McPC-Gigabit
(PCI Version)
Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
FCC Radio Frequency Interference Statement ....................................................ii
Warranty............................................................................................................ii
About the McPC-Gigabit ....................................................................................1
AutoCross ..........................................................................................................1
LED Indicators....................................................................................................2
Specifications.....................................................................................................2
IMC Networks Technical Support.......................................................................2
Fiber Optic Cleaning Guidelines.........................................................................2
Safety Certifications............................................................................................4
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
About the McPC-Gigabit
The McPC-Gigabit is a low-cost, IEEE 802.3 single-conversion, PC Card media
converter that converts 1000Base-TX twisted pair to 1000Base-SX multi-mode or
1000Base-LX single-mode fiber. The McPC-Gigabit is available with one RJ-45
connector for the twisted pair port and a SC connector for the fiber port.
The McPC-Gigabit is also available for single-strand which allows two individual
channels to share one strand of fiber; Full-Duplex data travels on different
wavelengths— 1310 nm and 1550 nm.
The McPC-Gigabit can be mounted into any PC with a standard PCI and includes
diagnostic LEDs for each port.
Installing the McPC-Gigabit
Offering plug-and-play operation, the McPC-Gigabit comes ready to install, utilizing
power from the PC’s motherboard. To install the McPC-Gigabit:
1. Turn off the PC
2. Remove its cover
3. Find an empty PCI slot
4. Align the McPC-Gigabit in the slot
5. Screw the McPC-Gigabit into the computer casing’s bracket
6. Make sure the McPC-Gigabit does not extend past the edge of the case
7. Attach the keyed mini-power connector to the McPC-Gigabit
8. Attach the male end of the “Y” connector to one of the computer’s standard size
power connectors
9. Replace the cover
10. Attach the cables between the McPC-Gigabit and the devices that will be
connected
AutoCross
Whether you are using crossover or straight-through CAT5 twisted pair cabling,
McPC-Gigabit will support both types of connections with AutoCross, a feature which
automatically selects between a crossover workstation or Pass-Through connection
depending on the connected device.
FX
TX
1
Download from Www.Somanuals.com. All Manuals Search And Download.
LED Indicators
Each McPC-Gigabit includes two LEDs, located on the RJ-45 connector.
LED functions are as follows:
FX LNK/ACT
TX LNK/ACT
Glows green when a link is established on the fiber port; blinks
green when activity is detected on the fiber port.
Glows amber when a link is established on the copper port; blinks
amber when activity is detected on the copper port.
Specifications
Environmental
Operating Temperature
+32° to +104° F (0° to +40° C)
Storage Temperature
-4° to +158° F (-20° to +70° C)
Humidity:
5 - 95% (non-condensing)
Input Specifications
0.7A @ 5V DC
IMC Networks Technical Support
Tel: (949) 465-3000 or (800) 624-1070 (in the U.S. and Canada);
+32-16-550880 (Europe)
Fax: (949) 465-3020
E-Mail: [email protected]
Web: www.imcnetworks.com
Fiber Optic Cleaning Guidelines
Fiber Optic transmitters and receivers are extremely susceptible to contamination by
particles of dirt or dust, which can obstruct the optic path and cause performance
degradation. Good system performance requires clean optics and connector ferrules.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Use fiber patch cords (or connectors, if you terminate your own fiber) only from
a reputable supplier; low-quality components can cause many hard-to-diagnose
problems in an installation.
2. Dust caps are installed at IMC Networks to ensure factory-clean optical devices.
These protective caps should not be removed until the moment of connecting
the fiber cable to the device. Should it be necessary to disconnect the fiber
device, reinstall the protective dust caps.
3. Store spare caps in a dust-free environment such as a sealed plastic bag or box
so that when reinstalled they do not introduce any contamination to the optics.
4. If you suspect that the optics have been contaminated, alternate between
blasting with clean, dry, compressed air and flushing with methanol to remove
particles of dirt.
Electrostatic Discharge Precautions
Electrostatic discharge (ESD) can cause damage to any product, add-in modules or
stand alone units, containing electronic components. Always observe the following
precautions when installing or handling these kinds of products
1. Do not remove unit from its protective packaging until ready to install.
2. Wear an ESD wrist grounding strap before handling any module or component.
If the wrist strap is not available, maintain grounded contact with the system unit
throughout any procedure requiring ESD protection.
3. Hold the units by the edges; do not touch the electronic components or gold
connectors.
4. After removal, always place the boards on a grounded, static-free surface, ESD
pad or in a proper ESD bag. Do not slide the modules or stand alone units over
any surface.
WARNING! Integrated circuits and fiber optic components are
extremely susceptible to electrostatic discharge damage. Do not
handle these components directly unless you are a qualified service
technician and use tools and techniques that conform to accepted
industry practices.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Certifications
CE: The products described herein comply with the Council Directive on
Electromagnetic Compatibility (2004/108/EC). For further details, contact IMC
Networks.
Class 1 Laser product, Luokan 1 Laserlaite,
Laser Klasse 1, Appareil A’Laser de Classe 1
European Directive 2002/96/EC (WEEE) requires that any equipment that bears this
symbol on product or packaging must not be disposed of with unsorted municipal
waste. This symbol indicates that the equipment should be disposed of separately
from regular household waste. It is the consumer’s responsibility to dispose of this
and all equipment so marked through designated collection facilities appointed by
government or local authorities. Following these steps through proper disposal and
recycling will help prevent potential negative consequences to the environment and
human health. For more detailed information about proper disposal, please contact
local authorities, waste disposal services, or the point of purchase for this equipment.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
19772 Pauling • Foothill Ranch, CA 92610-2611 USA
TEL: (949) 465-3000 • FAX: (949) 465-3020
© 2010 IMC Networks. All rights reserved.
The information in this document is subject to change without notice. IMC Networks assumes no responsibility for any
errors that may appear in this document. McPC-Gigabit is a trademark of IMC Networks. Other brands or product names
may be trademarks and are the property of their respective companies.
Document Number 55-80900-00 B1
February 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
|