12/01
P/N 211488E
1
© COPYRIGHT 2001 by HUFFY SPORTS
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (continued)
Item #46 (1)
Item #39 (2)
Item #43 (2)
Item #40 (5)
Item #41 (3)
Item #44 (2)
Item #49 (1)
Item #50 (1)
Item #53 (1)
Item #52 (1)
Item #58 (9)
Item #61 (1)
Item #59 (2)
Item #68 (4)*
Item #69 (2)
3
12/01 P/N 211488E
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST - See Hardware Identifier
Item Qty. Part No. Description
Item Qty. Part No. Description
1
2
3
4
5
6
7
8
9
1
1
4
1
1
1
1
1
1
3*
2
1
206615 Tank, (Black)
200628 Wheel Axle, 11-3/4 Long
226401 Wheel, 4 “ (Black)
900107 Top Pole Section
900106 Middle Pole Section
900105 Bottom Pole Section
202820 Rod, 3/8 O.D. x 4-3/4 Long
206934 Eyebolt, 3/8-16 x 2 1/2 Long
206949 Pivot Bracket, Upper
203063 Nylon Insert Lock Nut, 3/8-16
906206 Strut, 1” O.D. x 43 Long
202662 Bolt, Hex Head, 5/16-18 x 4-1/2 Long
35
36
2
2
900103 Bracket, Backboard Support
206360 Bolt, Hex Head, 3/8-16 x 2.625 Long
200874 Spacer, Steel .402 I.D. x .50 O.D. x 1.5 Long
201124 Nut, 3/8-16
201642 Spacer .530 I.D. x .625 Long
206340 Nut 1/2-13
201640 Bolt 1/2-13 x 7-1/4 Long
900183 Lower Elevator Tubes - Long
201681 Spacer .530 I.D. x.63 O.D. x .875 Long
206304 Bolt 1/2-13 x 6-5/16 Long
900184 Upper Elevator Tubes - Short
200516 Vinyl Bolt Cover, 5/16
207103 Cap, Pole Top
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
2
3
2
5
3
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
9
2
1
1
1
2
1
1
1
1
4*
2
10
11
12
13 12* 203218 Washer, Flat, 3/8 I.D.
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
2
1
2
14
2
1
1
2
1
1
1
2
1
1
1
1
2
203220 Nylon Insert Lock Nut, 5/16-18
200629 Anchor, T-Strap
203798 Bolt, Hex Flange, 5/16-18 x 1-1/2 Long
203100 Nut, Hex Flange, 5/16-18
203103 Carriage Bolt, 5/16-18 x 2 Long
900223 Wheel Bracket
204838 Spring, Silver
203112 Bolt, 5/16-18 x 6-1/2 Long
200830 Bolt, 3/8-16 x 7-1/2 Long
900006 Adjustment Tube
200214 Locking Pin
200215 Cross Pin
200211 Left Handle
200210 Right Handle
200257 Spring
200212 Trigger
204804 Screw, Phillips Head, 3/4 Long
202862 Spacer .563 I.D. x 1.19 Long
908008 Adjustment Rod
202739 Bolt 5/16-18 x 1-3/4 Long
203124 Stake, Tie Down
203617 Plug Cap
211261 Label, Height Adjustment and Moving
204281 Net
204872 Label, Height Indicator
200627 Wheel Carriage
205528 Bolt, Hex Flange, 5/16-18 x 1 Long
201651 Spacer, Wheel Axle
206948 Pivot Bracket, Lower
206252 Bolt, Hex Head, 3/8-16 x 1 Long
206956 Disc, 5" O.D. x 13/32 I.D., Plastic
906606 Handle Bar
206940 Axle
206938 Push Cap
203330 Bolt, Hex Head, 3/8-16 x 4-1/2 Long
204849 Handle, Front, Plastic
204849 Handle, Back, Plastic
206990 Reinforcement Bracket
203217 Carriage Bolt, 5/16-18 x 1-1/2 Long
31 12* 200120 Clip, Net Holder, (Red)
200121 Clip, Net Holder, (Black)
32
33
34
1
1
2
Rim
200209 Bracket, Pole Mount
203053 Bolt, Carriage, 5/16-18 x4 Long
WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC
BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY
HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD
COULD RESULT IN SUDDEN BREAKAGE. IF BACKBOARD IS DAMAGED
IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLL-FREE
NUMBER FOR FREE REPLACEMENT:
WARRANTY CARD:
Please remember to complete your product
registration form either
on-line at: www.huffysports.com/warrantycard
or mail-in the enclosed postcard.
P/N 211488E 12/01
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCTIONS
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF
THIS OWNERS MANUAL
17. Attach elevator bracket (33) to middle pole section (5) using bolts (34),
reinforcement bracket (29), and nuts (17) as shown.
18. Attach backboard support brackets (35) to the backboard frame using
bolts (36), spacers (37), and nuts (38) as shown.
19. Attach lower elevator tubes (42) to backboard support brackets (35) using
spacers (39), bolt (41), and nut (40) as shown. NOTE: Rim mounting
nuts and bolts supplied with rim hardware. NOTE: DO NOT use washers
here on spring return style rims.
