Download from Www.Somanuals.com. All Manuals Search And Download.
U.S.A.
U.S.FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE
STATEMENT INFORMATION TO THE USER
NOTE : This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet of a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/Monitor technician for assistance.
Changes or modification not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Connecting of peripherals requires the use of grounded shielded signal cables.
Download from Www.Somanuals.com. All Manuals Search And Download.
DECLARATION OF CONFORMITY
For the following product :
All of Digital sigange HYUNDAI IT provides
Manufactured at :
(factory name, address)
1. Hyundai IT Corp. 1229 In-ri, Apo-eup Gimcheon, Gyeongsangbuk-do 740-860 Rep. of Korea
2. Hyundai IT Corp. San 136-1 Ami-ri, Bubal-eub, Ichon-si, Kyungki-Do, 467-860 Rep. of Korea
We herewith confirmed to comply with the requirements set put in the Council Directive on the
Approximation of the Lows of the Member States relating to Electromagnetic Compatibility Directive
(89/336/EEC), Low-Voltage Directive(73/23/EEC , 93/68/EEC) . For the evaluation regarding the Directives,
the following standards were applied:
EN60065 : 2002
EN55022 : 1998+A1 : 2000 +A2 : 2003 CLASS A
EN55024 : 1998+A1 : 2001 +A2 : 2003
EN 61000-3-2 : 2000 +A2 : 2005
EN 61000-3-3 : 1995 +A1 : 2001 +A2 : 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
Contents
Major features...............................................................................................2
Safety Information........................................................................................2
Be sure to understand ..................................................................................5
Check the product list...................................................................................6
Proper location for product installation......................................................7
Title and function of each part ....................................................................8
How to Connecting Kiosk...........................................................................11
How to Connecting Digital RGB(HDMI).....................................................12
How to Connecting analog RGB (PC D-SUB).............................................14
How to Connecting the component (Option)...........................................16
How to Connecting the the video (Option)..............................................18
Adjusting OSD and explanation of its function .......................................19
Diagnosis .....................................................................................................33
Specifications ..............................................................................................35
**REMOTE CONTROL / RS232C COMMAND SPEC
Download from Www.Somanuals.com. All Manuals Search And Download.
1/35
DIGITAL SIGNAGE
This product has been designed to enable the user ease of use, and display information
effectively and conveniently.
Major features
• TFT LCD Module adopted
D320ML(I/G) / D400ML / D420ML(I/G/P/T) / D460ML(I/G/P/T/H) / D468ML(I/G/P/T/H) /
D460SL(I) : 1366 x 768 WXGA (HD)
D405ML(I/G) / D407ML(I/G/P/T) / D425ML(I/G/P/T)/ D465ML(I/G) / D467ML(I/G/P/T) /
D525ML(I/G) / D825ML(I/G) / D525SL(I) / D705ML(I/G) / D705SL(I) / D825SL(I)
: 1920 x 1080 WUXGA (Full HD)
• Vivid digital color display
• OSD control function
• Automatic Image control
• Automatic temperature control
• Analog/Digital RGB(HDMI) input and output
• Y Pb Pr/AV input and output
• Built in multi-vision function
This product is designed to ensure user's safety.
Avoid the following items to prevent serious electric shot and other dangers.
Safety Information
- Do not place wet objects on or around the product or the power cord.
- Do not cover or insert anything over or into the ventilation openings.
- Do not place in a location where damage can be caused by oil, smoke, high temperature,
high humidity, dust etc.
- The product is not suitable for use at visual display workplaces according to §2 of the German
Ordinance for Work with Visual Display Units.
ꢀ/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
- The main plug of the power supply cord shall remain readily operable.
- An apparatus with CLASS I construction shall be connected to a Mains socket outlet
with a protective earthing connection.
- Make sure that the power cord and other cables are correctly plugged in.
- Plug the power cord correctly into the end, do not wobble/jiggle, it may cause electric shock fire.
- Do not touch the power cord with wet hands, it may cause electric shock.
- Overloaded AC outlets and extension cables are as dangerous as the power cord being damaged,
call service engineer for replacement as it may cause electric shock or fire.
- Do not use multiple devices in a single power outlet, it may cause overheating or fire.
- Do not use or place sharp objects near the LCD surface, as this can cause damage to the screen itself.
- When cleaning the LCD screen / Surface, do not use chemical cleaning products as this can
seriously damage the special coatings on the screen. Only use water to dampen a soft cloth and
lightly clear the screen.
- Over time dust deposits can build up inside the product, this can cause the product to overheat
thus causing premature malfunction or fire. Please do not attempt to clean the inside of the
product yourself, please contact the local service agent.
- Do not use alcohol or strong chemical solvent such as methyl, ethyl or a Isopropyl.
- In the case of cleaning, be sure to remove the power cord and wipe with a soft dry fabric.
- Keep batteries for the remote control out of children's sight.
- Batteries should be inserted using the correct polarity (+,-).
- Use only new batteries, do not mix old & new.
- Place unit on a stable bracket or surface.
- More than 2 people should work together when moving or installing.
Download from Www.Somanuals.com. All Manuals Search And Download.
3/36
DIGITAL SIGNAGE
- Do not hang on or jump to the product or mounting rack.
- When the product is left unused for a long time, be sure to unplug the power cord.
- In the case of damage or breakage do not attempt to self repair, please contact local service
engineer.
