IDEAL INDUSTRIES, INC.
TECHNICAL MANUAL
MODEL: 61-310
This Service Manual provides the following information:
●
●
●
●
●
Precautions and safety information
Specifications
Basic maintenance (cleaning, replacing the battery and fuses)
Performance test procedures
Calibration and calibration adjustment procedures
Form Number: TM61310
Revision: 2. Date: August 2007
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 1
Introduction
Warning
To avoid shock or injury, do not perform the verification tests or calibration procedures
described in the manual unless you are qualified to do so.
The information provided in this document is for the use of qualified personnel only.
Caution
The 61-310 series contain parts that can be damaged by static discharge.
Follow the standard practices for handling static sensitive devices.
For additional information about IDEAL INDUSTRIES, INC. and its products, and services,
visit IDEAL INDUSTRIES, INC. web site at:
Precautions and Safety Information
Use the meter only as described in the Service Manual. If you do not do so, the protection
provided by the meter may be impaired. Read the “Safety Information” page before servicing
this product.
In this manual, a Warning identifies conditions and actions that pose hazard (s) to the user; a
Caution identifies conditions and actions that may damage the meter or the test instrument.
The Symbols
The symbols used on the meter and in this manual are explained in Table A.
Table A. The Symbols
Risk of electric shock
Refer to the manual. Important information.
DC measurement
Equipment protected by double or reinforced
insulation
Battery
Earth
AC measurement
Conforms to EU directives
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 2
SAFETY
Review the following safety precautions to avoid injury and prevent damage to this product or
any products connected to it. To avoid potential hazards, use the product only as specified.
For operating instructions, see the 61-310 Digital Multimeter Instruction Manual.
CAUTION: These statements identify conditions or practices that could result in damage to
the equipment or other property.
WARNING: These statements identify conditions or practices that could result in personal
injury or loss of life.
Specific precautions
Use proper Fuse. To avoid fire hazard, use only the fuse type and rating specified for this
product.
Do not operate without covers. To avoid personal injury, do not apply any voltage or current
to the product without covers in place.
Electric overload. Never apply a voltage to a connector on the product that is outside the
range specified for that connector.
Avoid electric shock. To avoid injury or loss of life, do not connect or disconnect probes or test
leads while they are connected to a voltage source.
Do not operate in wet/damp conditions. To avoid electric shock, do not operate this product
in wet or damp conditions.
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 3
SPECIFICATIONS
All specifications are warranted unless noted typical and apply to the 61-310.
Stated accuracies are at 23°C±5°C at less than 70% relative humidity and without the battery
indicator displayed.
General specifications
Characteristics
Description
Display count
3 ½ digit liquid crystal display, 1999 count
3 times / sec
Numeric update rate
Polarity display
Automatic, positive implied
“OL“ is displayed
Over range display
Low Battery indicator
Automatic power-off time
is indicated
Automatic backlight off = 30 minutes
Power source
9Vbattery, NEDA 1604, JIS006P, IEC6F22
Maximum input voltage
600V CAT II between V and COM
Maximum floating voltage
Maximum mA input current, V/ma and COM
Maximum A input current, 10A and COM
V connector
600V CATII between any termianl and earth ground
Fused 250mA at 250Vrms
10A , not Fused, max time is no longer that 15 seconds
V
, V , Ω,
,
, mA, Temperature
Temperature Coefficient
Battery Life
0.1×(Spec. Accuracy) per °C, <18°C or >28°C
Alkaline 9V, approximately 200 hours
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 4
Measurement Characteristics
Accuracy is ±(% reading + number of digits) at 23°C ± 5°C, less than 80% R.H.
(1) DC Volts
Over voltage
protection
Range
Resolution
Accuracy
200.0mV
2.000V
100μV
1mV
0.5% + 2
0.8% + 2
600V rms
20.00V
10mV
100mV
1V
200.0V
600V
Input Impedance: 10MΩ
(2) AC Volts
Range
Over voltage
protection
Resolution
Accuracy
40-400Hz
1.2% + 10
1.2% + 10
200.0V
600V
100mV
1V
600V rms
Input Impedance: 4.5MΩ
AC Conversion Type: Average sensing rms indication calibrated to the sine wave input.
(3) DC Current
Range
Resolution
0.1mA
Accuracy
1.5% + 2
3.0% + 5
Overload protection
250mA/250V Fast Blow Fuse
Not fused, 15 sec Max
200.0 mA
10.00A*
.01A
*
Caution: Do not make high current measurements on the 10A scale for longer that 15
seconds. This should be followed by a 15 minute cool down period. Exceeding 15 seconds
may cause damage to the meter and/or the test leads.
