Models:
Operators Manual
968999250 / Z4818BIA
Please read these instructions carefully and make
sure you understand them before using the machine.
MANUAL NO. 539109797 REV. IR (09/18/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
SYMBOLS & DECALS ......................... 4
Air Screen & Air Filter ................. 26
Oil Filter ...................................... 26
Spark Plugs ................................ 26
Fuel Filter.................................... 26
Cleaning ..................................... 26
SERVICE AND ADJUSTMENT............. 27
Mower ......................................... 27
Deck Level.................................. 27
Deck Belt Replacement ............. 28
SAFETY INSTRUCTIONS.................... 5
General use and saftey rules...... 5
Driving on slopes ........................ 7
Children safety............................ 8
Service safety............................. 8
Transportation ............................ 10
SPECIFICATIONS................................. 11
ASSEMBLY ........................................... 12
Tools Required............................ 12
Unpacking................................... 12
Seat Attachment ......................... 12
Control Lever Attachment ........... 12
Check Tire Pressure .................. 14
Assembly Checklist .................... 14
OPERATION.......................................... 15
Controls ...................................... 15
Operation Instructions ................ 16-21
CUSTOMER RESPONSIBILITIES ...... 22
Maintenance Schedule ............... 22
Lubrication Chart ........................ 23
Tires ........................................... 23
Operator Presence System ....... 23
Blade Care ................................. 23
V-Belts ........................................ 25
Engine ........................................ 25
IZT (Integraded Zeroturn
Transaxle) Belt Replacement ..... 29
Seat Adjustment ......................... 30
Control Levers Adjustment ......... 30
Wheel Removal .......................... 30
Jump Starting Engine ................. 30
Battery Replacement.................. 31
Park Brake.................................. 31
TrackingAdjustment ................... 32
STORAGE ............................................. 33-34
TROUBLESHOOTING ......................... 35-36
WIRING SCHEMATIC ........................... 37
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS AND DECALS
N
R
Reverse
Neutral
Slow
Choke
Fast
Warning
Danger
Caution
Fuel
Ignition
Run
Mower
Mower
deck
engaged
deck
disengaged
Parking
brake
Stop
Start
Do not stand here
Do not tow or push mower
unless you engage the IZT
(Intergraded Zeroturn
Do not put pressure on
drive levers.
Read Operator’s Manual.
Transaxle) bypass linkages
Battery acid is corrosive, explosive, and flammable.
Cutting
height
Do not touch rotating parts.
Shut off engine
Keep a
safe
distance
from the
machine.
& remove key
before perform-
ing any
maintenance or
repair work.
Use on
slopes no
greater
Read
Operator’s
Manual
No passen-
gers
than 10°
Severing
of fingers
& toes.
Do not open
or remove
safety
shields while
engine is
running.
Careful
Careful going
forward,
watch for
Whole
body
exposure
to thrown
objects.
backing up,
watch for
other people.
other people.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Safety Instructions
These instructions are for your safety. Read them carefully.
WARNING!
This symbol means that important safety instructions need to be emphasized.
It concerns your safety.
General Use
•
Read all instructions in this operator’s
manual and on the machine before starting
it. Ensure that you understand them and
then abide by them.
•
Learn how to use the machine and its
controls safely and learn how to stop quickly.
Also learn to recognize the safety decals.
•
•
Only allow the machine to be used by adults
who are familiar with its use.
Make sure nobody else is in the vicinity of the
machine when you start the engine, engage
the drive, or run the machine.
8011-512
Read the operator’s manual before starting the
machine
•
•
•
Make sure animals and people maintain a
safe distance from the machine.
Stop the machine if someone enters the
work area.
Clear the area of objects such as stones,
toys, steel wire, etc. that may become
caught in the blades and thrown out.
•
Beware of the discharge deck and do not
point it at any one. Do not use the machine
without the discharge deck in place.
8011-513
•
•
•
•
Stop the engine and prevent it from start-ing
before you clean the discharge deck.
Clear the area of objects before mowing
Remember that the operator is responsible
for dangers or accidents.
Never take passengers. The machine is only
intended for use by one person.
Always look down and behind before and
during reversing maneuvers. Keep a look out
for both large and small obstacles.
•
•
Slow down before turning.
8011-520
Shut down the blades when not mowing.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
•
•
Be careful when rounding fixed objects, so
that the blades do not hit them. Never drive
over foreign objects.
WARNING!
Engine exhaust and certain
vehicle components contain
or emit chemicals considered
to cause cancer, birth defects,
or other reproductive system
damage. The engine exhaust
contains carbon monoxide,
which is a colorless, poisonous
gas. Do not use the machine
in enclosed spaces.
Only use the machine in daylight or in other
well-lit conditions. Keep the machine a safe
distance from holes or other irregularities in
the ground. Pay attention to other possible
risks.
•
Never use the machine if you are tired, if
you have consumed alcohol, or if you are
taking other drugs or medication that can
affect your vision, judgment, or
coordination.
•
•
Beware of traffic when working near or
crossing a road.
Never leave the machine unsupervised with
the engine running. Always shut down the
blades, pull back the parking brake, stop the
engine, and remove the ignition key before
leaving the machine.
•
Never allow children or other persons not
trained in the use of the machine to use or
service it. Local laws may regulate the age
of the user.
8011-518
WARNING!
When using the machine, approved personal protective equipment shall be
used. Personal protective equipment cannot eliminate the risk of injury but it
will reduce the degree of injury if an accident does happen. Ask your retailer
for help in choosing the right equipment.
•
•
Make sure that you have first aid equipment
close at hand when using the machine.
Never use the machine when barefoot.
Always wear protective shoes or boots,
preferably with steel toecaps.
•
•
Always wear approved protective glasses or
a full visor when assembling or driving.
Never wear loose clothing that can get
caught in moving parts.
8011-292
Personal protective equipment
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Driving on Slopes
Driving on slopes is one of the operations where
the risk is greatest that the driver will lose control or
the machine will tip over, which can result in
serious injury or death. All slopes require extra
caution. If you cannot reverse up a slope or if you
feel unsure, do not mow the slope.
Do as follows
•
Remove obstacles such as stones,
tree branches, etc.
•
•
Mow up and down, not side-to-side.
Never drive the rider on terrain that slopes more
than 10°.
•
Avoid starting or stopping on a slope. If the tires
begin to slip, shut down the blades and drive
slowly down the slope.
•
•
•
Always drive evenly and slowly on slopes.
8003-004
Mow up and down, not side-to-side
Make no sudden changes in speed or direction.
Avoid unnecessary turns on slopes, and if it
proves necessary, turn slowly and gradually
downward, if possible.
•
Watch out for and avoid driving over furrows,
holes, and bumps. On uneven terrain, the
machine can tip more easily. Long grass can
hide obstacles.
•
•
•
Drive slowly. Use small movements of the
steering controls.
Be extra cautious with any additional equipment,
which can alter the machine’s stability.
Do not mow near verges, ditches, or banks. The
machine can suddenly spin around if a wheel
goes over the edge of a drop or ditch, or if an
edge gives way.
•
•
•
•
Do not mow wet grass. It is slippery, and the tires
can lose their grip, so that the machine slides.
8011-519
Be extra cautious when driving on slopes
Try not to stabilize the machine by putting a foot
on the ground.
When cleaning the chassis, the machine may
never be driven near verges or ditches.
Avoid starting or stopping on a slope. If tires
lose traction, disengage the blades and
proceed slowly straight down the slope.
•
•
If machine stops while going uphill, disen-
gage blades and back down slowly.
Do not turn on slopes unless necessary, and
then, turn slowly and gradually downhill, if
possible.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Children
•
Serious accidents may occur if you fail to be
on guard for children in the vicinity of the
machine. Children are often attracted to the
machine and mowing work. Never assume
that children will stay put where you last saw
them.
•
Keep children away from the mowing area
and under close supervision by another
adult.
•
•
Keep an eye out and shut off the machine if
children enter the work area.
Before and during a reversing maneuver,
look backward and downward for small
children.
8011-517
Never allow children to operate the machine
•
Never allow a child to ride with you. They can
fall off and injure themselves seriously or
prevent risk-free maneuvering of the
machine.