- For D460SL(I), D525SL(I), D705ML(I/G), D705SL(I), D825SL(I), install the product on the flat
surface and secure the wheels not to move itself or fall down.
- For D460SL(I), D525SL(I), D705ML(I/G), D705SL(I), D825SL(I), make sure to turn the power off
before connecting cables.
- This manual contains general instructions for the display products only so refer to the
provided CD-ROM manual and the driver installation manual for the driver installation
instructions for touch screen and/or touch screen itself.
- The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.
- Shall be connected to a MAINS socket outlet with a protective earthing connection.
- The disconnect device shall remain readily operable.
- The socket-outlet shall be installed near the equipment and shall be easily accessible.
- Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
ꢁ/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
Be sure to understand
Image quality of the product
CAUSE
Due to the nature of LCD's property, Afterimage can occur. Afterimage appears when
identical frames / images are displayed continuasly. If displayed for prolonged periods of
time this can become permanent.
PREVENTION
When you display a freeze frame for a long time, lower the brightness and contrast
(Brightness, 70/ Contrast, 80). Also it can be prevented by using moving frame.
COUNTERMEASURES
Temporary afterimage can be alleviated by displaying white or moving frame about 10
hours.(But, permanent afterimage cannot be disappeared according to the property of
LCD) This method is used to remove temporary afterimage that may occur after
displaying a still frame for a certain time.
It can take several minutes or hours to remove afterimage according to the severity. In
the case that your cannot avoid displaying identical still image continuously, you can
prevent it by displaying moving image for 2 or 3 minutes in every hour. As the brightness
of still image and time of display are the cause of afterimage, you are recommended to
lower the brightness in that case.
Above problem shall not be covered by warranty.
!
Download from Www.Somanuals.com. All Manuals Search And Download.
5/36
DIGITAL SIGNAGE
Please check the following components provided with the product after you open the box.
Check the product list
Remote control & batteries
Power Cord
D-SUB Cable
Base Frame Type
User's manual
HDMI to DVI Cable (Option)
RS232C Cable (Option)
HDMI cable
Kiosk Type (Landscape)
Kiosk Type (Portrait)
please check the following components provided with the product after you open
the box and contact the dealer if any missing.
!
** The contents may vary depending on models and sometimes the contents may be attached on the product.
6/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
1. Locate the product at least 30cm away from the electric appliance or heating product.
2. The product must be placed at least 10cm away from the wall and ground.
3. Keep the product out of direct ray of light and locate screen not to be reflected by the
sunlight.
Proper location for
product installation
4. Make sure the mounting rack firmly tightened before installation.
Please take extra care during installation, it is possible to cause damage if the unit is
handled badly or knocked.
!
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂ/36
DIGITAL SIGNAGE
Remote control receiving sensor.
Menu button : to display menu or exit from the menu.
select button.
Title and function of each
part
1
2
3
3
4
5
Power display LED red-stand by/ Green-working.
OSD button.
6
7
8
9
0
~
To move down in OSD menu.
0
Power button ; to turn the power on or off.
To move up in OSD menu.
Control Panel
Input selection button : to select other connected
device.
To move left and control the volume down in OSD menu.
To move right and control the volume up OSD menu.
3
4
5
6
7
8
9
0
POWER
SOURCE
MENU
SELECT
VOL
1
2
Kiosk Type (Rear)
Base Frame Type (Front)
** The locations of OSD board and remote control receiving sensor may vary depending on models.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢃ/36
DIGITAL SIGNAGE
Terminal panel
AC IN
PC D-SUB OUT
UPGRADE
COMPONENT OUT (Y Pb Pr)
CVBS IN
1
2
3
4
5
6
7
8
9
0
!
@
#
$
%
^
&
AC POWER SWITCH
HDMI IN
CVBS OUT
PC AUDIO IN
COMPONENT AUDIO IN (L R)
COMPOSITE AUDIO IN (L R)
HDMI OUT
SPEAKER OUT
PC D-SUB IN
RS-232C OUT
RS-232C IN
COMPONENT IN (Y Pb Pr)
^
&
@
$
%
1
2
5
8
9
0
!
3
4
6
7
#
** The locations of connectors may vary depending on models.
- The items no. 12–17 are optional items.
- When you select the "Source"button on the remote control, the "Source"menu of the "Option" item
is displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢄ/36
DIGITAL SIGNAGE
Remote control
To turn the power on or off.
1
1
2
2
Move up in OSD menu.
To move left or control the volume down in OSD menu.
To move right or control the volume up in OSD menu.
To move down in OSD menu.
Select in OSD menu.
3
4
5
9
3
4
5
6
7
8
9
6
7
Display the menu screen.
8
Close the menu screen.
Convert the input signal.
How to insert batteries
1
2
3
Pull while pressing at rear lid.
Insert the batteries into proper polarities
(+,-).
Use after the lid closed.
10/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
How to Connecting
Kiosk
PC or Source
(Satellite receiver,
Camcorder etc.)
Download from Www.Somanuals.com. All Manuals Search And Download.
11/36
DIGITAL SIGNAGE
How to Connecting
Digital RGB(HDMI)
1
2
1. Please ensure that the power to the device is switched off, then connect each cable one
after another before restoring power.
when connect HDMI to HDMI cable
when connect DVI to HDMI cable
1
2
– must utilize device with DVI signal output from peripheral device
2. Connect the power code to the product.
3. Turn on the power of the product and peripheral device. Screen shows up within 10 seconds.
4. Select "HDMI" input by pressing "SOURCE" on OSD button or remote control.
– HDMI input gives better video quality than analog RGB input.
