with a VHF FM transceiver, you
must have a current radio station license before using the
transceiver. It is unlawful to operate a ship station which is not
licensed.
Inquire through your dealer or the appropriate government
agency for a Ship-Radiotelephone license. This license in-
cludes the call sign which is your craft’s identification for radio
purposes.
NOTE: Even though the IC-M2A is capable of operation
on VHF marine channels 3, 21, 23, 61, 64, 81, 82 and 83,
according to FCC regulations these simplex channels can-
not be lawfully used by the general public in USA waters.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL DESCRIPTION
2
I Front, top and side panels
q CHANNEL/WEATHER CHANNEL SWITCH
t TRANSMIT POWER/LOCK SWITCH
[H/L•LOCK]
[CH/WX•U/I/C]
• Selects and toggles the regular channels and
weather channel when pushed. (pgs. 6, 7)
• Selects high, middle or low power when
pushed. (p. 8)
• Toggles the lock function ON/OFF when
pushed for 1 sec. (p. 7)
• Selects one of 3 regular channels in se-
o
quence when pushed for 1 sec. (p. 6)
- International, U.S.A. and Canadian channels
are available.
i
y DUALWATCH/TRI-WATCH SWITCH
[DW•TRI] (p. 10)
w CHANNEL UP/DOWN SWITCHES [Y]/[Z]
• Starts dualwatch when pushed momentarily.
• Starts tri-watch when pushed for 1 sec.
• Stops dualwatch/tri-watch when either is acti-
vated.
!
q
• Select an operating channel.
• Selects the SET mode condition of the item.
(p. 13)
• Set the squelch level in the squelch set mode.
(p. 7)
u SQUELCH SWITCH [SQL•MONI] (p. 7)
• Push this switch, then set the squelch level
with [Y]/[Z].
e CHANNEL 16 SWITCH [16•9]
• Selects Channel 16 when pushed. (p. 6)
• Selects the call channel when pushed for
1 sec.
• Manually opens the squelch for channel mon-
itoring when pushed for 1 sec.
u
• Enters call Channel write mode when the call
channel is selected and this switch is pushed
for 3 sec. (p. 9)
y
t
r
i ANTENNA (p. 20)
w
e
Connects the supplied antenna.
o VOLUME CONTROL [OFF/VOL]
r SCAN/TAG SWITCH [SCN•TAG] (p. 12)
• Starts and stops normal or priority scan.
• Sets and clears the displayed channel as a
tag (scanned) channel when pushed for
1 sec.
Turns power ON and adjusts the audio level.
! PTT SWITCH [PTT]
Push and hold to transmit; release to receive.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
2
PANEL DESCRIPTION
CAUTION!:
ï BATTERY CASE RELEASE SCREW
To remove the battery case:
When attaching or releasing a battery pack, make sure the
rubber seal is set in the groove of the battery pack/case
correctly. If the seal is not neatly in the groove it may be
damaged when attaching the battery pack/case.
Turn the screw counterclockwise, then pull the battery pack
in the direction of the arrow as shown below.
If the seal is damaged, waterproofing is not guaranteed.
To attach the battery case:
Insert the battery case in the IC-M2A completely, then turn
the screw clockwise.
NOTE:
NOTE: When removing or attaching the battery case, use a
coin or flat-head screwdriver to loosen or tighten the
bottom screw.
When attaching a battery pack/case, make sure dust etc.
does not adhere to the rubber seal. If dust etc. is on the seal
when attaching a battery pack/case, the water resistant may
be reduced.
Make sure both the rubber seal (purple) is set to the groove
correctly and dust etc. does not adhere to it.
Screw position
when removing battery
OPEN
Screw position
when attaching battery
Incorrect position
Correct position
Rubber seal
Groove
OPEN
Battery pack/case
Battery pack/case
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2
PANEL DESCRIPTION
I Function display
q TRANSMIT INDICATOR (p. 8)
Appears while transmitting.
w BUSY INDICATOR (p. 8)
Appears when receiving a signal or when the squelch
opens.
q w
e
r t
e TAG CHANNEL INDICATOR (p. 12)
y
Appears when a tag channel is selected.
u
i
!
r SCAN INDICATOR (p. 12)
Blinks while scanning.
o
t CALL CHANNEL INDICATOR (p. 6)
!
!
Appears when the call channel is selected.
!
!
y LOCK INDICATOR (p. 7)
Appears while the lock function is activated.
u WEATHER CHANNEL/WEATHER ALERT INDICATORS
• “WX” appears when the weather channel group is se-
lected. (p. 7)
!