•
•
Never allow children to operate the machine.
Be particularly cautious near corners,
bushes, trees, or other objects that block
your view.
WARNING!
The engine must not be started when the driver’s floor plate or any protective
plate for the mower deck’s drive belt is removed.
•
Stop the engine. Prevent the engine from
starting by removing the ignition key before
making any adjustments or performing
maintenance.
•
•
Never fill the fuel tank indoors.
Fuel and fuel fumes are poisonous and
extremely flammable. Be especially cautious
when handling fuel, as carelessness can
result in personal injury or fire.
•
•
Only store fuel in containers approved for the
purpose.
Never remove the fuel tank cap and never fill
the fuel tank while the engine is running.
8011-516
Never fill the fuel tank indoors
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
•
•
•
•
Allow the engine to cool before refueling. Do
not smoke. Do not fill fuel in the vicinity of
sparks or open flames.
WARNING!
If leaks arise in the fuel system, the engine
must not be started until the problem has been
resolved.
The engine, the exhaust system,
and the hydraulic system’s
components become very warm
during operation.
Store the machine and fuel in such a way that
there is no risk of leaking fuel or fuel vapor
leading to damages.
Risk for burns if touched.
Check the fuel level before each use and leave
space for the fuel to expand, because the heat
from the engine and the sun may otherwise
cause the fuel to expand and overflow.
•
Avoid overfilling. If you spill fuel on the machine,
wipe up the spill and wait until it has evaporated
before starting the engine. If you have spilled
fuel on your clothing, change your clothing.
WARNING!
The battery contains lead and
lead compounds, chemicals
that are considered to cause
cancer, birth defects, and
other reproductive system
damage. Wash your hands
after touching the battery.
•
•
Allow the machine to cool before taking any
actions in the engine compartment.
Be very careful when handling battery acid.
Acid on skin can cause serious corrosive
burns. If you spill battery acid on your skin,
rinse immediately with water.
•
•
Acid in the eyes can cause blindness, contact
a doctor immediately.
Be careful when servicing the battery.
Explosive gases form in the battery. Never
perform maintenance on the battery when
smoking or near open flames or sparks. The
battery can explode and cause serious injury/
damage.
•
•
Ensure that nuts and bolts, especially the
fastening bolts for the blade attachments, are
properly tightened and that the equipment is in
good condition.
Do not modify safety equipment. Check
regularly to be sure it works properly. The
machine must not be driven with defective or
unmounted protective plates, protective
cowlings, safety switches, or other protective
devices.
8011-563
Do not smoke when performing maintenance on
the battery. The battery can explode and cause
serious injury/damage
•
Do not change the settings of governors and
avoid running the engine with overly high
engine speeds. If you run the engine too fast,
you risk damaging the machine components.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
•
•
Never use the machine indoors or in spaces
lacking proper ventilation. The exhaust fumes
contain carbon monoxide, an odorless,
poisonous, and lethal gas.
Stop and inspect the equipment if you run over
or into anything. If necessary, make repairs
before starting.
•
•
Never make adjustments with the engine
running.
The machine is tested and approved only with
the equipment originally provided or
recommended by the manufacturer.
•
The blades are sharp and can cause cuts and
gashes. Wrap the blades or use protective
gloves when handling them.
8011-515
Never drive the machine in an enclosed space
•
•
Check the parking brake’s functionality
regularly. Adjust and service as necessary.
The mulch deck shall only be used when
higher quality mowing is desired in familiar
areas.
•
Reduce the risk of fire by removing grass,
leaves, and other debris that may have
accumulated on the machine. Allow the
machine to cool before putting it in storage.
Transport
•
The machine is heavy and can cause serious
crushing injuries. Be extra cautious when it is
loaded on or unloaded from a vehicle or trailer.
8011-514
Clean the machine regularly
•
Use an approved trailer to transport the
machine. Activate the parking brake, turn off
the fuel supply, and fasten the machine with
approved fastening devices, such as bands,
chains, or ropes, when transporting.
IMPORTANT INFORMATION
The parking brake is not sufficient to
lock the machine in place during
transport. Ensure that the machine is
well fastened to the transport vehicle.
Reverse the machine onto the transport
vehicle to avoid tipping it over.
•
Check and abide by local traffic regulations
before transporting or driving the machine on
any road.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
GASOLINE CAPACITY
5.6 GALLONS
AND TYPE
UNLEADED REGULAR
OIL TYPE (SPI-SF-SJ):
SEE YOUR ENGINE
OWNERS MANUAL
SPARK PLUG:
SEE ENGINE MANUAL
GROUND SPEED (MPH):
FORWARD: 0 - 5.5
REVERSE: 0 - 2.5
TIRE PRESSURE:
CHARGING SYSTEM:
BATTERY:
FRONT: 15 PSI
REAR: 15 PSI
BRIGGS & STRATTON 16AMP
@ 3600 RPM
MIN. CCA: 300
CASESIZE: 5 1/4W X 7 3/4 L X 6 T
BLADE BOLT TORQUE:
45-55 FT./LBS.
CUSTOMER RESPONSIBILITIES
•
•
Read and observe the safety rules.
CONGRATULATIONS on your purchase of a
new mower. It has been designed, engineered
and manufactured to give you the best possible
dependability and performance.
Should you experience any problem you cannot
easily remedy, please contact your nearest
authorized service center/ department. We
have competent, well-trained technicians and
the proper tools to service or repair this mower.
Please read and retain this manual. The in-
structions will enable you to assemble and
maintain your mower properly. Always observe
the "SAFETY RULES”.
Follow a regular schedule in maintaining,
caring for and using your mower.
Follow the instructions under "Customer
Responsibilities” and "Storage” sections of
this owner’s manual.
•
WARNING
This mower is equipped with an internal
combustion engine and should not be used
on or near any unimproved forest-covered,
brush-covered or grass-covered land un-
less the engine’s exhaust system is
equipped with a spark arrester meeting
applicable local or state laws (if any). If a
spark arrester is used, it should be main-
tained in effective working order by the op-
erator.
A spark arrester for the muffler is available
through your nearest authorized engine service
center/department.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Your new mower has been assembled at the factory with the exception of those parts left un-
assembled for shipping purposes. To ensure safe and proper operation of your mower, all
parts and hardware you assemble must be tightened securely. Use the correct tools as
necessary to insure proper tightness.
TOOLS REQUIRED
FOR ASSEMBLY
1. 9/16" wrench or 9/16" socket w/ drive
ratchet
2. Tire pressure gauge
3. Nail bar or claw hammer
4. Wire snips
When right or left hand is mentioned in this
manual, it means when you are in the operating
position (seated).
TO REMOVE THE MOWER
FROM CRATE
UNPACK CRATE
•
Using the nail bar or hammer, remove the
top of the crate first. Then remove the
sides of the crate and place these out of
the way. Be careful of any exposed nails
or staples.
•
•
•
Remove the plastic bag that covers the
mower.
Using the wire snips, cut any plastic ties
that are holding the mower to the crate.
Remove the seat off of the front of the
mower and place in a safe location.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
BEFORE REMOVING THE
MOWER FROM THE SKID
ATTACH SEAT (See Fig. 1)
The seat position should be adjusted forward or
backward so that the operator can comfortably
reach the deck lift pedal and safely operate the
mower. See "Service and Adjustment" Section
of this manual.
1
2
•
•
Remove protective wrap from the seat.
Remove the three prong knobs and
washers from the seat and place in the
storage area in the right side console.
Raise the seat pan up so that the bottom
can be easily accessed.
3
•
•
CZ-1
Securing one of the three prong knobs
and washers, insert it thru the seat pan
slot and into the corresponding threaded
hole in the seat bottom.
FIGURE 1
1. SEAT PAN
2. KNOBS
3. WIRE HARNESS
•
•
Repeat for the other three holes.
Tighten the three prong knobs in the
approximate position desired for the
seat.
•
Connect the wiring harness to the seat
switch.
Adjustments may be required to position the
seat in the desired position. Refer to the
"Service and Adjustment" section of this
manual.
ATTACH CONTROL LEVERS (See Fig. 2)
•
Using the 9/16" wrench or socket and
ratchet, remove the bottom hex bolt and
spring washer from the control arm.
