2007
4213 Utility
Vehicle
Gasoline
Owner’s Manual
HUV 4213-G
HUV 4213-GXP
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE
The Husqvarna® Limited Two Year Warranty for 2007 Transportation and Utility Vehicles and California Emis-
sion Control Warranty Statement appear on the last pages of this manual. No other warranties, express or
implied, are contained herein. Please complete and return the warranty registration card included in this man-
ual.
Husqvarna is not liable for errors in this manual or for incidental or consequential damages that result from the
use of the material in this manual.
This manual contains proprietary information that is protected by copyright. All rights are reserved. No part of
this manual may be photocopied, reproduced, or translated to another language without the written consent
of Husqvarna.
The information contained in this document is subject to change without notice.
Husqvarna reserves the right to change specifications and designs at any time without notice and without the
obligation of making changes to units previously sold.
These vehicles do not conform to Federal Motor Vehicle Safety Standards for automobiles or to FMVSS 500
for low-speed vehicles, and are not equipped for operation on public streets, roads, or highways.
Husqvarna Forest and Garden
7349 Statesville Rd.
Charlotte, NC 28269
USA
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
FOREWORD
Thank you for choosing Husqvarna, a world leader in outdoor products. You have chosen the finest utility
vehicle on the market. Please protect your investment and ensure that your Husqvarna vehicle provides years
of reliable, superior performance by reading and following the maintenance instructions in this manual.
Your comfort and safety are important to us, so we urge you to read and follow the step-by-step operating
instructions and safety precautions in this manual. These instructions must be followed in order to avoid the
risk of severe personal injury. If you rent or loan your vehicle to others, we recommend that you ask them to
read this manual before they operate the vehicle.
Husqvarna products are backed by a customer support system designed to offer you fast, courteous service.
In the event that your Husqvarna vehicle needs repairs or service, we recommend that your local authorized
Husqvarna representative perform them. For the name and address of the Husqvarna representative nearest
Husqvarna, Attention: Marketing Services, 7349 Statesville Rd., Charlotte, NC 28269 USA. Your local autho-
rized Husqvarna representative can also provide technical advice, parts, and service manuals.
We hope you will consider this owner’s manual a permanent part of your Husqvarna vehicle. If you sell the
vehicle, please include the manual so that the next owner will have the important operating, safety, and main-
tenance information it contains. Translated owner’s manuals can be downloaded from the Husqvarna web
vehicle. These parts can be purchased from your authorized Husqvarna dealer.
REGULAR MAINTENANCE ITEMS
PERIODIC MAINTENANCE ITEMS
Engine Oil Filter
(P/N 603 00 00-06)
Battery
(P/N 603 00 00-02)
Engine Air Filter
(P/N 603 00 00-04)
Spark Plug O.H.V.
(P/N 603 00 00-07)
Engine Fuel Filter
(P/N 603 00 00-08)
Spring Tune-Up Kit
(P/N 603 00 00-05)
Battery Terminal Protector Spray
(P/N 603 00 00-03)
Dry Moly Lube
(P/N 603 00 00-01)
Page 2
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Vehicle Feature Identification ....................................................................................................................
Safety Details ............................................................................................................................................
General Warnings ......................................................................................................................................
Model Identification ....................................................................................................................................
7
8
9
Controls and Indicators .............................................................................................................................. 10
Seat Latch and Adjustment ....................................................................................................................... 14
Pre-Operation and Daily Safety Checklist ................................................................................................. 14
Driving Instructions .................................................................................................................................... 16
Bed Latch and Prop Rod ........................................................................................................................... 18
Front Shock Absorbers .............................................................................................................................. 19
Loading and Unloading .............................................................................................................................. 19
Towing with the Vehicle ............................................................................................................................. 20
Transporting on a Trailer ........................................................................................................................... 20
Storage ...................................................................................................................................................... 21
Maintenance .............................................................................................................................................. 23
Periodic Service Schedule ......................................................................................................................... 24
Periodic Lubrication Schedule ................................................................................................................... 26
Master Cylinder ......................................................................................................................................... 27
Engine Oil .................................................................................................................................................. 27
Fueling Instructions ................................................................................................................................... 31
Battery ....................................................................................................................................................... 32
Cleaning the Vehicle .................................................................................................................................. 34
Accessories ............................................................................................................................................... 34
Subsequent Owner Registration ................................................................................................................ 35
Vehicle Specifications ................................................................................................................................ 36
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Vehicle Feature Identification
HUV4213-G
DIFFERENTIAL
LOCK CONTROL
DECAL
OPERATING
INSTRUCTIONS DECAL
DRIVER/PASSENGER WARNING
DECAL
KEY SWITCH
BED LOAD
WARNING DECAL
UNDERAGE
WARNING DECAL
FUEL SHUT-OFF
VALVE
(ON TOP OF
FUEL TANK)
LAMP
SWITCH
FUEL GAUGE/
HOUR METER
LOW OIL
WARNING
LAMP
SERIAL
NUMBER
CRUSH AREA
DECAL
ROTATING PARTS
DECAL
(TOP OF PASSENGER SIDE FENDER)
BRAKE
PEDAL
BED
LATCH
ACCELERATOR
PEDAL
(UNDER SEAT
SUPPORT)
VEHICLE LOADING DECAL
Page 4
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Vehicle Feature Identification
HUV4213-G
BED LATCH
WARNING DECAL
GASOLINE WARNING DECAL
CHOKE
(ON PASSENGER SIDE
SEAT SUPPORT)
PARK BRAKE
(DOTTED LINE)
FORWARD/REVERSE
HANDLE
TRAILER HITCH
DECAL
(ON FRONT AND REAR
RECEIVER HITCHES)
ROTATING PARTS AND
HOT MANIFOLD DECAL
RECEIVER
HITCH
(SHOWN WITH
OPTIONAL
TUBE BUMPER)
WINCH CABLE
WARNING DECAL
(FOR VEHICLES WITH WINCH ACCESSORY)
(ON STARTER/GENERATOR
AND ENGINE)
DIODE
WIRING DECAL
(ON SEAT SUPPORT PANEL)
(ON FRAME ABOVE DIODE)
FRAME GROUND AND
GOVERNOR WARNING DECAL
(ON FRAME)
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
HUV4213-GXP
DIFFERENTIAL
LOCK CONTROL
DECAL
OPERATING
INSTRUCTIONS DECAL
DRIVER/PASSENGER WARNING
DECAL
KEY SWITCH
BED LOAD
WARNING DECAL
UNDERAGE
WARNING DECAL
FUEL SHUT-OFF
VALVE
(ON TOP OF
FUEL TANK)
LAMP
SWITCH
FUEL GAUGE/
HOUR METER
LOW OIL
WARNING
LAMP
SERIAL
NUMBER
CRUSH AREA
DECAL
ROTATING PARTS
BRAKE
PEDAL
DECAL
BED
LATCH
(TOP OF PASSENGER SIDE FENDER)
ACCELERATOR
PEDAL
(UNDER SEAT
SUPPORT)
VEHICLE LOADING DECAL
Page 6
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
HUV4213-GXP
BED LATCH
WARNING DECAL
GASOLINE WARNING DECAL
CHOKE
(ON PASSENGER SIDE
SEAT SUPPORT)
PARK BRAKE
(DOTTED LINE)
FORWARD/REVERSE
HANDLE
TRAILER HITCH
DECAL
(ON FRONT AND REAR
RECEIVER HITCHES)
ROTATING PARTS AND
HOT MANIFOLD DECAL
RECEIVER
HITCH
WINCH CABLE
WARNING DECAL
(FOR VEHICLES WITH WINCH ACCESSORY)
(ON STARTER/GENERATOR
AND ENGINE)
DIODE
WIRING DECAL
(ON SEAT SUPPORT PANEL)
(ON FRAME ABOVE DIODE)
FRAME GROUND AND
GOVERNOR WARNING DECAL
(ON FRAME)
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Practice Safety
WARNING
!
Rotating Parts
Safety signs like you see above may at first seem shocking, but their impact is mild
compared with the reality of severe personal injury.
Your safety and satisfaction are of the utmost importance to Husqvarna. That is why
before operating the vehicle, we urge you to review the information in this manual.
Understand and become familiar with the DANGER, WARNING and CAUTION statements
and procedures it contains, along with the safety decals that are affixed to your
vehicle.
Take time to understand the language of safety. It is a language that can save your life.
PROPOSITION 65 - STATE OF CALIFORNIA
This product contains or emits chemicals or substances that have been determined
by the state of California to cause cancer and birth defects or other reproductive harm.
Page 8
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Details
SAFETY DETAILS
ý WARNING
• This owner’s manual should be read completely before attempting to drive or service the
vehicle. Failure to follow the instructions in this manual could result in property damage,
severe personal injury, or death.
It is important to note that some vital statements throughout this manual and on the decals affixed to the vehi-
cle are preceded by the words DANGER, WARNING, or CAUTION. For your protection, we recommend that
you take special notice of these safety precautions. Safety precautions are essential and must be followed.
If any of the operation or warning decals on the vehicle become damaged, have been removed, or cannot be
easily read, they should be replaced immediately to avoid possible property damage, personal injury, or
death. Contact your Husqvarna dealer.
ý DANGER
• A DANGER indicates an immediate hazard that will result in severe personal injury or death.
ý WARNING
• A WARNING indicates an immediate hazard that could result in severe personal injury or
death.
ý CAUTION
• A CAUTION with the safety alert symbol indicates a hazard or unsafe practice that could
result in minor personal injury or product or property damage.
CAUTION
• A CAUTION without the safety alert symbol indicates a potentially hazardous situation that
could result in property damage.
AS SEEN FROM
PASSENGER SIDE
OF VEHICLE
FR
ONT
OF VEHICLE
Remove
negative
cable first.
DISCONNECT BATTERY CABLES
BEFORE WORKING ON VEHICLE
Figure 1 Battery Cable Removal
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
General Warnings
GENERAL WARNINGS
The following safety statements must be heeded whenever the vehicle is being operated, repaired, or ser-
viced. Vehicle feature identification information is also included beginning on page 4. Other specific safety
statements appear throughout this manual and on the vehicle.
ý
DANGER
• Battery – Explosive gases! Do not smoke. Keep sparks and flames away from the vehicle and
service area. Ventilate when charging or operating vehicle in an enclosed area. Wear a full
face shield and rubber gloves when working on or near batteries.
• Gasoline – Flammable! Explosive! Do not smoke. Keep sparks and flames away from the
vehicle and service area. Service only in a well-ventilated area.
• Do not operate gasoline vehicle in an enclosed area without proper ventilation. The engine
produces carbon monoxide, which is an odorless, deadly poison.
