Instructions for Installation and Use
Washer-dryer
Model BWD 129
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions for use
WASHER-DRYER
Contents
GB
Installation, 2-3-4-5-6-7
Unpacking and levelling, 2
GB
Electric and water connections, 2-3
The first wash cycle, 4
Technical details, 5
English,1
Instructions for the fitter, 6-7
Washer-dryer description, 8-9
Control panel, 8
Leds, 9
Starting and Programmes, 10
Briefly: how to start a programme, 10
Programme table, 10
Personalisations, 11
Setting the temperature, 11
Set the drying cycle, 11
Functions, 11
BWD 129
Detergents and laundry, 12
Detergent dispenser, 12
Preparing your laundry, 12
Special items, 12
Woolmark Platinum Care, 12
Precautions and advice, 13
General safety, 13
Disposal, 13
Saving energy and respecting the environment, 13
Care and maintenance, 14
Cutting off the water or electricity supply, 14
Cleaning your appliance, 14
Cleaning the detergent dispenser, 14
Caring for your appliance door and drum, 14
Cleaning the pump, 14
Checking the water inlet hose, 14
Troubleshooting, 15
Service, 17
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
! Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the Washer-dryer to inform
the new owner as to its operation and features.
Levelling your appliance correctly will provide it
with stability and avoid any vibrations, noise and
shifting during operation. If it is placed on a fitted
or loose carpet, adjust the feet in such a way as to
allow enough room for ventilation beneath the
Washer-dryer.
GB
! Read these instructions carefully: they contain
vital information on installation, use and safety.
Electric and water connections
Unpacking and levelling
Connecting the water inlet hose
Unpacking
1. Connect the supply
pipe to the water
mains using a gas 3/4
1. Unpack the Washer-dryer.
2. Check whether the Washer-dryer has been
damaged during transport. If this is the case, do
not install it and contact your retailer.
attachment, fitting
the rubber gasket and
the filter supplied with
the appliance and
3. Remove the four
protective screws and
the rubber washer with
the respective spacer,
situated on the rear of
the appliance (see
figure).
ensuring that they are
fimly tightened to the
taps.
The water supply marked C must be connected to
the cold water tap; the pipe marked H must be
connected to the hot water tap. Both pipes may
be connected to the cold water tap using the
special Y connection with multiple attachments,
supplied with the appliance (see figure).
Before making the connection, allow the water to
run freely until it is perfectly clear.
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need them again if
the Washer-dryer needs to be moved to another
location.
2. Connect the other
end of the water inlet
hose to the Washer-
dryer, screwing it onto
the appliance's cold
water inlet, situated
on the top right-hand
side on the rear of the
appliance (see figure).
! Packaging materials are not children's toys.
Levelling
Your machine may make a considerable amount of
noise if the two front feet have not been adjusted
correctly.
1. Install the Washer-dryer on a flat sturdy floor,
without resting it up against walls, furniture
cabinets or other.
3. Make sure there are no kinks or bends in the hose.
2. If the floor is not
! The water pressure at the tap must be within
the values indicated in the Technical details
table (on the next page).
perfectly level, compen-
sate for any
unevenness by
tightening or loosening
the adjustable front
! If the water inlet hose is not long enough,
contact a specialist store or an authorised
serviceman.
feet (see figure); the
angle of inclination,
measured according to
the worktop, must not
exceed 2°.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the drain hose
Your appliance is now supplied with a 13 amp fused
plug it can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instructions below.
GB
Connect the drain
hose, without bending
it, to a draining duct or
a wall drain situated
between 65 and 100 cm
from the floor;
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
65 - 100 cm
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is
lost, the plug must not be used until a
replacement is obtained.
alternatively, place it
over the edge of a
basin, sink or tub,
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of
the correct colour as indicated by the coloured
marking or the colour that is embossed in words on
the base of the plug. Replacements can be obtained
directly from your nearest Service Depot.
fastening the duct
supplied to the tap
(see figure). The free
end of the hose should
not be underwater.
Removing the plug:
If your appliance has a non-rewireable moulded
plug and you should wish to re-route the mains
cable through partitions, units etc., please ensure
that either:
! We advise against the use of hose extensions; in
case of absolute need, the extension must have
the same diameter as the original hose and must
not exceed 150 cm in length.
the plug is replaced by a fused 13 ampere re-
wearable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp
cable outlet, controlled by a switch, (in compliance
with BS 5733) which is accessible without moving
the appliance.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
Disposing of the plug:
• the socket is earthed and in compliance with
the applicable law;
Ensure that before disposing of the plug itself,
you make the pins unusable so that it cannot be
accidentally inserted into a socket.
