Collection System
Operators Manual
111750 / HCS1372
Models:
Parts Manual
Please read these instructions carefully and make
sure you understand them before using the machine.
MANUAL NO. 539111758 REV 01 (03/31/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
Operators Guide
Features and Controls.............................................................. 4
General Information ................................................................. 5
Safety Procedures.................................................................... 5
Unpacking Instructions ............................................................. 7
Assembly Instructions .............................................................. 7
Collection System .............................................................. 7
Blower/Drive Kit ............................................................... 11
Operating the Collection System........................................ 12
Maintenance and Service Instructions
Transport ................................................................................ 13
Cleaning and Washing ........................................................... 13
Storage ................................................................................... 13
Preventative Maintenance Schedule...................................... 13
Caring for Vacuum Hoses ...................................................... 14
Cleaning Poly Mesh ............................................................... 14
Caring for Bags ...................................................................... 14
Troubleshooting Guide ........................................................... 15
Replacement Parts
Hood Assembly ...................................................................... 18
Hitch Assembly....................................................................... 19
Blower Assembly .................................................................... 20
Weight Kit ............................................................................... 22
Mounting Kit ........................................................................... 23
Bag Assembly ........................................................................ 24
Drive Kit.................................................................................. 25
Parts Description .................................................................... 26
WARNING: Engine exhaust, some of its constituents, and certain vehicle components con-
tain or emit chemicals known to the State of California to cause cancer and birth defects or
other reproductive harm.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES & CONTROLS
HOOD
INLET
LATCH
SUPPORT LINKAGE
SUPPORT BRACKET
HITCH
HITCH BRACKET
REAR GUARD
BAG
WEIGHT BAR
DRIVE KIT
HOSE
CAST WEIGHT
BLOWER ASSEMBLY
NOTE: Your Front Weight Bar may look different from those shown in this diagram.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
Safety Procedures
General Information
This manual will assist you in the safe operation
and proper maintenance of your Husqvarna
equipment. Read it thoroughly before attempting
to operate the machine. Call your dealer or
Husqvarna if additional information is required.
1 - Training:
• Read the Operator’s manual. If the operator(s)
or mechanic(s) can not read English it is the
owner’s responsibility to explain this material to
them.
• Become familiar with the safe operation of the
equipment, operator’s controls, and safety
signs.
The following safety symbols are used throughout
the manual to alert you to information about unsafe
actions or situations:
• All operators and mechanics should be trained.
The owner is responsible for training the users.
• Never let children or untrained people operate
or service the equipment. Local regulations may
restrict the age of the operator.
• The owner/user can prevent and is responsible
for accidents or injuries occurring to themselves,
other people, and/or property.
DANGER indicates immediate hazards that
may result in severe injury or death.
WARNING indicates unsafe actions or
situations that may cause severe injury,
death, and/or major equipment or property
damage.
2 - Preparation:
CAUTION indicates unsafe actions or
situations that may cause injury and/or
minor equipment or property damage.
• Wear appropriate clothing including hard hat,
safety glasses and ear protection. Long hair,
loose clothing or jewelry may get tangled in
moving parts.
This equipment should not be modified without the
manufacturer’s prior written authorization. Doing
so may not only affect the equipments’
performance and durability, but also create safety
hazards for the operator and the surroundings.
Warranty will be void if changes are made to the
equipment without the manufacturer’s prior written
authorization.
• Inspect the area where the equipment is to be
used and remove all objects such as rocks, toys
and wire which can be thrown by the machine.
• Use extra care when handling gasoline and
other fuels. They are flammable and vapors
are explosive. Use only an approved container.
Never remove gas cap or add fuel with engine
running. Allow engine to cool before refueling.
Do not smoke while fueling or operating
equipment. Never refuel or drain the machine
indoors.
• Check that operator’s controls, safety switches,
hoses, and shields are securely attached and
functioning properly. Do not operate unless
they are functioning properly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
3 - Operation
• Use care when loading or unloading the machine
into a trailer or truck.
• Use care when approaching blind corners,
shrubs, trees, or other objects that may obscure
vision.
