REQUIRED TOOLS
AND MATERIALS:
Portable System
Owners Manual
• 2 People
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
• Tape Measure
• Wood Board
(scrap)
• Sawhorse or
Support Table
• Safety Glasses
• Step Ladder - 8ft.
(2.4 m)
• #2 or #3 Phillips
Screwdriver
• (2 each) Wrenches and/or Socket
Wrenches and Sockets (Deep-
Well Sockets are Recommended).
• Extension is Recommended.
1/2" 9/16" 3/4"
AND/OR
1/2" 9/16" 3/4"
• Garden Hose or Sand
Write Model Number
WARNING!
From Box Here:
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
PROPERTY.
OPTIONAL TOOLS
AND MATERIALS:
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-632 7921
• Large and Small Adjustable
Wrenches
Internet Address: http://www.huffysports.com
1
11/05
ID# M731321
© COPYRIGHT 2005 by SPALDING
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully.
Check entire box and inside all packing material for parts and/or additional instruction material. Before
beginning assembly, read the instructions and identify parts using the hardware identifier and parts list in
this document. Proper and complete assembly, use, and supervision are essential for proper operation and
to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not
installed, maintained, and operated properly.
• If using a ladder during assembly, use extreme caution.
• Two (2) people are recommended for this operation.
• Check base regularly for leakage. Slow leaks could cause system to tip over unexpectedly.
• Seat the pole sections properly (if applicable). Failure to do so could allow the pole sections
to separate during play and/or transport of the system.
• Climate, corrosion, or misuse could result in system failure.
• Minimum operational height is 6' 6" (1.98 m) to the bottom of backboard.
• This equipment is intended for home recreational use only and NOT excessive competitive
play.
• Read and understand the warning label affixed to pole.
• The life of your basketball pole depends on many conditions. The climate, placement of the
pole, location of the pole, exposure to corrosives such as pesticides, herbicides, or salts are
all important.
• If technical assistance is required, contact Huffy Sports.
• Adult supervision is recommended when adjusting height.
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this system.
25
3
11/05
ID# M731321
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections,
hardware and additional parts are packed inside.
NOTICE TO ASSEMBLERS
ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled
and ballasted with sand or water according to the instructions. Failure to follow instructions
could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
WARRANTY CARD:
Please remember to complete your product registration form either
on-line at:
mail-in the enclosed postcard.
WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC
BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY
HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD
COULD RESULT IN SUDDEN BREAKAGE. IF BACKBOARD IS DAMAGED
IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLL-FREE
NUMBER:
4
ID# M731321
11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Get to know the basic parts of your basketball system...
FRONT VIEW
BACKBOARD
RIM
ELEVATOR ADJUSTMENT
POLE
SUPPORT STRUT
BASE
5
11/05
ID# M731321
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST - See Hardware Identifier
