Hotpoint Washer WMD 960 A User Manual

Instructions for use

WASHING MACHINE

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

English, 1

Technical data

Description of the washing machine, 6-7

Control panel

Display

Running a wash cycle, 8

Wash cycles and functions, 9

Table of wash cycles

Wash functions

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

WMD 960 A

Special wash cycles

Load balancing system

Precautions and tips, 11

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 12

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 13

Assistance, 14

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the drain hose

Connect the drain

• the supply voltage is included within the values

indicated on the Technical details table

(see page 5);

hose, without bending

it, to a draining duct or

a wall drain situated

between 65 and 100 cm

from the floor;

• the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

65 - 100 cm

Your appliance is now supplied with a 13 amp fused

plug it can be plugged into a 13 amp socket for

immediate use. Before using the appliance please

read the instructions below.

The drain hose may be

connected to an under-

sink trap. Before

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED

OUT BY A QUALIFIED ELECTRICIAN.

connecting the drain

hose from the machine

ensure that any blanks

or removable ends have

been taken off the

spigot.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used,

and the fuse cover re-fitted. If the fuse cover is

lost, the plug must not be used until a replacement

is obtained.

Replacement fuse covers:

If it is place over the

edge of a basin or sink

be sure the free end

of the hose should not

be underwater.

If a replacement fuse cover is fitted, it must be of

the correct colour as indicated by the coloured

marking or the colour that is embossed in words on

the base of the plug. Replacements can be obtained

directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable

through partitions, units etc., please ensure that

either:

! We advise against the use of hose extensions; in

case of absolute need, the extension must have

the same diameter as the original hose and must

not exceed 150 cm in length.

the plug is replaced by a fused 13 ampere re-

wearable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with

BS 5733) which is accessible without moving the

appliance.

Ensure that if the drain hose is pushed into a

standpipe, that the end does not go down more

than 15cms (6 inches). If the hose is pushed down

too far, this may cause the machine to self -

syphon ie. continuously empty as it is filling.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be

accidentally inserted into a socket.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

Instructions for connecting cable to an alternative

plug:

• the socket is earthed and in compliance with

the applicable law;

Important: the wires in the mains lead are coloured

in accordance with the following code:

Green & Yellow E a r t h

• the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (see page 5);

B l u e

B r o w n

N e ut r a l

L i v e

Download from Www.Somanuals.com. All Manuals Search And Download.

As the colours of the wires in the lead may not

correspond with the coloured markings identifyng

the terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E

Warning! The company denies all liability if and

when these norms are not respected.

The first wash cycle

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, setting the 90°C

programme without a pre-wash cycle.

Connect Blue wire to terminal marked N or coloured

Black.

If a 13 amp plug (BS 1363) is used it must be fitted

with a

13 amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

B L U E

B R O W N

GREEN

NEUTRAL (N)

LIVE (L)

EARTH (E)

YELLOW

Disposing of the appliance:

When disposing of the appliance please remove the

plug by cutting the mains cable as close as possible to

the plug body and dispose of it as described above.

GREEN &

YELLOW

13 ampere fuse

BROWN

CROSS-BAR

CORD GRIP

BLUE

! The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to

leave it exposed to rain and thunderstorms.

! When the washing machine is installed, the mains

socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent or

dangerously compressed.

! The power supply cable must only be replaced by

an authorised serviceman.

Download from Www.Somanuals.com. All Manuals Search And Download.

Technical data

Model

WMD 960 A

width 59.5 cm

height 85 cm

depth 60 cm

Dimensions

Capacity

from 1 to 8 kg

Electrical

please refer to the technical data plate

fixed to the machine

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 58 litres

Water

connections

Spin speed

up to 1600 rotations per minute

Energy rated

programmes

according to

regulation

programme

(1^stpress of the button);

temperature 60°C;

using a load of 8 kg.

EN 60456

This appliance conforms to the

following EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2002/96/EC

- 2006/95/EC (Low Voltage)

Download from Www.Somanuals.com. All Manuals Search And Download.

