For Your Records and
Warranty Assistance
Type 3 Models
For reference, also attach your receipt or a copy
of your receipt to the manual.
Owner’s Guide and Installation Manual
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
Form# 45066-01
20100303
©2010 Hunter Fan Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing the Fan Site
Step 1 - Choose the Fan Site
Proper ceiling fan location and attachment to the building
structure are essential for safety, reliable operation, maximum
efficiency, and energy savings.
30” From
Wall or
8’ Minimum
Ceiling
Choose a fan site where:
Nearest
• No object can come in contact with the rotating fan blades during
normal operation.
Obstruction
7’ Minimum
Blades to
Floor
Height
• e fan blades are at least 7 feet above the floor and the ceiling is
at least 8 feet high.
• e fan blades have no obstructions to airflow, such as walls or
posts, within 30 inches of the fan blade tips.
• e fan is directly below a joist or support brace that will hold the
outlet box and the full weight of the fan.
Suitable Existing Fan Site
Checklist for Existing Fan Site
Fan Support
System
If you want to use an existing fan site, complete the following checklist to
determine if the site is acceptable and safe for your new Hunter fan. If you
cannot check off every item, prepare a new fan site as described on this
page.
Fan Support System
• Fan attaches directly to building structure.
• Fan support system will hold full weight of the fan and light kit.
Ceiling Hole
• e outlet box clearance hole is directly below the joist or support brace.
Outlet Box
• e outlet box is an UL-approved octagonal 4” x 1-1/2” outlet box (or as
specified by the support brace manufacturer).
• e outlet box is secured to the joist or support brace by wood screws
and washers through the inner holes of outlet box.
• e outer holes of the outlet box are aligned with joist or support brace.
• e bottom of the outlet box is recessed a minimum of 1/16” into
ceiling.
Outlet Box
Wiring
Fan Support
System
Wiring
• e electrical cable is secured to outlet box by an approved connector.
• Six inches of lead wires extend from outlet box.
If your existing fan site is suitable, skip ahead to Section 2 • Installing the
Ceiling Plate.
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing the Fan Site (continued)
Step 2 - Cut the Ceiling Hole
2-1. Locate the site for the ceiling hole directly below the joist or support brace that
will hold the outlet box and fan.
2-2. Cut a 4” diameter hole through the drywall or plaster of the ceiling. You will use
the hole to install the support brace and outlet box.
Step 3 - Install a Support Brace, If Necessary
Determine if there is a ceiling joist directly above the ceiling hole. If the joist is there,
determine if it is positioned to allow you to recess the outlet box a minimum of
1/16” into the ceiling. If NOT, install a support brace as follows:
3-1. Attach a 2” x 4” support brace between two joists. Position it to allow you to
recess the bottom of the outlet box a minimum of 1/16” into the ceiling.
Steps 2 – 3
3-2. Check the support brace to ensure it will support the full weight of the fan and
light kit.
Step 4 - Install the Outlet Box
4-1. Obtain a UL-approved octagonal 4” x 1-1/2” outlet box, plus two #8 x 1-1/2”
wood screws and washers, available from any hardware store or electrical supply
house.
4-2. Orient the outlet box so that both the inner and outer holes in the box align
with the joist or support brace.
4-3. Drill pilot holes no larger than the minor diameter of the wood screws (5/64”)
through the inner holes of the outlet box.
Step 4
4-4. Attach the outlet box directly to the support brace or joist with two #8 x 1-1/2”
wood screws and washers. e bottom of the outlet box must be recessed a
minimum of 1/16” into the ceiling.
Step 5 - Prepare the Wiring
5-1. Make sure the circuit breakers to the fan supply line leads and associated wall
switch location are turned off . If you cannot lock the circuit breakers in the
off position, securely fasten a prominent warning device, such as a tag, to the
service panel.
5-2. read the fan supply line through the outlet box so that the fan supply line
extends at least 6” beyond the box.
5-3. Attach the fan supply line to the outlet box with an approved connector,
available at any hardware store or electrical supply house.
5-4. Make certain the wiring meets all national and local standards and ANSI/NFPA
70.
Step 5
CAUTION: All wiring must be in
accordance with national and local
electrical codes and ANSI/NFPA 70. If
you are unfamiliar with wiring, use a
You have now successfully prepared your ceiling fan site. For instructions to install
your ceiling fan, go to your fan manual and continue with Section 2 • Installing the
Ceiling Plate.
qualified electrician.