Rotate the control lever up until the bolt
and spring washer can be placed thru
the slot in the bottom of the control lever
and threaded back into the control arm.
Center the hex bolt in the slot on the
control lever. Using the wrench or
ratchet, tighten both the top and bottom
hex bolts.
1
•
2
•
•
3
Repeat on opposite side of the mower.
Adjustments may be required to get uniform
positioning of the control lever. Refer to the
"Service and Adjustment" section of this manual.
4
CZ-2
FIGURE 2
1. CONTROL LEVER
2. CONTROL ARM
3. HEX BOLTS
NOTE: You may now roll or drive the mower off
of the skid. Follow the appropriate instruction
below to remove the mower from the skid.
4. NEUTRAL SLOT
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
TO ROLL THE MOWER OFF OF THE SKID
(See Operation section for location and
function of controls
•
Move to the rear of the mower, and place
the IZT (Integraded Zeroturn Transaxle)
bypass linkages into the bypass position
to disengage the IZT’s (See “TO
TRANSPORT” in the Operation section
of this manual).
•
Sitting on the mower, press the deck lift
pedal in to the highest cutting position.
Release park brake lever.
Roll the mower forward or backward off
of the skid.
•
•
TO DRIVE THE MOWER OFF OF THE
SKID (See Operation section for location
and function of controls)
WARNING
Before starting, read, understand and
follow all instructions in the Operation
section of this manual. Be sure the mower
is in a well-ventilated area. Be sure the area
in front of the mower is clear of other people
and objects.
•
•
•
Be sure all of the above assembly
steps have been completed.
Check engine oil level and fill fuel
tank with gasoline.
Place the IZT(Integraded Zeroturn
Transaxle) bypass linkages into the
drive position (See “TRANSPORT” in
the Operation section of this manual).
Sit on the seat in the operating
position, set the park brake lever to
the on position.
•
•
•
Rotate the control levers outward
into the neutral slot.
Press forward on the deck lift pedal
to raise the deck into the highest
cutting position.
•
•
Place the throttle control into the
choke position.
Start the engine. After the engine
has started, move the throttle control
to the idle position.
•
•
Release the park brake.
Move the control levers into the
operate position.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
•
•
Slowly move the control levers
forward and slowly drive the mower
off of the skid.
Return the control levers back to the
neutral position.
•
•
Apply the park brake.
Turn the ignition key to the “OFF”
position.
CHECK THE TIRE PRESSURE
Correct tire pressure is important for best cutting
performance.
•
Check the tire pressure and adjust
accordingly. Refer to the
“SPECIFICATIONS” section in this
manual.
CHECKLIST
PLEASE REVIEW THE FOLLOWING
CHECKLIST
•
All assembly instructions have been
completed
•
•
No remaining loose parts in crate
Seat is adjusted properly and securely
fastened
•
•
All tires are properly inflated
Check wiring. See that all connections
are still secure, and wires are properly
clamped.
•
Before driving the mower, be sure the
IZT(Integraded Zeroturn Transaxle)
bypass linkages are in the drive position.
WHILE LEARNING HOW TO USE
YOUR MOWER, PAY EXTRA
ATTENTION TO THE FOLLOWING
ITEMS:
•
•
Engine oil is at proper level
Fuel tank is filled with fresh, clean,
regular unleaded gasoline. Check your
engine manual for fuel requirements.
Become familiar with all controls – their
location and function. Operate them
before you start the engine.
Become familiar with unit operation on a
flat and level area with the mower deck
shut off.
Be sure the brake system is in a safe
operating condition. If adjustment is
needed see Service and Adjustment
section.
•
•
•
15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
CONTROLS
3
3
1
5
8
7
9
CZ-5
10
CZ-3
4
2
6
CZ-10
CZ-6
FIGURE 3
6. IZT (Integraded Zeroturn
1. PTO SWITCH – Used to engage or
Transaxle)BYPASS LINKAGES –
Bypasses IZT’s for pushing or pulling
mower.
disengage the deck blades.
2. FOOT PEDAL – Used to raise, lower and
select various cutting heights of the deck.
7. IGNITION SWITCH – Used to start or stop
the engine.
3. CONTROL LEVERS – Sets the speed of
the mower in both forward and reverse
directions and turns the mower.
8. PARKING BRAKE LEVER – Engages
and disengages the park brakes.
4. CHOKE CONTROL – Used when starting
9. TENSION RELIEF LEVER – Used to
release the belt tension on the deck belt for
ease in removing or replacing the belt.
a cold engine.
5. THROTTLE CONTROL – Used to control
Engine Speed.
10. HOUR METER – Indicates hours of
operation.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
HOW TO USE YOUR MOWER
TO SET PARKING BRAKE (See Fig. 3)
Your mower is equipped with an operator
presence system. When the engine is running,
any attempt by the operator to leave the seat
without first setting the park brake will shut off
the engine.
•
Pull park brake lever up to engage the
park brake. Make sure the lever is
secured to the right.
DECK BLADES
•
To stop the deck blades, press down on
the PTO Switch into the disengaged
position.
ENGINE
•
Move throttle control to slow position.
NOTE: Failure to move the throttle control to
slow position and allow engine to idle before
stopping may cause engine to “backfire”.
•
Turn ignition key to “OFF” position and
remove key. Always remove key when
leaving the mower to prevent
unauthorized use.
•
Never use choke to stop engine.
IMPORTANT: LEAVING THE IGNITION
SWITCH INANY POSITION OTHER THAN
“OFF” WILL CAUSE THE BATTERY TO BE
DISCHARGED, (DEAD).
WARNING
Always stop mower completely before
leaving the operators position; to empty a
grass catcher, etc.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO USE THROTTLE CONTROL (See Fig. 3)
Always operate engine at full throttle. The
Throttle control is equipped with a choke detent.
Pressing the throttle control all of the way
forward will choke the engine. For full throttle,
press throttle control forward until you feel
resistance.
•
Operating engine at less than full throttle
reduces the battery charging rate
Full throttle offers the best mower
performance.
•
TO USE CHOKE CONTROL (See Fig. 3)
Use choke control whenever you are starting a
cold engine. Do not use to start a warm engine.
•
•
To choke, pull up on the choke knob.
To take out of choke, push down on the
choke knob.
Motion Control Lever Pattern
(Right Side)
TO MOVE FORWARD AND BACKWARD
(See Fig. 4)
3
IMPORTANT: CONTROL LEVERS RETURN
TO NEUTRAL WHEN RELEASED. THIS MAY
CAUSE A SUDDEN STOP OF THE MOWER.
1
FRONT OF
MOWER
2
The direction and speed of movement is
controlled by the control levers on either side of
the mower.
4
FIGURE 4
1. FORWARD
2. NEUTRAL
3. NEUTRAL SLOT
NEUTRAL LOCK
4. REVERSE
The left lever controls the flow of oil in the left IZT
(Integraded Zeroturn Transaxle) to the left wheel.
The right lever controls the flow of oil in the right
IZT to the right wheel.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
NOTE: To begin motion the operator must be in
the seat and the parking brake disengaged
before the motion control levers can be moved
from the neutral slots or the engine will kill. Fig. 4
and 4A.
1
2
By moving the levers an equal amount forward
or back the machine will move in a straight line
in that direction. Fig. 4 and 4A
3
Movement of either lever forward will cause the
right or left wheel to rotate in a forward direction.
To stop movement pull both levers into the
neutral position.
4
To turn right while moving in a forward direction
pull the right lever back towards the neutral
position, this will slow the rotation of the right
wheel and cause the machine to turn in that
direction.
5
6
CZ-7
To turn left while moving in a forward direction
pull the left lever back towards the neutral
position, this will slow the rotation of the left
wheel and cause the machine to turn in that
direction.
FIGURE 4A
1. FORWARD
2. REVERSE
3. CONTROL LEVER
4. HEX NUTS & WASHERS
5. CONTROL ARM
6. NEUTRAL SLOT
To zero turn pull one lever back beyond neutral
while holding the other slightly ahead of neutral.