!
• “ALT” appears while the weather alert function is acti-
vated; blinks when on alert tone is received.
i DUPLEX INDICATOR
Appears when a duplex channel is selected.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2
PANEL DESCRIPTION
o DUALWATCH/TRI-WATCH INDICATORS (p. 10)
“DUAL” appears during dualwatch; “TRI” appears during
tri-watch.
! CHANNEL GROUP INDICATOR (p. 6)
“U” appears when U.S.A.; “I” appears when International;
“C” appears when the Canadian channel group is se-
lected.
! SUB CHANNEL READOUT
• Indicates Channel 16 during priority scan.
• Indicates Channel 16 during dualwatch or tri-watch.
(p. 10)
! TRANSMIT POWER INDICATOR
• “LOW” appears when low power is selected. (p. 8)
• “LOW” blinks when switching forced low power mode be-
cause of a high temperature error or low voltage.
• “MID” appears when middle power is selected. (p. 8)
• No indicator appears when high power is selected.
• Indicates the SET mode item while in SET mode
! BATTERY INDICATOR
Indicates remaining battery power.
Indication
Charging
required battery
No
Battery level
Full
Middle
! SQUELCH LEVEL INDICATOR (p. 7)
Shows squelch level when set.
This indicator can be also used as an S/RF meter when the
S/RF meter indicator setting is ON. (p. 16)
! SQUELCH LEVEL ADJUSTING INDICATOR (p. 7)
Appears while adjusting the squelch level.
! CHANNEL NUMBER READOUT
• Indicates the selected operating channel number.
• In SET mode, indicates the selected condition.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
3
I Channel selection
D U.S.A., International and Canadian channels
There are 57 U.S.A., 57 International and 61 Canadian chan-
nels. These channel groups may be specified for the operat-
ing area.
D Channel 16
Channel 16 is the distress channel. It is used for establishing
initial contact with another station and for emergency
communications. Channel 16 is monitored during dualwatch
or tri-watch. While standing by you are required to monitor
Channel 16.
q Push [CH/WX] to select a regular channel.
- If a weather channel appears, push [CH/WX] again.
w Push [Y]/[Z] switches to select a channel.
- “DUP” appears for duplex channels.
9
Push
16
e To change the channel group, push [CH/WX•U/I/C] for
1 sec.
- U.S.A.,International and Canadian channels can be selected in
sequence.
D Channel 9 (Call channel)
Channel 9 is the leisure-use call channel. Each regular
channel group has a separate call channel. The call channel
is monitored during tri-watch. The call channels can be
programmed (p. 9) and are used to store your most often-
used channels in each channel group for quick recall.
• Push [16•9] for 1 sec. to select the call channel for the
selected channel group.
Push for 1 sec.
U.S.A. channels
U/I/C
U/I/C
CH
/WX
CH
/WX
- “CALL” and call channel number
appear.
-
Each channel group can have its
own call channel when programmed.
U/I/C
CH
/WX
Canadian channels
International channels
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3
BASIC OPERATION
D Weather channels
I Adjusting the squelch level
The IC-M2A has a squelch even though there is no control
knob for it. In order to receive signals properly, as well as for
scan to function, the squelch must be adjusted to a suitable
level.
There are 10 weather channels. These are used for monitor-
ing weather channels from the NOAA (National Oceano-
graphic and Atmospheric Administration) broadcasts.
The IC-M2A can detect a weather alert tone on the selected
weather channel while scanning. See the “SET mode items”
on p. 13.
q Push [CH/WX] to select a weather channel group.
w Push [Y]/[Z] to select a weather channel.
e Push [CH/WX] to return to the condition before selecting
weather channel group.
Appears durling squelch
level adjustment.
U/I/C
Push
CH
Each dot indicates the squelch level
(Level 10: Max. squelch level)
/WX
q Push [SQL•MONI], then adjust the squelch level with [Y]/[Z].
- “SQL” indicator and squelch level indicator appear.
- There are 11 squelch levels to choose from: 0 is completely
open; 10 is the maximum squelch level.
- When no keys are pushed for 5 sec., the transceiver returns to
normal condition.
w Push [SQL•MONI] again to return to normal condition.
I Lock function
This function electronically locks all keys, except [PTT],
[SQL•MONI] and [H/L•LOCK] to prevent accidental channel
changes and function access.
• Push [H/L•LOCK] for 1 sec. to turn the lock function ON and
OFF.
- Only [PTT], [H/L•LOCK] and [SQL•MONI] are functional.
