CD Duplicator
CoolCopy Series
User’s Manual
CoolCopy1AL(CD-Backup)
CoolCopy 3
CoolCopy 7
Download from Www.Somanuals.com. All Manuals Search And Download.
4.11.6 Auto Verify ...........................................................................22
4.11.7 Auto Compare ......................................................................22
4.11.8 Auto Prescan .......................................................................22
4.11.9 Eject Disc ............................................................................22
4.11.10 Burn on The Fly ................................................................23
4.11.11 Burn Mode ........................................................................23
4.11.12 Button Sound ....................................................................23
4.11.13 Device Info ....................................................................…24
4.11.14 System Info .......................................................................24
4.11.15 Quick Erase ......................................................................25
4.11.16 Full Erase ..........................................................................25
4.12 Adv Setup...................................................................................25
4.12.1 UnderRun Protect ...............................................….............25
4.12.2 Overburn ...............................................................…...........26
4.12.3 Read Error Skip............... ..................................…..…... ...26
4.12.4 Format Hard Disk ....................................................….........26
4.12.5 Verify HDD ...............................…..................................…...26
4.12.6 Burn-in.................................................…...…........................27
4.12.7 Update Firmware..........................................................….....27
4.12.8 Compare Firmware .......................................................…....28
4.12.9 H/W Diagnostic ...............................................................…..28
4.12.10 Load Default ..................................................................….28
Chapter 5 Troubleshooting .........................................................29
3
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Introduction
1.1 Overview
People who want to create multiple copies of their CDs usually take a long time to do so. They
might not have enough CD+RW drives or they might be using their computers for some other
important tasks. The duplication process noticeably slows down a computer during the burn
process. Rather than sit at the computer for hours duplicating discs one at a time, it is much more
efficient to use a CoolCopy CD duplication system.
The Coolcopy CD Duplicator system is a standalone duplicator and does not need to be
connected to a computer. It can duplicate discs accurately and quickly. With its multi-function
LCD panel, Coolcopy CD Duplicator is easy for any user to operate. It is a cost-efficient CD-R
duplicator for audio, data, and video applications. The simple control panel is designed to provide
copy mode selection and copy operation.
1.2 Features
•
•
Standalone IDE to IDE CD Copy controller
2(Coolcopy1AL(CD-Backup)) / 4(Coolcopy3) / 8(Coolcopy7) / 16(Coolcopy14)
independent IDE channel
•
•
•
•
•
•
•
Self system diagnostics when power on
Supports Hard Drive image
Auto format detection
User friendly interface with message rich LCD display
Fast copies supports high speed CD-RW writing mode
Easy operation without software and training are required
Firmware upgrade via CD-ROM
1.3 Specification
Power requirement – voltage:
Current:
5VB+/- 5%
0.5A Max.
Environment -
Temperature
Operating
Storage
0˚ C to 70˚ C
-20˚ C to 85˚ C
Humidity -
15% to 90%
Models:
Length:
Width:
Coolcopy3/coolcopy7
200 mm
Dimensions -
146.2 mm
Height:
42 mm
Connectors -
40-pin internal IDE connector
Cable (Optional) - Using ATA-66 (*Cable of length do not use longer than 46cm)
CD Format -
CD-ROM (Mode1 & Mode2), CD-ROM/XA (Mode2 form1 & form2), CD-DA,
Mixed-Mode, Video CD, CD-I, Karaoke CD, Photo CD (Single & Multi-
session), CD-Extra, HFS, CD Bridge, ISO9660, CD-R, and CD-RW
Writing mode -
Auto Detect (DAO, TAO)
4
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported CD-ROM Drives* - EPO, TEAC
Supported CD-RW Drives* - Plextor, TEAC, Lite-On, Asus, SONY
Chapter 2 Installation Procedure
When you receive the Coolcopy CD Duplicator, the package could be packaged in the following
ways: controller only, whole duplicator without writer installed, and a complete duplication system.
2.1 Controller only
1. Before the installation, please prepare the necessary devices as following:
•
•
•
•
•
CD-ROM drive
CD-R/RW drive
IDE case (2~10-bay chassis suggested).
Hard drive and mobile rack (IDE-bus hard drive-Option)
Switching power supply (300W suggested).
2. After the preparation as above and make sure that:
All IDE devices must be in master mode.
•
2.2 Whole duplicator without writer installed
•
•
Unpack the package of the duplicators.
Prepare the CD-R/RW writers according to the recommendation list. Please check with
the supplier about compatibility issues with unlisted CD-R/RW drives.
Assemble the duplicator according to your need.
•
•
Make sure that the voltage setting is correct.
2.3 Completed duplication system
•
•
•
•
Take the duplication system out of the package.
