For Your Records and
Warranty Assistance
Type 2 Models
For reference, also attach your receipt or a copy
of your receipt to the manual.
Owner’s Guide and Installation Manual
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
Form# 42676-01
20090513
©2009 Hunter Fan Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer’s Choice and Optional Accessories
Understanding Mounting and Installer’s Choice®
Support Brace
Hunter’s patented 3-position mounting system provides you maximum
installation flexibility and ease. You can install your Hunter fan in one
of three ways, depending on ceiling height and your preference: Low
Profile, Standard, or Angled mounting. e steps in this manual include
instructions for all three Installer’s Choice mounting methods.
Ceiling
Outlet Box
Standard
Mounting
Style
Considering Optional Accessories
Consider using Hunter’s optional accessories, including a wall-mounted
or remote speed control. To install and use the accessories, follow
the instructions included with each product. For quiet and optimum
performance of your Hunter fan, use only Hunter speed controls.
Standard Mounting hangs from the
ceiling by a downrod (included).
For ceilings higher than 8 feet, you can purchase
Hunter extension downrods. All Hunter fans use
sturdy 3/4” diameter pipe to assure stability and
wobble-free performance.
Support Brace
Ceiling
Outlet Box
Support Brace
8
CAUTION: To
reduce the risk of
personal injury, attach
the fan directly to the
12
Angled
Mounting
Style
support structure of
the building according
to these instructions,
and use only the
Low Profile
Mounting
Style
Ceiling
Outlet Box
hardware supplied.
Low Profile Mounting fits close to the
ceiling, recommended for ceilings less
than 8 feet high
Angled Mounting recommended for a
vaulted or angled ceiling
3
42676-01 • 05/13/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
1 • Getting Ready
To install a ceiling fan, be sure you can do the following:
• Locate the ceiling joist or other suitable support in ceiling.
• Drill holes for and install wood screws.
• Identify and connect electrical wires.
• Lift 40 pounds.
If you need help installing the fan, your Hunter fan dealer can direct
you to a licensed installer or electrician.
Gathering the Tools
You will need the following tools for installing the fan:
• Electric drill with 9/64” bit
• Standard screwdriver (magnetic tip recommended)
• Phillips-head screwdriver (magnetic tip recommended)
• Wrench or pliers
• Ladder (height dependent upon installation site)
Installing Multiple Fans?
If you are installing more than
one fan, keep the fan blades and
blade irons (if applicable) in sets,
as they were shipped.
Checking Your Fan Parts
Carefully unpack your fan to avoid damage to the fan parts. Refer to
the included Parts Guide. Check for any shipping damage to the motor
or fan blades. If any parts are missing or damaged, contact your Hunter
dealer or call Hunter Technical Support Department at 888-830-1326
(In Canda, call 866-268-1936).
Preparing the Fan Site
Before you begin installing the fan, follow all the instructions in
the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan
location and attachment to the building structure are essential for
safety, reliable operation, maximum efficiency, and energy savings.
4
42676-01 • 05/13/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
2 • Installing the Ceiling Plate
CAUTION: To avoid possible electrical shock, before installing your fan,
Toward
Ceiling Peak
disconnect the power by turning off the circuit breakers to the outlet box
and associated wall switch location. If you cannot lock the circuit breakers
in the off position, securely fasten a prominent warning device, such as a
tag, to the service panel.
2-1. Drill two pilot holes into the wood support structure through the
outermost holes in the outlet box. e pilot holes should be 9/64”
in diameter.
For Angled Ceilings: Be sure to orient the ceiling plate so that the
two tabs are pointing toward the ceiling peak.
For Angled Ceilings: Be sure to orient
the ceiling plate so that the two tabs
are pointing toward the ceiling peak.
2-2. Your fan comes with four preinstalled noise isolators. Check to
make sure all four isolators are in place and were not removed
during shipment.
2-3. Place a flat washer on each of the two 3” wood screws.
2-4. read the supply wires from the outlet box in the ceiling through
the hole in the center of the ceiling plate.
2-5. Align the slotted holes in the ceiling plate with the pilot holes you
drilled in the wood support structure. For proper alignment use
slotted holes directly across from each other.
Note: e isolators should be flush against the ceiling.
2-6. Pass the screws through the slotted holes in the ceiling plate into
the pilot holes you drilled.