Appears while the
lock function is used.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3
BASIC OPERATION
IMPORTANT: To maximize the readability of your trans-
mitted signal, pause a few sec. after pushing [PTT], hold
the microphone 5 to 10 cm (2 to 4 inches) from your
mouth and speak at a normal voice level.
I Receiving and transmitting
CAUTION: Transmitting without an antenna may
damage the transceiver.
NOTE: The transceiver has a power save function to con-
serve the battery power and cannot be turned OFF. The
power save function activates automatically when no sig-
nal is received for 5 sec.
q Rotate [OFF/VOL] clockwise to turn power ON.
- Use the squelch function to mute any audio noise if necessary.
Refer to the previous page for details.
w Push* [SQL•MONI] for 1 sec., and rotate volume to set
audio output level.
For U.S.A version: To prevent accidental prolonged
transmission, etc., the IC-M2A has a time-out timer func-
tion. This timer cuts a transmission OFF after 5 min. of
continuous transmission.
*According to Monitor action selection in SET mode (p. 14).
e Push [Y]/[Z] to select the desired channel.
- When receiving a signal, “BUSY” appears and audio is emitted
from the speaker.
(The S/RF meter appears while S/RF meter turned ON in SET
mode.)
- Further adjustment of [OFF/VOL] may be necessary at this point.
q Power ON
w Set volume
r Push [H/L] to select the output power if necessary.
- “LOW” appears when low power is selected; “MID” appears when
middle power is selected; no indicator appears when high power
is selected.
t Push to
transmit
- Choose low power to conserve battery power, choose high power
for longer distance communications.
y Release to
- Some channels are for low power only.
w Set squelch
receive
t Push and hold [PTT] to transmit, then speak into the
level
microphone.
- “TX” appears.
(The S/RF meter appears while S/RF meter is turned ON in SET
mode.)
- Channel 70 cannot be used for transmission (for GMDSS use).
w Set squelch level
e Set channel
r Set output
power
y Release [PTT] to receive.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3
BASIC OPERATION
I Call channel programming
The call channel switch is used to select Channel 9 by de-
fault, however, you can program your most often-used chan-
nels in each channel group for quick recall.
r Push [Y]/[Z] to select the de-
sired channel.
q Push [CH/WX•U/I/C] for 1 sec. to
select the desired channel
group (USA, INT, CAN) to be
programmed.
t Push [16•9] to program the dis-
played channel as the call chan-
nel.
- The call channel number and chan-
nel group stop flashing.
w Push [16•9] for 1 sec. to select
the call channel of the selected
channel group.
- “CALL” and call channel number
appear.
I Automatic backlighting
This function is convenient for nighttime operation. The auto-
matic backlighting can be deactivated in SET mode. (p. 15)
e Push [16•9] again for 3 sec.
(until long beep changes to 2
short beeps) to enter call chan-
nel programming condition.
- Call channel number and channel
group to be programmed flash.
• Push any key except for [PTT] to turn the backlighting ON.
- The backlighting is automatically turned OFF after 5 sec. of in-
activity.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DUALWATCH/TRI-WATCH
4
I Description
Dualwatch monitors Channel 16 while you are receiving an-
other channel; tri-watch monitors Channel 16 and the call
channel while receiving another channel.
I Operation
q Select the desired operating channel.
w Push [DW•TRI] momentarily to start dualwatch; push
[DW•TRI] for 1 sec. to start tri-watch.
- “DUAL” flashes during dualwatch; “TRI” flashes during tri-watch.
- Beep tones sound when a signal is received on Channel 16.
- Tri-watch becomes dualwatch when receiving a signal on the call
channel.
DUALWATCH/TRI-WATCH SIMULATION
e To cancel dualwatch/tri-watch, push [DW•TRI] again.
Call channel
[Example]: Operating tri-watch on INT Channel 07.
Push for 1 sec.
Tri-watch starts.
TRI
DW
Dualwatch
Tri-watch
Signal is received
on call channel.
• If a signal is received on Channel 16, dualwatch/tri-watch pauses
on Channel 16 until the signal disappears.
• If a signal is received on the call channel during tri-watch, tri-
watch becomes dualwatch until the signal disappears.
• To transmit on the selected channel during dualwatch/tri-watch,
push and hold [PTT].
Signal received on
Channel 16 takes
priority.
Tri-watch resumes
after the signal
disappears.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SCAN OPERATION
5
I Scan types
Scanning is an efficient way to locate signals quickly over a
wide frequency range. The transceiver has a priority scan and
a normal scan.