Check the entire unit to see if there are any problems.
Make sure that the voltage setting is correct.
The hard drive is optional.
Hardware Connection of CoolCopy1AL (CD-Backup) without a HDD
CoolCopy1AL (CD-Backup)
Power
5
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Connection with Hard Drive for Coolcopy3
Coolcopy 3
Power
When the system connects with the hard drive, the hard drive must connect on the IDE 0 port
with the “Master” setting and the CD-ROM must set at “Slave”.
Hardware Connection without Hard Drive for Coolcopy3
Coolcopy 3
Power
6
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Connection with Hard Drive for Coolcopy7
Coolcopy 7
CD-Rom/HDD
Power
7
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
When the system has a hard drive connected, the hard drive must connect on IDE 0 port with
“Master” setting and the CD-ROM must set at “Slave.”
Hardware Connection without Hard Drive for Coolcopy7
Coolcopy 7
Power
8
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Key Functions and Operating Instruction
1. LCD Display Panel: Display main functions and all messages.
2. Scroll up through menus or functions.
3. Scroll down through menus or functions.
4. Execute the function which you select.
5. Cancel the function which you select.
After turning the power on, the Coolcopy CD Duplicator will execute a self test for a few seconds.
After the self testing procedure runs, the LCD will show:
1.
2.
Coolcopy3:
Coolcopy7:
CD Duplicator
1-3 ver: 1.10B
CD Duplicator
1-7 ver: 1.10T
Initialize SDRAM.....
3.
4.
Detect Drives.....
1. Copy
Two main operation procedures
If you install a 3.5” hard disc, the operation procedures is as follows:
1. With hard drive installed
•
Once duplicator detects a hard disc, it will ask if you want to format or not. A 10GB hard
disc can be divided into 10 partitions.
•
•
•
Use the Select Source to set the hard drive as the target source.
Then select which partition to store the data in function 9 “Image.”
If there is no data stored in partition, insert a source CD into CD-ROM and use function 9-
01 Load to transmit data from CD into selected partition by pressing ENT. Different data
can be stored in different partitions.
•
Switch to the Copy function by pressing the arrow button. Insert blank CD-R or CDRW
discs into the CD writers. Press “ENT” button to start copying.
9
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
When a Copy completes, the passed (correctly copied) CD discs will be ejected
automatically. The default is to eject automatically, but this can be changed.
Failed discs will remain in writers. The default setting is keeping failed discs in the writers,
but this can be changed. Press the buttons on the drivers to take the failed CDs.
During operation do not press any button, interruption will harm the device. CDs will be
damaged.
2. Without a hard drive installed
If you don’t install a 3.5” hard disc, the operation procedures will be as follows:
•
•
Insert the master disc to CD-ROM.
Switch to the Copy function by pressing arrow button. Insert blank CD-R or CDRW disc
into all the CD writers. Press “ENT” button to start.
•
When Copy completes, the passed CDs will eject automatically. The default is to eject
automatically, but this can be changed.
•
Failed CDs will remain in the writers. The default setting is that failed CDs stay in the
writers, but you can change the setting. You need to press the “eject” buttons on the
writers to take the failed CDs.
ATA-66 Cable Layout:
Please identify two different kinds of cable before the hardware installation.
Chapter 4 Function
4.1 Copy
Use this function to copy data from a source CD directly onto blank CD discs. Before copying
make sure that the source CD is insertd into CD-ROM. If you have a HDD, make sure there is
data in your HDD partition. If you are not sure about the success of your duplication job, you can
use function 2, Test, to simulate the copying process first.
Select function 1. Put a source CD into CD-ROM and blank CD disks into CD writers. CD
rewriteable discs containing old data are usable, too.
Copying-24X 0%
650.0MB 74:00
LCD will show the process of copying
information as follows:
3. Test & Copy
OK: 03
When copying is completed, the LCD will display as
1. Copy
OK: 03
the following information:
Discs correctly copied will be ejected automatically
10
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
and failed ones will remain in the writers.
4.2 Test
Function 2 Test will simulate the copying process. When the simulation completes, the discs will
remain blank.
Press “ENT” button to start the disc simulation
or press “ESC” to exit.
2. Test
If you use CD rewriteable discs that contains data, the old
Data will be quickly erased before before simulation begins:
LCD will show the following testing
Testing-24X 0%
Information:
.
650.0MB 74:00
When the process is finished, the LCD will
show the following message:
2. Test
OK: 03
Stopping the test halfway does not affect the CD discs. However, if the CD rewriteable discs
contain important data, the information might be erased.
4.3 Test&Copy
Function 3 Test & Copy is to test first and then actually copy.