• A Husqvarna vehicle will not provide protection from lightning, flying objects, or other storm-
related hazards. If caught in a storm while driving a Husqvarna vehicle, exit the vehicle and
seek shelter in accordance with applicable safety guidelines for your location.
ý WARNING
• Follow the procedures exactly as stated in this manual, and heed all DANGER, WARNING, and
CAUTION statements in this manual as well as those on the vehicle.
• Do not leave children unattended on vehicle.
• Prior to leaving the vehicle unattended or servicing the vehicle, set the park brake, place the
Forward/Reverse handle in the NEUTRAL position, turn the key switch to the OFF position,
and remove the key. Chock the wheels when servicing the vehicle.
• Improper use of the vehicle or failure to properly maintain it could result in decreased vehicle
performance, severe personal injury, or death.
• Any modification or change to the vehicle that affects the stability or handling of the vehicle,
or increases maximum vehicle speed beyond factory specifications, could result in severe
personal injury or death.
• Check the vehicle for proper location of all vehicle safety and operation decals and make sure
they are in place and are easy to read.
• For vehicles with cargo beds, remove all cargo before raising the bed or servicing the vehicle.
If the vehicle is equipped with a prop rod, ensure that it is securely engaged while bed is
raised. Do not close bed until all persons are clear of cargo bed area. Keep hands clear of all
crush areas. Do not drop cargo bed; lower gently and keep entire body clear. Failure to heed
this warning could result in severe personal injury or death.
• Only trained technicians should service or repair the vehicle. Anyone doing even simple
repairs or service should have knowledge and experience in electrical and mechanical repair.
The appropriate instructions must be used when performing maintenance, service, or
accessory installation.
• To avoid unintentionally starting the vehicle:
- Disconnect battery cables, negative (–) cable first (Figure 1).
- Disconnect the spark plug wire from the spark plug.
Page 10
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Identification
ý WARNING
• Frame ground – Do not allow tools or other metal objects to contact frame when
disconnecting battery cables or other electrical wiring. Do not allow a positive wire to touch
the vehicle frame, engine, or any other metal component.
• Wear safety glasses or approved eye protection when servicing the vehicle. Wear a full face
shield and rubber gloves when working on or near batteries.
• Do not wear loose clothing or jewelry such as rings, watches, chains, etc., when servicing the
vehicle.
• Use insulated tools when working near batteries or electrical connections. Use extreme
caution to avoid shorting of components or wiring.
MODEL IDENTIFICATION
The serial number of each HUV4213 vehicle is printed on a bar code decal mounted on the frame directly
above the accelerator pedal (Example: SH0501-583947) (Figure 2). There is also a second serial number
decal mounted on the front body frame behind the instrument panel. The instrument panel must be removed
to view this decal. See following NOTE.
NOTE: Have the vehicle serial number available when ordering parts or making inquiries.
SERIAL NUMBER
7349 STATESVILLE RD.
SH0501-583947
CHARLOTTE, NC 28269
Figure 2 Serial Number
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Indicators
CONTROLS AND INDICATORS
ý WARNING
• Before allowing anyone to drive the vehicle, make sure the driver is familiar with all controls
and operating procedures.
• Do not tamper with the governor. Doing so will void the warranty, as well as damage the
engine and other components, and could result in property damage, personal injury, or death
due to unsafe speeds.
• Do not shift the Forward/Reverse handle while the vehicle is in motion.
• Engine must be at idle before shifting the Forward/Reverse handle. Failure to do so may result
in injury to inattentive passengers and (or) damage to the vehicle.
• To avoid unintentionally starting or rolling the vehicle, set the park brake, place the Forward/
Reverse handle in the NEUTRAL position, turn the key switch to the OFF position, and remove
the key when leaving the vehicle.
• With the differential lock engaged, vehicle turning functions are greatly reduced. To prevent
loss of vehicle control when differential lock is engaged, do not operate vehicle at speeds
greater than half throttle and use caution when attempting to turn the vehicle.
KEY SWITCH
The key switch is mounted on the instrument panel to the right of the steering column (Figure 3). It has three
positions: OFF, ON, and START. To start the vehicle, place the Forward/Reverse handle in the NEUTRAL
position and turn the key past the ON position to the START position and hold until the engine is running
smoothly. Release the key and it will return to the ON position and the engine should idle.The engine will con-
tinue to idle until the key is turned to the OFF position. See following WARNING, CAUTION and NOTE.
Figure 3 Key Switch
ý WARNING
• Moving parts! Keep clear of the engine compartment while the engine is running.
Page 12
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Indicators
CAUTION
• Do not “rev” the engine for long periods of time while the Forward/Reverse handle is in the
NEUTRAL position. Failure to heed this caution could result in damage to the unitized
transaxle.
• Do not shift the Forward/Reverse handle while the accelerator pedal is pressed. Shift the
handle only when the vehicle is at a complete stop. Failure to heed this caution could result in
damage to the unitized transaxle.
NOTE: The key can be removed only when the key switch is in the OFF position.
FORWARD/REVERSE CONTROL
The Forward/Reverse handle is located on the seat support panel (Figure 4). The handle has three distinct
positions: F (FORWARD), N (NEUTRAL), and R (REVERSE). Rotate the handle towards the driver (FOR-
WARD) to operate the vehicle in the forward direction, or towards the passenger (REVERSE) to operate the
vehicle in reverse. The engine can be started only when the handle is in the straight up position (NEUTRAL).
The engine must be at idle before shifting the Forward/Reverse handle. See WARNING and CAUTION on
F
N
R
Figure 4 Forward/Reverse Handle
Husqvarna vehicles operate at a reduced speed in reverse. The reverse buzzer will sound as a warning when
the Forward/Reverse handle is in the REVERSE position.
ACCELERATOR PEDAL
With the engine running and the Forward/Reverse handle in the FORWARD or REVERSE position, vehicle
speed will increase as the accelerator pedal is pressed. When the accelerator pedal is released, it will return
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Indicators
BRAKE PEDAL
The brake pedal is the large pedal on the left with the word STOP molded into it (Figure 5). To slow or stop
Figure 5 Accelerator and Brake Pedal
Figure 6 Brake Pedal
PARK BRAKE
The park brake handle is located between the driver and passenger seats. To engage the park brake, first
apply pressure to the brake pedal, and then pull up on the park brake handle until handle latches into place.
To disengage, pull up on the handle and press the button on the end of the handle. Push handle down. See
following WARNING.
ý WARNING
• The park brake has multiple locking positions and should be firmly locked to prevent the
vehicle from rolling.
CHOKE
The choke is located on the seat support panel below and to the left of the driver’s left knee. If the vehicle is
hard to start in cool or cold temperatures, activate choke: Pull the choke handle out to activate. Release the
WARNING
Figure 7 Choke
Figure 8 Differential Lock
Page 14
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Indicators
DIFFERENTIAL LOCK
ý WARNING
• With the differential lock engaged, vehicle turning functions are greatly reduced. To prevent
loss of vehicle control when differential lock is engaged, do not operate vehicle at speeds
greater than half throttle and use caution when attempting to turn the vehicle.
• Disengage differential lock on paved surfaces.
The differential lock is used to provide better traction at the rear wheels when necessary. Engaging the differ-
1. To engage the differential lock, slow the vehicle to no more than half throttle and pull differential lock han-
dle toward the back of the vehicle. The differential lock will engage when power to both rear wheels is
required.
2. To disengage the differential lock, come to a complete stop, then push lever toward front of vehicle.
LOW OIL WARNING LAMP
The vehicle is equipped with a low oil warning lamp, located on the instrument panel just to the right of the
steering column and key switch (Figure 9). If the warning lamp comes on, oil should be checked and added
to the engine as necessary before continuing to use the vehicle. The vehicle should never be driven when the
low oil warning lamp remains on. If the warning lamp goes on and off, the vehicle may be driven, but oil should
be added at the first opportunity. If the oil level is correct and the warning lamp stays on, have a trained tech-
nician check the vehicle. See following CAUTION.
CAUTION
• Failure to add oil immediately when the low oil warning lamp stays on may result in
permanent engine damage.
Figure 9 Low Oil Warning Lamp
FUEL GAUGE/HOUR METER
The fuel gauge and hour meter are housed together at the lower left corner of the instrument panel. The fuel
gauge operates when the key switch is in the ON position, and allows the operator to monitor the fuel level in
the vehicle. The hour meter operates only when the engine is running, and should be used by the trained
technician to track vehicle usage and determine when periodic service procedures are required. See Peri-
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Seat Latch and Adjustment
HEADLAMP CONTROL
The headlamp control is located on the instrument panel between the fuel gauge/hour meter and steering col-
umn. Pull the headlamp control knob out to turn the headlamps on and push the knob in to turn the headlamps
off.
NOTE: Using the headlamps for extended periods of time without the engine running, or with the engine
idling, will discharge the battery.
LAMP BAR CONTROL
The lamp bar control is a toggle switch located on the instrument panel above and slightly left of the headlamp
control knob. Place the toggle switch in the upper position to illuminate the lamp bar lamps and in the lower
position to turn the lamp bar lamps off.
SEAT LATCH AND ADJUSTMENT
The seats are hinged to allow easy access to the engine compartment. A latch at the rear of each seat bottom
keeps the seat from moving on its hinges while the vehicle is in operation. To disengage the latch, grasp the
seat back and pull firmly in a forward/upward direction until the latch releases. To engage the seat latch, push
down firmly on the seat back until the seat locks into place. See following WARNING.
The bucket seats are adjustable and can be moved forward or backward to accommodate the driver or pas-
senger. To adjust a seat:
1. Remove the seat from the vehicle.
2. Remove the four bolts and washers from the bottom of the seat mounting plate.
3. Align the mounting plate holes with holes in the seat to achieve the desired seat position.
4. Install washers and bolts and tighten to 96 in-lb (10.8 N·m).
5. Install seat in the vehicle.
ý WARNING
• Make sure seat hinges and latch are securely engaged before operating vehicle.
PRE-OPERATION AND DAILY SAFETY CHECKLIST
Each Husqvarna vehicle has been thoroughly inspected and adjusted at the factory; however, upon receiving
your new vehicle(s), you should become familiar with its controls, indicators, and operation. Carefully inspect
each vehicle to ensure that it is in proper working condition before accepting delivery.
Use the following checklist as a guide to inspect the vehicle. This checklist should be used daily to ensure that
the vehicle is in proper working condition and in conjunction with the Periodic Service Schedule on page 26.
Any problems should be corrected by a Husqvarna distributor/dealer or a trained technician.
