Husqvarna Trimmer 333RJ 335RJX Series User Manual

Operator’s manual (EPA)

333RJ 335RJ

X-series

Please read the operator’s manual carefully and make sure you

understand the instructions before using the machine.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS

Contents

Note the following before starting:

KEY TO SYMBOLS

Please read the operator’s manual carefully.

Symbols .......................................................................

CONTENTS

Maintenance, replacement, or repair of the emission control

devices and system may be performed by any nonroad

engine repair establishment or individual.

Contents ......................................................................

Note the following before starting: ................................

INTRODUCTION

WARNING! Long-term exposure to noise can

Dear customer! ............................................................

WHAT IS WHAT?

result in permanent hearing impairment. So

always use approved hearing protection.

What is what on the clearing saw? ..............................

GENERAL SAFETY PRECAUTIONS

Important ......................................................................

Personal protective equipment .....................................

Machine′s safety equipment ........................................

Cutting equipment ........................................................

ASSEMBLY

WARNING! Under no circumstances may the

design of the machine be modiﬁed without

the permission of the manufacturer. Always

use genuine accessories. Non-authorized

modiﬁcations and/or accessories can result

in serious personal injury or the death of the

operator or others.

Fitting the J-handle ..................................................... 11

Assembling the cutting equipment ............................... 11

Fitting the guard extension ........................................... 11

Fitting a blade guard, grass blade and grass cutter ..... 12

Fitting other guards and cutting attachments ............... 12

FUEL HANDLING

Your warranty may not cover damage or

liability caused by the use of non-authorized

accessories or replacement parts.

WARNING! A clearing saw, brushcutter or

trimmer can be dangerous if used

incorrectly or carelessly, and can cause

serious or fatal injury to the operator or

others. It is extremely important that you

read and understand the contents of this

operator’s manual.

Fuel safety ................................................................... 13

Fuel .............................................................................. 13

Fueling ......................................................................... 14

STARTING AND STOPPING

Check before starting ................................................... 15

Starting and stopping ................................................... 15

WORKING TECHNIQUES

General working instructions ....................................... 17

MAINTENANCE

TWC

Carburetor .................................................................... 19

Mufﬂer .......................................................................... 21

Cooling system ............................................................ 21

Bevel gear .................................................................... 21

Air ﬁlter ......................................................................... 22

Spark plug .................................................................... 22

Maintenance schedule ................................................. 23

TECHNICAL DATA

This label certify that the product has been certiﬁed in

accordance with American exhaust requirements EPA 1.

Technical data .............................................................. 24

FEDERAL EMISSION CONTROL WARRANTY

STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS ..... 25

This engine label certiﬁes that the product is certiﬁed in

accordance with American exhaust emissions requirements

EPA Ph II and CARB Tier II. The Emissions Compliance

Period referred to on the emissions Compliance label

indicates the number of operating hours for which the engine

has been shown to meet Federal and California emisson

requirements.

Category C = 50 hours, B = 125 hours, and A = 300 hours.

English – 3

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

Dear customer!

Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the

Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The

location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. During over

300 years of continuous operation, the Husqvarna factory has produced a lot of different products, from wood stoves to modern

kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the ﬁrst motor driven lawn mowers appeared, followed

by chain saws in 1959, and it is within this area Husqvarna is working today.

Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our highest priority.

We develop, manufacture and market high quality motor driven products for forestry and gardening as well as for building and

construction industry.

Your purchase gives you access to professional help with repairs and service whenever this may be necessary. If the retailer who

sells your machine is not one of our authorized dealers, ask for the address of your nearest servicing dealer.

It is our wish that you will be satisﬁed with your product and that it will be your companion for a long time. Think of this operator′s

manual as a valuable document.By following its′ content (using, service, maintenance etc) the life span and the second-hand value

of the machine can be extended. If you ever lend or sell this machine, make sure that the borrower or buyer gets the operator′s

manual, so they will also know how to properly maintain and use it.

Thank you for using a Husqvarna product.

Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and

appearance of products without prior notice.

For customer assistance, contact us at our website: www.usa.husqvarna.com

4 – English

Download from Www.Somanuals.com. All Manuals Search And Download.

WHAT IS WHAT?

What is what on the clearing saw?

Trimmer head

17 Choke control

18 Air purge

Grease ﬁller cap, bevel gear

Bevel gear

19 Locking nut

20 Support ﬂange

21 Support cup

22 Blade

Cutting attachment guard

Shaft

Handle adjustment

Loop handle

23 Drive disc

Suspension ring

Stop switch

24 Transport guard

25 Spark plug spanner

26 Locking pin

27 Socket spanner

28 Allen key

10 Throttle lock

11 Throttle control

12 Spark plug cap and spark plug

13 Cylinder cover

14 Starter handle

15 Fuel tank

29 Guard extension

30 Harness

31 Operator’s manual (EPA)

16 Air ﬁlter cover

English – 5

Download from Www.Somanuals.com. All Manuals Search And Download.

GENERAL SAFETY PRECAUTIONS

Important

Personal protective equipment

IMPORTANT!

The machine is only designed for trimming grass.

A clearing saw, brushcutter or trimmer can be dangerous if

used incorrectly or carelessly, and can cause serious or

fatal injury to the operator or others. It is extremely

important that you read and understand the contents of this

operator’s manual.

The only accessories you can operate with this engine unit

are the cutting attachments we recommend in the chapter

on Technical data.

Never use the machine if you are tired, if you have drunk

alcohol, or if you are taking medication that could affect your

vision, your judgement or your co-ordination.

You must use approved personal protective equipment

whenever you use the machine. Personal protective

equipment cannot eliminate the risk of injury but it will

reduce the degree of injury if an accident does happen. Ask

your dealer for help in choosing the right equipment.

Wear personal protective equipment. See instructions

under the heading Personal protective equipment.

Never use a machine that has been modiﬁed in any way

from its original speciﬁcation.

WARNING! Listen out for warning signals or

shouts when you are wearing hearing

protection. Always remove your hearing

protection as soon as the engine stops.

Never use a machine that is faulty. Carry out the checks,

maintenance and service instructions described in this

manual.Some maintenance and service measures must be

carried out by trained and qualiﬁed specialists. See

instructions under the heading Maintenance.

HELMET

A protective helmet where there is a risk of falling objects

All covers and guards must be ﬁtted before starting. Ensure

that the spark plug cap and ignition lead are undamaged to

avoid the risk of electric shock.

The machine operator must ensure that no people or

animals come closer than 15 metres while working. When

several operators are working in the same area the safety

distance should be at least twice the tree height and no less

than 15 metres.