20. Attach upper elevator tubes (45) to backboard support brackets (35) using
spacers (43), bolt (44), and nut (40) as shown.
21. A.Attach upper and lower elevator tubes (45, 42) to upper pole
section (4) using bolts (44, 41) and nuts (40) as shown. Attach pole
cap (48) as shown.
1. Remove all contents from underside of tank. Keep tank (1) bottom side
up. Install wheel axle (2) through wheel carriage (67) and install wheels
(3) onto wheel axle (2) with spacers (69) as shown. Secure wheel bracket
as shown, a deep socket is recommended.
IMPORTANT! DO NOT OVER TIGHTEN.
2. Correctly identify each pole section and mark indicated distance from ends
with tape as shown.
B.Attach counterbalance spring (48) to upper elevator tubes (45) with bolt
(49) and nut (14) in location shown. Stretch spring to lower elevator
tubes (42) and attach with hardware (50, 10) as shown.
NOTE: Slide counterbalance spring against elevator tubes.
22. Insert locking pin (52) into bracket on adjustment tube (51). Insert cross
pin (53) through hole in bracket and locking pin (52) as shown in
figure A. Fit left handle (54) onto adjustment tube (51) so the bottom of
adjustment tube (51) sits on the two small ribs of the handle as shown in
figure B.
23. Insert spring (56) into back of locking pin (52) as shown. Spring (56)
should rest between two small ribs at the back of the plastic handle as
shown in Figure C. Insert top of trigger (57) into bracket on the
adjustment tube (51) as shown. The plastic post of the handle pieces
should go through the hole in bottom of trigger (57) and hold it into place
as shown.
24. Finish handle assembly by attaching right handle (55) using screws (58)
as shown.
25. Attach adjustment tube (51) to lower elevator tubes (42) using bolt (41),
spacers (59), and nut (40) as shown.
26. Insert lower adjustment rod (60) into bottom of adjustment tube (51), pull
trigger to allow lower adjustment rod (60) to move about mid-way into
adjustment tube (51), release trigger so the lower adjustment rod (60)
locks into position midway inside adjustment tube (51). Attach lower
adjustment rod (60) to elevator bracket (33) using bolt (61) and nut (14) as
shown.
3. Align pole top and middle pole sections as shown using alignment mark
and hole.
IMPORTANT! Holes in top (4) and middle pole (5) sections MUST
align to correctly position elevator system toward playing surface.
Bounce pole top (4) and middle section (5) together as shown until they
no longer move toward taped reference mark. NOTE: Pole sections
should have a 3-1/2" (9 cm) minimum overlap.
4. IMPORTANT! Holes in top (4) and bottom pole (6) sections MUST
align to correctly position elevator system toward playing surface.
Add bottom pole section (6) to assembly as shown using alignment mark
and hole, and bounce until completely tight. Once assembled, pole
sections CAN NOT be separated! NOTE: Pole sections should have a
3-1/2" (9 cm) minimum overlap.
5. Install rod (7) through holes in bottom pole section (6) and eyebolt (8).
6. Insert pole assembly into tank assembly as shown. Secure pole assembly
with upper pivot bracket (9) and lock nut (10).
7. Secure base struts (11) to pole using bolt (12), washers (13), and nut (14),
as shown. Place vinyl bolt cover (46) over exposed bolt threads. Rotate
the non-secured ends of base struts (11) as shown.
8. Secure base struts (11) to base using bolt (16), washers (13), and
nut (17).
WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS
PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT
IN BODILY INJURY.
9. Insert carriage bolts (18) into middle set of holes on wheel bracket (19) as
shown.
10. Attach lower pivot bracket (20) to wheel bracket (19) using bolt (21),
washers (13), disc (22), and nut (10) as shown.
WARNING: DO NOT LEAVE ASSEMBLED UNIT UNATTENDED WHEN
EMPTY, MAY TIP OVER.
27. Roll the completed assembly to the desired playing area. Insert the
T-strap (15) through the slot on the back of the base as shown. Secure
the unit to ground by twisting the tie down stake (62) into the ground and
hooking the T-strap (15) onto the tie down stake (62). Fill tank with 33
gallons of water.
11. Attach handle bar (23) to wheel bracket assembly using nuts (17) as
shown.
12. Install wheels (3) onto axle (24) and wheel bracket assembly with push
caps (25) as shown.
13. Attach wheel bracket assembly to base assembly using bolt (26), washers
(13), and nut (10) as shown.
14. NOTE: Two people recommended for this step. Carefully reposition
entire assembly to upright position.
IMPORTANT! Add two gallons (7.6 Liters) of non-toxic antifreeze in
sub-freezing climates.
WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN
EMPTY, MAY TIP OVER.
Attach front of plastic handle (27) to back of plastic handle (28) around
handle bar (23) using self-tapping screws (58) as shown.
IMPORTANT! Front of plastic handle (27) should face outward, away
from pole assembly.
28. Apply the height adjustment and moving label (64) to the front of the pole
as shown.