Tighten the screws into the 9/64” pilot holes; do not use lubricants
on the screws. Do not over tighten.
Ceiling
Plate
Flat Washer
3” Wood
Screw
Steps 2-3 – 2-6
5
42676-01 • 05/13/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
3 • Assembling and Hanging the Fan
WARNING: Fan may fall if not assembled as directed in these
Standard or Angled Mounting
installation instructions.
Steps 3-2 – 3-3
3-1. Unbundle the wires from the fan.
Downrod
For Standard or Angled mounting:
3-2. Insert the downrod through the canopy and canopy trim ring.
Feed the wires from the fan through the downrod on one side of
the pin in the ball.
Canopy
Canopy
Trim Ring
3-3. Loosen the square head setscrew on the adapter to install the pipe
and ball assembly. Note: When the pipe and ball assembly is fully
installed, 2-3 threads on the pipe will still be visible; this is normal.
Securely retighten the setscrew with a wrench or pliers. Skip to
step 3-7.
Setscrew
Low Profile Mounting
CAUTION: e adapter has a special coating on the threads. Do
not remove this coating; the coating prevents the downrod from
unscrewing. Once assembled, do not remove the downrod.
Steps 3-5 – 3-6
Low Profile Screws
Low Profile
Washer
Green
Ground
Wire
For Low Profile mounting:
Note: For low profile mounting, the downrod is replaced with the
low profile washer.
Canopy
Trim Ring
Canopy
3-4. Remove the setscrew from the adapter.
3-5. Place the low profile washer into the canopy with the lip down.
3-6. Align the holes in the washer with the holes in the adapter.
Assemble securely with three low profile screws.
Low Profile Screw
Hanging the Fan:
Step 3-6 (Detail)
Note: To hang the fan, you must tilt the canopy to an almost vertical
position so that the canopy slots sit on the ceiling plate hooks.
Low Profile Screw
Adapter
3-7. Raise the fan and align the slots in the canopy with the hooks on
the ceiling plate.
Low Profile
Washer
3-8. Place the slots over the hooks to hang the fan.
6
42676-01 • 05/13/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
4 • Wiring the Fan
All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualified electrician.
Wall switches are not included. Select an acceptable general-use switch
in accordance with national and local electrical codes.
Wire
Connector
4-1. Before attempting installation, make sure the power is still off.
Wattage
Saver
4-2. To connect the wires, hold the bare metal leads together and place
a wire connector over them, then twist clockwise until tight. For
all these connections use the wire connectors provided.
Dual Switch
Wiring
4-3. Connect the bare or green ground wire from the ceiling to the
green ground wire from the ceiling plate and the green ground
wire from the fan.
4-4. Connect the white wire from the ceiling to the white wire from
the wattage saver (marked on red tag “NEUTRAL IN”).
4-5. Connect the white wire from the fan to the other white wire from
the wattage saver (marked on white tag “COMMON OUT”).
4-6. Connect the black with a white stripe wire from the fan to the red
wire from the wattage saver (marked on white tag “LIGHT OUT”).
4-7. Connect the remaining wires as follows:
Dual Switch Wiring:
• e black wire from the ceiling to the black wire from the fan
• e black wire from the wattage saver (marked on red tag
“LIVE IN”) to the wire for the wall switch.
Single Switch Wiring
Wattage
Saver
Single Switch Wiring:
• e black wire from the ceiling to the black wire from the fan
and the black wire from the wattage saver (marked on red tag
“LIVE IN”).
CAUTION: Be sure no bare wire or wire strands are visible after
making connections.
4-8. Turn the splices upward and push them carefully back through the
ceiling plate into the outlet box.
4-9. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the
outlet box.
7
42676-01 • 05/13/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
5 • Installing the Canopy and Canopy Trim Ring
WARNING: Failure to complete the following steps could cause the fan
Step 5-1
to fall.
Note: It is recommended you use a magnetic tip screwdriver for the
following steps.
Tab
5-1. Rotate the hanger ball so the tab in the canopy is secure in the
hanger ball groove. Note: Your fan may have multiple tabs and
grooves that must be aligned.
Groove
5-2. Swing the fan up to align the canopy screw holes with the
mounting holes on the ceiling plate.