Description of the washing machine

Control panel

CHILD

LOCK button

SPIN SPEED

button

O N / O F F

button

DISPLAY

S TA RT/

PA U S E

button with

indicator light

Detergent dispenser

drawer

MEMORY

button

F U N C T I O N

buttons

WASH

CYCLE

SELECTOR

buttons

DELAY

START button

T E M P E R AT U R E

button

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents

and laundry”).

TEMPERATURE button : press to decrease the

temperature: the value will be shown on the display.

CHILD LOCK button: to activate the control panel

lock, press and hold the button for approximately 2

seconds. When the symbol is illuminated, the

control panel is locked. This means it is possible to

prevent wash cycles from being modified

accidentally, especially where there are children in

the home. To deactivate the control panel lock,

press and hold the button for approximately 2

seconds.

ON/OFF button : press this briefly to switch the

machine on or off. The START/PAUSE indicator light,

which flashes slowly in a green colour shows that

the machine is switched on. To switch off the

washing machine during the wash cycle, press and

hold the button for approximately 2 seconds; if the

button is pressed briefly or accidentally the

machine will not switch off. If the machine is

switched off during a wash cycle, this wash cycle

will be cancelled.

DELAY START button

: press to set a delayed

start time for the selected wash cycle. The delay

time will be shown on the display.

WASH CYCLE SELECTOR buttons: used to set

the desired wash cycle (see "Table of wash cycles").

START/PAUSE button with indicator light: when

the green indicator light flashes slowly, press the

button to start a wash cycle. Once the cycle has

started the indicator light will remain lit in a fixed

manner. To pause the wash cycle, press the button

again; the indicator light will flash in an orange

MEMORY button: press and hold the button to

store a cycle with your own set of preferences in

the memory of the machine. To recall a previously

stored cycle, press the MEMORY button.

FUNCTION buttons: press the button to select

the desired function. The corresponding indicator

light on the display will switch on.

colour. If the symbol

is not illuminated, the door

may be opened. To start the wash cycle from the

point at which it was interrupted, press the button

again.

SPIN button

: press to reduce or completely

exclude the spin cycle - the value is indicated on the

display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Display

The display is useful when programming the machine and provides a great deal of information.

The two upper text strings A and B provide details of the wash cycle you have selected, the wash cycle phase

in progress at any given time and all information relating to the progress status of the wash cycle.

String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has

been set, the time remaining until the start of the selected wash cycle.

String D shows the maximum spin speed value (this depends on the selected wash cycle, or any modification

you have made by pressing the spin speed button); if the wash cycle does not include a spin cycle, the string

remains unused.

String E shows the maximum temperature value which may be selected (this depends on the wash cycle, or

any modification you have made by pressing the temperature button); if the temperature of the wash cycle

cannot be modified, the string remains unused.

Indicator lights F correspond to the functions and light up when the selected function is compatible with the

set wash cycle.

Door locked symbol

If the symbol is lit, this indicates that the washing machine door is locked to prevent it from being opened

accidentally. To prevent any damage from occurring, wait for the symbol to switch itself off before opening

the appliance door.

N.B.: if the DELAYED START function has been activated, the door cannot be opened; pause the machine by

pressing the START/PAUSE button if you wish to open it.

! The first time the machine is switched on, you will be asked to select the language and the display will

automatically show the language selection menu.

To select the desired language press the TEMPERATURE and SPIN buttons; to confirm the selection press the

CHILD LOCK button.

If you wish to select another language, press and hold the CONTROL PANEL LOCK + TEMPERATURE + SPIN

buttons simultaneously for 5 seconds, then repeat the steps listed above.

Download from Www.Somanuals.com. All Manuals Search And Download.

Running a wash cycle

1. SWITCH THE MACHINE ON. Press the On/Off

button ; the text HELLO will appear on the

display and the START/PAUSE indicator light will

flash slowly in a green colour.