– Both HDMI and analog RGB support plug and play.
1ꢀ/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
Support timing for
HDMI
Horizontal frequency
(KHz)
Vertical frequency
(Hz)
NO
Resolution
480p
576p
640 x 480p
720 x 576p
1280 x 720p
1920 x 1080i
31.47
60
50
1
2
720p
50 / 60
50 / 60
59.94
60.32
60
3
1080i
4
640 x 480
640 x 480
1024 x 768
1360 x 768
1360 x 768
1600 x 1200
1920 x 1080
1080p
5
37.88
6
48.36
7
47.70
60
8
64.00
60
9
75.00
60
10
11
12
67.50
60
1920 x 1080p
60
9, 10, 11 and 12 are only for Full HD
!
Download from Www.Somanuals.com. All Manuals Search And Download.
13/36
DIGITAL SIGNAGE
How to Connecting analog
RGB (PC D-SUB)
1. Please ensure that the power to the device is switched off, then connect each cable one
after another before restoring power.
2. Connect D-SUB to D-Sub cable. Then tighten the screw of the cable after connecting PC
D-SUB.
3. Connect the power cord to the product.
4. Turn on the power of the product and PC . The screen will appear within 10 seconds.
5. Select "PC" input by pressing "SOURCE" on OSD button or remote control.
– HDMI input gives better video quality than analog RGB input.
– Both HDMI and analog RGB support plug and play.
1ꢁ/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
Support timing for PC
Horizontal frequency
(KHz)
Vertical frequency
(Hz)
NO
Resolution
640 x 480
800 x 600
31.47
37.88
48.36
47.71
64.00
75.00
67.50
59.94
60.32
60.00
60.00
60.00
60.00
60.00
1
2
3
4
5
6
7
1024 x 768
1360 x 768
1280 x 1024
1600 x 1200
1920 x 1080
5, 6 and 7 are only for Full HD
!
Download from Www.Somanuals.com. All Manuals Search And Download.
15/36
DIGITAL SIGNAGE
How to Connecting the
component (Option)
1. Please ensure that the power to the device is switched off, then connect each cable one
after another before restoring power.
2. Connect the component cables to Y, Pb, and Pr correctly.
Connect BNC cable and tighten.
3. Connect the power cord to the product.
4. Turn on the power of the product and peripheral device .
The screen will appear within 10 seconds.
5. Select "COMPONENT" input by pressing "SOURCE" on OSD button or remote control.
16/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
Support timing for
component & AV
Horizontal frequency
(KHz)
Vertical frequency
(Hz)
NO
Resolution
1
ꢁꢃ0i
ꢂꢀ0 x ꢁꢃ0i
6ꢁ0 x ꢁꢃ0p
ꢁꢀ0 x ꢁꢃ0p
ꢂꢀ0 x 5ꢂ6i
5ꢄ.ꢄꢁ / 60
5ꢄ.ꢄꢁ / 60
5ꢄ.ꢄꢁ / 60
50
ꢀ
ꢁꢃ0p
3
ꢁ
5
6
ꢂ
5ꢂ6i
5ꢂ6p
ꢂꢀ0p
10ꢃ0i
10ꢃ0p
ꢂꢀ0 x 5ꢂ6p
1ꢀꢃ0 x ꢂꢀ0p
1ꢄꢀ0 x 10ꢃ0i
1ꢄꢀ0 x 10ꢃ0p
50
5ꢄ.ꢄꢁ / 60 / 50
5ꢄ.ꢄꢁ / 60 / 50
60 / 50
7 is only for Full HD
!
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢂ/36
DIGITAL SIGNAGE
How to Connecting the
the video (Option)
1. Please ensure that the power to the device is switched off, then connect each cable one after
another before restoring power.
2. Connect video cable and BNC cable, and then tighten.
3. Connect the power cord to the product.
4. Turn on the power of the product and peripheral device .
The screen will appear within 10 seconds.
5. Select AV input by pressing "SOURCE" on OSD button or remote control.
1ꢃ/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
Adjusting OSD and
explanation of its
Users can automatically adjust the picture mode according to the input mode.
Picture
Picture
function
How to Select the Picture
Mode
Picture Mode
Custom
:
:
Custom
Dynamic
Standard
Movie
Picture Mode
Custom
Colour Tone
Size
:
:
Custom
High
Colour Tone
Size
Middle
Low
NR
:
Mild
PC
:
Film Mode
:
NR
U
Adjust
Menu
U
Adjust
Menu
Enter
Enter
1. Press Menu button. Menu items appear on the screen.
2. Press ↲ button to select "Picture" Icon. "Picture mode" is highlighted.
3. Press ▶ or ↲ buttons to select "Picture mode".
4. The menu changes in the following order.
AV/Component input : Custom -> Dynamic -> Standard -> Movie -> Mild
PC/HDMI Input : Custom -> High -> Middle -> Low
5. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu.
- Custom : When the user wants to set the values directly.
- Dynamic : Clear display
- Standard : Most video contents are appropriate to this mode.
- Movie : When watching a movie
- Mild : Soft display.