Select Function 3. Put a source CD into CD-ROM
3.Test & Copy
And blank CD discs into writers.
Press ENT to start simulation. LCD will show the
Information as follows:
Testing-24X 0%
After the tests finishes, actual copying will begin
as follows:
Copying-24X 0%
650.0MB 74:00
When the entire process finishes, the LCD will
show the information as follows:
4. Test & Copy
OK: 03
4.4 Verify
Function 4 Verify is to examine if the target CDs can be read correctly after copying.
11
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Press “ENT” button to verify. LCD will shows as
follows:
4. Verify
LCD will show verification information as
follows:
Verify--24X 0%
650.0MB 74:00
When the verification process is finished, the LCD
will display the result as follows:
4. Verify
OK: 03
4.5 Compare
Function 5 Compare is to make a comparison between the source and the target CDs after
copying.
Select Function 5. Put the source CD into CD-ROM
and the target CDs into CD writers.
5. Compare
Press ENT to compare. LCD will show the
comparison information as follows:
Compare-24X 0%
650.0MB 74:00
When comparison completes, LCD will show
as follows:
Compare OK: 3
Fail: 0 Diff: 0
Press “ENT” button to see the details of
source 1. If comparison is identical, LCD
will show the message as follows:
Src: 01 CD-ROM
Total: 650.0MB
If the compare result is identical, the LCD will
show as follows:
Src: 02 CD-RW
Identical
If comparison fails, LCD will show failure.
Compare OK: 2
Fail: 1 Diff: 0
Src: 01 CD-ROM
Total: 0 Bytes
Press “ENT” button to see comparison
information.
If the comparison fails, the LCD will show
failure. By pressing ENT twice, LCD will show
the contents of source 1 and those of source 2
do not match as follows:
Src: 02 CD-RW
TOC not match
12
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
4.6 Prescan
Use the prescan function to scan if the source CD can be read correctly and also to test the
reading speed.
Select function 6. Put the source CD
into CD-ROM.
6. Prescan
Press ENT to prescan, LCD will show the
scanning information as follows:
Scaning-24X 0%
650.0MB 74:00
If the master of the disc can read correctly,
the source CD has no problems. LCD
will show the following:
PreScan OK!
PreScan Fail!
If the master disc cannot be read correctly,
the LCD will show the message as follows:
4.7 Disc Info
Function 7, Disc Info, shows the basic information of the source CD.
Select Function 7. Insert source CD into CD-ROM.
7. Disc Info
Press the “ENT” button to show the disc information.
The LCD will show the total sessions and
tracks on the master disc.
Total 02 Sessions
Total 10 Tracks
Press the “ENT” button again, the LCD will show
the total time and capacity on the master disc
Total: 74:00
Total: 650 MB
Press the “ENT” button again and use arrow button
to select the session, LCD will show the
information contained in the session.
Session 01
Track 01 - 09
Press the “ENT” button again and use arrow button
to select the track. The LCD will then show what
information is contained on the track.
Track 01
AUDIO 03:54
4.8 Select Source
Function 8 Select Source will let you select the data on CD-ROM, CD writers or HDD as the
source from which you intend to copy.
13
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Select Source
Select function 8.
Press ENT and then use arrow button to select the
source.
Src: CD-ROM
01 IDE0 Slave
After selecting source, press ENT and LCD will
show the following:
CD-ROM selected!
Note: Suppose you select HDD as the source and try to copy from one of its partitions, but the
partition contains no data. An error message will then appear on your LCD. From here, you can
switch to another partition that contains no data or use function 9 Image to load the data into the
chosen partition first.
4.9 Image
Function 9, Image, is only valid when you have installed a hard drive.
Select function 9. Press ENT.
9. Image
4.9.1 Load
Insert the master CD disc into the CD-ROM or any one of the CD writers, the duplicator
will detect and analyze the master CD.
Here the Load function will allow you to load data
from CD-ROM or any CD writer into the current
partition of the hard disc. P:A means Partition A.
9-01.Image P: A
Load
Press ENT to load. LCD will then show the loading
information.
Load- A -24X 0%
650.0MB 74:00
When the image has successfully loaded, the LCD
will show the following:
Image load OK
If there is an image file existing in current partition,
the system will ask whether you want to overwrite.
Use arrow button to make a “Yes” or “No” selection.
Image Exists
Overwrite?Yes
4.9.2 Delete Image
If you want to empty an image file stored in a particular partition, you can use the function Delete
Image to do so.
9-02. Image P: A
Select function by pressing arrow.
Delete Image in
Partition A?Yes
The system will ask if you are sure you want to delete.
Use arrow button to make “Yes” or “No” selection.
