|
PCI 10/100 TX
HYNEC52001
USER GUIDE
Information in this document is subject to change without
notice. All rights reserved. All brand names are registered
trademarks of their respective companies.
Download from Www.Somanuals.com. All Manuals Search And Download.
The HyperNet PCI 10/100 Adapter series is highly integrated and
cost-effective single-chip adapter range that provides 32-bit
performance, PCI bus master capability, and full compliance with
Fast Ethernet 100Base-TX specifications. It also supports full-
duplex operation, making possible 200Mbps of bandwidth with no
additional cost, when connected to an appropriate switch.
The HyperNet PCI 10/100 supports a wide selection of network
operating systems, including Window NT, Windows 98, Windows
95, Windows 3.x and more.
The HyperNet PCI 10/100 Adapter series is a dual-speed adapter
connected to an Ethernet network with a single RJ-45 connection
over unshielded twisted-pair (UTP) cable. The adapter support
10Mbps and 100Mbps Ethernet networks. On power-up, the
adapter can use auto-negotiation to automatically determine line
operating conditions.
!
!
When the adapter is connected to a hub that supports 10Base-T
Ethernet (10Mbps), it switches to a network speed of 10Mbps.
When the adapter is connected to a hub that supports 100Base-
TX Fast Ethernet (100Mbps), it switches to a network speed of
100Mbps.
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
•
PCI 32-Bit bus-mastering architecture speeds data transfers
between your PC and the network, without burdening the
PC’s processor
•
•
Autonegotiation, sensing and switching between 10Mbps and
100Mbps operation
Full Duplex capabilities - Independent receive and transmit
circuits allow for full duplex operation at both 10Mbps and
100Mbps, giving the Card a maximum throughput of 200Mbps
A Single RJ-45 female connector supports both 10Mbps and
100Mbps operation
Supports all major Network Operating Systems, including
Windows 98, Windows 95, Windows NT, Novell NetWare
Configuration is simplified by PCI Plug and Play.
Supports the Desktop Management Interface (DMI) Revision
2.0
•
•
•
•
Download from Www.Somanuals.com. All Manuals Search And Download.
If you do not have each of these items, contact your supplier
before proceeding further.
Static Electricity Warning
Static electricity is accumulated naturally in the human body, and
can be discharged through electrical components by touching
them. This shock can potentially cause permanent internal
damage to the component.
When installing the adapter, please observe the following
precautions:
•
Discharge yourself before commencing by touching a
grounded metal appliance, such as the metal frame of a
computer - while it is tuned off, but still plugged into the wall
socket.
•
•
Hold the adapter or any other boards by their edges only.
Never touch any exposed pins on the adapter.
If possible, install the adapter as soon as you remove it from
its anti-static bag, without putting it down. If you must put it
down, place it on the anti-static bag in which it was packed.
•
Do not place the adapter on any metal surface.
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn OFF the power to the computer to prevent any
accidental damage.
•
•
Remove your computer's cover (refer to your computer
owner's manual).
Select an available PCI expansion slot which supports Bus
Master mode, and remove slot cover. Make a note of the slot
number (if one is printed on the motherboard, next to this
slot).
•
Carefully install the adapter by firmly pressing the card into
the slot which you have chosen, and applying even pressure
until the adapter is completely seated in the slot.
•
•
Fasten the retaining bracket with the screw on the slot cover.
Make sure the adapter is properly aligned.
Replace the system box cover and fasten it.
Connecting to the Network
This section describes how to connect 10Mbps or 100Mbps
network cables to the HyperNet PCI 10/100 series adapter. The
backplate of the HyperNet PCI 10/100 series adapter contains
one RJ-45 connector. This adapter can use auto-negotiation to
automatically determine line operating conditions, such as
10Base-T, 100Base-TX, or a corresponding Full-Duplex mode
based on the type of HUB to which it is connected.
For 10Base-T Ethernet networks:
Use Category 3, 4, or 5 UTP cabling.
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the PCI 10/100 Adapter
PCI Computer with PnP Auto-Configuration
Before installing your Hypertec PCI 10/100 Adapter, try to
establish whether your PC has PCI PnP Auto configuration. In
most cases, the PCI computer will be configured automatically by
the system's BIOS during boot up. The BIOS automatically
assigns the I/O base address and IRQ to the card for proper
operation.
PCI Computer without PnP Self-Configuration
In rare cases, some PCI computers require additional
configuration steps in order to install a PCI adapter. In such an
event we recommend the following:
•
•
•
Make sure that the BIOS is set up correctly. In some PCI
computers, you may need to enable the PCI slot by using the
BIOS setup program, or motherboard jumper changes.