HEARING PROTECTION

Wear hearing protection that provides adequate noise

reduction.

WARNING! Running an engine in a conﬁned

or badly ventilated area can result in death

due to asphyxiation or carbon monoxide

poisoning.

EYE PROTECTION

Always wear approved eye protection. If you use a visor then

you must also wear approved protective goggles. Approved

protective goggles must comply with standard ANSI Z87.1 in

the USA or EN 166 in EU countries.

WARNING! Never allow children to use or be

in the vicinity of the machine. As the

machine is equipped with a spring-loaded

stop switch and can be started by low speed

and force on the starter handle, even small

children under some circumstances can

produce the force necessary to start the

machine.This can mean a risk of serious

personal injury.Therefore remove the spark

plug cap when the machine is not under

close supervision.

GLOVES

Gloves should be worn when necessary, e.g., when ﬁtting

cutting attachments.

BOOTS

Wear boots with steel toe-caps and non-slip sole.

6 – English

Download from Www.Somanuals.com. All Manuals Search And Download.

GENERAL SAFETY PRECAUTIONS

CLOTHING

Make sure the throttle control is locked at the idle setting

when the throttle lock is released.

Wear clothes made of a strong fabric and avoid loose clothing

that can catch on twigs and branches. Always wear heavy,

long pants. Do not wear jewellery, shorts sandals or go

barefoot. Secure hair so it is above shoulder level.

FIRST AID KIT

Always have a ﬁrst aid kit nearby.

Press the throttle lock and make sure it returns to its original

position when you release it.

′

Machine s safety equipment

This section describes the machine′s safety equipment, its

purpose, and how checks and maintenance should be carried

out to ensure that it operates correctly. See the ”What is

what?” section to locate where this equipment is positioned

on your machine.

Check that the throttle control and throttle lock move freely

and that the return springs work properly.

IMPORTANT! All servicing and repair work on the machine

requires special training. This is especially true of the

machine′s safety equipment.If your machine fails any of the

checks described below you must contact your service

agent.When you buy any of our products we guarantee the

availability of professional repairs and service. If the retailer

who sells your machine is not a servicing dealer, ask him for

the address of your nearest service agent.

See instructions under the heading Start. Start the machine

and apply full throttle. Release the throttle and check that the

cutting attachment stops and remains at a standstill. If the

cutting attachment rotates with the throttle in the idle position

then the carburettor idle setting must be checked. See

instructions under the heading Maintenance.

WARNING! Never use a machine with faulty

safety equipment.The machine’s safety

equipment must be checked and maintained

as described in this section. If your machine

fails any of these checks contact your

service agent to get it repaired.

Throttle lock

The throttle lock is designed to prevent accidental operation

of the throttle control. When you press the lock (A) (i.e. when

you grasp the handle) it releases the throttle control (B).

When you release the handle the throttle control and the

throttle lock both move back to their original positions. This

movement is controlled by two independent return springs.

This arrangement means that the throttle control is

automatically locked at the idle setting.

Stop switch

Use the stop switch to switch off the engine.

Start the engine and make sure the engine stops when you

move the stop switch to the stop setting.

English – 7

Download from Www.Somanuals.com. All Manuals Search And Download.

GENERAL SAFETY PRECAUTIONS

Check that the vibration damping element is undamaged and

securely attached.

Cutting attachment guard

WARNING! Overexposure to vibration can

lead to circulatory damage or nerve damage

in people who have impaired circulation.

Contact your doctor if you experience

symptoms of overexposure to vibration.

Such symptoms include numbness, loss of

feeling, tingling, pricking, pain, loss of

strength, changes in skin colour or

This guard is intended to prevent loose objects from being

thrown towards the operator. The guard also protects the

operator from accidental contact with the cutting attachment.

condition.These symptoms normally appear

in the ﬁngers, hands or wrists.The risk

increases at low temperatures.

Check that the guard is undamaged and not cracked.Replace

the guard if it has been exposed to impact or is cracked.

Mufﬂer

The mufﬂer is designed to keep noise levels to a minimum

and to direct exhaust fumes away from the user. A mufﬂer

ﬁtted with a catalytic converter is also designed to reduce

harmful exhaust gases.

Always use the recommended guard for the cutting

attachment you are using. See chapter on Technical data.

WARNING! Never use a cutting attachment

without an approved guard. See the chapter

on Technical data. If an incorrect or faulty

guard is ﬁtted this can cause serious

personal injury.

Vibration damping system

In countries that have a warm and dry climate there is a

signiﬁcant risk of ﬁre. We therefore ﬁt certain mufﬂers with a

spark arrestor mesh. Check whether the mufﬂer on your

machine is ﬁtted with this kind of mesh.

Your machine is equipped with a vibration damping system

that is designed to reduce vibration and make operation

easier.

Using incorrectly wound cord or a blunt or incorrect cutting

attachment (wrong type or incorrectly ﬁled, see instructions

under the heading Filing the blade) increases the level of

vibration.

For mufﬂers it is very important that you follow the instructions

on checking, maintaining and servicing your machine.

The machine′s vibration damping system reduces the transfer

of vibration between the engine unit/cutting equipment and

the machine′s handle unit.

Never use a machine that has a faulty mufﬂer.

Regularly check the vibration damping units for cracks or

deformation.

Regularly check that the mufﬂer is securely attached to the

machine.

8 – English

Download from Www.Somanuals.com. All Manuals Search And Download.

GENERAL SAFETY PRECAUTIONS

If the mufﬂer on your machine is ﬁtted with a spark arrestor

Cutting equipment

mesh this must be cleaned regularly. A blocked mesh will

cause the engine to overheat and may lead to serious

damage.

This section describes how to choose and maintain your

cutting equipment in order to:

•

Reduce the risk of blade thrust.

Obtain maximum cutting performance.

Extend the life of cutting equipment.

IMPORTANT!

Only use cutting attachments with the guards we

recommend! See the chapter on Technical data.

WARNING! Mufﬂers ﬁtted with catalytic

converters get very hot during use and

Refer to the instructions for the cutting attachment to check

the correct way to load the cord and the correct cord

diameter.

remain so for some time after stopping.This

also applies at idle speed. Contact can result

in burns to the skin. Remember the risk of

ﬁre!

Keep the teeth of the blade correctly sharpened! Follow our

recommendations. Also refer to the instructions on the

blade packaging.

WARNING! The inside of the mufﬂer contain

Maintain the correct blade setting! Follow our instructions

and use the recommended ﬁle gauge.

chemicals that may be carcinogenic. Avoid

contact with these elements in the event of a

damaged mufﬂer.