NOTE: The direction of the zero turn will be
determined by which lever is pulled back beyond
neutral. Thus left lever back, left zero turn and
opposite for right zero turn.
Use extra care when using this maneuver
the machine can spin very rapidly if one
lever is positioned too far ahead of the
other.
CAUTION
DO NOT apply excessive force to control
levers or use to assist in dismounting unit.
Misuse will result in bent control levers.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO ADJUST THE DECK CUTTING
HEIGHT (See Fig. 5)
The deck cutting height is obtained by pressing
the foot pedal forward to lift the deck. To lower
the deck, you apply pressure to the top side of
the foot pedal and allow it to pivot while allowing
the lift arm to rotate to the rear of the unit. To
stop in a desired cutting position, rotate the foot
pedal down into the notch in the height plate.
The cutting height range is from 1 1/2" to 4 1/2"
in 1/2" increments. The heights are measured
from the ground up to the blade tip with the
engine not running.
1
2
3
•
The average lawn should be cut to 2 1/2"
during the cool season and to over 3"
during the hot months. For healthier and
better looking lawns, mow often and after
moderate growth.
CZ-8
FIGURE 5
1. FOOT PEDAL
2. LIFT ARM
3. HEIGHT PLATE
•
For best cutting performance, grass over
6 inches in height should be mowed
twice. Make the first cut relatively high;
the second to the desired height.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO ADJUST ANTI-SCALP
ROLLERS (See Figure 6)
1
Anti-scalp rollers are properly adjusted when
they are just slightly off of the ground when the
deck is at the desired cutting height in the
operating position. Anti-scalp rollers then keep
the deck in the proper position to help prevent
scalping in most terrain conditions.
NOTE: Adjust Anti-scalp rollers with the mower
on a flat level surface.
CZ-9
•
Adjust the deck to the desired cutting
height (see “TO ADJUST DECK
CUTTING HEIGHT” in the operation
section of this manual).
FIGURE 6
1. ANTI-SCALP ROLLER
•
Using a 3/4" wrench and a 9/16" wrench,
remove the nut and shoulder bolt from
the anti-scalp roller.
•
•
•
•
Lower the anti-scalp roller to the ground,
and raise it up to the next highest hole.
Replace and tighten the nut and shoulder
bolt.
Be sure to adjust all of the anti-scalp
rollers to the same position.
Be sure to readjust the anti-scalp rollers
if the cutting height is changed.
IMPORTANT: THE ANTI-SCALP ROLLERS
MUST NOT BE USED FOR GAUGE WHEELS
OR THE ROLLER AND DECK MAY BE
DAMAGED.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO OPERATE MOWER
Your mower is equipped with an operator
presence system. When the engine is running,
any attempt by the operator to leave the seat
without first setting the park brake will shut off
the engine.
•
•
Select desired height of cut.
Start deck blades by pulling the PTO
switch up into the engaged position.
To stop the deck blades, press down on
the PTO Switch into the disengaged
position.
•
WARNING
Do not operate the deck without either
the entire grass catcher, mulch kit or dis-
charge chute installed.
TO OPERATE ON HILLS
WARNING
Do not drive up or down hills with slopes
greater than 10 degrees. And do not drive
across any slopes.
•
•
The slowest speed possible should be
used before starting up or down hills.
Avoid stopping or changing speed on
hills.
•
If stopping is absolutely necessary, pull
drive levers into the neutral position and
push to the outside of the unit and
engage the park brake.
IMPORTANT: Control levers return to neutral
when released. This may cause a sudden stop
of the mower.
•
•
To restart movement, release the park
brake.
Pull the control levers back to the center
of the mower and press forward to
regain forward motion.
•
Make all turns slowly.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO TRANSPORT (See Fig. 7)
When pushing or pulling the mower, be sure to
engage the IZT (Integraded Zeroturn Transaxle)
bypass linkages. The IZT bypass linkages are
located on the rear of the frame, below the rear
engine guard.
1
CAUTION
CZ-10
Do not tow this vehicle, it may cause dam-
age to the drive system.
FIGURE 7
1. IZT BYPASS LINKAGE
1
•
•
Raise the deck into the highest cutting
position.
Pull the IZT bypass linkages out and into
the slots and release so that it is held in
the bypass position.
•
To reengage the IZT’s to drive, reverse
the above procedure.
2
CZ-11
FIGURE 7A
1. HEAD INSIDE OF REAR DECK
2. IZT BYPASS LINKAGE IN DRIVE POSITION
WARNING
Do not tow any trailers, etc. with this mower.
They may jackknife or overturn causing
damage to the mower and possibly serious
injury to the operator.
1
2
CZ-12
FIGURE 7B
1. HEAD OUTSIDE OF REAR DECK
2. IZT BYPASS LINKAGE IN BYPASS POSITION
23
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL
•
The engine in your mower has been
shipped from the factory, already filled
with 10W-30 motor oil.
•
•
•
Check engine oil with the mower on level
ground.
Refer to you Engine Owners Manual for
correct oil level.
To change engine oil, see the Customer
Responsibilities section of this manual.
ADD GASOLINE
•
Fill fuel tank. Use fresh, clean, regular
unleaded gasoline with a minimum of 87
octane. (Use of leaded gasoline will
increase carbon and lead oxide deposits
and reduce valve life). Do not mix oil
with gasoline. Purchase fuel in
quantities that can be used within 30
days to ensure fuel freshness.
IMPORTANT: WHEN OPERATING IN
TEMPERATURES BELOW 32° F. (0° C.), USE
FRESH, CLEAN WINTER GRADE GASOLINE
TO HELP INSURE GOOD COLD WEATHER
STARTING.
CAUTION
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads
to separation and formation of acids dur-
ing storage. Acidic gas can damage the fuel
system of an engine while in storage. To
avoid engine problems, the fuel system
should be emptied before storage of 30
days or longer. Drain the gas tank, start
the engine and let it the run until the fuel
lines and carburetor are empty. Use fresh
fuel the next season. See Storage Instruc-
tions for additional information. Never use
engine or carburetor cleaners in the fuel
tank or permanent damage may occur.
WARNING
Fill to bottom of filler neck. Do not over
fill. Wipe off any spilled oil or fuel. Do
not store, spill or use gasoline near an
open flame.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO START ENGINE (See Fig. 3)
When starting the engine for the first time or if
the engine has run out of fuel, it will take extra
cranking time to move fuel from the tank to the
engine.
•
Be sure IZT (Integraded Zeroturn
Transaxle) bypass linkages are in the
drive position.
•
•
•
•
Sit on the seat in the operators position,
release park brake lever.
Check to be sure the PTO switch is
disengaged.
Move the throttle control to the choke
position.
For a warm engine start, the choke
control may not be needed
NOTE: Before starting, read the warm and cold
starting procedures below.
•
Insert key into the ignition and turn the
key clockwise to “START” position and
release the key as soon the engine
starts. Do not run the starter
continuously for more than 15 seconds
per minute. If the engine does not start
after several attempts, push the throttle
control into the choke position, wait a few
minutes and try again. If the engine still
does not start, move the throttle control
back into the fast position and retry.
WARM WEATHER STARTING (50° F and above)
•
When the engine starts, slowly pull the
throttle control back until the engine
begins to run smoothly. If the engine
starts to run roughly, press the throttle
control back forward to choke the engine
for a few seconds. Then continue to pull
the throttle control back to the fast
position.
•
The PTO switch and ground drive can
now be used. If the engine does not
accept the load, restart the engine and
allow it to warm up for one minute using
the choke as described above.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
COLD WEATHER STARTING (50° F and below)
When the engine starts, slowly pull the
•
throttle control back until the engine
begins to run smoothly. Continue to pull
back on the throttle control in small steps
allowing the engine to accept small
changes in speed and load, until the
throttle control is completely in the fast
position. If the engine starts to run
roughly, press the throttle control back
forward to choke the engine for a few
seconds. Then continue to pull the
throttle control back slowly to the fast
position. This may require an engine
warm up period from several seconds to
several minutes, depending on the
temperature.
MOWING TIPS
•
The cutting deck should be properly
leveled for best mowing performance.
See “TO LEVEL DECK” in the Service
and Adjustment section of this manual.