Set the tag channels (channels to be scanned) before scan-
ning. Clear the tag channels which inconveniently stop scan-
ning, such as those used for digital communications.
In addition, weather alert functions are available for standby
convenience. (p. 13)
NOTE: Choose priority or normal scan in SET mode. (p. 14)
PRIORITY SCAN
NORMAL SCAN
CH 01
CH 02
CH 01
CH 02
WX*
CH 03
WX*
CH 16
CH 03
CH 05
CH 04
CH 05
CH 04
* Previously selected weather channel
when weather alert function is ON.
* Previously selected weather channel
when weather alert function is ON.
Priority scan searches through all tag channels in se-
quence while monitoring Channel 16. When a signal is de-
tected on Channel 16, scan pauses until the signal
disappears; when a signal is detected on a channel other
than Channel 16, scan becomes dualwatch until the signal
disappears.
Normal scan, like priority scan, searches through all tag
channels in sequence. However, unlike priority scan, Chan-
nel 16 is not checked unless Channel 16 is set as a tag
channel.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5
SCAN OPERATION
I Setting tag channels
I Starting a scan
For more efficient scanning, add desired channels as tag
channels or clear tag channels for unwanted channels. Chan-
nels set as non-tag channels will be skipped during scanning.
Tag channels can be assigned to each channel group (USA,
INT, CAN) independently.
Set scan type, weather alert function and scan resume timer
in advance using SET mode. (pgs. 13, 14)
q Select the desired channel group (USA, INT, CAN) by
pushing [CH/WX•U/I/C] for 1 sec., if desired.
- When the weather alert function is in use, select the desired
weather channel with [CH/WX] and the [Y]/[Z].
q Select the desired channel group (USA, INT, CAN) by
pushing [CH/WX•U/I/C] for 1 sec., if desired.
w Select the desired channel to set as a tag channel.
e Push [SCN•TAG] for 1 sec. to set the displayed channel as
w Push [SCN•TAG] to start priority or normal scan.
- “SCAN” blinks in the function display.
- “16” appears during priority scan.
- When a signal is detected, scan pauses until the signal disap-
pears or resumes after pausing 5 sec. according to SET mode
setting. (Channel 16 is still monitored during priority scan.)
- Push [Y]/[Z] to check tag channels, to change the scanning di-
rection or resume the scan manually.
a tag channel.
- “TAG” appears in the function display.
r To cancel the tag channel setting, push [SCN•TAG] for 1
sec.
- “TAG” disappears.
e To stop the scan, push [SCN•TAG].
- “SCAN” disappears.
• Clearing all tag channels in the selected channel group
While pushing [SCN•TAG], turn the power ON to clear all
tag channels in the channel group.
- Pushing [PTT], [16•9], [CH/WX] or [DW•TRI] also stops the scan.
Scan pauses when receiving a
signal and audio is emitted.
[Example]: Starting a normal scan.
Scan starts.
Push
Push
TAG
TAG
SCN
SCN
to stop the scan.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SET MODE
6
I SET mode programming
I SET mode items
D Beep tone “bP”
SET mode is used to change the conditions of 12 transceiver
functions: beep tone, weather alert, scan type, scan resume
timer, auto scan, monitor switch, automatic backlighting, LCD
contrast, auto power save, self check, battery voltage and
S/RF meter functions.
You can select silent operation by turning beep tones OFF or
you can have confirmation beeps sound at the push of a
switch by turning beep tones ON.
• AUTO (At): Beep tone is linked with volume tone.
• 1–10: Beep tone scale is set from 1–10 scale (Max. is 10).
q Turn power OFF.
w While pushing [SQL•MONI], turn power ON and continue
pushing [SQL•MONI] until “bP” appears.
e Release [SQL•MONI].
r Push [Y]/[Z] to select the desired condition of the item.
t Push [SQL•MONI] to select the desired item, if necessary.
y To exit SET mode, turn the power OFF, then ON again, or
push [16•9].
Beep tone AUTO (default)
D Weather alert function “AL”
NOAA broadcast stations transmit weather alert tones before
important weather announcements. When the weather alert
function is turned ON, the transceiver detects the alert, the
“ALT” indicator blinks and sounds a beep tone until the trans-
ceiver is operated. The previously selected (used) weather
channel is checked periodically during standby or while scan-
SET MODE CONSTRUCTION
Scan
type
Battery
voltage
S/RF
meter
Weather
alert
Beep tone
ning.
Starting item
• “ALT” appears when the function is set ON.
