16530 EXL
OPERATOR'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Whencleaning,repairingorinspectingthesnowthrower,
stop the engine and make certain the collector/impel-
ler and all moving parts have stopped. Disconnect
the spark plug wire and keep the wire away from the
plug to prevent someone from accidentally starting the
engine.
7. Do not run the engine indoors, except when starting
the engine and for transporting the snow thrower in or
out of the building. Open the outside doors; exhaust
fumes are dangerous.
Clearing a Clogged Discharge Chute
Handcontactwiththerotatingimpellerinsidethedischarge
chute is the most common cause of injury associated with
snow throwers. Never use your hand to clean out the dis-
charge chute. To clear the chute:
1. SHUT THE ENGINE OFF!
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean-out tool, not your hands.
8. Exercise extreme caution when operating on slopes.
Maintenance and Storage
1. Check shear bolts and other bolts at frequent intervals
for proper tightness to be sure the equipment is in safe
working condition.
2. Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present
such as hot water heaters, space heaters, or clothes
dryers. Allow the engine to cool before storing in any
enclosure.
3. Always refer to operator’s manual for important details
if the snow thrower is to be stored for an extended
period.
9. Neveroperatethesnowthrowerwithoutproperguards,
and other safety protective devices in place and work-
ing.
10. Never direct the discharge toward people or areas
where property damage can occur. Keep children and
others away.
11. Do not overload the machine capacity by attempting
to clear snow at too fast a rate.
12. Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care when
operating in reverse.
13. Disengage power to the collector/impeller when snow
thrower is transported or not in use.
14. Use only attachments and accessories approved by
the manufacturer of the snow thrower (such as wheel
weights, counterweights, or cabs).
4. Maintain or replace safety and instruction labels, as
necessary.
5. Run the machine a few minutes after throwing snow
to prevent freeze-up of the collector/impeller.
15. Never operate the snow thrower without good visibility
or light. Always be sure of your footing, and keep a firm
hold on the handles. Walk; never run.
16. Never touch a hot engine or muffler.
CONGRATULATIONS on your purchase of a new snow
thrower. It has been designed, engineered and manu-
factured to give best possible dependability and perfor-
mance.
PRODUCT SPECIFICATIONS
Gasoline Capacity 4.0 Quarts (3,79 Liters)
and Type:
Unleaded Regular only
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
center. We have competent, well-trained technicians and
the proper tools to service or repair this unit.
Oil Type
(API SG–SL):
SAE 5W-30 or 10W-30
(0°F to +40°F / –18°C to +5°C)
Synthetic SAE 5W-30 or 10W-30
(below 0°F / –18°C)
Please read and retain this manual. The instructions will
enable you to assemble and maintain your snow thrower
properly. Always observe the “SAFETY RULES”.
Oil Capacity:
28 Ounces (0,8 Liters)
SERIAL NUMBER: ___________________________
DATE OF PURCHASE: _______________________
Spark Plug:
Gap:
Champion 694385
0.030" (0,762 mm)
THEMODELANDSERIALNUMBERSWILLBEFOUND
ONADECALATTACHEDTOTHEREAROFTHESNOW
THROWER HOUSING.
CUSTOMER RESPONSIBILITIES
•
•
Read and observe the safety rules.
Follow a regular schedule in maintaining, caring for
and using your snow thrower.
YOUSHOULDRECORDBOTHSERIALNUMBERAND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
•
Follow the instructions under “Maintenance” and “Stor-
age” sections of this owner’s manual.
TABLE OF CONTENTS
SAFETY RULES ........................................................ 2-3
MAINTENANCE..................................................... 14-15
SERVICE AND ADJUSTMENTS........................... 16-18
STORAGE................................................................... 19
TROUBLESHOOTING................................................ 20
WARRANTY............................................ BACK COVER
PRODUCT SPECIFICATIONS...................................... 3
CUSTOMER RESPONSIBILITIES................................ 3
ASSEMBLY / PRE-OPERATION ............................... 5-7
OPERATION ............................................................ 8-13
MAINTENANCE SCHEDULE ..................................... 14
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS PACKED SEPARATELY IN CARTON
(1) FUEL STABILIZER PACKET
(1) MULTI-
WRENCH
(180684)
(1) POWER CORD
(198563)
SAFTEY IGNITION KEY (S)
(193071)
(1) AUGER CONTROL ROD
(1) DISCHARGE CHUTE
EXTRA SHEAR BOLTS AND NUTS
(6) SHOULDER
BOLT 1/4-20 x 1-3/4
(192090)
(6) LOCKNUTS
1/4-20
(73800400)
ROTATOR HEAD MOUNTING
(3) RETAINER
SPRINGS
(169675)
(1) WASHER 3/8
(19131316)
(1) LOCKNUT 3/8
(73800600)
CHUTE DEFLECTOR REMOTE CONTROL
(1) LOCKNUT (1) CARRIAGE BOLT
(1) LOCKNUT
1/4-20
(191730)
(1) NYLON
WASHER
(179246)
(1) SHOULDER
BOLT 1/4-20
(179829)
(1) SPRING
(184505)
5/16-18
5/16-18 x 5/8
(72250505)
(751153)
(2) CARRIAGE BOLTS
3/8-16 x 2.25
(2) FLAT WASHERS
(2) HANDLE KNOBS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY / PRE-OPERATION
Read these instructions and this manual in its entirety before you attempt to assemble or operate your new
snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly,
operation and maintenance of the product.
Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for shipping
purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts
bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened
securely. Use the correct tools as necessary to ensure proper tightness.
REMOVE SNOW THROWER FROM CARTON
SPEED
CONTROL
ROD
1. Remove all accessible loose parts and parts boxes
from carton.
2. Cut down all four corners of carton and lay panels flat.
3. Removethetwo(2)screwssecuringtheaugerhousing
to the pallet.
4. Removeallpackingmaterialsexceptplastictieholding
speed control rod to lower handle.
PLASTIC TIE
UPPER
HANDLE
5. Remove the two (2) plastic ties securing the upper
handle to the pallet.
6. Remove snow thrower from carton and check carton
thoroughly for additional loose parts.
HANDLE
KNOB
LOWER
HANDLE
HOW TO SET UP YOUR SNOW THROWER
TOOL BOX (See Fig. 10)
A toolbox is provided on your snow thrower. The toolbox is
located on top of the belt cover. Store the extra shear bolts,
nuts and multi-wrench provided in parts bag in the toolbox.
NOTE: The multi-wrench may be used for assembly of the
chuterotatorheadtosnowthrowerandmakingadjustments
to the skid plates.
UNFOLD UPPER HANDLE
1. Raise upper handle to the operating position and
tighten handle knobs securely. Additional carriage
bolts, washers and handle knobs are in bag of parts.
Use to secure upper handle to lower handle. Install
in lower holes in handles.
FIG. 1
SPEED CONTROL ROD
RETAINER
SPRING
INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)
1. Remove plastic tie securing rod to lower handle.
2. Insert rod into speed control bracket and secure with
retainer spring.
SPEED
CONTROL
BRACKET
SPEED
CONTROL
LEVER
FIG. 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY / PRE-OPERATION
INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)
INSTALL TRACTION DRIVE CONTROL ROD
(See Figs. 3 and 4)
The traction drive control rod is installed on the snow
thrower.
1. Retrieve vinyl sleeve and spring from bag of parts and
retrieve the auger control rod from carton chute tray.
Slide straight rod end through the small hole in the
vinyl sleeve. Hook spring in hole in rod end.