Item Qty. Part No. Description
1
2
3
4
5
6
7
8
1
1
2
1
1
1
1
1
206657 Tank, (Black)
200628 Wheel Axle
226401 Wheel, 4“ (Black)
90021701 Top Pole Section
904840 Middle Pole Section
900136 Bottom Pole Section
202820 Rod, 3/8 O.D. x 4-3/4 Long
202822 Eyebolt, 3/8-16 x 2-1/2 Long
9
7* 203063 Nylon Insert Lock Nut, 3/8-16
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
2
1
6
2
1
6
8
2
5
1
1
5
5
1
2
1
1
1
2
2
1
1
1
1
1
4
1
1
1
2
1
2
4
1
2
1
1
1
1
1
1
2
1
906206 Tank Strut
201625 Bolt,Yellow Dichromate, 5/16-18 X 3.60" Long
203218 Washer, Flat, 3/8 I.D.
203099 Nylon Insert Lock Nut, 5/16-18
206219 Cap, Pole Top 3”
205528 Bolt, Hex Flange, 5/16-18 x 1 Long
203100 Nut, Hex Flange, 5/16-18
201651 Spacer .500 I.D. x .25 Long
204804 Screw, Phillips Head, 3/4 Long
200627 Wheel Bracket
Rim
206340 Nut 1/2-13
206304 Bolt 1/2-13 x 6-5/16 Long
202739 Bolt 5/16-18 x 1.75 Long
203617 Plug Cap
211262 Label, Height Adjustment and Moving
Net
200209 Pole Mount Bracket
203231 Bolt, Carriage, 5/16-18 x 3.5 Long
90096401 Backboard Bracket
203472 Spring, Black, Slam Jam
200318 Bracket, Reinforcement, Slam Jam
900033 Bracket Slam Jam
200212 Trigger
206990 Reinforcement Bracket
204961 Bolt, Hex 3/8-16 x .625 Long
203796 T-Bolt, 3/8-16 x 5” Long
204872 Labels Height Indicator
203470 Washer Flat, Slam Jam
203678 Bolt, Hex, 3/8-16 x 6.5" Long
203795 Nut, Special, Slam Jam
902537 Lower Elevator Tubes
201642 Spacer .530 I.D. x.5 O.D. x .63 Long
204838 Spring, Elevator
900184 Upper Elevator Tubes
200215 Cross Pin
200214 Locking Pin
200211 Left Handle
200210 Right Handle
900006 Adjustment Tube - Upper
200257 Spring
202862 Spacer .563 I.D. x 1.19 Long
908109 Adjustment Rod - Lower
NOTE: Hardware kit is designed for more than one style of basketball system. Not all hardware
will be used.
* You may have extra parts with this model.
6
ID# M731321
11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (BOLTS AND SCREWS)
Item #18 (5)
Item #8 (1)
Item #28 (2)
Item #23 (1)
Item #15 (6)
Item #35 (4)
Item #11 (1)
Item #39 (2)
Item #22 (5)
HARDWARE IDENTIFIER (NUTS AND WASHERS)
Item #13 (2)
Item #16 (8)
Item #12 (6)
Item #38 (1)
Item #9 (7*)
Item #21 (5)
7
11/05
ID# M731321
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (STEEL SPACERS)
Item #45 (1)
Item #46 (1)
Item #42 (4)
HARDWARE IDENTIFIER (PLASTIC SPACERS, CAPS, CLIPS AND OTHER)
Item #7 (1)
Item #51 (2)
Item #36 (1)
Item #40 (1)
Item #17 (2)
Item #32 (1)
Item #31 (1)
Item #30 (1)
8
ID# M731321
11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION A: ASSEMBLE THE BASE
ITEMS REQUIRED FOR THIS SECTION
(2) 1/2” and (2) 9/16" Wrenches
This is what your system will
look like when you’ve
finished this section.
AND/OR
(2) Socket Wrenches and Sockets
1/2”
9/16”
Correctly identify each pole section. Poles have an identification sticker that will be used as a
reference point in the next step.
1.
Identification Sticker
4
TOP
5
MIDDLE
Identification Sticker
6
BOTTOM
9
11/05
ID# M731321
Download from Www.Somanuals.com. All Manuals Search And Download.
While maintaining alignment, bounce pole top (4) and middle section (5) together as shown until
they no longer move toward identification sticker. Upright assembly.
2.
CAUTION!
THE IDENTIFICATION STICKER IS
LOCATED 5" FROM THE END OF
THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 3-1/2"
MINIMUM OVERLAP, LEAVING 1-1/2"
BETWEEN THE OVERLAPPING
POLE AND THE IDENTIFICATION
STICKER.
IMPORTANT!
Align dimple of top pole section (4)
into trough of middle pole section (5)
as shown.
m i d d l e p o l e
ID
STICKER
5
5"
m i d d l e p o l e
1-1/2"
DIMPLE
4
WOOD SCRAP
(NOT SUPPLIED)
HOLE
10
ID# M731321
11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
While maintaining alignment, bounce assembly and bottom pole section (6) together as shown
until they no longer move toward identification sticker.
3.
CAUTION!
THE IDENTIFICATION STICKER IS
LOCATED 5" FROM THE END OF
THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 3-1/2"
MINIMUM OVERLAP, LEAVING 1-1/2"
BETWEEN THE OVERLAPPING
POLE AND THE IDENTIFICATION
STICKER.
IMPORTANT!
Align dimple of middle pole section (5)
into trough of bottom pole section (6)
as shown.