• General: All the parts should be in place and properly installed. Be sure that all nuts, bolts, and screws
are tight. Check hose clamps for tight fit and the starter belt for tightness.
• Safety and information decals: Check to ensure that all safety and information decals are in place.
• Tires: Check for proper tire pressure. Visually inspect tires for wear, damage, and proper inflation on a
daily basis. See Vehicle Specifications on page 38.
• Battery: Before using vehicle for the first time, check electrolyte to ensure it is at the proper level
(Figure 26, Page 35). Check battery posts. Wires should be tight and free of corrosion and battery
should be fully charged.
Page 16
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Performance Inspection
• Fuel: Check fuel level. See Fueling Instructions on page 33. Check fuel tank, lines, fuel cap, pump,
fuel filters, and carburetor for fuel leakage on a daily basis.
• Exhaust system: Check for leaks.
PERFORMANCE INSPECTION
After you have familiarized yourself with the vehicle controls and have read and understood the driving
instructions, take the vehicle for a test drive.
Use the following checklist as a guide to inspect the vehicle and check daily for proper operation. Any prob-
lems should be corrected by a Husqvarna distributor/dealer or a trained technician.
• Brakes: Be sure the brakes function properly. When brake pedal is fully pressed under moderate pres-
sure, it should not go more than halfway to the floorboard, and vehicle should come to a smooth,
straight stop. If the brake pedal goes more than halfway to the floorboard, or if the vehicle swerves or
fails to stop, have the brake system checked and adjusted as required. When brake pedal is fully
pressed under heavy pressure, pedal should feel firm and foot pad should be a minimum of 2 inches
(5.1 cm) from floorboard. Brake adjustment must be maintained so the brake pedal cannot be pressed
to the floorboard under any circumstance.
• Park brake: Apply moderate pressure to park brake handle. Tension should increase as the handle is
pulled. When latched, the park brake should lock the wheels and hold the vehicle stationary (on an
incline of 20% or less).
• Reverse buzzer: The reverse buzzer should sound as a warning when the Forward/Reverse handle is
in the REVERSE position.
• Steering: The vehicle should be easy to steer and should not have any play in the steering wheel.
• Accelerator: After starting the engine with the key switch and placing the Forward/Reverse handle in
the FORWARD position, the vehicle should accelerate smoothly to full speed as the accelerator pedal
is pressed. When the pedal is released it should return to the original position and the engine should
idle. Husqvarna vehicles operate at reduced speed in reverse.
a level surface.
• Differential lock cable: With the wheels at rest, pull the differential lock handle toward the rear of the
vehicle (locked position). The differential lock arm at the other end of the cable should move approxi-
mately one-half inch (12.7 mm) downward. When the differential lock handle is placed back into the
unlocked position, the differential lock arm should move approximately one-half inch (12.7 mm)
upward.
• General: Listen for any unusual noises such as squeaks or rattles. Check the vehicle’s ride and perfor-
mance. Have a Husqvarna dealer or a trained technician investigate anything unusual.
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Driving Instructions
DRIVING INSTRUCTIONS
ý WARNING
• Only licensed drivers should be allowed to drive this vehicle.
• Before allowing anyone to drive the vehicle, make sure the driver is familiar with all controls
and operating procedures.
• No one under the age of 16 years should be allowed to drive the vehicle.
• No more than one person per bucket seat at one time, or two persons per bench seat.
• Do not allow riders in the cargo bed.
• For night use, the vehicle must be equipped with headlamps, taillamps, and reflectors.
• The vehicle is not specially equipped for handicapped persons:
- Be sure all passengers are capable of securing themselves in a moving HUV4213 vehicle
before allowing them to ride in one.
- Be sure all persons can properly operate the vehicle prior to allowing them to drive the
vehicle.
• Stop the vehicle before shifting the Forward/Reverse handle. Engine must be at idle before
shifting the Forward/Reverse handle. Failure to do so may result in injury to inattentive
passengers and (or) damage to the vehicle.
• To help avoid being struck, do not stand in front of or behind the vehicle.
• Do not leave children unattended on vehicle.
• Operate the vehicle from the driver seat only.
• To help prevent falls from the vehicle, remain seated and hold on to seat handles at all times.
Driver should keep both hands on the steering wheel when the vehicle is in motion.
• To help prevent the possibility of serious injury, keep entire body inside the vehicle.
• To help prevent overturning the vehicle, drive slowly in turns.
• To help prevent overturning the vehicle, drive slowly straight up and down slopes. Avoid
driving the vehicle on slopes exceeding 20% incline.
• Avoid stopping a loaded vehicle on a hill. If a loaded vehicle must be stopped on a hill, avoid
sudden starts or rolling backwards and stopping suddenly. Failure to heed this warning could
result in overturning the vehicle.
• To help avoid possible injury to inattentive passengers and (or) damage to the vehicle, avoid
sudden starts, sudden stops, and abrupt turns.
• To help avoid the possibility of losing control of or overturning the vehicle, reduce speed for
adverse driving conditions such as wet grass or rough terrain.
• Do not use the vehicle on public roads. It is neither designed nor intended for street use and
should not be licensed for use on public roads.
• The vehicle should be driven in only specified areas by trained drivers.
• Do not drive while under the influence of alcohol, drugs, or medications.
• Use brakes to reduce speed when coasting downhill.
• Never attempt jumps.
No one should drive the vehicle without first being instructed in the proper operation and use of vehicle con-
trols. An experienced operator should accompany each first-time driver on a test drive before allowing the
driver to operate the vehicle alone.
To ensure safe operation of the vehicle, follow exactly and in order, all of the following procedures. Read and
understand all instructions prior to driving the vehicle.
Page 18
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Driving Instructions
STARTING THE VEHICLE
1. Read safety warnings on dash and vehicle loading information located above pedals.
2. Be sure load, if any, is secure.
3. Study and understand controls.
4. Be sure all passengers are seated and holding on to hand holds. Driver should have both hands on the
steering wheel.
5. Make sure wheels are turned in desired direction and nothing is in your path.
6. Make sure the Forward/Reverse handle is in the NEUTRAL position.
7. Press and hold the brake pedal.
8. Turn the key all the way to the START position and hold, activating the choke as necessary, until the
engine is running smoothly. The engine will idle in neutral.
9. Release hand brake.
10. While keeping the brake pedal engaged, select direction of travel by placing shift handle in desired posi-
tion (F = forward or R = reverse). Engine must be at idle before moving shift handle. A buzzer will sound
as a warning when the Forward/Reverse handle is in the REVERSE position.
11. Release the brake pedal completely, and then slowly press the accelerator pedal. As the accelerator
pedal is pressed, the vehicle will begin to move, and speed will increase until full speed is reached. See
following WARNING.
ý WARNING
• Operator must control vehicle speed when going downhill.
• Never shift the vehicle out of the FORWARD position while going downhill. If you do, you will
not be able to shift into the REVERSE position or back into the FORWARD position until
stopped.
• Press the brake pedal as necessary and press the accelerator pedal partially when
descending a hill. With the accelerator pedal partially pressed, the governor will cause the
engine to assist the brakes in controlling downhill speed.
STOPPING THE VEHICLE
To stop the vehicle, release the accelerator pedal and press the brake pedal until the vehicle comes to a com-
plete stop. See following WARNING and CAUTION.
ý WARNING
• Driving through water may affect the brakes. After driving through water, check effectiveness
of the brakes by gently pressing the brake pedal. If the vehicle does not slow down at the
normal rate, continue to press the brake pedal until the brakes dry out and normal
performance returns.
ý CAUTION
• When stopped on a hill, use the brake pedal to hold your position. Do not use the accelerator
pedal to hold position.
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Bed Latch and Prop Rod
PARKING AND LEAVING THE VEHICLE
1. After stopping the vehicle, set hand brake until it locks. Make sure it is fully engaged. This will prevent
the vehicle from rolling.
2. Turn the key switch to the OFF position and place the Forward/Reverse handle in the NEUTRAL position.
Remove the key and turn the fuel shut-off valve to the closed (OFF) position when the vehicle is not in
Figure 10 HUV4213 Bed Latch
Figure 11 HUV4213 Prop Rod
BED LATCH AND PROP ROD
The bed latch (Figure 10) has an automatically engaging prop rod and prop rod track (Figure 11) as standard
features. To lift the bed, pull the bed latch handle toward the rear of the vehicle and lift the bed. The prop rod
will come to rest in one of the notches in the prop rod track. To close the bed, lift the bed so that the prop rod
is no longer supported in one of the track notches. Push the prop rod toward the front of the vehicle to free it
from the track notch and gently lower the bed. DO NOT drop the bed. See following DANGER, WARNING,
and NOTE.
ý DANGER
• Use caution when working under bed. Be sure prop rod is secure. Otherwise the bed will fall,
resulting in severe personal injury or death.
ý WARNING
• For vehicles with cargo beds, remove all cargo before raising the bed or servicing the vehicle.
If the vehicle is equipped with a prop rod, ensure that it is securely engaged. Do not close bed
until all persons are clear of cargo bed area. Keep hands clear of all crush areas. Do not drop
cargo bed; lower gently and keep entire body clear. Failure to heed this warning could result
in severe personal injury or death.
equipped with the electric bed lift accessory.
Page 20
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Shock Absorbers
FRONT SHOCK ABSORBERS
The vehicle arrives from the factory with the front coil-over shocks pre-adjusted for optimum vehicle perfor-
mance. We do not recommend adjusting the shock absorbers unless the vehicle will be equipped with a cab
enclosure. In that event, please refer to the cab installation instructions for the shock absorber adjustment pro-
cedure.
LOADING AND UNLOADING
ý WARNING
• Firmly engage park brake before loading vehicle.
• Do not allow riders in the cargo bed.
• Reduce vehicle load and speed when driving up or down slopes or on uneven terrain.
• Do not exceed rated vehicle capacity. Rated capacity is for level surfaces only.
• Overloading can affect vehicle handling or cause component failure, resulting in loss of
control of vehicle and possible severe personal injury or death.
• Do not load tailgate. The tailgate should be in the upright position and latched securely while
the vehicle is in motion.
• To help avoid shifting vehicle load and possibly overturning the vehicle, avoid sudden starts,
sudden stops and abrupt turns. Make sure cargo is well secured.
• Avoid top-heavy loads. The center of gravity of load should never exceed 15 inches (38 cm)
above the bottom of the cargo bed.
• The cargo’s center of gravity may affect handling, steering, and braking of the vehicle. When
the vehicle is loaded, reduce speed and drive slowly in turns.
• Unload cargo bed before raising vehicle with a lift, hoist, or jack.