• Never run an engine in an enclosed area.
• Only operate in good light, keeping away from
holes and hidden hazards.
• Slow down and use extra care on hillsides.
Make turns gradually and at slow speed. Do
not operate across the sides of slopes. Operate
up and down slopes only. Do not operate on
steep slopes.
• Turf conditions can affect the machine’s stability.
Do not operate on wet grass where traction may
be reduced.
• Do not change the engine governor setting or
overspeed the engine.
• Stop equipment and inspect vacuum impeller
and hoses after striking objects or if an abnormal
vibration occurs. Make necessary repairs before
resuming operations.
• Look behind and down before backing up to
ensure a clear path.
• Slow down and use caution when making turns
and crossing roads and sidewalks. Stop vacuum
and mower blades if not mowing.
• Do not operate machine under the influence of
alcohol or drugs.
4 - Maintenance and Storage:
• Stop engine and disconnect spark plug wire.
Wait for all movement to stop before adjusting,
cleaning, or repairing.
• Clean grass and debris from muffler and engine
to help prevent fires. Clean up oil or fuel
spillage.
• Let engine cool before storing and do not store
near sparks or open flame.
• Shut off fuel while storing. Do not store fuel
near flames or drain indoors.
• Never allow untrained personnel to service
machine.
• Keep hands and feet away from moving parts.
If possible, do not make adjustments with the
engine running.
• Keep all parts in good working condition and all
hardware tightened. Replace all worn or
damaged decals.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Unpacking Instructions
1. Cut plastic tie securing the hitch to the crate top.
2. Remove the top of the crate.
3. Remove the plastic bag.
4. Remove the hose.
5. Remove the sides and ends of the crate.
6. Remove the mounting kit and drive kit boxs from the corner of the crate.
7. Cut the two plastic ties that secure the hitch assembly to the pallet. Remove the hitch assembly.
8. Cut the two plastic ties that secure the back of the hood, and the two that secure the front of the
hood. Remove the hood assembly.
9. Cut and two plastic ties that secure the weight bar to the pallet. Remove the weight bar.
10. Cut the two plastic ties that secure the blower assembly to the pallet. Remove the blower assembly.
11. Remove the 1 x 4 that secures the cast weights to the pallet. Remove the weights.
1
Assembly Instructions
Collection System
Tools Required:
Ratchet
9/16" Socket
5/8" Socket
(2) 3/4" Wrench
3/4" Socket
Torque Wrench
1/2" Wrench
1/2" Socket
9/16" Wrench
Flat Screw Driver
2
FIGURE 1
1. SUPPORT BRACKET
2. HITCH BRACKET
1. Open the mounting kit box and remove all of
the components.
2. Place the support bracket on the frame and
secure with (2) 990563, 3/8 x 1 bolts and (2)
976979, 3/8 nyloc nuts. Figure 1.
3. Place the hitch brackets on the frame and
secure with (3) 990622, 1/2 x 1 1/4 bolts and
(3) 101331, 1/2 nyloc nuts. Figure 1.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
1
2
4.
Remove the (10) 5/16 carriage bolts that
secure the standard rear guard to the straps
and skid plates. Remove the standard rear
guard. Replace with the collection rear
guard, and secure with the carriage bolts that
were just removed. Figure 2.
FIGURE 2
1. REAR GUARD
2. STRAP
2
5.
Place the hitch assembly on the ground
behind the mower. Place the (2) hitch pins
thru the hitch and the hitch brackets. Secure
the hitch pins with the (2) hairpins that are
secured with the (2) lanyards. Figure 3.
1
3
1
6.
Move to the rear of the hitch assembly and
pick it up towards the rear guard. The latch
will hook over the top of the rear guard.
Figure 3.
4
2
3
FIGURE 3
1. HITCH ASSEMBLY
2. LANYARD
3. HITCH PIN
4. LATCH
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
7.
Place the hood assembly on to the hitch
8.
Open the hood and secure the (2) springs
to the bolts on the hood assembly and the
hitch assembly. Figure 4.
assembly. Place both hood hinges between
the upper hitch mounts on the hitch assembly.