2. Hook end of spring into control arm with loop opening
up as shown. (See Fig. 5)
3. With top end of rod positioned under right side of
control panel, push down on rod and insert end of rod
intoholeinaugercontrolbracket. Securewithretainer
spring.
1. Remove plastic tie securing rod to lower handle.
2. With top end of rod positioned under left side of control
panel, pushroddownandinserttopendofrodintohole
in drive control bracket. Secure with retainer spring.
PLASTIC TIE
TRACTION DRIVE
CONTROL ROD
AUGER
CONTROL
ROD
VINYL
SLEEVE
VINYL
SLEEVE
CONTROL
ARM
LOOP
OPENING
UP
FIG. 3
FIG. 5
TRACTION DRIVE
CONTROL LEVER
RETAINER
SPRING
AUGER CONTROL ROD
AUGER
CONTROL
LEVER
RETAINER
SPRING
TRACTION
DRIVE
CONTROL
ROD
DRIVE
CONTROL
BRACKET
AUGER
CONTROL
BRACKET
FIG. 4
FIG. 6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY / PRE-OPERATION
INSTALL DISCHARGE CHUTE / CHUTE ROTATOR
HEAD (See Fig. 7)
INSTALL CHUTE DEFLECTOR REMOTE CONTROL
(See Figs. 8 and 9)
1. Install remote cable bracket to discharge chute with
5/16-18 carriage bolt and 5/16-18 locknut as shown.
Tighten securely.
2. Install remote cable eyelet to chute deflector with
1/4-20 shoulder bolt and 1/4-20 locknut as shown.
Tighten nut securely. Eyelet will be loose on shoulder
bolt.
NOTE: The multi-wrench provided in your parts bag may
be used to install the chute rotator head.
1. Place discharge chute assembly on top of chute base
with discharge opening toward front of snow thrower.
2. Positionchuterotatorheadoverchutebracket. Ifneces-
sary,rotatechuteassemblytoalignsquareandpinonun-
dersideofchuterotatorheadwithholesinchutebracket.
3. With chute rotator head and chute bracket aligned,
position chute rotator head on pin and threaded stud
of mounting bracket.
4. Install 3/8 washer and locknut on threaded stud and
tighten securely.
3. Install spring hooks between hex nuts on chute rotater
head and into hole in chute deflector as shown.
SPRING
1/4-20
CHUTE
SHOULDER
DEFLECTOR
BOLT
HOOK
BETWEEN
HEX NUTS
ON CHUTE
ROTATER
HEAD
CHUTE
ROTATOR
HEAD
3/8 LOCKNUT
3/8 WASHER
1/4-20
LOCKNUT
5/16-18
CARRIAGE
BOLT
CABLE
EYELET
REMOTE
CABLE
BRACKET
PIN
THREADED
STUD
5/16-18
LOCKNUT
FIG. 8
ROTATOR HEAD
MOUNTING
ALIGN BEFORE
TIGHTENING LOCKNUT
CHUTE
BRACKET
BRACKET
FIG. 7
CHUTE DEFLECTOR
CONTROL LEVER
FIG. 9
CHECK TIRE PRESSURE
Thetiresonyoursnowthrowerwereoverinflatedatthefac-
tory for shipping purposes. Correct and equal tire pressure
is important for best snow throwing performance.
•
Reduce tire pressure to 14-17 PSI.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KNOW YOUR SNOW THROWER
READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare
the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save
this manual for future reference.
These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand
their meaning.
PRIMER
DANGER
OR WARNING
READ AND FOLLOW ALL SAFETY INFORMATION
AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
FORWARD REVERSE
IGNITION KEY.
INSERT TO START
AND RUN,
PULL OUT TO STOP.
DISENGAGED
ENGAGED
SNOW
TRACTION
DISCHARGE
DRIVE CONTROL
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
GASOLINE
ELECTRIC
START
AUGER
DISCHARGE CHUTE CONTROL LEVER
FILLER CAP
CONTROL
LEVER
BUTTON
TRACTION
DEFLECTOR
REMOTE
CONTROL
LEVER
DRIVE SPEED
CONTROL LEVER
DRIVE
CONTROL
LEVER
MUFFLER
RECOIL
(AUXILIARY)
STARTER
HANDLE
CHUTE
DEFLECTOR
CHOKE
CON-
TROL
LH TURN
TRIGGER
PRIMER
SAFETY
IGNITION
KEY
DISCHARGE
CHUTE
FUEL
SHUT-OFF
VALVE
THROTTLE
/ ENGINE
CONTROL
LIGHT
HANDLE
KNOB
CLEAN-OUT TOOL
NOTE: ITEMS ABOVE
ARE SHOWN IN
MUFFLER
TOOLBOX
THEIR TYPICAL
LOCATION ON THE
ENGINE. ACTUAL
LOCATION MAY VARY
WITH THE ENGINE
ON YOUR UNIT.
FREEWHEEL
CONTROL
DRIFT
CUTTER
SKID PLATE
AUGERS
FIG. 10
MEETS A.N.S.I. SAFETY REQUIREMENTS
Our snow throwers conform to the standards of the American National Standards Institute.
Toolbox - used to store spare shear bolts, locknuts and
wrench.
Drive speed control lever - used to select forward or
reverse motion and speed of snow thrower.
Freewheel control– disengages transmission for pushing
the snowthrower with the engine off.
Traction drive control lever - used to engage power-pro-
pelled forward or reverse motion of snow thrower.
Safety ignition key - must be inserted for the engine to
start and run. Remove when snow thrower is not in use.
Auger control lever - used to engage auger motion (throw
snow).
Electric start button - used for starting the engine.
Dischargechutecontrollever-usedtochangethedirec-
tion the snow is thrown.
Recoil(auxiliary)starterhandle-usedforstartingengine.
Deflector remote control lever - used to change the
distance the snow is thrown.
Primer - pumps additional fuel from the carburetor to the
cylinder for use when starting a cold engine.
Skid plate - used to adjust height of scraper bar from the
ground.
Choke Control - used for starting a cold engine.
Throttle/engine control - used to select either FAST or
SLOW engine speed and to STOP the engine.
Drift cutter - used to cut through deep snowdrifts.
9
LH and RH turn triggers - used to steer the snow thrower.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
The operation of any snow thrower can result
in foreign objects thrown into the eyes, which
canresultinsevereeyedamage. Alwayswear
safety glasses or eye shields while operating
your snow thrower or performing any adjust-
ments or repairs. We recommend standard safety glasses
or a wide vision safety mask worn over spectacles.
HOW TO USE YOUR SNOW THROWER
OFF
FULL
Know how to operate all controls before adding fuel or
attempting to start the engine.
STOPPING
TRACTION DRIVE
FIG. 13
TO CONTROL SNOW DISCHARGE (See Fig. 14)
•
Release traction drive control lever to stop the forward
WARNING: Snow throwers have ex-
posed rotating parts, which can cause
severe injury from contact, or from ma-
terial thrown from the discharge chute.
Keep the area of operation clear of all
persons, small children and pets at all
times including startup.
or reverse movement of the snow thrower.
AUGER
•
ENGINE
Release the auger control lever to stop throwing snow.
1. Move throttle control to “STOP” position.
2. Remove (do not turn) safety ignition key to prevent
unauthorized use.
NOTE: Never use choke to stop engine.
WARNING:Ifthedischargechuteorau-
ger become clogged, shut-off engine
andwaitforallmovingpartstostop.Use
the clean-out tool, NOT YOUR HANDS,
to unclog the chute and/or auger.