4
5
1-1/2"
Bottom pole
5"
ID
STICKER
Bottom pole
DIMPLE
6
HOLE
WOOD SCRAP
(NOT SUPPLIED)
11
11/05
ID# M731321
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Install rod (7) through holes in bottom pole section (6)
and eyebolt (8).
4.
7
8
Install wheel axle (2) through wheel carriage (19) and install wheels (3) onto wheel axle (2) with
spacers (17) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (6)
5.
section to tank and wheel carriage as shown. A deep socket is recommended.
IMPORTANT!
IMPORTANT!
DO NOT OVER
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT
IN SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
TIGHTEN
THE SPACER (17) WILL
FIT LOOSELY UNTIL
SECURED INTO THE
CAVITY OF THE BASE.
6
1
7
8
IMPORTANT!
The Warning Label
should be facing
towards the front.
9
19
2
17
17
3
3
12
ID# M731321
11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure flat end of tank struts (10) to pole using bolt (11), washers (12), and nut (13), as
shown. Rotate the non-secured angled ends of the struts (10) as shown.
6.
WARNING!
TIGHTEN BOLT (11) IN LOCK NUT (13) UNTIL FLUSH
(EVEN) WITH LOCK NUT’S OUTER EDGE.
12
12
6
13
6
11
10
10
1
10
7. Secure tank struts (10) to the base using
bolt (15), washers (12), and nut (16).
10
15
12
1
10
15
12
12
16
12
16
13
11/05
ID# M731321
Download from Www.Somanuals.com. All Manuals Search And Download.
Install pole mount bracket (27) and reinforcement bracket (34) with carriage bolts (28)
in lower pole mounting holes as shown. Tighten flange nuts (16) completely.
8.
5
28
16
34
28
27
5
27
34
16
FRONT
SIDE
6
14
ID# M731321
11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION B: ATTACH THE BACKBOARD
ITEMS REQUIRED FOR THIS SECTION
This is what your system will look like
when you’ve finished this section.
(2) 1/2" AND (2) 9/16" AND (2) 3/4" Wrenches
AND/OR
(2) Socket Wrenches and Sockets
1/2” 9/16” 3/4”
15
11/05
ID# M731321
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
Assemble backboard brackets (29) using bolts (35), and nuts (9) as shown.
IMPORTANT!
9
Test fit bolts into holes of brackets
and carefully rock them in a
circular motion to ream out paint
from holes if necessary.
35
29
9
35
NOTE ORIENTATION
29
35
35
29
2.
Identify elevator tubes (41 and 44).
44
Upper Elevator tube
Toward Pole
Toward Board
Lower Elevator tube
41
16
ID# M731321
11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Attach lower elevator tubes (41) to backboard brackets (29) using
spacers (42) bolt (22) and nut (21) as shown. Insert “T” bolt (36) through
Slam Jam bracket (32) as shown. Secure Slam Jam bracket (32) and
backboard bracket (29) assemblies to backboard. Use bolt (15) and nut
(16) as shown.
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
16
16
21
29
42
42
41
22
41
36
32
15
IMPORTANT!
15
32
Test fit bolts into holes of brackets
and carefully rock them in a
circular motion to ream out paint
from holes if necessary.
17
11/05
ID# M731321
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach upper elevator tubes (44) to backboard support brackets (29) using spacers (42), bolt (22),
and nut (21) as shown.
4.
21
42
29
44
42
22
44
18
ID# M731321
11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Support pole on sawhorse. Attach upper and lower elevator tubes (41 and 44) to upper pole
section (4) using bolts (22) and nuts (21) as shown. Attach pole cap (14) as shown.
5.
21
21
44
41
4
14
44
41
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
22
22
19
11/05
ID# M731321
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert locking pin (46) into bracket on adjustment tube (49). Insert cross pin (45) through hole in
bracket and locking pin (46) as shown in figure A. Fit left handle (47) onto adjustment tube (49)
so the bottom of adjustment tube (49) sits on the two small ribs of the handle as shown in
figure B.
6.
