1.888.830.1326
Table of Contents
What to Expect with
Your Installation
Congratulations on purchasing
Tools Needed
Mounting Options
Ceiling Bracket
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
2
3
9
4
5
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
Downrod
Wiring
Canopy
Blades
To register your fan, please visit:
Save your receipt for proof of purchase.
6
10
11
Maintenance
& Cleaning
Light Kit
Troubleshooting
?
?
?
12
14
15
1
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
1.888.830.1326
Tools Needed
Pliers
Wire Strippers
Screwdrivers
Ladder
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
O
34
CEILING
Mounting Options
If you have a flat ceiling:
Hang your fan by a standard downrod (included).
Standard
Mounting
Support
Structure
Support
Structure
If you have an angled ceiling:
Ceiling
Outlet Box
(required)
1. You will need a longer downrod (sold separately).
Angled
Mounting
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Ceiling
Outlet Box
(required)
Standard
Mounting
Style
Angled
Mounting
Style
Use the three steps below to determine if your ceiling angle is greater than 34°
1
2
3
34°
PLACE
SLIDE
toward ceiling
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
Guide Touches
but NOT Ceiling
Wall
Use Standard Mounting
or Low-Profile Mounting
Use Angled Mounting
to hang the fan from a
to hang the fan from a flat ceiling.
vaulted or angled ceiling.
You need BOTH
a Longer
You need ONLY
a Longer
Downrod &
an Angled
Downrod
Mounting Kit
*most common
4
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
1.888.830.1326
Ceiling Bracket
OFF
Make sure all four (4)
bumpers are still attached.
For angled ceilings, point
opening toward peak.
Use wood screws
(included) when securing
to support structure with
Use machine screws
(provided with outlet
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
in support structure to aid
outlet box. Make sure
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to
the outlet box associated with the wall switch location.
Refer to warning w.1 on pg. 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
1.888.830.1326
Downrod
Standard
skip to next page
Downrod
for ceilings 8-10’ high
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
1
2
3
4
5
Shorter
Downrod
for fans installed
close to ceiling
10
9
8
7
6
Steps 6-10 to reassemble with new pipe
6
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
1.888.830.1326
Downrod (continued)
Remove the pre-installed
setscrew so that the downrod
can be inserted.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
8”
3/8”
If the setscrew is not tightened
securely, the fan may fall.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
1.888.830.1326
Downrod (continued)
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
1.888.830.1326
Wiring
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
M
I
N
O
R
G
F
For Dual Switches
Using orange wire
connectors from
Green/Yellow
Stripe
the
hardware bag,
connect the white wire
(grounded) from the
ceiling to the white wire
from the fan.
For a Single Switch
Using an orange wire
connector from
Using the orange wire
connectors from
the
hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
ceiling, downrod, and
hanging bracket.
the
hardware bag, connect
Connect the black wire
(ungrounded) from the
ceiling to the black wire
from the fan. Connect the
second (ungrounded) wire
from the ceiling to the blue
wire from the fan.
the black wire (ungrounded)
from the ceiling to the black
and the blue wires from the
fan. Connect the white wire
(grounded) from the ceiling to
the white wire from the fan.
F
N
A
O
M
M
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
1.888.830.1326
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
Lift the canopy into place so that
the screw holes are aligned.
Insert the two canopy screws
found in the
hardware bag.
the hanging bracket as shown.
Note: Fan style may vary.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
1.888.830.1326
Blades
Blade
Holes
Blade
Iron Post
Align the three holes in the blade with the
three blade iron posts. Squeeze the blade and
the blade post together.
The flared tops of the blade iron posts
will be fully visible above the blade when
properly assembled.
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the finishes.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
1.888.830.1326
Light Kit
Switch
Housing
Screw
Switch
Housing Notch
Screw
Align the notches in the sides of the lower
switch housing with the screws on the upper
switch housing. Twist the lower switch
housing clockwise to lock into place.
Install the third switch housing screw.
Tighten all three screws securely.
Partially install two of the switch housing
screws found in the
bag. Connect the
plugs from the upper and lower switch
housings. Make sure to line up the colored
markings on the connectors.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
assembly screws could result in the light fixture falling.
Want to install your fan without a light kit?
“How do I install my fan without the light kit?”
12
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
1.888.830.1326
Light Kit (continued)
Thumb Screw
Shade
Connect a pull chain pendant to
each of the short chains coming
from the switch housing.
To install the shade, first loosen
the thumb screws. Raise the
shade to the light fixture. Tighten
all thumbscrews securely.
Install a bulb into each of
the sockets. When necessary,
replace with bulbs of the same
type and wattage.
See next page for fan
operation instructions.
Note: In compliance with US federal energy regulations, this ceiling
fan contains a device that restricts its light output. Exceeding the
wattage limit marked on the MAX wattage sticker affixed to the
light socket(s) may result in fire hazard or improper operation.
Note: Glass shade style and number of lights may vary.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
1.888.830.1326
Maintenance & Cleaning
Fan Pull
Chain
Light Pull
Chain
ON
Reverse
Switch
The fan pull chain controls the
speed: from high to off.
To switch the direction of air
flow, move the reverse switch to
the opposite position.
For cleaning the fan, use soft
brushes or cloths to prevent
scratching. Cleaning products
may damage the finishes.
The light pull chain controls the
light fixture: on and off.
For questions regarding removing a light kit, call
customer service at 1-888-830-1326.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
1.888.830.1326
Troubleshooting
Fan doesn’t work
Noisy Operation
Lights dim when turned on or
do not turn on at all.
Excessive wobbling
• Make sure power switch is on.
• Tighten the blade and blade
iron screws until they are snug.
• Make sure that the blades
are properly installed on the
blade iron posts.
• Make sure the wattage of the
light bulbs installed matches
the specifications on the light
sockets.
• Pull the pull chain to make sure
it is on.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Use the provided balancing
kit and instructions to balance
the fan.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 9.
• Check the plug connection in
the switch housing.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
M0006-01 • 04/14/14 • © Hunter Fan Company
|