HSK141HD
®
319-318
2.25 MILLION CANDLE POWER
CORDED, CORDLESS, RECHARGEABLE SPOTLIGHT
WITH BUILT-IN STAND AND AREA UTILITY LIGHT
OWNER’S MANUAL
& WARRANTY INFORMATION
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USING, READ AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS,
PLUS YOUR VEHICLE’S BATTERY MANUFACTURER GUIDELINES. FAILURE TO DO SO COULD
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
4140 SW 28TH WAY, FT. LAUDERDALE, FL 33312
TOLL FREE: 800-916-7004
Download from Www.Somanuals.com. All Manuals Search And Download.
• Built-in hanging lanyard for hands-free convenience
• Cordless operation allows complete freedom of movement, corded for longer run time
• Pistol-grip handle fits comfortably in your hand
• Locking Trigger ON/OFF Switch delivers an instant beam, locks for continuous beam
• Unique switch-locking mechanism prevents accidental battery rundown
• May be charged from either AC or DC Power Sources (both charging adapters included)
BUILD-IN
WORKSTAND
FIGURE 1
BATTERY STATUS
PANEL
SLIDING TRIGGER
LOCK
AREA UTILITY
LIGHT SWITCH
TRIGGER SWITCH
AREA LIGHT
2. CHARGING:
FIGURE 2
CHARGING PORT
NOTE: During charging, use the handy, built-in stand (See Figure 3) to provide a steady base
for the spotlight on floor, shelf, workbench, or vehicle floor.
Charging with AC 110/120 Volt AC charger - Plug the AC charger (included) into the
charging port on the back of the HUSKY spotlight 2.25 body, and then plug into a standard AC
wall outlet. Make sure the electric rating of your AC Power Supply matches the requirements
listed on top of the AC CHARGER (110V AC). Make sure the Trigger Switch is in the OFF
position. For initial charge, allow 20 hours for completion of a full charging cycle. For subse-
quent charges, allow approximately 8-10 hours. Charge until the green Battery Status Panel
LED is lit.
NOTE: Charging from a 110/120 Volt AC power source is the most efficient method and is
especially recommended for first-time charging.
Charging/Powering with 12 VOLT DC Charger - Plug the DC fused Recharge/Power
Adapter (included) into the barrel receptacle on the back of the spotlight body, and then insert
the cigarette lighter plug into the cigarette lighter socket of your vehicle or other 12 VDC power
source. Make sure the Locking Trigger Switch is in the OFF position. Allow approximately 3–5
hours charging time if the engine is running. You may use the spotlight while its internal battery
is recharging. When the spotlight is OFF charge until the green battery status panel LED is lit.
NOTE: Be sure to use only the adapter cords supplied by the manufacturer for recharging -
The use of unauthorized adapter cords may damage the unit and will void the warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
3. OPERATION:
The Spotlight can be operated with or without the battery installed. Operation from external
12 volt DC source with at least 10 amps capacity will allow lamp operation and internal
battery charge.
SPOTLIGHT – Using the locking trigger switch:
• The trigger switch is located on the front of the pistol-grip handle of the spotlight
(See Figure 1)
• To turn the Spotlight 2.25 ON, squeeze the trigger switch
• To turn the Spotlight 2.25 OFF, release the trigger switch
• To lock the trigger switch into the ON position for continuous operation, squeeze the trigger
switch and firmly slide the trigger locking button (see Figure 1); the spotlight will stay on until
the lock is released
AREA UTILITY LIGHT
• Will provide 14 hours of continuous utility lighting - THE AREA UTILITY LIGHT is ideal for
roadside repairs, as a flashlight, for work areas, for use as a campsite area light, for power
outages, etc
• The ON/OFF button for the area light is located near the bottom of the handle, on the left
side (see Figure 1 & 3)
• To turn the area light ON, press the button
• To turn the area light OFF, press the button
NOTE The area light switch also turns on the Battery Status Panel LEDs. Recharge when just the
red LED is lit.
4. HANDS-FREE OPERATION:
USING THE BUILT-IN HANGING LANYARD:
The lanyard may be used to hang the spotlight from a branch, hook or other convenient object.
Adjust the slide on the cords to keep the lanyard secure around the supporting object.