WARNING! Always stop the engine before

doing any work on the cutting attachment.

This continues to rotate even after the

throttle has been released. Ensure that the

cutting attachment has stopped completely

and disconnect the HT lead from the spark

plug before you start to work on it.

WARNING! Bear in mind that:

The exhaust fumes from the engine are hot

and may contain sparks which can start a

ﬁre. Never start the machine indoors or near

combustible material!

Locking nut

WARNING! Using an incorrect cutting

attachment or an incorrectly sharpened

blade increases the risk of kickback.

A locking nut is used to secure some types of cutting

attachment.

Cutting equipment

Grass blades and grass cutters are intended for cutting

coarse grass.

When ﬁtting, tighten the nut in the opposite direction to the

direction of rotation of the cutting attachment. To remove it,

undo the nut in the same direction as the cutting attachment

rotates. (CAUTION! The nut has a left-hand thread.) Tighten

the nut using the socket spanner.

A trimmer head is intended for trimming grass.

The nylon lining inside the locking nut must not be so worn

that you can turn it by hand. The lining should offer a

resistance of at least 1.5 Nm. The nut should be replaced

after it has been put on approx. 10 times.

English – 9

Download from Www.Somanuals.com. All Manuals Search And Download.

GENERAL SAFETY PRECAUTIONS

General rules

Trimmer head

IMPORTANT!

Always ensure the trimmer cord is wound tightly and evenly

around the drum, otherwise the machine will generate

harmful vibration.

Only use cutting attachments with the guards we

recommend! See the chapter on Technical data.

•

Only use the recommended trimmer heads and trimmer

cords.These have been tested by the manufacturer to suit

a particular engine size.This is especially important when

a fully automatic trimmer head is used. Only use the

recommended cutting attachment. See the chapter on

Technical data.

Keep the teeth of the blade correctly sharpened! Follow our

instructions and use the recommended ﬁle gauge. An

incorrectly sharpened or damaged blade increases the risk of

accidents.

•

Smaller machines generally require small trimmer heads

and vice versa. This is because when clearing using a

cord the engine must throw out the cord radially from the

trimmer head and overcome the resistance of the grass

being cleared.

Check the cutting attachment for damage or cracks. A

damaged cutting attachment should always be replaced.

The length of the cord is also important. A longer cord

requires greater engine power than a shorter cord of the

same diameter.

•

Make sure that the cutter on the trimmer guard is intact.

This is used to cut the cord to the correct length.

To increase the life of the cord it can be soaked in water

for a couple of days.This will make the line tougher so that

it lasts longer.

Sharpening grass cutters and grass

blades

•

See the cutting attachment packaging for correct

sharpening instructions. Sharpen blades and cutters

using a single-cut ﬂat ﬁle.

Sharpen all edges equally to maintain the balance of the

blade.

WARNING! Always discard a blade that is

bent, twisted, cracked, broken or damaged

in any other way. Never attempt to straighten

a twisted blade so that it can be reused. Only

use original blades of the speciﬁed type.

10 – English

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

Fitting the J-handle

Assembling the cutting equipment

•

Clip the loop handle onto the shaft. Note that the loop

handle must be ﬁtted between the arrows on the shaft.

WARNING!

When ﬁtting the cutting attachment it is

extremely important that the raised section

on the drive disc/support ﬂange engages

correctly in the centre hole of the cutting

attachment. If the cutting attachment is ﬁtted

incorrectly it can result in serious and/or

fatal personal injury.

•

Slide the spacer into the slot in the loop handle.

Fit the nut, knob and screw. Do not overtighten.

WARNING! Never use a cutting attachment

without an approved guard. See the chapter

on Technical data. If an incorrect or faulty

guard is ﬁtted this can cause serious

personal injury.

Attach the J-handle to the loop handle using the three

screws, as shown.

IMPORTANT! If a saw blade or grass blade are to be used

the machine must be equipped with the correct handlebar,

blade guard and harness.

Fitting the guard extension

•

Now adjust the trimmer to give a comfortable working

position. Tighten the bolt/knob.

CAUTION! The guard extension shall always be ﬁtted when

using the trimmer head/plastic blades and combination

guard. The guard extension shall always be removed when

using the grass blade and combination guard.

Enter the guard extension guide in the slot of the combination

guard. Then click the guard extension into position on the

guard with the four quick-fasteners.

WARNING! Only grass blades/grass cutters

or trimmer heads/plastic blades may be used

when the J-handle is ﬁtted. Saw blades must

never be used with the J-handle.

The guard extension is removed easily using the spark plug

spanner, see illustration.

English – 11

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

Fitting a blade guard, grass blade

and grass cutter

Fitting other guards and cutting

attachments

•

Fit the trimmer guard/combination guard (A) intended for

use with the trimmer head/plastic blades. CAUTION!

Ensure that the guard extension is ﬁtted.

Hang the trimmer guard/combination guard (A) on the two

hooks on the plate holder (M). Bend the guard around the

shaft and tighten it with the bolt (L) on the opposite side of

the shaft. Use the locking pin (C). Place the locking pin in

the groove on the screw head and tighten. See diagram.

•

Hook the blade guard/combination guard (A) onto the

ﬁtting on the shaft and secure with the bolt. CAUTION!

Ensure that the guard extension is removed.

•

Fit the drive disc (B) on the output shaft.

Use the recommended blade guard. See the Technical

data section.

•

Fit the drive disc (B) on the output shaft.

Turn the blade shaft until one of the holes in the drive disc

aligns with the corresponding hole in the gear housing.

•

Insert the locking pin (C) in the hole to lock the shaft.

Place the blade (D), support cup (E) and support ﬂange

(F) on the output shaft.

•

Fit the nut (G). The nut must be tightened to a torque of

35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool

kit. Hold the shaft of the spanner as close to the blade

guard as possible. To tighten the nut, turn the spanner in

the opposite direction to the direction of rotation (Caution!

left-hand thread).

•

Turn the blade shaft until one of the holes in the drive disc

aligns with the corresponding hole in the gear housing.

•

Insert the locking pin (C) in the hole to lock the shaft.

Screw on the trimmer head/plastic blades (H) in the

opposite direction to the direction of rotation.

•

To dismantle, follow the instructions in the reverse order.

12 – English

Download from Www.Somanuals.com. All Manuals Search And Download.

FUEL HANDLING

Gasoline

Fuel safety

Never start the machine:

If you have spilt fuel on it. Wipe off the spillage and allow

remaining fuel to evaporate.