Fig. A
45
49
45
46
49
47
Fig. B
49
47
20
ID# M731321
11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert spring (50) into back of locking pin (46) as shown. Spring (50) should rest between two
small ribs at the back of the plastic handle as shown in Figure C. Insert top of trigger (33) into
bracket on the adjustment tube (49) as shown. The plastic post of the handle pieces should go
through the hole in bottom of trigger (33) and hold it into place as shown.
7.
49
46
50
47
33
Fig. C
50
46
47
21
11/05
ID# M731321
Download from Www.Somanuals.com. All Manuals Search And Download.
Finish handle assembly by attaching right handle
(48) using screws (18) as shown.
8.
18
18
48
18
47
18
18
9.
Attach adjustment tube (49) to lower elevator tubes (41) using bolt (22) spacers (51) and
nut (21) as shown.
22
49
51
41
51
21
22
ID# M731321
11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert lower adjustment rod (52) into bottom of adjustment tube (49), pull trigger to allow
lower adjustment rod to move about mid-way into adjustment tube (49), release the trigger
so the lower adjustment rod (52) locks into position midway inside the adjustment tube (49).
Attach the lower adjustment rod (52) to elevator bracket (27) using bolt (23) and nut (13) as
shown.
10.
WARNING!
WARNING!
DO NOT LEAVE
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
ASSEMBLY
FAILURE TO FOLLOW THIS
UNATTENDED WHEN
WARNING COULD RESULT IN
EMPTY; IT MAY TIP
SERIOUS INJURY AND/OR
OVER.
PROPERTY DAMAGE.
49
52
27
52
23
13
23
11/05
ID# M731321
Download from Www.Somanuals.com. All Manuals Search And Download.
11.
Install Slam Jam Rim to Backboard
A. Fit rim (20) securely into bracket (32) as shown. Allow T-bolt (36) to slip through center hole in rim
(20).
B. Install reinforcement bracket (31) onto T bolt (36) as shown.
C. Install spring (30) onto T bolt (36) as shown.
D. Install special nut (40) and washer (38) onto T bolt (36).
E. Tighten nut (40) until flush with end of T bolt (36).
A
B
20
31
36
36
32
C
D
40
30
38
36
36
E
38
40
24
ID# M731321
11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Support system on sawhorse. Extend system to highest position before assembly of spring.
Attach counterbalance spring (43) to upper elevator tubes with bolt (39) and nut (9) in location
shown. Stretch spring to lower elevator tubes and attach with hardware as shown.
12.
WARNING!
WARNING!
USE EYE PROTECTION
WHEN INSTALLING
SPRINGS.
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
9
43
39
9
43
39
25
11/05
ID# M731321
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Install net (26) as shown.
B.
D.
A.
26
NOTE: Slide counterbalance
sping against elevator tubes.
20
C.
Lock elevator system into highest position (so the backboard is as high as it will go). Apply 10
ft. height indication sticker (37) to adjustment rod (52) directly below arrow on handle as shown.
Move elevator system to the next position and apply the 91/2 ft. sticker. Repeat until all height
settings have been labeled. (8-10 ft.)
14.
37
52
26
ID# M731321
11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Roll completed assembly to desired position. Fill tank with water (approx. 30 gallons/115
Liters) or sand (approx. 300 lbs./136 kg) and snap cap (24) in place.
15.
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
DO NOT LEAVE ASSEMBLY
UNATTENDED WHEN EMPTY;
IT MAY TIP OVER.
24
24
CAUTION
ADD TWO GALLONS (7.6 LITERS) OF
NON-TOXIC ANTIFREEZE IN SUB-
FREEZING CLIMATES.
NOTE:
IF USING SAND:
2 GALLONS OF
ANTI-FREEZE IS
NOT REQUIRED
NOTE:
Peel protective
film from surface
of acrylic
backboard prior
to use.
27
11/05
ID# M731321
Download from Www.Somanuals.com. All Manuals Search And Download.
16.
Pull trigger (33). Move elevator system up or down to desired height, release trigger (33) to lock
system into one of the five height settings.
WARNING!
DO NOT ALLOW
CHILDREN TO
33
ADJUST HEIGHT.
Apply the height adjustment and moving label (25) to the front of the pole as shown.
17.
25
10 ft.
(3.05 m)
28
ID# M731321
11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
|