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢄ/36
DIGITAL SIGNAGE
Users can manually adjust their desired picture
How to Set the Desired
Picture
1. Press Menu button.
Custom
Menu items appear on the screen.
2. Press ↲ button to select "Picture" Icon.
"Picture mode" is highlighted.
3. Press ▲ / ▼ buttons to move to "Custom" and press ▶or
↲ buttons to select "Custom".
Brightness
Contrast
Colour
:
:
:
:
:
40
80
50
50
60
Tint
Sharpness
4. Select required option by pressing the ▲ / ▼ or ↲ button,
then Press◀ / ▶ button to adjust.
5. Press EXIT button to escape OSD MENU or press MENU
button to return to the previous menu.
U
Move
Menu
Adjust
- Brightness : Adjust the brightness of the entire picture.
- Contrast : Adjust the brightness and darkness of the object and backgrounds.
- Colour : Adjust colors into deeper or lighter colors.(not operational in PC and HDMI mode)
- Tint : Adjust colors naturally.(not operational in PC, HDMI and component mode)
- Sharpness : Adjust the clarity of object outlines.(not operational in PC and HDMI mode)
ꢀ0/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
Users can adjust Color as users want.
How to Select a Colour Tone
1. Press Menu button.
Colour Tone
Menu items appear on the screen.
2. Press ↲ button to select "Picture" Icon.
"Picture Mode" is highlighted.
Colour Tone
Red
:
:
:
:
Custom
50
Green
Blue
50
3. Press ▲ / ▼ buttons to move to "Colour Tone"
50
4. Press
▶
or
↲
buttons to select "Colour Tone" .
5. Press ▲ / ▼ buttons, then the menu changes in the
following order.
Custom -> Cool2 -> Cool1 -> Normal -> Warm1 -> Warm2
U
Move
Menu
Enter
6. Press EXIT button to escape OSD menu or press MENU button to return to the previous menu.
- Custom : When the user wants to set the degree of RGB directly.
- Cool : For cool colors with bluish tone.
- Normal : For a general Colour Tone.
- Warm : For warm colors with reddish tone.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ1/36
DIGITAL SIGNAGE
How to Set the Display Size
Users can adjust the display scale as they want
Picture
Picture
Picture Mode
Custom
:
:
Auto size
Wide
Picture Mode
Custom
Colour Tone
Size
:
:
Colour Tone
Size
Panorama
Zoom
4 : 3
Wide
NR
:
4 : 3
PC
:
Film Mode
:
14 : 9
NR
U
Adjust
Menu
U
Adjust
Menu
Select
Enter
1. Press Menu button. Menu items appear on the screen.
2. Press ↲ button to select "Picture" Icon. "Picture Mode" is highlighted.
3. Press ▲ / ▼ buttons to move to "Size".
4. Press ◀ / ▶ or ↲ buttons and press ▲ / ▼ then the mode change in the following order.
AV/Component Inputs : Auto Size ->Wide -> Panorama -> Zoom -> 4 : 3 -> 14 : 9
PC input : Wide -> 4 : 3
DVI input : 4 : 3 -> Wide -> 1 : 1
5. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu.
- Auto Size - Screen size adjust automatically by screen signal.
- Wide - General broadcast picture is adjusted to 16:9.
- Panorama - Picture enlarged to 16:9 format, letter box format.
- Zoom - Zoom in 16:9 in vertical direction
- 4 : 3 - 4 : 3 general picture size
- 14 : 9 - 14 : 9 picture size
- 1 : 1 - 1 : 1 real size
ꢀꢀ/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
1. Press Menu button.
Menu items appear on the screen.
2. Press ↲ button to select "Picture" Icon.
"Picture Mode" is highlighted.
3. Press ▲ / ▼ buttons to move to PC and press
▶ or ↲ buttons to select to "PC"
How to set image adjustment
in PC mode
(Supported only in PC mode)
Picture
Auto Adjust
Phase
:
:
:
:
52
16
H-Posilion
V-Posilion
Fiequency
24
-78
4. "Auto Adjust" is high lighted.
5. Press ↲ button to execute the "Auto Adjust"
6. Select the required option by pressing the ◀ / ▶ or ↲
button, then press ◀ / ▶button to adjust
U
Move
Menu
Enter
7. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu.
- Auto Adjust : Horizontal/vertical positions are automatically adjusted.
- Phase : To eliminate the shake of the picture.
- H-Position : To adjust the horizontal position of the picture.
- V-Position : To adjust the vertical position of the picture.
- Frequency : To eliminate the shake of picture.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ3/36
DIGITAL SIGNAGE
User can eliminate noises on the screen in AV/Component/HDMI mode.(Not supported in PC mode)
How to Set Noise
Reduction(NR)
1. Press Menu button.
Picture
Menu items appear on the screen.
2. Press ↲ button to select "Picture" Icon.
"Picture Mode" is highlighted.
3. Press ▲ / ▼ buttons to move to "NR" .
4. Press ◀ / ▶ buttons to select to "NR".
5. Press ▲ / ▼ or ↲ buttons to set "On/Off".
6. Press EXIT button to escape OSD MENU or press MENU
button to return to the previous menu.
Picture Mode
Custom
:
:
Colour Tone
Size
Off
On
NR
:
Film Mode
:
U
Adjust
Menu
Enter
How to Select the Audio
Mode
Users can adjust sound mode automatically as they want.