4
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer’s Choice and Optional Accessories
Understanding Mounting and Installer’s Choice®
Support Brace
Hunter’s patented 3-position mounting system provides you maximum
installation flexibility and ease. You can install your Hunter fan in one
of three ways, depending on ceiling height and your preference: Low
Profile, Standard, or Angled mounting. e steps in this manual include
instructions for all three Installer’s Choice mounting methods.
Ceiling
Outlet Box
Standard
Mounting
Style
Considering Optional Accessories
Consider using Hunter’s optional accessories, including a wall-mounted
or remote speed control. To install and use the accessories, follow
the instructions included with each product. For quiet and optimum
performance of your Hunter fan, use only Hunter speed controls.
Standard Mounting hangs from the
ceiling by a downrod (included).
For ceilings higher than 8 feet, you can purchase
Hunter extension downrods. All Hunter fans use
sturdy 3/4” diameter pipe to assure stability and
wobble-free performance.
Support Brace
Ceiling
Outlet Box
Support Brace
8
CAUTION: To
reduce the risk of
personal injury, attach
the fan directly to the
12
Angled
Mounting
Style
support structure of
the building according
to these instructions,
and use only the
Low Profile
Mounting
Style
Ceiling
Outlet Box
hardware supplied.
Low Profile Mounting fits close to the
ceiling, recommended for ceilings less
than 8 feet high
Angled Mounting recommended for a
vaulted or angled ceiling
5
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
1 • Getting Ready
To install a ceiling fan, be sure you can do the following:
• Locate the ceiling joist or other suitable support in ceiling.
• Drill holes for and install wood screws.
• Identify and connect electrical wires.
• Lift 40 pounds.
If you need help installing the fan, your Hunter fan dealer can direct
you to a licensed installer or electrician.
Gathering the Tools
You will need the following tools for installing the fan:
• Electric drill with 9/64” bit
• Standard screwdriver (magnetic tip recommended)
• Phillips-head screwdriver (magnetic tip recommended)
• Wrench or pliers
• Ladder (height dependent upon installation site)
Installing Multiple Fans?
If you are installing more than
one fan, keep the fan blades and
blade irons (if applicable) in sets,
as they were shipped.
Checking Your Fan Parts
Carefully unpack your fan to avoid damage to the fan parts. Refer to
the included Parts Guide. Check for any shipping damage to the motor
or fan blades. If any parts are missing or damaged, contact your Hunter
dealer or call Hunter Technical Support Department at 888-830-1326.
(In Canada, call 866-268-1936).
Preparing the Fan Site
Before you begin installing the fan, follow all the instructions in
the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan
location and attachment to the building structure are essential for
safety, reliable operation, maximum efficiency, and energy savings.
6
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
2 • Installing the Hanger Bracket
2-1. Drill two pilot holes into the wood support structure through the
outermost holes in the outlet box. e pilot holes should be 9/64”
in diameter.
Isolator
Hanger
Bracket
Note: Your fan comes with four pre-installed neoprene noise
isolators.
2-2. read the lead wires from the outlet box down through the hole
in the middle of the hanger bracket.
2-3. Align the slotted holes in the hanger bracket with the pilot holes
you drilled in the wood support structure. For proper alignment
use slotted holes directly across from each other. If you are
installing the fan on an ANGLED ceiling, be sure to orient the
hanger bracket as shown in Illustration 2-3 (left or right view).
Note: e isolators should be flush against the ceiling.
2-4. Place a flat washer on each of the two 3” screws and pass the
screws through the slotted holes in the hanger bracket into the
pilot holes you drilled.
Tighten the screws into the 9/64” pilot holes; do not use lubricants
on the screws. Do not over tighten.
Flat Washer
Steps 2-2 – 2-4
Ceiling Peak
Ceiling Peak
Large
Opening
OR
Large
Opening
3” Screw
LEFT
RIGHT
Step 2-3 (Angled Ceiling Only)
7
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
3 • Assembling the Top Housing
Steps 3-1 – 3-2
3-1. To assemble the housing to the hanger adapter, align the three
Assembly Screw
raised tabs on the hanger adapter with the three narrow notches
Top
Housing
in the top housing. Make certain the housing sits flat on the
adapter.
3-2. Install three (3) assembly screws and washers and tighten them
securely.
Hanger Adapter
Washer
8
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
4 • Assembling and Hanging the Fan
You can assemble your fan for standard or angled mounting as shown
in steps 4-1 – 4-3. For low profile mounting (ceilings less than 8 feet
Steps 4-1 – 4-3
high), go to steps 4-6 – 4-9 on the next page.
Downrod
Canopy
4-1. To assemble fan to hang down from a flat or angled ceiling, place
the canopy and canopy trim ring around the adapter so that they
rest on the fan assembly.