• the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (see page 5);
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are
coloured in accordance with the following code:
• the supply voltage is included within the values
indicated on the Technical details table
(see page 5);
Green & Yellow
Blue
Brown
Earth
Neutral
Live
• the socket is compatible with the Washer-
dryer's plug. If this is not the case, replace
the socket or the plug.
As the colours of the wires in the lead may not
correspond with the coloured markings identifyng
the terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked E
or
or coloured Green or Green & Yellow.
Connect Brown wire to terminal marked L or
coloured Red.
Connect Blue wire to terminal marked N or
coloured Black.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
If a 13 amp plug (BS 1363) is used it must be fitted
with a
The first wash cycle
GB
13 amp fuse, either in the plug or adaptor or at the
distribution board.
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
If you are in any doubt the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE
BROWN
GREEN & YELLOW
NEUTRAL (N)
LIVE (L)
EARTH (E)
Disposing of the appliance:
When disposing of the appliance please remove
the plug by cutting the mains cable as close as
possible to the plug body and dispose of it as
described above.
GREEN &
YELLOW
13 ampere fuse
BROWN
CROSS-BAR
CORD GRIP
BLUE
! The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
! When the washing machine is installed, the mains
socket must be within easy reach.
! Do not use extensions or multiple sockets.
! The power supply cable must never be bent or
dangerously compressed.
! The power supply cable must only be replaced by
an authorised serviceman.
Warning! The company denies all liability if and
when these norms are not respected.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
Technical details
Model
BWD 129
59.5 cm wide
81,5 cm high
54 cm deep
Dimensions
from 1 to 5 kg for the wash
programme; from 1 to 4 kg for the
drying programme
Capacity
Electric
connections
voltage 230/240 Volts 50 Hz maximum
absorbed power 2050 W
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 46 litres
Water
connections
Spin speed
up to 1200 rpm
Wash: programme C; temperature
60°C; run with a load of 5 kg.
Control
Drying: first drying cycle performed
with a 1 kg load, by selecting a drying
time of 40 min;
programmes
according to
IEC456 directive
Second drying cycle performed with a 4
kg load and the DRYING PROGRAMME
knob on the "Extra dry" setting.
This appliance is compliant with the
following European Community Directives:
- 73/23/CEE of 19/02/73 (Low Voltage)
and subsequent amendments
- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments
- 2002/96/CE
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions for the fitter
Door Mounting Accessories (Fig. 1-2-3-4-5).
GB
Mounting the wooden panel onto the door and
inserting the machine into cabinets:
In the case where the machine must be shipped for
final installation after the wooden panel has been
mounted, we suggest leaving it in its original
packaging. The packaging was designed to make it
possible to mount the wooden panel onto the machine
without removing it completely (see figures below).
The wooden panel that covers the face of the machine
must not be less than 18 mm in thickness and can be
hinged on either the right or left. For the sake of
practicality when using the machine, we recommend
that the panel be hinged on the same side as the door
for the machine itself - the left.
N° 2 Hinge Supports
Fig. 1
N° 2 Hinges
Fig. 2
N° 1 Magnet
N° 1 Magnet plate
Fig. 4
Fig. 3
A
B
N° 1 Rubber plug
Fig. 5
N° 1 Spacer
Fig. 4/B
- No. 6 type A self-threading screws, l =13 mm.
- No. 2 type B metric, countersunk screws, l =25; for
fastening the magnet plate to the cabinet.
- No. 4 type C metric screws, l =15 mm; for mounting
C
D
the hinge supports to the cabinet.
- No. 4 type D metric screws, l =7 mm; for mounting the
hinges on the supports.
Mounting the Parts onto the Face of the Machine.
- Mount the hinge supports onto the face of the
machine, positioning the hole indicated by the arrow in
fig. 1 towards the inside of the face and using the type
C screws.
- Mount the magnetic plate on the opposite side, at
the top, using the two type B screws.
e
it
e
s
r
u
T
- Place the spacer illustrated in fig. 4/B between the
appliance front and the magnet receiver.
E
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Drilling Template.