TO USE FUEL SHUT-OFF VALVE (See Fig. 11)
The fuel shut-off valve is located beneath the fuel tank on
the engine. Always operate the snow thrower with the fuel
shut-off valve in the OPEN position.
TheDIRECTIONinwhichsnowistobethrowniscontrolled
by the discharge chute control lever.
•
Tochangethedischargechuteposition,pressdownward
on discharge chute control lever and move lever left
or right until chute is in desired position. Be sure lever
springs back and locks into desired position.
OPEN
The DISTANCE that snow is thrown is controlled by the
position of the chute deflector. Set the deflector low to
throw snow a short distance; set the deflector higher to
throw snow farther.
•
Press downward on chute deflector control lever and
moveleverforwardtolowerthedeflectoranddecrease
the distance. Move lever back to raise the deflector
and increase the distance. Be sure lever springs back
and locks into desired position.
OFF
FIG. 11
TO USE THROTTLE CONTROL (See Fig. 12)
Thethrottlecontrolislocatedontheengine.Alwaysoperate
the snow thrower with the engine at full throttle. Full throttle
offers the best snow thrower performance.
DISCHARGE CHUTE
CONTROL LEVER
CHUTE DEFLECTOR
REMOTE CONTROL LEVER
SLOW
FAST
FIG. 14
FIG. 12
TO THROW SNOW (See Fig. 15)
TO USE CHOKE CONTROL (See Fig. 13)
The auger rotation is controlled by the auger control lever
located on the right side handle.
The choke control is located on the engine. Use the choke
control whenever you are starting a cold engine. Do not
use to start a warm engine.
•
Squeeze auger control lever to handle to engage the
auger and throw snow.
•
To engage choke, turn knob counterclockwise. Slowly
turn knob clockwise to disengage.
•
Release the auger control lever to stop throwing snow.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SPEED and DIRECTION are controlled by the drive speed
control lever.
AUGER
CONTROL
LEVER
•
Move speed control lever to desired position AFTER
engaging the traction drive control lever.
CAUTION: Do not move speed control lever
unless engine is running. Damage to the snow
thrower can result.
•
Slower speeds are for heavier snow and faster speeds
are for light snow and transporting the snow thrower. It
is recommended that you use a slower speed until you
are familiar with the operation of the snow thrower.
FIG. 15
USING THE CLEAN-OUT TOOL (See Fig. 16)
In certain snow conditions, the discharge chute may be-
come clogged with ice and snow. Use the clean-out tool
to dislodge this blockage.
NOTE: When both traction drive and auger control levers
are engaged, the traction drive control lever will lock the
auger control lever in the engaged position. This will allow
you to release your right hand from the handle and adjust
the discharge chute direction without interrupting the snow
throwing process.
When cleaning, repairing, or inspecting, make
certain all controls are disengaged and the au-
ger/impellerandallmovingpartshavestopped.
Disconnect the spark plug wire and keep the
wire away from the spark plug to prevent ac-
cidental starting.
TRACTION DRIVE
CONTROL LEVER
DRIVE SPEED
CONTROL LEVER
•
•
Releasetheaugercontrolleverandshutofftheengine.
Removetheclean-outtoolfromit'smountingclip. Grasp
the tool firmly by the handle and push and twist the tool
into the discharge chute to dislodge the blockage.
Afterthepackedsnowhasbeendislodged,returntheclean-
out tool to it's mounting clip by pushing it into the clip.
•
Makesurethedischargechuteispointedinasafedirec-
tion(novehicles,buildings,people,orotherobjectsare
in the direction of discharge) before restarting engine.
FIG. 17
POWER STEERING OPERATION (See Fig. 18)
•
Restart the engine, then squeeze the auger control
lever to the handle to clear snow from the auger hous-
ing and the discharge chute.
Steering triggers are used to assist in steering your snow
thrower. The triggers are located on the underside of each
handle. Whenatriggerissqueezed, itdisengagesthedrive
wheel on that side of snow thrower and allows it to turn in
that direction.
DISCHARGE CHUTE
•
•
To turn left – squeeze left side trigger.
To turn right – squeeze right side trigger.
LH TURN
TRIGGER
RH TURN
TRIGGER
CLEAN-OUT
TOOL
MOUNTING
CLIP
FIG. 18
TO ADJUST SKID PLATES (See Fig. 19)
NOTE: The wrench provided in your parts bag may be
used to adjust the skid plates.
FIG. 16
TO MOVE FORWARD AND BACKWARD (See Fig. 17)
Skidplatesarelocatedoneachsideoftheaugerhousingand
adjusttheclearancebetweenthescraperbarandtheground
surface.Adjustskidplatesevenlytoproperheightforcurrent
surfaceconditions.Forremovalofsnowinnormalconditions,
such as a paved driveway or sidewalk, place skid plates
in the highest position (lowest scraper clearance) to give
a 1/8" clearance between the scraper bar and the ground.
Useamiddlepositionifthesurfacetobeclearedisuneven.
SELF-PROPELLING, forward and reverse movement of
the snow thrower, is controlled by the traction drive control
lever located on the left side handle.
•
Squeezetractiondrivecontrollevertohandletoengage
the drive system.
•
Release traction drive control lever to stop the forward
or reverse movement of the snow thrower.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
NOTE: It is not recommended to operate the snow thrower
overgravelorrockysurfaces.Objectssuchasgravel,rocks
or other debris, can easily be picked up and thrown by the
impeller, which can cause serious personal injury, property
damage or damage to the snow thrower.
•
If snow thrower must be operated over gravel surface,
use extra caution and be sure skid plates are adjusted
to lowest (highest scraper clearance) position.
1. Shut off engine and wait for all moving parts to stop.
FREEWHEEL POSITION
TRANSMISSION ENGAGED
FIG. 21
2. Adjust skid plates by loosening the 1/2" hex nuts, then
moving skid plate to desired position. Be sure both
plates are adjusted evenly. Tighten securely.
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL (See Fig. 22)
SCRAPER BAR (See Fig. 19)
The engine on your snow thrower has been shipped from
the factory already filled with oil.
1. Check engine oil with snow thrower on level ground.
2. Remove oil fill cap/dipstick and wipe clean, reinsert
the dipstick and screw tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
The scraper bar is not adjustable, but is reversible. After
considerable use it may become worn. When it has worn
almost to the edge of the housing, it can be reversed,
providing additional service before requiring replacement.
Replace a damaged or worn scraper bar.
HIGH POSITION
(LOW GROUND
CLEARANCE)
HEX
NUTS
•
To change engine oil, see “TO CHANGE ENGINE OIL”
in the Maintenance section of this manual.
AUGER
HOUSING
CHOKE
CONTROL
GASOLINE
FILLER CAP
ENGINE OIL
FILL CAP / DIPSTICK
LOW POSITION
(HIGH GROUND
CLEARANCE)
SCRAPER
BAR
FUEL SHUT-
OFF VALVE
SKID PLATE
STARTER
BUTTON
FIG. 19
TO USE DRIFT CUTTERS (See Fig. 20)
Use the drift cutters to cut through deep snowdrifts that are
higher than the front of the snow thrower.
•
Loosen adjustment nuts enough to allow drift cutter to
be raised to highest position and tighten nuts securely.
Repeat for opposite side of snow thrower.
•
When not using drift cutters, loosen adjustment nuts,
lower to storage position and tighten nuts securely.
