42027-01 • 12/09/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer’s Choice and Optional Accessories
Understanding Mounting and Installer’s Choice®
Hunter’s patented 3-position mounting system provides you maximum
installation flexibility and ease. You can install your Hunter fan in one
of three ways, depending on ceiling height and your preference: Low
Profile, Standard, or Angle mounting. e steps in this manual include
instructions for all three Installer’s Choice mounting methods.
Low Profile Mounting fits close to the
ceiling, recommended for ceilings less
than 8 feet high
Considering Optional Accessories
Consider using Hunter’s optional accessories, including a wall-mounted
or remote speed control. To install and use the accessories, follow
the instructions included with each product. For quiet and optimum
performance of your Hunter fan, use only Hunter speed controls.
Standard Mounting hangs from
the ceiling by a downrod (included),
recommended for ceilings 8 feet or higher
For ceilings higher than 8 feet, you
can purchase Hunter extension
downrods. All Hunter fans use sturdy
3/4” diameter pipe to assure stability
and wobble-free performance.
3
Angle Mounting recommended for a
vaulted or angled ceiling
42027-01 • 12/09/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
1 • Getting Ready
To install a ceiling fan, be sure you can do the following:
• Locate the ceiling joist or other suitable support in ceiling.
• Drill holes for and install wood screws.
• Identify and connect electrical wires.
• Lift 40 pounds.
If you need help installing the fan, your Hunter fan dealer can direct
you to a licensed installer or electrician.
Gathering the Tools
You will need the following tools for installing the fan:
• Electric drill with 9/64” bit
• Standard screwdriver
• Phillips-head screwdriver
• Wrench or pliers
Checking Your Fan Parts
Carefully unpack your fan to avoid damage to the fan parts. Check
for any shipping damage to the motor or fan blades. If one of the fan
blades was damaged in shipment, return all the blades for replacement.
Installing Multiple Fans?
4
If you are installing more than
one fan, keep the fan blades in
sets, as they were shipped.
If any parts are missing or damaged, contact your Hunter dealer or call
Hunter Parts Department at 888-830-1326.
Preparing the Fan Site
Before you begin installing the fan, follow all the instructions in
the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan
location and attachment to the building structure are essential for
safety, reliable operation, maximum efficiency, and energy savings.
Hunter Fan Company
42027-01 • 12/09/05
Download from Www.Somanuals.com. All Manuals Search And Download.
2 • Installing the Hanger Bracket
2-1. Drill two pilot holes into the wood support structure through the
outermost holes in the outlet box. e pilot holes should be 9/64”
in diameter.
Isolator
Hanger
Bracket
Note: Your fan comes with four pre-installed neoprene noise
isolators.
2-2. read the lead wires from the outlet box down through the hole
in the middle of the hanger bracket.
2-3. Align the slotted holes in the hanger bracket with the pilot holes
you drilled in the wood support structure. For proper alignment
use slotted holes directly across from each other. If you are
installing the fan on an angled ceiling, be sure to orient the hanger
bracket with the large opening towards the ceiling peak.
Note: e isolators should be flush against the ceiling.
2-4. Place a flat washer on each of the two 3” screws and pass the
screws through the slotted holes in the hanger bracket into the
pilot holes you drilled.
5
Tighten the screws into the 9/64” pilot holes; do not use lubricants
on the screws. Do not over tighten.
Steps 2-2 – 2-4
Step 2-3 (Angled Ceiling Only)
Flat Washer
3” Screw
For Angled Ceilings: Be sure to orient
the hanger bracket with the large
opening towards the ceiling peak.
42027-01 • 12/09/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
3 • Assembling and Hanging the Fan
You can assemble your fan for standard or angle mounting as shown
in steps 3-1 – 3-6. For low profile mounting (ceilings less than 8 feet
high), go to steps 3-7 – 3-11 on the next page.
Standard
Mounting
Washer
Label
3-1. Remove the label from the standard mounting washer inside the
canopy. Leave the washer in place. (Note: You will not use the
washer included in the parts sack.)
3-2. To assemble fan to hang down from a flat or angled ceiling, place
the canopy with washer, and canopy trim ring around the adapter
so that they rest on the fan assembly.
3-3. Feed the wires from the fan through the downrod.
3-4. Using the provided allen wrench, loosen the allen head set screw
on the adapter to install the pipe and ball assembly. Note: When
the pipe and ball assembly is fully installed, 2-3 threads on the
pipe will still be visible; this is normal. Securely retighten the set
screw with the allen wrench.