GB
- To trace the positions of the holes on the left-hand
side of the panel, align the drilling template to the top
left side of the panel using the lines traced on the
extremities as a reference.
- To trace the positions of the holes on the right-hand
side of the panel, align the drilling template to the top
right side of the panel.
- Use an appropriately sized router to mill the holes
for the two hinges, the rubber plug and the magnet.
Fig.
8Fig.
9
Mounding the Parts onto the Wooden Panel (Door).
- Insert the hinges into the holes (the movable part of
the hinge must be positioned facing away from the
panel) and fasten them with the 4 type A screws.
- Insert the magnet into the top hole on the opposite side
of the hinges and fasten it with the two type B screws.
- Insert the rubber plug into the bottom hole.
Accessories provided for the height adjustment.
The following can be found inside the polystyrene lid
(fig. 10): 2 crossbars (G), 1 strip (M)
the following can be found
inside the appliance drum:
4 additional feet (H),
4 screws (I),
The panel is now ready to be mounted onto the machine.
4 screws (R),
4 nuts (L),
Mounting the Panel into the machine.
2 plinth guides (Q)
Insert the nib of the hinge (indicated by the arrow in
fig. 2) into the hole for the hinge and push the panel
towards the front of the machine. Fasten the two
hinges with the type D screws.
Fig. 10
Adjusting the appliance height.
The height of the appliance can be adjusted (from 815 mm to 835
mm), by turning the 4 feet.
Fastening the plinth guide.
If the machine is installed at the end of a set of modular
cabinets, mount either one or both of the guides for
the base molding (as shown in fig. 8). Adjust them for
depth based on the position of the base molding, and,
if necessary, fasten the base to the guides (fig. 9).
This is how to assemble the plinth guide (fig. 8):
Fasten angle P using screw R, insert plinth guide Q into
the special slot and once it is in the desired position,
lock it in place using angle P and screw R.
Should you require the appliance to be placed higher than the
above height, you need to use the following accessories to raise
it to up to 870 mm:
the two crossbars (G); the 4 feet (H); the 4 screws (I); the 4 nuts
(L) then perform the following operations (fig. 11):
remove the 4 original feet, place a crossbar G at the front of the
appliance, fastening it in place using screws I (screwing them in
where the original feet were) then insert the new feet H.
Repeat the same operation at the back of the appliance.
Now adjust feet H to raise or lower the appliance from 835 mm to
870mm.
Inserting the machine into the Cabinet.
- Push the machine into the opening, aligning it with
the cabinets (fig. 6).
Once you have reached the desired height, lock nuts L onto
crossbar G.
- Regulate the adjustable feet to raise the machine to
the appropriate height.
To adjust the appliance to a height between 870 mm and 900 mm,
you need to mount strip M, adjusting feet H to the required
height.
- To adjust the position of the wooden panel in both
the vertical and horizontal directions, use the C and D
screws, as shown in fig. 7.
Insert the strip as follows:
Important: close the lower part of the appliance front
by ensuring that the plinth rests against the floor.
loosen the three screws N situated at the front of the Top cover
of the appliance, insert strip M as shown in fig. 12, then fasten
screws N.
600 min
M
C
595
540
G
D
in
m
570
C
L
H
I
Fig. 6
Fig. 7
Fig. 11
Fig. 12
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Washer-dryer description
Control panel
FUNCTION
Buttons
GB
ON/OFF
Button
Leds
Detergent dispenser
DOOR LOCKED
Led
START/
RESET
Button
M
PROGRAMME
Knob
DRYING
PROGRAMME
Knob
VARIABLE
TEMPERATURE
Knob
Detergent dispenser: to add detergent and
fabric softener (see page 12).
ON/OFF button: to turn the Washer-dryer on and
off.
LEDS: to find out which wash cycle phase is under way.
If the Delay Start function has been set, the time
left until the programme starts will be indicated
(see page 9).
START/RESET button: to start the programmes
or cancel any incorrect settings.
DOOR LOCKED Led: to find out whether the
Washer-dryer is on and if the appliance door can
be opened (see page 9).
DRYING PROGRAMME knob: to set the desired
drying cycle (see page 11).
PROGRAMME knob: to select the wash
programmes. The retractable control knob: press
the centre of the knob for it to pop out. The knob
stays still during the cycle.
