Hunter Outdoor Light Fixture
Installation Instructions
41370-01 7/28/2005
41370-01 rev 7-28-05.indd
1
7/28/2005, 11:38 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Steps
1. Disconnect power to the ceiling fan by turning off the circuit breakers to both the outlet box
and to its associated wall switch location.
2. Remove the lower switch housing from the fan and remove the cover. (see figure 1)
3. Locate the black wire with a white stripe and the white wire in the lower switch housing. Using
approved wire nut connectors, connect the black wire with a white stripe from the lower switch
housing to the black wire from the light kit, then connect the white wire from the lower switch
housing to the white wire from the light kit. (see figure 2)
4. Align the holes in the lower switch housing with the two partially installed screws in the top of
the light kit. ese screws can be accessed through the two holes in the metal plate which sits
below the light socket. (see figure 2)
5. Attach the light kit to the lower switch housing by securely tightening the two partially installed
screws. Reinstall the lower switch housing. WARNING: Improper installation could cause the
light fixture to fall.
6. Install one 75 Watt max A-19 bulb into the light socket.
7. Align the four holes in the upper louver ring with the four holes in the lower louver ring. When
the holes are properly aligned, the two rings will loosely lock together. (see figure 3)
upper louver
ring
lower switch
partially installed
housing
screw
lower switch
housing
cover
access
holes
lower louver
ring
figure 1
figure 2
figure 3
41370-01 rev 7-28-05.indd
3
7/28/2005, 11:38 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Place the two louver rings over the globe and align the four holes in the rings with the four holes
in the globe. read two screws through to keep the holes aligned. (see figure 4)
9. Align the notch in the upper louver ring with the pull chain switch on the light kit. Align two
screws with two of the four holes in the light kit rim. (see figure 5)
10. Securely install the two threaded screws, followed by the two remaining screws. (see figure 6)
11. Restore power to the ceiling fan.
screws
pull
chain
lower ring
notch
upper ring
screws
screws
figure 5
figure 6
figure 4
globe
41370-01 rev 7-28-05.indd
4
7/28/2005, 11:38 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Light does not come on.
1. Pull light pull chain one or two times to see if light comes on.
2. Make sure the bulb is installed properly and filament is not blown.
3. Make sure breakers or fuses are on.
4. Verify that the light power lead is connected at the ceiling. Refer to your ceiling fan
manual for locating, assembly and wiring.
Globe rattles.
1. Make sure the globe is secure.
2. Tighten all screws.
For questions, contact the Hunter Fan Company Technical Support at
1-888-830-1326 or
41370-01 rev 7-28-05.indd
5
7/28/2005, 11:38 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
is Light Fixture weighs 1.9 lbs.
© 2005 Hunter Fan Company
Printed in China & Taiwan
41370-01 rev 7-28-05.indd
6
7/28/2005, 11:38 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
|