Customer Service Center
N53 W24700 South Corporate Circle
Sussex, WI 53089
U.S.A.
A Huffy Company
WRITE IN YOUR MODEL NUMBER:___________
Portable Basketball System
Owners Manual
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN
SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe
operation of the system.
To ensure safety, do not attempt to assemble this system without following the
instructions carefully. Proper and complete assembly, use and supervision is
essential for proper operation and to reduce the risk of accident or injury. A high
probability of serious injury exists if this system is not installed, maintained, and
operated properly. Check entire box and inside all packing material for parts
and/or additional instructional material. Before beginning assembly, read the
instructions and identify parts using the hardware identifier and parts list in this
document.
• If using a ladder during assembly, use extreme caution.
• Two (2) people are recommended for this operation.
• Check base regularly for leakage. Slow leaks could cause system to tip over
unexpectedly.
• Seat the pole sections properly (if applicable). Failure to do so could allow the pole
sections to separate during play and/or transport of the system.
• Climate, corrosion or misuse could result in system failure.
• If technical assistance is required, contact the manufacturer.
• Minimum operational height is 6'6" (1.98 m) to the bottom of backboard.
• This equipment is intended for home recreational use only and NOT
excessive competitive play.
• Read and understand the warning label affixed to pole. Label is shown on page 2.
• The life of your basketball pole depends on many conditions. The climate,
placement of the pole, the location of the pole, exposure to corrosives such as
pesticides, herbicides or salts are all important.
REQUIRED TOOLS AND
MATERIALS:
• If technical assistance is required, contact Huffy Sports.
• Adult supervision is recommended when adjusting height.
• Two People
• Water or Sand 360 lb.
• Wood Board (Scrap)
• Tape Measure
• Step Ladder 8 ft. (2.4 m)
• Tape
(163 kg)
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this system.
• Hammer
• Wrench: 1/2”
• Support Table
For more information on assembly, placement, proper use and maintenance, visit
In U.S. and Canada only: Have questions...don’t go back to the store!
We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection. Although
great care and effort have been taken, occasionally problems may occur. To ensure prompt and correct handling of any problems, or to
answer any questions, please contact our Toll-Free Customer Service Number listed below. Service will be quicker if you have your
Model Number (found on carton) and assembly instructions ready when calling. PLEASE WRITE YOUR MODEL NUMBER IN
THE SPACE PROVIDED ABOVE.
Toll-Free Customer Service Number for U.S: 1-800-558-5234
Canada Only: 1-800-284-8339
Internet Address: http://www.huffysports.com
printed on recycled paper
1
5/99
P/N 211387
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT! WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1 OF THIS OWNERS MANUAL
2
1.
Remove contents from tank (1).
1
3
2.
Turn tank (1) bottom side up. Insert axle rod (2)
through wheel (3), as shown. Secure wheel assembly
to tank by tapping wheel assembly downward with
hammer. It will snap into position. Repeat for opposite
side, then carefully turn tank over.
3.
Correctly identify each pole section and
mark indicated distance from end of
4
bottom pole section (4) with tape as shown.
6
5
BOTTOM
MIDDLE
TOP
5”
(13 cm)
Slide top of upper pole section (5) through bottom of middle pole section (6). Secure top
and middle pole sections together in both locations as shown, using carriage bolts (7),
washers (8), adjustment knob (9), and flange nut (13).
4.
IMPORTANT! This step MUST be completed before going on to step 5.
“Bottom of middle
pole section”
“Top of upper
pole section”
5
6
5
6
7
9
8
6
5
8
13
NOTE: Top pole section will slide
through middle pole section.
7
printed on recycled paper
3
5/99
P/N 211387
Download from Www.Somanuals.com. All Manuals Search And Download.
Add bottom pole section (4) to assembly as
shown and bounce until completely tight.
5.
*
5
IMPORTANT!
Holes in top and bottom pole
sections MUST align to correctly
position elevator system.
6
Continue to check alignment
while assembling pole sections.
Row of 3 holes on top pole
section must be parallel with
adjustment knob.
*
Once assembled, pole
sections can NOT be
separated!
POLES MUST OVERLAP
3-1/2” (9 CM) MINIMUM.
6
NOTE: Discard this carriage
bolt immediately after completing
this step. DO NOT discard flange
nut and washer.
4
WOOD SCRAP
printed on recycled paper
4
P/N 211387
5/99
Download from Www.Somanuals.com. All Manuals Search And Download.
14
13
6.
Attach base pole bracket (10) and base strut
brackets (11) to base (1) as shown below.
15
12
12
11
1
10
12
11
10
8
15
13
8
7.
Attach struts (14) as shown above.
8
13
13
14
13
13
16
8.
Attach pole strut bracket (16) to
struts (14) as shown at left.
14
17
9.