Scan resume
timer
Self
check
MONI
SQL
Push
Automatic
backlighting
Monitor
switch
Auto
scan
LCD
contrast
Auto
power save
Weather alert function OFF (default) Weather alert function ON
13
Download from Www.Somanuals.com. All Manuals Search And Download.
6
SET MODE
D Priority scan function “Pr”
D Auto scan function “AS”
The transceiver has 2 scan types. Normal scan and priority
scan. Normal scan searches all tag channels in the selected
channel group. Priority scan searches all tag channels in se-
quence while monitoring Channel 16.
While in standby, this function automatically starts the desired
scan (normal or priority scan) 30 sec. after operation.
• Scan indicator blinks while scanning.
Auto scan OFF (default)
Normal scan (default)
D Monitor action selection “Sq”
The monitor function cuts off the squelch function temporarily.
This selection contains PUSH or HOLD settings as shown
below.
• PUSH (Pu): After pushing the [SQL•MONI] for 1 sec., the
squelch function is cut off until [SQL•MONI] is
released. (default)
• HOLD (Ho): After pushing the [SQL•MONI] for 1 sec., the
squelch function is cut off continuously until
another key is pushed.
D Scan resume timer “St”
The scan resume timer can be selected as a pause (OFF) or
timer scan (ON). When OFF is selected, the scan pauses
until a received signal disappears. When ON is selected, the
scan pauses for 5 sec. after receiving a signal and then re-
sumes even if the signal is still being received.
Scan timer OFF (default)
Monitor switch PUSH (default)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
6
SET MODE
D Automatic backlighting “bL”
D Auto power save function “PS”
The power save function reduces current drain by deactivat-
ing the receiver circuit for preset intervals.
This function is convenient for nighttime operation. The auto-
matic backlighting turns the backlighting ON when pushing
any key except for [PTT].
•
The backlighting is automatically turned OFF after 5 sec. of inactivity.
Auto power save ON (default)
D Self check function “SC”
The self check function checks transceiver conditions by it-
self, and informs you in case a problem is found. The follow-
ing items are checked after the power is turned ON, then it
switches to operation mode.
• Temperature (Outside of –20°C to +60°C; –4°F to +140°F)
• Connected battery voltage
Automatic backlighting ON (default)
D LCD contrast selection “LC”
The contrast of the LCD can be adjusted from 4 levels.
• 1 (low contrast) – 4 (high contrast); 3 (default)
• Water intrusion
When error messages as shown
below are displayed, see trouble
Self check OFF (default)
shooting for advice (p. 23).
Error messages
LCD contrast (default)
Temperature error Battery voltage error Water intrusion error
15
Download from Www.Somanuals.com. All Manuals Search And Download.
6
SET MODE
D Battery voltage indicator “bt”
SET MODE LIST
Indication
This function contains display or non-display settings of the
voltage of the connected battery pack when the power is ON.
• The voltage of the connected battery pack is displayed for 2 sec.
after power is turned ON.
Function
Switch
OFF / Auto* / 1 10
OFF* / ON
OFF* / ON
OFF* / ON
OFF* / ON
Push* / Hold
ON* / OFF
3* / 1 4
Beep tone
"bP"
Weather alert function
Scan type selection
"AL"
"Pr"
"St"
Scan resume timer
Battery voltage OFF (default)
Auto scan function
"AS"
"Sq"
"bL"
"LC"
"PS"
"SC"
"bt"
D S-meter/RF meter indicator “Sr”
This function contains display or non-display setting of the
S-meter/RF meter.
Monitor switch selection
Automatic backlighting
LCD contrast selection
Auto power save function
Self check function
ON* / OFF
OFF* / ON
OFF* / ON
S-meter/RF meter OFF (default)
Battery voltage indicator
S-meter/RF meter indicator
"Sr"
OFF* / ON
*default setting
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY CHARGING
7
I Battery charging
Prior to using the transceiver for the first time, the Ni-Cd bat-
I Battery cautions
NEVER incinerate used Ni-Cd batteries. Internal battery gas
teries must be fully charged for optimum life and operation.
may cause an explosion.
CAUTION: To avoid damage to the transceiver, turn it OFF
NEVER immerse batteries in water. If the battery case be-
comes wet, be sure to wipe it dry BEFORE attaching it to the
transceiver.
while charging.
• Recommended temperature range for charging:
+50°F to +104°F (+10°C to +40°C)
• Use the supplied AC adapter (BC-147A/E or BM-95V) only.
NEVER use other adapters.
NEVER short terminals of the battery case. Also, current may
flow into nearby metal objects so be careful when placing bat-
tery cases in handbags, etc.