Canopy
Step 3-1
Do not remove the protective wrap
from the silhouette on the motor
housing. You will remove it after the
last step on page 13.
CAUTION: e adapter has a special coating on the threads. Do
not remove this coating; the coating prevents the downrod from
unscrewing. Once assembled, do not remove the downrod.
6
WARNING: Do not carry or lift fan by canopy.
Steps 3-2 – 3-4
3-5. Raise the fan and place the ball into the hanger bracket.
3-6. Align the notch on the ball with the indent in the hanger bracket.
(Rotate the fan until you hear the notch pop into place.)
Downrod
Go to 4 • Wiring the Fan.
WARNING: Fan may fall if not assembled as directed in these
installation instructions.
Canopy
(with Washer)
Canopy
Trim Ring
Adapter
Set Screw
Indent
Steps 3-5 – 3-6
Hunter Fan Company
42027-01 • 12/09/05
Download from Www.Somanuals.com. All Manuals Search And Download.
3 • Assembling and Hanging the Fan (Low Profile Only)
Steps 3-8 – 3-10
You can assemble your fan for standard or angle mounting as shown
in steps 3-1 – 3-6 on the previous page. For low profile mounting
(ceilings less than 8 feet high), see steps 3-7 – 3-11 on this page.
Low Profile Washer
3-7. Locate the washer that comes preassembled in the canopy.
Remove the label and discard the washer and label. Locate the set
screw preassembled in the adapter. Remove and discard the set
screw. (Refer to images on previous page.)
3-8. Place the low profile washer from the parts sack into the canopy.
3-9. Place the canopy trim ring and canopy with washer on top of the
fan assembly.
3-10. Align the screw holes in the washer with the holes in the adapter.
Assemble securely with three #8-32 x 1/2” screws.
3-11. Raise the fan and place the hook on the hanger bracket through
the round hole in the rim of the canopy.
Adapter
#8-32 x 1/2” Screw
Canopy
Trim Ring
WARNING: Fan may fall if not assembled as directed in these
installation instructions.
7
Do not remove the protective wrap
from the silhouette on the motor
housing. You will remove it after the
last step on page 13.
(Not Actual Size)
Hook
Hanger
Bracket
Round
Hole
Low Profile Washer
Step 3-11
Step 3-10 (Detail)
42027-01 • 12/09/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
4 • Wiring the Fan
Step 4-3
All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualified electrician.
Wall switches are not included. Select an acceptable general-use switch in
accordance with national and local electrical codes.
4-1. Disconnect the power by turning off the circuit breakers to the
outlet box and associated wall switch location.
4-2. Decide how you want to set up the fan and light controls. You can
control the fan and/or lights together or separately using one or two
wall switches. Follow Step 4-3 OR Step 4-4, depending on what you
decide.
4-3. If you want to, you can control the fan and light separately using two
wall switches, connect the wires as follows:
• e bare or green ground wire from the ceiling to the green
ground wire from the hanger bracket and the green ground wire
from the fan
• e white wire from the ceiling to the white wire from the fan
• e black wire from the ceiling to the black wire from the fan
• e black/white wire from the fan to the wire for the wall switch
Step 4-4
8
4-4. Alternatively, you can control both fan and light with one switch. To
do so connect the wires as follows:
• e bare or green ground wire from the ceiling to the green
ground wire from the hanger bracket and the green ground wire
from the fan
• e white wire from the ceiling to the white wire from the fan
• e black wire from the ceiling to the black and the black/white
wire from the fan
4-5. To connect the wires, hold the bare metal leads together and place a
wire nut over them, then twist clockwise until tight.
CAUTION: Be sure no bare wire or wire strands are visible after
making connections.
Wire Nut
4-6. Push all wires and wire nuts back into the hanger bracket.
Hunter Fan Company
42027-01 • 12/09/05
Download from Www.Somanuals.com. All Manuals Search And Download.
5 • Installing the Canopy and Canopy Trim Ring
Steps 5-1 – 5-2
Hanger Bracket
5-1. Partially install two canopy screws (about 2 full turns) in the
hanger bracket.
5-2. Raise the canopy over the hanger bracket (For low profile
installations, you will need to remove the canopy from the hook
first). Align partially installed screws with key slots in canopy.
5-3. Twist canopy clockwise to secure.