PRIMER
RECOIL
STARTER
HANDLE
SAFETY
IGNITION
KEY
AUGER
HOUSING
THROTTLE
STORAGE
POSITION
NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
DRIFT
CUTTER
FIG. 22
ADD GASOLINE (See Fig. 22)
ADJUST-
MENT NUTS
•
Fill fuel tank to bottom of tank filler neck. Do not over-
fill. Use fresh, clean, regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
FIG. 20
TO TRANSPORT (See Fig. 21)
When pushing or towing your snowthrower, be sure to
disengage transmission by placing freewheel control into
FREEWHEEL position. Freewheel control is located at the
rear of snowthrower.
WARNING: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
•
•
Pull freewheel control out to FREEWHEEL position.
To reengage transmission, push control back in.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
2. Place throttle control in “FAST” position.
3. Rotate choke control to “FULL” position.
CAUTION: Alcohol blended fuels (called gaso-
hol or using ethanol or methanol) can attract
moisture which leads to separation and forma-
tion of acids during storage. Acidic gas can
damage the fuel system of an engine while in
storage. To avoid engine problems, the fuel
system should be emptied before storage of
30 days or longer. Drain the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. SeeStorageInstructionsforadditional
information. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
4. Push the primer four (4) times if the temperature is
below 15°F, or two (2) times if temperature is between
15° and 50°F. If temperature is above 50°F, priming is
not necessary.
NOTE: Over priming may cause flooding, preventing the
engine from starting. If you do flood the engine, wait a
few minutes before attempting to start and DO NOT push
the primer.
5. Pull recoil starter handle quickly. Do not allow starter
rope to snap back.
6. Whentheenginestarts,releasetherecoilstarterhandle
and slowly move the choke control to the “OFF” posi-
tion.
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operat-
ing temperature.
WARM START - RECOIL STARTER
Follow the steps above, keeping the choke in the “OFF”
position. DO NOT push the primer.
TO START ENGINE
•
Be sure fuel shut-off valve is in the “OPEN” position.
Your snow thrower engine is equipped with both a 120 Volt
A.C. electric starter and a recoil starter. The electric starter
is equipped with a three-wire power cord and plug and is
designed to operate on 120 Volt A.C. household current.
•
Be sure your house is a 120 Volt A.C. three-wire
grounded system. If you are uncertain, consult a
licensed electrician.
BEFORE STOPPING
Run the engine for a few minutes to help dry off any mois-
ture on the engine.
IF RECOIL STARTER HAS FROZEN
If the recoil starter has frozen and will not turn the engine,
proceed as follows:
1. Grasp the recoil starter handle and slowly pull as much
rope out of the starter as possible.
WARNING: Do not use the electric
starter if your house is not a 120 Volt
A.C.three-wiregroundedsystem. Seri-
ous personal injury or damage to your
snow thrower could result.
COLD START - ELECTRIC STARTER
2. Release the recoil starter handle and let it snap back
against the starter.
If the engine still fails to start, repeat the above steps or
use the electric starter.
1. Insert safety ignition key (tied to recoil start cord) into
ignition slot until it clicks. DO NOT turn the key. Keep
the extra safety ignition key in a safe place.
2. Place throttle control in “FAST” position.
3. Rotate choke control to “FULL” position.
4. Connect the power cord to the engine.
5. Plug the other end of the power cord into a three-hole
grounded 120 Volt A.C. receptacle.
NOTE: Do not use primer when starting engine with the
electric starter.
SNOW THROWING TIPS
•
•
•
•
Always operate the snow thrower with the engine at
full throttle. Full throttle offers the best performance.
Goslowerindeep,freezingorheavywetsnow.Usethe
drive speed control, NOT the throttle, to adjust speed.
It is easier and more efficient to remove snow imme-
diately after it falls.
The best time to remove snow is the early morning. At
this time the snow is usually dry and has not been ex-
posed to the direct sun and warming temperatures.
6. Push starter button until engine starts.
IMPORTANT: Do not crank engine more than five continu-
ous seconds between each time you try to start. Wait 5 to
10 seconds between each attempt.
7. When the engine starts, release the starter button and
slowly move the choke control to the “OFF” position.
8. Disconnect the power cord from the receptacle first,
then from the engine.
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operat-
ing temperature.
•
Slightly overlap each successive path to ensure all
snow will be removed.
•
•
Throw snow downwind whenever possible.
Adjust the skid plates to proper height for current snow
conditions. See “TO ADJUST SKID PLATES” in this
section of this manual.
•
For extremely heavy snow, reduce the width of snow
removal by overlapping previous path and moving
slowly.
WARM START - ELECTRIC STARTER
Follow the steps above, keeping the choke control in the
“OFF” position.
COLD START - RECOIL STARTER
1. Insert safety ignition key (tied to recoil start cord) into
ignition slot until it clicks. DO NOT turn the key. Keep
the extra safety ignition key in a safe place.
•
•
•
Keep engine clean and clear of snow during use. This
will help air flow and extend engine life.
Aftersnow-throwingiscompleted,allowenginetorunfor
a few minutes to melt snow and ice off the engine.
Clean the entire snow thrower thoroughly after each
use and wipe dry so it is ready for next use.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow
during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the
snow thrower.
MAINTENANCE
LUBRICATION CHART
GENERAL RECOMMENDATIONS
The warranty on this snow thrower does not cover items
that have been subjected to operator abuse or negligence.
To receive full value from the warranty, operator must
maintain snow thrower as instructed in this manual. Some
adjustments will need to be made periodically to properly
maintain your snow thrower.
➀ SAE 30 Motor Oil
See “ENGINE” in
➁
Maintenance section
General
Purpose
Grease
➂
All adjustments in the Service and Adjustments section of
this manual should be checked at least once each season.
•
Once a year, you should replace the spark plug and
check belts for wear. A new spark plug will help your
engine run better and last longer.
➀ Pivot points
•
Follow the maintenance schedule in this manual.
NOTE: Use only Original Equipment Manufacturer (OEM)
parts to service this unit. Failure to do so can cause the unit
to malfunction and pose a risk of injury to the operator.
BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
3. Checkcontrolstobesuretheyarefunctioningproperly.
➁
Engine
oil
LUBRICATION
Keep your snow thrower well lubricated
(See “LUBRICATION CHART”).
➂ Auger
grease fittings
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Checkthecrankcaseoillevelbeforestartingtheengineand
SNOW THROWER
after each five (5) hours of continuous use. Tighten oil fill
cap / dipstick securely each time you check the oil level.
Alwaysobservesafetyruleswhenperformingmaintenance.
TIRES
•
•
TO CHANGE ENGINE OIL
Determine temperature range anticipated before next oil
change.AlloilmustmeetAPIserviceclassificationSG–SL.
Maintain proper air pressure in both tires (14–17 PSI).
Keep tires free of gasoline / oil, which can harm rubber.
NOTE:Tosealtirepuncturesandpreventflattiresduetoslow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and corrosion.
•
•
•
Be sure snow thrower is on level surface.
Oil will drain more freely when warm.
Catch oil in a suitable container.
BELTS
NOTE: The left side wheel may be removed from snow
thrower for easier access to the oil drain plug and place-
ment of a suitable container. The unit tilted, resting on the
frame with the left wheel removed, will help drain any oil
trapped inside the engine. (See “TO REMOVE WHEELS”
in the Service and Adjustments section of this manual).
Check belts for deterioration and wear after every 50 hours
of operation and replace if necessary. The belts are not
adjustable. Replace belts if they begin to slip from wear.
(See “TO REMOVE BELT COVER” in the Service and
Adjustments section of this manual).
