Outdoor Low
Profile Light Kit
Owner’s Guide and Installation Manual
Manual De Propietario
Form# 43545-01
20090514
©2009 Hunter Fan Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Methods of Hunter® Ceiling Fans Type A-Z
Your
® light kit can be installed in one of three
ways. e steps in this manual include instructions for
all three installation methods: Installation on fans with
removeable switch housings, fans with non-removeable
switch housings, and e Hunter Original.
Preparing the Light Kit:
1. Disconnect power by turning off the circuit breakers
both to the outlet box and to its associated wall switch
location.
Removable Switch Housing
Non-removable Switch Housing
e Hunter Original
3
43545-01 • 05/14/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
1 • Installing the Light Kit on Fans With Removable Switch Housings
1. Unscrew the three screws from the upper switch housing. Disconnect
the 9-pin plug connectors. Remove the lower switch housing.
2. Push the plug button from inside the lower switch housing to remove
the plug button and switch housing cap.
NOTE: Save the plug button and switch housing cap should you
choose to remove the light fixture in the future.
3. Ensure the gasket is in place on the light kit mounting plate. Feed the
two wires from the light kit up through the center hole in the gasket
Removable Switch Housing
and the lower switch housing.
4. Align the keyholes of the light kit and the holes in the gasket and the
screw holes of the lower switch housing.
5. Install the nut and washer onto the threaded rod from the light kit to
secure the lower switch housing.
6. Finish attaching the light kit to the lower switch housing using the
9-Pin Plug
Connector
two attachment screws removed from the lower switch housing
and the lock washers on the red tag. Partially install the screws into
the light kit and the housing. Rotate the housing counterclockwise
until the screws are locked into the narrow ends of the keyhole
slots. Securely tighten the two screws. e gasket should now be
sandwiched securely between the light kit assembly and the switch
housing assembly.
Screw
Lower Switch
Housing
WARNING: Improper installation could cause the light fixture to fall.
Plug Button
Steps 1-2
Step 5
Step 6
Switch
Housing
Wires
Washer
Threaded
Nut
Rod
Light Kit
Screw
Gasket
4
43545-01 • 05/14/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
1 • Installing the Light Kit on Fans With Removable Switch Housings (Continued)
7. Remove the wire connectors from the two wires in the switch housing
labeled “Connect Light Here” or “For Light Use.”
To connect the wires, hold the bare metal leads together and place a
wire connector over them, then twist the wire connector clockwise until
tight.
Connect the black wire with a white stripe from the switch housing to
Wires
and Wire
connectors
the black wire from the light kit. Connect the white wire from the switch
housing to the white wire from the light kit. Secure all wire connections
using wire connectors.
8. Reconnect the 9-pin plug connector.
CAUTION: Be sure no bare metal wires or wire strands are visible after
making the connections.
Step 7
9. Install screws to reattach the lower switch housing to the upper switch
housing.
10. Go to the instructions for installing the bulbs and globe.
5
43545-01 • 05/14/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
2 • Installing the Light Kit on Fans With Non-Removable Switch Housing
1. Uninstall the two attachment screws from the switch housing cover.
2. Remove the plug or screw from the center of the switch housing cover.
3. Ensure the gasket is in place on the light kit mounting plate. read the
switch housing cover onto the wires from the light kit. Align the large
ends of the keyholes in the light kit with the screw holes in the switch
housing cover. e gasket should now be sandwiched securely between
the light kit mounting plate and the switch housing cover. Install the nut
and washer onto the threaded rod from the light kit to secure the switch
housing cover.
Non-Removable Switch
Housing
4. Finish attaching the light kit to the switch housing cover using the two
attachment screws removed from the lower switch housing and the lock
washers on the red tag. Partially install the screws into the light kit and
the housing. Rotate the housing counterclockwise until the screws are
locked into the narrow ends of the keyhole slots. Securely tighten the two
screws.
5. Remove the wire connectors from the two wires in the switch housing
labeled “Connect Light Here” or “For Light Use.” One wire is white and the
other wire is black with a white stripe.
Switch
Housing
Cover
To connect the wires, hold the bare metal leads together and place a wire
connector over them, then twist the wire connector clockwise until tight.
Connect the black wire with a white stripe from the switch housing to
the black wire from the light kit. Connect the white wire from the switch
housing to the white wire from the light kit. Secure all wire connections
using wire connectors previously
Attachment
Screw
Steps 1-2
Plug
Step 3
Nut
removed.
Switch
Housing
Cover
Switch
Washer
Housing
Cover and
Gasket
Screw
Hole
Wires
and Wire
connectors
CAUTION: Be sure no bare metal
wires or wire strands are visible
after making the connections.
WARNING: Improper installation
could cause the light fixture to fall.
Step 5
6
43545-01 • 05/14/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
2 • Installing the Light Kit on a Non-Removable Switch Housing (cont.)
6. Align the locator posts in the switch housing cover with the
screw holes in the switch housing.
7. Align the threaded screw holes in the switch housing cover with
the threaded holes in the switch housing and install two screws.
8. Go to the instructions for Installing the Bulbs, Chains, and
Globe.
Attachment
Screw
Step 7
7
43545-01 • 05/14/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
3 • Installing the Light Kit on the Hunter Original
1. Uninstall the two screws from the switch housing plate.
NOTE: Save the switch housing cap should you choose to remove the light
fixture in the future.
2. Remove the wire connectors from the two wires in the switch housing
labeled “Connect Light Here” or “For Light Use.” One wire is white and the
other wire is black wire with a white stripe.
To connect the wires, hold the bare metal leads together and place a wire
connector over them, then twist the wire connector clockwise until tight.
Hunter Original
Connect the black wire with a white stripe from the switch housing to
the black wire from the light kit. Connect the white wire from the switch
housing to the white wire from the light kit. Secure all wire connections
using wire connectors.
CAUTION: Be sure no bare metal wires or wire strands are visible after
making the connections.
3. Ensure that the gasket is resting on the light kit mounting plate. Finish
attaching the light kit to the switch housing. Use the two screws removed
from the switch housing and the lock washers on the red tag. Partially
install the screws into the light kit, the gasket, and the housing. Rotate the
light fixture clockwise until the screws are locked into the narrow ends of
the keyhole slots. Securely tighten the two screws.
Screw
Switch
Housing
Plate
Step 1
4. Securely tighten the two screws.
5. Go to the instructions for Installing the Bulbs, and Globe.
WARNING: Improper installation
could cause the light fixture to
fall, or result in electrical shock or
personal injury.
Screw and
Washer
Steps 2-4
8
43545-01 • 05/14/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
4 • Installing the Bulbs, Chain, and Globe
1. First, install the included CFL medium-based bulbs.
2. Loosen the three thumbscrews on the lower edge of the light kit. Raise
the glass globe into the light kit. read the pull chain through the hole
in the center of the globe. Tighten the three thumbscrews.
3. e installation is complete and you can restore power to the ceiling
fan.
Globe
CFL Bulb
(included)
9
43545-01 • 05/14/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
5 • Troubleshooting
Light does not come on.
1. Make sure bulbs are installed properly.
2. Make sure breakers or fuses are on.
3. Verify that the light power lead is connected at the ceiling. Refer to
your ceiling fan manual for locating assembly and wiring.
Glass rattles.
1. Make sure the globe is secure.
If you need parts or service assistance, please call
888-830-1326 or visit us at our Web site at
Hunter Fan Company
7130 Goodlett Farms Pkwy. # 400
Memphis, Tennessee 38016
is Light Fixture Weighs 6 lbs.
Printed in China
10
43545-01 • 05/14/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
|