5-4. Install third canopy screw in round hole on canopy. Securely
tighten all three screws.
Canopy Trim
Ring
Canopy
5-5. Using both hands, push the canopy trim ring up to the top of the
canopy. e canopy trim ring will snap and lock into place.
Should you need to remove the canopy
trim ring, follow these steps:
1. Locate the tab indicators, small
bumps on top of tabs.
2. Press firmly on opposite sides of the
ring towards the canopy. e tabs
will flex out releasing the trim ring
from the canopy
9
Step 5-3
Steps 5-4 – 5-5
Canopy
Screw
42027-01 • 12/09/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
6 • Assembling the Blades
Hunter fans use several styles of fan blade irons (brackets that hold the
blade to the fan).
6-1. Your fan may include blade grommets. If your fan has grommets,
insert them by hand into the holes on the blades.
Step 6-1 (Detail)
6-2. Attach each blade to a blade iron using three blade assembly
screws. If you used grommets, the blades may appear slightly loose
after screws are tightened. is is normal.
6-3. Remove the blade mounting screws and rubber shipping bumpers
from the motor. Note: Some blade mounting screws are installed
in the motor to secure shipping blocks.
6-4. For each blade, insert one blade mounting screw through the
blade iron, and attach lightly to the fan. Insert the second blade
mounting screw, then securely tighten both mounting screws.
Grommet
Blade Assembly
Screws
Steps 6-1 – 6-2
Use with grommet
10
Use without grommet
Blade Mounting
Screw
Step 6-4
Hunter Fan Company
42027-01 • 12/09/05
Download from Www.Somanuals.com. All Manuals Search And Download.
7 • Completing Your Installation With or Without a Light Fixture
7-1. To attach the upper switch housing, partially install two #6-32 x
3/8” housing assembly screws into the switch housing mounting
plate.
7-2. Feed the upper plug connector through the center opening of the
housing.
7-3. Align the keyhole slots in the housing with the housing assembly
screws.
7-4. Turn the housing counterclockwise until the housing assembly
screws are firmly situated in the narrow end of the keyhole slots.
Install the remaining #6-32 x 3/8” screw into the housing. Tighten
all three screws firmly.
CAUTION: Make sure the upper switch housing is securely
attached to the switch housing mounting plate. Failure to properly
attach and tighten all three assembly screws could result in the
switch housing and light fixture falling.
Steps 7-1 – 7-3
Housing
Assembly
Screw
Upper
Switch
Housing
11
Your Hunter fan comes with an integrated light fixture assembly and an
optional switch housing cap and plug button. is feature gives you the
option of installing the fan with OR without the included light fixture.
If you want to install the light fixture, proceed with step 7-5 now.
If you do not want to install the light fixture, you need to uninstall it
now. See “Uninstalling the Light Fixture” on page 14.
WARNING: Use only the light fixture supplied with this fan model.
Step 7-4
42027-01 • 12/09/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
7 • Completing Your Installation With or Without a Light Fixture (Continued)
Note: If you do not want to install the light fixture, see
“Uninstalling the Light Fixture” on page 14.
7-5. To attach the lower switch housing, connect the upper plug
connector from the motor to the lower plug connector in the
lower switch housing assembly.
Lower
Switch
Plug
Housing
Connector
Note: Both plug connectors are polarized and will only fit together
one way. Make sure the connectors are properly aligned before
connecting them. Incorrect connection could cause improper
operation and damage to the product.
7-6. Place the lower switch housing assembly over the upper switch
housing. Align the side screw holes in the upper and lower switch
housings. Attach the lower switch housing to the upper switch
housing with three #6-32 x 3/8” housing assembly screws. You will
need to rotate the blade irons out of the way for each screw.
Screw
Cardboard
Step 7-5
Plug
Connector
Detail
12
Housing
Assembly
Screw
Step 7-6
Hunter Fan Company
42027-01 • 12/09/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Glass Bowl
1. Install three candelabra bulbs (40 Watts maximum each).
2. Attach the extra pull chain (included) to the fan pull chain
using the plastic breakaway connector. (You may find
the plastic breakaway connector on the end of the extra
chain.)
3. read the fan pull chain and light pull chain through the
holes in the metal disk.
4. Place the pull chain cap up against the glass bowl. Align the
holes in the cap and glass bowl.
5. read the fan pull chain and light pull chain through the
appropriate holes in the pull chain cap.