Be sure that the rubber seal is on the inside
of the hood. Place the (2) friction washers
between the hood hinge and the upper hitch
mount. Place (2)990563, 3/8 x 1 bolt thru the
hinge and mount. Secure with (2) 976979,
3/8 nyloc nut. Figure 4.
1
2
3
4
6
7
8
5
FIGURE 4
5. RUBBER SEAL
6. 3/8 NYLOC NUT
7. UPPER HITCH MOUNT
8. HITCH PIN
1. HOOD ASSEMBLY
2. HOOD HINGE
3. 3/8 X 1 BOLT
4. SPRING
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
1
9.
With the hood open, secure the (3) bags in
place. The back of the bags will hook over
the mounting tabs on the hitch assembly.
Figure 5.
2
10. Close the hood, and latch the draw latch over
the draw latch keeper on the hitch assembly.
Figure 5.
3
4
5
FIGURE 5
1. HOOD ASSEMBLY
2. DRAW LATCH
3. MOUNT TABS
4. DRAW LATCH KEEPER
5. BAG
11. Install the (2) linkage assemblies to the (2)
support brackets on hitch assembly and the
(2) support brackets on the frame. The
shorter linkage connects to the support
bracket on the hitch assembly. Figure 6.
2
3
NOTE: The linkage assemblies may need to be
adjusted. Using (2) 3/4" wrenches, loosen the 1/2"
jam nut on the longer linkage. Turn the turnbuckle
in the appropriate direction to shorten the linkage
assembly. Turn until the slop is taken out of the
linkages. Tighten the jam nut against the
turnbuckle.
4
5
1
12. Secure the front of the linkage assemblies
using the hairpin secured by the lanyard.
Secure the rear of the linkages using the (2)
990654, cotter pins provided. Figure 6.
13. Place the hose on the inlet and secure with
the hose clamp.
6
FIGURE 6
1. SUPPORT BRACKET
2. TURNBUCKLE
3. LINKAGE ASSEMBLY
4. LANYARD
5. SUPPORT BRACKET
6. HITCH BRACKET
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Blower/Drive Kit
1.
2.
3.
4.
5.
Open the drive kit box and remove all of
the components.
Place the deck in the lowest cutting
height.
Remove the right side belt shield from the
deck.
Remove the deck belt from the right side
pulley.
1
Remove the deck pulley.
2
3
Note: When the deck pulley is removed, the
spindle can fall out of the cutter housing
assembly. Be sure to secure the bottom
of the spindle so that this does not
happen.
6.
Place the double pulley on the cutter
housing assembly.
7.
8.
9.
Place the heavy washer, and 7/16 lock
washer on the 108951, 7/16 x 2 1/2 bolt and
install in the spindle. Torque to 45 ft/lbs.
4
Remove the discharge chute from the deck.
Verify that the belt is on the pulley in the
blower.
5
Place the deck plate pin in the tube on the
back edge of the deck. Rotate the blower
around and into place. Figure 1.
FIGURE 1
1. DECK PLATE PIN
2. TUBE
3. ROTATE
4. IDLER ARM
5. IDLER KEEPER
10. Install the pin thru the tabs on both the deck
and the blower. Figure 1.
11. Latch the idler arm in the idler keeper.
Figure 1.
12. Install the belt on the deck pulley and
release the idler arm from the keeper.
13. Install the new belt shield.
14. Place the hose on the blower housing and
secure with the over center hose clamp.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Operating the Collection System
1. NEVER USE THE COLLECTION SYSTEM
WITHOUT THE BLOWER ASSEMBLY
AND HOSES SECURELY ATTACHED.
2. Make sure hoses are connected at both
ends. Inspect hoses prior to each use.
3. Do not use the unit on slopes greater than
10 degrees.
4. The mower must be running in order to
vacuum debris through the mower deck.
5. In heavy grass it may be necessary to mow
and collect at a slower ground speed.
6. Never attempt to unclog the collection sys-
tem until the mower’s engine engine has
been shut off and all moving parts have come
to a complete stop.