USING THE BUILT-IN STAND:
• Lift and rotate the stand to desired angle
• Turn the spotlight upside-down, and rest it on the stand (see Figure 3)
• The spotlight and/or area utility light may now be used hands-free
• For hand-held operation, simply fold the stand into the storage postion
FIGURE 3
AREA UTILITY
LIGHT SWITCH
UTILITY WORK
STAND
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5. BULB REPLACEMENT:
For bulb replacement you will need a small Phillips screwdriver. To replace the H3 12 Volt
100 watt Halogen Spotlight Bulb (See Figure 4A and Figure 4B):
1. Disconnect the Spotlight 2.25 from any charging/power source and lock the spotlight
trigger switch OFF
2. Remove the rubber bezel by pulling it away from the spotlight lens.
3. Remove the two Phillips-head screws that hold the retaining ring to the spotlight body.
4. Pull off the retaining ring and set it aside.
5. Carefully remove the glass lens, rubber “O” ring and reflector assembly.
6. Loosen (no need to fully remove) the phillips-head screw in the neck of the reflector
assembly - this will release the bulb unit.
7. Disconnect the bulb’s center conductor wire from it’s connecting wire (See figure 4B for bulb
removal details).
8. Unsnap the hairpin retaining wires from the reflector’s flange.
9. Using the screwdriver, loosen the retaining screw to remove the bulb from the reflector
(no need to completely remove this screw).
10. Gently pull out the bulb unit and replace with a new H3 12V 100 watt Halogen Bulb
from HUSKY (or minimum H3 12V 55W), available from an electrical supply house or
from HUSKY’s Technical Support Department, call (800) 916-7004.
11. Insert the replacement bulb into the reflector’s flange.
12. Put back and secure the hairpin retaining wires.
13. Connect the bulb power wire to the red power wire.
14. Reverse the above procedure to re-assemble the spotlight.
FIGURE 4A
RUBBER
O RING
GLASS
LENS
RETAINING
RING
RUBBER
BEZEL
REFLECTOR
PHILLIPS
SCREWS
BATTERY
STATUS
PANEL
NOTE: It is recommended that the unit be returned to Vector for replacement of the spotlight
bulb. Contact HUSKY’s Technical Support Department at (800) 916-7004.
NOTE: When handling a new halogen bulb, do not touch the glass portion of the bulb.
Natural oils from your hands can cause the bulb to fail. If necessary, clean the bulb with alcohol
or a liquid window cleaner.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
HAIRPIN RETAINING
WIRES
FIGURE 4B
BULB
Open
REPLACEMENT
Closed
REPLACING THE AREA LIGHT BULB:
1. This 12V bulb is designed to last for the lifetime of the product.
2. In the event of failure, you may return the spotlight to HUSKY for bulb replacement.
Contact HUSKY’s Technical Support Department at (800) 916-7004.
6. BATTERY:
• The life expectancy of the 12 Volt 3.0 Amp-hour, sealed lead-acid battery is approximately
500 charging cycles. A replacement battery may be purchased through the HUSKY
Technical Support Department by calling (800) 916-7004
• A fully-charged battery will provide approximately 20 minutes of continuous light from the
spotlight, or up to14 hours of continuous light from the area utility light
• Do not allow battery to completely discharge, a dim light indicates that the battery charge is
low, and should be recharged. Charge battery as soon as possible after each use; monitor
charge status by color
REPLACING THE BATTERY PACK:
All lead acid batteries fail over time and with extreme temperature changes. Keeping the
battery charged periodically will extend battery life to the maximum. Recharge after each use
as soon as possible using AC/DC recharge adapter as DC recharge methods may not fully
recharge the battery to its full capacity. If the battery does not operate the spotlight for more
than 10 minutes and recharge is sufficient to fully charge the battery, then it is time to replace
the battery.
1. Disconnect the SPOTLIGHT 2.25 from the Charging/Powering Source.
2. Make sure the Trigger Switch is turned OFF and locked.
3. Follow the lamp replacement procedures to step 10.
4. Carefully disconnect the positive and negative wires from the battery terminals, noting
the position of the wires.
5. Using a small Phillips head srewdriver remove 4 battery hold down strap screws.
6. Set the battery aside and insert the new battery taking care to MATCH UP THE PROPER
POLARITY - POSITIVE (red) to positive; negative (Black) to negative.
7. Attach wires to terminals.
8. Replace the battery hold down straps and screws (Do not over-tighten - clockwise)
9. Reassemble spotlight reflector by reversing the bulb replacement procedure.
10.Test the spotlight by operating the trigger switch. Charge the new battery for 20 hours
using the AC/DC Recharge Adapter.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
FIGURE 5
POSITIVE BATTERY
TERMINAL
BATTERY
NEGATIVE
BATTERY
TERMINAL
BATTERY
HOLD DOWN
STRAPS (2)
HOLD DOWN SCREWS (4)
BATTERY DISPOSAL:
1. Non-spillable sealed lead-acid Battery - This battery is fully recyclable and should be
accepted at any location that accepts common automotive starter batteries. Examples of
places that accept these batteries are: County or municipal recycling drop-off centers,
scrap metal dealers, and retailers who sell automotive replacement lead acid starter
batteries. For more information on recycling this battery, call toll-free (877) 288-7722.