14
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
When the image is successfully deleted from the
hard drive, the LCD will show as follows:
Partition A:
Image is deleted
4.9.3 Image Info
This function shows the basic information of an image file stored in a particular partition.
Press ENT to show the disc information.
9-03.Image P: A
Image Info
The LCD will show the total sessions and tracks
in the partition.
Total 01 Sessions
Total 01 Tracks
Press ENT again. The LCD will show
the total time and capacity in the hard drive of
partition.
Total: 74:00
Press ENT again and use arrow button
to select the session. LCD will show the information in
the session.
Session 01
Track 01 - 01
Press ENT again and use arrow button
to select the track. LCD will show track
information.
Track 01
DATA 650.0MB
4.9.4 Compare Image
Use this function to compare the contents of the source CD and those of the image file in the
partition. First select the function by pressing the arrow.
9-04. Image P: A
Compare Image
Press ENT and LCD will show the comparison
information as follows:
LCD will show the following screen:
Comp-A-24X 0%
650.0MB 74:00
When the process is finished, the LCD will display
the following message:
Compare OK: 1
Press ENT to view the comparison details.
Src: 01 CD-ROM
Total: 650.0MB
Tgt: 00 HDD P:A
Identical
If the comparison is identical, the LCD will
show the following message:
15
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
If comparison fails, LCD will show the number of discs
failed and succeeded.
Compare OK: 0
Fail: 1 Diff: 0
Press ENT to see the comparison
information.
Src: 01 CD-ROM
Total: 0 Bytes
If the comparison fails, the LCD will show
the reason as follows:
Src: 02 CD-RW
TOC not match
4.9.5 Select Partition
This function is to select a partition in the hard disc.
Press ENT button to change the setting.
9-05.Image P: A
Select Image
After installing a hard disc, duplicator will format it automatically. Each partition occupies 1GB.
The number of partitions is dependent on the hard disc’s capacity. The partitions are
alphabetically arranged.
Use arrow button to select which partition will
be worked.
Select Working
Partition - A
When the partition is set, the LCD will show the
following:
Set Partition to
A
4.9.6 Select Src Drive
This function selects CD-ROM or any CD writer as the source from which you can load data into
a particular partition as an image file.
Press ENT and arrow button to select
the source.
9-06. Image P: A
Image Src Drive
Then use arrow button to select the disc as the master
Select Img Src:
source.
01 IDE0 CD-ROM
After selecting the source, press ENT.
LCD will show the source information the following info:
Load image from
Drive ID-01
4.10 Edit Track
16
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Function 10, Edit Track, allows you to edit a collection of favorite songs from CDs. You’re able to
collect different tracks or songs on a number of CDs and merge them onto a single CD. This
process can be divided up into four parts: CD to CD, CD to HDD, Play Audio Track and Close
Session.
Press ENT and use the arrow button to select function 10.
10. Edit Track
4.10.1 CD to CD Edit
Select “CD to CD Edit” to select one or more tracks from CD-ROM and then copy onto blank CD-
R/RWs.
Press ENT to change setting.
10-01. Edit Track
CD to CD Edit
Follow the LCD to select the track that you want
to edit.
Select Track:
1/10
03:25
Press ENT to select the track. After the
track is selected, the “+” will appear beside 1/10 as shown.
Pressing ENT again will cancel the track.
Select Track:
+1/10
03:25
When the track selection is made, use arrow button
to move to the “End” manual.
Select Track:
End 1Trk03:25
Press ENT to finish the disc editing. Use arrow button
to make a selection.
End edit disc
and burn?Yes
LCD will show copying information as follows:
Copying- 24X Edit
1/10 - > 1/1
When copying ends, the LCD will show the
“Burn Complete!” message:
Burn Complete!
OK: 03
System will ask if you want to continue editing. Use the arrow
button to make a selection.
Continue edit
next Disc?Yes
If “Yes” is selected, the source disc will be
automatically ejected. Insert another disc.
Insert next disc
Follow the steps to select the track that you want
to edit. Then press ENT.
Select Track:
+2/10 04:25
When the track selection is made, use arrow button
to move to the “End” manual.
Select Track:
End 2Trk07:50
End edit disc
and burn?Yes
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Press ENT button to finish the disc edition.
Use the arrow button to make a selection.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying- 24X Edit
1/10 - > 2/2
LCD will show copying information as follows:
The 2/2 means the second track of all tracks you have
selected. So far you have selected two tracks from two
different CDs.
Burn Complete!
OK: 03
When copying is finished, the LCD will show the
following message:
The system will ask if you want to continue editing. Use arrow
button to select “no” then press
ENT.
Continue edit
next Disc?No
The system will ask to close the disc session.
Use arrow button to make “Yes” or “No”
selection.