4-2. Feed the wires from the fan through the downrod.
Canopy
Trim
Ring
Note: Make sure all the wires are on the same side of the metal
dowel pin inside the dowrod.
4-3. Loosen the square head setscrew on the adapter to install the pipe
and ball assembly. Note: When the pipe and ball assembly is fully
installed, 2-3 threads on the pipe will still be visible; this is normal.
Securely retighten the setscrew with a wrench or pliers.
Adapter
Setscrew
CAUTION: e adapter has a special coating on the threads. Do
not remove this coating; the coating prevents the downrod from
unscrewing. Once assembled, do not remove the downrod.
WARNING: Do not carry or lift fan by canopy.
4-4. Raise the fan and place the ball into the hanger bracket.
4-5. Align the notch on the ball with the indent in the hanger bracket.
(Rotate the fan until you hear the notch pop into place.)
Steps 4-4 –4-5
Go to 5 • Setting the remote wall control and receiver.
WARNING: Fan may fall if not assembled as directed in these
installation instructions.
Indent
9
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
4 • Assembling and Hanging the Fan (Low Profile Only)
You can assemble your fan for standard or angled mounting as shown
in steps 4-1 – 4-3 on the previous page. For low profile mounting
(ceilings less than 8 feet high), see steps 4-6 – 4-10 on this page.
4-6. Remove the screws from the hanger ball bracket.
4-7. Place the low profile washer from the parts sack into the canopy.
4-8. Place the canopy trim ring and canopy with washer on top of the
fan assembly.
4-9. Align the screw holes in the washer with the holes in the adapter.
Assemble securely with three #8-32 x 3/4” screws.
Step 4-6
4-10. Raise the fan and place the hook on the hanger bracket through
the round hole in the rim of the canopy.
(Not Actual Size)
WARNING: Fan may fall if not assembled as directed in these
installation instructions.
Steps 4-8 – 4-9
Low Profile Washer
Step 4-7 (Detail)
Low Profile Washer
Adapter
Canopy
Trim Ring
#8-32 x 3/4” Screw
Step 4-10
10
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
5 • Setting the Remote Wall Control and Receiver
Setting DIP switches
When two or more fans are located near each other, you may desire
to have the receiver/transmitter for each fan set to a different code,
so that the operation of one fan does not affect the operation of the
other fans.
Receiver DIP
switches
e DIP switches for the receiver are located on the flat surface of the
receiver. e DIP switches for the transmitter are in the the battery
compartment.
Face Cover
5-1. Press inward on each side of the wall control to remove the face
cover. Set the dip switches to match the dip switches in the
receiver.
IMPORTANT! Before you change the DIP switch settings, make
sure the battery is not connected to the transmitter.
Press
Inward
Change the position of the DIP switches in the remote transmitter
and the receiver. Make sure that the DIP switches match in
the remote receiver and transmitter. If they don’t match, the
transmitter will not function.
Wall Control
DIP Switches
5-2. Install a 12 Volt alkaline battery (A23, MN21, or equivalent).
5-3. Replace the face cover.
CAUTION: e remote control device
complies with part 15 of the FCC rules.
Changes or modifications not expressly
approved by Hunter Fan Company could void
your authority to operate this equipment.
Example DIP Switch Settings
Receiver 2
Receiver 1
Battery
Operation is subject to the following two
conditions:
DIP Switches
Set to 0100
DIP Switches
Set to 0111
1. is device may not cause harmful
interference.
Face Cover
Wall Control 1
Wall Control 2
2. is device must accept any interference
received, including interference that may
cause undesired operation.
WARNING: Use only the Hunter Fan
speed control supplied with this fan.
DIP Switches
Set to 0111
DIP Switches
Set to 0100
11
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
6 • Wiring the Fan
Receiver
6-1. Before attempting installation, make sure the power is still off.
A
6-2. To connect the wires, hold the bare metal leads together and place
a wire connector over them, then twist clockwise until tight. For all
these connections use the wire connectors provided.
B
CAUTION: Be sure no bare wire or wire strands are visible after making
connections.
6-3. Using a large wire connector, connect the ground wire from the
ceiling to the green wire from the ceiling plate and the green ground
wire from the downrod.