NEVER connect DC power to the battery case when in-
stalling alkaline batteries. Such a connection will damage
the transceiver.
If your Ni-Cd batteries seem to have no capacity even after
being charged, completely discharge them by leaving the
power ON overnight. Then, fully charge the Ni-Cd batteries
again. If the batteries still do not retain a charge (or very little),
new batteries must be purchased.
D Recycling information (U.S.A. only)
The product that you have purchased contains a
rechargeable battery. The battery is recyclable. At
the end of its life, under various state and local
laws, it may be illegal to dispose of this battery
into the municipal waste stream. Call 1-800-822-8837 for bat-
tery recycling options in your area or contact your dealer.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
7
BATTERY CHARGING
ï Charging connections
I Installing batteries in the
q Attach the BC-150 to a flat surface, such as desk or cabin, etc., if
desired.
w Connect the AC adapter (BC-147A/E or BM-95V) as shown below.
e Insert the battery pack with/without the transceiver into the
charger.
battery case
(Not supplied with some versions)
When using a battery case attached to the transceiver, install
6 × AA(R6) size alkaline batteries as illustrated below.
• The charge indicator lights green.
r Charge the battery pack approx. 8 hours, depending on the re-
maining power condition.
q Remove the battery case from the transceiver.
w Install 6 × AA(R6) size alkaline batteries.
• Be sure to observe the correct polarity.
CAUTION: DO NOT charge BP-224 more than 12 hours.
Otherwise, BP-224 will be damaged. BP-224 must
be charged for 8–12 hours only.
CAUTION:
• When installing batteries, make sure they are all the
same brand, type and capacity. Also, do not mix new and
old batteries together.
• Keep battery contacts clean. It’s a good idea to clean bat-
tery terminals once a week.
IC-M2A
BP-224
Charge indicator
Lights green when
BP-224 (with/without
IC-M2A) is inserted.
Supplied screws
AC adapter
(BC-147A/E
or BM-95V)
BC-150
18
Download from Www.Somanuals.com. All Manuals Search And Download.
7
BATTERY CHARGING
I Optional battery chargers
D Rapid charging with the BC-119N+AD-103
The optional BC-119N provides rapid charging of battery
packs. The following are additionally required.
• AD-103
D Rapid charging with the BC-121N+AD-103
The optional BC-121N allows up to 6 battery packs to be
charged simultaneously. The following are additionally re-
quired.
• An AC adapter (may be supplied with BC-119N depending
on version).
• Six AD-103.
• An AC adapter (BC-124) or the DC power cable (OPC-656).
IC-M2A
BP-224
IC-M2A
BP-224
AD-103 charger
adapters are installed
in each slot.
AC adapter
(purchased
separately)
OPC-515L or
CP-17L
AD-103 charger
adapter is installed
in BC-119N.
AC adapter
(Not supplied with some
versions.)
DC power cable
(Connect with the DC power supply;
13.8 V/at least 7 A)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPPLIED ACCESSORIES AND ATTACHMENTS
8
D Supplied accessories
The following accessories are supplied:
D Flexible antenna
Qty. Connect the supplied flexible
antenna to the antenna con-
q Flexible antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 nector.
w Swivel belt clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
e Handstrap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
r Battery case (BP-223)*1 . . . . . . . . . . . . . . . . . . . . . . . . . .1
t Ni-Cd battery pack (BP-224) . . . . . . . . . . . . . . . . . . . . . . .1
y AC adapter (BC-147A/E or BM-95V)*2 . . . . . . . . . . . . . . .1
u Battery charger (BC-150) . . . . . . . . . . . . . . . . . . . . . . . . .1
i Screws for the BC-150 (M3.5 × 20) . . . . . . . . . . . . . . . . .2
*1 Not supplied with some versions.
CAUTION: Transmitting
without an antenna may
damage the transceiver.
*2 Depending on version.
D Handstrap
Slide the handstrap
through the loop on the
side of the transceiver as
illustrated at right. Facili-
tates carrying.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
8
SUPPLIED ACCESSORIES AND ATTACHMENTS
D Swivel belt clip
To attach:
q Slide the stopper into the plastic loop on the back of the
e Insert the stopper to the back of the belt clip.
transceiver.
w Clip the belt clip to a part of your belt.
Once the transceiver is locked in place, it will swivel 360 de-
grees.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
8
SUPPLIED ACCESSORIES AND ATTACHMENTS
To remove:
q Turn the transceiver upside down, and then lift to release
R
CAUTION!
the transceiver from the belt clip.