The belts on your snow thrower are of special construction
andshouldbereplacedbyoriginalequipmentmanufacturer
(OEM)beltsavailablefromyournearestdealer.Usingother
than OEM belts can cause personal injury or damage to
the snow thrower.
1. Remove safety ignition key and disconnect spark plug
wire from spark plug. Place wire where it cannot come
in contact with spark plug.
2. Clean area around drain plug.
3. Remove drain plug and drain oil in a suitable container.
4. Install drain plug and tighten securely.
AUGER GEAR CASE
•
Thegearcasewasfilledwithlubricanttotheproperlevel
at the factory. The only time the lubricant needs atten-
tion is if service has been performed on the gear case.
5. Wipe off any spilled oil from snow thrower and engine.
6. Install left wheel (if removed for draining oil). Be sure to
install klik pin into proper hole in wheel axle (See “TO
REMOVE WHEELS” in the Service and Adjustments
section of this manual).
7. Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine.
8. Refill engine with oil through oil dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCTSPECIFICATIONS”sectionofthismanual.
9. Use gauge on oil fill cap/dipstick for checking level.
Be sure dipstick cap is tightened securely for accurate
reading. Keep oil at “FULL” line on dipstick.
•
If lubricant is required, use only Ronex ED #1 grease.
TRACTION DRIVE SYSTEM
DO NOT lubricate the drive components inside the snow
thrower. The sprockets, hex shafts, drive disc and friction
wheel require no lubrication. The bearings and bushings
are lifetime lubricated and require no maintenance.
CAUTION:Anylubricatingoftheabovecompo-
nents can cause contamination of the friction
wheel and damage to the drive system of your
snow thrower.
10. Wipe off any spilled oil.
MUFFLER
Inspect and replace corroded muffler as it could create a
fire hazard and/or damage.
SPARK PLUG
Replacesparkplugatthebeginningofeachseasonorafter
every100hoursofoperation,whicheveroccursfirst. Spark
plug type and gap setting are shown in the “PRODUCT
SPECIFICATIONS” section of this manual.
ENGINE
See engine manual.
LUBRICATION
Use only high quality detergent oil rated with API service
classification SG–SL. Select the oil's SAE viscosity grade
according to your expected operating temperature.
CLEANING
IMPORTANT: For best performance, keep snow thrower
housing free of any dirt or trash. Clean the outside of your
snow thrower after each use.
WARNING: Removesafetyignitionkey
and disconnect spark plug wire from
spark plug. Place wire where it cannot
come in contact with spark plug.
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
possible engine damage from running low on oil.
•
•
Keepfinishedsurfaces/wheelsfreeofgasoline,oil,etc.
We do not recommend using a garden hose to clean
yoursnowthrowerunlesstheelectricalsystem,muffler
and carburetor are covered to keep water out. Water
in engine can result in shortened engine life.
Change the oil after every 25 hours of operation or at least
once a year if thrower is not used for 25 hours in one year.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
To replace the capscrew/shear bolts:
1. Disengage all controls and move throttle control to
STOP position. Wait for all moving parts to stop.
2. Remove safety ignition key and disconnect spark plug
wire from spark plug. Place wire where it cannot come
in contact with spark plug.
3. Align holes in impeller hub with holes in impeller shaft
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear
bolts. Install 1/4-20 locknuts and tighten securely.
WARNING: To avoid serious injury, before per-
forming any service or adjustments:
1. Be sure throttle is in STOP position.
2. Remove safety ignition key.
3. Make sure the augers and all moving
parts have completely stopped.
4. Disconnect spark plug wire from
spark plug and place wire where it
cannot come in contact with plug.
CAUTION: Do not substitute. Use only original
equipment capscrew/shear bolts as supplied
with your snow thrower.
SNOW THROWER
TO ADJUST SNOW THROWER HEIGHT
See “TO ADJUST SKID PLATES” and “SCRAPER BAR”
in the Operation section of this manual.
4. Insertsafetyignitionkeyandreconnectsparkplugwire
to spark plug.
1/4-20 x 1-5/8
CAPSCREW /
SHEAR BOLT
1/4-20 x 2
SHOULDER /
SHEAR BOLT
CHUTE DEFLECTOR
The chute deflector, attached to the top of the discharge
chute, is provided to direct discharging snow away from
the operator. If the deflector becomes damaged, it should
be replaced.
IMPELLER
HUB
1/4-20
LOCKNUT
WARNING: To avoid serious injury,
never operate your snow thrower with
the deflector removed or damaged.
AUGER HUB
•
Tochangedirectionand/ordistancesnowisdischarged,
see “TO CONTROL SNOW DISCHARGE” in the Op-
eration section of this manual.
1/4-20 LOCKNUT
AUGER
SHAFT
SHEAR BOLTS (See Fig. 23)
AUGER SHEAR BOLTS
IMPELLER
SHAFT
Both right and left-hand augers are secured to the auger
shaft with a shear bolt and hex nut. Should a foreign ob-
ject or ice become lodged in the augers, the shear bolts
are designed to break, preventing damage to any other
components. If one or both augers do not turn when auger
control lever is engaged, check to see if one or both of the
bolts have sheared. To replace the shear bolts:
FIG. 23
TO REMOVE BELT COVER (See Fig. 24)
1. Remove two (2) screws securing belt cover to frame.
2. Remove belt cover.
1. Disengage all controls and move throttle control to
STOP position. Wait for all moving parts to stop.
•
Replace belt cover by installing cover and screws and
tighten securely.
2. Remove safety ignition key and disconnect spark plug
wire from spark plug. Place wire where it cannot come
in contact with spark plug.
BELT
COVER
3. Align hole in auger hub with hole in auger shaft and
install a new 1/4-20 x 2" shear bolt. Install 1/4-20
lock nut and tighten securely.
CAUTION: Do not substitute. Use only original
equipment shear bolts as supplied with your
snow thrower.
4. Insertsafetyignitionkeyandreconnectsparkplugwire
to spark plug.
IMPELLER SHEAR BOLTS
FRAME
SCREWS
The impeller is secured to the impeller shaft with two (2)
capscrew/shearboltsandhexnuts. Shouldaforeignobject
or ice become lodged in the impeller, the capscrews are
designed to break, preventing damage to any other com-
ponents. If impeller does not turn when auger control lever
is engaged, check to see if the capscrews have sheared.
FIG. 24
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
TO REPLACE BELTS (See Fig. 25)
7. RELIEVE TENSION ON TRACTION DRIVE BELT
IDLER and remove traction drive belt from around
pulleys.
The auger and traction drive belts are not adjustable. If the
belts are damaged or begin to slip from wear, they should
be replaced. It is recommended that the belt(s) be replaced
by a service center/department.
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into
the square hole in idler arm and rotate ratchet clockwise
to relieve tension.
8. With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
9. Placeaugerbeltaroundandinsidethegrooveofauger
pulley only.
10. While your assistant slowly raises handles to rejoin
the auger housing and frame assembly, pull up on the
auger belt and squeeze sides together above pulley
so belt is fully seated in groove of pulley.
11. Move idler arm so it does not hit impeller pulley as you
bring snow thrower completely together and check
carefully for proper routing of belts. If auger belt has
becomedislodgedfromthepulley(bycatchingtheidler
arm bracket while bringing snow thrower together),
separate the snow thrower and repeat step 12. Belt
must be fully seated in pulley groove when bringing
the snow thrower together.
NOTE: It is recommended that both the auger and traction
drive belt be replaced at the same time.