7. Do not stand behind the vent at the rear of
the collection system due to the potential for
small pieces of blowing debris to escape
through the vent.
8. Wear eye and ear protection.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND MAINTENANCE
Transport
For best results, clean poly mesh inside hood regu-
larly. Instructions for doing this can be found in
the Service section of this manual.
WARNING
The collection system bags must be com-
pletely empty or removed while driving for-
ward onto a trailer. If the mower must be
loaded onto a trailer while there is still de-
bris in the container, the mower must be
backed up onto the trailer to avoid tipping.
Storage
Cleaning and Washing
1. Clean machine.
Regular cleaning, washing, and lubricating will
prolong the service of the machine.
2. Cover all scratches with touch-up paint.
3. Covered or indoor storage is recommended.
NOTE: Use care with power washers to avoid
damage to decals. Limit direct spray on these
items.
DO NOT EXCEED 1000 PSI WATER PRESSURE
FOR CLEANING.
Preventative Maintenance Schedule
Item
Before
Each Use
Every
5 Hours
Every
25 Hours
Every
50 Hours
Inspect/Clean Poly Mesh
Check/Tighten Nuts & Bolts
Check/Tighten Hoses
Turn Hose End to End
Rotate Hose
X
X
X
X
X
X
X
Clean Machine
Inspect Bags
X
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND MAINTENANCE
Caring For Hoses
Caring For Bags
1. Inspect hoses before each use. If hoses have
excessive wear, tears, or punctures, replace
immediately.
Inspect the bags before each use. If bags have
excessive wear, tears or punctures, replace im-
mediately.
2. To prolong the life of the hose, periodically ro-
tate hose and turn hose end to end. Refer to
Preventative Maintenance Schedule in this
manual.
Cleaning Instructions
NOTE: Under normal usage the bag material is
subject to deterioration and wear.
3. Avoid twists and sharp turns in the hoses, as
they will increase wear on the hoses.
4. Avoid dragging the lower hose along the sides
of buildings or other hard surfaces.
Cleaning Poly Mesh
The poly mesh on the collection system is located
inside the container hood. For best results, clean
poly mesh regularly.
Cleaning Instructions
1. Shut off engine.
2. Release the two (2) rubber latches under the
rear of the hood. Open hood and brush debris
off of both sides.
3. Close hood and re-latch.
DO NOT USE THE COLLECTION SYSTEM
WITHOUT POLY MESH SECURELY IN PLACE.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND MAINTENANCE
Troubleshooting Guide
DANGER
Before servicing unit, wait for all moving parts
to come to a complete stop. Turn engine off
and remove the spark plug wire.
PROBLEM
POSSIBLE CAUSE
CORRECTION
Loss of Vacuum.
1. Blower, hose or hood inlet clogged.
2. Bags full.
1. Remove hose and clean inlet.
2. Inspect and empty.
3. Fan blades bent or broken.
4. Poly mesh plugged.
3. Replace/repair impeller.
4. Clean poly mesh.
Unusual vibration
or noise.
1. Solid object jammed in unit.
1. Check and remove any
obstruction.
2. Tighten or replace bolts.
3. Replace/repair impleller.
2. Loose or missing bolts on unit.
3. Bent or damaged fan.
Unit difficult to close.
1. Obstructions keeping door from
completely closing.
2. Hood hinge bolts too tight.
1. Clear obstructions.
2. Loosen bolts.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SPINDLE DRIVE ASSEMBLY
NOTE: Your Front Weight Bar may look different from those shown in this diagram.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ILLUSTRATIONS
17
Download from Www.Somanuals.com. All Manuals Search And Download.
