1130SBE
Owner's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Whencleaning,repairingorinspectingthesnowthrower,
stoptheengineandmakecertainthecollector/impeller
and all moving parts have stopped. Disconnect the
spark plug wire and keep the wire away from the plug
to prevent someone from accidentally starting the en-
gine.
Clearing a Clogged Discharge Chute
Handcontactwiththerotatingimpellerinsidethedischarge
chute is the most common cause of injury associated with
snow throwers. Never use your hand to clean out the dis-
charge chute. To clear the chute:
1. SHUT THE ENGINE OFF!
7. Do not run the engine indoors, except when starting
the engine and for transporting the snow thrower in or
out of the building. Open the outside doors; exhaust
fumes are dangerous.
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean-out tool, not your hands.
8. Exercise extreme caution when operating on slopes.
Maintenance and Storage
1. Check shear bolts and other bolts at frequent intervals
for proper tightness to be sure the equipment is in safe
working condition.
9. Neveroperatethesnowthrowerwithoutproperguards,
and other safety protective devices in place and work-
ing.
10. Never direct the discharge toward people or areas
where property damage can occur. Keep children
and others away.
2. Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present
such as hot water heaters, space heaters, or clothes
dryers. Allow the engine to cool before storing in any
enclosure.
11. Do not overload the machine capacity by attempting
to clear snow at too fast a rate.
12. Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care when
operating in reverse.
3. Always refer to operator’s manual for important details
if the snow thrower is to be stored for an extended
period.
13. Disengage power to the collector/impeller when snow
thrower is transported or not in use.
4. Maintain or replace safety and instruction labels, as
necessary.
14. Use only attachments and accessories approved by
the manufacturer of the snow thrower (such as wheel
weights, counterweights, or cabs).
5. Run the machine a few minutes after throwing snow
to prevent freeze-up of the collector/impeller.
15. Never operate the snow thrower without good visibility
or light. Always be sure of your footing, and keep a firm
hold on the handles. Walk; never run.
16. Never touch a hot engine or muffler.
CONGRATULATIONS on your purchase of a new snow
thrower. Ithasbeendesigned,engineeredandmanufactured
to give best possible dependability and performance.
PRODUCT SPECIFICATIONS
Gasoline Capacity 4.0 Quarts
and Type:
Unleaded Regular only
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
center. We have competent, well-trained technicians and
the proper tools to service or repair this unit.
Oil Type
(API SG–SL):
SAE 30 (above 40°F)
SAE 5W-30 or 10W-30 (0° to +40°F)
SAE 0W-30 (below 0°F)
Please read and retain this manual. The instructions will
enable you to assemble and maintain your snow thrower
properly. Always observe the “SAFETY RULES”.
Oil Capacity:
Spark Plug:
26 Ounces
Champion RN4C (Gap: .030")
SERIAL NUMBER: ___________________________
DATE OF PURCHASE: _______________________
CUSTOMER RESPONSIBILITIES
•
•
Read and observe the safety rules.
THEMODELANDSERIALNUMBERSWILLBEFOUND
ONADECALATTACHEDTOTHEREAROFTHESNOW
THROWER HOUSING.
Follow a regular schedule in maintaining, caring for
and using your snow thrower.
•
Followtheinstructionsunder“Maintenance”and“Stor-
age” sections of this owner’s manual.
YOUSHOULDRECORDBOTHSERIALNUMBERAND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
TABLE OF CONTENTS
SAFETY RULES ........................................................ 2-3
MAINTENANCE..................................................... 14-15
MAINTENANCE SCHEDULE ..................................... 14
SERVICE AND ADJUSTMENTS ........................... 16-18
STORAGE................................................................... 18
TROUBLESHOOTING................................................ 19
REPAIR PARTS ..................................................... 20-31
PRODUCT SPECIFICATIONS...................................... 3
CUSTOMER RESPONSIBILITIES................................ 3
WARRANTY................................................................ 32
ASSEMBLY / PRE-OPERATION............................... 5-7
OPERATION ............................................................ 8-14
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS PACKED SEPARATELY IN CARTON
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY / PRE-OPERATION
Read these instructions and this manual in its entirety before you attempt to assemble or operate your new
snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly,
operation and maintenance of the product.
Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for shipping
purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts
bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened
securely. Use the correct tools as necessary to ensure proper tightness.
REMOVE SNOW THROWER FROM CARTON
SPEED
1. Remove all accessible loose parts and parts boxes
CONTROL
from carton.
ROD
2. Cut down all four corners of carton and lay panels flat.
PLASTIC TIE
3. Removethetwo(2)screwssecuringtheaugerhousing
to the pallet.
UPPER
HANDLE
4. Removeallpackingmaterialsexceptplastictieholding
speed control rod to lower handle.
5. Remove the two (2) plastic ties securing the upper
handle to the pallet.
HANDLE
KNOB
6. Remove snow thrower from carton and check carton
thoroughly for additional loose parts.
LOWER
HANDLE
HOW TO SET UP YOUR SNOW THROWER
TOOL BOX (See Fig. 10)
A toolbox is provided on your snow thrower. The toolbox is
located on top of the belt cover. Store the extra shear bolts,
nuts and multi-wrench provided in parts bag in the toolbox.
NOTE: The multi-wrench may be used for assembly of the
chuterotatorheadtosnowthrowerandmakingadjustments
to the skid plates.
UNFOLD UPPER HANDLE
1. Raiseupperhandletotheoperatingpositionandtighten
handle knobs securely.
FIG. 1
SPEED CONTROL ROD
INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)
1. Remove plastic tie securing rod to lower handle.
RETAINER
SPRING
2. Insert rod into speed control bracket and secure with
retainer spring.
SPEED
CONTROL
BRACKET
SPEED
CONTROL
LEVER
FIG. 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY / PRE-OPERATION
INSTALL TRACTION DRIVE CONTROL ROD
INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)
(See Figs. 3 and 4)
The traction drive control rod has the long loop on the end
of the spring as shown.
The auger control rod has the short loop on the end of the
spring as shown.
1. Slide rubber sleeve up rod and hook end of spring into
control arm with loop opening up as shown.
1. Slide rubber sleeve up rod and hook end of spring into
pivot bracket with loop opening down as shown.
2. Withtopendofrodpositionedunderrightsideofcontrol
panel, push down on rod and insert end of rod into hole
in auger control bracket. Secure with retainer spring.
2. With top end of rod positioned under left side of control
panel, pushroddownandinserttopendofrodintohole
in drive control bracket. Secure with retainer spring.
TRACTION DRIVE
CONTROL ROD
AUGER
CONTROL
ROD
RUBBER
SLEEVE
RUBBER
SLEEVE
CONTROL
ARM
LOOP
OPENING
DOWN
LOOP
OPENING
UP
PIVOT
BRACKET
FIG. 3
FIG. 5
AUGER CONTROL ROD
AUGER
CONTROL
LEVER
TRACTION DRIVE
CONTROL LEVER
RETAINER
SPRING
RETAINER
SPRING
TRACTION
DRIVE
CONTROL
ROD
DRIVE
CONTROL
BRACKET
AUGER
CONTROL
BRACKET
FIG. 6
FIG. 4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY / PRE-OPERATION
INSTALL CHUTE DEFLECTOR REMOTE CONTROL
(See Figs. 8 and 9)
1. Install remote cable bracket to discharge chute with
5/16-18 carriage bolt and 5/16-18 locknut as shown.
Tighten securely.
INSTALLDISCHARGECHUTE/CHUTEROTATERHEAD
(See Fig. 7)
NOTE: The multi-wrench provided in your parts bag may
be used to install the chute rotater head.
1. Place discharge chute assembly on top of chute base
with discharge opening toward front of snow thrower.
2. Install remote cable eyelet to chute deflector with
1/4-20 shoulder bolt, nylon friction washer and 1/4-20
locknut as shown. Tighten securely.