F
C
6-4. Using the large wire connectors, connect the white wire and the
black wire from the ceiling as follows:
E
D
Step 6-3
A • Ground/Green
•
e white (common) power wire from the ceiling to the white
wire from the receiver (marked on red tag “NEUTRAL IN”)
Step 6-4
B • Ceiling Black
• e black power wire from the ceiling to the black wire from the
receiver (marked on red tag “LIVE IN”)
• Receiver Black: “LIVE IN”
C • Ceiling White
6-5. Using the small wire connectors, connect the wires from the fan as
follows:
• Receiver White: “NEUTRAL IN”
Step 6-5
D • Fan Black/White
• Receiver Red: “LIGHT OUT”
E • Fan Black
• e black/white wire from the fan to the red wire from the
receiver (marked on white tag “LIGHT OUT”)
• e black wire from the fan to the black wire from the receiver
(marked on white tag “FAN OUT”)
• e white wire from the fan to the white wire from the receiver
(marked on white tag “COMMON OUT”)
• Receiver Black: “FAN OUT”
F • Receiver White: “COMMON OUT”
• Fan White
Steps 6-3 – 6-5
All wiring must be in accordance with
national and local electrical codes and
ANSI/NFPA 70. If you are unfamiliar with
wiring, use a qualified electrician.
6-6. Check each connection to make sure no bare wire or wire strands
are visible. Turn the splices upward and push them carefully back
through the ceiling plate into the outlet box.
6-7. Spread the wires apart, with the ground wires on one side of the
outlet box and the ungrounded wires on the other side of the outlet
box.
Large Wire Connector
6-8. Position the receiver in the canopy so that the antenna is close to
the edge of the ceiling plate for clear reception.
Small Wire
Connector
12
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
7 • Installing the Canopy and Canopy Trim Ring
Steps 7-1 – 7-2
Hanger Bracket
7-1. Partially install two canopy screws (about 2 full turns) in the
hanger bracket.
7-2. Raise the canopy over the hanger bracket. Align partially installed
screws with key slots in canopy.
7-3. Twist canopy clockwise to secure.
7-4. Install third & fourth canopy screw in round hole on canopy.
Securely tighten all four screws.
Canopy Trim
Ring
Canopy
7-5. Using both hands, push the canopy trim ring up to the top of the
canopy.
7-6. Twist canopy trim ring clockwise to secure the canopy.
Should you need to remove the canopy
trim ring, follow these steps:
1. Twist canopy trim ring counter
clockwise until it releases from
canopy.
Step 7-3
Step 7-4
Canopy
Screw
Step 7-5
13
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
8 • Assembling the Blades
Hunter fans use several styles of fan blade irons (brackets that hold the
blade to the fan).
8-1. Install the grommets into the blades by hand.
Step 8-1 (Detail)
8-2. Place each blade between a blade iron and medallion. Install three
blade assembly screws to attach the medallion to the blade iron.
Repeat for all blades.
8-3. For each blade, insert one blade iron armature screw through the
blade iron, and attach lightly to the fan. Insert the second blade
iron armature screw, then securely tighten both screws.
Blade Assembly
Screw
Grommet
Steps 8-2 – 8-3
Blade Iron
Armature
Screw
14
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
9 • Completing Your Installation With a Light Fixture
Your Hunter fan comes with an integrated light fixture assembly.
WARNING: Use only the light fixture supplied with this fan model.
9-1. To attach the light kit top housing, partially install two housing
assembly screws into the light kit mounting plate.
9-2. Feed the upper plug connector through the center opening of the
light kit top housing.
9-3. Align the keyhole slots in the housing with the housing assembly
screws.
9-4. Turn the light kit top housing counterclockwise until the housing
assembly screws are firmly situated in the narrow ends of the
keyhole slots. Install the remaining screw into the housing. Tighten
all three screws firmly.
Steps 9-1 – 9-3
Light Kit
Mounting
Plate
Light
Kit Top
Housing
Upper Plug
Connector
CAUTION: Make sure the light kit top housing is securely
attached to the light kit mounting plate. Failure to properly attach
and tighten all three assembly screws could result in the light kit top
housing and light fixture falling.
Housing
Assembly
Screw
15
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
9 • Completing Your Installation With a Light Fixture (Continued)
9-5. To attach the light kit, connect the upper plug connector from the
motor to the lower plug connector in the light kit.
Note: Both plug connectors are polarized and will only fit together
one way. Make sure the connectors are properly aligned before
connecting them. Incorrect connection could cause improper
operation and damage to the product.
Plug
Connector
9-6. Place the light kit over the light kit top housing. Align the holes
in the light kit top housing with the light kit. Attach the light kit
to the light kit top housing with three housing assembly screws.
Tighten all three screws firmly.