CAUTION! Always use a quality gasoline/oil mixture with an

octane rating of at least 87 octane ((RON+MON)/2). If your

machine is equipped with a catalytic converter (see chapter

on Technical data) always use a good quality unleaded

gasoline/oil mixture.Leaded gasoline will destroy the catalytic

converter.

If you have spilt fuel on yourself or your clothes, change

your clothes.Wash any part of your body that has come in

contact with fuel. Use soap and water.

If the machine is leaking fuel. Check regularly for leaks

from the fuel cap and fuel lines.

Use low-emission gasoline, also known as alkylate gasoline,

if it is available.

Transport and storage

•

Store and transport the machine and fuel so that there is

no risk of any leakage or fumes coming into contact with

sparks or naked ﬂames, for example, from electrical

machinery, electric motors, electrical relays/switches or

boilers.

•

When storing and transporting fuel always use approved

containers intended for this purpose.

This engine is certiﬁed to operate on unleaded gasoline.

•

The lowest recommended octane grade is 87

When storing the machine for long periods the fuel tank

must be emptied.Contact your local gas station to ﬁnd out

where to dispose of excess fuel.

((RON+MON)/2). If you run the engine on a lower octane

grade than 87 so-called knocking can occur. This gives

rise to a high engine temperature and increased bearing

load, which can result in serious engine damage.

•

Ensure the machine is cleaned and that a complete

service is carried out before long-term storage.

•

When working at continuous high revs a higher octane

rating is recommended.

The transport guard must always be ﬁtted to the cutting

attachment when the machine is being transported or in

storage.

Two-stroke oil

•

In order to prevent unintentional starting of the engine, the

spark plug cap must always be removed during long-term

storage, if the machine is not under close supervision and

when performing all service measures.

•

For best results and performance use HUSQVARNA two-

stroke engine oil, which is specially formulated for our air-

cooled two stroke-engines.

•

Never use two-stroke oil intended for water-cooled

engines, sometimes referred to as outboard oil (rated

TCW).

WARNING! Take care when handling fuel.

Bear in mind the risk of ﬁre, explosion and

inhaling fumes.

•

Never use oil intended for four-stroke engines.

Mixing ratio

1:50 (2%) with HUSQVARNA two-stroke oil.

Fuel

CAUTION! The machine is equipped with a two-stroke

engine and must always been run using a mixture of gasoline

and two-stroke engine oil. It is important to accurately

measure the amount of oil to be mixed to ensure that the

correct mixture is obtained. When mixing small amounts of

fuel, even small inaccuracies can drastically affect the ratio of

the mixture.

Two-stroke oil, litre

Gasoline, litre

2% (1:50)

0,10

0,20

0,30

0,40

US gallon

US ﬂ. oz.

2 1/2

6 1/2

12 7/8

WARNING! Fuel and fuel fumes are highly

inﬂammable and can cause serious injury

when inhaled or allowed to come in contact

with the skin. For this reason observe

caution when handling fuel and make sure

there is adequate ventilation.

2 1/2

English – 13

Download from Www.Somanuals.com. All Manuals Search And Download.

FUEL HANDLING

Mixing

Fueling

•

Always mix the gasoline and oil in a clean container

intended for fuel.

•

Always start by ﬁlling half the amount of the gasoline to be

used. Then add the entire amount of oil. Mix (shake) the

fuel mixture. Add the remaining amount of gasoline.

WARNING!Taking the following precautions,

will lessen the risk of ﬁre:

•

Mix (shake) the fuel mixture thoroughly before ﬁlling the

machine’s fuel tank.

Do not smoke or place hot objects near fuel.

Always shut off the engine before refuelling.

Always stop the engine and let it cool for a

few minutes before refuelling.

When refuelling, open the fuel cap slowly so

that any excess pressure is released gently.

Tighten the fuel cap carefully after refuelling.

Always move the machine away from the

refuelling area before starting.

•

Do not mix more than one month’s supply of fuel at a time.

•

Clean the area around the fuel cap. Contamination in the

tank can cause operating problems.

If the machine is not used for some time the fuel tank

should be emptied and cleaned.

Ensure that the fuel is well mixed by shaking the container

before ﬁlling the tank.

WARNING! The catalytic converter mufﬂer

gets very hot during and after use.This also

applies during idling. Be aware of the ﬁre

hazard, especially when working near

ﬂammable substances and/or vapours.

14 – English

Download from Www.Somanuals.com. All Manuals Search And Download.

STARTING AND STOPPING

Check before starting

Starting and stopping

•

Check the blade to ensure that no cracks have formed at

the bottom of the teeth or by the centre hole. The most

common reason why cracks are formed is that sharp

corners have been formed at the bottom of the teeth while

sharpening or that the blade has been used with dull

teeth. Discard a blade if cracks are found.

WARNING! The complete clutch cover and

shaft must be ﬁtted before the machine is

started, otherwise the clutch can come loose

and cause personal injury.

Always move the machine away from the

refuelling area before starting. Place the

machine on a ﬂat surface. Ensure the cutting

attachment cannot come into contact with

any object.

Make sure no unauthorised persons are in

the working area, otherwise there is a risk of

serious personal injury.The safety distance

is 15 metres.

•

Check that the support ﬂange is not cracked due to fatigue

or due to being tightened too much. Discard the support

ﬂange if it is cracked.

Starting

Choke: Set the choke control in the choke position.

•

Ensure the locking nut has not lost its captive force. The

nut lock should have a locking force of at least 1.5 Nm.

The tightening torque of the locking nut should be 35-50

Nm.

Check that the blade guard is not damaged or cracked.

Replace the blade guard if it is exposed to impact or is

cracked.

Primer bulb: Press the air purge repeatedly until fuel begins

to ﬁll the bulb. The bulb need not be completely ﬁlled.

•

Check that the trimmer head and trimmer guard are not

damaged or cracked. Replace the trimmer head or

trimmer guard if they have been exposed to impact or are

cracked.

WARNING! When the engine is started with

the choke in either the choke or start throttle

positions the cutting attachment will start to

rotate immediately.

Hold the body of the machine on the ground using your left

hand (CAUTION! Not with your foot!). Grip the starter handle,

slowly pull out the cord with your right hand until you feel

some resistance (the starter pawls grip), now quickly and

powerfully pull the cord.Never wrap the starter cord around

your hand

Repeat pulling the cord until the engine starts. When the

engine starts. return choke control to run position and apply

full throttle; the throttle will automatically disengage from the

start setting.

•

Never use the machine without a guard nor with a

defective guard.

All covers must be correctly ﬁtted and undamaged before

you start the machine.