! If the selected function is not compatible with

another function which has been selected

previously, the indicator light corresponding to

the first function selected will flash and only the

second function will be activated; the indicator

light corresponding to the enabled function will

remain lit.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes on the following page.

! The functions may affect the recommended load

value and/or the duration of the cycle.

3. MEASURE OUT THE DETERGENT. Open the

detergent dispenser drawer and pour the

detergent into the relevant compartments as

described in "Detergents and laundry".

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light

will become green, remaining lit in a fixed manner,

and the door will be locked (the DOOR LOCKED

symbol will be on). During the wash cycle, the

name of the phase in progress will appear on the

display. To change a wash cycle while it is in

progress, pause the washing machine using the

START/PAUSE button (the START/PAUSE indicator

light will flash slowly in an orange colour); then

select the desired cycle and press the START/

PAUSE button again.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Press one of the

WASH CYCLE SELECTOR buttons to select the

required wash cycle; the name of the wash cycle

will appear on the display. A temperature and spin

speed is set for each wash cycle; these may be

adjusted. The duration of the cycle will appear on

the display.

To open the door while a cycle is in progress,

press the START/PAUSE button; if the DOOR

6. CUSTOMISE THE WASH CYCLE. Use the

relevant buttons:

LOCKED

symbol is switched off the door may

be opened. Press the START/PAUSE button again

to restart the wash cycle from the point at

which it was interrupted.

Modifying the temperature and/or

spin speed. The machine automatically selects

the maximum temperature and spin speed set

for the selected wash cycle; these values cannot

therefore be increased. The temperature can be

8. THE END OF THE WASH CYCLE. This will be

indicated by the text "END OF CYCLE" on the

display; when the DOOR LOCKED

symbol

decreased by pressing the

button, until the

switches off the door may be opened. Open the

door, unload the laundry and switch off the

machine.

cold wash "OFF" setting is reached. The spin

speed may be progressively reduced by pressing

the

button, until it is completely excluded (the

"OFF" setting). If these buttons are pressed

again, the maximum values are restored.

! If you wish to cancel a cycle which has already

button. The cycle will

begun, press and hold the

be stopped and the machine will switch off.

Setting a delayed start.

To set a delayed start for the selected

programme, press the corresponding button

repeatedly until the required delay period has

been reached. When this option is enabled, the

symbol lights up on the display. To remove the

delayed start function press the button until the

text "OFF" appears on the display.

Modifying the cycle settings.

• Press the button to enable the function; the

indicator light corresponding to the button will

switch on.

• Press the button again to disable the function;

the indicator light will switch off.

! If the selected function is not compatible with

the programmed wash cycle, the indicator light

will flash and the function will not be activated.

Download from Www.Somanuals.com. All Manuals Search And Download.

Wash cycles and functions

Table of wash cycles

Max. Max.

load (kg) load (kg)

Detergents

Max. Max.

Cycle

duration

Description of the wash cycle

temp. speed

(°C) (rpm)

Fabric

softener

Wash

Normal Mini load

Everyday wash cycles (Daily)

Cottons (*) (1^stpress of the button): extremely soiled whites.

90°

60°

40°

50°

40°

30°

60°

1600

800

Cottons ⁽²^nd^{press of the button)}: heavily soiled whites and resistant colours.

Cottons (3^rdpress of the button): heavily soiled whites and delicate colours.

Synthetics (1^stpress of the button): heavily soiled resistant colours.

Synthetics (2^ndpress of the button): lightly soiled resistant colours.

Synthetics (3^ndpress of the button): lightly soiled resistant colours.

Bed & Bath: washes bathroom laundry and bedlinen.

3,5

1,5

800

1600

Fastwash 60' (1^stpress of the button): to refresh lightly soiled garments quickly

(not suitable for wool, silk and clothes which require washing by hand).

Fastwash 30' (2^nd^{press of the button)}: to refresh lightly soiled garments quickly

(not suitable for wool, silk and clothes which require washing by hand).

Special cycles / Memory

60°

30°

800

3,5

1,5

Memory: allows for any wash cycle to be stored.