FUNCTION buttons: to select the functions
available. The button corresponding to the
function selected will remain on.
VARIABLE TEMPERATURE knob: to set the tem-
perature or the cold wash cycle (see page 11).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Leds
Cycle phase under way:
During the wash cycle, the LEDs gradually illumi-
nate on to indicate the cycle phase under way:
GB
The LEDS provide important information.
This is what they can tell you:
Prewash/Wash
Rinse
Delay set:
If the Delay Start function has been enabled (see
page. 11), once you have started the programme,
the LED corresponding to the delay set will begin
to flash:
Spin
Drying
Wash
2hr
Note:
- during draining, the LED corresponding to the
Spin cycle phase will be turned on.
Rinse
4hr
Spin
6hr
Drying
9hr
- when the drying cycle is complete, the indicator light
relative to phase will flash, to indicate that the
DRYING PROGRAMME knob needs to be set back to
the “¡” setting.
As time passes, the remaining delay will be
displayed, and the corresponding LED will flash:
Function buttons
Wash
2hr
The FUNCTION BUTTONS also act like LEDS.
When a function is selected, the corresponding
button is illuminated.
Rinse
4hr
Spin
6hr
If the function selected is incompatible with the
programme set, the button will flash and the
function will not be enabled.
Drying
9hr
Once the set delay is complete, the flashing LED
will turn off and the programme set will start.
If you set a function that is incompatible with
another function you selected previously, only the
last one selected will be enabled.
DOOR LOCKED led:
If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any
damages, wait for the LED to flash before you open the appliance door.
! The rapid flashing of the DOOR LOCKED Led together with the flashing of at least one other LED
indicates there is an abnormality. Call for Technical Assistance (see page 15).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting and Programmes
5. Set the drying cycle if necessary (see page 11).
6. Add the detergent and any fabric softener (see
page 12).
7. Start he programme by pressing the START/RESET
button. To cancel it, keep the START/RESET button
pressed for at least 2 seconds.
8. When the programme is finished, the DOOR
LOCKED Led will flash to indicate that the
appliance door can be opened. Take out your
laundry and leave the appliance door ajar to
allow the drum to dry thoroughly. Turn the
Briefly: starting a programme
GB
1. Switch the Washer-dryer on by pressing
button . All the LEDS will light up for a few
seconds and the DOOR LOCKED Led will
begin to flash.
2. Load your laundry into the washing machine and
shut the appliance door.
3. Set the PROGRAMME knob to the
programme required.
4. Set the wash temperature (see page 11).
Washer-dryer off by pressing button
.
Programme table
Cycle
length
(minutes)
Detergent
Program- Wa sh
Drying
Fabric
softener
Type of fabric and degree of soil
Description of wash cycle
mes
temp. Cycle
Pre-
Wash
wash
Cottons
Extremely soiled whites
(sheets, tablecloths, etc.)
Pre-wash, wash cycle, rinse cycles,
intermediate and final spin cycles
A
B
C
D
90°C
90°C
60°C
40°C
137
120
105
72
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Extremely soiled whites
(sheets, tablecloths, etc.)
Wash cycle, rinse cycles,
intermediate and final spin cycles
Heavily soiled whites and fast
colours
Wash cycle, rinse cycles,
intermediate and final spin cycles
Slightly soiled whites and delicate
colours (shirts, jumpers, etc.)
Wash cycle, rinse cycles,
intermediate and final spin cycles
Drying cycle for cotton fabrics
Synthetics
Heavily soiled fast colours
(baby linen, etc.)
Wash cycle, rinse cycles, anti-crease
or delicate spin cycle
E
E
F
G
H
60°C
40°C
50°C
40°C
30°C
77
62
73
58
30
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Fast colours (all types of
slightly soiled garments)
Wash cycle, rinse cycles, anti-crease
or delicate spin cycle
Heavily soiled fast colours
(baby linen, etc.)
Wash cycle, rinse cycles, anti-crease
or delicate spin cycle
Delicate colours (all types of
slightly soiled garments)
Wash cycle, rinse cycles, anti-crease
or delicate spin cycle
Delicate colours (all types of
slightly soiled garments)
Wash cycle, rinse cycles and delicate
spin cycl
Drying cycle for synthetic
fabrics
Delicates
Wash cycle, rinse cycles and delicate
spin cycle
J
L
Wool
40°C
30°C
50
45
•
•
•
•
•
•
Very delicate fabrics
(curtains, silk, viscose, etc.)