The left hand side of the deck should be
used for trimming.
Drive so that clippings are discharged
onto the area that has been cut. Have
the cut area to the right of the mower.
This will result in more even distribution
of clippings and a more uniform cut.
If grass is extremely tall, it should be
mowed twice to reduce load and possible
fire hazard from dried clippings. Make
first cut relatively high; second to desired
height.
•
•
•
•
Do not mow grass when it is wet. Wet
grass will plug the deck and leave
undesirable clumps. Allow grass to dry
before mowing.
•
Always operate engine at full throttle
when mowing to assure better mowing
performance and proper discharge of
material. Regulate ground speed by
going slow enough to allow proper deck
cutting performance as well as the
quality of cut desired. When operating
attachments, select a ground speed that
will suit the terrain and give best
performance of the attachment being
used.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
MAINTENANCE SCHEDULE
Before
each
use
EVERY
Before
8 Hours 25 Hours 50 Hours 100 Hours Season Storage
Check Brake Operation
Check Tire Pressure
X
X
X
X
Check Operator Presence and
Interlock Systems
X
X
Check for Loose Fasteners
Sharpen/Replace mower Blades
Lubrication Chart
5
X
X
X
X 3
X
X
X
Check Battery Level
4
X
Clean Battery and Terminals
Check V-Belts
X
Check Engine Oil Level
Change Engine Oil (with oil filter)
Change Engine Oil (without oil filter)
CleanAir Filter
X
X
X
X
X1, 2
X1, 2
X 2
Clean Air Screen
2
X
Inspect Muffler/Spark Arrester
Replace Oil Filter
X
X 1, 2
2
Clean Engine Cooling Fins
Replace Spark Plug
X
X
X
X
2
Replace Air Filter Paper Cartridge
Replace Fuel Filter
X
3 - Replace blades more often when mowing in sandy soil.
4 - Not required if equipped with maintenance-free battery.
5 - Tighten front axle pivot bolt to 35 ft./lbs. maximum.
DO NOT overtighten.
1 - change more often when operating under a heavy load or in high
ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
GENERAL RECOMMENDATIONS
The warranty on this mower does not cover
items that have been subjected to operator
abuse or negligence. To receive full value from
the warranty, operator must maintain mower as
instructed in this manual.
Some adjustments will need to be made periodi-
cally to properly maintain your mower.
All adjustments in the Service and Adjustments
section of the this manual should be checked at
least once each season.
•
Once a year you should replace the
spark plug, clean or replace air filter, and
check blades and belts for wear. A new
spark plug and clean air filter assure
proper air-fuel mixture and help your
engine run better and last longer.
BEFORE EACH USE
•
•
•
•
Check engine oil level.
Check brake operation.
Check tire pressure.
Check operator presence and interlock
systems for proper operation.
Check for loose fasteners.
•
28
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
LUBRICATION CHART
GREASE LUBE POINTS EVERY 25 HOURS.
CHECK TIRE AIR PRESSURE
FRONT TIRES - 15 PSI
REAR TIRES - 15 PSI
REFER TO ENGINE OPERATORS MANUAL
PRIOR TO SERVICING THE ENGINE.
IMPORTANT:DONOTOILORGREASETHEPIVOTPOINTSWHICHHAVESPECIALNYLONBEARINGS.
VISCOUS LUBRICANTS WILLATTRACTDUSTAND DIRTTHATWILLSHORTENTHE LIFE OFTHE SELF-
LUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POWDERED
GRAPHITETYPELUBRICANTSPARINGLY.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
TIRES
•
•
•
Maintain proper air pressure in all tires
(See "SPECIFICATIONS" section of this
manual).
Keep tires free of gasoline, oil, or insect
control chemicals which can harm
rubber.
Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
NOTE: To seal tire punctures and prevent flat
tires due to slow leaks, tire sealant may be
purchased from your local parts dealer. Tire
sealant also prevents tire dry rot and corrosion.
OPERATOR PRESENCE SYSTEM
Be sure the operator presence and interlock
systems are working properly. If your mower
does not function as described, repair the
problem immediately.
•
The engine should not start unless the
parking brake is engaged, the PTO
switch is disengaged (pressed down),
the operator is on the seat, and the
control levers are rotated to the outside
of the mower.
•
•
When the engine is running, any attempt
by the operator to leave the seat without
first setting the park brake should shut off
the engine.
When the engine is running and the PTO
switch is engaged, any attempt by the
operator to leave the seat without first
disengaging the PTO switch, should shut
off the engine.
•
•
When the engine is running and the
control levers are rotated in, any attempt
by the operator to leave the seat without
rotating the control levers out, should
shut off the engine.
The PTO switch should never engage
without the operator on the seat.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
BLADE CARE
For best results, mower blades must be kept
sharp. Replace bent or damage blades.
4
1
BLADE REMOVAL (See Fig. 8)
2
NOTE: Protect your hands with gloves and/or
wrap blade with heavy cloth.
•
Remove blade bolt by turning
counterclockwise.
3
•
Install new or resharpened blade with
stamped "THIS SIDE UP" facing deck
and cutter housing.
5
FIGURE 8
1. BLADE
2. CENTER HOLE
3. STAR
4. CUTTER HOUSING
IMPORTANT:TO ENSURE PROPERASSEMBLY,
CENTER HOLE IN BLADE MUST ALIGN WITH
STAR ON CUTTER HOUSING.
5. BLADE BOLT (SPECIAL)
•
Install and tighten blade bolt securely
(45-55 ft./lbs. torque).
IMPORTANT: SPECIAL BLADE BOLT IS HEAT
TREATED.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
TO SHARPEN BLADE (See Fig. 9)
WARNING
When it is necessary to raise the
mower for any repair or service, use
jackstands to provide adequate sup-
port. DO NOT rely on hydraulic or me-
chanical jacks
2
Care should be taken to keep the blade bal-
anced. An unbalanced blade will cause exces-
sive vibration and eventual damage to mower
and engine.
3
1
•
•
The blade can be sharpened with a file or
on a grinding wheel. Do not attempt to
sharpen while on the mower.
To check blade balance, you will need a
5/8" diameter steel bolt, pin, or a cone
balancer. (When using a cone balancer,
follow the instructions supplied with
balancer.)
FIGURE 9
1. BLADE
2. CENTER HOLE
3. 5/8” BOLT OR PIN
NOTE: Do not use a nail for balancing the blade.
The lobes of the center hole may appear to be
centered, but are not.
•
Slide blade on to an un-threaded portion
of the steel bolt or pin and hold the bolt or
pin parallel with the ground. If the blade
is balanced, it should remain in a
horizontal position. If either end of the
blade moves downward, sharpen the
heavy end until the blade is balanced.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
BATTERY
Your mower is equipped with a maintenance
free battery and does not need servicing.
However, periodic charging of the battery with an
automotive type battery charger will extend its
life.
•
•
•
Keep battery and terminals clean.
Keep battery bolts tight.
Recharge at 6-10 amperes for 1 hour
NOTE: Do not attempt to open or remove caps
or covers. Adding or checking level of electrolyte
is not necessary.
TO CLEAN BATTERYAND TERMINALS
Corrosion and dirt on the battery and terminals
can cause the battery to “leak” power.
•
•
Remove terminal guard.
Disconnect BLACK battery cable first,
then the RED battery cable and remove
the battery from the tractor.
Rinse the battery with plain water and
dry.
Clean terminals and battery cable ends
with wire brush until shiny.
Coat terminals with grease or petroleum
jelly
•
•
•
•
Reinstall battery (See “REPLACING
BATTERY” in the SERVICE AND
ADJUSTMENT section of this manual).
V-BELTS
Check V-belts for deterioration and wear after
100 hours of operation and replace if necessary.
The Belts are not adjustable. Replace belts if
they begin to slip from wear.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
ENGINE
LUBRICATION
Refer to you Engine Owners Manual
TO CHANGE ENGINE OIL (See Fig. 10).
•
•
•
Be sure the mower is on a level surface.
Oil will drain more freely when warm.
Place a suitable container under the right
rear corner of the rear of the mower.
Remove oil dipstick. Be careful not to
allow dirt to enter the engine when
changing oil.