Wool: for wool, cashmere, etc.

40°

30°

600

Silk/Curtains: for garments in silk and viscose, lingerie.

Partial wash cycles

Fast Spin cottons (1^stpress of the button)

Slow spin delicates ⁽²^ndpress of the button)

Rinse cottons (1^stpress of the button)

Pump out (2^ndpress of the button)

1600

800

1600

3,5

For allTestInstitutes:

*TestwashcycleincompliancewithregulationEN60456:setwashcyclewithatemperatureof60°C.

Wash functions

Super Wash

Because a greater quantity of water is used in the

initial phase of the cycle, and because of the

increased cycle duration, this function offers a

high-performance wash.

Mini Load

This function is recommended for when the load of

laundry is equal to half, or less than half, of the

maximum recommended load (see Table of wash

cycles).

! It cannot be used in conjunction with the

“Fastwash 30’”,

and “Pump out” programmes.

! It cannot be used with the

wash cycles”.

and “Partial

Timer Saver

Reduces the duration of the wash cycle.

Reduced Creases

By selecting this function, the wash and spin cycles

will be modified in order to reduce the formation of

creases. At the end of the cycle the washing machine

will perform slow rotations of the drum; the “Reduced

creases” and START/PAUSE indicator lights will flash

(orange) and the text "END OF CYCLE" will appear on

the display. To end the cycle, press the START/PAUSE

button or the “Reduced creases” button.

! It cannot be used with the

wash cycles”.

and “Partial

Eco Wash

The Eco Wash function saves energy by not heating

the water used to wash your laundry – an advantage

both to the environment and to your energy bill.

Instead, intensified wash action and water

optimisation ensure great wash results in the same

average time of a standard cycle.

For the Silk/Curtains cycle, the machine will end the

cycle while the laundry is soaking; the “Reduced

creases” and START/PAUSE indicator lights will flash

(orange) and the text "RINSE HOLD" will appear on the

display. To drain the water so that the laundry may be

removed, press the START/PAUSE button or the

“Reduced creases” button.

For the best washing results we recommend the

usage of a liquid detergent.

! It cannot be used with the

wash cycles”.

and “Partial

! It may not be used with the , “Fastwash 30’”,

and “Pump out” programmes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Detergents and laundry

Detergent dispenser drawer

Special wash cycles

Good washing results also depend on the correct

dose of detergent: adding too much detergent will

not necessarily result in a more efficient wash, and

may in fact cause a build up on the inside of your

appliance and contribute to environmental pollution.

Fastwash 30’: this wash cycle was designed to

wash lightly soiled garments quickly: it lasts just 30

minutes and therefore saves both energy and time.

By selecting this wash cycle ( at 30°C), it is

possible to wash different fabrics together (except

for wool and silk items), with a maximum load of 3 kg.

! Do not use hand washing detergents because

these create too much foam.

Silk: use special wash cycle

to wash all silk

garments. We recommend the use of special

detergent which has been designed to wash delicate

clothes.

Open the detergent

dispenser drawer and

pour in the detergent or

washing additive, as

follows.

Curtains: fold curtains and place them in a pillow

case or mesh bag. Use wash cycle

Wool: Hotpoint is the only washing machine

manufacturer to have been awarded the

prestigious Woolmark Platinum Care endorsement

(M.0508) by the Woolmark Company, which means

that all woollen garments may be washed in the

washing machine, even those which state “hand

wash only”

on the label. Wash cycle

therefore

offers complete peace of mind when washing

woollen garments in the washing machine (max. load

2 kg) and guarantees optimal performance.

! Do not pour detergent into the middle compartment (*).

Detergent should only be poured into the compartment 1.

compartment 1: Detergent for the wash

cycle (powder or liquid)

Load balancing system

For best results liquid detergent should be poured

in the dispenser immediately before the start of

the programme.