Wash cycle, rinse cycles, anti-crease
or draining cycle
Drying cycle for delicate fabrics
PARTIAL PROGRAMMES
Light Rinses
Spins
Light Rinses
Spins
Rinse cycles, anti-crease or draining
Draining and delicate spin cycle
Draining
•
•
•
Draining
Notes
For the Anti-crease function, please see page 12. The information contained in the table is purely indicative.
Special programme
Daily 30' (programme “H” for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it
only lasts 30 minutes and allows you to save on both time and energy. By setting this programme (“H” at 30°C),
you can wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Personalisations
Setting the temperature (Variable Temperature )
Turn the VARIABLE TEMPERATURE knob to set the wash temperature (see Programme table on page 10).
The temperature can be lowered, or even set to a cold wash (Cold).
GB
The data contained in the
table are purely indicative.
Table of drying times
Set the drying cycle (Drying Programme)
Turn the DRYING PROGRAMME knob to set the desired
drying type. Two options are available:
Fabric
type
Load type
Max.
load
(kg)
Extra
dry
Hanger
Dry
Iron
Dry
A - Based on time: From 40 minutes to 150.
Cotton,
Linen
Clothing of different
sizes
4
4
130
130
90
120
120
80
110
110
70
B - Based on the damp level of the dry clothes:
Iron Dry: slightly damp clothes, easy to iron.
Hanger Dry : dry clothes to put away.
Extra dry: very dry clothes, recommended for
towelling and bathrobes.
Cotton
Terry towels
Terital,
Cotton
Sheets, Shirts
2,5
Acrylics
Nylon
Pyjamas, socks, etc.
1
1
6
6
5
5
6
0
0
6
6
A cooling stage is foreseen at the end of the drying cycle.
Slips, tights, stockings, etc.
6
If your laundry load to wash and dry is exceptionally in
excess of the maximum load foreseen (see table opposite), perform the wash cycle, and when the programme is
complete, divide up the garments and put part of them back in the drum. Now follow the instructions provided
for a dry only cycle. Repeat this procedure for the remainder of the load.
Dry only
Turn the PROGRAMME knob to one of the drying settings
the desired drying type using the DRYING PROGRAMME knob.
depending on the type of fabric, then select
Important: - A spin cycle is carried out during the drying if you have set a cotton programme and a level of
dryness (Extra dry, Hanger Dry, Iron Dry).
- The woollen garments drying cycle should only and exclusively be run together with the selection of a
specific cycle time (150 - 100 - 60 - 40 minutes). We recommend a 60 minute drying cycle for a 1 kg load.
If one of the three levels (Extra dry, Hanger Dry, Iron Dry) is selected by mistake, the appliance will run a
drying cycle lasting the MAX time foreseen (150 minutes).
- For cotton loads of less than 1 Kg, use the drying programme designed for synthetic fabrics.
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the programme set.
Enabled with
programmes:
Function
Effect
Comments
Press the button repeatedly until the LED corresponding to the
desired delay is turned on.
The fifth time the button is pressed, the function will be disabled.
N.B.: Once you have pressed the Start/Reset button, the delay
can only be decreased if you wish to modify it.
Delays the start
of the wash by
up to 9 hours.
All
Delay
Start
Allows for an
impeccable wash,
visibly whiter
than a standard
Class A wash.
A, B, C, D,
E, F, G
This function is incompatible with the QUICK WASH function.
Super
Wash
Cuts the duration
of the wash cycle This function is incompatible with the SUPER WASH function.
by 30%.
A, B, C, D,
E, F, G
Quick
Wash
All
programmes
except for L
and draining.
Reduces the spin
speed.
1200
600
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergents and laundry
Detergent dispenser
Special items
GB
Good washing results also depend on the correct
dose of detergent: adding too much detergent
won't necessarily make for a more efficient wash,
and may in fact cause build up on the interior of
your appliance and even pollute the environment.
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme
“L” which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out
and load a maximum of 2-3 kg, repeating the rinse
cycle once or twice and using the delicate spin
cycle.
Open up the detergent
dispenser and pour in
the detergent and
fabric softener, as
follows.
Trainers: remove any mud. They can be washed
together with jeans and other tough garments,
but not with whites.
1
2
3
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1 kg.