The V-belts on your snow thrower are of special construc-
tion and should be replaced by original equipment manu-
facturer (OEM) belts available from your nearest service
center/department. Using other than OEM belts can cause
personal injury or damage to the snow thrower.
WARNING: Belt replacement requires
separation of the snow thrower. While
separating the auger housing from the
frame assembly, it is important that
an assistant stand in the operating
position and hold the snow thrower
handles. Serious personal injury and/
or damage to the unit could occur if the
snowthrowershouldfallduringthebelt
changing process.
12. Install the two (2) hex bolts and tighten securely.
FRAME
ASSEMBLY
AUGER
HOUSING
13. INSTALLENGINEPULLEY-Placebeltinpulleygroove
and slide pulley on crankshaft. Install flat washer, bolt
and tighten securely (41-47 N-m torque). Make sure
belt is inside belt keeper.
14. INSTALL BELT COVER and two (2) screws. Tighten
securely.
15. INSTALL DISCHARGE CHUTE – See “INSTALL DIS-
CHARGE CHUTE / CHUTE ROTATER HEAD” in the
Assembly / Pre-Operation section of this manual.
HANDLES
BELT KEEPER
TRACTION DRIVE BELT
ENGINE
1. REMOVE GASOLINE FROM FUEL TANK - Drain
gasoline from fuel tank into a suitable container, out-
doors, away from fire or flame. Wipe up any spilled
gasoline.
FLAT WASHER
PULLEY
2. REMOVE DISCHARGE CHUTE - Loosen locknut
securing chute rotator head to mounting bracket only
enough to allow chute rotator head to be raised and
discharge chute to be removed from snow thrower.
3. REMOVE BELT COVER - See “TO REMOVE BELT
COVER” in this section of this manual.
BOLT
AUGER
BELT
IDLER ARM
SQUARE
HOLE
4. REMOVEENGINEPULLEY-Removebolt,flatwasher
securing pulley to engine crankshaft. Remove outside
(auger) pulley only from crankshaft.
CLUTCHING
IDLER ARM
BRACKET
5. SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
remove the two (2) bolts holding auger housing and
frame together.
AUGER
HOUSING
FRAME
AUGER PULLEY
BOLTS
WARNING: As the last bolt is removed,
have your assistant carefully lower the
handles down to the ground.
6. REMOVE AUGER BELT from around pulley.
FIG. 25
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
TO REMOVE WHEELS (See Fig. 26)
Remove the klik pin and remove wheel from axle.
ENGINE SPEED
Never tamper with the engine governor, which is factory set
for proper engine speed. Overspeeding the engine above
the factory high speed setting can be dangerous and will
void the warranty. If you think the engine-governed high
speed needs adjusting, contact a qualified service center,
which has proper equipment and experience to make any
necessary adjustments.
•
IMPORTANT: When installing wheel, be sure to use the
axle hole closest to the end of the shaft – do not use the
hole in the wheel hub (if equipped). Inner hole in axle and
holeinwheelhubarenotusedforyourmodelsnowthrower.
NOTE: To seal punctures or prevent flat tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and corrosion.
TO ADJUST CABLE TENSION (See Fig. 27)
Adjust cable tension by turning the adjuster turn buckle,
located on the right hand cable. Grasp the long section
tightly and turn the short section to lengthen the adjuster.
Adjust until cable is snug.
KLIK PIN (INSTALL
IN OUTER HOLE
OF AXLE ONLY)
OUTER HOLE
ADJUSTER TURN
BUCKLE
AXLE
WHEEL
WHEEL HUB
FIG. 26
ENGINE
See engine manual.
CARBURETOR
Your carburetor is not adjustable. Engine performance
should not be affected at altitudes up to 7,000 feet (2,134
meters). If your engine does not operate properly due to
suspected carburetor problems, take your snow thrower
to a qualified service center.
FIG. 27
18
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
Immediately prepare your snow thrower for storage at
•
•
•
Empty the fuel tank by starting the engine and letting
it run until the fuel lines and carburetor are empty.
the end of the season or if the unit will not be used for 30
days or more.
Never use engine or carburetor cleaner products in
the fuel tank or permanent damage may occur.
Use fresh fuel next season.
WARNING: Never store the snow
throwerwithgasolineinthetankinside
a building where fumes may reach an
open flame, spark or pilot light as on a
furnace, water heater, clothes dryer or
gasappliance. Allowtheenginetocool
before storing in any enclosure.
NOTE: Fuel stabilizer is an acceptable alternative in min-
imizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not drain the
gas tank and carburetor if using fuel stabilizer.
SNOW THROWER
When snow thrower is to be stored for a period of time,
clean it thoroughly, remove all dirt, grease, leaves, etc.
Store in a clean, dry area.
1. Clean entire snow thrower (See “CLEANING” in the
Maintenance section of this manual).
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine
oil. (See “ENGINE” in the Maintenance section of this
manual).
CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through spark plug hole
into cylinder.
3. Pullrecoilstarterhandleslowlyafewtimestodistribute
oil.
4. Replace with new spark plug.
2. Inspect and replace belts, if necessary (See “TO RE-
PLACEBELTS”intheServiceandAdjustmentssection
of this manual).
3. Lubricate as shown in the Maintenance section of this
manual.
4. Besurethatallnuts,bolts,screws,andpinsaresecurely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
5. Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
OTHER
•
•
•
Remove safety ignition key; store it in a safe place.
Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
ENGINE
See engine manual.
•
•
If possible, store your snow thrower indoors and cover
it to protect it from dust and dirt.
Cover your snow thrower with a suitable protective
cover that does not retain moisture. Do not use plastic.
Plastic cannot breathe, which allows condensation to
form and will cause your snow thrower to rust.
FUEL SYSTEM
IMPORTANT: It is important to prevent gum deposits from
forming in essential fuel system parts such as carburetor,
fuel hose, or tank during storage. Also, alcohol blended
fuels (called gasohol or using ethanol or methanol) can
attract moisture which leads to separation and formation
of acids during storage. Acidic gas can damage the fuel
system of an engine while in storage.
IMPORTANT: Never cover snow thrower while engine/ex-
haust area is still warm.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
See appropriate section in manual unless directed to an authorized service center/department.
PROBLEM
CAUSE
CORRECTION
Does not start
1. Fuel shut-off valve (if so
equipped) in OFF position.
2. Safety ignition key
is not inserted.
1. Turn fuel shut-off valve to OPEN position.
2. Insert safety ignition key.
3. Out of fuel.
3. Fill fuel tank with fresh, clean gasoline.
4. Move throttle to FAST position
(or ON/OFF switch to ON position).
5. Move to FULL position.
6. Prime as instructed in the Operation section of this manual.
7. Wait a few minutes before restarting, DO NOT prime.
8. Connect wire to spark plug.
4. Throttle in STOP position
(or ON/OFF switch is OFF).
5. Choke in OFF position.
6. Primer not depressed.
7. Engine is flooded.
8. Spark plug wire is
disconnected.
9. Bad spark plug.
10. Stale fuel.
11. Water in fuel.
9. Replace spark plug.
10. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
11. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
Loss of power
1. Spark plug wire loose.
2. Throwing too much snow.
3. Fuel tank cap is covered
with ice or snow.
1. Reconnect spark plug wire.
2. Reduce speed and width of swath.
3. Remove ice and snow on and around fuel tank cap.
4. Dirty or clogged muffler.
4. Clean or replace muffler.
Engine idles or
runs roughly
1. Choke is in FULL position.
2. Blockage in fuel line.
3. Stale fuel.
4. Water in fuel.
5. Carburetor is in need of
adjustment or overhaul.