Using the clear plastic tube included with
you mower, place it over the end of the
drain valve located on the right side of
your engine.
•
•
1
•
Place the other end of the tube thru the
2" diameter hole on the right side of the
rear deck.
2
CZ-13
•
•
Be sure container is located under this
area of the mower.
FIGURE 10
1. ENGINE OIL DRAIN
2. PLASTIC TUBE
Using a 10 mm wrench, turn the hex
head on the oil valve counter clockwise
until the oil is draining out of the tube.
After the oil has drained, turn the hex
head clockwise until it is tight (do not
over tighten).
•
•
•
Remove the plastic tube from the valve,
clean excess oil off of tube and store in a
safe place for the next use.
Refill engine with oil through the oil
dipstick tube. Pour slowly. Do not
overfill.
See Engine Owners Manual for type and
capacity of the oil.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
CLEAN AIR SCREEN
Air screen must be kept free of dirt and chaff to
prevent engine damage from overheating. Refer
to your engine manual for the proper cleaning
procedure.
CLEAN AIR INTAKE/COOLING AREAS
To insure proper cooling, make sure the grass
screen, cooling fins, and other external surfaces
of the engine are kept clean at all times.
Every 100 hours of operation (more often under
extremely dusty, dirty conditions), remove the
blower housing and other cooling shrouds. Clean
the cooling fins and external surfaces as neces-
sary. Make sure the cooling shrouds are rein-
stalled.
NOTE: Operating the engine with a blocked
grass screen, dirty or plugged cooling fins, and/
or cooling shrouds removed will cause engine
damage due to overheating.
AIR FILTER
Your engine will not run properly using a dirty air
filter. Service air cleaner more often under dusty
conditions. See Engine Manual.
ENGINE OIL FILTER
Replace the engine oil filter every season or
every other oil change if the mower is used more
than 100 hours in one year.
SPARK PLUGS
Replace spark plugs at the beginning of each
mowing season or after every 100 hours of
operation, whichever occurs first. For spark plug
type and gap setting refer to your ENGINE
OWNER’S MANUAL.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
IN-LINE FUEL FILTER (See Figs. 11 and 12)
The fuel filter should be replaced once each
season. If the fuel filter becomes clogged,
obstructing fuel flow to carburetor, replacement
is required.
•
•
•
•
First turn off the fuel valve that is located
under the fuel tank of you mower.
With the engine cool, remove the filter
and plug fuel line sections.
Place new filter in position in fuel line with
arrow pointing toward the carburetor.
Be sure there are no fuel leaks and
clamps are secure and properly
positioned.
1
CZ-14
FIGURE 11
1. ENGINE FUELFILTER
•
Immediately wipe up any spilled gasoline.
1
CZ-15
FIGURE 12
1. FUEL SHUT OFF VALVE
CLEANING
•
•
•
Clean engine, battery, seat, finish, etc. of
all foreign matter.
Keep finished surfaces and wheels free
of all gasoline, oil, etc.
Protect painted surfaces with automotive
type wax
We do not recommend using a garden hose to
clean your mower unless the electrical system,
muffler, air filter and carburetor are covered to
keep water out. Water in the engine can shorten
the engine life.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENT
WARNING
CZ-16
BEFORE PERFORMING ANY SERVICE
OR ADJUSTMENTS:
•
•
Set park brake to engaged position.
Place PTO switch in the disengaged
position (pressed down).
A
•
•
•
Turn ignition key "OFF" and remove
the key.
A
Make sure the blades and all moving
parts have completely stopped.
Disconnect spark plug wire from
spark plug and place the wire where
it cannot come in contact with the
plug.
FIGURE 13
1
MOWER
TO LEVEL DECK
Adjust the deck while the mower is on a level
surface. Make sure the tires are inflated to the
correct pressure (see “SPECIFICATIONS”
section in this manual). If tires are under or over
inflated, you can not properly adjust your deck.
2
CZ-17
NOTE: It may be easier to adjust the front lift
linkages by removing the floor pan before any
adjustments are made
FIGURE 14
1. HEX NUT
2. FRONT LIFT LINKAGE
SIDE-TO-SIDEADJUSTMENT (See Figs. 13
and 14)
•
Raise the deck into the highest cutting
position (4 1/2")
•
Measure height from the bottom edge of
the deck to the ground at both front
corners. Distance “A” at both corners
should be the same.
2
•
•
If adjustment is necessary, make
adjustment to one side the deck only
To raise one side of the deck, using a 9/16"
wrench, tighten the hex nuts on both the
front and rear lift linkages (be sure to
tighten equal amounts).
1
CZ-18
•
•
To lower one side of the deck, reverse
previous step.
Recheck measurements after
adjustment.
FIGURE 14A
1. HEX NUT
2. REAR LIFT LINKAGE
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENT
FRONT-TO-BACKADJUSTMENT(SeeFig. 15).
IMPORTANT: DECK MUST BE LEVEL SIDE-
TO-SIDE. IF THE FOLLOWING FRONT-TO-
BACKADJUSTMENT IS NECESSARY, BE
SURE TO ADJUST BOTH FRONT OR BOTH
REAR LINKAGES EQUALLY SO THE DECK
WILL STAY LEVEL.
To obtain the best cutting performance, the deck
should be adjusted so the front tip of the blades
are approximately 1/8" to 1/4" lower than the rear
tip. If the front tip is higher, this will create a poor
quality of cut.
B
B
CZ-19
WARNING
FIGURE 15
Blades are sharp. Protect your hands with
gloves and/or wrap blades with a heavy
cloth when handling.
Check adjustment on the right side of the
mower. Position any blade so that the tip is
pointing straight forward. Measure distance “B”
at the front and rear tip of the blade.
•
Before making any necessary
adjustments, check to make sure that
the deck is level side-to-side.
•
With the deck in the highest cutting
position, (4 1/2") measure the front tip of
the blade to see if the deck is higher or
lower than 4 1/2".
•
To lower the front tip of the blade, using a
9/16" wrench, loosen the hex nuts that
are on the front lift linkages (be sure to
loosen equal amounts).
•
•
When distance “B” is 1/8" to 1/4" lower at
the front than rear the adjustment is
done.
Reverse above step to raise the deck.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENT
TO REPLACE DECK BELT
DECK BELT REMOVAL (See Fig. 16 and 17)
•
•
•
Park on a level surface. Apply park
brake.
Lower the deck into the lowest cutting
position
Disengage the tension relief lever from
the lock bracket.
1
2
WARNING
Lever is spring loaded. Have a tight grip
on the lever and release slowly.
•
•
Remove screws from both the left and
right belt shields, and remove shields.
FIGURE 16
1. CLUTCH PULLEY
2. 107709 DECK BELT
Remove any dirt or grass that may have
accumulated around the cutter housings
and entire deck surface.
•
•
•
Carefully roll the belt over the top of the
cutter housing pulleys.
Remove the belt from around the electric
clutch on the engine shaft.
The belt can now be removed.
DECK BELT INSTALLATION (See Figs. 16 and 17)
NOTE: For ease in installing the deck belt, refer
to the routing decal on the front edge of the
deck.
•
Wrap the deck belt around the electric
clutch that is located on the engine shaft.
Push the rest of the belt through the
IZT(Integraded Zeroturn Transaxle)
support and up onto the deck.
•
•
Starting on the right hand side of the
deck, wrap the belt around the large right
side idler, right cutter housing pulley,
small center idler, center pulley, left side
pulley and then around the large left side
idler.
1
CZ-20
FIGURE 16A
1. TENSION RELIEF LEVER
•
•
The belt will be loose at this point.
Tightly secure the belt tension rod and
reengage it in the lock bracket.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENT
TO REPLACE IZT (Integraded Zeroturn
Transaxle) BELT (See Fig. 17)
Park the mower on a level surface. Engage the
park brake.
3
1
4
IZT BELT REMOVAL
NOTE: Be careful not to damage the fan
blades on the IZT’s as this can affect cooling or
damage the IZT’s
•
Remove the deck belt (see “TO
REPLACE DECK BELT” in this section
of the manual).
5
2
6
•
•
Create slack in the belt by removing the
spring on the pump idler arm.