Woolmark Platinum Care
compartment 1: Detergent for pre-wash
(powder)
As gentle as a hand wash.
Hotpoint is the only washer-dryer to have
obtained the prestigious Woolmark
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in
immediately prior to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.
Platinum Care mark of recognition (M.0303) from
The Woolmark Company, which certifies the
machine washing of all woollen garments, even
those whose label states "hand wash only"
(1 kg max.). The "Wool" programme therefore
offers you complete peace of mind when washing
all woollen garments, with great performance
guaranteed every time.
! Do not use hand wash detergent because it may
form too much foam.
Preparing your laundry
• Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments
from whites.
Anti-crease
This function interrupts the wash programme, and
the washing is left to soak in water before the
appliance is drained. It is enabled in programmes
E - F - G - L and “Light Rinses”.
• Empty all pockets and check for loose buttons.
• Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 5 kg
To conclude the cycle, press the START/RESET
button.
To run the draining cycle alone, set the knob to the
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1 kg
relative symbol
button.
and press the START/RESET
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and advice
! The Washer-dryer was designed and built in
not be disposed of in the normal unsorted
municipal waste stream. Old appliances must be
collected separately in order to optimise the
recovery and recycling of the materials they
contain and reduce the impact on human health
and the environment. The crossed out "wheeled
bin" symbol on the product reminds you of your
obligation, that when you dispose of the
GB
compliance with the applicable international safety
regulations. The following information is provided for
your safety and should consequently be read carefully.
General safety
• This appliance has been designed for non-
professional, household use and its functions
must not be changed.
appliance it must be separately collected.
• This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
Consumers should contact their local authority
or retailer for information concerning the
correct disposal of their old appliance.
• Never touch the washing machine when
barefoot or with wet or damp hands or feet.
• Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull
the plug out yourself.
Saving energy and respecting the
environment
Environmentally-friendly technology
• Do not open the detergent dispenser while the
appliance is in operation.
If you only see a little water through your
appliance door, this is because thanks to the
latest Hotpoint technology, your washing machine
only needs less than half the amount of water to
get the best results: an objective reached to
respect the environment.
• Do not touch the drain water as it could reach
very high temperatures.
• Never force the washing machine door: this
could damage the safety lock mechanism
designed to prevent any accidental openings.
• In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
Saving on detergent, water, energy and time
• To avoid wasting resources, the Washer-dryer
should be used with a full load. A full
• Always keep children well away from the
appliance while in operation.
load instead of two half loads allows you to save
up to 50% on energy.
• The appliance door tends to get quite hot during
the wash cycle.
• The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save
on detergent, time, water and between 5 and
15% energy.
• Should it have to be moved, proceed with the
help of two or three people and handle it with
the utmost care. Never try to do this alone,
because the appliance is very heavy.
• Before loading your laundry into the washing
machine, make sure the drum is empty.
• During the drying phase, the door tends to get
quite hot.
• Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on energy.
• Use the correct quantity of detergent
depending on the water hardness, how soiled
the garments are and the amount of laundry
you have, to avoid wastage and to protect the
environment: despite being biodegradable,
detergents do contain ingredients that alter
the natural balance of the environment. In
addition, avoid using fabric softener as much as
possible.
• Do not use the appliance to dry clothes that
have been washed with flammable solvents (e.g.
trichlorethylene).
• Do not use the appliance to dry foam rubber or
similar elastomers.
• Make sure that the water tap is turned on
during the drying cycles.
• This washer-dryer can only be used to dry
clothes which have been pre-washed in water.
• If you use your washing machine from late in the
afternoon until the early hours of the morning,
you will help reduce the electricity board's peak
load. The Delay Start function (see page 11)
helps to organise your wash cycles accordingly.
• If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
Disposal
• Disposing of the packaging material:
observe local regulations, so the packaging can
be re-used.
• The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires
that old household electrical appliances must
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and maintenance
Cutting off the water or electricity
supply
GB
•
Turn off the water tap after every wash. This
will limit the wear of your appliance's water
system and also prevent leaks.
•
Unplug your appliance when cleaning it and
during all maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser
by raising it and pulling
1
it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
2
Caring for your appliance door and drum
•
Always leave the appliance door ajar to prevent
unpleasant odours from forming.
Cleaning the pump
The Washer-dryer is fitted with a self-cleaning
pump that does not require any maintenance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during
the wash cycles, water pressure is very strong
and a cracked hose could easily split open.