Place tank (1) in desired location. Fill tank (1)
with water (30 gallons (114 liters)) or sand (360
lb. (163 kg)). Snap tank cap (18) in place.
18
SAN
A
SAND
IMPORTANT!
SA
ND
Add two gallons (7.6 liters) of
NON-TOXIC ANTIFREEZE
in sub-freezing climates.
T
1
printed on recycled paper
5
5/99
P/N 211387
Download from Www.Somanuals.com. All Manuals Search And Download.
10.
Rest pole assembly on FILLED tank.
WARNING
KEEP UNNECESSARY
PRESSURE OFF OF THE
POLE ASSEMBLY WHEN IN
THIS POSITION. TWO
PEOPLE RECOMMENDED
FOR THIS STEP.
13
11.
Attach pole assembly to pole bracket (10) as
8
19
shown. NOTE: Keep unnecessary pressure off
of the pole assembly when in this position. Two
people recommended for this step.
10
8
21
12. Attach upper pole mounting bracket (20) to swivel
bracket (21) and fully tighten.
22
23
20
13
12
12
Attach lower halves of backboard
brackets (23) to swivel bracket (21).
NOTE: Keep hardware loose until
after alignment in step 16.
13.
21
12
13
printed on recycled paper
6
P/N 211387
5/99
Download from Www.Somanuals.com. All Manuals Search And Download.
25
13
5
14.
NOTE: Two people recommended for this
procedure. Attach bracket assembly to top pole
section (5). Secure hardware as shown and
tighten completely. Install pole cap (25).
PLAY
POSITION
8
24
STORAGE
POSITION
7
27
15.
Bend upper halves of backboard brackets (23) to
line up with mounting holes on backboard as shown.
26
23
27
27
23
Attach back bracket (26) to backboard and
backboard brackets (23) as shown and finger
16.
tighten. NOTE: Do NOT tighten completely. Final
adjustments will be made in step 24.
13
13
printed on recycled paper
7
5/99
P/N 211387
Download from Www.Somanuals.com. All Manuals Search And Download.
22
28
17. Assemble rim (28) to back bracket (26) as shown.
8
29
31
30
33
26
32
31
To keep rim components from shifting during installation
procedure, install knob set (32 and 33) through spacer
(31) in the upper set of holes in rim bracket as shown.
18.
Install net clips (34) on rim
OUTSIDE VIEW
19.
(28).
The two outer hooks on net clip must face
towards inside of goal rim. Insert larger hole
in net clip onto rim stud, push down on net
clip, then slide net clip right, locking or
snapping securely into position (clips must
"snap" into place to insure a secure fit).
NOTE: Net clips should not slide with
ease. It is very important that the net clips
are in the locked position before going on
to next step
34
WARNING
28
USE OF THIS PRODUCT WITHOUT
PROPER INSTALLATION OF NET
CLIPS, OR WHEN ALL NET CLIPS
ARE NOT PRESENT COULD
RESULT IN BODILY HARM.
BE SURE TO FOLLOW
The Quick Clip™ rapid release net system lets the net pull away from the rim. This reduces
the risk of player injury or property damage. However, improper installation or a ball
making contact at an odd angle may disengage the net clip from the goal rim. Usually, the
clip is reinstalled with little or no problem. We hope that you agree this inconvenience is
minor when compared to the safety of the players.
DIRECTIONS CAREFULLY.
Quick Clip: US Patent No. 5,792,010/5,795,253
20.
Install net (35).
INSIDE VIEW
28
NOTE: Stretching net
up then pulling side to
side will help snap net
under center hook.
IMPORTANT! MAKE
SURE NET IS HELD BY
35
ALL THREE HOOKS ON
THE NET CLIP.
printed on recycled paper
8
P/N 211387
5/99
Download from Www.Somanuals.com. All Manuals Search And Download.
1
21.
Attach nylon tie down stake rope (36)
to tank (1) as shown.
36
36
Secure unit to ground using nylon
22.
rope (36) and tie down stake (37).
37
9
8
23.
4
Carefully upright pole and backboard assembly. Secure
strut assembly (14) to bottom pole section (4) as shown.
14
38
TWO PERSON MINIMUM REQUIRED
FOR THIS PROCEDURE. NOT
FOLLOWING RECOMMENDATION MAY
RESULT IN SERIOUS BODILY INJURY
AND/OR PROPERTY DAMAGE.
40
Regulation
rim height
is 10 feet
(3.05 m).
NOTE: Two people recommended for this procedure. Level backboard
and rim adjust hardware from step 13 and 16. Tighten completely.
24.
10 feet
(3.05 m)
Apply height adjustment label (40) to front of pole as shown.
25.
printed on recycled paper
9
5/99
P/N 211387
Download from Www.Somanuals.com. All Manuals Search And Download.
HEIGHT ADJUSTMENT
Rest unit on support table.