HOOD ASSEMBLY
539 99 07-30 (x 2)
539 99 06-13 (x 2)
539 99 06-45 (x 6)
539 11 11-81 (x 2)
539 11 00-33 (x 8)
539 11 11-72
539 97 69-79 (x 8)
539 11 11-77 (x 2)
539 20 06-84 (x 30)
539 99 05-98 (x 16)
539 97 69-78 (x 8)
539 20 06-84 (x 30)
539 20 06-84 (x 30)
539 99 05-98 (x 16)
539 99 10-03 (x 8)
539 11 11-82
539 11 13-39
539 11 17-55
539 20 06-84 (x 30)
539 11 12-60
539 11 11-75 (x 2)
539 11 11-83
539 10 27-44 (x 11)
539 10 54-08 (x 12)
539 11 11-86 (x 6)
539 11 11-86 (x 6)
539 20 04-78 (x 2)
539 97 69-77 (x 6)
539 11 11-74
539 10 27-44 (x 11)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
HITCH ASSEMBLY
539 11 11-62 (x 2)
539 99 05-63 (x 20)
539 97 69-79 (x 22)
539 99 05-63 (x 20)
539 11 11-58 (x 2)
539 11 11-87 (x 4)
539 99 05-80 (x 3)
539 99 02-54 (x 4)
539 99 06-25 (x 4)
539 11 11-67
539 11 11-71
539 97 69-79 (x 22)
539 97 69-78 (x 3)
539 97 69-79 (x 22)
539 10 13-31 (x 2)
539 11 11-57
539 11 12-67 (x 2)
539 99 05-63 (x 20)
539 97 69-79 (x 22)
539 10 83-69 (x 2)
539 99 06-55 (x 2)
539 99 06-13 (x 2)
539 11 11-55
539 97 69-79 (x 22)
539 99 05-63 (x 20)
539 97 72-50 (x 2)
539 11 11-90
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BLOWER ASSEMBLY
539 10 25-35
539 99 07-17 (x 12)
LOCKING COLLAR
539 99 01-96 (x 3)
539 10 67-86 (x 2)
THIS SIDE UP
539 10 26-91 (x 5)
539 11 13-31
539 10 67-41
539 10 57-43
539 99 02-08
539 10 81-20 (x 12)
539 10 57-85
539 99 07-17 (x 12)
539 99 00-74 (x 10)
539 88 03-16 (x 7)
539 10 04-72 (x 3)
539 11 13-32
539 10 26-91 (x 5)
539 88 03-16 (x 7)
539 10 67-86 (x 2)
539 10 26-91 (x 5)
539 11 12-27
THIS SIDE DOWN
539 11 12-29 (x 3)
539 99 07-17 (x 12)
539 99 06-92 (x 2)
539 11 17-47
539 11 12-65
539 11 12-25
539 99 07-17 (x 12)
539 99 07-17 (x 12)
539 11 12-18
539 10 20-67
539 11 08-13
539 10 04-13
539 10 67-21
539 10 22-44 (x 3)
539 99 01-22
539 20 02-82
539 10 67-13
539 99 05-17
539 99 05-46
539 91 61-59
539 99 06-92 (x 2)
HUB DOWN
539 10 17-21
539 99 05-85
539 10 65-04
539 99 02-47
539 10 01-41
539 97 69-79 (x 4)
539 99 05-98 (x 12)
539 99 07-17 (x 12)
539 11 12-29 (x 3)
539 11 17-46
539 11 11-84
539 10 81-20 (x 12)
539 99 05-98 (x 12)
539 99 05-98 (x 12)
539 10 81-20 (x 12)
539 11 13-40
539 10 27-44 (x 6)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
BLOWER ASSEMBLY
539 10 81-20 (x 12)
539 99 05-98 (x 12)
539 10 25-63
539 11 12-70
539 11 17-52
539 11 13-28
539 10 81-20 (x 12)
539 99 05-98 (x 12)
539 99 00-74 (x 10)
539 97 69-79 (x 4)
539 99 00-74 (x 10)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
WEIGHT KIT
539 02 09-21
539 11 13-13
539 10 20-49 (x 2)
539 10 80-96 (x 2)
539 11 12-59 (x 2)
539 97 69-41 (x 4)
539000019 (x 3)
539 99 05-17 (x 4)
539 97 69-79 (x 4)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUNTING KIT
539 10 29-98 (x 2)
539 97 69-79 (x 6)
539 99 05-63 (x 6)
539 99 06-54 (x 2)
539 11 12-08 (x 2)
539 11 12-07 (x 2)
539 97 69-89 (x 2)
539 10 25-63 (x 4)
539 09 70-76
REF.