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 5
(4) Resistance
Range
Over voltage
protection
Resolution
Accuracy
200.0Ω *1
2.000KΩ
20.00KΩ
200.0KΩ
2.000MΩ
20.00MΩ *2
0.1Ω
1Ω
0.8% + 4
10Ω
0.8% + 2
3.0% + 3
250V rms
100Ω
1KΩ
10KΩ
Open circuit Voltage: -1.5V approx.
*1 < 5 digit of reading rolling.
*2 ± 2% of reading rolling.
(5) Diode Check and Continuity
Max. Test
Current
Max. Open
Range
Resolution
Accuracy
Not specified *
Circuit Voltage
1mV
1mA, approx.
2.8V, approx.
Overload Protection: Not specified
Continuity: Built-in buzzer sounds when resistance is less than approximately <30 Ω with a
response time of approximately 100 msec.
(6) Temperature: Type K thermocouple
Overload
Range
Resolution
Accuracy
protection
-20 to 16 ºC
17 to 400 ºC
401 to 750 ºC
-4 to59 ºF
1º
1º
1º
1º
1º
1º
2.5% + 10
1.0% + 5
2.5% + 10
2.5% +19
1.0% +9
Not Specified
60 to 750ºF
751 to 1382ºF
2.5% +19
(7) Auto Power Off (APO)
If the meter idles for more than 15 minutes, the meter automatically turns the power off.
(8) Data Hold
Press the HOLD button to freeze the reading in the display, “H” will appear on LCD display.
Press the HOLD button again to release the data hold function.
(9) Battery Test 1.5 and 9V
Test current 1.5V is approximately 120mA
9.0V is approximately 9mA
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 6
Physical and Environmental Characteristics
Characteristics
Description
150mm(H) ×76mm (W) ×38mm(D) (with holster)
5.9” (H) x 3.0”(W) x1.5”(D)
Dimensions (H×W×D)
Weight (with battery& holster)
Environmental characteristics
Temperature operating range
Non-Operating
0.219Kg (7.1 oz.)
Description
0 to +40°C
-20 to +60°C <80% R.H.
<75% R.H.
Humidity (operating)
Altitude
6561.7 Ft. (2000m)
Indoor Use
Indoor Use
Certifications and compliances
Safety
Complies with UL 61010B-1
V / Ω/Temp/mA, UL 61010B-1, UL 61010-B-2-031, EU
Input Safety Rating
61010-1 EN61010-2-031, Cat II 600Volts
CAT III: Distribution level mains, fixed installation.
CAT II: Local level mains, appliances, portable equipment
CAT I: Signal level, special equipment or parts of equipment,
telecommunication, electronics.
Do not operate in environments where conductive
Pollutants may be present.
Pollution Degree 2
Meets the intent of Directive 89/336/EEC for Electromagnetic
Compatibility and Low Voltage Directive 73/23/EEC for product
safety. Compliance was demonstrated to the following specifications
as listed in the official Journal of the European Communities:
En 55011 Class A: Radiated and Conducted Emissions.
En 50082-1 Immunity:
EC Declaration
of Conformity
IEC 801-2 Electrostatic Discharge
IEC 801-3 RF Radiated
En 61010-1 Safety requirements for electrical equipment for
measurement, control, and laboratory use.
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 7
Required Equipment
Required equipment is listed in Table B. If the recommended models are not available,
equipment with equivalent specifications may be used.
Repairs or servicing should be performed only by qualified personnel.
Table B. Required Equipment
Equipment
Required Characteristics
Recommended Model
AC Voltage Range: 0 ~ 750V AC
Accuracy: ±0.07% (Basic)
Calibrator
Fluke 5500 or Wavetek
9100 Calibrator or
equipment
Frequency Range: 40 ~ 1KHz
Accuracy: ±2%
DC Voltage Range: 0 ~ 1000V DC
Accuracy: ±0.006% (Basic)
Current Range: 0 ~ 10A
Accuracy: AC (40Hz to 1KHz): ±0.08% (Basic)
DC: ±0.02% (Basic)
Frequency Source: 5.00Hz ~ 100MHz
Accuracy: ±0.001%
Amplitude: 0.5V p-p ~ 1.0V p-p (square wave)
Accuracy: ±5%
Resistance Range: 1Ω ~ 100MΩ
Accuracy: ±0.03% (Basic)
Capacitance Range: 1pF ~ 10mF
Accuracy: ±0.10% (Basic)
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 8
Basic Maintenance
Warning
To avoid shock, remove the test leads and any input signals before opening the case or
replacing the battery or fuses.