Step 5-2
WARNING: e slots in the canopy must remain engaged while
swinging the canopy for alignment.
5-3. Holding the canopy up with the screw holes aligned, partially
install two canopy screws into the holes opposite the ceiling plate
tabs.
5-4. Partially install a canopy screw into the hole between the two
ceiling plate tabs.When all the holes are properly aligned, securely
tighten all three canopy screws.
5-5. Verify that the tabs in the canopy are still in the grooves of the
hanger ball.
Step 5-3
5-6. Align the tabs on the trim ring opposite the grooves in the hanger
ball. Using both hands, push the canopy trim ring up to the top of
the canopy. e canopy trim ring will snap and lock into place.
Canopy
Note: Should you need to remove the trim ring, press firmly on
opposite sides of the trim ring directly above the groove in the
hanger ball. e tabs will flex out releasing the canopy trim ring.
Canopy
Trim
Ring
Canopy Screw
8
42676-01 • 05/13/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
6 • Assembling the Blades
Hunter fans use several styles of fan blade irons (brackets that hold the
blade to the fan).
6-1. Your fan may include blade grommets. If your fan has grommets,
insert them by hand into the holes on the blades.
Step 6-1 (Detail)
6-2. Attach each blade to a blade iron using three blade assembly
screws. If you used grommets, the blades may appear slightly loose
after screws are tightened. is is normal.
6-3. Remove the blade mounting screws and rubber shipping bumpers
from the motor. Note: Some blade mounting screws are installed
in the motor to secure shipping blocks.
6-4. For each blade, insert one blade mounting screw through the
blade iron, and attach lightly to the fan. Insert the second blade
mounting screw, then securely tighten both mounting screws.
Grommet
Steps 6-1 – 6-2
Blade Assembly
Screws
Use with grommet
Use without grommet
Blade
Mounting
Screw
Step 6-4
9
42676-01 • 05/13/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
7 • Completing Your Installation With or Without a Bowl Light Fixture
Your Hunter fan comes with an integrated light fixture assembly and an
optional switch housing cap and plug button. is feature gives you the
option of installing the fan with OR without the included light fixture.
e steps below direct you whether or not you are installing a light
fixture.
.WARNING: Use only the light fixture supplied with this fan model.
7-1 . If you want to install the light fixture, proceed with step 7-2
now.
. . If you do not want to install the light fixture, you need to
uninstall it now. See “Uninstalling the Light Fixture” on page 11.
Once you have uninstalled the light fixture, continue with step
7-2
7-2. To attach the lower switch housing, connect the upper plug
connectors from the motor to the lower plug connectors in the
lower switch housing assembly.
. . Note: Both plug connectors are polarized and will only fit together
one way. Make sure the connectors are properly aligned before
connecting them. Incorrect connection could cause improper
operation and damage to the product.
7-3. Place the lower switch housing assembly over the upper switch
housing. Align the side screw holes in the upper and lower switch
housings. Attach the lower switch housing to the upper switch
housing with two #6-32 x 7/8” housing assembly screws.
If you are not installing the light fixture, your installation is
complete. Otherwise, proceed with step 7-4.
Housing
Assembly Screw
7-4. e last installation step when installing the light fixture is to
install the glass bowl. See “Installing the Glass Bowl” on page 12 for
instructions.
10
42676-01 • 05/13/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
7 • Completing Your Installation With or Without a Bowl Light Fixture (Continued)
Uninstalling the Light Fixture
1. To uninstall the light fixture, first disconnect the plug connectors
Lower Switch
between the black wire and the black/white wire.
Housing
2. Disconnect the plug connectors between the two white wires.
3. Uninstall the nut and washer from the end of the light fixture
inside the lower switch housing.
4. Unscrew the threaded rod of the light fixture from the lower
switch housing.
5. Remove the light fixture from the lower switch housing pulling
disconnected wires through the hole in the center of the lower
switch housing.
.. Note: When removing the wires, pull the thin plug connector
(male) through first, and then pull the other plug connector
(female) through the hole.
6. Install the dummy terminals (included in the sack parts) on the
two disconnected wires in the lower switch housing.
readed Rod
7. Install the switch housing cap and plug button to the lower
switch housing.