HOLD THE TRANSCEIVER TIGHTLY, WHEN ATTACH-
ING OR REMOVING THE TRANSCEIVER FROM THE
BELT CLIP.
If the transceiver is accidentally dropped and the swivel
belt clip’s stopper is scratched or damaged, the swivel
belt clip may not work properly.
w Release the belt clip.
e Push the top of the stopper towards the transceiver and out
at the same time, then push it downwards and free of the
plastic loop.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
9
PROBLEM
POSSIBLE CAUSE
• The battery is exhausted.
SOLUTION.
REF.
• Recharge the battery pack.
No power comes ON.
p. 17
• Bad connection to the battery pack.
• Check the connection to the transceiver.
p. 3
• Squelch level is too deep.
• Volume level is too low.
• Speaker has been exposed to water.
• Set squelch to the threshold point.
• Set [OFF/VOL] to a suitable level.
• Drain water from the speaker.
No sound comes from
the speaker.
p. 7
p. 8
—
Transmitting is impossi- • Some channels are for low power or re- • Change channels.
pgs. 2, 4
ble, or high power can ceive only.
not be selected.
• The battery is exhausted.
• The output power is set to low.
• Recharge the battery pack.
• Push [H/L] to select high power.
p. 17
p. 2
The display channel • Lock function is activated.
• Push [H/L•LOCK] for 1 sec. to cancel the p. 2
cannot be changed.
function.
Scan does not start.
No beeps sound.
• “TAG” channels are not programmed.
• Beep tones are turned OFF.
• Set the desired channels as “TAG” channels. p. 12
• Set the beep tones to AUTO or 1–10 in SET p. 13
mode.
Self check error.
• Transceiver’s inside temperature is below • Leave the transceiver at room temperature
—
(Temperature error)
–20°C (–4°F) or above +60°C (+120°F).
for a while. Turn the power ON to check if the
internal temperature has returned to normal.
Self check error.
(Battery voltage error)
• The connected battery pack’s voltage is • Verify the battery voltage is correct.
more than 11 V.
—
—
Self check error.
(Water intrusion error)
• Water has entered the transceiver.
• Have the transceiver checked at your local
distributor or dealer to see whether the trans-
ceiver works properly or not.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANNEL LIST
10
Channel number Frequency (MHz)
Channel number Frequency (MHz)
USA INT CAN Transmit Receive
Channel number Frequency (MHz)
USA INT CAN Transmit Receive
Channel number Frequency (MHz)
USA INT CAN Transmit Receive
USA INT CAN Transmit Receive
85
85A
86
85
86
87
88
85 157.275 161.875
157.275 157.275
01
01 156.050 160.650
156.050 156.050
19A
20
19A 156.950 156.950
*
66
156.325 160.925
156.325 156.325
*
01A
20
21
22
23
157.000 161.600
157.000 157.000
66A 66A
*
20
66A
86 157.325 161.925
157.325 157.325
02
03
02 156.100 160.700
03 156.150 160.750
156.150 156.150
20A
67
68
69
70
71
72
73
74
77
78
67 156.375 156.375
68 156.425 156.425
69 156.475 156.475
67
68
69
70
71
72
73
74
86A
87
21 157.050 161.650
21A 157.050 157.050
157.100 161.700
87 157.375 161.975
157.375 157.375
03A
21A
22A
87A
88
04
05
156.200 160.800
Rx only
156.525
70
88 157.425 162.025
157.425 157.425
04A 156.200 156.200
156.250 160.850
22A 157.100 157.100
23 157.150 161.750
157.150 157.150
71 156.575 156.575
72 156.625 156.625
73 156.675 156.675
88A
05A
06
05A 156.250 156.250
06 156.300 156.300
156.350 160.950
21b Rx only 161.650
25b Rx only 161.850
28b Rx only 162.000
83b Rx only 161.775
23A
24
06
07
24
25
26
27
28
60
61
24 157.200 161.800
25 157.250 161.850
26 157.300 161.900
27 157.350 161.950
28 157.400 162.000
60 156.025 160.625
156.075 160.675
74 156.725 156.725
*
*
25
156.875 156.875
156.925 161.525
77
77
07A
08
09
10
11
07A 156.350 156.350
08 156.400 156.400
09 156.450 156.450
10 156.500 156.500
11 156.550 156.550
26
08
09
10
11
12
13
14
78A
79A
80A
81A
82A
78A 156.925 156.925
156.975 161.575
27
Frequency (MHz)
79
80
81
82
83
84
28
WX channel
Transmit Receive
79A 156.975 156.975
157.025 161.625
1
2
RX only
RX only
RX only
RX only
RX only
RX only
RX only
RX only
RX only
RX only
162.550
162.400
162.475
162.425
162.450
162.500
162.525
161.650
161.775
163.275
12
12 156.600 156.600
*
61A
61A 156.075 156.075
156.125 160.725
80A 157.025 157.025
157.075 161.675
*
156.650 156.650
3
13
13
62
63
64
65
14
14 156.700 156.700
*
4
62A 156.125 156.125
156.175 160.775
81A 157.075 157.075
157.125 161.725
*
*
156.750 156.750
5
15
15
16
17
18
15
16
16 156.800 156.800
*
6
82A 157.125 157.125
83 157.175 161.775
83A 157.175 157.175
84 157.225 161.825
157.225 157.225
63A
64A
156.175 156.175
*
156.850 156.850
156.900 161.500
7
17
17
64 156.225 160.825
64A 156.225 156.225
156.275 160.875
83A
84
8
18A
18A 156.900 156.900
156.950 161.550
9
84A
19
10
65A 65A 65A 156.275 156.275
*Low power only.