• Avoid stopping on a hill when loaded. If you must stop on a hill, avoid sudden starts, or rolling
backwards and stopping suddenly. Failure to heed this warning may cause vehicle to
overturn, possibly resulting in severe personal injury.
• Reduce speed and avoid sudden stops when backing up. Failure to do so may cause the
vehicle to overturn or flip over backwards.
Center and secure cargo as far forward as possible in the cargo bed. Do not overload the vehicle. See the fol-
lowing chart for vehicle capacities.
HUV4213
Maximum payload capacity
800 lb. (363 kg)
(Cargo bed load plus gross trailer weight)
Maximum vehicle capacity
(Cargo load, passengers, plus gross trailer weight)
1200 lb. (545 kg)
Maximum gross vehicle weight
2381 lb. (1080 kg)
(Fully loaded vehicle, including accessories)
Maximum passenger capacity
400 lb. (181 kg)
(Operator and passenger)
Trailer tongue weight
150 lb. force (667 N)
Maximum payload capacity must be reduced accordingly when any option or accessory is installed on the
vehicle. See following NOTE.
NOTE: A standard HUV4213 vehicle with a cab accessory weighing 235 lb. (107 kg) must reduce its max-
imum payload capacity by 235 lb. (107 kg) to 565 lb. (256 kg).
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Towing with the Vehicle
TOWING WITH THE VEHICLE
ý WARNING
• Do not tow a vehicle or trailer on public streets or highways.
• Normal vehicle operating speed should be reduced when towing.
• Extreme caution should be used when towing.
• Do not allow riders in the vehicle or trailer being towed.
• Avoid sudden starts, sudden stops, and tight turns when towing.
• Avoid stopping on a hill when towing. If you must stop on a hill, avoid sudden starts, or rolling
backwards and stopping suddenly. Failure to heed this warning may cause vehicle to
overturn, possibly resulting in severe personal injury.
Towing another HUV4213 vehicle or a trailer can have adverse effects on vehicle handling. Be especially cau-
tious when towing other equipment with an HUV4213 vehicle. See the preceding chart for vehicle capaci-
ties.
Parking the vehicle with a trailer on a hill should be avoided. If you must park on a hill, apply brakes and have
someone chock tires of trailer. Brakes should be released to allow chocks to absorb load of trailer. After tires
have been chocked, engage park brake.
TRANSPORTING ON A TRAILER
ý WARNING
• Do not allow riders in the trailer being towed.
• Avoid sudden starts, sudden stops, and tight turns when towing.
• Avoid stopping on a hill when towing. If you must stop on a hill, avoid sudden starts, or rolling
backwards and stopping suddenly. Failure to heed this warning could cause the vehicle to
overturn, possibly resulting in severe personal injury.
• Reduce normal driving speed when transporting a vehicle on a trailer.
• For use on public roads, the trailer must meet all federal, state, and local requirements such
as taillamps, brake lamps, etc.
• Never tow a Husqvarna vehicle behind a passenger vehicle or truck on a public road unless it
is on an approved trailer.
• The vehicle to be transported should be tied securely to the trailer, with the Forward/Reverse
handle in the NEUTRAL position, the key switch in the OFF position, and the park brake firmly
engaged.
• Because of the added length of the trailer, use caution when making turns.
• Do not transport the vehicle on a trailer with a load in the vehicle cargo bed.
• Remove the vehicle windshield and secure the seats before transporting on a trailer.
If the vehicle must be transported over long distances or on public highways, it should be transported on an
approved trailer that has an approved load rating of 2000 lb. (908 kg) per vehicle being transported.
NOTE: A two-car trailer should be rated at 2 x 2000 lb. = 4000 lb. (2 x 908 kg = 1816 kg).
Page 22
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage
STORAGE
ý DANGER
• Do not attempt to drain gasoline when the engine is hot or while it is running.
• Be sure to clean up any spilled gasoline before operating the vehicle.
• Store gasoline in an approved gasoline container only. Store in a well-ventilated area away
from sparks, open flames, heaters, or heat sources.
• Keep gasoline out of the reach of children.
• Do not siphon gasoline from the vehicle.
ý WARNING
• Turn the key switch to the OFF position, remove the key, and leave the Forward/Reverse
handle in the NEUTRAL position during storage. This is to prevent unintentionally starting the
vehicle or a fire hazard.
• Do not attempt to charge frozen batteries or batteries with bulged cases. Discard the battery.
Frozen batteries can explode.
ý CAUTION
• Batteries in a low state of charge will freeze at low temperatures.
PREPARING THE VEHICLE FOR EXTENDED STORAGE
1. Unload the vehicle so that tires are supporting only the weight of the vehicle.
2. Store vehicle in a cool, dry place. This will minimize battery self-discharge. If the battery appears to be
weak, have it charged by a trained technician. Use an automotive-type 12-volt battery charger rated at
10 amps or less. Check electrolyte level after charging and add distilled water if necessary.
3. Make sure the key switch is in the OFF position and the Forward/Reverse handle is in the NEUTRAL
position. Chock the wheels.
4.1. Tilt the bed and ensure that the prop rod is properly engaged.
5. Lift the front passenger side seat.
6. Drain carburetor and seal the fuel tank.
6.1. Turn the fuel shut-off valve to the closed (OFF) position (Figure 13) and run the engine until fuel
remaining in the carburetor and fuel line is depleted and the engine stalls.
6.2. Loosen, but do not remove, the carburetor drain screw and drain fuel remaining in bowl into a small,
clean container, then pour the fuel from the container into vehicle fuel tank. Tighten the carburetor
drain screw.
6.3. Fill fuel tank to about 1 inch (2.5 cm) from top of fuel tank and, following manufacturer’s directions,
add a commercially available fuel stabilizer (such as Sta-Bil®).
6.4. Disconnect fuel vent line from fuel tank vent nipple.
6.5. Plug the fuel tank vent nipple so that it is air tight. We recommend using a slip-on vinyl cap.
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage
CLOSED (OFF) POSITION
(SELECTOR IS ALIGNED
WITH OFF MARKINGS ON THE SIDES OF VALVE)
OFF
OFF
VIEWED FROM SELECTOR
SIDE OF VALVE
Figure 12 Fuel Shut-off Valve – Closed Position
7. Disconnect the battery cables, negative (–) cable first. See WARNING “To avoid unintentionally start-
8. Batteries should be clean and free of corrosion. Wash tops and terminals of batteries with a solution of
baking soda and water (1 cup (237 mL) baking soda per 1 gallon (3.8 L) of water). Rinse solution off bat-
teries. Do not allow this solution to enter the batteries. Be sure terminals are tight. Let the terminals dry
and then coat them with Battery Terminal Protector Spray (P/N 603 00 00-03).
9. To protect the engine, remove spark plug and pour 1/2 ounce (14.2 mL) of SAE 10 weight oil into the
engine through the spark plug hole. Rotate engine crankshaft by hand several times and then install the
spark plug.
10. Lower the passenger side seat.
14. Thoroughly clean front body, rear body, seats, cargo bed, engine compartment, and underside of vehicle.
15. Do not engage the park brake. Chock the wheels to prevent the vehicle from rolling.
RETURNING THE STORED VEHICLE TO SERVICE
1. Make sure the key switch is in the OFF position and the Forward/Reverse handle is in the NEUTRAL
position. Chock the wheels.
3. Tilt the bed and ensure that the prop rod is properly engaged. See WARNING “For vehicles with cargo
4. Lift the passenger seat.
5.1. Remove plug from fuel tank vent.
5.2. Connect vent tube to fuel tank vent.
Page 24
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
6. Connect battery cables, positive (+) cable first, and tighten terminals to 12 ft-lb (16 N·m). Coat terminals
with Battery Terminal Protector Spray (P/N 603 00 00-03).
7. Completely open the fuel shut-off valve (Figure 13). Make sure the valve is fully open. A partially closed
fuel shut-off valve combined with the use of the choke can result in a fouled spark plug and engine failure
8. Place the Forward/Reverse handle in the NEUTRAL position. Crank the engine until fuel is pumped into
the carburetor and fuel lines and the engine starts. Turn the engine off. See following NOTE.
NOTE: Due to the oil added to the engine in preparation for storage, engine may smoke excessively for a
short time when it is run for the first time after storage.
10. Lower the passenger side seat.
FULL OPEN (ON)
POSITION
PARTIALLY CLOSED
POSITION
VIEWED FROM SELECTOR
SIDE OF VALVE
VIEWED FROM SELECTOR
SIDE OF VALVE
Figure 13 Fuel Shut-off Valve – Open Position
Figure 14 Fuel Valve – Partially Closed Position
MAINTENANCE
To ensure trouble-free vehicle performance, follow an established preventive maintenance program. Regular
and consistent maintenance can prevent vehicle downtime and expensive repairs. Use the Pre-Operation
and Daily Safety Checklist on page 16, Performance Inspection on page 17, and the following Periodic Ser-
vice Schedule and Periodic Lubrication Schedule to keep the vehicle in proper working condition.
Any vehicle not functioning correctly should not be used until it is properly repaired. This will prevent further
damage to the vehicle and avoid the possibility of injury due to unsafe conditions.
Contact your local Husqvarna dealer for repairs and semiannual and annual periodic service. See following
WARNING.
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Periodic Service Schedule
ý WARNING
• Only trained technicians should service or repair the vehicle. Anyone doing even simple
repairs or service should have knowledge and experience in electrical and mechanical repair.
The appropriate instructions must be used when performing maintenance, service, or
accessory installation.
• If any problems are found during scheduled inspection or service, do not operate vehicle until
repairs are made. Failure to make necessary repairs could result in fire, property damage,
severe personal injury, or death.
• Do not wear loose clothing or jewelry, such as rings, watches, chains, etc., when servicing
vehicle.
• Turn the key switch to the OFF position, remove the key, place the Forward/Reverse handle in
the NEUTRAL position and chock the wheels prior to servicing.
• Moving parts: Do not attempt to service vehicle while engine is running.
• Hot! Do not attempt to service hot engine or exhaust system. Failure to heed this warning
could result in severe burns.
• For vehicles with cargo beds, remove all cargo before raising the bed or servicing the vehicle.
If the vehicle is equipped with a prop rod, ensure that it is securely engaged. Do not close bed
until all persons are clear of cargo bed area. Keep hands clear of all crush areas. Do not drop
cargo bed; lower gently and keep entire body clear. Failure to heed this warning could result
in severe personal injury or death.
• Do not work on vehicle powertrain or under cargo bed when it is loaded.
• To help avoid unintentionally starting the vehicle:
- Disconnect the spark plug wire from the spark plug.