1. Press Menu button. Menu items appear on the screen.
Sound
2. Press ▲ / ▼ buttons to move to "Sound" Icon.
3. Press ↲ button to select "Sound" Icon. "Mode" is
highlighted.
Mode
:
:
Custom
Standard
Music
Volume
Balance
:
4. Press ▶ or ↲ buttons, to select to Sound mode.
then the menu changes in the following order.
Custom->Standard -> Music -> Movie -> Speech
5. Press EXIT button to escape OSD MENU or press MENU
button to return to the previous menu.
Equalizer
Auto Volume
Sound Mode
:
Movie
Speech
:
U
Adjust
Menu
Enter
- Custom : When the user wants to set the values directly.
- Standard : For the general sound. Most audio contents are appropriate to this mode.
- Music : For enjoying original sound.
- Movie : Grandiose sound.
- Speech : Clear sound.
ꢀꢁ/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
Users can adjust sound mode automatically as they want.
How to Adjust the Desired
Audio Mode
Sound
Sound
Mode
:
:
Custom
34
10KHz
3KHz
50
50
50
50
50
Volume
Balance
:
L50 R50
Equalizer
Auto Volume
Sound Mode
:
1KHz
Off
300Hz
100Hz
:
Stereo
U
Move
L
Adjust
Menu
U
Move
Menu
Enter
1. Press Menu button. Menu items appear on the screen.
2. Press ▲ / ▼ buttons to move to "Sound" Icon.
3. Press ↲ button to select "Sound" Icon. "Mode" is highlighted.
4. Press ▲ / ▼ buttons to move to Balance or Equalizer
"
"
"
"
.
5. Press ↲ buttons to select "Balance" or "Equalizer". Balance or Equalizer menu appears.
6. Select required option by pressing the ▲ / ▼ buttons, then Press ◀ / ▶ buttons to adjust.
7. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu.
- Balance : Adjusts the balance of left and right speakers.
- Equalizer : Adjusts the audio output signal in the desired band.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ5/36
DIGITAL SIGNAGE
This function will automatically give a similar volume size to each channel.
How to Select Auto Volume
1. Press Menu button.
Sound
Menu items appear on the screen.
Mode
:
:
2. Press ▲ / ▼ buttons to move to "Sound" Icon.
3. Press ↲ button to select "Sound" Icon.
"Mode" is highlighted.
4. Press ▲ / ▼ buttons to move to "Auto Volume".
5. Press ◀ / ▶ or ↲ buttons to select "On/Off".
6. Press ▲ / ▼ or ↲ buttons to set to "On/Off".
7. Press EXIT button to escape OSD MENU or press MENU
button to return to the previous menu
Volume
Balance
:
Equalizer
Auto Volume
Sound Mode
:
On
Off
:
U
Adjust
Menu
Enter
Depending on the particular program being broadcast, you can select stereo or mono.
How to Select Sound Mode
Sound
1. Press Menu button.
Menu items appear on the screen.
2. Press ↲ button to select "Sound" Icon.
"Mode" is highlighted.
Mode
:
:
Volume
Balance
:
3. Press ▲ / ▼ buttons to move to "Sound Mode".
Equalizer
Auto Volume
Sound Mode
:
Stereo
Mono L
Mono R
4. Press
▶
or
↲
buttons to select to "Sound Mode".
:
5. Press ▲ / ▼ buttons to select to "Stereo"," Mono L"or
"Mono R.
6. Press exit button to escape OSD MENU or press MENU button
to return to the previous menu
U
Select
Menu
Enter
- Choose "Stereo" for channels that are broadcasting in Stereo.
- Choose "Mono" for channels that are broadcasting in Mono, or if you are having difficultly receiving
a Stereo signal.
ꢀ6/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
Setup
How to Reset
1. Press Menu button.
Menu items appear on the screen.
Reset
Enter
2. Press ↲ button to select "Setup" Icon.
"Reset" is highlighted.
3. Press ▶ or ↲ buttons to select to "Reset".
4. Press ↲ buttons to choose to "Reset".
5. Press EXIT button to escape OSD MENU or press MENU button
to return to the previous menu.
Time
Language
OSD Tone
Key Lock
:
:
:
Menu
Select
When you select "Reset" user setting Value will initialize.
How to Set Clock,Sleep Time,
ON/OFF Time
Time
1. Press Menu button.
Menu items appear on the screen.
2. Press ↲ button to select "Setup" Icon.
"Reset" is highlighted.
3. Press ▲ / ▼ buttons to move to "Time".
4. Press ▶ or ↲ buttons to select "Time".
Time menu appears, then "Clock" is highlighted.
5. Press ◀ / ▶ buttons to move between Hour, Minute and
Press ▲ / ▼ buttons to set Hour, Minute.
Clock
:
:
:
:
:
0 : 0
0 : 0 Off
0 : 0 Off
0
On Timer
Off Timer
On Time Volume
Source
AV
U
Move
Menu
Enter
When the power supply(AC main power) is cut off, the clock is reset to the value before the Timer set.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢂ/36
DIGITAL SIGNAGE
Setup
<Go to step 6 if you need to set the "On or Off Timer">
6. Press ▲ / ▼ buttons to move to "On or Off Timer".
7. Press ▶ or ↲ buttons to select "On or Off Timer" .
8. Press ◀ / ▶ buttons to move between Hour, Minute and on/
off and Press ▲ / ▼ buttons to set Hour, Minute and on/off
<go to step 9 if you need to set the "On Time Volume">
9. Press ▲ / ▼ buttons to move to "On Time Volume".
10. Press ◀ / ▶ buttons to adjust Volume.
Reset
Time
Language
OSD Tone
Key Lock
:
:
:
English
Off
Off
U
Move
Menu
Select
<go to step 11 if you need to set the "Source">
11. Press ▲ / ▼ buttons to move to "Source"
12. Press ▶ or ↲ buttons to select to "Source"
13. Press ▲ / ▼ buttons to set to Source
Choosing the Your
Languages
Setup
1. Press Menu button.
Menu items appear on the screen.