! Never use hoses that have already been used.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Your Washer-dryer could fail to work. Before calling for Assistance (see page 17), make sure the problem can't
easily be solved by consulting the following list.
GB
Possible causes/Solution:
• The appliance is not plugged into the socket, or not enough to make contact.
• There has been a power failure.
Problem
The Washer-dryer won't start.
• The appliance door is not shut properly.
• The
The wash cycle won't start.
button has not been pressed.
• The START/RESET button has not been pressed.
• The water tap is not turned on.
• A delayed start has been set (using the Delay Start, see page 11).
• The water inlet hose is not connected to the tap.
• The hose is bent.
The Washer-dryer fails to load
water.
• The water tap is not turned on.
• There is a water shortage.
• The water pressure is insufficient.
• The START/RESET button has not been pressed.
• The drain hose is not fitted between 65 and 100 cm from the floor (see page 3).
• The free end of the hose is underwater (see page 3).
The Washer-dryer continuously
loads and unloads water.
• The wall drainage system doesn't have a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and call for Assistance. If the dwelling is on one of the upper
floors of a building, there may be drain trap problems causing the Washer-dryer
to load and unload water continuously. In order to avoid such an inconvenience,
special anti-drain trap valves are available in shops.
• The programme does not foresee the draining: some
programmes require enabling the draining manually (see page 10).
• The Anti-crease function is enabled: to complete the programme,
press the START/RESET button (see page 11).
• The drain hose is bent (see page 3).
The Washer-dryer does not drain
or spin.
• The drain duct is clogged.
• The drum was not unblocked correctly during installation (see page 2).
• The Washer-dryer is not level (see page 2).
The Washer-dryer vibrates too
much during the spin cycle.
• The Washer-dryer is closed in between furniture cabinets and
the wall (see page 2).
• The water inlet hose is not screwed on correctly (see page 2).
• The detergent dispenser is obstructed (to clean it, see page 14).
• The drain hose is not secured properly (see page 3).
The Washer-dryer leaks.
• This means there is a problem with the machine. Before calling
Assistance, please follow the set of instructions below:
1. Switch off the machine; 2. Remove the plug connecting the
appliance to the mains supply and wait for at least 40 seconds.;
3. Place the plug back into the socket; 4. Switch on the machine;
5. If the problem is still evident after this process has been carried out,
contact Assistance.
The DOOR LOCKED Led flashes
rapidly at the same time as at
least one other LED.
There is too much foam.
• The detergent is not suitable for machine washing (it should bear the
definition "for washing machines" or "hand and machine wash", or the like).
• You used too much detergent.
The washer-dryer does not dry.
• The appliance is not plugged into the socket, or not enough to make contact.
• There has been a power failure.
• The appliance door is not shut properly.
• A delayed start has been set (using the Delay Start, see page 11).
• the DRYING PROGRAMME knob is on the “¡” setting.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
12 Months Parts and Labour Guarantee
GB
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of
breakdown repairs for twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective
because of either workmanship or materials, we will, at our discretion, either repair or replace the
appliance at no cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our
operating and maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise
interfered with by any person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result
of improper installation.
Replacement of any consumable item or accessory . These include but are not limited to: plugs,
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-
DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on
you registering your appliance with us and the parts being fitted by one of our authorised
engineers. There will be a charge for our engineer's time. To activate the extra parts warranty on
your appliance, simply call our registration line on 0870 6092094 (ROI 01 230 0800).
Extended Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the
expense of repair bills for the life of your policy. To find the ideal plan for you please call our advice
line on 08709 088 088 (ROI 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint
Service Hotline on 08709 066 066 (ROI 0818 313 413) for telephone assistance, or, where
necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will
replace your machine or, if you prefer, give you your money back.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
After Sales Service
No one is better placed to care for your Hotpoint appliance during the course of its working life
than us - the manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in Europe offering you access to 400 skilled telephone advisors
and 1100 fully qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08709 066 066
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08709 077 077
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts
guarantee you must register your appliance with us.
UK: 0870 6092094
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to
use quality, recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,
remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts
separately to ensure that the appliance can no longer be plugged into a mains socket, and the door
cannot be locked shut.
February 2006
195.044.614.04
Download from Www.Somanuals.com. All Manuals Search And Download.
|