Close all disc’s
session? Yes
LCD will show the following screen
when you are closing the session:
Closing Session
Please wait---
4.10.2 CD to HDD
This function lets you select one or more tracks from CD-ROM and then copy the source into a
certain HDD partition.
10-02. Edit Track
CD to HDD Edit
Press ENT to enter the setting.
Follow the LCD to select the track that you want
Select Track:
to edit. Here 1/10 means the number one of 10 tracks
1/10
03:25
and 3:25 means the playing time.
Press ENT button to select the track. After the
track is selected, the “+” will appear. Pressing
ENT again will cancel the track.
Select Track:
+1/10
03:25
Select Track:
End 1Trk03:25
When track selection is made, use arrow button to
move to the “End” manual.
Press ENT to finish the disc editing. Use arrow
button to make a selection.
End edit disc
and burn?Yes
The source will be loaded to hard drive. LCD
will show the loading information as follows:
Load- P0 -24X Edit
1/10 - > 1/1
When the “Image Load” is finished, the LCD will
show the message as follows:
Image load OK
The system will ask if you want to continue editing. Use the arrow
18
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Continue edit
next Disc?Yes
button to make “Yes” or “No” selection.
16
Insert next disc
If “Yes” is selected, the source disc will be automatically
ejected. Insert another disc.
Select Track:
+2/10 04:25
Follow the steps to select the track that you want
to edit. Then press ENT button.
Select Track:
End 2Trk07:50
When the track selection is made, use arrow button
to move to the “End” manual.
Press ENT button to finish disc editing. Use arrow button
to make a selection.
End edit disc
and burn?Yes
The track will be loaded as an image file onto hard drive.
LCD will the following information.
Load- P0 -24X Edit
1/10 - > 2/2
When loading is finished, the LCD will
show the message as follows:
Image load OK
System will ask you whether you want to continue editing.
Use arrow button to make a selection. Select
“No” to go next step.
Continue edit
next Disc?No
System will ask you if you want to burn from the HDD onto
CD-R/RW or move into a partition. Selecting “Burn” will
start the process.
Burn or Move to
Partition?Burn
LCD will show the copying information as follows:
Copy- P0 -24X 0%
1/2 Trk03:25
When burning is finished, the LCD will show
the message as follows:
Burn Complete !
OK: 03
Selecting “Move” will move the data from the hard
drive template to a certain partition.
Burn or Move to
partition? Move
Select the partition that the data will move into by
pressing the arrow.
Select Partition
A
LCD will show the moving information as follows:
Moving to P: A
0%
When moving is finished, the LCD will show
the message as follows:
Moving to P: A
OK!
If the chosen partition contains image data,
system will ask to overwrite it. Select “No” to
19
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Exists
keep the data image or “Yes” to overwrite it.
LCD will show the moving information as follows:
Moving to P: A
When moving is finished, the LCD will show the
message as follows:
Moving to P: A
OK!
4.10.3 Play Audio Track
This function allows your machine to be utilized as a music player. Plug in an AV terminal in the
audio port on the back of the device.
Press ESC and the arrow button to enter the play audio
10-03. Edit Track
function.
Play Audio Track
Use arrow button to select track you
are going to play.
Select Track:
1/10 03:25
Press ENT and LCD will display the playing information
as follows:
Playing Track-1
00:00 / 03:25
4.10.4 Close Session
Select “Close Session” will close the disc and restrict data writing. This function allows discs to be
read on any normal player.
Press ESC and arrow to select the function.
10-04. Edit Track
Close Session
Press ENT, the system will ask whether you want to
Close all disc’s
close. After this step, data cannot be written onto the disc.
session? Yes
Closing Session
LCD will show the message as follows:
Please wait---
When closing session is finished, the LCD will
show the following message:
Closing
Complete
4.11 Setup
This function allows you to change default settings. It is suggested that you use default setting for
optimal performance.
Press ENT button to enter the Setup function.
11. Setup
20
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
4.11.1 Language (optional)
Here are the available languages on the LCD: English, Traditional Chinese, Simplified Chinese
and Japanese.
11-01. Setup
Language
Press ENT to change the setting and ESC to
exit.
4.11.2 Burn Speed
This setting controls the burning speed of CD writers. Default setting is “Auto,”
which would use the highest available writing speed of the writer.
Press ENT to enter the setting.
11-02. Setup
Burn Speed
Use arrow button to change the burning
speed then press ENT.
Burn Speed
24X
4.11.3 Read Speed
This function lets you control the reading speeds of target CDs.
Press ENT to enter the setting.
11-03. Setup
Read Speed
Use arrow button to change the reading
speed then press ENT. The default is maximum but other
choices are 32X, 16X and 8X.