Reset
English
Fiangais
2. Press ↲ button to select "Setup" Icon.
"Reset" is highlighted.
3. Press ▲ / ▼ button to move to "Language" and press
▶ or ↲ button to select to Language.
4. Press EXIT button to escape OSD MENU or press MENU
button to return to the previous menu.
Time
Language
OSD Tone
Key Lock
:
:
:
Deutschland
Ilaliano
Espafiol
Nederland
Suomi
Polski
Cestina
Pyeeknn
U
Adjust
Menu
Enter
ꢀꢃ/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
1. Press Menu button.
Setup
How to set OSD tone
Menu items appear on the screen.
2. Press ↲ button to select "Setup" Icon.
"Reset" is highlighted.
3. Press ▲ / ▼ buttons to move to "OSD Tone"
4. Press ▶ or ↲ buttons to select to "OSD Tone".
5. Press ▲ / ▼ or ↲ buttons to set to "On/Off".
Reset
Time
Language
OSD Tone
Key Lock
:
:
:
Off
On
U
Adjust
Menu
Enter
User can lock the control buttons on the front bottom of the Monitor.
How to Set Key-Lock
Setup
1. Press Menu button.
Menu items appear on the screen.
Reset
2. Press ▲ / ▼ button to move to "Setup" Icon.
3. Press ↲ button to select "Setup" Icon.
"Reset" is highlighted
4. Press ▲ / ▼ buttons to move to "Key Lock".
5. Press ▶ or ↲ buttons to select to "Key Lock".
6. Press ▲ / ▼ or ↲ buttons to set to "On/Off".
7. Press EXIT button to escape OSD MENU or press MENU
button to return to the previous menu.
Time
Language
OSD Tone
Key Lock
:
:
:
Off
On
U
Select
Menu
Enter
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢄ/36
DIGITAL SIGNAGE
How to Set the Multi
Function
Multi
Multi
H Set CounL
V Set CounL
Display Sequence
H Edge ADJ
V Edge ADJ
SET ID
:
:
:
:
:
:
0
0
Multi Function
Heal Control
0
0
0
0
Master
Off
U
Move
Menu
U
Move
Menu
Adjust
Enter
1. Press Menu button.Menu items appear on the screen.
2. Press ▲ / ▼ button to move to "Multi" Icon.
3. Press ↲ button to select "Mutli" Icon. "Mutli Function" is highlighted
4. Press ▲ / ▼ buttons to set up and change the location of the screen to be displyed. H Set Count/
V Set Count/Display Sequence / H Edge ADJ / V Edge ADJ / SET ID/ Master
(Example of installation) install 3x2 with 6 units
Product 1
Product 4
Product 2
Product 5
Product 3
Product 6
30/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
Set up Value
installation item
Product 1
Product 2
Product 3
Product 4
Product 5
Product 6
3
2
1
3
2
2
3
2
3
3
2
4
3
2
5
3
2
6
H Set Count
V Set Count
Display Sequence
H Edge ADJ /
V Edge ADJ
These are the set up value to make up the un-displayed area of Bezel Part.
It can be adjustable according to the contents
It is necessary to control via RS232 communication port on PC. But do not
need to set up or change when they are not controlled by PC
SET ID
Master
You are recommended to use the Master on state only one of products that
you are using
[Cautions]
- In case of connecting the products in series from the input device (HDMI, analog RGB,
component, video etc.), up to about 25 units are possible. But, the number of connecting
devices can be different from the input signal level of each device and thereby amplified
distributor can be needed for this product.
(when over 25 units are connected, the screen may not be displayed properly)
- You are recommended to use the component and progressive frequency of digital RGB in
case of using multi-vision function.
(It may not be displayed properly when using Video input and interlace frequency)
Download from Www.Somanuals.com. All Manuals Search And Download.
31/36
DIGITAL SIGNAGE
How to Set the Heat
Control
"Heat control" allows you set up fan operation according to interior temperture of the product
Multi
Multi
Multi Function
Heal Control
Fan Control
Fan Active Temp
Hysteresis
:
:
:
:
Off
50 °C
50 °C
50 °C
Temprature
U
Move
Menu
U
Move
Menu
Enter
Enter
1. Press Menu button. Menu items appear on the screen.
2. Press ▲ / ▼ button to move to "Multi" Icon.
3. Press ↲ button to select "Multi" Icon. "Multi Function" is highlighted
4. Press ▲ / ▼ buttons to move to "Heat Control".
5. Press ▶ or ↲ buttons to set up and change the Heat Control.
“Fan Control" - AS the fan operation options, following 3 options are available
- Off : Fan is idle in Off status.
- On : Fan is working in On-status.
- Auto : Fan start working when the working temperature is higher than the measured temperature.
• Fan active Temp -set up value to start the fan.