English – 15

Download from Www.Somanuals.com. All Manuals Search And Download.

STARTING AND STOPPING

CAUTION! Do not pull the starter cord all the way out and do

not let go of the starter handle when the cord is fully extended.

This can damage the machine.

CAUTION! Do not put any part of your body in marked area.

Contact can result in burns to the skin, or electrical shock if

the spark plug cap has been damaged. Always use gloves.

Do not use a machine with damaged spark plug cap.

Stopping

Stop the engine by switching off the ignition.

CAUTION! The stop switch automatically returns to the start

position. In order to prevent unintentional starting, the spark

plug cap must be removed from the spark plug when

assembling, checking and/or performing maintenance.

16 – English

Download from Www.Somanuals.com. All Manuals Search And Download.

WORKING TECHNIQUES

Keep the cutting attachment below waist level.

General working instructions

Switch off the engine before moving to another area. Fit

the transport guard before carrying or transporting the

equipment any distance.

IMPORTANT!

This section describes the basic safety precautions for

working with clearing saws and trimmers.

Never put the machine down with the engine running

unless you have it in clear sight.

If you encounter a situation where you are uncertain how to

proceed you should ask an expert. Contact your dealer or

your service workshop.

WARNING! Neither the operator of the

machine nor anyone else may attempt to

remove the cut material while the engine is

running or the cutting equipment is rotating,

as this can result in serious injury.

Avoid all usage which you consider to be beyond your

capability.

You must understand the difference between forestry

clearing, grass clearing and grass trimming before use.

Stop the engine and cutting equipment

before you remove material that has wound

around the blade shaft as otherwise there is

a risk of injury.The bevel gear can get hot

during use and may remain so for a while

afterwards.You could get burnt if you touch

it.

Basic safety rules

•

Look around you:

To ensure that people, animals or other things cannot

affect your control of the machine.

WARNING! Watch out for thrown objects.

Always wear approved eye protection. Never

lean over the cutting attachment guard.

Stones, rubbish, etc. can be thrown up into

the eyes causing blindness or serious injury.

•

To ensure that people, animals, etc., do not come into

contact with the cutting attachment or loose objects that

are thrown out by the cutting attachment.

Keep unauthorised persons at a distance.

Children, animals, onlookers and helpers

should be kept outside the safety zone of 15

m. Stop the machine immediately if anyone

approaches. Never swing the machine

•

CAUTION! Do not use the machine unless you are able to

call for help in the event of an accident.

Do not use the machine in bad weather, such as dense

fog, heavy rain, strong wind, intense cold, etc. Working in

bad weather is tiring and often brings added risks, such as

icy ground, unpredictable felling direction, etc.

around without ﬁrst checking behind you to

make sure no-one is within the safety zone.

Make sure you can move and stand safely.Check the area

around you for possible obstacles (roots, rocks, branches,

ditches, etc.) in case you have to move suddenly. Take

great care when working on sloping ground.

Basic working techniques

Always slow the engine to idle speed after each working

operation. Long periods at full throttle without any load on the

engine can lead to serious engine damage.

WARNING! Sometimes branches or grass

get caught between the guard and cutting

attachment. Always stop the engine before

cleaning.

WARNING! Avoid cutting with the area of the

blade between the 12 o’clock and 3 o’clock

positions. Because of the speed of rotation

of the blade kickback can occur if you

attempt to cut thick stems with this area of

the blade.

Keep a good balance and a ﬁrm foothold.

Always hold the machine with both hands. Hold the

machine on the right side of your body.

English – 17

Download from Www.Somanuals.com. All Manuals Search And Download.

WORKING TECHNIQUES

Clearing

Grass clearing using a grass blade

•

The clearing technique removes all unwanted vegetation.

Keep the trimmer head just above the ground and tilt it.Let

the end of the cord strike the ground around trees, posts,

statues and the like. CAUTION! This technique increases

the wear on the cord.

•

Grass blades and grass cutters must not be used on

woody stems.

•

A grass blade is used for all types of tall or coarse grass.

The grass is cut down with a sideways, swinging

movement, where the movement from right-to-left is the

clearing stroke and the movement from left-to-right is the

return stroke. Let the left-hand side of the blade (between

8 and 12 o’clock) do the cutting.

•

The cord wears quicker and must be fed forward more

often when working against stones, brick, concrete, metal

fences, etc., than when coming into contact with trees and

wooden fences.

When trimming and clearing you should use less than full

throttle so that the cord lasts longer and to reduce the

wear on the trimmer head.

Cutting

•

If the blade is angled to the left when clearing grass, the

grass will collect in a line, which makes it easier to collect,

e.g. by raking.

Try to work rhythmically. Stand ﬁrmly with your feet apart.

Move forward after the return stroke and stand ﬁrmly

again.

•

The trimmer is ideal for cutting grass that is difﬁcult to

reach using a normal lawn mower. Keep the cord parallel

to the ground when cutting. Avoid pressing the trimmer

head against the ground as this can ruin the lawn and

damage the tool.

•

Let the support cup rest lightly against the ground. It is

used to protect the blade from hitting the ground.

Reduce the risk of material wrapping around the blade by

following these instructions:

Always work at full throttle.

Avoid the previously cut material during the return

stroke.

•

Do not allow the trimmer head to constantly come into

contact with the ground during normal cutting. Constant

contact of this type can cause damage and wear to the

trimmer head.

•

Stop the engine, unclip the harness and place the

machine on the ground before you start to collect the cut

material.

Sweeping

Grass trimming with a trimmer head

•

The fan effect of the rotating cord can be used for quick

and easy clearing up. Hold the cord parallel to and above

the area to be swept and move the tool to and fro.

Trimming

•

Hold the trimmer head just above the ground at an angle.

It is the end of the cord that does the work. Let the cord

work at its own pace. Never press the cord into the area

to be cut.

•

When cutting and sweeping you should use full throttle to

obtain the best results.

•

The cord can easily remove grass and weeds up against

walls, fences, trees and borders, however it can also

damage sensitive bark on trees and bushes, and damage

fence posts.

Reduce the risk of damaging plants by shortening the

cord to 10-12 cm and reducing the engine speed.

18 – English

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

Basic setting

Carburetor

•

The basic carburetor settings are adjusted during testing

at the factory. The basic setting is richer than the optimal

setting and should be maintained for the ﬁrst few hours the

machine is in use. The carburettor should then be ﬁnely

adjusted. Fine adjustment should be carried out by a

skilled technician.