• If wires are removed or replaced make sure wiring and wire harness are properly routed and
secured. Failure to properly route and secure wiring could result in vehicle malfunction,
property damage, personal injury, or death.
• Lift only one end of the vehicle at a time. Use a suitable lifting device (chain hoist or hydraulic
floor jack) with 1000 lb. (454 kg) minimum lifting capacity. Do not use lifting device to hold
vehicle in raised position. Use approved jack stands of proper weight capacity to support the
vehicle and chock the wheels that remain on the floor. When not performing a test or service
procedure that requires movement of the wheels, lock the brakes.
PERIODIC SERVICE SCHEDULE
ý WARNING
• Service, repairs, and adjustments must be made per instructions in the appropriate
maintenance and service manual.
NOTE: If the vehicle is constantly subjected to heavy use or severe operating conditions, the preventive
maintenance procedures should be performed more often than recommended in the Periodic Ser-
vice and Lubrication Schedule.
Both the Periodic Service Schedule and the Periodic Lubrication Schedule must be followed to
keep vehicle in optimum operating condition.
Page 26
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Periodic Service Schedule
PERIODIC SERVICE SCHEDULE
REGULAR INTERVAL
SERVICE
Monthly service by owner
or trained technician
Check engine oil level; change if
necessary. See Periodic Lubrication
Engine
Check engine cooling air intake; visually
inspect unshrouded area around engine
exhaust for grass and debris and clean if
necessary.
Check air pressure and adjust if
necessary. See Vehicle Specifications
Tires
Wash engine compartment and underside
of vehicle. Do not wash engine when hot.
General vehicle
Battery
Semiannual service by trained
technician only
Clean terminals and wash dirt from
casing; check electrolyte level. Add
(or every 50 hours of operation,
whichever comes first)
Check and adjust if necessary. See
Section 7 – Steering and Front
Suspension in the appropriate
maintenance and service manual.
Front wheel alignment and toe-in
Electrical wiring and connections
Check for tightness and damage.
Inspect master cylinder, wheel cylinders,
brake lines, and hoses for damage or
leakage.
Check park brake cables for damage;
replace if necessary.
Brake system
Check brake shoes and drums; replace if
necessary. See Section 6 – Park Brake
System and Wheel Brake Assemblies
in the appropriate maintenance and
service manual.
Annual service by
Check for leaks around gaskets, fill plugs,
etc.
trained technician only
(or every 100 hours of operation,
whichever comes first)
Engine
Inspect, clean and gap spark plug; replace
if necessary.
Check air filter element; clean or replace if
necessary.
Engine air intake system
Check clamps for tightness; check hose
for cracks.
Check for loose hardware and tighten if
necessary.
General vehicle
Fuel filters
Two year service by
Replace. Dispose of used filters properly.
trained technician only
(or every 200 hours of operation,
whichever comes first)
ý WARNING
• If any problems are found during scheduled inspection or service, do not operate vehicle until
repairs are made. Failure to make necessary repairs could result in fire, property damage,
severe personal injury, or death.
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Periodic Lubrication Schedule
PERIODIC LUBRICATION SCHEDULE
PERIODIC LUBRICATION SCHEDULE
LUBRICATION
POINTS
REGULAR INTERVAL
SERVICE
RECOMMENDED LUBRICANT
Semiannually by owner
or trained technician (or
every 50 hours of
operation, whichever
comes first)
Brake pedal shaft bearings
Dry Moly Lube (P/N 603 00 00-01)
Dry Moly Lube (P/N 603 00 00-01)
1
2
Accelerator push rod pivots,
mounts, and shifter cable pivots
Front suspension (2 fittings)
Check/add brake fluid
Chassis Lube (EP NLGI Grade 2)
Use only DOT 5 (silicone) brake fluid
3
4
Annually by trained
technician only
(or every 100 hours of
operation, whichever
comes first)
29 oz. (0.85 liters) 80-90 Wt. API Class
GL-3 or 80-90 Wt. AGMA Class 5 EP
gear lubricant
Check/fill transaxle to plug level
5
6
Inspect front wheel bearings
(Repack as necessary)
Chassis Lube (EP NLGI Grade 2)
First change 100 hours –
additional change
every 200 hours of
operation or annually,
whichever comes first.
Change engine oil and oil filter
7
FLOORBOARD
6
3
2
1
2
2
5
2
1
2
4
7
3
6
Figure 15 HUV4213 Lubrication Points
Page 28
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Master Cylinder
MASTER CYLINDER
Full
Level
N R
E
A I
T
U I D
Y
N I N
G
R
U S
E
A
W
MAX
MIN
Safe Level
M
A
X
Low
Level
M
IN
Figure 16 Brake Fluid Reservoir
The master cylinder is located under the passenger bucket seat toward the center of the vehicle (Figure 16).
Raise or remove the seat to check the brake fluid level.
When checking the brake fluid, also inspect the following:
• The presence of brake fluid on the exterior surface of the master cylinder indicates a leak.
• The vent holes in the reservoir cover should be clean and open.
• The reservoir diaphragm should not have holes or other damage.
BRAKE FLUID
Brake fluid level should be within 1/4-inch (6 mm) from top of reservoir (Figure 16). Also, brake fluid should
be clean with no residue in bottom of reservoir or other evidence of contamination.
ý CAUTION
• Use only DOT 5 (silicone) brake fluid. Use of any other type brake fluid is not recommended.
ENGINE OIL
Even though the low oil warning lamp on the dash should illuminate if oil becomes low, the engine oil level
should be checked monthly. The vehicle should be on a level surface when checking oil. Do not overfill with
oil.
ENGINE OIL LEVEL CHECK
1. Remove the oil level dipstick from the oil filler tube and wipe oil from stick. See Figure 17. See following
CAUTION.
ý CAUTION
• Do not remove dipstick while engine is running.
2. Check oil by fully inserting the dipstick into the oil filler tube and immediately removing it.
3. If the oil level is at or below the low level mark on the dipstick gauge, add oil until the level is between
low and full levels (safe level).
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine Oil
2
3
full
level
1
safe
level
low
Lleevveell
Oil fill tube is located behind and under passenger seat.
Figure 17 Engine Oil Level Check – HUV4213
ENGINE OIL AND FILTER CHANGE
Engine oil and oil filter should be changed after the first 100 hours of operation. After that, they should be
changed every 200 hours of operation or annually, whichever comes first.
1. Turn the key switch to the OFF position then remove the key. Place the Forward/Reverse handle in the
NEUTRAL position. Chock the front wheels.
3. Tilt the bed and ensure that the prop rod is properly engaged.
4. Disconnect the battery cables, negative (–) cable first. See WARNING “To avoid unintentionally start-
6. Use a 14 mm socket or wrench to remove the drain plug, turning it counterclockwise, and allow the
engine oil to drain into the pan.
ý WARNING
• Do not attempt to change engine oil when the engine is hot or even warm. Engine oil can
cause skin burns.
• Wear safety glasses or approved eye protection when servicing the vehicle. Wear rubber
gloves when handling oil drain plug, oil filter, and oil drain pan.
7. Clean the oil drain plug threads with solvent to remove oil and oil residue. Make sure that the compres-
sion washer remains on the drain plug.
8. Use a 14 mm socket or wrench and replace the front oil drain plug, turning it clockwise, and tighten to
18 ft-lb (24.4 N·m).
Page 30
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine Oil
OIL FILTER
DRAIN PAN
DRAIN PLUG
Figure 18 Engine Oil Drain Plug and Pan
9. Place a floor jack under the rear receiver hitch where the hitch and body frame are fastened. Lift the vehi-
cle body slightly, allowing the front of the engine to tilt slightly downward. This will allow the oil filter more
11. Remove the engine oil filter, turning it counterclockwise, allowing the residual oil in the filter port and filter
USED OIL FILTER
Compress
down.
OIL DRIP GUARD
DRAIN PAN
SNUBBER
BRACKET
SNUBBER
Figure 19 Compress Snubber Downward
Figure 20 Remove Engine Oil Filter
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine Oil
Figure 21 Coat Rubber Seal
Figure 22 Add Engine Oil
NOTE: An oil drip guard can be used to prevent excess oil from dripping into the engine base plate. Use
an empty quart (1 liter) container and cut the bottom off at an angle, then slide the open area of the
container up and under the oil filter prior to removal. Position the port of the plastic container so oil
board, thin metal, or plastic under the oil filter, forming a channel to direct the filter port oil into the
drain pan.
Dispose of used oil according to the environmental laws and regulations for your area.
12. Use a clean rag and wipe the oil filter mounting bracket surface clean where the oil filter gasket seats.
13. To help seal the new oil filter to the oil filter mounting bracket, apply a light coat of white lithium NLGI
Number 2 grease (Dow Corning® BR2-Plus or equivalent) or new engine oil to the rubber seal around
the outside surface of the filter before attaching it to the oil filter port (Figure 21). Install the new oil filter
(P/N 603 00 00-06) onto the engine oil filter port. See following NOTE.
NOTE: Use only Husqvarna oil filters (P/N 603 00 00-06) designed for this engine.
14. Tighten the oil filter by hand 2/3 turn after gasket contact. Do not use a band wrench or channel lock plier
to tighten.
15. Lower the vehicle and remove the floor jack from under the rear of the vehicle.
16. Remove the dipstick and add engine oil into the dipstick port. Use a funnel or pour spout to direct the oil
into the dipstick port (Figure 22). With filter change, the engine requires 38 ounces (1.12 liters) of oil per
change. Refer to oil viscosity guidelines for selection of oil grade (Figure 23). Replace the dipstick.
17. Connect the battery cables, positive (+) cable first, and tighten terminals to 20 ft-lb (27.1 N·m). Coat ter-
minals with Battery Terminal Protector Spray (P/N 603 00 00-03).
19. With the Forward/Reverse handle in the NEUTRAL position, start and run the engine for a few minutes.
Observe both the drain plug and the oil filter from under the vehicle and watch for oil leaks. If leaks
appear, begin with step 1 and repeat the appropriate step for either or both items to correct the problem.
20. Remove the dipstick and check the engine oil as a final step. Replace the dipstick.
Page 32
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Fueling Instructions
OIL VISCOSITY
-20° C -10° C 0° C 10° C 20° C 30° C 40° C
SAE 40
SAE 30
SAE 10W-30/SAE 10W-40
SAE 5W-20
-4° F 14° F 32° F 50° F 68° F 86° F 104° F
Figure 23 Oil Viscosity Chart
NOTE: Using multi-grade oils (5W-20, 10W-30, and 10W-40) will increase oil consumption. Check oil level
more frequently when using them.