Opening the Meter Case
Caution
To avoid an unintentional short circuit, always place the uncovered meter assembly on a
protective surface. When the case of the meter is open, circuit connections are exposed.
1. Disconnect test leads from any live source, turn the rotary switch to OFF, and remove
the test leads from front terminals.
2. For battery replacement follow instructions under Replacing the Battery section
3. For Fuse replacement follow instructions in the Fuse Replacement section.
Replacing the Battery
The 61-310 meter is powered by a 9V battery, types are, NEDA 1604, JIS006P, IEC 6F22
1. Remove the rubber holster.
2. Remove the two screws on the battery cover and open the battery cover.
3. Unsnap the old battery and snap in the new battery.
4. Return the battery cover and reinstall the two battery cover screws.
5. Replace the rubber boot.
Battery and Fuse Replacement
FIGURE 1
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 9
Replacing Fuses
Warning
To avoid electrical shock, remove the test leads and any input signals before replacing the
battery or fuses.
To prevent damage or injury, INSTALL ONLY quick acting fuses with the following Amp/Volt
current interrupt rating:
F-310 Fuse: 250mA 250V FAST BLOW Fuse
Fuse Replacement
The 61-310 replacement fuse is part number: F-310
Fuse Rating is: 250mA 250V FAST BLOW
1. Remove the rubber holster.
2. Remove the two screws on the battery cover and open the battery cover.
3. Remove the two screws under the battery cover.
4. Lift up on the back case until the case unsnaps from the front case near display.
•
Replace the defective fuse with the standard rated fuse for this meter.
5. Return the back case cover, reinsert the case screws.
It is recommended to replace the old battery with a new battery.
•
6. Return the battery cover and reinstall the two battery cover screws.
7. Replace the rubber boot.
Caution Use only a fuse with the amperage, interrupt voltage, and speed rating
specified.
Cleaning
Warning
To avoid electrical shock or damage to the meter, never allow water inside the case. To avoid
damaging the meter’s housing, never apply solvents to the meter.
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 10
Performance Tests
The following performance tests verify the complete operability of the meter and check the
accuracy of each meter function against the meter’s specifications.
Accuracy specifications are valid for a period of one year after calibration, when measured at
an operating temperature of 18°C to 28°C and a maximum of 80% relative humidity.
To perform the following tests, it is not necessary to open the case, no adjustments are
necessary, merely make the required connections, apply the designated inputs, determine if
the reading on the meter display falls within the acceptable range indicated.
If the meter fails any of these tests, it needs calibration adjustment or repair.
Testing the Voltage Function
To verify accuracy in the AC and DC voltage ranges, do the following:
1.
2.
3.
4.
5.
Turn the rotary switch to “DCV” function and range shown in Table1.
Connect the calibrator to the VΩ and COM inputs on the meter.
Set the calibrator for the voltage from steps 1 to 7 in Table 1.
Compare the reading on the meter display with the display reading shown in Table 1.
If the display reading falls outside of the range shown in Table 1, the meter does not
meet specification.
Table 1: DC Voltage Test:
Range
Step
Input
190.0mV
2.0mV
Reading
188.8 to 191.2
1.8 to 2.2
1
2
3
4
5
6
7
200mV
200mV
2V
1.900V
-1.900V
19.00V
190.0V
600V
1.888 to 1.912
-1.888 to -1.912
18.88 to 19.12
188.8 to 191.2
593 to 607
2V
20V
200V
600V
6.
7.
8.
9.
Turn the rotary switch to the “ACV “ function and range shown in Table 2.
Set the calibrator for the voltage and frequency from step 1 to 6 in Table 2.
Compare the reading on the meter display with the display reading shown in Table 2.
If the display reading falls outside of the range shown in Table 2, the meter does not
meet specification.
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 11
Table 2: AC Voltage Test:
Range
200V
200V
200V
200V
600V
600V
Step
Input
2.0V
Frequency
60Hz
Reading
1
2
3
4
5
6
1.0 to 3.0
2.0V
400Hz
60Hz
1.0 to 3.0
190.0V
190.0V
600V
600V
186.7 to 193.3
186.7 to 193.3
583.0 to 617.0
583.0 to 617.0
400Hz
60Hz
400Hz
Testing the DC milliamps and DC amps Function
1. Turn the rotary switch to the DCA function and range shown in Table 3.
2. Apply the inputs for steps 1-3 in Table 3.
3. For each input, compare the reading on the meter display to the reading for your meter
in Table 3.
4. If the display reading falls outside of the range shown in Table 3, the meter does not meet
specification.