2. Positionchuterotaterheadoverchutebracket. Ifneces-
sary,rotatechuteassemblytoalignsquareandpinonun-
dersideofchuterotaterheadwithholesinchutebracket.
3. Install spring hooks between hex nuts on chute rotater
head and into hole in chute deflector as shown.
3. With chute rotater head and chute bracket aligned,
position chute rotater head on pin and threaded stud
of mounting bracket.
CHUTE
SPRING
1/4-20
SHOULDER
BOLT
DEFLECTOR
4. Install 3/8 washer and locknut on threaded stud and
tighten securely.
NYLON
WASHER
HOOK BETWEEN
HEX NUTS
CABLE
EYELET
ON CHUTE
CHUTE
ROTATER
HEAD
ROTATER HEAD
3/8 LOCKNUT
3/8 WASHER
1/4-20
LOCK-
NUT
5/16-18
CARRIAGE
BOLT
REMOTE
CABLE
BRACKET
PIN
5/16-18
LOCKNUT
THREADED
STUD
FIG. 8
ROTATER HEAD
MOUNTING
CHUTE
ALIGN BEFORE
BRACKET
BRACKET TIGHTENING LOCKNUT
FIG. 7
CHUTE DEFLECTOR
CONTROL LEVER
FIG. 9
CHECK TIRE PRESSURE
Thetiresonyoursnowthrowerwereoverinflatedatthefac-
tory for shipping purposes. Correct and equal tire pressure
is important for best snow throwing performance.
•
Reduce tire pressure to 14-17 PSI (19-24.5 N-m).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KNOW YOUR SNOW THROWER
READ THIS OWNER'S MANUALANDALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare
the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save
this manual for future reference.
These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand
their meaning.
PRIMER
DANGER
OR WARNING
READ AND FOLLOW ALL SAFETY INFORMATION
AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
FORWARD REVERSE
IGNITION KEY.
INSERT TO START
AND RUN,
PULL OUT TO STOP.
DISENGAGED
ENGAGED
SNOW
TRACTION
DISCHARGE
DRIVE CONTROL
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SPARK
PLUG
ENGINE OIL CAP
WITH DIPSTICK
AUGER
CONTROL
LEVER
DISCHARGE CHUTE CONTROL LEVER
SAFETY
IGNITION
KEY
TRACTION
DRIVE SPEED
DRIVE
CONTROL
LEVER
CONTROL LEVER
GASOLINE
FILLER
CAP
CHUTE
DEFLECTOR
CHOKE
CON-
TROL
FUEL
SHUT-OFF
VALVE
LH TURN
TRIGGER
THROTTLE
/ ENGINE
CONTROL
DEFLECTOR
REMOTE
CONTROL
LEVER
DISCHARGE
CHUTE
RECOIL
POWER
CORD
PLUG
LIGHT
(AUXILIARY)
STARTER
HANDLE
ELECTRIC
START
BUTTON
OIL DRAIN PLUG
CLEAN-OUT TOOL
HANDLE
KNOB
PRIMER
MUFFLER
TOOLBOX
NOTE: ITEMS ABOVE
ARE SHOWN IN
THEIR TYPICAL
LOCATION ON THE
ENGINE. ACTUAL
LOCATION MAY VARY
WITH THE ENGINE
ON YOUR UNIT.
DRIFT
CUTTER
SKID PLATE
AUGERS
FIG. 10
MEETS A.N.S.I. SAFETY REQUIREMENTS
Our snow throwers conform to the standards of the American National Standards Institute.
Toolbox - used to store spare shear bolts, locknuts and
wrench.
Drive speed control lever - used to select forward or
reverse motion and speed of snow thrower.
Safety ignition key - must be inserted for the engine to
start and run. Remove when snow thrower is not in use.
Traction drive control lever - used to engage power-pro-
pelled forward or reverse motion of snow thrower.
Electric start button - used for starting the engine.
Auger control lever - used to engage auger motion (throw
snow).
Recoil(auxiliary)starterhandle-usedforstartingengine.
Discharge chute control lever - used to change the di-
rection the snow is thrown.
Primer - pumps additional fuel from the carburetor to the
cylinder for use when starting a cold engine.
Deflector remote control lever - used to change the
distance the snow is thrown.
Choke Control - used for starting a cold engine.
Throttle/engine control - used to select either FAST or
SLOW engine speed and to STOP the engine.
Skid plate - used to adjust height of scraper bar from the
ground.
LH and RH turn triggers - used to steer the snow thrower.
Drift cutter - used to cut through deep snowdrifts.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO USE CHOKE CONTROL (See Fig. 13)
The operation of any snow thrower can result
in foreign objects thrown into the eyes, which
canresultinsevereeyedamage. Alwayswear
safety glasses or eye shields while operating
your snow thrower or performing any adjust-
The choke control is located on the engine. Use the choke
control whenever you are starting a cold engine. Do not
use to start a warm engine.
•
To engage choke, turn knob clockwise. Slowly turn
knob counterclockwise to disengage.
ments or repairs. We recommend standard safety glasses
or a wide vision safety mask worn over spectacles.
HOW TO USE YOUR SNOW THROWER
Know how to operate all controls before adding fuel or
attempting to start the engine.
OFF
FULL
STOPPING
TRACTION DRIVE
•
Release traction drive control lever to stop the forward
or reverse movement of the snow thrower.
FIG. 13
AUGER
TO CONTROL SNOW DISCHARGE (See Fig. 14)
•
Release the auger control lever to stop throwing snow.
WARNING: Snow throwers have ex-
posed rotating parts, which can cause
severe injury from contact, or from ma-
terial thrown from the discharge chute.
Keep the area of operation clear of all
persons, small children and pets at all
times including startup.
ENGINE
1. Move throttle control to “STOP” position.
2. Remove (do not turn) safety ignition key to prevent
unauthorized use.
NOTE: Never use choke to stop engine.
TO USE FUEL SHUT-OFF VALVE (See Fig. 11)
WARNING:Ifthedischargechuteorau-
ger become clogged, shut-off engine
andwaitforallmovingpartstostop.Use
the clean-out tool, NOT YOUR HANDS,
to unclog the chute and/or auger.
The fuel shut-off valve is located beneath the fuel tank on
the engine. Always operate the snow thrower with the fuel
shut-off valve in the OPEN position.
TheDIRECTIONinwhichsnowistobethrowniscontrolled
by the discharge chute control lever.
•
To change the discharge chute position, press down-
ward on discharge chute control lever and move lever
left or right until chute is in desired position. Be sure
lever springs back and locks into desired position.
OFF
The DISTANCE that snow is thrown is controlled by the
position of the chute deflector. Set the deflector low to
throw snow a short distance; set the deflector higher to
throw snow farther.
OPEN
FIG. 11
•
Press downward on chute deflector control lever and
moveleverforwardtolowerthedeflectoranddecrease
the distance. Move lever back to raise the deflector
and increase the distance. Be sure lever springs back
and locks into desired position.
TO USE THROTTLE CONTROL (See Fig. 12)
Thethrottlecontrolislocatedontheengine.Alwaysoperate
the snow thrower with the engine at full throttle. Full throttle
offers the best snow thrower performance.
DISCHARGE CHUTE
CONTROL LEVER
FAST
SLOW
CHUTE DEFLECTOR
REMOTE CONTROL LEVER
10
FIG. 12
FIG. 14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO MOVE FORWARD AND BACKWARD (See Fig. 17)
TO THROW SNOW (See Fig. 15)
SELF-PROPELLING, forward and reverse movement of
the snow thrower, is controlled by the traction drive control
lever located on the left side handle.
The auger rotation is controlled by the auger control lever
located on the right side handle.
•
Squeeze auger control lever to handle to engage the
auger and throw snow.
•
Squeezetractiondrivecontrollevertohandletoengage
the drive system.
•
Release the auger control lever to stop throwing snow.
•
Release traction drive control lever to stop the forward
or reverse movement of the snow thrower.
AUGER
CONTROL
LEVER
SPEED and DIRECTION are controlled by the drive speed
control lever.