Your Husqvarna product has been designed and

manufactured to speciﬁcations that reduce harmful

emissions. After the engine has used 8-10 tanks of fuel the

engine will be run-in.To ensure that it continues to run at peak

performance and to minimise harmful exhaust emissions

after the running-in period, ask your dealer/service workshop

(who will have a rev counter at their disposal) to adjust your

carburettor.

CAUTION! If the cutting attachment rotates when the engine

is idling the idle adjustment screw T should be turned anti-

clockwise until the cutting attachment stops.

WARNING! The complete clutch cover and

shaft must be ﬁtted before the machine is

started, otherwise the clutch can come loose

Rec. idle speed See the Technical data section.

Recommended max. speed: See theTechnical data section.

and cause personal injury.

WARNING! If the idle speed cannot be

adjusted so that the cutting attachment

stops, contact your dealer/service

workshop. Do not use the machine until it

has been correctly adjusted or repaired.

Function

•

The carburetor governs the engine’s speed via the throttle

control. Air and fuel are mixed in the carburetor. The air/

fuel mixture is adjustable. Correct adjustment is essential

to get the best performance from the machine.

Fine adjustment

•

When the machine has been ”run-in” the carburetor

should be ﬁnely adjusted. The ﬁne adjustment should

be carried out by a qualiﬁed person. First adjust the L-

jet, then the idling screw T and then the H-jet.

•

The setting of the carburetor means that the engine is

adapted to local conditions, for example, the climate,

altitude, fuel and the type of 2-stroke oil.

Conditions

The carburetor has three adjustment controls:

L = Low speed jet

•

Before any adjustments are made, make sure that the air

ﬁlter is clean and the air ﬁlter cover is ﬁtted. If you adjust

the carburettor when the air ﬁlter is dirty it will result in a

leaner mixture when the ﬁlter is ﬁnally cleaned. This can

lead to serious engine damage.

H = High speed jet

T = Idle adjustment screw

•

Carefully turn both jets, L and H, so that they are midway

between fully screwed in and fully screwed out.

Do not attempt to adjust the L and H jets beyond either

stop as this could cause damage.

Now start the machine according to the starting

instructions and let it warm up for 10 minutes.

CAUTION! If the cutting attachment rotates when the

engine is idling the idle adjustment screw T should be

turned anti-clockwise until the cutting attachment stops.

•

The L and H-jets are used to adjust the supply of fuel to

match the rate that air is admitted, which is controlled with

the throttle. If they are screwed clockwise the air/fuel ratio

becomes leaner (less fuel) and if they are turned anti-

clockwise the ratio becomes richer (more fuel). A lean

mixture gives a higher engine speed and a rich mixture

gives a lower engine speed.

The T-screw regulates the throttle setting at idle speed. If

the T-screw is turned clockwise this gives a higher idle

speed; turning it anti-clockwise gives a lower idle speed.

English – 19

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

Low speed jet L

High speed jet H

Try to ﬁnd the highest idling speed, turning the low speed

needle L clockwise respectively counter-clockwise.When the

highest speed has been found, turn the low speed needle L 1/

4 turn counter-clockwise.

The high speed jet H affects the engine power, speed,

temperature and fuel consumption. If the high speed jet H is

set too lean (screwed in too far) the engine speed will be too

high and cause engine damage. Do not let the engine run at

full speed for more than 10 seconds.

CAUTION! If the cutting attachment rotates when the engine

is idling the idle adjustment screw T should be turned anti-

clockwise until the cutting attachment stops.

Note that the engine should be loaded when you adjust the

high speed jet H.You should therefore ﬁt the trimmer head

T35 (2.7 mm cord) before adjusting the high speed jet. The

cord length should be standard, i.e.to the knife on the trimmer

guard.

Fine adjustment of the idle speedT

Adjust the idle speed using the idle adjustment screw T, if it is

necessary to readjust. First turn the idle adjustment screw T

clockwise until the cutting attachment starts to rotate. Then

turn the screw anticlockwise until the cutting attachment

stops. The idle speed is correctly adjusted when the engine

will run smoothly in every position.The idle speed should also

be well below the speed at which the cutting attachment starts

to rotate.

Apply full throttle and turn the high speed jet H very slowly

clockwise until the engine slows down. Then turn the high

speed jet H very slowly anticlockwise until the engine starts to

run unevenly. Now turn the high speed jet H slowly clockwise

a little way until the engine runs smoothly.

CAUTION! For optimum adjustment of the carburettor,

contact a qualiﬁed dealer/service workshop that has a

revolution counter at their disposal.

WARNING! If the idle speed cannot be

adjusted so that the cutting attachment

stops, contact your dealer/service

workshop. Do not use the machine until it

has been correctly adjusted or repaired.

Correctly adjusted carburetor

When the carburetor is correctly adjusted the machine will

accelerate without hesitation and burble a little at maximum

speed. It is also important that the cutting attachment does

not rotate at idle. If the low speed jet L is set too lean it may

cause starting difﬁculties and poor acceleration.

If the high speed jet H is set too lean it will result in less power,

less performance, poor acceleration and/or damage to the

engine.

If both the L and H jets are set too rich it will results in

acceleration problems or too low a working speed.

20 – English

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

Mufﬂer

Cooling system

CAUTION! Some mufﬂers are ﬁtted with a catalytic

converter. See chapter on Technical data to see whether your

machine is ﬁtted with a catalytic converter.

To keep the working temperature as low as possible the

machine is equipped with a cooling system.

The mufﬂer is designed to reduce the noise level and to direct

the exhaust gases away from the operator. The exhaust

gases are hot and can contain sparks, which may cause ﬁre

if directed against dry and combustible material.

The cooling system consists of:

Air intake on the starter.

Some mufﬂers are equipped with a special spark arrestor

mesh. If your machine has this type of mufﬂer, you should

clean the mesh at least once a week.This is best done with a

wire brush.On mufﬂers without a catalytic converter the mesh

should be cleaned weekly, or replaced if necessary. On

mufﬂers ﬁtted with a catalytic converter the mesh should be

checked, and if necessary cleaned, monthly. If the mesh is

damaged it should be replaced. If the mesh is frequently

blocked, this can be a sign that the performance of the

catalytic converter is impaired. Contact your dealer to inspect

the mufﬂer. A blocked mesh will cause the machine to

overheat and result in damage to the cylinder and piston.

Cooling ﬁns on the cylinder.

Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more

often in demanding conditions. A dirty or blocked cooling

system results in the machine overheating which causes

damage to the piston and cylinder.