Before every spin cycle, to avoid excessive vibra-

tions and to distribute the load in a uniform man-

ner, the drum rotates continuously at a speed

which is slightly greater than the washing rotation

speed. If, after several attempts, the load is not

balanced correctly, the machine spins at a reduced

spin speed. If the load is excessively unbalanced,

the washing machine performs the distribution

process instead of spinning. To encourage improved

load distribution and balance, we recommend small

and large garments are mixed in the load.

compartment 2: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from

whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the listed values, which refer to the

weight of the laundry when dry:

Durable fabrics: max. 8 kg

Synthetic fabrics: max. 3,5 kg

Delicate fabrics: max. 2 kg

Wool: max. 2kg

Silk: max. 2 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions and tips

! This washing machine was designed and

constructed in accordance with international

safety regulations. The following information is

provided for safety reasons and must therefore be

read carefully.

Opening the porthole door manually

In the event that it is not possible to open the

porthole door due to a powercut, and if you wish to

remove the laundry, proceed as follows:

1. remove the plug from

the electrical socket.

2. make sure the water

level inside the machine is

General safety

• This appliance was designed for domestic use only.

• The washing machine must only be used by adults, in

accordance with the instructions provided in this manual.

lower than the door

opening; if it is not,

• Do not touch the machine when barefoot or with

wet or damp hands or feet.

remove excess water

using the drain hose,

collecting it in a bucket as

indicated in the figure.

• Do not pull on the power supply cable when

unplugging the appliance from the electricity

socket. Hold the plug and pull.

• Do not open the detergent dispenser drawer

while the machine is in operation.

3. using a screwdriver,

remove the cover panel on

the lower front part of

the washing machine (see

figure).

• Do not touch the drained water as it may reach

extremely high temperatures.

• Never force the porthole door. This could damage

the safety lock mechanism designed to prevent

accidental opening.

• If the appliance breaks down, do not under any

circumstances access the internal mechanisms

in an attempt to repair it yourself.

• Always keep children well away from the appliance

while it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group

of two or three people and handle it with the

utmost care. Never try to do this alone, because

the appliance is very heavy.

• Before loading laundry into the washing machine,

make sure the drum is empty.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires

that old household electrical appliances must not

be disposed of in the normal unsorted municipal

waste stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

4. pull outwards using the tab as indicated in the

figure, until the plastic tie-rod is freed from its

stop position; pull downwards and open the door at

the same time.

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Care and maintenance

Cutting off the water and

electricity supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system

inside the washing machine and help to prevent

leaks.

• Unplug the washing machine when cleaning it and

during all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth soaked

in lukewarm soapy water. Do not use solvents or

abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pulling it

out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of

your appliance

• Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump which does not require any maintenance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there

are any cracks, it should be replaced immediately:

during the wash cycles, water pressure is very

strong and a cracked hose could easily split open.

! Never use second-hand hoses.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see

“Assistance”), make sure that the problem cannot be not solved easily using the following list.

Problem:

Possible causes / Solutions:

The washing machine does not

switch on.

• The appliance is not plugged into the socket fully, or is not making contact.

• There is no power in the house.

The wash cycle does not start.

• The washing machine door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set (see “Running a wash cycle”).

The washing machine does not

take in water (the text "NO

WATER, CHECK SUPPLY"

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

appears on the display).

• The START/PAUSE button has not been pressed.

The washing machine

continuously takes in and

drains water.

• The drain hose is not fitted at a height between 65 and 100 cm from

the floor (see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water

tap, switch the appliance off and contact the Assistance Service. If

the dwelling is on one of the upper floors of a building, there may be

problems relating to water drainage, causing the washing machine to

fill with water and drain continuously. Special anti-draining valves are

available in shops and help to avoid this inconvenience.

The washing machine does not

drain or spin.

• The wash cycle does not include draining: some wash cycles require the

drain phase to be started manually (see “Wash cycles and functions”).

• The “Reduced creases” function has been activated: To complete the wash

cycle, press the START/PAUSE button (see “Wash cycles and functions”).