• Hysteresis- tolerance value of fan operation temperature.
• Temperature- measured current temperature by sensor affixed to PCB'A
3ꢀ/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
When the product is not working properly, please check before you call customer center.
Diagnosis
Symptoms
How to solve the problem
It happens not to show the screen noise when the power is on. Therefore it is not a
defect. But if the screen doesn't show up within 5 minutes from turning on, please
contact the customer center.
Screen displays late
after the power is on.
The screen is too dark
or bright?
Adjust the brightness or contrast.
The screen doesn't
show up indicating
"Out of range".
You are using a signal which is outside the operating frequencies of the product
(Unsupported), please change you video signal.
please check the cable connection and the signal generator and contact customer
center.
when the screen is
scrambled.
Automatic switching-on
function is not working
/ the input data were
disapperared when
reboot the system after
setting up the time
Automatic switching-on function is working when the product has been turned
off via remote control or power button on main body. It is because that the set-
up values are deleted when the power cord is unplugged.
Check if the power is on, suspended or is correctly plugged into the outlet. Plug
the power cord of other peripheral device to the outlet that the product is being
connected.
The screen and sound
are not synchronized
Download from Www.Somanuals.com. All Manuals Search And Download.
33/36
DIGITAL SIGNAGE
Symptoms
How to solve the problem
The screen displays
without the sound.
check the volume up and down with remote control and audio connection cable
No sound from either
right speaker or left
speaker.
Confirm the status of the sound balance on OSD menu and check the connection
of speaker cable.
Check if any foreign substances in the sensor and the polarity of battery inserted.
If the batteries are drained, replace them with new batteries.
Remote control
doesn't work.
Set up the resolution referring to frequency table of input terminal. And re-boot
the system as it supports Plug and Play.
PC D-SUB doesn't
work.
Fan on the rear
doesn't work
Check the status of temperature control on OSD menu
The screen doesn't
show up when display
the multi-vision.
check if it is set up to video input. Confirm if Interlace Timing was inputted.
( Refer to the cautions on Page 31 )
•
If any problem unsolved by above diagnosis, please call customer center.
3ꢁ/36
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL SIGNAGE
Specifications
D320ML(I/G) / D400ML / D420ML(I/G/P/T) /
D460ML(I/G/P/T/H) / D468ML(I/G/P/T/H) / D460SL(I)
Model
LCD
D320ML(I/G)/D400ML/
D420ML(I/G/P/T)/
D460ML(I/G/P/T/H)/
D468ML(I/G/P/T/H)/D460SL(I)
1366 x 768 Pixel (HD)
D320ML(I/G) : 697.7 x 392.3 / Pixel pitch 0.51
D400ML : 885.2 x 497.7 / Pixel pitch 0.65
D420ML(I/G/P/T) : 930.3 x 523.0 / Pixel pitch 0.68
D460ML(I/G/P/T/H), D468ML(I/G/P/T/H) : 1018.4x572.5 / Pixel 0.75
D460SL(I) : 1018.4x572.5 / Pixel 0.75
Screen size (HxV/mm)
1360 x 768 @60Hz
Recommended resolution
Input
Digital RGB, Analog RGB, Component(Option), Video(Option), PC Audio L/R,
Component Audio L/R(Option), Video Audio L/R(Option), RS232C
Digital RGB, Analog RGB, Component(Option), Video(Option),
Audio L/R, RS232C
Output
Power
AC 100- 240V 50/60Hz
D320ML(I/G) :170W / D400ML :200W / D420ML(I/G/P/T) :220W /
D460ML(I/G/P/T/H), D468ML(I/G/P/T/H) :260W / D460SL(I) :260W
Consumption (Typical)
Control type
Remote control, key control
•
Above specification may be changed without prior notification for quality improvement.
Download from Www.Somanuals.com. All Manuals Search And Download.
35/36
DIGITAL SIGNAGE
D405ML(I/G)/D407ML(I/G/P/T)/D425ML(I/G/P/T)/D465ML(I/G)/
D467ML(I/G/P/T)/D525ML(I/G)/D825ML(I/G)/ D525SL(I)/D705ML(I/G)/
D705SL(I)/D825SL(I)
Specifications
Model
LCD
D405ML(I/G)/D407ML(I/G/P/T)/
D425ML(I/G/P/T)/D465ML(I/G)/
D467ML(I/G/P/T)/ D525ML(I/G)/
D825ML(I/G)/ D525SL(I)/
D705ML(I/G)/D705SL(I)/
D825SL(I)
1920 x 1080 Pixel (Full HD)
D405ML(I/G) : 885.6 x 498.15 / Pixel pitch 0.46
D407ML(I/G/P/T) : 885.2 x 497.7 / Pixel pitch 0.46
D425ML(I/G/P/T) : 930.25 x 523 / Pixel pitch 0.4845 x 0.4845
D465ML(I/G) : 1018.08 x 572.67 / Pixel pitch 0.53
D467ML(I/G/P/T) : 1018.4 x 572.5 / Pixel pitch 0.53
D525ML(I/G) : 1152.00 x 684.00 / Pixel pitch 0.60
D825ML(I/G) : 1806 x 1015 / Pixel pitch
Screen size (HxV/mm)
D525SL(I) : 1152.00 x 684.00 / Pixel pitch 0.60
D705ML(I/G), D705SL(I) : 1549.44 x 871.56 / Pixel pitch 0.81
D825SL(I) : 1806 x 1015 / Pixel pitch
1920 x 1080 @ 60Hz
Recommended resolution
Input
Digital RGB, Analog RGB, Component(Option), Video(Option), PC Audio L/R,
Component Audio L/R(Option), Video Audio L/R(Option), RS232C
Digital RGB, Analog RGB, Component(Option), Video(Option),
Audio L/R, RS232C
Output
Power
AC 100- 240V 50/60Hz
D405ML(I/G) : 200W / D407ML(I/G/P/T), D425ML(I/G/P/T) : 260W /
D465ML(I/G), D467ML(I/G/P/T) : 250W /
D525ML(I/G), D825ML(I/G) : 320W /
Consumption (Typical)
Control type
D705ML(I/G), D705SL(I) : 800W / D825SL(I) : 900W
Remote control, key control
•
Above specification may be changed without prior notification for quality improvement.