Bevel gear

The bevel gear is ﬁlled with the right quantity of grease at the

factory. However, before using the machine you should check

that the bevel gear is ﬁlled three-quarters full with grease.Use

HUSQVARNA special grease.

CAUTION! Never use a machine with a defective mufﬂer.

The grease in the bevel gear does not normally need to be

changed except if repairs are carried out.

WARNING! Mufﬂers ﬁtted with catalytic

converters get very hot during use and

remain so for some time after stopping.This

also applies at idle speed. Contact can result

in burns to the skin. Remember the risk of

ﬁre!

English – 21

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

Air ﬁlter

Spark plug

The air ﬁlter must be regularly cleaned to remove dust and dirt

in order to avoid:

The spark plug condition is inﬂuenced by:

•

Incorrect carburetor adjustment.

•

Carburettor malfunctions

Starting problems

An incorrect fuel mixture (too much or incorrect type of

oil).

Loss of engine power

•

A dirty air ﬁlter.

Unnecessary wear to engine parts

Excessive fuel consumption.

These factors cause deposits on the spark plug electrodes,

which may result in operating problems and starting

difﬁculties.

If the machine is low on power, difﬁcult to start or runs poorly

at idle speed: always check the spark plug ﬁrst before taking

any further action. If the spark plug is dirty, clean it and check

that the electrode gap is 0.5 mm (0,020"). The spark plug

should be replaced after about a month in operation or earlier

if necessary.

Clean the ﬁlter every 25 hours, or more regularly if conditions

are exceptionally dusty.

Cleaning the air ﬁlter

Remove the air ﬁlter cover and take out the ﬁlter. Wash it

clean in warm, soapy water. Ensure that the ﬁlter is dry before

reﬁtting it.

CAUTION! Always use the recommended spark plug type!

Use of the wrong spark plug can damage the piston/cylinder.

Check that the spark plug is ﬁtted with a suppressor.

An air ﬁlter that has been in use for a long time cannot be

cleaned completely.The ﬁlter must therefore be replaced with

a new one at regular intervals. A damaged air ﬁlter must

always be replaced.

Note: Use only HUSQVARNA replacement parts. Use of

other brands of replacement parts can cause damage to

your unit or injury to the operator or others.Your warranty

does not cover damage or liability caused by the use of

accessories and/or attachments not speciﬁcally

recommended by HUSQVARNA.

If the machine is used in dusty conditions the air ﬁlter should

be soaked in oil.See instructions under the heading Oiling the

air ﬁlter.

Oiling the air ﬁlter

Always use special ﬁlter oil. Filter oil contains a solvent to

make it spread evenly through the ﬁlter.You should therefore

avoid skin contact.

Put the ﬁlter in a plastic bag and pour the ﬁlter oil over it.

Knead the plastic bag to distribute the oil. Squeeze the

excess oil out of the ﬁlter inside the plastic bag and pour off

the excess before ﬁtting the ﬁlter to the machine. Never use

common engine oil. This would drain through the ﬁlter quite

quickly and collect in the bottom.

22 – English

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the

Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive

work must be carried out by an authorised service workshop.

Daily

maintenance

Weekly

maintenance

Monthly

maintenance

Maintenance

Clean the outside of the machine.

Make sure the throttle trigger lock and the throttle function correctly from a

safety point of view.

Check that the stop switch works correctly.

Check that the cutting attachment does not rotate at idle.

Clean the air ﬁlter. Replace if necessary.

Check that the guard is undamaged and not cracked. Replace the guard if

it has been exposed to impact or is cracked.

Check that the trimmer head is undamaged and not cracked. Replace the

trimmer head if necessary.

Check that the locking nut of the cutting equipment is tighten correctly.

Check that nuts and screws are tight.

Check that there are no fuel leaks from the engine, tank or fuel lines.

Check the starter and starter cord.

Check that the vibration damping elements are not damaged.

Clean the outside of the spark plug. Remove it and check the electrode

gap. Adjust the gap to 0.5 mm (.20”), or replace the spark plug. Check that

the spark plug is ﬁtted with a suppressor.

Clean the machines cooling system.

Clean or replace the spark arrestor mesh on the mufﬂer (only applies to

mufﬂers without a catalytic converter).

Clean the outside of the carburettor and the space around it.

Check that the bevel gear is ﬁlled three-quarters full with lubricant. Fill if

necessary using special grease.

Check the fuel ﬁlter from contamination and the fuel hose from cracks or

other defects. Replace if necessary.

Check all cables and connections.

Check the clutch, clutch springs and the clutch drum for wear. Replace if

necessary by an autorized service workshop.

Replace the spark plug. Check that the spark plug is ﬁtted with a

suppressor.

Check and clean the spark arrestor mesh on the mufﬂer (only applies to

mufﬂers ﬁtted with a catalytic converter).

English – 23

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL DATA

Technical data

333RJ

335RJx

Engine

Cylinder displacement, cu.in/cm

Cylinder bore, inch/mm

Stroke, inch/mm

2,11/34,6

1,50/38,0

1,20/30,5

2900

2,11/34,6

1,50/38,0

1,20/30,5

2900

Idle speed, rpm

Recommended max. fast idle speed, rpm

Speed of output shaft, rpm

11500

8220

Max. engine output, acc. to ISO 8893, kW/ rpm

Catalytic converter mufﬂer

Speed-regulated ignition system

Ignition system

1,6/8400

Yes

Manufacturer/type of ignition system

Spark plug

Walbro MB

NGK CMR6A

0,02/0,5

Walbro MB

NGK CMR6A

0,02/0,5

Electrode gap, inch/mm

Fuel and lubrication system

Manufacturer/type of carburetor

Fuel tank capacity, US pint/litre

Weight

Zama C1Q

1,27/0,6

Zama C1Q

1,27/0,6

Weight without fuel, cutting attachment and guard, Lbs/kg 13,0/5,9

13,2/6,0

Sound levels

(see note 1)

Equivalent sound pressure level at the user′s ear,

measured according to ANSI B175.3-2003, dB(A),

min/max:

99/100

98/100

Vibration levels

Vibration levels at handles, measured according to

ANSI B175.3-2003, m/s

At max. speed, left/right handles, min.:

At max. speed, left/right handles, max.:

2,7/4,8

3,5/5,6

3,8/4,2

5,3/5,7

Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various

working conditions with the following time distribution: 1/2 idle and 1/2 max. speed.

NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting

equipment ﬁtted. The table indicates the highest and lowest values.

Approved accessories

Type

Cutting attachment guard, Art. no.

