1.888.830.1326
Table of Contents
What to Expect with
Your Installation
Congratulations on purchasing
Preparation
Tools Needed
Ceiling Bracket
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
5
2
3
7
4
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
Hanging the Fan
Wiring
Motor Housing
Maintenance,
Blades
To register your fan, please visit:
Save your receipt for proof of purchase.
6
9
8
Switch Housing
Light Kit
Operation & Cleaning
Troubleshooting
?
?
?
10
11
13
14
1
Download from Www.Somanuals.com. All Manuals Search And Download.
M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.888.830.1326
Tools Needed
9/64” Drill Bit
(optional)
Power Drill
(optional)
Screwdrivers
Ladder
If mounting to a support structure, you will also need these tools.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.888.830.1326
Ceiling Bracket
Bumper
OFF
Use wood screws
Use machine screws
(included) when securing
to support structure with
(provided with outlet
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
in support structure to aid
outlet box. Make sure
it is securely installed
Make sure all four bumpers are still attached.
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the
outlet box associated with the wall switch location.
Refer to warning w.1 on pg. 2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.888.830.1326
Hanging the Fan
Ground
Wire
Screw
Hole
Locking
Screw
While holding the wires out of the way, lift
the motor assembly and place the square
hanger into the opening in the ceiling
bracket. Be sure the ground wire attached
to the hanger faces out of the large
opening in the ceiling bracket.
Once the motor is in the ceiling
bracket, use the two locking screws
found in the
hardware bag to secure
the motor to the ceiling bracket.
Note: Fan style may vary.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.888.830.1326
Wiring
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
M
I
N
O
R
G
F
For Dual Switches
Using orange wire
connectors from
Green/Yellow
Stripe
the
hardware bag,
connect the white wire
(grounded) from the
ceiling to the white wire
from the fan.
For a Single Switch
Using an orange wire
connector from
Using the orange wire
connectors from
the
hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
ceiling, fan, and hanging
bracket.
the
hardware bag, connect
Connect the black wire
(ungrounded) from the
ceiling to the black wire
from the fan. Connect the
second (ungrounded) wire
from the ceiling to the blue
wire from the fan.
the black wire (ungrounded)
from the ceiling to the black
and the blue wires from the
fan. Connect the white wire
(grounded) from the ceiling to
the white wire from the fan.
F
N
O
A
M
M
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.888.830.1326
Motor Housing
Notch
Motor
Housing
Screw
Screw
Holes
Indentation
Raise the motor housing up over the motor
and ceiling bracket. Turn the motor housing
so the screw holes align and the indentation
in the housing locks into place with the notch
in the ceiling bracket. The motor housing is
not secured until the next step is complete.
Do not leave unattended.
With a Phillips head screwdriver, install
the four motor housing screws found
in the
hardware bag. Tighten all four
screws securely.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.888.830.1326
Blades
Insert grommets found in the
hardware
Lightly attach the blade irons to the
motor with screws found in
bag into the holes in the blades, then
secure each blade to a blade iron with
the
hardware bag, then securely
screws found in the
hardware bag.
tighten after both screws are attached.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.888.830.1326
Switch Housing
Screw two housing assembly screws from
the hardware bag halfway into the
motor housing. It does not matter which
two screw holes you choose.
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
Insert the third screw, found in
the
hardware bag, into place and
then tighten all three screws.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all three assembly screws could result in the
switch housing fixture falling.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.888.830.1326
Light Kit
Notch
Switch
Housing
Screw
Switch
Housing
Screw
Align the notches in the sides of the lower
switch housing with the upper switch
Install the third switch housing screw.
Tighten all three screws securely.
Partially install two of the switch housing
screws found in the
bag. Connect
housing screws. Lift the lower switch housing.
Twist the lower switch housing clockwise
to lock into place. Then thread the fan
pull chain through the hole in the light kit.
the plugs from the upper and lower
switch housings. Make sure to line up the
colored markings on the connectors.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
assembly screws could result in the light fixture falling.
Want to install your fan without a light kit?
“How do I install my fan without the light kit?”
11
Download from Www.Somanuals.com. All Manuals Search And Download.
M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.888.830.1326
Light Kit (continued)
Metal
Plate
Fan
Pull
Chain
Light
Pull
Chain
Globe
Globe
Keeper
Finial
Cap
Finial
Press the globe and globe keeper
flush against the metal plate. Thread
the light pull chain through the hole
in the center of the finial cap and
thread the fan pull chain through the
hole in the side of the cap. Finally,
thread only the light pull chain
Connect the appropriate pull
chain pendant to each of the short
chains coming from the finial
and finial cap. The fan pull chain
controls the speed: from high to
off. The light pull chain controls
the light fixture: on and off.
Install a bulb into each of
the sockets. When necessary,
replace with bulbs of the same
type and wattage.
See next page for fan
operation instructions.
through the hole in the finial and
screw the finial onto the threaded rod.
Note: Glass shade style and number of lights may vary.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.888.830.1326
Maintenance, Operation & Cleaning
Metal
Plate
ON
Globe
Globe
Keeper
Finial
Cap
Reverse
Switch
Finial
Changing the direction of air
flow - move the reverse switch
to the opposite position.
Cleaning the fan - use soft
brushes or cloths to prevent
scratching. Cleaning products
may damage the finishes.
Changing the bulbs - unscrew
the finial and remove it from the
threaded rod. Remove the finial cap
and unscrew the globe keeper while
supporting the globe with your other
hand. Carefully remove the globe.
Unscrew bulbs and replace with
bulbs of same type and wattage.
Reinstall the globe assembly.
For questions regarding removing a light kit, call
customer service 1-888-830-1326.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.888.830.1326
Troubleshooting
Fan doesn’t work
Noisy Operation
Excessive wobbling
• Make sure power switch is on.
• Tighten the blade and blade
iron screws until they are snug.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Pull the pull chain to make sure
it is on.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Use the provided balancing
kit and instructions to balance
the fan.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 7.
• Check the plug connection in
the switch housing.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
|