Metal Disk
Silhouette
6. Screw the finial onto the threaded pipe until tight.
7. Remove the protective wrap from the silhouette on the
light fixture before starting the fan.
Steps 1 – 3
Breakaway
Connector
13
Attaching e Pull Chain Pendents
Insert the end of the fan pull chain between
the hooks on the pull chain pendant. Pull
tight to capture the link between the hooks.
Repeat for light pull chain.
Pipe
Glass Bowl
Pull Chain Cap
Finial
Steps 4 – 6
42027-01 • 12/09/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
7 • Completing Your Installation With or Without a Light Fixture (Continued)
Uninstalling the Light Fixture
1. Disconnect the plug connectors.
2. Uninstall the nut and washer from the end of the light fixture inside
the lower switch housing.
Nut and
Washer
Lower
Switch
Housing
3. Remove the light fixture from the lower switch housing pulling
disconnected wires through the hole in the center of the lower
switch housing.
4. Locate the no-light assembly. Place the pipe from the assembly into
the lower switch housing. Install the nut and washer (removed in
step 3) onto the pipe to secure the no-light assembly to the switch
housing.
5. Install the lower switch housing to the upper switch housing with
three screws.
Light Fixture
Step 2
Step 4
Attaching e Pull Chain Pendent
Nut and
Washer
Insert the end of the fan pull chain between
the hooks on the pull chain pendant. Pull tight
to capture the link between the hooks.
14
Lower
Switch
Housing
No-light
Assembly
Step 5
Hunter Fan Company
42027-01 • 12/09/05
Download from Www.Somanuals.com. All Manuals Search And Download.
8 • Operating and Cleaning Your Ceiling Fan
8-1. Turn on electrical power to the fan.
8-2. e fan pull chain controls power to the fan. e pull chain has
four settings in sequence: High, Medium, Low and Off.
• Pull the chain slowly to change settings.
• Release slowly to prevent the chain from recoiling into the
blades.
• e chain uses a breakaway connector that separates if the
chain is jerked. If this happens, simply reinsert the chain into
the connector.
8-3. e light pull chain controls power to the light. e pull chain has
two settings: On and Off.
In warm weather, use
downward air flow pattern
8-4. Ceiling fans work best by blowing air downward (counterclockwise
blade rotation) in warm weather to cool the room with a direct
breeze. In winter, having the fan draw air upward (clockwise blade
rotation) will distribute the warmer air trapped at the ceiling
around the room without causing a draft.
15
8-5. For cleaning finishes, use a soft brush or lint-free cloth to prevent
scratching. A vacuum cleaner brush nozzle can remove heavier
dust. Remove surface smudges or accumulated dirt and dust using
a mild detergent and a slightly dampened cloth. You may use
an artistic agent, but never abrasive cleaning agents as they will
damage the finish.
8-6. Clean wood finish blades with a furniture polishing cloth.
Occasionally, apply a light coat of furniture polish for added
protection and beauty. Clean painted and high-gloss blades in the
same manner as the fan finish.
In cold weather, use upward
air flow pattern
To Change Airflow Direction
Turn the fan off and let it come to a complete
stop. Slide the reversing switch on the fan to the
opposite position. Restart fan.
Reversing
Switch
42027-01 • 12/09/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
9 • Troubleshooting
Problem: Nothing happens; fan does not move.
1. Turn power on, replace fuse, or reset breaker.
2. Loosen canopy, check all connections according to the wiring the
fan section.
3. Check the plug connection in the switch housing.
4. Push motor reversing switch firmly left or right to ensure that the
switch is engaged.
5. Pull the pull chain to ensure it is on.
6. Remove the shipping bumpers.
Problem: Noisy operation.
1. Tighten the blade bracket screws until snug.
2. Tighten the blade screws until snug.
3. Check to see if the blade is cracked. If so, replace all the blades.
4. Change to an approved speed control.
5. Check and tighten the screws in the switch housing mounting
plate and in the upper and lower switch housing.
16
Problem: Excessive wobbling.
1. If your fan wobbles when operating, use the enclosed balancing kit
and instructions to balance the fan.
2. Tighten all blade and/or blade iron screws.
3. Turn power off, support fan very carefully, and check that the
hanger ball is properly seated.
If you need parts or service assistance, please call
888-830-1326 or visit us at our Web site at
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
Hunter Fan Company
42027-01 • 12/09/05
Download from Www.Somanuals.com. All Manuals Search And Download.
|