The belt should now be able to be
removed from the engine pulley and IZT
pulleys.
CZ-21
FIGURE 17
1. PUMP IDLER ARM SPRING
2. PUMP IDLER
3. ELECTRIC CLUTCH
4. IZT BELT
5. DECK BELT
BELT INSTALLATION
•
•
Wrap the IZT belt around the IZT pulleys
Route the belt around the inside of the
idler pulley.
6. IZT SUPPORT
•
•
•
Now you can wrap the belt around the
engine pulley.
Reattach the spring on the pump idler
arm.
Reinstall the deck belt onto the electric
clutch belt (see “TO REPLACE DECK
BELT” in this section of the manual).
1
TO ADJUST THE SEAT (See Fig. 18)
2
•
Move the control levers into the neutral
position and rotate to the outside of the
machine.
•
•
Lift up on the back of the seat and rotate
it forward.
Loosen the three prong knobs on the
bottom of the seat and move the seat to
the desired position.
3
•
Tighten the three prong knobs and rotate
seat back to the operating position.
CZ-1
FIGURE 18
1. SEAT PAN
2. KNOBS
3. WIRE HARNESS
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENT
TO ADJUST CONTROL LEVERS
(See Fig. 19)
Sitting on the seat, in the operators position,
press both control levers forward. If both control
levers line up with each other, then no
adjustment is needed. If they do not line up,
follow instructions below.
1
2
•
Identify which control lever moves further
forward.
•
Using a 9/16" wrench, slightly loosen the
bottom hex bolt (about 1/2 turn) on the
opposite control lever.
3
•
•
Move both control levers to the front
again and apply more pressure to the
control lever that you loosened to bring
the two control levers in line with each
other.
4
CZ-2
FIGURE 19
1. CONTROL LEVER
2. CONTROL ARM
3. HEX BOLTS
Tighten hex bolts.
4. NEUTRAL SLOT
TO REMOVE WHEELS FOR
REPAIR
FRONT CASTER TIRES
•
Park mower on a level surface and apply
park brake.
•
•
Jack up the front end of the mower.
Using a 3/4" wrench and/or socket w/
drive ratchet, remove hex nut and hex
bolt from the caster fork.
•
•
Remove the tire from the fork.
Remove the spacer from the inside of
the caster rim.
•
•
Repair tire
Reassemble in the reverse order of the
previous steps.
REAR TIRES
IMPORTANT: Block front tires to prevent the
mower from rolling.
•
•
•
Park mower on a level surface and apply
park brake.
Jack up the rear end of the mower on the
side of the damaged tire.
Remove 4 lug nuts to allow wheel
removal.
•
•
Repair tire.
Reassemble in reverse order of previous
steps.
NOTE: To seal tire punctures and prevent flat
tires due to slow leaks, tire sealant may be
purchased from your local parts dealer. Tire
sealer also prevents tire dry rot and corrosion.
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENT
TO START AN ENGINE WITH A
WEAK BATTERY
WARNING
Lead-acid batteries generate explosive
gases. Keep sparks, flame and smoking
materials away from batteries. Always wear
eye protection when around batteries.
If your battery is too weak to start the engine, it
should be recharged. (See “BATTERY” in the
Customer Responsibilities section of this
manual).
If “jumper cables” are used for emergency
starting, follow this procedure:
IMPORTANT: YOUR MOWER IS EQUIPPED
WITHA12-VOLT NEGATIVE GROUNDED
SYSTEM. THE OTHER VEHICLE MUSTALSO
BE A12-VOLT NEGATIVE GROUNDED
SYSTEM. DO NOT USE YOUR MOWER
BATTERY TO START OTHER VEHICLES.
TO ATTACH JUMPER CABLES
•
Connect each end of the RED cable to
the POSITIVE (+) terminal on each
battery, taking care not to short against
chassis.
•
•
Connect one end of the BLACK cable to
the NEGATIVE (-) terminal of the fully
charged battery.
Connect the other end of the BLACK
cable to a good CHASSIS GROUND,
away from the fuel tank and battery.
TO REMOVE CABLES, REVERSE ORDER
•
BLACK cable first from chassis and then
from the fully charged battery.
•
RED cable last from both batteries.
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENT
REPLACING BATTERY (See Fig. 20)
WARNING
Do not short battery terminals by allowing
a wrench or any other object to contact
both terminals at the same time. Before
connecting battery, remove metal brace-
lets, wristwatch bands, rings, etc.
1
Positive terminal must be connected first
to prevent sparking from accidental
grounding.
2
CZ-22
FIGURE 20
•
•
•
Lift Seat and rotate forward.
Open terminal access doors.
Using two 1/2" wrenches disconnect
BLACK battery cable then RED battery
cable.
1. TERMINAL GUARD
2. TERMINAL ACCESS DOORS
•
•
•
Using 7/16" wrench, remove terminal
guard.
Carefully remove the battery from the
mower.
Install new battery with terminals in the
same position as the old battery.
Reinstall terminal guard
First connect RED battery cable to
positive (+) battery terminal with hex bolt
and hex nut.
•
•
•
Connect BLACK grounding cable to
negative (-) battery terminal with
remaining hex bolt and hex nut.
Tighten securely.
Close terminal access doors.
Lower seat.
•
•
•
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENT
TO ADJUST PARK BRAKE
Before making any adjustments:
4
NOTE:Make sure the brake arm is engaged into
brake sprocket on both sides. You can push the
mower to make it engage into the sprocket.
3
5
2
•
•
With the park brake off the sping should
measure 2 3/4” both sides.
1/2”
With the brake on the gap between the
connecting link and the secondary
linkage should be 1/2” on each side.
If not loosen the nut against the yoke and
turn the secondary linkage using the
double nuts until the 1/2” gap is achieved
on both sides. See Figure 21.
M
•
1
parkbrake
FIGURE 21
1. CONNECTING LINK
2. SECONDARY LINKAGE
3. DOUBLE NUTS
4. NUT
5. YOKE
TRACKING ADJUSTMENT
If the mower is not tracking straight, check the
air pressure in both rear tires. Recommended air
pressure is 15 psi. If the unit will not track
straight, follow the steps below. Tracking must
be checked on a flat and level concrete or
blacktop surface.
•
Mower is tracking to the right. Increase
the air pressure 2-3 psi in the right rear tire
or decrease the air pressure 2/3 psi in the
left rear tire.
•
Mower is tracking to the left. Increase
the air pressure 2-3 psi in the left rear tire
or decrease the air pressure 2/3 psi in the
right rear tire.
Recheck tracking and keep making adjustments
with the tire pressure until the unit tracks straight.
DO NOT exceed maximum recommended tire
pressure 24 psi.
Record the tire pressure for future reference.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
Immediately prepare your mower for storage at
the end of the season or if the mower will not be
used for 30 days or more.
WARNING
Never store the mower with gasoline in
the tank inside a building where fumes may
reach an open flame or spark. Allow the
engine to cool before storing in any en-
closure.
MOWER
When mower is to be stored for a period of time,
clean it thoroughly, remove all dirt, grease,
leaves, etc. Store in a clean, dry area.
•
Clean entire mower (See "CLEANING" in
the Customer Responsibilities section of
this manual).
•
Inspect and replace belts, if necessary
(See belt replacement instructions in the
Service and Adjustments section of this
manual).
•
•
Lubricate as shown in the Customer
Responsibilities section of this manual.
Be sure that all nuts, bolts and screws
are securely fastened. Inspect moving
parts for damage, breakage and wear.
Replace if necessary.
•
Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
BATTERY
•
•
Fully charge the battery for storage.
After a period of time in storage, battery
may require recharging.
•
To help prevent corrosion and power
leakage during long periods of storage,
battery cables should be disconnected
and battery cleaned thoroughly (see "TO
CLEAN BATTERYAND TERMINALS" in
the Customer Responsibilities section of
this manual).
•
•
After cleaning, leave cables
disconnected and place cables where
they cannot come in contact with battery
terminals.