539 11 11-91 (x 2)
539 10 87-36 (x 2)
539 11 12-10 (x 2)
539 11 11-97
539 97 69-79 (x 6)
539 11 11-92 (x 2)
539 11 12-15 (x 2)
539 10 25-63 (x 4)
539 99 05-63 (x 6)
539 11 13-22, RIGHT
539 11 11-99, LEFT, NOT SHOWN
539 11 12-06 (x 2)
539 99 06-22 (x 6)
539 11 12-12
539 10 13-31 (x 6)
539 10 99-01
23
Download from Www.Somanuals.com. All Manuals Search And Download.
BAG ASSEMBLY
539 11 00-63
539 99 07-17 (x 7)
539 99 03-16 (x 7)
539 11 11-66
539 99 07-99 (x 7)
539 99 06-92 (x 3)
539 99 07-17 (x 7)
539 11 11-68
24
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVE KIT ASSEMBLY
(539) 111749 - 72 INCH DECK
539 11 07-40 (x 2)
539 11 17-51
539 10 57-43
539 10 57-44
539 10 96-60
539 97 69-98
539 10 89-51
539 11 13-44
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS DESCRIPTION
PART NUMBER DESCRIPTION
539 02 09-21
539 09 70-76
539 10 01-41
539 10 04-13
539 10 04-72
539 10 13-31
539 10 13-31
539 10 17-21
539 10 20-49
539 10 20-67
539 10 22-44
539 10 25-35
539 10 25-63
539 10 25-63
539 10 26-91
539 10 27-44
539 10 29-98
539 10 54-08
539 10 57-43
539 10 57-44
539 10 57-85
539 10 65-04
539 10 67-13
539 10 67-21
539 10 67-41
539 10 67-86
539 10 80-96
539 10 81-20
539 10 83-69
539 10 87-36
539 10 89-51
539 10 96-60
539 10 99-01
539 11 00-33
539 11 00-63
539 11 07-40
539 11 08-13
539 11 11-55
539 11 11-57
539 11 11-58
539 11 11-62
539 11 11-67
539 11 11-71
539 11 11-72
539 11 11-74
539 11 11-75
539 11 11-77
539 11 11-81
539 11 11-82
539 11 11-83
539 11 11-84
539 11 11-86
WEIGHT BAR, FRONT
HOSE CLAMP 6”-& 7”
HCS, 7/16-20 X 1 1/2, GR5
RHSNB, 3/8-16 X 1 1/4, GR5
RHSNB, 5/16C X 1 1/4
NUT, 1/2C, NYLOC
NUT, 1/2C, NYLOC
HCS, 5/16-18 X 2 3/4, GR5
CLEVIS PIN
KEY, 1/4” SQ. X 3/4”
BUSHING, MACHINE, 18 GA
GREASE CAP
LANYARD
LANYARD
FLANGETTE
RIVET, 3/16 X 1/4
FRICTION WASHER
WASHER, #10
DECAL, NO STEP
DECAL, DANGER BELT DRIVES
DECAL, WARNING
WASHER, HEAVY
SHEAVE, 4”
IDLER
DECAL, SERVERING
BEARING
SPRING RETAINER
NUT, 1/4C, THIN NYLOC
HCS, 1/2-13 X 1 1/4
NUT, 1/2-20, HEX JAM
HCS, 7/16-20 X 2 1/2, GR5, SPEC.
DRAW LATCH
OVER CENTER BAND
WASHER, #10
HANGER, BAG
RIVET, BLIND, DOME STYLE, 5/32 DIA.