•
Press downward on the speed control lever and move
lever to desired position BEFORE engaging the trac-
tion drive control lever. Be sure lever springs back and
locks into desired position.
CAUTION: Do not move speed control lever
when traction drive control lever is engaged.
Damage to the snow thrower can result.
FIG. 15
•
Slower speeds are for heavier snow and faster speeds
are for light snow and transporting the snow thrower. It
is recommended that you use a slower speed until you
are familiar with the operation of the snow thrower.
USING THE CLEAN-OUT TOOL (See Fig. 16)
In certain snow conditions, the discharge chute may be-
come clogged with ice and snow. Use the clean-out tool to
dislodge this blockage.
NOTE: When both traction drive and auger control levers
are engaged, the traction drive control lever will lock the
auger control lever in the engaged position. This will allow
you to release your right hand from the handle and adjust
the discharge chute direction without interrupting the snow
throwing process.
When cleaning, repairing, or inspecting, make
certain all controls are disengaged and the
auger/impeller and all moving parts have
stopped. Disconnect the spark plug wire and
keep the wire away from the spark plug to pre-
vent accidental starting.
TRACTION DRIVE
CONTROL LEVER
•
•
Releasetheaugercontrolleverandshutofftheengine.
Removetheclean-outtoolfromit'smountingclip. Grasp
the tool firmly by the handle and push and twist the tool
into the discharge chute to dislodge the blockage.
Afterthepackedsnowhasbeendislodged,returntheclean-
out tool to it's mounting clip by pushing it into the clip.
•
Makesurethedischargechuteispointedinasafedirec-
tion(novehicles,buildings,people,orotherobjectsare
in the direction of discharge) before restarting engine.
DRIVE SPEED
CONTROL LEVER
•
Restart the engine, then squeeze the auger control
lever to the handle to clear snow from the auger hous-
ing and the discharge chute.
FIG. 17
POWER STEERING OPERATION (See Fig. 18)
Steering triggers are used to assist in steering your snow
thrower. The triggers are located on the underside of each
handle. Whenatriggerissqueezed, itdisengagesthedrive
wheel on that side of snow thrower and allows it to turn in
that direction.
DISCHARGE CHUTE
•
•
To turn left – squeeze left side trigger.
To turn right – squeeze right side trigger.
CLEAN-OUT
TOOL
LH TURN
TRIGGER
RH TURN
TRIGGER
MOUNTING CLIP
FIG. 16
Download from Www.Somanuals.com. All Manuals Search And Download.
FIG. 18
11
OPERATION
•
When not using drift cutters, loosen adjustment nut,
lower to storage position and tighten nut securely.
TO ADJUST SKID PLATES (See Fig. 19)
NOTE:Thewrenchprovidedinyourpartsbagmaybeused
to adjust the skid plates.
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL (See Fig. 21)
The engine on your snow thrower has been shipped, from
the factory, already filled with oil.
Skid plates are located on each side of the auger housing
and adjust the clearance between the scraper bar and the
ground surface. Adjust skid plates evenly to proper height
for current surface conditions. For removal of snow in
normal conditions, such as a paved driveway or sidewalk,
place skid plates in the highest position (lowest scraper
clearance) to give a 1/8" clearance between the scraper
bar and the ground. Use a middle position if the surface
to be cleared is uneven.
1. Check engine oil with snow thrower on level ground.
2. Remove oil fill cap/dipstick and wipe clean, reinsert
the dipstick and screw tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
NOTE: It is not recommended to operate the snow thrower
overgravelorrockysurfaces.Objectssuchasgravel,rocks
or other debris, can easily be picked up and thrown by the
impeller, which can cause serious personal injury, property
damage or damage to the snow thrower.
•
To change engine oil, see “TO CHANGE ENGINE OIL”
in the Maintenance section of this manual.
ADD GASOLINE (See Fig. 21)
•
Fill fuel tank to bottom of tank filler neck. Do not over-
fill. Use fresh, clean, regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
•
If snow thrower must be operated over gravel surface,
use extra caution and be sure skid plates are adjusted
to lowest (highest scraper clearance) position.
1. Shut off engine and wait for all moving parts to stop.
2. Adjust skid plates by loosening the rear 1/2" hex nut
only,thenmovingskidplatetodesiredposition.Besure
both plates are adjusted evenly. Tighten securely.
WARNING: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
HIGH POSITION
(LOW GROUND
CLEARANCE)
CAUTION: Alcohol blended fuels (called gas-
ohol or using ethanol or methanol) can attract
moisture which leads to separation and for-
mation of acids during storage. Acidic gas can
damage the fuel system of an engine while in
storage. To avoid engine problems, the fuel
system should be emptied before storage of
30 days or longer. Drain the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. SeeStorageInstructionsforadditional
information. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
AUGER
HOUSING
SKID PLATE
1/2" HEX NUT
LOW POSITION (HIGH GROUND CLEARANCE)
FIG. 19
SCRAPER BAR
The scraper bar is not adjustable, but is reversible. After
considerable use it may become worn. When it has worn
almost to the edge of the housing, it can be reversed,
providing additional service before requiring replacement.
Replace a damaged or worn scraper bar.
CHOKE CONTROL
THROTTLE PRIMER
ENGINE OIL
FILL CAP /
DIPSTICK
TO USE DRIFT CUTTERS (See Fig. 20)
Use the drift cutters to cut through deep snowdrifts that are
higher than the front of the snow thrower.
SAFETY
IGNITION
KEY
•
Loosen upper adjustment nut enough to allow drift
cutter to be raised to highest position and tighten nut
securely. Repeat for opposite side of snow thrower.
AUGER
HOUSING
GASOLINE
FILLER CAP
STORAGE
POSITION
DRIFT
CUTTER
FUEL SHUT-
OFF VALVE
RECOIL
STARTER
HANDLE
STARTER BUTTON
POWER CORD PLUG
ADJUST-
MENT NUT
NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
FIG. 20
12
FIG. 21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO START ENGINE
Be sure fuel shut-off valve is in the OPEN position.
6. When the engine starts, release the recoil starter
handle and slowly move the choke control to the OFF
position.
•
Your snow thrower engine is equipped with both a 120 Volt
A.C. electric starter and a recoil starter. The electric starter
is equipped with a three-wire power cord and plug and is
designed to operate on 120 Volt A.C. household current.
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operating
temperature.
WARM START - RECOIL STARTER
•
Be sure your house is a 120 Volt A.C. three-wire
grounded system. If you are uncertain, consult a
licensed electrician.
Follow the steps above, keeping the choke in the OFF
position. DO NOT push the primer.
BEFORE STOPPING
Run the engine for a few minutes to help dry off any mois-
ture on the engine.
WARNING: Do not use the electric
starter if your house is not a 120 Volt
A.C. three-wire grounded system. Se-
riouspersonalinjuryordamagetoyour
snow thrower could result.
To avoid possible freeze-up of the starter, proceed as fol-
lows:
ELECTRIC STARTER
COLD START - ELECTRIC STARTER
1. Connect the power cord to the engine.
1. Insert safety ignition key (packed separately in parts
bag)intoignitionslotuntilitclicks. DONOTturnthekey.
Keep the extra safety ignition key in a safe place.
2. Plug the other end of the power cord into a three-hole
grounded 120 Volt A.C. receptacle.
2. Place throttle control in FAST position.
3. Rotate choke control to FULL position.
4. Connect the power cord to the engine.
3. While the engine is running, push starter button and
spin the starter for several seconds.
NOTE: The unusual sound made while starter is spinning
will not harm the engine or starter.
5. Plug the other end of the power cord into a three-hole
grounded 120 Volt A.C. receptacle.
4. Disconnect the power cord from the receptacle first,
then from the engine.
6. Push the primer three (3) times.
RECOIL STARTER
7. Push starter button until engine starts.
1. Whiletheengineisrunning,pulltherecoilstarterhandle
with rapid, full arm strokes three or four times.