FUELING INSTRUCTIONS
ý DANGER
• Turn the key switch to the OFF position before fueling.
• Never pour gasoline into the fuel tank when the engine is hot or while it is running.
• To avoid electric arc caused by static electricity, the fuel storage/pumping device must be
grounded. If the pump is not grounded, the vehicle must be grounded to the pump before and
during the fueling operation.
• If the vehicle has an all-weather enclosure installed, be sure the fuel tank is properly vented as
• To avoid the possibility of fire, clean up any spilled gasoline before operating the vehicle.
ý CAUTION
• To allow for expansion, do not fill higher than one inch (2.54 cm) from the top of the fuel tank.
Avoid spilling fuel.
1. Remove the passenger seat.
2. Remove fuel cap and fill tank with fresh unleaded gasoline only. See preceding DANGER and CAU-
TION.
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery
NOTE: Whenever possible, avoid using oxygenated fuels and fuels that are blended with alcohol. Vehicles
to be stored for extended periods should be prepared for storage as instructed. See Preparing the
3. Replace fuel cap on the tank. Ensure cap is tightened securely.
4. Clean any spilled fuel from the tank top and around the tank area.
5. Replace passenger seat.
ý WARNING
• Make sure seat hinges and latch are securely engaged before operating vehicle.
FUEL
SHUT-OFF
VALVE
VENT
TO CARBURETOR
FUEL
TANK
VENT TUBE
Figure 24 Fuel Tank – HUV4213
BATTERY
ý DANGER
• Battery – Explosive gases! Do not smoke. Keep sparks and flames away from the vehicle and
service area. Ventilate when charging or operating vehicle in an enclosed area. Wear a full
face shield and rubber gloves when working on or near batteries.
• Tools, wires, and metal objects can cause sparks when shorted across a battery.
• Follow all instructions carefully when working with batteries.
• Charge battery in a well-ventilated area only.
• Battery – Poison! Contains acid! Causes severe burns. Avoid contact with skin, eyes, or
clothing. Antidotes:
- External: Flush with water. Call a physician immediately.
- Internal: Drink large quantities of milk or water followed with milk of magnesia or vegetable
oil. Call a physician immediately.
- Eyes: Flush with water for 15 minutes. Call a physician immediately.
Page 34
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery
ý WARNING
• Do not jump-start a dead battery using another battery and jumper cables.
The battery in a Husqvarna vehicle is a 12-volt, low-maintenance battery that requires infrequent checks
(Figure 25). Electrolyte level should be checked semiannually.
1. Turn the key switch to the OFF position and remove the key. Place the Forward/Reverse handle in the
NEUTRAL position. Chock the wheels.
3. Tilt the bed and ensure that the prop rod is properly engaged.
4. Disconnect the battery cables, negative (–) cable first. See WARNING “To avoid unintentionally start-
5. Use a flat blade screwdriver, and carefully remove the battery cell caps from the battery (Figure 25). See
following WARNING.
ý WARNING
• Wear safety glasses or approved eye protection when servicing the vehicle. Wear a full face
shield and rubber gloves when working on or near batteries.
6. Carefully check the electrolyte level and add distilled water if necessary. Do not fill above designated fill
line. Replace battery cell caps.
BATTERY
CAP
LEVEL
INDICATOR
PLATES
ELECTROLYTE
LEVEL AT LEAST
1/2-INCH (13 MM)
ABOVE
PLATES OR
TO LEVEL
INDICATOR
Figure 25 Battery
Figure 26 Battery Electrolyte Level
7. Clean both battery terminals with a solution of baking soda and water (1 cup (237 mL) baking soda per
1 gallon (3.8 L) of water). Rinse thoroughly. Do not allow this solution to enter the battery. Tighten battery
terminals to 12 ft-lb (16 N·m). Let the terminals dry and then spray them with Battery Terminal Protector
Spray (P/N 603 00 00-03). See following WARNING.
ý WARNING
• If battery wire terminals are damaged or corroded, replace or clean them as necessary. Failure
to do so may cause them to overheat during operation and could result in fire, property
damage, or personal injury.
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the Vehicle
Be sure battery hold-down clamp is properly tightened. Tighten to 12 ft-lb (16 N·m). A loose clamp may allow
the battery to become damaged from vibration or jarring.
If battery appears weak, have it charged by a trained technician. The battery should never be left discharged
any longer than absolutely necessary (do not leave discharged overnight).
CLEANING THE VEHICLE
Each vehicle is equipped with an ABS/DR acrylic front body and an all-aluminum rear body. The HUV4213
has a powder-coated steel cargo bed. Use commercial automotive cleaning solutions with a sponge or soft
cloth for normal cleaning. A garden hose at normal residential water pressure is adequate. To remove oxida-
tion or discoloration from aluminum, use a commercially available aluminum cleaner paste and fine grade
(No. 00) steel wool.
Husqvarna does not recommend any type of pressure washing or steam cleaning. Such a process will expose
electrical components to moisture. Moisture entering electrical components can result in water damage and
subsequent component failure.
Use non-abrasive wax products. Battery acid, fertilizers, tars, asphalt, creosote, paint, or chewing gum should
be removed immediately to prevent possible stains.
The front body is made of an ABS/DR acrylic cap material similar to the material used to manufacture hot tubs
and shower/tub units. Cleaning and repair techniques for the front body are the same as those used on con-
ventional acrylic sheet. Use cleaning and polishing products available at any hardware store where ABS/DR
acrylic (hot tubs and shower/tub units) are sold.
The seats of the vehicle will last longer with proper cleaning. Use a solution of 10% liquid soap and warm
water applied with a soft cloth. For imbedded dirt, a soft bristle brush may be used. For heavy soiling, difficult
stains, or scratches, blemishes, or other body damage, see the appropriate maintenance and service manual.
See following NOTE.
NOTE: Dispose of waste water properly.
ACCESSORIES
There is a complete line of accessory equipment available from Husqvarna and our dealers/distributors. You
can obtain the name and phone number of your closest Husqvarna contact by visiting our web site at
Care should be taken that these accessories are properly installed by trained technicians, and that they are
used in the manner for which they were designed. See following WARNING.
ý WARNING
• Custom cab assemblies, canopy tops, weatherproof enclosures, and windshields will not
protect occupants from flying objects.
• If the vehicle is equipped with an electric powered bed lift, remove the bed before servicing
the bed lift system.
Page 36
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Subsequent Owner Registration
ELECTRIC WINCH ACCESSORY
If your vehicle is equipped with an electric winch, read and follow all manufacturer safety warnings and
instructions in the winch operator manual, as well as the following WARNING and CAUTION statements.
Make sure a winch warning decal is affixed to the vehicle on the seat support panel next to the receptacle for
The winch kit available from Husqvarna includes a remote operation switch, which enables the operator to
move away from the vehicle and cable. See following WARNING and CAUTION.
ý WARNING
• Before beginning a winch operation:
- Turn the key switch to the OFF position, put Forward/Reverse handle in the NEUTRAL
position, and engage the park brake.
- Do not use winch while persons are seated on the vehicle.
• Stand to the side and away from the vehicle to operate winch.
CAUTION
• Use of the winch for an extended period of time could discharge the battery. Keep winch
operations as short as possible, and drive the vehicle for several minutes after the winch
operation to recharge the battery.
SUBSEQUENT OWNER REGISTRATION
In the event a vehicle is bought as a used vehicle, we strongly urge the new owner to register the vehicle with
Husqvarna. This will enable us to contact you if the need arises. Please send your name, address, and serial
number of the vehicle to Husqvarna, 7349 Statesville Rd., Charlotte, NC 28269, Attention: Vehicle Registra-
tion.
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Vehicle Specifications
VEHICLE SPECIFICATIONS
HUV4213-GXP
HUV4213-G
SPECIFICATIONS
POWER SOURCE
Engine: 4-cycle OHV, 400 cc, 13.0 maximum HP @3600 rpm (per SAE J 1940/1349), single-
cylinder, air-cooled, with pressure lubrication system
•
Fuel system: Side-draft carburetor with float bowl, fixed jets, fuel filters, and impulse fuel pump
Governor: Automatic ground-speed sensing, internally geared in unitized transaxle
Ignition: Transistor electronic ignition with electronic RPM limiter
•
•
•
Unitized transaxle, MC012C-BS00: Fully synchronized forward and reverse with neutral
(14.9:1 forward, 20.5:1 reverse) and differential lock feature
•
Electrical system: 12-volt, 500 cca at 0 °F (-17.8 °C), 650 at 32 °F (0 °C). 105-minute reserve
•
•
capacity and 35-amp charging capacity
Torque converter: Automatic, variable-speed, dry type
STEERING/SUSPENSION/BRAKES
Steering: Self-adjusting rack and pinion, Ackerman
•
•
Suspension:
Front: Independent A-arms with coil-over shocks
Rear: Semi-independent suspension with multi-leaf springs and dual hydraulic shocks
Brakes: Hydraulic brake system – self-adjusting drum brakes on each wheel with separate
hand-operated park brake
•
BODY/CHASSIS
Frame/Chassis: Twin I-Beam welded aluminum
Side and rear body: All aluminum
Cargo bed: Powder-coated steel
Front body: ABS/DR acrylic cap
Tires: 23 x 10.50 – 12 tubeless, 4-ply rated load range, front and rear
DIMENSIONS/WEIGHT
•
•
•
•
•
Overall length (box bed configuration)
Overall width
123.4 in. (313.4 cm)
54 in. (137 cm)
75 in. (187.5 cm)
80 in. (203 cm)
Overall height (at lamp bar)
Wheelbase
Ground clearance:
under differential
under foot platform
6.6 in. (17 cm)
11.4 in. (29 cm)
Front wheel tread
Rear wheel tread
43 in. (109 cm)
44.5 in. (111 cm)
Weight (dry):
with all-terrain tread
with turf tread
1106 lb. (493.4 kg)
1066 lb. (477.2 kg)
1063.5 lb. (482.4 kg)
1027.8 lb. (466.2 kg)
Forward speed
17-19 mph (27-31 km/h)
Governed RPM: FE400 Engine
Curb clearance circle (diameter)
Turning radius (per SAE J 695)
Intersecting aisle clearance
Floorboard height
3850 (±30) RPM
24 ft. 1 in. (734 cm)
139.6 in. (355 cm)
112.2 in (285 cm)
17 in. (43 cm)
Specifications continued on next page...