Read Speed
32X
4.11.4 Auto Start Drive
This function automatically tests or copies discs once you put the blanks discs into the writers.
Press ENT button to enter Auto Start Drive.
11-04. Setup
Auto Start
Use arrow button to change the number or
“Off” setting. Then press ENT or ESC to
go back 11-04 menu.
Auto Start
Drive
4.11.5 Start up menu
This setting lets you select any one of the functions, except Adv Setup, as the first item to appear
on the menu when you turn on your device.
11-05. Setup
Press ESC button to enter Startup Menu and
Startup Menu
ENT to enter the following figure:
Use the arrow button to select other function settings, which will
Startup Menu
1.Copy
be the first setting to appear when the device is turned on.
Then press ENT.
21
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
4.11.6 Auto Verify
This setting allows you to automatically verify if target CDs can be read after copying.
11-06. Setup
Auto Verify
Press ENT button to enter the following figure:
Use arrow button to change the “On” or “Off”
setting. Then press ENT or press ESC to go
return to 11-06 menu.
Auto Verify
Off
4.11.7 Auto Compare
This setting allows you to automatically compare the source CD and target CDs after copying.
Press ESC button and arrow to enter setting.
11-07. Setup
Auto Compare
Use arrow button to change “On” or “Off”
setting. Then press ENT to go
back 11-07 menu
Auto Compare
Off
4.11.8 Auto Prescan
This setting allows you to automatically scan if the source CD can be read correctly and also tests
the reading speed.
Press ENT button to enter Auto Prescan.
11-08. Setup
Auto Prescan
Use arrow button to change “On” or “Off” Setting.
Then press ENT or press ESC to return to 11-08 menu.
Auto Prescan
Off
4.11.9 Eject Disc
Eject disc allows three choices: Eject Good Only, Eject All Disc and Do Not Eject.
11-09. Setup
Eject Disc
Press ENT button to enter the following figure:
Use arrow button to select Eject Good Only.
Then press ENT or press ESC to return to 11-
09 menu.
Eject Disc
Eject Good
22
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Use arrow button to select Eject All Disc,
then press ENT or press ESC to return to 11-
09 menu.
Eject Disc
Eject All Disc
Use arrow button to select Do Not Eject. Then press
ENT or press ESC to go back 11-09 menu.
Eject Disc
Do Not Eject
4.11.10 Burn on the Fly
This setting lets you controls the burning methods. When the setting is “On”, the data will copy
directly from source drive to the target drives. When the setting is “Off”, the data will load into a
partition of the hard drive first. Then, the copying will be completed.
Press ENT button to enter Burn On The Fly.
11-10. Setup
Burn On The Fly
Use arrow button to change the On or Off
Setting. Then press ENT or press ESC to return to
Burn On The Fly
On
The 11-10 menu.
If the system does not connect with hard drive,
the LCD will show the following message.
There is no HDD !
4.11.11 Burn Mode
This setting lets you control the burning methods. There are two modes: Disc At Once (DAO) or
Track At Once (TAO). Default setting is DAO. Some CD writers may support different writing
methods. If the method selected is not supported, duplicator will automatically switch to the other
one.
.
Press ENT button to enter Burn Mode.
11-11. Setup
Burn Mode
Use arrow button to change TAO or DAO
mode setting. Then press ENT or press ESC
to return to 11-11 menu.
Burn Mode
DAO
4.11.12 Button Sound
This setting allows you to control the sound when you press it.
11-12. Setup
Button Sound
Press ENT button to enter Button Sound.
Use arrow button to change On or Off
setting. Then press ENT or press ESC to return to
11-12 menu.
Button Sound
On
23
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
4.11.13 Device Info
This function shows the information of the CD-ROM and any CD writer you have installed.
11-13. Setup
Device Info
Press ENT button to enter the device information.
00 IDE0 Master
Use arrow button to select the device or press
ESC to go back 11-13 menu.
CD-ROMꢀꢁꢀTEAC
Press ENT button to see the device information
and ESC to return to the 11-13 menu.
CD-540E
3.0A
Use arrow button to select another device or
press ESC to return to the 11-13 menu.
01 IDE1 Master
ꢀꢁꢀ
Press ENT button to see the device information
and ESC to return to the 11-13 menu.
CD-R PX-W2410A
1.01
Use arrow button to select another device or
press ESC to return to the 11-13 menu.
02 IDE2 Master
ꢀꢁꢀ
Press ENT button to see the device information
and ESC to return to the 11-13 menu.
CD-R PX-W2410A
1.01
Use arrow button to select another device or
press ESC to return to the 11-13 menu.
03 IDE2 Master
CD-RW :ꢀPLEXTOR
Press ENT to see the information and ESC
to return to the 11-13 menu.