Housing
Assembly Screw
Steps 9-5 – 9-6
Light Kit
Note: In compliance with U.S. Federal energy regulations, this
ceiling fan contains a wattage saver that restricts the light
kit to a maximum of 190 Watts. Exceeding that limit or
the specifications on the light sockets may result in fire
hazard or improper operation. If lights do not appear to be
operating properly, see the troubleshooting section
Plug
Connector
Detail
Housing
Assembly Screw
16
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
9 • Completing Your Installation With a Light Fixture (Continued)
Installing the Glass Bowl
9-7. First install B10 candelabra bulbs (60
Watt Maximum) into the sockets.
9-8. Lift the glass bowl up to the light kit top
housing. Align the three tabs in the glass
bowl with the three slots in the light kit
top housing.
9-9. Rotate the glass bowl until the screw
holes in the light kit top housing line up
with the screw holes in the light kit.
9-10. Secure the glass bowl with three
decorative screws.
Slot
Decorative
Screw
Tab
Glass Bowl
Steps 9-8 – 9-10
Decorative
Screw
17
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
10 • Installing the Wall Control
10-1. Disconnect the existing switch and remove it
from the electrical box. Set the screws aside for
reuse.
10-2. Connect each wire from the wall to a lead from
the control. Use 2 of the wire connectors supplied
to make the connections. Refer to Figure 1.
10-3. Connect the ground wire from the control to the
earth/ground wire from the wall. Refer to Figure 1.
10-4. Gently push the wires and wall control into the
electrical box. Attach the control to the switch
box with the two screws provided.
10-5. Install a rocker-style faceplate (not included) with
the screws removed in Step 1.
Step 10-1
10-6. Restore power at main electrical panel.
ON/OFF
Figure 1
18
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
11 • Operating the Remote Control and Mounting the Holder
11-1. e wall control has individual buttons
for setting fan speed and light intensity.
Refer to the figure on the right.
Note: For best operation, start the fan
by pressing high, then select your desired
speed.
11-2. e light button turns the light. Push the
light button again to turn off the light.
Fan Light
11-3 To operate fan and light, push the on/
off switch to the position and press
the desired button on the wall control
keypad.
Fan Off
Fan Speed
Low
Fan Speed
Medium
Fan Speed
High
ON/OFF
19
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
12 • Operating and Cleaning Your Ceiling Fan
12-1. Ceiling fans work best by blowing air downward
(counterclockwise blade rotation) in warm weather to cool the
room with a direct breeze. In cold weather, having the fan draw
air upward (clockwise blade rotation) will distribute the warmer
air trapped at the ceiling around the room without causing a
draft.
12-2. For cleaning finishes, use a soft brush or lint-free cloth to prevent
scratching. A vacuum cleaner brush nozzle can remove heavier
dust. Remove surface smudges or accumulated dirt and dust
using a mild detergent and a slightly dampened cloth. You may
use an artistic agent, but never abrasive cleaning agents as they
In warm weather, use
downward air flow pattern
will damage the finish.
12-3. Clean wood finish blades with a furniture polishing cloth.
Occasionally, apply a light coat of furniture polish for added
protection and beauty. Clean painted and high-gloss blades in
the same manner as the fan finish.
To Change Airflow Direction
Turn the fan off and let it come to a complete stop. Press the reversing
switch on the fan. (You will need to remove the light kit glass to do so.)
Restart fan.
In cold weather, use upward
air flow pattern
Reversing
Switch
20
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
13 • Troubleshooting
Problem: Nothing happens; fan does not move.
1. Turn power on, replace fuse, or reset breaker.
2. Loosen canopy, check all connections according to the wiring the
fan section.
3. Check the plug connection in the light fixture.
4. Remove the shipping bumpers.
5. Make sure the receiver and remote are set to the same jumper
settings.
Problem: Noisy operation.
1. Tighten the blade assembly screws and blade iron armature screws
until snug.
2. Check to see if the blade is cracked. If so, replace all the blades.
Problem: Excessive wobbling.
1. If your fan wobbles when operating, use the enclosed balancing kit
and instructions to balance the fan.
2. Tighten all blade iron screws.
3. Turn power off, support fan very carefully, and check that the
hanger ball is properly seated.
Problem: Lights dim when turned on or do not turn on
1. Check to make sure wattage of light bulbs installed match the
specifications on the light socket.
Problem: If the light on this fan shuts off suddenly.
If you need parts or service assistance, please call
888-830-1326 (In Canada, call 866-268-1936) or
visit us at our Web site at
1. Turn the power to the fan off at the wall switch.
Wait 30 seconds, then resume power to the fan.
Hunter Fan Company
7130 Goodlett Farms Pkwy. #400
Memphis, Tennessee 38016
21
45066-01 • 03/03/10 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
|