Page 38
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Vehicle Specifications
HUV4213-GXP
HUV4213-G
SPECIFICATIONS
DIMENSIONS/WEIGHT, Continued
Seat height
35 in. (89 cm)
Load bed height
31.1 in. (79 cm)
48.0 x 49.8 x 10.9 in.
(121.4 x 126.4 x 27.6 cm)
(15.3 cubic feet)
Load bed size (box bed inside dimensions)
Load bed size (flat bed dimensions)
46.9 x 48.3 in.
(119 x 123 cm)
Vehicle rated capacity (level surface only)
Bed load capacity (level surface only)
Standard seating capacity
LIQUID CAPACITIES
1200 lb. (544 kg)
800 lb. (363 kg)
2
Engine crankcase without filter
Engine crankcase with filter
Unitized transaxle, MC012C-BS00
Master cylinder
32 oz. (0.95 liters)
38 oz. (1.12 liters)
29 oz. (0.85 liters)
8 oz. (240 ml)
Fuel tank
7 gallons (26.5 liters)
TIRE PRESSURE
Front: 7-11 psi
(0.48-0.76 Bars)
Rear: 14-18 psi
(0.97-1.24 Bars)
All-terrain tread (standard)
Turf tread (optional)
Front: 12-16 psi
(0.83-1.10 Bars)
Rear: 16-20 psi
(1.10-1.38 Bars)
Front: 14-16 psi
(0.97-1.10 Bars)
Rear: 18-20 psi
(1.24-1.38 Bars)
Traks Max II tread (optional)
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
®
HUSQVARNA LIMITED TWO YEAR WARRANTY FOR 2007
TRANSPORTATION AND UTILITY VEHICLES
1. WARRANTY:
HUSQVARNA, INC., ("HUSQVARNA") hereby warrants to the Original Retail Purchaser that its new 2007 Model
Transportation and Utility Vehicles purchased from HUSQVARNA or an authorized dealer shall be free from defects in
material and workmanship under normal use and service as a transportation or utility vehicle for the periods stated below,
subject to the provisions, limitations and exclusions contained in this limited warranty.
LIMITED TWO YEAR / 2000 HOUR WARRANTY: The engine assembly, unitized transaxle assembly (gasoline vehicle),
motor, transaxle assembly (electric vehicle), main frame assembly, box bed hydraulic dump kit, Custom Cab assembly and
doors, and Driving Range Protective Enclosure are warranted with respect to parts and labor against defects in material and
workmanship for a period of two years or 2000 hours of operation, whichever first occurs, from the date of purchase.
LIMITED ONE YEAR / 1000 HOUR WARRANTY: All remaining components of the vehicle not specified otherwise, the
Portable Refreshment Center, and all other original equipment options and accessories supplied by HUSQVARNA are
warranted with respect to parts and labor against defects in material and workmanship for a period of one year or 1000
hours of operation, whichever first occurs, from the date of purchase.
This limited warranty covers material, workmanship and repair labor cost as to those items specifically listed above for the
periods specified. Such repair labor shall be performed only by HUSQVARNA, its authorized dealers, or a service agency
approved by HUSQVARNA.
IF THE WARRANTY REGISTRATION FORM IS NOT COMPLETED AND RETURNED TO HUSQVARNA AT THE TIME
OF THE ORIGINAL RETAIL SALE, PURCHASER MUST PROVIDE PROOF OF DATE OF PURCHASE WITH ANY
WARRANTY CLAIM.
2. EXCLUSIONS:
Excluded from any HUSQVARNA warranty are all fuses, filters, decals (except safety decals), spark plugs, light bulbs,
lubricants, trim pieces, seats, routine wear items such as the charger plug and receptacle, brake shoes, belts, brushes,
bushings, engine mounts, mats and pads, maintenance adjustments, cosmetic deterioration, and items which deteriorate or
fail due to exposure or ordinary wear and tear. Batteries, battery charger, onboard computer, and solid-state speed
controller are covered under separate HUSQVARNA warranties. Also excluded from any HUSQVARNA warranty is
damage to a vehicle or component resulting from a cause other than a defect including unreasonable or unintended strain
or use, improper installation of accessories, installation of parts or accessories that are not original equipment, overloading,
accident, alteration, abuse or neglect.
Transportation expenses for warranty services are also excluded from this warranty.
3. VOIDING OF WARRANTY:
THIS AND ANY OTHER WARRANTY SHALL BE VOID IF THE VEHICLE IS ABUSED OR USED IN AN UNINTENDED
MANNER OR SHOWS INDICATIONS THAT IT HAS BEEN ALTERED IN ANY WAY, INCLUDING, BUT NOT LIMITED TO,
MODIFICATION OF THE SPEED GOVERNOR, BRAKING SYSTEM, STEERING, TRANSAXLE, OR OTHER
OPERATING SYSTEMS OF THE VEHICLE TO CAUSE IT TO PERFORM OUTSIDE HUSQVARNA SPECIFICATIONS.
THE WARRANTY IS LIKEWISE VOID IF THE VEHICLE INVOLVED SHOWS INDICATIONS THAT REASONABLE OR
NECESSARY MAINTENANCE AS OUTLINED IN THE OWNER’S MANUAL AND MAINTENANCE AND SERVICE
MANUAL WAS NOT PERFORMED AT THE TIME AND IN THE MANNER SPECIFIED IN SUCH MANUALS.
4. SOLE REMEDY:
HUSQVARNA’s liability under this limited warranty, or in any action whether based upon warranty, contract, negligence,
strict product liability or otherwise, shall be the repair or replacement, at HUSQVARNA’s option, of the vehicle or component
thereof that HUSQVARNA deems to be defective. Replacement shall mean furnishing, during the applicable limited
warranty period, a new vehicle or factory-reconditioned vehicle or component thereof that is identical or reasonably
equivalent to the warranted product or component at no cost to the purchaser. Repair shall mean remedying a defect in the
vehicle or component thereof at no cost to the purchaser during the applicable limited warranty period. If HUSQVARNA
elects to repair the vehicle, it may provide factory-reconditioned parts or components. All parts and components replaced
under warranty shall become the property of HUSQVARNA.
5. HOW TO MAKE A WARRANTY CLAIM:
To make a warranty claim under this limited warranty, you must present the vehicle or defective component to an authorized
HUSQVARNA dealer.
Page 40
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6. DISCLAIMER:
THIS LIMITED WARRANTY IS EXCLUSIVE. HUSQVARNA MAKES NO OTHER WARRANTY OF ANY KIND,
EXPRESSED OR IMPLIED. ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE WHICH EXCEED THE OBLIGATIONS OR TIME LIMITS STATED IN THIS WARRANTY ARE HEREBY
DISCLAIMED BY HUSQVARNA AND EXCLUDED FROM THIS WARRANTY. THE PURCHASER AND HUSQVARNA
EXPRESSLY AGREE THAT THE REMEDY OF THE REPLACEMENT OR REPAIR OF THE DEFECTIVE VEHICLE OR
COMPONENT THEREOF IS THE SOLE REMEDY OF THE PURCHASER. HUSQVARNA MAKES NO OTHER
REPRESENTATION OR WARRANTY OF ANY KIND, AND NO REPRESENTATIVE, EMPLOYEE, OR DEALER OF
HUSQVARNA HAS THE AUTHORITY TO MAKE OR IMPLY ANY REPRESENTATION, PROMISE OR AGREEMENT,
WHICH IN ANY WAY VARIES THE TERMS OF THIS WARRANTY.
7. NO CONSEQUENTIAL DAMAGES:
IN NO EVENT SHALL HUSQVARNA BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING, BUT NOT LIMITED TO, LOSS RELATED TO PROPERTY OTHER THAN THE VEHICLE, LOSS OF USE,
LOSS OF TIME, INCONVENIENCE, OR ANY OTHER ECONOMIC LOSS.
Some states allow neither limitation on the duration of an implied warranty nor exclusions or limitation of incidental or
consequential damages. Therefore, the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
8. INFORMATION:
For further information contact WARRANTY SERVICES, HUSQVARNA FOREST & GARDEN,
7349 STATESVILLE ROAD, CHARLOTTE, NC 28269 OR CALL 1-800-448-7543.
9. WARNING:
Any modification or alteration of any vehicle beyond factory specifications, including those that affect the weight distribution,
stability, or speed of the vehicle, can cause serious personal injury or death.
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 41
Download from Www.Somanuals.com. All Manuals Search And Download.
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
Your new Husqvarna, Inc. ("HUSQVARNA") vehicle engine complies with both the U.S. EPA and State of California emission regulations.
YOUR WARRANTY RIGHTS AND OBLIGATIONS:
The California Air Resources Board ("CARB") and HUSQVARNA are pleased to explain the emission control system warranty on your 2007 vehicle engine. In California, new small off-
road engines (SORE) must be designed, built and equipped to meet the State's stringent anti-smog standards. HUSQVARNA must warrant the emission control system on the vehicle
engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your small off-road engine.
Your emission control system may include parts such as the carburetor or fuel-injection system, the ignition system, and catalytic converter. Also included may be hoses, belts,
connectors and other emission-related assemblies.
Where a warrantable condition exists, HUSQVARNA will repair your vehicle engine at no cost to you including diagnosis, parts and labor.
MANUFACTURER'S WARRANTY COVERAGE:
This emission control system is warranted for two years. If any emission-related part on your equipment is defective, the part will be repaired or replaced by HUSQVARNA.
OWNER'S WARRANTY RESPONSIBILITIES:
- As the vehicle engine owner, you are responsible for the performance of the required maintenance listed in your owner's manual. HUSQVARNA recommends that you retain all receipts
covering maintenance on your vehicle engine, but HUSQVARNA cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled
maintenance.
- As the vehicle engine owner, you should however be aware that HUSQVARNA may deny you warranty coverage if vehicle engine or a part has failed due to abuse, neglect, improper
maintenance or unapproved modifications.
- You are responsible for presenting vehicle engine to a HUSQVARNA distribution center as soon as a problem exists. The warranty repairs should be completed in a reasonable amount
of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact WARRANTY SERVICES, HUSQVARNA FOREST & GARDEN, PRODUCT
MARKETING MANAGER – AUTOMOWER, 7349 STATESVILLE ROAD, CHARLOTTE, NC 28269.
HUSQVARNA EXPLANATION OF EMISSION CONTROL WARRANTY:
1. WARRANTY:
HUSQVARNA warrants to the ultimate purchaser and each subsequent purchaser that the SORE or equipment is designed, built and equipped so as to conform with all applicable
regulations; and free from defects in materials and workmanship that cause the failure of a warranted part to be identical in all material respects to that part as described in
HUSQVARNAs application for certification. The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser or first placed into service. The
warranty period is two years.