Remove adjustment knob (9),
carriage bolt (7), and washer (8)
to extend or retract pole. Pole
adjusts from 71/2’ to 10’.
1.
9
WARNING
BACKBOARD AND TOP POLE
MAY
ROTATE
HEIGHT ADJUSTMENT.
DURING
8
Re-Insert Adjustment set
(7, 8, 9) When pole is at
desired height.
7
SUPPORT TABLE
TO PLACE IN THE STORAGE POSITION
1.
2.
Lower backboard and rim down to the
lowest position (71/2’ (2.29 m)).
Remove adjustment knob (9), washer
(8), and carriage bolt (7). Carefully
rotate pole downward towards
ground.
WARNING
DO NOT STAND BEHIND
SYSTEM WHEN PREPARING
FOR STORAGE.
3.
7
Secure pole assembly to tank (1) with carriage
bolt (7), washer (8), and adjustment knob (9).
Remove adjustment knob (24) from swivel
bracket (21) and carefully rotate backboard
assembly 180º.
1
PLAY
POSITION
24
8
8
9
STORAGE
POSITION
4.
Secure backboard assembly in storage position
with adjustment knob set (24 and 8) as shown.
printed on recycled paper
10
P/N 211387
5/99
Download from Www.Somanuals.com. All Manuals Search And Download.
33
5.
Remove knob set (32, 31, and 33) from the rim assembly
and re-insert knob set into top locking position.
32
31
6.
Carefully rotate system up on its side to remove
water or sand from tank.
39
36
39
36
50"
(127 cm)
7.
Secure screw hook (39) into wall, approximately
50” (127 cm) up from floor as shown.
IMPORTANT! It is necessary to install screw hook
into a wall stud.
8.
Remove tie down stake (37) from ground and
detach rope (36). Rotate system up onto the front
wheels and roll toward the wall. Secure system with
rope (36) on screw hook (39).
printed on recycled paper
11
5/99
P/N 211387
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Item Qty. Part No. Description
Item Qty. Part No. Description
1
2
1
2
2
1
1
1
4
206903 Tank
21
22
23
24
25
26
27
28
29
30
31
32
33
1
2
2
1
1
1
6
1
1
1
2
1
1
206912 Bracket, Swivel, 3-3/4 x 2-1/4
203099 Locknut, 5/16-18, Nylon Insert
906633 Bracket, Backboard
206629 Knob, Threaded, 5/16-18
206641 Pole Cap, 2-3/4
206327 Wheel Axle
3
226401 Wheel
4
908492 Bottom Pole Section
906643 Top Pole Section
906642 Middle Pole Section with Label
203231 Bolt, Carriage, 5/16-18 x 3-1/2 Long
5
6
906625 Bracket, Back
7
203157 Bolt, Carriage, 5/16-18 x 2-1/4
900931 Rim
8
12 203218 Washer, 5/16 Flat
9
2
1
2
203435 Knob, Plastic, 3 Diameter
206911 Bracket, Base Pole
206004 Bolt, Carriage, 5/16-18 x 6
206005 Stop Washer
10
11
12
13
14
15
16
17
18
19
20
206910 Bracket, Base Strut, 2 x 1.2
202790 Spacer, 5-1/4 Long
11 203223 Bolt, Carriage, 5/16-18 x 1
23 203100 Nut, Hex Flange, 5/16-18
206639 Knob, Threaded, 3/8-16 x 5-3/4
203429 Knob, Plastic, 1" diameter, 3/8 nut
2
2
1
2
2
1
1
906918 Tank Strut
34 12* 200121 Clips
203084 Bolt, Carriage, 5/16-18 x 1-3/4
906914 Bracket, Pole Strut
35
36
37
38
39
40
1
1
1
1
1
1
204281 Net
204444 Rope Nylon, Double Loop, 1’ x 24"
203124 Tie down Stake
203217 Bolt, Carriage, 5/16-18 x 1-1/2
203617 Tank Cap, 1 3/4
206909 Bolt, Carriage, 5/16-18 x 5-1/2
203449 Hook Screw
206110 Bolt, Carriage, 5/16-18 x 3-3/4
206916 Bracket, Upper Pole Mounting
201259 Label, Height Adjustment and Moving
* You may have extra parts with this model.
HARDWARE IDENTIFIER
Item #7 (4)
Item #12 (11)
Item #8 (11)
Item #17 (2)
Item #15 (2)
Item #13 (23)
Item #19 (1)
Item #22 (1)
* YOU MAY HAVE EXTRA PARTS WITH THIS MODEL.
printed on recycled paper
12
P/N 211387
5/99
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (continued)
Item #27 (6)
Item #34 (12)*
Item #29 (1)
Item #31 (2)
Item #30 (1)
Item #38 (1)
Item #39 (1)
printed on recycled paper
13
5/99
P/N 211387
Download from Www.Somanuals.com. All Manuals Search And Download.
|