29. Install net (65).
15. Insert bolts (30) through plastic handle assembly, handle bar (23) and
attach nuts (17) as shown. Tighten completely.
16. Install net clips (21).
IMPORTANT! Make sure net is held by all three hooks on the net
clip.
A.Slide net into outer hook as shown.
B.Slide net into second outer hook creating a loop as shown. Push loop
to back of clip.
C.Pull loop up and through back of clip, snapping over the middle hook.
D.Pull net down to make sure it is held securely by all three hooks.
NOTE: If net releases during normal play, net was improperly installed.
Please review instructions to install net properly.
The Quick Clip™ rapid release net system lets the net pull away from the
rim. This reduces the risk of player injury or property damage. However,
improper installation or a ball making contact at an odd angle may
disengage the net clip from the goal rim. Usually, the clip is reinstalled
with little or no problem. We hope that you agree this inconvenience is
minor when compared to the safety of the players. Quick Clip: US Patent
No. 5,792,010/5,795,253
The two outer hooks on net clip must face towards inside of goal rim.
Insert larger hole in net clip onto rim stud, push down on net clip, then
slide net clip right, locking or snapping securely into position (clips must
"snap" into place to insure a secure fit).
30. Lock elevator system into highest position (so the backboard is as high as
it will go). Apply 10 ft. height indication sticker (66) to adjustment tube
(51) directly below arrow on handle as shown. Move elevator system to
the next position and apply the 91/2 ft. sticker. Repeat until all height
settings have been labeled. (8-10ft.)
NOTE: Net clips should not slide with ease. It is very important that the
net clips are in the locked position before going on to next step.
31. Pull trigger (57). Move elevator system up or down to desired height,
release trigger (57) to lock system into one of the five height settings.
WARNING: USE OF THIS PRODUCT WITHOUT PROPER
INSTALLATION OF NET CLIPS, OR WHEN ALL NET CLIPS ARE NOT
PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW
DIRECTIONS CAREFULLY.
WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT.
5
12/01 P/N 211488E
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL
1
1.
21
13
38
67
69
3
69
3
2
P/N 211488E 12/01
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
4
5
5
5
4
6
4
4.
5.
7
6
6
6
5
8
5
7
12/01 P/N 211488E
Download from Www.Somanuals.com. All Manuals Search And Download.
14
6.
7.
46
11
WARNING
SEE TEXT PAGE
13
6
13
6
12
1
6
11
1
9
11
10
8.
9.
18
19
11
16
13
1
13
17
10.
11.
21
20
19
10
13
22
23
13
17
P/N 211488E 12/01
8
Download from Www.Somanuals.com. All Manuals Search And Download.
12.
13.
10
25
13
3
24
3
25
13
26
14.
15.
17
30
28
27
58
23
30
17
58
NET CLIP INSTALLATION
OUTSIDE VIEW
16.
Note
(See Text Page)
32
OUTER HOOKS
WARNING
SEE TEXT PAGE
31
9
12/01 P/N 211488E
Download from Www.Somanuals.com. All Manuals Search And Download.
17.
34
33
29
17
18.
35
38
37
35
35
37
36
P/N 211488E 12/01
10
Download from Www.Somanuals.com. All Manuals Search And Download.
19.
40
35
39
39
41
42
42
Refer To
Instructions
Included With Rim
Hardware For Rim
Assembly.
68
68
20.
40
43
35
45
43
44
45
11
12/01 P/N 211488E
Download from Www.Somanuals.com. All Manuals Search And Download.
21.
45
40
A.
40
42
47
45
44
42
41
14
B.
49
45
48
50
42
10
P/N 211488E 12/01
12
Download from Www.Somanuals.com. All Manuals Search And Download.
22.
Fig. A
52
IMPORTANT!
53
SEE TEXT PAGE
51
53
52
51
54
Fig. B
51
54
13
12/01 P/N 211488E
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT!
23.
SEE TEXT PAGE
53
52
56
51
Fig. C
57
54
52
53
56
54
P/N 211488E 12/01
14
Download from Www.Somanuals.com. All Manuals Search And Download.
24.
25.
58
58
55
41
51
59
58
42
58
45
59
54
58
40
26.
51
33
61
60
14
15
12/01 P/N 211488E
Download from Www.Somanuals.com. All Manuals Search And Download.
27.
28.
WARNING
SEE TEXT PAGE
NOTE:
Peel protective film from
surface of acrylic
backboard prior to use.
63
15
64
10 ft.
(3.05 m)
IMPORTANT!
SEE TEXT PAGE
62
NET INSTALLATION
29.
FRONT VIEW
BACK VIEW
IMPORTANT!
(See Text Page)
65
A
65
C
D
Note
32
32
(See Text Page)
B
P/N 211488E 12/01
16
Download from Www.Somanuals.com. All Manuals Search And Download.
HEIGHT ADJUSTMENT STICKERS
30.
IMPORTANT!
SEE TEXT PAGE
66
51
HEIGHT ADJUSTMENT
31.
WARNING
SEE TEXT PAGE
57
17
12/01 P/N 211488E
Download from Www.Somanuals.com. All Manuals Search And Download.
|