IMPORTANT: Do not crank engine more than five con-
tinuous seconds between each time you try to start. Wait
5 to 10 seconds between each attempt.
NOTE: The unusual sound made while pulling the recoil
starter handle will not harm the engine or starter.
8. When the engine starts, release the starter button and
slowly move the choke control to the “OFF” position.
IF RECOIL STARTER HAS FROZEN
If the recoil starter has frozen and will not turn the engine,
proceed as follows:
9. Disconnect the power cord from the receptacle first,
then from the engine.
1. Grasp the recoil starter handle and slowly pull as much
rope out of the starter as possible.
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operat-
ing temperature.
2. Release the recoil starter handle and let it snap back
against the starter.
WARM START - ELECTRIC STARTER
If the engine still fails to start, repeat the above steps or
use the electric starter.
Follow the steps above, keeping the choke control in the
OFF position.
COLD START - RECOIL STARTER
SNOW THROWING TIPS
1. Insert safety ignition key into the ignition slot until it
clicks. DO NOT turn the key. Keep the extra safety
ignition key in a safe place.
•
•
•
•
Always operate the snow thrower with the engine at
full throttle. Full throttle offers the best performance.
Goslowerindeep,freezingorheavywetsnow.Usethe
drive speed control, NOT the throttle, to adjust speed.
2. Place throttle control in FAST position.
3. Rotate choke control to FULL position.
It is easier and more efficient to remove snow imme-
diately after it falls.
4. Push the primer four (4) times if the temperature is
below 15°F, or two (2) times if temperature is between
15° and 50°F. If temperature is above 50°F, priming is
not necessary.
The best time to remove snow is the early morning. At
this time the snow is usually dry and has not been ex-
posed to the direct sun and warming temperatures.
NOTE: Over priming may cause flooding, preventing the
engine from starting. If you do flood the engine, wait a few
minutes before attempting to start and DO NOT push the
primer.
•
Slightly overlap each successive path to ensure all
snow will be removed.
•
•
Throw snow downwind whenever possible.
Adjust the skid plates to proper height for current snow
conditions. See “TO ADJUST SKID PLATES” in this
section of this manual.
5. Pull recoil starter handle quickly. Do not allow starter
rope to snap back.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
•
For extremely heavy snow, reduce the width of snow
removal by overlapping previous path and moving
slowly.
WARNING: Do not operate snow
throwerifweatherconditionsimpairvis-
ibility. Throwing snow during a heavy,
windysnowstormcanblindyouandbe
hazardous to the safe operation of the
snow thrower.
•
•
•
Keep engine clean and clear of snow during use. This
will help air flow and extend engine life.
Aftersnow-throwingiscompleted,allowenginetorunfor
a few minutes to melt snow and ice off the engine.
Clean the entire snow thrower thoroughly after each
use and wipe dry so it is ready for next use.
MAINTENANCE
GENERAL RECOMMENDATIONS
LUBRICATION CHART
Thewarrantyonthissnowthrowerdoesnotcoveritemsthat
have been subjected to operator abuse or negligence. To
receivefullvaluefromthewarranty,operatormustmaintain
snow thrower as instructed in this manual. Some adjust-
mentswillneedtobemadeperiodicallytoproperlymaintain
your snow thrower.
SAE 5W-30 Motor Oil
See “ENGINE” in
Maintenance section
General
Purpose
Grease
All adjustments in the Service and Adjustments section of
this manual should be checked at least once each season.
•
Once a year, you should replace the spark plug and
check belts for wear. A new spark plug will help your
engine run better and last longer.
Pivot points
•
Follow the maintenance schedule in this manual.
NOTE: Use only Original Equipment Manufacturer (OEM)
parts to service this unit. Failure to do so can cause the unit
to malfunction and pose a risk of injury to the operator.
BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
3. Checkcontrolstobesuretheyarefunctioningproperly.
LUBRICATION
Keep your snow thrower well lubricated
(See “LUBRICATION CHART”).
Auger
grease fittings
Engine oil
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Checkthecrankcaseoillevelbeforestartingtheengineand
SNOW THROWER
after each five (5) hours of continuous use. Tighten oil fill
cap / dipstick securely each time you check the oil level.
Alwaysobservesafetyruleswhenperformingmaintenance.
TIRES
•
TO CHANGE ENGINE OIL
Maintain proper air pressure in both tires (14–17 P.S.I.
/ 19-24.5 N-m).
Determine temperature range anticipated before next oil
change.AlloilmustmeetAPIserviceclassificationSG–SL.
•
Keep tires free of gasoline / oil, which can harm rubber.
•
•
•
Be sure snow thrower is on level surface.
Oil will drain more freely when warm.
Catch oil in a suitable container.
NOTE:Tosealtirepuncturesandpreventflattiresduetoslow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and corrosion.
NOTE: The left side wheel may be removed from snow
thrower for easier access to the oil drain plug and place-
ment of a suitable container. The unit tilted, resting on the
frame with the left wheel removed, will help drain any oil
trapped inside the engine. (See “TO REMOVE WHEELS”
in the Service and Adjustments section of this manual).
V-BELTS
Check V-belts for deterioration and wear after every 50
hours of operation and replace if necessary. The belts
are not adjustable. Replace belts if they begin to slip from
wear. (See “TO REMOVE BELT COVER” in the Service
and Adjustments section of this manual).
1. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
TheV-beltsonyoursnowthrowerareofspecialconstruction
andshouldbereplacedbyoriginalequipmentmanufacturer
(OEM) belts available from your dealer. Using other than
OEMbeltscancausepersonalinjury/damagetothethrower.
2. Clean area around drain plug.
3. Remove drain plug and drain oil in a suitable container.
4. Install drain plug and tighten securely.
AUGER GEAR CASE
5. Wipe off any spilled oil from snow thrower and engine.
•
Thegearcasewasfilledwithlubricanttotheproperlevel
at the factory. The only time the lubricant needs atten-
tion is if service has been performed on the gear case.
6. Install left wheel (if removed for draining oil). Be sure to
install klick pin into proper hole in wheel axle (See “TO
REMOVE WHEELS” in the Service and Adjustments
section of this manual).
•
If lubricant is required, use only Ronex ED #1 grease.
TRACTION DRIVE SYSTEM
7. Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine.
DO NOT lubricate the drive components inside the snow
thrower. The sprockets, hex shafts, drive disc and friction
wheel require no lubrication. The bearings and bushings
are lifetime lubricated and require no maintenance.
8. Refill engine with oil through oil dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCTSPECIFICATIONS”sectionofthismanual.
9. Use gauge on oil fill cap/dipstick for checking level. Be
sure dipstick cap is tightened securely for accurate
reading. Keep oil at “FULL” line on dipstick.
CAUTION:Anylubricatingoftheabovecompo-
nents can cause contamination of the friction
wheel and damage to the drive system of your
snow thrower.
10. Wipe off any spilled oil.
MUFFLER
ENGINE
See engine manual.
Inspect and replace corroded muffler as it could create a
fire hazard and/or damage.
LUBRICATION
SPARK PLUG
Use only high quality detergent oil rated with API service
classification SG–SL. Select the oil's SAE viscosity grade
according to your expected operating temperature.
Replacesparkplugatthebeginningofeachseasonorafter
every100hoursofoperation,whicheveroccursfirst. Spark
plug type and gap setting are shown in the “PRODUCT
SPECIFICATIONS” section of this manual.
CLEANING
IMPORTANT: For best performance, keep snow thrower
housing free of any dirt or trash. Clean the outside of your
snow thrower after each use.
WARNING: Disconnectsparkplugwire
fromsparkplugandplacewirewhereit
cannot come in contact with plug.
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
possible engine damage from running low on oil.
•
•
Keep finished surfaces/wheels free of gasoline, oil,
etc.
We do not recommend using a garden hose to clean
yoursnowthrowerunlesstheelectricalsystem,muffler
and carburetor are covered to keep water out. Water
in engine can result in shortened engine life.