CD-R PX-W2410A
1.01
4.11.14 System Info
This function shows the information of the system.
Press ENT button to enter the System Info and see
the next information. Press ESC to exit.
11-14. Setup
System Info
The LCD shows
Coolcopy3 as follows:
CD Duplicator
1-3 ver: 1.10B
SST: 39SF020
2001 / 11 / 16
The LCD shows
Coolcopy7 as follows:
CD Duplicator
1-7 ver: 1.10T
WINBOND: W49F002U
2001 / 11 / 16
24
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
11-15. Setup
Quick Erase
4.11.15 Quick Erase
This function will quickly erase the data on the disc.
Press ENT button to enter the Quick Erase
and ESC to exit.
Use arrow button to confirm whether you want to erase
the data. Select the “Yes” or “No” setting. Then press
ENT or press ESC to return to 11-15 menu.
All data will be
lost, erase? Yes
LCD will show the information as follows:
Erasing disc
00:24 (Quick)
When erasing disc function is finished, the LCD will
display as follows:
Quick Erase
OK:01 Fail:00
4.11.16 Full Erase
This function is to completely erase the data on the CD rewriteable discs.
Press ENT to enter the Full Erase.
11-16. Setup
Full Erase
Use arrow button to select “Yes” or “No.”
All data will be
Then press ENT or ESC to return to 11-16 menu.
lost, erase? Yes
LCD will show the information as follows:
Erasing disc
When finished, the LCD will show the message the
following message:
Full Erase
OK:01 Fail:00
4.12 Adv Setup
This function allows you to change the system configuration. Changes should be made only when
you are fully familiar with the function. To enter the function, please press “ESC” button for 2
seconds.
4.12.1 UnderRun Protect
This function lets you control Buffer Under Run Protection settings, such as Burn Proof,
SafeBurn, JustLink, Seamless Link, etc.
12-01. Adv Setup
Press ENT button to enter “UnderRun Protect.
UnderRun Protect
25
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Use arrow button to change the
setting. Then press ENT or ESC to return to the
12-01 menu.
UnderRun Protect
On
4.12.2 Overburn
This setting lets you decide whether to copy beyond the limit of the CD or not.
12-02. Adv Setup
Overburn
Press ENT button to enter Overburn.
Use arrow button to change the
setting. Then press ENT or ESC to return to the
12-02 menu.
Overburn
On
4.12.3 Read Error Skip
This function allows you to neglect any error that occurs during copying. You can use this function
to copy some defective CDs.
12-03. Adv Setup
Read Error Skip
Press ENT button to enter Read Error Skip.
Use arrow button to change the
setting. Then press ENT or ESC to go
back to the 12-03 menu.
Read Error Skip
Off
4.12.4 Format Hard Disk
This function allows you to partition the hard drive.
Press ENT button to enter Format HDD.
12-04. Adv Setup
Format HDD
Use arrow button to change the
setting. Then press ENT or ESC to go
back to the 12-04 menu.
All data will be
lost, format? Yes
If the system does not connect with hard drive,
the LCD will show the message as follows:
There is no HDD!
4.12.5 Verify HDD
This function is to verify if the hard disc or any of its partitions are working well.
Press ENT to enter Verify HDD.
12-05. Adv Setup
Verify HDD
26
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Use arrow button to change setting to Disk.
Then press ENT or ESC to go back to the 12-
05 menu.
Verify Disk or
Partition? Disk
Use arrow button to change setting to Parti.
Then, press ENT or ESC to go back to the 12-05 menu.
Verify Disk or
Partition? Parti
4.12.6 Burn-in
This function is a burn-in test, which will simulate the copying process multiple times. After each
cycle, the CDs on the CD writers will be ejected automatically and re-inserted again for
continuous testing.
Press “ENT” button to enter “Burn-in” and
12-06. Adv Setup
Burn-in
“ESC” to exit
The data will not be written on the blank
CD discs and the discs will remain blank
after the test.
Burn-in
Test
.
Using arrow button to change
“RunContinuous”, “1~10”, “10~100”,
“100~1000” setting. Press “ENT” or “ESC”
button to go back 12-06 menu.
Sel burn-in num:
Run Continuous
The system will repeat to erase and write
on the CD-RW discs. Only CD+RW discs can
be rewritten.
Burn-in
Erase&Copy
Using arrow button to change
Sel burn-in num:
Run Continuous
“RunContinuous”, “1~10”, “10~100”,
“100~1000” setting. Press “ENT” or “ESC”
button to go back 12-06 menu.
4.12.7 Update Firmware
This function will update your firmware to the latest version. Insert the CD disc which contains the
latest firmware data (firmware CD disc) into the CD-ROM drive and the duplicator will find the
data and update its firmware automatically. During updating, do not turn off the power of machine
because the update will not be finished until machine resets itself.