Table 3: DC Current Test:
Range
200 mA
200 mA
10 A
Step
Source
2.00 mA
190.0 mA
10.00 A
Reading
1.8 to 2.2
1
2
3
186.9 to 193.1
9.65 to 10.35
Testing the Resistance Function
To verify the accuracy of the resistance function, do the following:
1. Connect the calibrator to VΩ and COM on the meter.
2. Turn the rotary switch to OHM. function and range shown in Table 4
3. Apply the inputs for steps 1-6 in Table 4.
4. Compare the meter display readings to the display readings in Table 4.
5. If the display reading falls outside of the range shown in Table 4, the meter does not meet
specification.
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 12
Table 4: Ω Resistance Test:
Range
Step
Source
2.0Ω
Reading
*200 OHM
*200 OHM
2K OHM
1
2
3
4
5
7
1.6 to 2.4
190.0Ω
1.900KΩ
19.00KΩ
190.0KΩ
19.00MΩ
188.3 to 191.7
1.883 to 1.917
18.83 to 19.17
188.3 to 191.7
18.40 to 19.60
20K OHM
200K OHM
20M OHM
*Lead resistance on the 200 ohm range is not included in error.
Checking the Diode Test Function
To check the diode test function, do the following:
1. Connect the calibrator to the VΩ and COM inputs on the meter.
2. Turn the rotary switch to
.
3. Apply 1.500V DC. The meter display should read approx. 1.500V dc.
4. Apply a 20-ohm resistor to the meter, the built-in buzzer buzzes.
Testing the Temperature Function
Before beginning this test allow 30 minutes for the meter and calibrator temperature adapter to
reach ambient temperature.
To verify the accuracy of the Temperature function, perform the Following:
1. Apply the temperatures in steps 1 - 7 to the VΩTemp and COM inputs using a
temperature adapter to the meter.
2. Turn the rotary switch to ºC or ºF (Range is –20 to 750 ºC or –4 to 1382 ºF)
3. Compare the reading on the meter display to the reading in Table 4.
Note : Meter selects the proper range automatically. Each measurement takes a few seconds.
4. If the display reading falls outside of the range shown in steps 1–7 of Table 4, the meter
does not meet specification.
Table 5: Temperature Test:
Range
ºC
Step
Source
-20 ºC
0 ºC
Reading
-30 to -10
-10 to 10
1
2
3
4
5
6
7
ºC
ºC
400 ºC
750 ºC
-4 ºF
391 to 409
721 to 779
-23 to 15
ºC
ºF
ºF
32 ºF
13 to 51
ºF
1382 ºF
1328 to 1436
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 13
Calibration Procedure
To Recalibrate your meter: It is recommended that the Multimeter be calibrated once each year.
1. Perform calibration at an ambient temperature of 23°C±2°C and a relative humidity of
<70% Disconnect the test leads and turn the meter off. Remove the test leads from the
front terminals.
2. Position the meter face down. Remove the battery cover screws and the 2 bottom
case cover screws.
3. Lift the end of the bottom case cover until it gently unsnaps from the case top at the
end nearest the LCD.
(A) DCV and ACV Calibration (Adjust VR1)
1. Set the rotary switch to the "200mV DC" position.
2. Set the output of the DC calibrator for 190.0mV ±0.02% and connect to V/Ω/Temp and
COM input terminals on meter.
3. Using a small flat-tipped screwdriver to adjust VR1 until the display reads 198.9 to 190.1
mV.
4. Disconnect the DC calibrator from the meter.
(B) DC A Calibration (Adjust VR5)
1. Set the rotary switch to the "10 A DC" position.
2. Set the output of the calibrator to 5A DC
3. Connect the calibrator current output to the 10A and COM input terminals on
meter.
4. Using a small flat-tipped screwdriver to adjust VR4 until the display reads 4.95 to
5.05 amps
(C) ºC Calibration (Adjust VR2)
1. Set the rotary switch to the "ºC " position.
2. Set the output of the calibrator to 0 ºC
3. Connect the calibrator Temperature output to the V/Ω/Temp and COM input terminals
4. Using a small flat-tipped screwdriver, adjust VR2 for a 0ºC ±1ºC (-1 to 1) display
(D) ºF Calibration (Adjust VR3)
1. Set the rotary switch to the "ºF " position.
2. Set the output of the calibrator to 32 ºF
3. Connect the calibrator Temperature output to the V/Temp and Com input
4. Using a small flat-tipped screwdriver adjust VR3 for a 32ºF ±1ºF (31 to 33) display
Form Number TM61310
Rev 2 Aug 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
|