2. COVERAGE:
Subject to certain conditions and exclusions as stated below, the warranty on emission-related parts is as follows:
(1) Any warranted part that is not scheduled for replacement as required maintenance in the written instructions supplied, is warranted for the warranty period stated above. If the part
fails during the period of warranty coverage, the part will be repaired or replaced by HUSQVARNA according to subsection (4) below. Any such part repaired or replaced under warranty
will be warranted for the remainder of the period.
(2) Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period stated above. Any such part repaired or
replaced under warranty will be warranted for the remaining warranty period.
(3) Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is warranted for the period of time before the first scheduled
replacement date for that part. If the part fails before the first scheduled replacement, the part will be repaired or replaced by HUSQVARNA according to subsection (4) below. Any such
part repaired or replaced under warranty will be warranted for the remainder of the period prior to the first scheduled replacement point for the part.
(4) Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty station* at no charge to the owner.
(5) Notwithstanding the provisions herein, warranty services or repairs will be provided at all of our distribution centers that are franchised to service the subject engines or equipment.
(6) The engine or equipment owner will not be charged for diagnostic labor that is directly associated with diagnosis of a defective, emission-related warranted part, provided that such
diagnostic work is performed at a warranty station*.
(7) HUSQVARNA is liable for damages to other engine or equipment components proximately caused by a failure under warranty of any warranted part.
(8) Throughout the engine or equipment warranty period stated above, HUSQVARNA will maintain a supply of warranted parts sufficient to meet the expected demand for such parts.
(9) Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner. Such use will not reduce the
warranty obligations of HUSQVARNA
(10) Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on or modified parts by the ultimate purchaser will
be grounds for disallowing a warranty claims. HUSQVARNA will not be liable to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.
*HUSQVARNA, its authorized dealers, or a service agency approved by HUSQVARNA.
ITEMS COVERED BY THIS WARRANTY:
The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage if HUSQVARNA demonstrates that the engine
or equipment has been abused, neglected, or improperly maintained, and that such abuse, neglect, or improper maintenance was the direct cause of the need for repair or replacement
of the part. That notwithstanding, any adjustment of a component that has a factory installed, and properly operating, adjustment limiting device is still eligible for warranty coverage. The
following emission warranty parts list are covered:
SYSTEMS COVERED
Fuel Metering
PARTS DESCRIPTION
Carburetor assembly, fuel injection pump, fuel injection nozzle, fuel regulator
Exhaust
Catalyst
Air Induction
Air filter housing, air filter*, crankcase breather tube
Ignition
Flywheel magneto, ignition pulse generator, ignition coil assembly, ignition control module, spark plug cap, spark plug*
PCV valve, oil filler cap
Belts, fuel hose, hosing, tubing, fittings, seals, gasket, and clamps associated with the above systems
Positive Crankcase Ventilation (PCV) System
Misc. Parts
Emission-related parts will vary between vehicles; therefore, certain vehicles my not include all of the listed parts or may include equivalent parts.
3. EXCLUSIONS:
Excluded from this warranty is damage to a vehicle or component resulting from a cause other than a defect including unreasonable or unintended strain or use, improper installation of
accessories, installation of parts or accessories that are not original equipment, overloading, accident, alteration, abuse or neglect. This warranty covers only those failures resulting from
defects in material or workmanship.
Transportation expenses for warranty services are also excluded from this warranty.
4. VOIDING OF WARRANTY:
THIS AND ANY OTHER WARRANTY SHALL BE VOID IF THE VEHICLE IS ABUSED OR USED IN AN UNINTENDED MANNER OR SHOWS INDICATIONS THAT IT HAS BEEN
ALTERED IN ANY WAY, INCLUDING, BUT NOT LIMITED TO, MODIFICATION OF THE SPEED GOVERNOR, BRAKING SYSTEM, STEERING, TRANSAXLE, OR OTHER
OPERATING SYSTEMS OF THE VEHICLE TO CAUSE IT TO PERFORM OUTSIDE HUSQVARNA SPECIFICATIONS. THE WARRANTY IS LIKEWISE VOID IF THE VEHICLE
INVOLVED SHOWS INDICATIONS THAT REASONABLE OR NECESSARY MAINTENANCE AS OUTLINED IN THE OWNERS MANUAL AND MAINTENANCE AND SERVICE
MANUAL WAS NOT PERFORMED AT THE TIME AND IN THE MANNER SPECIFIED IN SUCH MANUALS.
5. NO CONSEQUENTIAL DAMAGES:
In no event shall HUSQVARNA be liable for any incidental or consequential damages including, but not limited to, loss related to property other than the vehicle, loss of use, loss of time,
inconvenience, or any other economic loss. This warranty is applicable only where the California or U.S. EPA emission control system warranty regulation is in effect.
6. HOW TO MAKE A WARRANTY CLAIM:
To make a warranty claim under this limited warranty, you must present the vehicle or defective component to an authorized HUSQVARNA dealer or send the defective component,
freight prepaid, to WARRANTY SERVICES, HUSQVARNA FOREST & GARDEN, PRODUCT MARKETING MANAGER – AUTOMOWER, 7349 STATESVILLE ROAD, CHARLOTTE,
NC 28269
IF THE WARRANTY REGISTRATION FORM IS NOT COMPLETED AND RETURNED TO HUSQVARNA AT THE TIME OF THE ORIGINAL RETAIL SALE, PURCHASER MUST
PROVIDE PROOF OF DATE OF PURCHASE WITH ANY WARRANTY CLAIM.
Page 42
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
EMISSION CONTROL INFORMATION
acts or the causing thereof:(1) the removal or
rendering inoperative by any person other than
for purposes of maintenance, repair, or replace-
ment, of any device or element of design incor-
porated into any new engine for the purposes of
emission control prior to its sale or delivery to the
ultimate purchaser or while it is in use, or (2) the
use of the engine after such device or element of
design has been removed or rendered inopera-
tive by any person.
Among those acts presumed to constitute
tampering are the acts listed below:
Do not tamper with the original emission relat-
ed parts:
• Carburetor and internal parts
• Spark plugs
• Magneto or electronic ignition system
• Fuel filter element
• Air cleaner element
• Crankcase
Fuel Information
THIS VEHICLE IS CERTIFIED TO OPER-
ATE ON UNLEADED REGULAR GRADE to this engine consists of a carburetor and an
GASOLINE ONLY.A minimum of 87 octane of
the anti-knock index is recommended.The anti-
knock index is posted on service station pumps
in the U.S.A.
2.Exhaust Emission Control System
The exhaust emission control system applied
ignition system having optimum ignition timing
characteristics.
The carburetors have been calibrated to
provide lean air/fuel mixture characteristics
and optimum fuel economy with a suitable air
cleaner and exhaust system.
Emission Control Information
To protect the environment in which we all
live, Club Car has incorporated crankcase emis-
sion (1) and exhaust emission (2) control sys-
tems (EM) in compliance with applicable regu-
lations of the U.S.Environmental Protection
Agency and California Air Resources Board.
Maintenance and Warranty
Proper maintenance is necessary to ensure
that your engine will continue to have low emis-
sion levels.Those items identified by the Periodic
Maintenance Chart are necessary to ensure
compliance with the applicable standards.
The Club Car Limited Emission Control
System Warranty requires that you return your
engine to an authorized Club Car Dealer for
remedy under warranty.Please read the warranty
carefully, and keep it valid by complying with
the owner’s obligations it contains.
1.Crankcase Emission Control System
A sealed-type crankcase emission control
system is used to eliminate blow-by gases.The
blow-by gases are led to the breather chamber
through the crankcase.Then, it is led to the air
cleaner.
Oil is separated from the gases while passing
through the inside of the breather chamber
from the crankcase, and then returned back to
the bottom of the crankcase.
• Cylinder head
• Breather chamber and internal parts
• Intake pipe and tube
Tampering with Emission Control
System Prohibited
California State law prohibits the following
FUEL AND OIL RECOMMENDATIONS
MTBE:(Methyl Tertiary Butyl Ether) You may
use gasoline containing up to 15% MTBE by
volume.
Fuel
Use only clean, fresh, unleaded regular grade
gasoline.
WARNING
•After refueling, make sure the tank
cap is closed securely.
METHANOL:(Methanol or Wood Alcohol) 5% by
volume.
Octane Rating
The octane rating of a gasoline is a measure
of its resistance to “knocking”.Use of a mini-
mum of 87 octane of the anti-knock index is
recommended.The anti-knock index is posted on
service station pumps in the U.S.A.
You may use gasoline containing up to 5%
methanol by volume, as long as it also contains
cosolvents and corrosion inhibitors to protect
the fuel system.Gasoline containing more than
5% methanol by volume may cause starting
and/or performance problems.It may also dam-
age metal, rubber, and plastic parts of your fuel
system.
•If gasoline is spilled on the fuel tank
wipe it off immediately.
Oil Viscosity
Choose the viscosity according to the tem-
perature as follows:
NOTE
•If “knocking or pinging”occurs, use a
different brand of gasoline or higher
octane rating.
°
°
°
°
°
°
°
C
40
-20 C -10 C
0 C
20
10 C
30
C
WARNING
SAE 40
•Gasoline is extremely flammable and
can be explosive under certain con-
ditions.Turn the engine switch OFF.
Do not smoke.Make sure the area is
well ventilated and free from any
source of flame or sparks;this
includes any appliance with a pilot
light.Never fill the tank so the fuel
level rises into the filler neck.If the
tank is overfilled, heat may cause
the fuel to expand and overflow
through the vent in the fuel tank.
SAE 30
SAE 10W-30/SAE 10W-40
CAUTION
SAE 5W-20
•Do not mix oil with gasoline.
°
°
F
°
°
°
°
°
104 F
32 F 50
F
86 F
-4 F
14
68 F
Oxygenated Fuel
If you use oxygenated fuel (either ethanol or
MTBE added to gasoline), be sure it is unleaded
and meets the minimum octane rating require-
ment.
NOTE
•Using multi-grade oils (5W-20, 10W-
30, and 10W-40) will increase oil
consumption.Check oil level more
frequently when using them.
The following are the EPA approved percent-
ages of fuel oxygenates.
Engine Oil
The following engine oils are recommended.
API Service Classification:SC, SD, SE, SF,
SG, or SH.
ETHANOL:(Ethyl or Grain Alcohol) You may
use gasoline containing up to 10% ethanol by
volume.
2007 HUV4213 Gasoline Vehicle Owner’s Manual
Page 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Publication Part Number 531 30 81-87
Edition Code 0706A00000
CCI P/N 103218318
Download from Www.Somanuals.com. All Manuals Search And Download.
|