Change the oil after every 25 hours of operation or at least
once a year if thrower is not used for 25 hours in one year.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
1. Disengage all controls and move throttle control to
WARNING: To avoid serious injury,
before performing any service or ad-
justments:
STOP position. Wait for all moving parts to stop.
2. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
1. Be sure throttle is in STOP position.
2. Remove safety ignition key.
3. Align holes in impeller hub with holes in impeller shaft
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear
bolts. Install 1/4-20 locknuts and tighten securely.
3. Make sure the augers and all moving
parts have completely stopped.
CAUTION: Do not substitute. Use only original
equipment capscrew/shear bolts as supplied
with your snow thrower.
4. Disconnect spark plug wire from
spark plug and place wire where it
cannot come in contact with plug.
4. Connect spark plug wire to spark plug.
SNOW THROWER
1/4-20
LOCKNUT
1/4-20 x 1-5/8
CAPSCREW /
SHEAR BOLT
1/4-20 x 2
SHOULDER /
SHEAR BOLT
TO ADJUST SNOW THROWER HEIGHT
See “TO ADJUST SKID PLATES” and “SCRAPER BAR”
in the Operation section of this manual.
SPACER
IMPELLER HUB
CHUTE DEFLECTOR
IMPELLER
SHAFT
The chute deflector, attached to the top of the discharge
chute, is provided to direct discharging snow away from
the operator. If the deflector becomes damaged, it should
be replaced.
WARNING: To avoid serious injury,
never operate your snow thrower with
the deflector removed or damaged.
•
Tochangedirectionand/ordistancesnowisdischarged,
see “TO CONTROL SNOW DISCHARGE” in the Op-
eration section of this manual.
AUGER
HUB
SHEAR BOLTS (See Fig. 22)
1/4-20
LOCKNUT
AUGER SHEAR BOLTS
AUGER HUB
AUGER SHAFT
Both right and left-hand augers are secured to the auger
shaft with a shoulder/shear bolt and hex nut. Should a for-
eign object or ice become lodged in the augers, the shear
bolts are designed to break, preventing damage to any
other components. If one or both augers do not turn when
auger control lever is engaged, check to see if one or both
of the bolts have sheared. To replace the shear bolts:
FIG. 22
TO REMOVE BELT COVER (See Fig. 23)
1. Remove the two (2) screws securing belt cover to
frame.
1. Disengage all controls and move throttle control to
STOP position. Wait for all moving parts to stop.
2. Remove belt cover.
•
Replace belt cover by installing cover and screws and
tighten securely.
2. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
3. Alignholeinaugerhubwithholeinaugershaftandinstall
anew1/4-20x2"shoulder/shearboltwithspacer.Install
1/4-20 lock nut and tighten securely.
BELT
COVER
CAUTION: Do not substitute. Use only original
equipment shear bolts as supplied with your
snow thrower.
4. Connect spark plug wire to spark plug.
IMPELLER SHEAR BOLTS
The impeller is secured to the impeller shaft with two (2)
capscrew/shearboltsandhexnuts. Shouldaforeignobject
or ice become lodged in the impeller, the capscrews are
designed to break, preventing damage to any other com-
ponents. If impeller does not turn when auger control lever
is engaged, check to see if the capscrews have sheared.
To replace the capscrew/shear bolts:
FRAME
SCREWS
FIG. 23
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
TO REPLACE BELTS (See Fig. 24)
The auger and traction drive belts are not adjustable. If the
belts are damaged or begin to slip from wear, they should
be replaced. It is recommended that the belt(s) be replaced
by a qualified service center.
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into
the square hole in idler arm and rotate ratchet clockwise
to relieve tension.
8. With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
NOTE: It is recommended that both the auger and traction
drive belt be replaced at the same time.
9. Placeaugerbeltaroundandinsidethegrooveofauger
pulley only.
TheV-beltsonyoursnowthrowerareofspecialconstruction
andshouldbereplacedbyoriginalequipmentmanufacturer
(OEM)beltsavailablefromyournearestdealer.Usingother
than OEM belts can cause personal injury or damage to
the snow thrower.
10. While your assistant slowly raises handles to rejoin
the auger housing and frame assembly, pull up on the
auger belt and squeeze sides together above pulley
so belt is fully seated in groove of pulley.
11. Bring snow thrower completely together and check
carefully for proper routing of belts. If auger belt has
becomedislodgedfromthepulley(bycatchingtheidler
arm bracket while bringing snow thrower together),
separate the snow thrower and repeat step 10. Belt
must be fully seated in pulley groove when bringing
the snow thrower together.
WARNING: Belt replacement requires
separation of the snow thrower. While
separating the auger housing from the
frame assembly, it is important that an
assistantstandintheoperatingposition
andholdthesnowthrowerhandles.Se-
rious personal injury and/or damage to
theunitcouldoccurifthesnowthrower
should fall during the belt changing
process.
12. Install the two (2) hex bolts and lock washers and
tighten securely.
13. INSTALLENGINEPULLEY-Placebeltinpulleygroove
and slide pulley on crankshaft. Install flat washer, lock-
washer and bolt and tighten securely (30-35 ft. lbs.
torque). Make sure belt is inside belt keeper.
FRAME
ASSEMBLY
AUGER
HOUSING
14. INSTALL BELT COVER and two (2) screws. Tighten
securely.
15. INSTALL DISCHARGE CHUTE – See “INSTALL DIS-
CHARGE CHUTE / CHUTE ROTATER HEAD” in the
Assembly / Pre-Operation section of this manual.
BELT KEEPER
TRACTION DRIVE BELT
ENGINE
HANDLES
1. REMOVEGASOLINEFROMFUELTANK-Draingaso-
line from fuel tank into a suitable container, outdoors,
away from fire or flame. Wipe up any spilled gasoline.
FLAT WASHER
PULLEY
LOCKWASHER
BOLT
2. REMOVE DISCHARGE CHUTE - Loosen locknut
securing chute rotator head to mounting bracket only
enough to allow chute rotator head to be raised and
discharge chute to be removed from snow thrower.
AUGER
BELT
IDLER ARM
SQUARE
HOLE
3. REMOVE BELT COVER - See “TO REMOVE BELT
COVER” in this section of this manual.
CLUTCHING
IDLER ARM
BRACKET
4. REMOVEENGINEPULLEY-Removebolt,lockwasher
and flat washer securing pulley to engine crankshaft.
Remove outside (auger) pulley only from crankshaft.
AUGER PULLEY
5. SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
remove the two (2) bolts and lock washers holding
auger housing and frame together.
BOLT
LOCK
WASHER
WARNING: As the last bolt is removed,
have your assistant carefully lower the
handles down to the ground.
6. REMOVE AUGER BELT from around pulley.
FRAME
AUGER
7. RELIEVE TENSION ON TRACTION DRIVE BELT
IDLER and remove traction drive belt from around
pulleys.
HOUSING
FIG. 24
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TO REMOVE WHEELS (See Fig. 25)
Remove the klik pin and remove wheel from axle.
NOTE: To seal punctures or prevent flat tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and corrosion.
•
IMPORTANT: When installing wheel, be sure to use the
axle hole closest to the end of the shaft – do not use the
hole in the wheel hub (if equipped). Inner hole in axle and
holeinwheelhubarenotusedforyourmodelsnowthrower.
ENGINE
See engine manual.
CARBURETOR
Your carburetor is not adjustable. Engine performance
should not be affected at altitudes up to 7,000 feet (2,134
meters). If your engine does not operate properly due to
suspected carburetor problems, take your snow thrower to
a qualified service center.
KLIK PIN (INSTALL
IN OUTER HOLE
OF AXLE ONLY)
OUTER HOLE
ENGINE SPEED
AXLE
Nevertamperwiththeenginegovernor, whichisfactoryset
for proper engine speed. Overspeeding the engine above
the factory high speed setting can be dangerous and will
void the warranty. If you think the engine-governed high
speed needs adjusting, contact a qualified service center,
which has proper equipment and experience to make any
necessary adjustments.