2. Before disposing of the battery, protect exposed terminals with heavy-duty tape to
prevent shorting (Shorting can result in injury or fire).
3. Do not expose battery to fire or intense heat as it may explode.
FUSE REPLACEMENT:
RECYCLE
The plug of the DC Power/Charging adapter is equipped with a 10 amp cartridge fuse. If
this fuse blows, there may be a short circuit in the power cord or lamp assembly. The fuse
will blow if the battery is connected with reverse polarity. The fuse is accessed by unscrew-
ing (counter-clockwise) the tip of the large DC plug. Check the fuse with an ohmmeter or
other continuity checker. If the fuse is open, investigate why it blew and correct the problem
before replacing the fuse. Reassemble the DC plug and power the lamp from a 8 Amp or
greater 12 volt power supply.
SPECIFICATIONS
Spotlight Bulb .................................................................................. 12 volt, H3 series
Battery .................................. Maintenance free, sealed lead acid, 12 volt, 3 Amp Hour
Weight ......................................................................................... 6 lbs 2 oz (1.5 kg)
Depth ............................................................................................. 9.0 in (22.9 cm)
Width .............................................................................................. 6.5 in (16.51 cm)
Height ............................................................................................ 11.5 in. (29.21 cm)
Download from Www.Somanuals.com. All Manuals Search And Download.
7
WARRANTY:
HUSKY 2 YEAR LIMITED WARRANTY PROGRAM
The Home Depot warrants this Husky Power Product to the original user to be free from defects in
material and workmanship for a period of two years from the date of purchase. If you believe that this
unit is defective during its original two-year warranty period, return the unit, with proper proof of
purchase to The Home Depot store or send the product to Husky Power Products at the address below.
This Husky Power Products is warranted, to the original purchaser only, to be free of defects in mate-
rials and workmanship for two years from the date of purchase without additional charge. The war-
ranty does not extend to subsequent purchasers or users. Husky Power Products will not be responsible
for any amount of damage in excess of the retail purchase price of the product under any circum-
stances. Incidental and consequential damages are specifically excluded from coverage under this
warranty.
This product is not intended for commercial or rental application, only a 90 day warranty will apply in
this instance. This warranty does not apply to accessories or damage to units from misuse or incorrect
installation. Misuse includes wiring or connecting to improper polarity power sources.
RETURN/REPAIR POLICY: If you believe that the product is defective during the it’s two year Limited
Warranty period, return the unit, with proof of purchase to the Home Depot Store. Defective products,
may also be returned postage prepaid to Husky Power Products. Any defective product, other than
accessories, that is returned to Husky Power Products within 30 days of the date of purchase will be
replaced free of charge. If such a product is returned more than 30 days but less than two years from
the purchase date, Husky Power Products will repair the unit or, at its option, replace it free of charge.
If the unit is repaired, new or reconditioned replacement parts may be used, at Husky Power Products’
option. A unit may be replaced with a new or reconditioned unit of the same or comparable design.
The repaired or replaced unit will then be warranted under the terms of the remainder of the warranty
period.
The customer is responsible for the shipping charges on all returned items. During the warranty
period, Husky Power Products will be responsible for the return shipping charges to the customer.
LIMITATIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects resulting
from normal wear and tear (including chips, scratches, abrasions, discoloration or fading due to
usage or exposure to sunlight), accidents, damage during shipping to our service facility, alterations,
unauthorized use or repair, neglect, misuse, abuse, failure to follow instructions for care and mainte-
nance, fire, flood, and Acts of God.
If your problem is not covered by this warranty, call Husky Power Products Technical Support
Department at toll-free (800) 916-7004 for general repair information and charges if applicable.
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations
on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential
damages, so the exclusions or limitations stated herein may not apply. This warranty gives the
purchaser specific legal rights; other rights, which vary from state to state, may apply.
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Husky Power Products Technical
Support by telephone, fax or mail. We suggest that you keep the original packaging in case you need
to ship the unit. When returning a product, include your name, address, phone number, dated sales
receipt (or copy), and a description of the reason for return and product serial number. After replacing
the unit, we will return it to you within four weeks.
All HUSKY products must be registered within (30) days of purchase to activate this warranty.
Mail the completed registration form, along with a copy of the original sales receipt to:
®
ATTN.: CUSTOMER SERVICE / HUSKY
4140 SW 28th Way, Ft. Lauderdale, FL 33312
TOLL FREE: (800) 916-7004
WARRANTY MUST BE WITHIN 30 DAYS OF PRODUCT PURCHASE DATE.
WARRANTY IS NON-TRANSFERABLE AND NON-REFUNDABLE.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
|