RETAINER, 1/4C, “U” TYPE
HITCH
MOUNT Z BRACE
SUPPORT, OUTER
SUPPORT ARM
SEAL, RUBBER
SEAL STRAP
HOOD
HOOD SUPPORT
SUPPORT, DRAW LATCH
HOOD HINGE
MOUNT PLATE
INLET TUBE
MESH, POLY DIAMOND
BELT GUIDE
SCREW, #10-24 X 1 1/8, MACH.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS DESCRIPTION
PART NUMBER DESCRIPTION
539 11 11-87
539 11 11-90
539 11 11-91
539 11 11-92
539 11 11-97
539 11 11-99
539 11 12-06
539 11 12-07
539 11 12-08
539 11 12-10
539 11 12-12
539 11 12-15
539 11 12-18
539 11 12-25
539 11 12-27
539 11 12-29
539 11 12-59
539 11 12-60
539 11 12-65
539 11 12-67
539 11 12-70
539 11 13-13
539 11 13-22
539 11 13-28
539 11 13-31
539 11 13-32
539 11 13-39
539 11 13-40
539 11 13-44
539 11 17-46
539 11 17-47
539 11 17-51
539 11 17-52
539 11 17-55
539 20 02-82
539 20 04-78
539 20 06-84
539 88 03-16
539 91 61-59
539 97 69-41
539 97 69-77
539 97 69-78
539 97 69-79
539 97 69-89
539 97 69-98
539 97 72-50
539 99 00-74
539 99 01-22
539 99 01-96
539 99 02-08
NUT, 1/2-13, WHIZLOCK
LATCH
SPRING
HAIRPIN
REAR GUARD
HITCH BRACKET, LEFT (NOT SHOWN)
HITCH PIN
TURNBUCKLE, 1/2”
SUPPORT LINKAGE, LH
SUPPORT LINKAGE
DECAL, HOT SURFACE
SUPPORT BRACKET
IDLER ARM
FLOOR WELDMENT
BEARING PLATE
SCREW, 1/4-20 X 5/8, BTN, SKT HD
WEIGHT KEEPER
DECAL, VENTILATION
KEEPER, IDLER
BRACKET, SUPPORT
PIN
HOLD DOWN, WEIGHT BAR
HITCH BRACKET, RIGHT, W/DECAL
BLOWER DECK PLATE
FAN COVER
FAN WELDMENT
HOOD SUPPORT, REAR
BLOWER SUPPORT
PULLEY, STACKED DOUBLE
BLOWER HOUSING
PULLEY SHIELD
BELT SHIELD W/DECALS & LATCH
BELT
HOSE
NUT, 3/8-16, JAM NYLOC
DRAW LATCH, FLEXIBLE T-HANDLE
RIVET, 1/4 STAVEX
RHSNB, 5/16 X 3/4
SPRING
HCS, 3/8-16 X 1 1/4, GR5
NUT, #10-24, NYLOC
NUT, 1/4C, NYLOC
NUT, 3/8C, NYLOC
HAIRPIN #4
ZERK
SPRING
RHSNB, 1/4-20 X 3/4, GR2
WASHER, 3/8, SAE
NUT, 5/16C
RHSNB, 5/16-18 X 1, GR5
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS DESCRIPTION
PART NUMBER DESCRIPTION
539 99 02-47
539 99 02-54
539 99 03-16
539 99 05-17
539 99 05-46
539 99 05-63
539 99 05-80
539 99 05-85
539 99 05-98
539 99 06-13
539 99 06-22
539 99 06-25
539 99 06-45
539 99 06-54
539 99 06-55
539 99 06-92
539 99 07-17
539 99 07-30
539 99 10-03
ER92531
LOCKWASHER, 7/16
WASHER, 1/2
RHSNB 5/16-18 X 5/8, GR5
WASHER, 3/8
NUT, 3/8, CENTERLOCK
HCS, 3/8-16 x 1, GR5
HCS, 1/4-20 X 3/4
NUT, 5/16C
WASHER, 1/4
NUT, 3/8C
HFS, 1/2-13 X 1 1/2
NUT, 1/2, JAM
RHSNB, 3/8-16 X 1
COTTER PIN, 5/32 X 1 1/4
HCS, 3/8-16 X 1 1/2
WASHER, 5/16
NUT, 5/16C, NYLOC
HCS, 3/8-16 X 1 3/4
HCS, 1/4-20 X 1 3/4
CAST COUNTERWEIGHT
28
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|