WHEEL
WHEEL HUB
FIG. 25
STORAGE
Immediately prepare your snow thrower for storage at the
end of the season or if the unit will not be used for 30 days
or more.
•
•
•
Empty the fuel tank by starting the engine and letting
it run until the fuel lines and carburetor are empty.
Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
WARNING: Never store the snow
throwerwithgasolineinthetankinside
a building where fumes may reach an
open flame, spark or pilot light as on a
furnace, water heater, clothes dryer or
gasappliance. Allowtheenginetocool
before storing in any enclosure.
Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in min-
imizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not drain the
gas tank and carburetor if using fuel stabilizer.
SNOW THROWER
When snow thrower is to be stored for a period of time,
clean it thoroughly, remove all dirt, grease, leaves, etc.
Store in a clean, dry area.
ENGINE OIL
Drain oil (with engine warm) and replace with clean en-
gine oil. (See “ENGINE” in the Maintenance section of
this manual).
1. Clean entire snow thrower (See “CLEANING” in the
Maintenance section of this manual).
CYLINDER
1. Remove spark plug.
2. Inspect and replace belts, if necessary (See “TO RE-
PLACEBELTS”intheServiceandAdjustmentssection
of this manual).
2. Pour one ounce (29 ml) of oil through spark plug hole
into cylinder.
3. Lubricate as shown in the Maintenance section of this
manual.
3. Pullrecoilstarterhandleslowlyafewtimestodistribute
oil.
4. Besurethatallnuts,bolts,screws,andpinsaresecurely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
4. Replace with new spark plug.
OTHER
5. Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
•
Do not store gasoline from one season to another.
•
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
ENGINE
See engine manual.
•
•
If possible, store your snow thrower indoors and cover
it to protect it from dust and dirt.
FUEL SYSTEM
Coveryoursnowthrowerwithasuitableprotectivecover
thatdoesnotretainmoisture.Donotuseplastic.Plastic
cannotbreathe,whichallowscondensationtoformand
will cause your snow thrower to rust.
IMPORTANT: It is important to prevent gum deposits from
forming in essential fuel system parts such as carburetor,
fuelhose,ortankduringstorage.Also,alcoholblendedfuels
(called gasohol or using ethanol or methanol) can attract
moisture which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel system of
an engine while in storage.
IMPORTANT: Never cover snow thrower while engine/
exhaust area is still warm.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
See appropriate section in manual unless directed to a qualified service center.
PROBLEM
CAUSE
CORRECTION
Does not start
1. Fuel shut-off valve (if so
equipped) in OFF position.
1. Turn fuel shut-off valve to OPEN position.
2. Safety ignition key
is not inserted.
2. Insert safety ignition key.
3. Out of fuel.
3. Fill fuel tank.
4. Throttle in STOP position.
5. Choke in OFF position.
6. Primer not depressed.
7. Engine is flooded.
8. Spark plug wire is
disconnected.
4. Move throttle to FAST position.
5. Move to FULL position.
6. Prime as instructed in the Operation section of this manual.
7. Wait a few minutes before restarting, DO NOT prime.
8. Connect wire to spark plug.
9. Bad spark plug.
10. Stale fuel.
11. Water in fuel.
9. Replace spark plug.
10. Drain fuel tank and carburetor, refill tank with fresh gasoline.
11. Drain fuel tank and carburetor, refill tank with fresh gasoline.
Loss of power
1. Spark plug wire loose.
2. Throwing too much snow.
3. Fuel tank cap is covered
with ice or snow.
1. Reconnect spark plug wire.
2. Reduce speed and width of swath.
3. Remove ice and snow on and around fuel tank cap.
4. Dirty or clogged muffler.
4. Clean or replace muffler.
Engine idles or
runs roughly
1. Choke is in FULL position.
2. Blockage in fuel line.
3. Stale fuel.
4. Water in fuel.
5. Carburetor is in need of
adjustment or overhaul.
1. Move choke to OFF position.
2. Clean fuel line.
3. Drain tank and refill with fresh, clean fuel.
4. Drain fuel tank and carburetor, refill tank with fresh gasoline.
5. Contact a qualified service center.
Excessive
vibration
1. Loose parts or damaged
augers or impeller.
1. Tighten all fasteners. Replace damaged parts.
If vibration remains, contact a qualified service center.
Recoil starter
is hard to pull
1. Frozen recoil starter.
1. See “IF RECOIL STARTER HAS FROZEN”
in the Operation section of this manual.
Loss of traction 1. Drive belt is worn.
1. Check / replace drive belt.
2. Check / reinstall drive belt.
drive / slowing
of drive speed
2. Drive belt is off of pulley.
3. Friction drive wheel is worn. 3. Contact a qualified service center.
Loss of snow
discharge or
slowing of
1. Auger belt is off of pulley.
2. Auger belt is worn.
3. Clogged discharge chute.
1. Check / reinstall auger belt.
2. Check / replace auger belt.
3. Clean snow chute.
snow discharge 4. Augers / impeller jammed.
4. Remove debris or foreign object from augers / impeller.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
AUGER HOUSING / IMPELLER ASSEMBLY
SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17
13
16
4
6
15
6
10
12
51
14
47
38
5
7
36
9
37
7
11
9
42
44
27
8
45
50
6
43
43
42
41
46
27
52
24
21
23
40
39
10
49
28
53
55
19
32
54
18
34
48
26
19
33
20
35
21
19
29
28
25
55
53
10
31
52
17
24
57
54
56
30
23
18
26
25
21
17
20
22
20
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
AUGER HOUSING / IMPELLER ASSEMBLY
SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17
KEY PART
NO. NO.
KEY PART
NO. NO.