The Update Firmware function updates firmware to the latest version.
2. Unzip the firmware you have and write the file “cdxxx.bin” into the root directory of a blank
CD-R or CD-RW disc. You have to close the session of the CD. If the same CD disc still has
capacity to add more data, it can be used to store newer versions of firmware. When updating the
firmware program from the CD, only the one from last session will be used. Versions from
previous sessions will be ignored.
Select source drive to CD-ROM first! Then
12-07. Adv Setup
Update Firmware
press “ENT” button to enter “UpdateFirmware”
and “ESC” to exit.
27
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
System will search the new firmware from the
CD and the LCD will show the process as left.
When find the new firmware, just press “ENT”
button. The system will update it.
Searching F/W---
XXX/XXXXX
4.12.8 Compare Firmware
This function will help you compare your current control firmware version and the updated version
in your firmware disc that you insert into the CD-ROM.
Press “ENT” button to enter “Compare Firmware”
12-08. Adv Setup
and “ESC” to exit.
.
Compare Firmware
4.12.9 H/W Diagnostic
This function will detect which types of devices are connected with the control. The LCD will show
the hardware information.
Press the ENT button to enter “H/W Diagnostic”
and “ESC” to exit.
12-09. Adv Setup
H/W Diagnostic
LCD will ask user to do the button test. Following
the LCD instruction test each function button.
ꢀꢀꢀꢀꢀEnter ESC
Hold ESC to exit
After the button function testing, the system will self-test SDRAM, the hardware connecting test,
and flash test. Every testing process will be shown on the LCD. It just takes a few minutes to get
the results of hardware diagnostics. It is an easy way to know if the system works properly.
When testing is finished, the LCD will show the
“Test finished” message. Press “ESC” button to
go back 12-09 menu.
Test finished
4.12.10 Load Default
This function will reset whole previous setting back to factory’s default setting. Different settings
will cause duplicator to react differently.
12-10. Adv Setup
Press “ENT” button to enter “Load Default” and
Load Default
“ESC” to exit.
Use the arrow button to change settings. When
Load Default
Config? Yes
“Yes” is selected, the duplicator will return to
factory’s default setting.
Load Default
OK
The LCD message will show that the setting has
been changed by with the follow message:
28
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Trouble Shooting
1. No display on LCD or the unit does not operate when power on.
•
Please check the connection of power cable and that the power
outlet is normal.
•
Turn off the power of machine, open the case of duplicator, and check if
there are any problems with the power cable.
2. LCD shows the Error message.
•
During operation like Copy, Test, Compare and Verify, you may press ESC
button to abort the operation. An Error message will be shown no the LCD.
Some CD writers will cause the duplicator to reset and you have
to re-start the power to get the duplicator to function properly.
•
•
•
A failed reading may cause an error message to show on the LCD display.
Change the master CD and try again.
During operation, if a read error, buffer under run or writing error occurs, the
LCD will show error message like: Pass xx, failed xx.
If there is no device connected and detected by duplicator during power-on,
the duplicator will show an error message on the LCD before entering the main menu.
3. CD-ROM can not read disc and shows error message.
•
•
Check the format of master CD or master CD itself for damage.
Use any of the CD-Writers to read the master. If it works, the CD-ROM may be
defective or not compatible with CD-ROM.
4. Buttons do not function.
•
•
•
May be still busy on task.
Button malfunction.
Faulty board.
5. Copy completed but CD-R disc is not readable / executable?
•
•
Use the compare function to check.
Change another CD-ROM drive to test.
6. The failure rate is high.
•
•
•
•
Lower the speed of the CD-Writers and try again.
Quality of blank disc is poor.
Check for latest firmware version.
Check the CD-Writer maximum writing speed. If you want to copy at 24X writing
process or higher, please copy to hard drive first and then to CD.
7. Can not boot-up or failure to upgrade firmware.
•
Contact your dealer to solve the problem. Please note that ay be charged
for this.
•
Check to see if the BIOS program is correct since customers often download
the wrong program or simply write the zipped file to CD when it should be first
unzipped before writing.
•
A failed upgrade might cause a failed boot. This can only be solver by returning
the control board to agent or factory directly. It is not necessary to return
whole system under failed upgrade.
29
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Can not find the “12. Adv Setup” function.
Press “ESC” button for 2 seconds to enter the “Adv Setup”.
•
9. To cancel the duplicator working process.
•
Press “ESC” button for 2 seconds to cancel any “Copy”, “Test”, or “Verify” etc.
function while the job is in progress.
30
Copyright ©2005 by ILY Enterprise Inc.
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|