Centre hole in blades/cutters, Ø 25,4 mm

Output shaft thread M12

Multi 255-3 (Ø 255 3 teeth)

537 33 16-03

Grass blade/grass cutter

Plastic blades

Grass 255-4 (Ø 255 4 teeth)

537 33 16-03

Multi 275-4 (Ø 275 4 teeth)

537 33 16-03

Tricut Ø 300 mm

537 33 16-03

T35

537 33 16-03 / 537 34 94-03

Trimmer head

S35

T45

Support cup

503 89 01-02

24 – English

Download from Www.Somanuals.com. All Manuals Search And Download.

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

your warranty rights and responsibilities, you should contact

your nearest authorized servicing dealer or call Husqvarna

Forest & Garden at 1-800-487-5963.

YOUR WARRANTY RIGHTS AND

OBLIGATIONS

WARRANTY PERIOD Any warranted part which is not

scheduled for replacement as required maintenance, or

which is scheduled only for regular inspection to the effect of

“repair or replace as necessary” shall be warranted for 2

years.Any warranted part which is scheduled for replacement

as required maintenance shall be warranted for the period of

time up to the ﬁrst scheduled replacement point for that part.

The EPA (The US Environmental Protection Agency), CARB

(California Air Resources Board) and Husqvarna Forest &

Garden are pleased to explain the emissions control system

warranty on your 2001 and later small nonroad engine.In U.S.

and Canada, new small nonroad engines must be designed,

built and equipped to meet the federal stringent anti-smog

standards. Husqvarna Forest & Garden must warrant the

emission control system on your small nonroad engine for the

period of time listed below provided there has been no abuse,

neglect or improper maintenance of your unit.Your emission

control system includes Parts such as the carburetor and the

ignition system. Where a warrantable condition exists,

Husqvarna Forest & Garden will repair your small nonroad

engine at no cost to you. Expenses covered under warranty

include diagnosis, parts and labor.

DIAGNOSIS The owner shall not be charged for diagnostic

labor which leads to the determination that a warranted part

is defective, if the diagnostic work is performed at an

approved Husqvarna Forest & Garden servicing dealer.

CONSEQUENTIAL DAMAGES Husqvarna Forest & Garden

may be liable for damages to other engine components

caused by the failure of a warranted part still under warranty.

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper

maintenance are not covered.

′

MANUFACTURER S WARRANTY

COVERAGE

The 2001 and later small nonroad engines are warranted for

two years. If any emission related part on you engine (as

listed above) is defective, the part will be repaired or replaced

by Husqvarna Forest & Garden.

ADD -ON OR MODIFIED PARTS

The use of add-on or modiﬁed parts can be grounds for

disallowing a warranty claim. Husqvarna Forest & Garden is

not liable to cover failures of warranted parts caused by the

use of add-on or modiﬁed parts.

′

OWNER SWARRANTY RESPONSIBILITIES

As the small nonroad engine owner, you are responsible for

the performance of the required maintenance listed in your

Operator′s Manual. Husqvarna Forest & Garden

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights and

responsibilities, you should contact your nearest authorized

servicing dealer or call Husqvarna Forest & Garden at 1-800-

487-5963.

recommends that you retain all receipts covering

maintenance on your small nonroad engine, but Husqvarna

Forest & Garden cannot deny warranty solely for the lack of

receipts or for your failure to ensure the performance of all

scheduled maintenance. As the small nonroad engine owner,

you should, however, be aware that Husqvarna Forest &

Garden may deny you warranty coverage if your small

nonroad engine or a part of it has failed due to abuse, neglect,

improper maintenance, unapproved modiﬁcations or the use

of parts not made or approved by the original equipment

manufacturer.You are responsible for presenting your small

nonroad engine to a Husqvarna Forest & Garden authorized

servicing dealer as soon as a problem exists. The warranty

repairs should be completed in a reasonable amount of time,

not to exceed 30 days. If you have any questions regarding

your warranty rights and responsibilities, you should contact

your nearest authorized servicing dealer or call Husqvarna

Forest & Garden at 1-800-487-5963.

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs shall be provided at all

Husqvarna Forest & Garden authorized servicing dealers.

MAINTENANCE, REPLACEMENT AND

REPAIR OF EMISSION-RELATED PARTS

Any Husqvarna Forest & Garden approved replacement part

used in the performance of any warranty maintenance or

repairs on emission-related parts, will be provided without

charge to the owner if the part is under warranty.

EMISSION CONTROL WARRANTY PARTS

LIST

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date small nonroad engine

is delivered.

Carburetor and internal parts

Intake pipe, airﬁlter holder and carburetor bolts.

Airﬁlter and fuelﬁlter covered up to maintenance schedule.

Ignition System

LENGTH OF COVERAGE

Spark Plug, covered up to maintenance schedule

Ignition Module

Husqvarna Forest & Garden warrants to the initial owner and

each subsequent purchaser that the engine is free from

defects in materials and workmanship which cause the failure

of a warranted part for a period of two years.

Mufﬂer with catalytic converter

MAINTENANCE STATEMENT

The owner is responsible for the performance of all required

maintenance, as deﬁned in the operator’s manual.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS Repair or

replacement of any warranted part will be performed at no

charge to the owner at an approved Husqvarna Forest &

Garden servicing dealer. If you have any questions regarding

English – 25

Download from Www.Somanuals.com. All Manuals Search And Download.

S35

8,5 m

28'

10 cm

4,2 m

14'

"Clic"

15 cm

Download from Www.Somanuals.com. All Manuals Search And Download.

S35

4,25 m

14'

4,25 m

14'

15 cm

Download from Www.Somanuals.com. All Manuals Search And Download.

T35

8,5 m

28'

10 cm

4,3 m

14'

"Clic"

15 cm

Download from Www.Somanuals.com. All Manuals Search And Download.

T45

10 m

32'

10 cm

4,3 m

14'

15 cm

"Clic"

´®z+R33¶5Q¨

Download from Www.Somanuals.com. All Manuals Search And Download.

1150191-95

´®z+R33¶5Q¨

2006-04-05

Download from Www.Somanuals.com. All Manuals Search And Download.

Graco Baby Jumper 16552 5 02 User Manual
Grizzly Air Compressor H6310 User Manual
Grizzly Saw G0728 User Manual
Haier Washer XQSB60 JN User Manual
Hamilton Beach Iron 840104900 User Manual
Hans Grohe Plumbing Product 06094000 User Manual
Hotpoint Double Oven 6182 User Manual
Hotpoint Washer 9518 User Manual
HP Hewlett Packard Computer Monitor C9V73A8#ABA User Manual
Hunter Fan Outdoor Ceiling Fan 42676 01 User Manual