DESCRIPTION
DESCRIPTION
4
5
6
7
532 19 10-79 Pulley, Impeller
532 18 89-09 Bearing Assembly, Flange
532 19 85-41 Nut, Hex Flange 5/16-18
532 18 03-55 Bolt, Flat Head, Carriage
5/16-18 x 5/8
31 532 40 77-23 Auger Assembly, LH
32 532 40 77-68 O-Ring
33 532 40 77-69 Bushing, Flange 3/4
34 532 17 46-81 Washer, Thrust 3/4
35 532 17 46-84 Bearing, Thrust 3/4
36 532 40 77-57 Shaft, Impeller
37 532 17 46-83 Washer, Thrust 5/8
38 532 40 77-58 Bushing, Flange 5/8
39 532 40 77-67 Screw, Hex Head 5/16-18 x 3/4
40 532 40 77-60 Plug, Case
8
9
872 27 05-05 Bolt, Carriage 5/16-1 8 x 5/8
532 19 98-79 Bolt
10 532 40 77-21 Housing, Auger
11 532 40 76-45 Bar, Scraper
12 532 18 40-95 Bracket, Corner Discharge
13 532 17 53-22 Base, Discharge Chute
14 819 11 15-07 Washer, Flat
41 532 40 77-61 Housing, Gearbox, RH
42 532 40 77-70 Seal, Oil
15 532 19 85-52 Washer, Lock 5/16
16 874 95 05-12 Screw, Hex Head 5/16-18 x 3/4
17 532 40 56-37 Grease Fitting
43 532 40 77-62 Bushing, Flange, 1"
44 532 18 92-82 Key, Square 1/4 x 1/4 x 7/8
45 532 40 77-63 Gear, Worm
18 532 17 95-82 Screw, Hex Head 5/16 x 1
19 873 80 04-00 Nut, Hex Lock 1/4-20
20 532 19 85-41 Nut, Hex Lock 5/16-18
21 532 40 13-47 Washer, Flat 5/16
22 532 40 78-34 Skid Plate, Heavy Duty
24 532 12 86-38 Wing Nut
25 872 27 05-06 Bolt, Shoulder 1/4-20
26 532 18 79-25 Bearing
27 532 17 46-97 Washer, Thrust, 1"
28 532 19 86-36 Bolt, Shear
46 532 40 77-64 Shaft, Auger
47 532 40 77-65 Housing, Gearbox, LH
48 532 18 41-05 Impeller Assembly
49 874 78 04-26 Screw, Hex Head 1/4-20 x 1-5/8
50 532 40 77-66 Gasket, Gearbox
51 532 18 42-05 Pin, Roll 3/16 x 1-1/8
52 532 40 76-51 Bar, Drift
53 532 19 86-48 Bolt, Hex Head
54 532 19 87-09 Stop
55 532 19 86-38 Spacer
30 532 40 77-22 Auger Assembly, RH
56 532 18 06-84 Multi-Wrench
57 532 19 67-10 Gearbox Assembly
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your lawn mower and void your warranty.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
CONTROL PANEL / DISCHARGE CHUTE
SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17
2
1
19
2
2
22
2
6
23
26
3
22
27
28
4
5
20
29
25
6
9
10
23
27
11
16
18
7
30
12
14
17
31
3
8
13
15
8
22
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
CONTROL PANEL / DISCHARGE CHUTE
SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17
KEY PART
NO. NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
532 18 33-34 Knob, Lever
817 50 10-10 Screw #10-24 x 5/8
532 19 84-75 Control Assembly, Deflector
873 80 06-00 Nut, Lock 3/8-16
819 13 13-16 Washer, Flat 3/8
532 40 49-74 Control Assembly, Chute Rotater
532 40 76-43 Support, Pivot
532 15 00-78 Screw, Hex Head 5/16-18 x 3/4
532 18 45-05 Spring, Deflector
10 532 17 98-29 Bolt, Shoulder
11 532 17 92-46 Washer, Friction, Nylon
12 532 19 17-30 Nut, Lock 1/4-20
13 872 25 05-05 Bolt, Carriage 5/16-18
14 532 75 11-53 Nut, Lock 5/16-18
15 532 40 76-50 Chute Assembly
16 532 18 41-13 Deflector Assembly
17 532 17 91-45 Seal, Deflector
18 532 12 84-15 Rivet, Blind
19 532 18 33-33 Knob, Speed Control Lever
20 872 27 05-06 Bolt, Carriage 5/16-18 x 3/4
22 874 04 10-24 Screw #10-24 x 1-1/2
23 532 19 24-49 Control Assembly, Power Steering
25 532 19 85-41 Nut, Lock 5/16-18
26 532 19 84-74 Lever Assembly, Speed Control
27 532 16 96-75 Retainer, Hairpin
28 532 18 04-45 Rod, Upper, Speed Control
29 532 18 77-16 Rod, Lower, Speed Control
30 532 19 27-10 Clamp, Clean-Out Tool
31 532 19 21-99 Tool, Clean-Out
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your lawn mower and void your warranty.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
HANDLES
SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17
2
41
5
49
12
28
7
5
5
6
4
15
4
36
8
45
42
9
34
46
28
1
37
44
13
48
4
43
34
15
19
11
4
17
5
15
16
49
46
35
18
33
35
41
22
11
21
10
22
15
23
47
20
12
14
24
25
27
16
24
17
32
31
26
29
31
27
32
30
38
39
40
24
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
HANDLES
SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17
KEY PART
NO. NO.
DESCRIPTION
1
2
4
5
6
7
8
9
532 40 76-49 Lever, Auger Control, RH
532 40 76-48 Lever, Traction Drive Control, LH
532 17 88-88 Bushing, Flange
532 16 96-75 Retainer, Hairpin
817 06 04-08 Screw, Hex Head
532 17 86-52 Rod, Interlock
532 19 95-76 Arm, Impeller Rod
532 19 95-75 Arm, Traction Rod
10 532 19 95-31 Panel, Control
11 874 78 05-24 Screw, Hex Head 5/16-18 x 1-1/2
12 874 78 05-12 Screw, Hex Head 5/16-18 x 1-3/4
13 532 40 78-36 Handle Tube, LH
14 532 40 78-35 Handle Tube, RH
15 532 75 11-53 Nut, Lock 5/16-18
16 819 13 13-16 Washer, Flat 3/8
17 532 17 88-99 Knob, Handle
18 532 18 45-94 Rod, Auger Control
19 532 19 30-81 Rod, Traction Control
20 532 18 04-28 End, Control Rod
21 873 35 05-00 Nut, Hex, Jam 5/16-18
22 872 12 06-18 Bolt, Carriage 3/8-16 x 2-1/4
23 532 18 40-87 Handle Tube, Lower
24 532 18 04-47 Sleeve, Spring
25 532 18 09-26 Spring, Traction Drive
26 532 17 86-69 Spring, Auger Control
27 817 00 06-16 Screw, Hex Head 3/8-16 x 1
28 532 19 85-59 Bushing, Pivot Lever
29 532 40 57-81 Switch, Heated Handle Grips
30 532 40 58-79 Console, Panel
31 532 17 52-62 Screw, Hex Head, Tapping #10-24 x 1-1/4
32 532 18 44-71 Screw, Hex Head, Tapping #10-24 x 1/2
33 532 19 95-77 Latch, Interlock
34 532 18 35-18 Bolt, Shoulder
35 532 06 80-38 Nut, Lock 1/4-20
36 532 17 88-31 Spring, Torsion
37 532 19 38-85 Spring, Interlock
38 532 17 86-66 Headlight, Halogen (Includes Bulb)
- - 532 40 16-20 Bulb, Halogen
39 532 17 86-68 Bezel, Headlight
40 532 40 56-99 Harness, Headlight (Halogen)
41 532 17 87-75 Pop Rivet
42 532 19 95-78 Lever, Interlock
43 532 19 96-38 Rod, Latch, Interlock
44 532 19 63-38 Rod, Arm, Interlock
45 532 70 02-79 Clip
46 532 17 92-46 Washer
47 532 19 69-43 Mounting Bracket, Handle, RH
48 532 19 69-44 Mounting Bracket, Handle, RH
49 532 40 58-17 Grip, Handle, Heated
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your lawn mower and void your warranty.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
DRIVE
SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17
5
2
1
4
4
1
2
7
5
4
2
1
2
8
1
10
9
2
27
2
14
5
13
22
12
16
21
24
20
41
18
7
17
32
4
15
23
18
44
6
19
2
5
4
25
15 29
43
34
11
22
41
33
26
28
36
38
39
40
31
30
22
26
33
37
35
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
DRIVE
SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17
KEY PART
NO. NO.
DESCRIPTION
1
2
4
5
6
7
8
9
532 19 85-84 Screw, Hex Head 5/16-18 x 3/4
532 75 11-53 Nut, Lock 5/16-18
532 19 85-84 Screw, Hex Head 5/16-18 x 1/2
532 18 00-17 Bearing, Flange
532 18 01-34 Shaft, Auxiliary
532 17 92-70 Spacer, Plate
532 19 29-07 Plate, Auxiliary
532 18 00-82 Gear, Intermediate (12/58)
10 532 18 00-65 Gear, Pinion
11 532 18 77-14 Rod, Clutch
12 532 18 00-66 Shaft, Long, Hex
13 532 17 88-07 Pin, Pivot
14 532 18 40-80 Lever, Shifter / Wheel
15 532 17 53-44 Trunnion Bearing Assembly
16 532 18 78-57 Bracket, Pivot, Shift
17 532 17 98-31 Ring, Rubber Wheel
18 532 19 95-09 Plate, Rubber Wheel
19 873 93 05-00 Nut, Lock 5/16-18
20 532 17 86-13 Hub, Rubber Wheel
21 874 76 05-14 Screw, Hex Head 5/16-18 x 7/8
22 532 08 51-79 Retainer, Hairpin
23 532 18 01-35 Spring, Bias
24 532 18 00-81 Gear, Axle (58 Teeth)
25 532 17 86-95 Pin, Pivot Lever
26 532 19 77-63 Plate Assembly, Drive
27 532 40 43-07 Shaft, Axle
28 532 19 77-64 Shaft, Short Hex
29 532 18 40-77 Lever, Shifter Plate
30 532 18 40-76 Bracket, Shifter Support
31 872 27 05-05 Bolt, Carriage 5/16-18 x 5/8
32 532 18 92-82 Key, Square 1/4 x 1/4 x 7/8
33 532 18 89-09 Bearing, Flange
34 532 18 40-75 Plate, Drive Mounting
35 532 18 25-04 Spacer, Bearing
36 532 19 10-80 Pulley, Traction Drive
37 532 19 85-41 Nut, Lock 5/16-18
38 819 11 15-07 Washer, Flat
39 532 19 85-52 Washer, Lock 5/16
40 874 95 05-12 Screw, Hex Head 5/16-18 x 3/4
41 812 00 00-12 Ring, Retaining
43 532 17 90-95 Spring, Return
44 532 18 42-06 Pin, Roll
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your lawn mower and void your warranty.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
CHASSIS / ENGINE / PULLEYS
SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17
3
30
58
57
19
17
28
6
22
6
10
25
21
26
23
4
31
10
6
24
21
29
27
16
18 20
31
36
37
2
9
7
1
39
55
42
12
43
32
33
7
11
8
6
13
38
41
44
15
14
41
34
45
44
35
50
52
51
11
49
48
11
46
47
47
28
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
CHASSIS / ENGINE / PULLEYS
SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17
KEY PART
NO. NO.