1. Move choke to OFF position.
2. Clean fuel line.
3. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
4. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
5. Contact an authorized service center/department.
Excessive
vibration
1. Loose parts or damaged
augers or impeller.
1. Tighten all fasteners. Replace damaged parts. If vibration
remains, contact an authorized service center/department.
Recoil starter
is hard to pull
1. Frozen recoil starter.
1. See “IF RECOIL STARTER HAS FROZEN”
in the Operation section of this manual.
Loss of traction 1. Drive belt is worn.
1. Check / replace drive belt.
2. Check / reinstall drive belt.
drive / slowing
of drive speed
2. Drive belt is off of pulley.
3. Friction drive wheel is worn. 3. Contact an authorized service center/department.
Loss of snow
discharge or
slowing of
1. Auger belt is off of pulley.
2. Auger belt is worn.
3. Clogged discharge chute.
1. Check / reinstall auger belt.
2. Check / replace auger belt.
3. Clean snow chute.
4. Remove debris or foreign object from augers / impeller.
snow discharge 4. Augers / impeller jammed.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Wheeled Products – Limited Warranty
Husqvarna warrants to the original retail purchaser that this Husqvarna® product is free from defects in material or workmanship
under normal use and maintenance from the date of retail purchase for the applicable Warranty Period shown on Exhibit A. Certain
components (e.g., engines and transmissions) are excluded from coverage, and other limitations apply, as described in this document.
Husqvarna will repair or replace at its discretion, any defective product or part covered by the Limited Warranty, free of charge at any
authorized Husqvarna Servicing Dealer/Center using original OEM Husqvarna replacement parts, subject to the limitations and
exclusions described below. Husqvarna does not offer an over-the-counter exchange program.
THIS LIMITED WARRANTY IS THE SOLE EXPRESS WARRANTY PROVIDED BY HUSQVARNA. ANY WARRANTY
THAT MAY BE IMPLIED BY LAW (INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE OR USE AND IMPLIED WARRANTY OF MERCHANTABILITY) IS LIMITED TO THE DURATION OF THE
APPLICABLE WARRANTY PERIOD UNDER THIS LIMITED WARRANTY. THIS LIMITED WARRANTY MAY BE
MODIFIED ONLY BY HUSQVARNA. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
THIS WARRANTY IS GIVEN ONLY BY HUSQVARNA. THE ABOVE REMEDIES ARE THE EXCLUSIVE REMEDIES FOR
ANY BREACH OF THIS LIMITED WARRANTY. HUSQVARNA AND ITS AFFILIATED COMPANIES SHALL NOT BE
LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGE, INCLUDING LOST PROFITS RESULTING
FROM ANY SUCH BREACH, AND ALL SUCH DAMAGES ARE HEREBY DISCLAIMED. SOME STATES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS
MAY NOT APPLY TO YOU.
LIMITATIONS AND EXCLUSIONS
1. Engines, Transmissions and certain other components are NOT covered. This Limited Warranty does not cover any of the
following:
(a) Engines and Attachments. Except where otherwise indicated on Exhibit A, all Engines and Attachments are not covered by
this warranty. In most cases, these items are NOT manufactured by Husqvarna in which case they may be covered separately by
their respective manufacturer’s warranties if one is provided and included with the product at the time of purchase. All such
claims must be submitted and sent to the appropriate manufacturer or as otherwise directed in those separate warranties.
Husqvarna is not authorized to handle warranty adjustments or repairs on engines manufactured by Briggs & Stratton, Honda,
Kawasaki, or Kohler (exception – models equipped with LCT engines). Husqvarna does not assume any warranty obligation of
the other manufacturer’s engines.
(b) Transmissions. Except where otherwise indicated on Exhibit A, Transmission / Transaxle (including Drive Systems) are not
covered by this warranty. In most cases, these items are NOT manufactured by Husqvarna in which case they may be covered
separately by their respective manufacturer’s warranties if one is provided and included with the product at the time of purchase.
The following transmission / transaxle manufacturers, Dana, Hydro-Gear, Tuff-Torq provide a warranty for the transmission /
transaxle to the ultimate purchaser or to Husqvarna. Husqvarna will assign the transmission / transaxle manufacturer’s warranty
or any rights thereof to the original purchaser of the unit. To obtain transmission / transaxle warranty service, first contact the
retailer who you purchased the unit from. Should you require assistance or have any questions concerning transmission / transaxle
Husqvarna service provider. All such claims must be submitted and sent to the appropriate manufacturer or as otherwise directed
in those separate warranties. Husqvarna is not authorized to handle warranty adjustments or repairs on transmissions or transaxles.
Husqvarna does not assume any warranty obligation of the above listed manufacturers (for exceptions – see Exhibit A).
(c) Expendable Parts. This Limited Warranty does not cover general maintenance parts and items (“Expendable Parts”),
including without limitation spark plugs, bulbs, filters, lubricants, starter cords, belts, blades, and blade adapters.
(d) Emissions Control Components. This Limited Warranty does not cover Emissions control equipment and components to the
extent regulated by the U.S. Environmental Protection Agency or similar state agencies. Such equipment and components are
covered by a separate emission control warranty statement supplied with your new product. Please consult this separate warranty
statement for details.
2. Any COMMERCIAL, INSITUTIONAL, AGRICULTURAL, INDUSTRIAL, INCOME PRODUCING, or RENTAL use will result in either No
Warranty or a Shortened Warranty Period Depending on the product; there is either NO WARRANTY or a reduced warranty if the product is used for commercial,
institutional, agricultural, industrial, income producing, or rental purposes. Please refer to Exhibit A.
3. Owner’s (Your) Responsibilities. To preserve your rights under this Limited Warranty, you must demonstrate reasonable care
and use of the product, including, following the preventative maintenance, storage, fuel and oil usages as prescribed in the enclosed
operator’s manual. For example, the following items are the Owner’s responsibility and are not covered by this Limited Warranty:
a. Set-up and pre-delivery service, and engine tune-ups.
b. Adjustments after the first (30) thirty days of purchase and beyond, such as throttle cable, belt guides adjustments.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
c. Preventative maintenance as outlined in the operator’s manual.
In addition, you must cease using the product immediately upon any failure or damage. The product should be taken to an authorized
Husqvarna servicing dealer prior to any further use.
4. Damages resulting from normal aging, wear and tear or neglect are NOT covered. The Limited Warranty does not cover
damage other than that resulting from defects in material or workmanship. The following are NOT considered defects in material or
workmanship, and therefore are NOT covered.
(a) Abrasion to mower decks;
(b) Tires damaged by external punctures;
(c) Natural discoloration of materials due to ultraviolet light;
(d) Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures;
In addition, this Limited Warranty does not cover damages, malfunctions or failures resulting from abuse or neglect of the product
related to or including any of the following:
(e) Failure to provide or perform required maintenance services as prescribed in the operator’s manual;
(f) Abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing, use of unauthorized attachments, Lack of
lubrication or engine failure, due to the use of oils that do not meet Engine manufacturer’s specifications;
(g) Use of gasohol, containing methanol (wood alcohol). Gasohol which contains a maximum 10% ethanol (grain alcohol) or
15% MTBE (methyl/tertiary/butyl/ether) is approved;
(h) Use of ether or any starting fluids;
(i) Pressure cleaning or steam cleaning the product;
(j) Use of spark plugs other than those meeting emission performance requirements listed in the operator’s manual;
(k) Tampering with engine speed governor or emission components, or running engines above specified and recommended
engine speeds as listed in your operator’s manual;
(l) Operation of the unit with improperly installed/removed or modified cutting shields, guards, or safety devices;
(m) Any removed/damaged air filter, excessive dirt, abrasives, salt water, moisture, corrosion, rust, varnish, stale fuel, or any
adverse reaction due to incorrect storage procedures;
(n) Failures due to improper set up, pre-delivery service or repair service by anyone other than an authorized Husqvarna
servicing dealer during the warranty period;
(o) Dirt contaminated grease or oil, use of incorrect type of greases or oils, failure to comply with recommended greasing
intervals, water or moisture damage, and/or improper storage;
(p) Sprayers pumping or spraying caustic or flammable materials, lack of or broken strainers; or
(q) Continued use of product, after initial operational problem or failure occurs.