If battery is removed from mower for
storage, do not store battery directly on
concrete or damp surfaces.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
ENGINE
FUEL SYSTEM
IT IS IMPORTANT TO PREVENT GUM DEPOS-
ITS FROM FORMING IN ESSENTIAL FUEL
SYSTEM PARTS SUCH AS CARBURETOR,
FUEL FILTER, FUEL HOSE, OR TANK DURING
STORAGE. ALSO, EXPERIENCE INDICATES
THAT ALCOHOL BLENDED FUELS (CALLED
GASOHOL OR USING ETHANOL OR METHA-
NOL) CANATTRACT MOISTURE WHICH
LEADS TO SEPARATION AND FORMATION OF
ACIDS DURING STORAGE. ACIDIC GAS CAN
DAMAGE THE FUELSYSTEM OFAN ENGINE
WHILE IN STORAGE.
•
•
Drain the fuel tank.
Start the engine and let it run until the fuel
lines and carburetor are empty.
Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
•
•
Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alterna-
tive in minimizing the formation of fuel gum
deposits during storage. Add stabilizer to gaso-
line in fuel tank or storage container. Always
follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding
stabilizer to allow the stabilizer to reach the
carburetor. Do not drain the gas tank and carbu-
retor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace with
clean engine oil. (See "ENGINE" in the Customer
Responsibilities section of this manual).
46
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
CYLINDER(S)
•
•
Remove spark plug(s).
Pour one ounce of oil through spark plug
hole(s) into cylinder(s).
•
•
Install plugs.
Turn ignition key to "START" position for
a few seconds to distribute oil.
Replace with new spark plug(s).
•
OTHER
•
•
Do not store gasoline from one season
to another.
Replace your gasoline can if your can
starts to rust. Rust and/or dirt in your
gasoline will cause problems.
If possible, store your mower indoors
and cover it to give protection from dust
and dirt.
Cover your mower with a suitable
protective cover that does not retain
moisture. Do not use plastic. Plastic
cannot breathe which allows
condensation to form and will cause your
mower to rust.
•
•
IMPORTANT: NEVER COVER MOWER WHILE
ENGINEAND EXHAUSTAREASARE STILL
WARM.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING POINTS
PROBLEM
CAUSE
CORRECTION
Will not start
1. Out of fuel.
1. Fill fuel tank.
2. Engine not "CHOKED" properly.
3. Engine flooded.
4. Bad spark plug.
5. Dirty air filter.
2. See "TO START ENGINE" in Operation section.
3. Wait several minutes before attempting to start.
4. Replace spark plug.
5. Clean/replace air filter.
6. Dirty fuel filter.
6. Replace fuel filter.
7. Water in fuel.
7. Drain fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
8. Loose or damaged wiring.
9. Carburetor out of adjustment.
10. Engine valves out of adjustment.
11. Extreme cold conditions.
8. Check all wiring.
9. See Engine Manual.
10. Contact an authorized service center/department.
11. See "To start engine" in operation section.
Hard to start
1. Dirty air filter.
1. Clean/replace air filter.
2. Bad spark plug.
2. Replace spark plug.
3. Weak or dead battery.
4. Dirty fuel filter.
3. Recharge or replace battery.
4. Replace fuel filter.
5. Stale or dirty fuel.
5. Drain fuel tank and refill with fresh gasoline.
6. Check all wiring.
7. See Engine Manual.
6. Loose or damaged wiring.
7. Carburetor out of adjustment.
8. Engine valves out of adjustment.
8. Contact an authorized service center/department.
1. Depress brake pedal.
Engine will not
turn over
1. Brake pedal not depressed.
2. Attachment clutch is engaged.
3. Weak or dead battery.
2. Disengage attachment clutch.
3. Recharge or replace battery.
4. Replace fuse.
5. Clean battery terminals.
6. Check all wiring.
7. Check/replace ignition switch.
8. Check/replace solenoid or starter.
9. Contact an authorized service center/department.
4. Blown fuse.
5. Corroded battery terminals.
6. Loose or damaged wiring.
7. Faulty ignition switch.
8. Faulty solenoid or starter.
9. Faulty operator presence switch(es).
Engine clicks but
will not start
1. Weak or dead battery.
1. Recharge or replace battery.
2. Clean battery terminals.
3. Check all wiring.
2. Corroded battery terminals.
3. Loose or damaged wiring.
4. Faulty solenoid or starter.
4. Check/replace solenoid or starter.
Loss of power
1. Cutting too much grass/too fast.
2. Throttle in "CHOKE" position.
3. Buildup of grass, leaves and trash under deck.
4. Dirty air filter.
1. Set in "Higher Cut" position/reduce speed.
2. Adjust throttle control.
3. Clean underside of mower housing.
4. Clean/replace air filter.
5. Low oil level/dirty oil.
6. Faulty spark plug.
7. Dirty fuel filter.
5. Check oil level/change oil.
6. Clean and re-gap or change spark plug.
7. Replace fuel filter.
8. Stale or dirty fuel.
9. Water in fuel.
8. Drain fuel tank and refill with fresh gasoline.
9. Drain fuel tank and carburetor, refill tank with
fresh gasoline and replace fuel filter.
10. Connect and tighten spark plug wire.
11. Clean engine air screen/fins.
12. Clean/replace muffler.
10. Spark plug wire loose.
11. Dirty engine air screen/fins.
12. Dirty/clogged muffler.
13. Loose or damaged wiring.
14. Carburetor out of adjustment.
15. Engine valves out of adjustment.
13. Check all wiring.
14. See Engine Manual.
15. Contact an authorized service center/department.
Excessive vibration 1. Worn, bent or loose blade.
2. Bent blade mandrel.
1. Replace blade. Tighten blade bolt.
2. Replace blade mandrel.
3. Loose/damaged part(s).
3. Tighten loose part(s). Replace damaged parts.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING POINTS
CAUSE
PROBLEM
CORRECTION
Engine continues to 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not
run when operator
leaves seat with
attachment
corrected, contact an authorized service center/
department.
Poor cut - uneven
1. Worn, bent or loose blade.
2. Mower deck not level.
1. Replace blade. Tighten blade bolt.
2. Level mower deck.
3. Buildup of grass, leaves, and trash under mower. 3. Clean underside of mower housing.
4. Bent cutter housing.
4. Replace cutter housing.
5. Clogged mower deck vent holes from buildup of
grass, leaves, and trash around cutter housing.
5. Clean around cutter housing to open vent holes.
1. Obstruction in clutch mechanism.
2. Worn/damaged mower drive belt.
3. Frozen idler pulley.
1. Remove obstruction.
2. Replace mower drive belt.
3. Replace idler pulley.
Mower blades will
not rotate
4. Frozen cutter housing.
4. Replace cutter housing.
1. Engine speed too slow.
2. Travel speed too fast.
3. Wet grass
4. Mower deck not level.
1. Place throttle control in "FAST" position.
2. Shift to slower speed.
3. Allow grass to dry before mowing.
4. Level mower deck.
Poor grass
discharge
5. Low/uneven tire air pressure.
6. Worn, bent or loose blade.
7. Buildup of grass, leaves and trash under mower.
8. Mower drive belt worn.
5. Check tires for proper air pressure.
6. Replace/sharpen blade. Tighten blade bolt.
7. Clean underside of mower housing.
8. Replace mower drive belt.
9. Blades improperly installed.
10. Improper blades used.
11. Clogged mower deck vent holes from buildup of
grass, leaves and trash around cutter housing.
9. Reinstall blades sharp edge down.
10. Replace with blades listed in this manual.
11. Clean around cutter housing to open bent holes.
1. Bad battery cell(s).
1. Replace battery.
2. Check/clean all connections.
3. Replace regulator.
Battery will
not charge
2. Poor cable connections.
3. Faulty regulator (if so equipped).
4. Faulty alternator.
4. Replace alternator.
1. IZT bypass linkages in bypass position.
2. IZT belt worn, damaged, or broken.
1. Place IZT bypass linkages in drive in "engaged"
position.
2. Replace IZT belt.
Loss of drive
1. Engine throttle control not set at "SLOW"
position for 30 seconds before stopping
engine.
1. Move throttle control to "SLOW" position and
allow to idle for 30 seconds before stopping
engine.
Engine "backfires"
when turning
engine "OFF"
49
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING SCHEMATIC
50
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|