NOTE: Simplex channels 3, 21, 23, 61, 64, 81, 82 and 83 CANNOT
be lawfully used by the general public in USA waters.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS AND OPTIONS
11
I Specifications
I Options
• GENERAL
D BATTERY CASE AND PACK
• BP-223 BATTERY CASE
Frequency coverage
: Transmit 156.025–157.425 MHz
Receive 156.050–163.275 MHz
Battery case for 6 × AA (R6) alkaline cells. The same as supplied
with the transceiver depending on versions.
• BP-224 Ni-Cd BATTERY PACK
Mode
Channel spacing
: FM (16K0G3E)
: 25 kHz
Current drain (at 7.5 V DC) : TX High (5 W)
1.5 A typical.
200 mA typical
20 mA typical
7.2 V/750 mAh Ni-Cd battery pack. The same as supplied with the
transceiver depending on versions.
Max. audio
Power save
Frequency stability
: 10 ppm (–20°C to +60°C)
Useable temperature range : –20°C to +60°C; –4°F to +140°F
D CHARGERS
• BC-119N DESKTOP CHARGER + AD-103 CHARGER ADAPTER
+ BC-145 AC ADAPTER
For rapid charging of battery packs. An AC adapter is supplied with
the charger. Charging time: approx. 1.5 to 2 hours
• BC-121N MULTI-CHARGER + AD-103 CHARGER ADAPTER (6 pcs.)
+ BC-124 AC ADAPTER
Dimensions
(Projections not included)
Weight (approx.; with BP-224) : 360g (12.7 oz)
: 61 (W) × 135(H) × 41(D) mm
213⁄32(W) × 55⁄16(H) × 15⁄8(D) inch
• TRANSMITTER
Output power (at 7.5 V DC) : 5 W (Hi), 3 W (Mid) and 1 W (Low)
Modulation system
:
Variable reactance frequency modulation
For rapid charging of up to 6 battery packs (six AD-103’s are re-
quired) simultaneously. An AC adapter may be supplied depending
on version. Charging time: approx. 1.5 to 2 hours.
• BC-150 DESKTOP CHARGER + BC-147A/E or BM-95V AC ADAPTER
Used for regular charging of battery pack. The same as supplied
with the transceiver. Charging time: approx. 8 hours
Max. frequency deviation
Audio harmonics distortion : Less than 10 % (at 60 % mod.)
Spurious emissions
: 5 kHz
: Less than –65 dBc
• RECEIVER
Receive system
Sensitivity (12 dB SINAD)
Squelch sensitivity
Intermodulation rejection ratio : 70 dB typical
Spurious response rejection ratio : 70 dB typical
Adjacent channel selectivity : 70 dB typical
: Double-conversion superheterodyne
: 0.25 µV typical
: Less than 0.35 µV (at threshold)
D BELT CLIPS
• MB-68 BELT CLIP
• MB-74 BELT CLIP
Ham and noise ratio
Audio output power
: More than 40 dB
: 0.35 W typical at 10% distortion with an
8 Ω load
Exclusive alligator-type belt clip.
• MB-87 SWIVEL BELT CLIP
Belt clip for swivel type. The same as supplied with the transceiver.
All stated specifications are subject to change without notice or obligation.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Count on us!
A-6113H-1EX-q
Printed in Japan
© 2001, 2002 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|