HOW TO OBTAIN SERVICE
5. Authorized Husqvarna Servicing Dealer/Center. In order to obtain warranty coverage it is your responsibility (at your
expense) to deliver or ship your Husqvarna unit to an authorized Husqvarna Servicing Dealer/Center and arrange for pick-up or return
of your unit after the repairs have been made. If you do not know the location of your nearest authorized Husqvarna Servicing Dealer,
Should you require assistance or have questions concerning this Limited Warranty, you may contact us at 800-487-5951 during the
hours of 8:00 AM to 8:00 PM Eastern Standard Time or contact us through the web at www.husqvarna.com.
6. Documentation Required. You must maintain and present Proof of purchase (including date, product model and, if applicable,
engine serial number) to an authorized Husqvarna Servicing Dealer for warranty service under this Limited Warranty. Proof of
purchase rests solely with the owner-customer.
Husqvarna encourages you to register your product online at
www.usa.husqvarna.com to help ensure, among other things, that you can be notified of important product information. However,
registering your product is not a condition of warranty service.
Husqvarna Consumer Outdoor Products N.A., Inc.; Husqvarna Professional Products, Inc.
9335 Harris Corners Parkway Charlotte, NC 28269
575 49 43-01 R3 2010
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Wheeled Warranty Chart 2010
Exhibit A
Consumer (personal,
Commercial (any commercial,
Rental (any rental
household use only)
professional, institutional,
arigculutral, or income producing
use, other than Rental Use)
usage)
Product/Component
Riding Lawn Tractors:
Frame, Chassis, Front Axle
Engine*
5 Years
*
NO WARRANTY
*
NO WARRANTY
*
Transmission (if made by
Husqvarna/Peerless)
Transmission (if third party)**
Battery
3 Years
**
1 Year Pro-rated
3 Years
NO WARRANTY
**
NO WARRANTY
NO WARRANTY
NO WARRANTY
**
NO WARRANTY
NO WARRANTY
Other Non-Expendable Components
Residential Zero Turn Mowers ( RZ Only )
Engine*
Transmission **
Battery
Other Non-Expendable Components
Residential Zero Turn Mowers ( MZ & EZ )
Engine*
*
**
*
*
NO WARRANTY
NO WARRANTY
NO WARRANTY
NO WARRANTY
NO WARRANTY
NO WARRANTY
1 Year Pro-rated
3 Years
*
**
*
**
*
**
Transmission **
Battery
1 Year Pro-rated
3 Years
1 Year Pro-rated
1 Year
NO WARRANTY
NO WARRANTY
Other Non-Expendable Components
LE475 Edger
Engine*
*
*
*
Other Non-Expendable Components
Walk Behind Mowers
Engine*
2 Years
90 days
90 days
*
*
*
Battery
1 Year Pro-rated
2 Years
NO WARRANTY
NO WARRANTY
NO WARRANTY
NO WARRANTY
Other Non-Expendable Components
Snow Throwers
Engine*
*
*
*
Other Non-Expendable Components
Tillers
2 Years
90 days
90 days
Engine*
Battery
*
1 Year Pro-rated
2 Years
*
*
NO WARRANTY
NO WARRANTY
NO WARRANTY
NO WARRANTY
NO WARRANTY
NO WARRANTY
Other Non-Expendable Components
Tiller Tines
***
Hovering Trimmers
Engine*
*
*
*
Other Non-Expendable Components
2 Years
Consumer
1 Year
Commercial
90 days
Rental
* See Separate Engine Manufacturer's or Manufacturer's warranty
LCT Engines on specific Snow Throwers & Tillers, warranty through Husqvarna.
** See reference 1 (b) of the warranty statement.
RZ - Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network.
EZ - One (1) Year Commercial warranty, parts & labor, with Husqvarna.
Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network.
MZ - Two (2) Year Commercial warranty, parts & labor, with Hydro-Gear Distributor network.
*** "Limited Lifetime Warranty" on Tiller tines is for the life of the product or 7 (seven) years after the last date of the complete
unit's final production, whichever comes first.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Wheeled Warranty Chart 2010
Exhibit A
Consumer (personal,
Commercial (any commercial,
Rental (any rental
household use only)
professional, institutional,
arigculutral, or income producing
use, other than Rental Use)
usage)
Product/Component
Front Mounted Deck Riders
Engine*
*
*
*
Transmission
Battery
Other Non-Expendable Components
2 Years
1 Year Pro-rated
2 Years
NO WARRANTY
NO WARRANTY
NO WARRANTY
NO WARRANTY
NO WARRANTY
NO WARRANTY
Cultivators
Battery
1 Year Pro-rated
2 Years
NO WARRANTY
NO WARRANTY
NO WARRANTY
NO WARRANTY
Other Non-Expendable Components
Pressure Washers
Model 5525PW:
Engine*
*
*
*
Pump
2 Years
2 Years
NO WARRANTY
NO WARRANTY
NO WARRANTY
NO WARRANTY
Other Non-Expendable Components
All other Pressure Washers (6027PW, 9032PW, 1340PW)
Engine*
*
*
*
Pump
2 Years
2 Years
2 Years
2 Years
NO WARRANTY
NO WARRANTY
Other Non-Expendable Components
Generators
Engine*
*
*
*
*2 Years (2nd Year
Parts Only)
*2 Years-1365GN (2nd Year
Parts Only)
Other Non-Expendable Components*
Spreaders
NO WARRANTY
1 Year
Spreader
1 Year
1 Year
Robotic Mowers
Robotic Mower
Battery
2 Years
1 Year
90 days
1 Year
90 days
1 Year
Parts & Accessories (if purchased)
Accessories (e.g., grass catcher, bumper
guard accessories, etc.
Parts (e.g., belts, blades, etc.)
1 Year
30 days
NO WARRANTY
NO WARRANTY
NO WARRANTY
NO WARRANTY
Parts & Accessories (if replaced in Warranty Service)
Replacement parts and/or accessories
provided under this Limited Warranty are
warranted only for the BALANCE of the
warranty period applicable to the part or
accessory that was replaced.
See to left
See to left
See to left
Consumer
Commercial
Rental
* See Separate Engine Manufacturer's or Manufacturer's warranty
LCT Engines on specific Snow Throwers & Tillers, warranty through Husqvarna.
** See reference 1 (b) of the warranty statement.
RZ - Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network.
EZ - One (1) Year Commercial warranty, parts & labor, with Husqvarna.
Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network.
MZ - Two (2) Year Commercial warranty, parts & labor, with Hydro-Gear Distributor network.
*** "Limited Lifetime Warranty" on Tiller tines is for the life of the product or 7 (seven) years after the last date of the complete
unit's final production, whichever comes first.
532 43 58-96 05.19.10 TH
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|