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

The washing machine vibrates a • The drum was not unlocked correctly during installation (see “Installation”).

lot during the spin cycle.

• The washing machine is not level (see “Installation”).

• The washing machine is trapped between cabinets and walls (see “Installation”).

The washing machine leaks.

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see

“Care and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

The machine is locked and the

display flashes, indicating an

error code (e.g. F-01, F-..).

• Switch off the machine and unplug it, wait for approximately 1

minute and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

There is too much foam.

• The detergent is not suitable for machine washing (it should display the

text “for washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

Download from Www.Somanuals.com. All Manuals Search And Download.

Assistance

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of

breakdown repairs for twelve months from the date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be defective

because of either workmanship or materials, we will, at our discretion, either repair or replace the

appliance at no cost to you.

This guarantee is subject to the following conditions:

The appliance has been installed and operated correctly and in accordance with our

operating and maintenance instructions.

The appliance is used only on the electricity or gas supply printed on the rating plate.

The appliance has been used for normal domestic purposes only.

The appliance has not been altered, serviced, maintained, dismantled, or otherwise

interfered with by any person not authorised by us.

Any repair work must be undertaken by us or our appointed agent.

Any parts removed during repair work or any appliance that is replaced become our property.

The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

Damage resulting from transportation, improper use, neglect or interference or as a result

of improper installation.

Replacement of any consumable item or accessory . These include but are not limited to: plugs,

cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.

Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL

OR NON-DOMESTIC PREMISES.

5 Year Parts Guarantee

Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on

you registering your appliance with us and the parts being fitted by one of our authorised engineers.

There will be a charge for our engineer's time. To activate the extra parts warranty on your

appliance, simply call our registration line on 0870 6092094 (ROI 01 230 0800).

Extended Guarantees

We offer a selection of repair protection plans that enable you to fully cover yourself against the expense

of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on

08709 088 088 (ROI 01 230 0233).

Free Helpdesk Service

We have a dedicated team who can provide free advice and assistance with your appliance if you

experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint

Service Hotline on 08709 066 066 (ROI 0818 313 413) for telephone assistance, or, where

necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will

replace your machine or, if you prefer, give you your money back.

Download from Www.Somanuals.com. All Manuals Search And Download.

After Sales Service

No one is better placed to care for your Hotpoint appliance during the course of its

working life than us - the manufacturer.

Essential Contact Information

Hotpoint Service

We are the largest service team in Europe offering you access to 400 skilled telephone advisors and

1100 fully qualified engineers on call to ensure you receive fast, reliable, local service.

UK: 08709 066 066

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Please note: Our advisors will require the following information:

Model number:

Serial number:

Parts and Accessories

We supply a full range of genuine replacement parts as well as accessory products that protect and

hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.

UK: 08709 077 077

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Appliance Registration

We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts

guarantee you must register your appliance with us.

UK: 0870 6092094

Republic of Ireland: 01 230 0800

www.hotpointservice.co.uk

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB

Indesit Company Unit 49 Airways Industrial Estate,Dublin 17

Recycling & Disposal Information

As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right

to use quality, recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,

remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts

separately to ensure that the appliance can no longer be plugged into a mains socket, and the door

cannot be locked shut.

Download from Www.Somanuals.com. All Manuals Search And Download.

195068514.00

01/2008

Xerox Business Services

Download from Www.Somanuals.com. All Manuals Search And Download.

Grizzly Car Stereo System G4014 User Manual
Grundig Vacuum Cleaner VCH7830 User Manual
Haier Paint Sprayer DW12 CBE6 User Manual
Hamilton Beach Coffeemaker D45012W User Manual
HP Hewlett Packard Calculator 8656A User Manual
Humax Flat Panel Television LGB 19DRT User Manual
Husqvarna Plumbing Product D404558 User Manual
Hustler Turf Lawn Mower M 1 User Manual
IDEAL INDUSTRIES Paper Shredder 2350 Cross Cut User Manual
Ikelite Digital Camera DSC P150 User Manual