KEY PART
NO. NO.
DESCRIPTION
DESCRIPTION
1
2
3
532 18 10-44 Spring, Traction Idler
532 18 05-22 Pulley, Idler (2-1/4)
27 532 85 10-84 Screw, Hex Head 3/8-24 x 1-3/8
28 532 15 54-52 Guide, Belt
29 532 19 22-13 Belt Cover Assembly
(Includes Toolbox Cover)
- - -
Engine, Tecumseh, Model Number
LH358SA (For engine service and
replacement parts, call Tecumseh
Products at 1-800-558-5402)
30 532 17 88-30 Cover, Toolbox
31 532 40 05-24 Screw, Hex Head 1/4-20 x 1/2
32 532 17 92-56 Bolt, Shoulder 5/16-18
33 532 18 78-53 Bellcrank Shifter
34 532 19 85-80 Clevis Pin
35 532 40 54-85 Arm, Auger Control
36 873 80 05-00 Nut, Lock 5/16-18
37 532 18 40-86 Bellcrank
4
6
7
8
9
874 78 05-20 Screw, Hex Head 5/16-18 x 1-1/4
532 05 92-89 Washer, Flat
532 16 67-85 Nut, Jam, Lock 5/16-18
532 17 53-30 Pin, Idler Pivot
532 17 90-92 V-Belt, Traction Drive
10 532 19 85-52 Washer, Lock 5/16
11 532 19 85-84 Screw, Hex Head 5/16-18 x 1/2
12 532 17 92-59 Impeller Arm / Pad Assembly
13 532 08 51-79 Retainer, Hairpin
38 532 18 71-01 Link, Speed Control
39 532 19 21-10 Trunnion, Pivot Bracket
41 532 70 02-79 Hairpin, Cotter 3/32 x 1/2
42 532 17 90-65 Pin, Bellcrank
14 532 17 88-28 Spring, Brake
15 532 18 35-33 V-Belt, Impeller Drive
16 532 15 04-06 Screw, Hex Head 3/8-16 x 1-1/4
17 532 18 48-04 Arm, Idler
18 874 78 05-24 Screw, Hex Head 5/16-18 x 1-1/2
19 532 19 85-59 Bushing, Idler Pivot
43 532 18 40-85 Bracket, Bellcrank
44 817 00 06-16 Screw, Hex Head
45 532 18 40-74 Pivot Bracket, Impeller Idler Arm
46 532 18 40-84 Pan, Frame Bottom
47 871 02 05-12 Screw, Hex Head 5/16-18 x 3/4
48 532 18 11-56 Nut, Speed 5/16-18
49 532 40 76-42 Frame Assembly
50 532 18 80-02 Plate, Frame End
51 532 40 61-09 Shaft, Auger Control
52 532 05 70-79 Washer, Hardened
55 532 19 21-47 Ring, Crescent
20 532 18 05-23 Pulley, Idler (2-3/4)
21 874 61 05-16 Screw, Hex Head 5/16-18 x 1
22 532 17 93-71 Spacer, Engine Pulley
23 532 18 04-78 Pulley, Engine, Traction Drive
24 532 17 91-57 Pulley, Engine, Impeller Drive
25 532 40 00-26 Washer, Flat 3/8
26 532 85 02-63 Washer, Lock, Helical 3/8
57 811 05 05-00 Washer, Lock, External Tooth 5/16
58 532 19 85-63 Power Cord
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your lawn mower and void your warranty.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
WHEELS / DECALS
SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17
18
14
27
10
30
15
32
13
10
20
12
17
19
11
11
7
2
28
8
28
26
22
29
31
11
25
4
7
24
23
9
4
33
21
3
4
1
4
34
24
3
22
29
25
21
33
2
23
14
28
30
26
18
10
28
15
12
27
11
16
19
34
11
20
32
13
1 13
2
4
12
9
8
6
7
5
11
10
3
30
1 13
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
WHEELS / DECALS
SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17
KEY PART
NO. NO.
DESCRIPTION
1
2
3
4
7
8
9
532 19 95-01 Wheel Assembly, 16", Power Steering, LH
532 15 54-43 Pin, Klik 1/4
532 40 51-61 Cover, Power Steering
532 18 44-71 Bolt, Shoulder #10-24 x 5/8
817 00 06-16 Capscrew, Hex Head, Flanged 3/8-16 x 1
532 18 78-59 Bracket, Steering Cable, RH
532 18 78-58 Bracket, Steering Cable, LH
10 817 60 04-06 Screw, Hex Head 1/4-20 x 3/8
11 532 19 85-84 Screw, Hex Head 5/16-18 x 1/2
12 532 40 60-57 Link, Steering Lever
13 532 40 78-37 Yoke, Steering
14 532 18 20-15 Pin, Steering Lever
15 532 19 95-18 Bellcrank
16 532 19 95-12 Bracket Assembly, LH Steering
17 532 19 95-11 Bracket Assembly, RH Steering
18 532 18 18-47 Pin, Steering Bellcrank
19 532 08 51-79 Retainer, Hairpin
20 532 18 41-97 Bracket, Steering
21 532 19 21-26 Driver, Wheel
22 532 18 24-66 Ring, Wire Retainer
23 532 18 76-22 Lobe, Wheel
24 532 19 49-41 Slide, Clutch
25 532 17 91-39 Spring, Clutch Slide
26 532 19 49-40 Lobe, Axle
27 532 18 92-82 Key, Square
28 532 17 46-97 Washer, Thrust (1")
29 532 17 98-30 Bearing, Axle
30 532 19 38-85 Spring, Return
31 532 19 95-02 Wheel Assembly, 16", Power Steering, RH
32 532 70 02-79 Clip, Retainer
33 812 00 00-45 Ring, Retaining
34 532 14 63-15 Screw, Hex Head 5/16-18 x 5/8
KEY PART
NO. NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
532 18 10-38 Decal, Danger
532 19 13-78 Decal, Husqvarna
532 18 10-34 Decal, Danger, Deflector
532 18 10-41 Decal, Danger
532 40 57-68 Decal, Husqvarna, 1130SBE
532 18 10-32 Decal, Instruction
532 15 57-98 Decal, Traction Lever
532 15 58-00 Decal, Auger Lever
532 18 10-36 Decal, Speed Control
10 532 18 37-29 Decal, Remote Deflector
11 532 18 39-07 Decal, LH Trigger
12 532 18 39-05 Decal, RH Trigger
13 532 15 57-94 Decal, Husqvarna, Crown
- - 532 40 57-35 Owner’s Manual, English
- - 532 40 80-93 Owner's Manual, French
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your lawn mower and void your warranty.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
532 40 57-35 Rev. 1 08.04.06 BY
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|