1.888.830.1326
Table of Contents
What to Expect with
Your Installation
Congratulations on purchasing
Tools Needed
Ceiling Plate
Top Housing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
5
2
3
8
4
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
Canopy
Blades
Hanging the Fan
Wiring
To register your fan, please visit:
Save your receipt for proof of purchase.
7
11
9
Maintenance,
Operation & Cleaning
Switch Housing
Light Kit
Troubleshooting
?
?
?
12
15
17
18
1
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Tools Needed
Ladder
Wire Strippers
Screwdrivers
Power Drill
(optional)
9/64” Drill Bit
(optional)
If mounting to a support structure, you will also need these tools.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Ceiling Plate
Bumper
OFF
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes outlet box. Make sure
in support structure to aid it is securely installed
in securing ceiling plate and is acceptable for fan
Make sure all four (4) bumpers
are still attached.
with hardware found in
support of 31.8 kg (70
lbs) or less.
the
hardware bag.
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the
outlet box associated with the wall switch location.
Refer to warning w.1 on pg. 2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Top Housing
Top Housing
Trim Ring
Canopy
Adapter
Adapter
Thread the wires through the
top housing.
Place the top housing onto the
motor housing so that the holes
in the top housing lineup with
the holes in the motor housing
and the adapter.
Rest the trim ring on the top
housing.
Place the canopy on the top
housing. Ensure all four screw
holes line up with the screw
holes in both the top housing
and the adapter.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Top Housing (continued)
3/8”
8”
Grounding
Screw
Top Housing
Screws
Install the top housing screws. Install
the grounding screw in the smaller
screw hole. These screws can be found
in the hardware bag.
The wires can be cut, but leave at
least 8” extending from the top of
the canopy.
8”
3/8”
6
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Hanging the Fan
Ceiling
Plate
Hook
Ceiling
Plate Hook
Raise the fan and align the slots in the
canopy with the hooks on the ceiling plate.
Place the slots over the ceiling plate
hooks to hang the fan.
Note: To hang the fan, you must tilt the
canopy to an almost vertical position so that
the canopy slots sit on the ceiling plate hooks.
Note: Fan style may vary.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Wiring
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
M
I
N
O
R
G
F
Using an orange
wire connector from
the hardware
bag, connect the
grounding wires
(green, green/
For Dual Switches
Using the orange wire
connectors from the
hardware bag, connect
the white wire (grounded)
from the ceiling to the
white wire from the fan.
Connect the black wire
(ungrounded) from the
ceiling to the black wire
from the fan. Connect the
second (ungrounded) wire
from the ceiling to the blue
wire from the fan.
yellow stripe, or bare
copper) coming
from the ceiling and
ceiling plate.
For a Single Switch
Using the orange wire
connectors from the
hardware bag, connect the
black wire (ungrounded)
from the ceiling to the black
and the blue wires from the
fan. Connect the white wire
(grounded) from the ceiling to
the white wire from the fan.
F
N
M
O
A
I
M
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Canopy
Ceiling
Plate Hooks
Canopy
Screw
Canopy
Screw
Screw
Holes
Swing the fan up to align the canopy
screw holes with the mounting holes on
the ceiling plate.
Note: The slots in the canopy must
remain engaged while swinging the
canopy for alignment.
Hold the canopy up with the screw holes
aligned. Partially install two canopy
screws, found in the hardware bag, into
the holes opposite the ceiling plate hooks.
Partially install a canopy screw, found
in the hardware bag, between the
ceiling plate hooks. When all the holes
are properly aligned, securely tighten all
three canopy screws.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Canopy (continued)
Canopy
Trim Ring
Using both hands, push the canopy trim ring up
to the top of the canopy. The canopy trim ring will
snap and lock into place.
Note: Should you need to remove the trim ring,
press firmly on opposite sides of the trim ring. The
tabs will flex out releasing the canopy trim ring.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Blades
Secure each blade to a blade iron as shown
using the blade nuts, found in the hardware
bag, and the blade assembly screws, found in
the hardware bag.
Lightly attach the blade irons to the motor with
the blade iron armature screws, found in the
hardware bag, then securely tighten after all
screws are attached.
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the finishes.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Switch Housing
Screw two (2) housing assembly screws
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws
and twist counterclockwise.
Remove the pre-installed screw and red
label from the switch housing.
SAVE THE SCREW.
Note: The screw was installed for
shipping purposes only.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Switch Housing (continued)
Switch
Housing
Screw
Switch Housing
Screw
Lower Switch
Housing
Insert the third screw, found in the
hardware bag, into place and then
tighten all three (3) screws.
To attach the lower switch housing,
partially install three switch housing screws
into the standoffs as shown, leaving the
circled standoff empty.
Connect the plugs from the upper and
lower switch housings. Make sure to line up
the colored markings on the connectors.
Make sure the upper switch housing is securely attached
to the mounting plate. Failure to properly secure all 3 assembly
screws could result in the switch housing fixture falling.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Switch Housing (continued)
Plate Screw
Lower Switch
Housing
Align the keyhole slots in the lower
switch housing with the stand off screws.
Turn the housing counterclockwise until
the standoff screws are firmly situated in
the narrow end of the keyhole slots.
Remember the screw you saved? Install
it back into the housing. Tighten all four
screws firmly.
Remove the two pre-installed plate
screws from the switch housing.
Save the screws
14
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Light Kit
Hood
Bulb
Cover Plate
Plate Screw
Wire Basket
Lift the cover plate, aligning the screw
holes with the screw holes in the switch
housing. Install the plate screws to secure
the cover plate to the switch housing.
Install one E-26 60-watt light bulb.
When necessary, replace with bulb of
the same wattage.
Align the holes in the wire basket and
the hood with the holes on the rim of the
upper switch housing. Install four switch
housing screws, found in the hardware
bag, through wire basket and hood into
the upper switch housing.
Make sure the light kit is securely attached to the upper
switch housing. Failure to properly secure all three assembly
screws could result in the light fixture falling.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Light Kit (continued)
Light
Fan
Pull
Chain
Pull
Chain
Connect the appropriate pull chain
pendant to each of the short chains
coming from the switch housing.
See next page for fan
operation instructions.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Maintenance, Operation, & Cleaning
Fan Pull
Chain
Light Pull
Chain
ON
Reverse
Switch
Cleaning the fan - Use soft
brushes or cloths to prevent
scratching. Cleaning products
may damage the finishes.
To switch the direction of air
flow, move the reverse switch to
the opposite position.
The fan pull chain controls the
speed: from high to off.
The light pull chain controls the
light fixture: on and off.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
1.888.830.1326
Troubleshooting
Fan doesn’t work
Excessive wobbling
Noisy operation
• Make sure power switch is on.
• Make sure the blades are
securely attached to the
blade irons according to the
blade assembly instructions
provided.
• Check to see if any of the blades
are cracked. If so, replace all of
the blades.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Use the provided balancing
kit and instructions to
balance the fan.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 8.
Lights dim when turned on or
do not turn on at all.
• Make sure the wattage of the
light bulbs installed matches
the specifications on the light
sockets.
• Check the plug connection in
the switch housing.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
M3559-01 • 11/12/14 • © Hunter Fan Company
|