10” Opal Schoolhouse Globe Light Kit
Installation Instructions
43506-01 r032907
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Light Kit on Fans with Removable Switch Housings
1. Unscrew the three screws from the upper switch housing. Disconnect
the 9-pin plug connectors. Remove the lower switch housing.
I
O
2. Push the plug button from inside the lower switch housing to remove
the plug button and switch housing cap. Unscrew the two attachment screws on the
bottom of the switch housing.
NOTE: Save the plug button and switch housing cap should you choose to remove
the light fixture in the future.
3. Feed the two wires from the light kit up through the center hole in the lower switch
housing.
Removable Switch Housing
CAUTION: If your fan is operated by remote control, take care not to damage
the small components on the circuit board inside the housing.
Align the keyholes of the light kit and the screw holes of the lower switch housing.
Install the nut and washer onto the threaded rod from the light kit.
9-Pin Plug
Connector
Finish attaching the light kit to the lower switch housing. Use the two attachment
screws removed from the lower switch housing and the lock washers on the red
tag. Partially install the screws into the light kit and the housing. Rotate the housing
counterclockwise until the screws are locked into the narrow ends of the keyhole
slots. Securely tighten the two screws.
Screw
Attachment
Screw
WARNING: Improper installation could cause the light fixture to fall, or result
in electrical shock or personal injury.
Lower Switch
Housing
Steps 1–2
Plug
4. Remove the wire nuts from the two wires in the switch housing labeled “Connect
Light Here” or “For Light Use.”
Connect the black/white striped wire from the switch housing to the black wire from
the light kit. Connect the white wire from the switch housing to the white wire from
the light kit. Secure all wire connections using wire nuts.
To connect the wires, hold the bare metal leads together and place a wire nut over
them, then twist the wire nut clockwise until tight.
CAUTION: Be sure no bare metal
wires or wire strands are visible after
making the connections.
Wires and
Wire Nuts
5. Reconnect the 9-pin plug connector.
6. Install screws to reattach the lower
switch housing to the upper switch
housing.
Attachment
Screws and
Lockwashers
7. Go to the instructions for Installing
the Bulbs, Chains, and Globe.
9-Pin Plug
Connector
Step 3
Screw
Steps 4–6
43506-01 r032907
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Light Kit on Fans with Non-Removable Switch Housing
1. Uninstall the two screws from the switch housing cover.
I
O
2. Remove the plug or screw from the center of the switch housing
cover.
3. read the switch housing cover onto the wires from the light kit. Align the large
ends of the keyholes in the light kit with the screw holes in the switch housing cover.
Install the nut and washer onto the threaded rod from the light kit to secure the
switch housing cover.
4. Finish attaching the light kit to the switch housing cover. Use the two attachment
screws removed from the lower switch housing and the lock washers on the red
tag. Partially install the screws into the light kit and the housing. Rotate the housing
counterclockwise until the screws are locked into the narrow ends of the keyhole
slots. Securely tighten the two screws.
Non-Removable Switch Housing
WARNING: Improper installation could cause the light fixture to fall, or result
in electrical shock or personal injury.
5. Remove the wire nuts from the two wires in the switch housing labeled “Connect
Light Here” or “For Light Use.” One wire is white and the other wire is black/white
striped.
Switch
Housing
Cover
Connect the black/white striped wire from the switch housing to the black wire from
the light kit. Connect the white wire from the switch housing to the white wire from
the light kit. Secure all wire connections using wire nuts.
To connect the wires, hold the bare metal leads together and place a wire nut over
them, then twist the wire nut clockwise until tight.
Steps 1–2
Screw
Plug
CAUTION: Be sure no bare metal wires
or wire strands are visible after making the
connections.
Switch
Housing
Cover
Nut and
Washer
6. Align the locator posts in the switch housing
cover with the screw holes in the switch
housing.
Screw
Hole
7. Align the threaded screw holes in the switch
housing cover with the threaded holes in the
switch housing and install two screws.
8. Go to the instructions for Installing the Bulbs,
Chains, and Globe.
Wires and
Wire Nuts
Light Kit
Mounting
Plate
Steps 5–7
Steps 3–4
ꢂ
43506-01 r032907
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Light Kit on Fans With Non-Removable Switch Housing
and No Center Hole
I
O
1. Uninstall the two screws from the switch housing.
2. Remove the wire nuts from the two wires in the switch housing labeled
“Connect Light Here” or “For Light Use.” One wire is white and the other wire is
black/white striped.
Connect the black/white striped wire from the switch housing to the black wire from
the light kit. Connect the white wire from the switch housing to the white wire from
the light kit. Secure all wire connections using wire nuts.
To connect the wires, hold the bare metal leads together and place a wire nut over
them, then twist the wire nut clockwise until tight.
Hunter original and non-
removable switch, no center hole
CAUTION: Be sure no bare metal wires or wire strands are visible after making
the connections.
3. Finish attaching the light kit to the switch housing. Use the two screws removed
from the switch housing and the lock washers on the red tag. Partially install the
screws into the light kit and the housing. Rotate the light fixture clockwise until the
screws are locked into the narrow ends of the keyhole slots. Securely tighten the two
screws.
WARNING: Improper installation could cause the light fixture to fall, or result
in electrical shock or personal injury.
4. Go to the instructions for Installing the Bulbs, Chains, and Globe.
Wires and
Wire Nuts
Screws
and
Screw
Washers
Switch
Housing
Plate
Light Kit
Mounting Plate
Step 3
Step 1
Step 2
43506-01 r032907
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Bulbs, Chains, and Globe
1. Install one 19-watt compact fluorescent light bulb (included) into the socket.
2. Loosen the three thumb screws in the light kit. Raise the glass globe to the light
fixture, fitting the rim into the louvered edge. Ensure that the top edge of the globe
clears the screws. Hand tighten the thumb screws.
3. Attach the provided breakaway connector onto the end of the pull chain.
4. e installation is complete and you can restore power to the ceiling fan.
Steps 1–4
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
Troubleshooting
For other problems or questions, contact the
Light does not come on.
Hunter Fan Company Technical Support at
US 888-830-1326 / Canada 866-268-1936.
1. Make sure bulbs are installed properly and filament is not blown.
2. Make sure breakers or fuses are on.
3. Verify that the light power lead is connected at the ceiling. Refer to
your ceiling fan manual for locating assembly and wiring.
Glass rattles.
1. Make sure the glass globe is secure.
© 2007 Hunter Fan Company
Printed in China
43506-01 r032907
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
|