Choose a PCI Slot number to use. Remember the PCI Slot
number where the adapter card was installed, as you need to
set it up as a Bus Master (Enabled).
Examine the reserved interrupts (IRQs) and/or memory
address for ISA adapters. The PCI card will be prevented
from using the same settings as the ISA cards are using.
Download from Www.Somanuals.com. All Manuals Search And Download.
of BIOS for use with PCI adapters.
Checking card operation
The Adapter provides two LEDs to indicate operation:
FDX (Full Duplex)
Steady Green Light indicates
the connection to a full duplex
switch port.
LK/ACT (Link/Activity)
Steady Green Light indicates
an active connection between
the adapter and the
hub/switch port.
Flashing Green Lights
indicates data transmission
LIN K /A C T (A ctivity )
FD X (Full-D u p lex)
Figure 2. PCI 10/100Base series Adapter LED indicators
Download from Www.Somanuals.com. All Manuals Search And Download.
For more details of the loading procedure for software drivers, please
execute the HELP8139.EXE program.
If at any time during installation you experience difficulties, please
contact Hypertec Technical Support on +44 1488 686844 (01488 686844
in the UK).
Download from Www.Somanuals.com. All Manuals Search And Download.
The setup program can view current configuration and run
diagnostics on the HyperNet PCI 10/100 series Adapters. This
testing includes three separate procedures:
•
•
•
View Current Configuration
Setup New Configuration
Run diagnostics Menu
Adapter cannot connect to the network
Make sure that the cable is installed properly. The network cable
must be securely attached to all connections. If the cable is
attached, but the problem persists, try using a different cable.
Note: If you're operating at 100 Mbps, you must use UTP
Category 5 wiring.
If you're directly connecting two workstations (no hub), use a
cross-over cable.
•
Check the LED lights on the adapter. These lights help to
indicate if there's any problem with the connector, cables, or
hub.
•
•
•
The Link LED light is ON when the adapter receives a Link
pulse from the Ethernet Hub or card.
If the Link LED light is off, it may be caused by a bad
connector, bad cable, or any problem with the hub.
The ACT LED light is flashing when there's transmitting or
receiving activity on the network.
Download from Www.Somanuals.com. All Manuals Search And Download.
T D
R D
R D
4
5
6
7
8
1 2 3 4 5 6 7 8
Figure A-1 show the PCI 10/100BaseTX RJ-45 Connector Pin
Assignments
Note: The Pin assignments are identical for 10Base-T and
100Base-TX, by using UTP cable.
Network cabling
In Fast Ethernet 100Base-TX, the cable, quality, distance, and
connectors must comply with the EIA/TIA 568 “Commercial
Building Wiring Standard”.
IEEE 802.3u Specification: The 100Base-TX specification
supports 100 Mbps transmission over two of four pairs of twisted
Ethernet wiring. In two pair wiring, one pair of wires is used for
transmission, and the second is used for collision detection and
receiving.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Figure B-1 show the Unshielded Twisted Pair Wiring
Note: For the 10/100 Mbps twisted pair cable, pins 1&2 must be
a pair and pins 3&6 must also be a pair. Each pin must connect
straight to the other end of the
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Length - 125.4mm
Height - 42.3mm
LED Indicators:
Full Duplex, Link/Activity
Operating Temperature:
0°-55°C (32°F-131°F)
Operating Humidity:
0% - 90% non-condensing
Storage:
-20°C-65°C (-4°F–149°F)
Ethernet Protocols:
IEEE 802.3U (Fast Ethernet, 100Base-TX)
IEEE 802.3 (Ethernet, 10Base-T)
Data Transfer Rate:
100 or 10 Mbit/sec
200 or 20Mbit/sec Full Duplex
Connector:
Unshielded RJ-45 female connector.
EMI:
FCC Class B
European standards EN55022 and EN50082-1
Download from Www.Somanuals.com. All Manuals Search And Download.
disaster, misuse, abuse or non-Hypertec modification of the product.
Additional components installed by the dealer or end user are not covered by this
warranty. Apart from the above, no warranty is expressed or implied, including
warranty of merchantability or warranty of fitness for use for a particular purpose.
The liability of Hypertec is limited to the repair or replacement of the product with a
functionally equivalent or better product. Hypertec is not liable for any accidental,
general, special, exemplary or consequential damages resulting from any product
failure, even if Hypertec has been advised of the possibility of such damages.
Hypertec Limited
Units 1-3 Station Road
Hungerford, Berkshire RG17 0DY
Ph:
Fax:
+44 (0)1488 686844
+44 (0)1488 686845
Web:
Email:
Download from Www.Somanuals.com. All Manuals Search And Download.
|