1
530521-2_C
Transducer Switch
Thank You
Thank you for choosing Humminbird®, America's #1 name in fishfinders. Humminbird® has built its reputation by
designing and manufacturing top-quality, thoroughly reliable marine equipment. Genuine Humminbird® accessories
offer the opportunity to upgrade and expand the capabilities of your Humminbird® product.
Your Humminbird® accessory is designed for trouble-free use in even the harshest marine environment.
In the unlikely event that your Humminbird® accessory does require repairs, we offer an exclusive Service Policy - free
of charge during the first year after purchase, and available at a reasonable rate after the one-year period. For
complete details, see the Warranty section included in this manual.
Installation Overview
Following are instructions for the installation of this accessory. Before you start installation, we encourage you to read
these instructions carefully in order to get the full benefit from your Humminbird® accessory.
If you find that any items are missing from your installation kit, call our Customer Resource Center at 1-800-633-1468
The Transducer Switch comes with all the necessary hardware to allow you to connect your control head to two
transducers. The transducers may be the same type of transducer with different mounting locations, or you can
maximize your unit’s performance by using two different transducers. The switch is intended for installation on the
console, and will work well on almost any boat.
Transducer Switch With Cover
In addition to the hardware supplied with your Transducer Switch, you will need a hand drill with various size bits, a
Phillips screwdriver, and an adjustable wrench.
TRANSDUCER SELECTOR
Before installing the Transducer Switch, gather all the parts you will need, and make sure that the planned location of
the Transducer Switch will allow you to connect the two transducers to your control head.
A
B
Installation
Perform the procedures in the following sections to install the Transducer Switch on your boat.
1.
Locating the Transducer Switch Mounting Position
To determine where to mount the Transducer Switch, make sure that it will be positioned near your control head on
the console of the boat, within reach of the cables for both transducers.
After you have determined the best mounting location for your Transducer Switch, proceed with the following
instructions.
Switch Assembly
2.
Attaching the Transducer Switch
Boat Console
Switch
1. Remove the switch plate from the switch assembly.
2. Using the switch plate as a template, mark the location of the hole with a pencil or punch.
3. Drill a 1/2” mounting hole at the desired location.
T
R
A
N
S
D
U
C
E
R
S
E
L
E
A
C
T
O
R
B
Switch Cover
Rubber Boot
4. Test the fit of the Transducer Switch in the mounting location.
5. Remove the paper from the back of the switch cover to expose the adhesive backing and press the switch plate
onto the mounting location.
© 2008 Humminbird®, Eufaula AL, USA.
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
530521-2_C
Transducer Switch
Maintenance
Humminbird® Service Policy
If your boat remains in the water for long periods of time, algae and other
marine growth can reduce the effectiveness of the transducer. Periodically
clean the face of the transducer with hot water.
Even though you'll probably never need to take advantage of our incredible
service policy, it's good to know that we back our products this confidently.
We do it because you deserve the best. We will make every effort to repair
your unit within three business days from the receipt of your unit at our
factory. This does not include shipping time to and from our factory. Units
received on Friday are typically shipped by the following Wednesday, units
received Monday are typically shipped by Thursday, etc.
If your boat remains out of the water for a long period of time, it may take
some time to wet the transducer after it is returned to the water. Small air
bubbles can cling to the surface of the transducer and interfere with proper
operation. These bubbles will dissipate with time, or you may wipe the face of
the transducer with your fingers after the transducer is in the water.
All repair work is performed by factory-trained technicians to meet exacting
factory specifications. Factory-serviced units go through the same rigorous
testing and quality control inspections as new production units.
1-Year Limited Warranty
After the original warranty period, a standard flat rate service charge will
be assessed for each repair (physical damage and missing parts are not
included). Any repairs made after the original warranty will be warranted
for an additional 90 days after service has been performed by our factory
technicians. You can contact our Customer Resource Center or visit our
web site to verify the flat rate repair fee for your product (visit the Product
Support section):
We warrant the original retail purchaser that products made by Humminbird®
have been manufactured free from defects in materials and workmanship.
This warranty is effective for one year from the date of original retail
purchase. Humminbird® products found to be defective and covered by this
warranty will be replaced or repaired free of charge at Humminbird® option
and returned to the customer freight prepaid. Humminbird® sole responsibility
under this warranty is limited to the repair or replacement of a product that
has been deemed defective by Humminbird®. Humminbird® is not responsible
for charges connected with the removal of such product or reinstallation of
replaced or repaired parts.
We reserve the right to deem any product unserviceable when replacement
parts are no longer available or impossible to obtain. This Service Policy is
valid in the United States only. This applies only to Humminbird® products
returned to our factory in Eufaula, Alabama. This Service Policy is subject to
change without notice.
This warranty does not apply to a product that has been:
• Improperly installed;
• Used in an installation other than that recommended in the product
installation and operation instructions;
DOMESTIC (USA) CUSTOMERS:
• Damaged or has failed because of an accident or abnormal operation;
• Repaired or modified by entities other than Humminbird®.
PLEASE DO NOT RETURN THIS PRODUCT TO STORE FOR SERVICE
For all technical issues please call 1-800-633-1468
Please reference product serial number and
Please retain your original receipt as a proof of the purchase date. This will be
required for in-warranty service.
model number when contacting Humminbird®.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD® AND WILL BE
THE CUSTOMER'S EXCLUSIVE REMEDY, EXCEPT FOR ANY APPLICABLE
IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE HEREBY LIMITED IN
DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. IN NO
EVENT WILL HUMMINBIRD® BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY RELATING TO THE PRODUCTS.
Some states do not allow limitations on an implied warranty, or the exclusion
of incidental or consequential damages, so the above exclusions may not
apply to you. You may also have other rights, which vary from state to state.
© 2008 Humminbird®, Eufaula AL, USA.
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
530521-2_C
Transducer Switch
Returning Your Unit for Service
Contact Humminbird®
Before sending your unit in for repair, please contact the factory, either by
phone or by email, to obtain a Repair Authorization Number for your unit.
Contact the Humminbird® Customer Resource Center
in any of the following ways:
NOTE: Please do not return your Humminbird® to the store for service.
By Telephone
(Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time):
Please have your product model name and serial number available before
calling the factory. If you contact the factory by e-mail, please include your
product model name and serial number in the e-mail, and use Request for
Repair Authorization Number for your e-mail subject header. You should
include your Repair Authorization Number in all subsequent communications
about your unit.
1-800-633-1468
By e-mail
(typically we respond to your e-mail within three business days):
For IN-WARRANTY service, complete the following steps:
For direct shipping, our address is:
• Obtain a Repair Authorization Number from the Humminbird® Customer
Resource Center.
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
• Tag product with your name, street address, phone number and your
assigned Repair Authorization Number.
• Include a brief written description of the problem.
• Include a copy of your receipt (to show proof and date of purchase).
• Return product freight prepaid to Humminbird®, using an insured carrier
with delivery confirmation.
For OUT-OF-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from the Humminbird® Customer
Resource Center.
• Include payment in the form of credit card number and expiration date,
money order or personal check. Please do not send cash.
• Tag product with your name, street address, phone number and your
assigned Repair Authorization Number.
• Include a brief written description of the problem.
• Return product freight prepaid to Humminbird®, using an insured carrier
with delivery confirmation.
© 2008 Humminbird®, Eufaula AL, USA.
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|