36/36
Download from Www.Somanuals.com. All Manuals Search And Download.
< REMOTE CONTROL / RS232C COMMAND SPEC >
1. SPEED : 9600 Baud/s, 8 bit, No parity, 1 Stop bit.
2. REMOTE CONTROL WAVE FORM
1) Remote Control System Infrared rey system
fosc=455KHZ fc=fosc/2=37.917KHZ
2) Signal code
2-1) Transmission
- One pulse
LEAD CODE
CUSTOM CODE CUSTOM CODE
DATA CODE
DATA CODE
LOW
HIGH
9ms
4.5ms
- Bit Desciption
Bit “0”
Bit “1”
0.56ms
0.56ms
1.125ms
2.25ms
- Flame Interval
Tf
Tf
Tf=108ms 455KHz
Download from Www.Somanuals.com. All Manuals Search And Download.
3. REMOTE CONTROL KEY CODE TABLE
Custom Code : 7788H
DATA LAYOUT
KEY
POWER
MENU
EXIT
DATA
8O
8D
0x80
0x95
0x96
0xAC
0x8C
0x8D
0x8E
0x8F
0x90
8F
8C
9O
AC
8E
96
95
SOURCE
ENTER
UP
DOWN
LEFT
RIGHT
4. COMMAND FORMAT
* SET ID must select from the OSD menu and can't be select through the COMMAND.
* Only one unit can be set as Master unit, select Master ON from the OSD Menu. (DEFAULT OFF)
* For viewing COMMAND from Hyper Terminal windows, One unit must set as MASTER ON
HEADER
SET ID
COMMAND TYPE
END
did:
x- or all-
Command
<Command example>
did:1-pf.
To power off set that is SET ID 1
To factory reset all set
did:all-fr.
To fan on set that is SET ID 2
did:2-fn.
Download from Www.Somanuals.com. All Manuals Search And Download.
5. COMMAND TYPE
Command
pn / pf
Description
Power on / Power off
Fan on / Fan off
Factory reset
fn / ff
fr
Source change ( d:HDMI, p:PC, c:Component, a:AV )
Sub-Brightness 1 step up / down
Red Offset 1 step up / down
sd / sp / sc / sa
sbu / sbd
rou / rod
gou / god
bou / bod
scu / scd
rgu / rgd
ggu / ggd
bgu / bgd
blu / bld
chxvy
Green Offset 1 step up / down
Blue Offset 1 step up / down
Sub-Contrast 1 step up / down
Red Gain 1 step up / down
Green Gain 1 step up / down
Blue Gain 1 step up / down
BACKLIGHT Value 1 step up / down
H Set Count is x, V Set Count is y
H Set window is x, V Set window is y
H Edge ADJ is x, V Edge ADJ is y
Display sequence no is x
nhxvy
ehxvy
x ( figure )
Enable Color Control Mode; Under Cr mode, user can set color value without Header command
ex) ro120 : Red Offset 120, bg100 : Blue Gain 100
cr
ir
Enable Ir Mode, In IR Mode, user can use keyboard buttonsas remote controller
Current power status check. If current power is on(off),
ps
Hyper Terminal windows display “Power On(Power Off)” message.
Current input source status check.
is
If current input source is VGA, Hyper Terminal windows display “VGA Mode” message.
Download from Www.Somanuals.com. All Manuals Search And Download.
6. REMOTE CONTROL KEY CODE TABLE
Key value
Key value
quit ( from Ir mode )
volume up
volume down
mute
q
p
u
n
j
t
power
up
v
r
down
left
picturemode
sleep
c
l
right
enter
menu
exit
sound
k
e
m
x
i
d
s.mode
s
info->display
quit ( from Ir mode )
y
The others
input
7. REMOTE CONTROL KEY CODE TABLE
Command
Description
Change all units 'Display sequence' to 'SET ID'
Set all units to 'H SET Count' = x, 'V SET Count' = y, 'Display sequence' = 'Select to SET ID'
did:all-wn=si.
did:allfst-hxvy
8. CONNECTION
&21752/(5ꢀ3&ꢁꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂꢂ0/ꢂ6HULHVꢂ0RGHO
1
2
3
4
5
1
2
3
4
5
6
7
8
9
6
7
8
9
Rx
Tx
G
Tx
Rx
G
2
3
5
2
3
5
9Pin DIN male
9Pin DIN male
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI IT Service Center
@
Download from Www.Somanuals.com. All Manuals Search And Download.
|