Steps 3 – 5
Male Dummy
Terminal
Cap
Female Dummy
Terminal
Plug Button
Step 7
11
42676-01 • 05/13/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
7 • Completing Your Installation With or Without a Bowl Light Fixture (Continued)
Installing the Glass Bowl
Light Bulbs .
(B10
7-5. First install B10 candelabra bulbs (60
Candelabra
Base 60 Watt
Maximum)
Watt Maximum) into the
sockets.
7-6. Attach the extra pull chain (included)
to the fan pull chain using the plastic
breakaway connector. (You may find
the plastic breakaway connector on
the end of the extra chain.)
7-7. read the fan pull chain through the
hole in the metal disk. en, thread
the fan pull chain through the hole in
the center of the glass bowl.
Metal Rod
Metal Disk
Glass Bowl
Cover Plate
Finial
7-8. read the light pull chain through
the hole in the center of the glass
bowl. en, read the light pull chain
throught the hole in the center of the cover plate.
7-9. read the fan pull chain through the grommet hole in the side of
the cover plate.
7-10. Place the cover plate up against the glass bowl. Align the holes in
the cover plate and glass bowl.
7-11. read the light pull chain through the finial and screw the finial
onto the threaded rod end until tight.
Note: In compliance with US federal energy regulations, this
ceiling fan contains a device that restricts the light kit to a
maximum of 190 Watts. Exceeding that limit or the marked
limit on this product may result in fire hazard or improper
operation.
12
42676-01 • 05/13/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
8 • Operating and Cleaning Your Ceiling Fan
8-1. Turn on electrical power to the fan.
8-2. e fan pull chain controls power to the fan. e pull chain has
four settings in sequence: High, Medium, Low, and Off.
• Pull the chain slowly to change settings.
• Release slowly to prevent the chain from recoiling into the
blades.
• e chain uses a breakaway connector that separates if the
chain is jerked. If this happens, simply reinsert the chain into
the connector.
8-3. e light pull chain controls the power to the light fixture. e
chain has two settings: ON and OFF.
In warm weather, use
downward air flow pattern
8-4 . Ceiling fans work best by blowing air downward (counterclockwise
blade rotation) in warm weather to cool the room with a direct
breeze. In winter, having the fan draw air upward (clockwise blade
rotation) will distribute the warmer air trapped at the ceiling
around the room without causing a draft.
8-5. For cleaning finishes, use a soft brush or lint-free cloth to prevent
scratching. A vacuum cleaner brush nozzle can remove heavier
dust. Remove surface smudges or accumulated dirt and dust using
a mild detergent and a slightly dampened cloth. You may use
an artistic agent, but never abrasive cleaning agents as they will
damage the finish.
8-6. Clean wood finish blades with a furniture polishing cloth.
Occasionally, apply a light coat of furniture polish for added
protection and beauty. Clean painted and high-gloss blades in the
same manner as the fan finish.
In cold weather, use upward .
air flow pattern
To Change Airflow Direction
Turn the fan off and let it come to a complete
stop. Slide the reversing switch on the fan to the
opposite position. Restart fan.
Reversing
Switch
13
42676-01 • 05/13/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
9 • Troubleshooting
Problem: Nothing happens; fan does not move.
1. Turn power on, replace fuse, or reset breaker.
2. Loosen canopy, check all connections according to the wiring the
fan section.
3. Check the plug connection in the switch housing.
4. Push motor reversing switch firmly left or right to ensure that the
switch is engaged.
5. Pull the pull chain to ensure it is on.
6. Remove the shipping bumpers.
Problem: Noisy operation.
1. Tighten the blade assembly screws and blade iron armature screws
until snug.
2. Check to see if the blade is cracked. If so, replace all the blades.
Problem: Excessive wobbling.
1. If your fan wobbles when operating, use the enclosed balancing kit
and instructions to balance the fan.
2. Tighten all blade iron screws.
3. Turn power off, support fan very carefully, and check that the
hanger ball is properly seated.
Problem: Lights dim when turned on or do not turn on
1. Check to make sure the wattage and type of light bulbs installed
match the specifications on the light socket.
If you need parts or service assistance, please call
888-830-1326 (In Canada, call 866-268-1936) or
visit us at our Web site at .
Hunter Fan Company
7130 Goodlett Farms Pkwy. #400
Memphis, Tennessee 38016
14
42676-01 • 05/13/09 • Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
|