Instructions for
installation and use
WASHING MACHINE
Contents
EN
Installation, 2-3-4-5
Unpacking and levelling
EN
Connecting the electricity and water supplies
Technical data
English,1
Description of the machine, 6-7
Control panel
Auto Dose System, 8-9
Running a wash cycle, 10
Wash cycles and options, 11
Table of wash cycles
Wash options
Detergents and laundry, 12
Detergent
Preparing the laundry
AQUALTIS
Washing recommendations
Load balancing system
AQLF9F 49 U
Precautions and advice, 13
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 14
Cutting off the water and electricity supplies
Cleaning the machine
Cleaning the detergent dispenser drawer
Caring for your appliance drum
Cleaning the pump
Checking the water inlet hose
Trouble shooting, 15-16-17
Assistance, 18-19
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the drain hose
• the supply voltage is included within the values i
EN
ndicated on the Technical details table (see page 5);
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from the
floor;
• the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
65 - 100 cm
Your appliance is now supplied with a 13 amp fused plug
it can be plugged into a 13 amp socket for immediate
use. Before using the appliance please read the
instructions below.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
The drain hose may be
connected to an under-
sink trap. Before
connecting the drain
hose from the machine
ensure that any blanks
or removable ends have
been taken off the
spigot.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved
fuse to BS 1362 should always be used, and the fuse
cover re-fitted. If the fuse cover is lost, the plug must not
be used until a replacement is obtained.
Where it connects to
the waste water pipe
cut end off spigot or
remove the blanking cap
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colour as indicated by the coloured marking or
the colour that is embossed in words on the base of the
plug. Replacements can be obtained directly from your
nearest Service Depot.
If it is place over the
edge of a basin or sink
be sure the free end of
the hose should not be
underwater.
Removing the plug:
If your appliance has a non-rewireable moulded plug and
you should wish to re-route the mains cable through
partitions, units etc., please ensure that either:
the plug is replaced by a fused 13 ampere rewireable
plug bearing the BSI mark of approval.
or:
! We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with BS
5733) which is accessible without moving the appliance.
Ensure that if the drain hose is pushed into a
standpipe, that the end does not go down more than
15cms (6 inches). If the hose is pushed down too far,
this may cause the machine to self -syphon ie.
continuously empty as it is filling.
Disposing of the plug:
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally
inserted into a socket.
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Electric connection
Before plugging the appliance into the mains socket,
make sure that:
Green & Yellow Earth
Blue
Neutral
Live
Brown
• the socket is earthed and in compliance with the
applicable law;
• the socket is able to sustain the appliance's
maximum power load indicated in the Technical details
table (see page 5);
3
Download from Www.Somanuals.com. All Manuals Search And Download.
As the colours of the wires in the lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked E or
or coloured Green or Green & Yellow.
Connect Brown wire to terminal marked L or coloured
Red.
EN
Connect Blue wire to terminal marked N or coloured
Black.
If a 13 amp plug (BS 1363) is used it must be fitted with
a
13 amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance
with the following code:
BLUE
NEUTRAL (N)
LIVE (L)
BROWN
GREEN & YELLOW
EARTH (E)
GREEN &
YELLOW
13 ampere fuse
BROWN
BLUE
CROSS-BAR
CORD GRIP
Disposing of the appliance:
When disposing of the appliance please remove the plug
by cutting the mains cable as close as possible to the
plug body and dispose of it as described above.
! The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to leave it
exposed to rain and thunderstorms.
! When the washing machine is installed, the mains
socket must be within easy reach.
! Do not use extensions or multiple sockets.
! The power supply cable must never be bent or
dangerously compressed.
! The power supply cable must only be replaced by an
authorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Technical data
Model
AQLF9F 49 U
width 59.5 cm
height 85 cm
depth 64,5 cm
Dimensions
Capacity
from 1 to 9 kg
Electrical
please refer to the technical data
plate fixed to the machine
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 62 litres
Water connections
Spin speed
up to 1400 rotations per minute
Energy rated
programmes
according to
regulation
programme
and 40°C.
; temperature 60°C
2010/1061
This appliance conforms to the
following EC Directives:
- 2004/108/EC (Electromagnetic
Compatibility)
- 2006/95/EC (Low Voltage)
- 2002/96/EC
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the machine
CONTROL
PANEL
EN
PORTHOLE DOOR
PORTHOLE DOOR
HANDLE
KICK STRIP
ADJUSTABLE FEET
PORTHOLE DOOR
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
Always use the handle to
open the porthole door (see
figure).
activity is detected. Press the ON-OFF
button briefly
and wait for the machine to start up again.
DETERGENT DISPENSER DRAWER
The detergent dispenser
drawer is located inside the
machine and can be
accessed by opening the
door.
Refer to the chapter "Auto
Dose System" for information
on operation.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TEMPERATURE/
DETERGENT
display
Control panel
DELAY TIMER/SOFTENER /
CYCLE DURATION display
EN
WASH
CYCLE
PHASE
icons
SPIN display
DETERGENT
DILUTION
button
SOFTENER
button
ECO indicator light
START/PAUSE
button with indicator
DETERGENT
button
OPTION button
with indicator light
WASH CYCLE
SELECTOR knob
light
CHILD LOCK button
ON/OFF button with
DELAY
TIMER
TEMPERATURE button
with indicator light
indicator light
DOOR LOCKED
button
indicator light
SPIN SPEED
button
WASH CYCLE PHASE icons: these illuminate to
Button with
ON/OFF indicator light: press this briefly
indicate the progress of the wash cycle (Wash
–
to switch the machine on or off. The green indicator light
indicates that the machine is switched on. To switch off
the washing machine during the wash cycle, press and
hold the button for approximately 3 seconds; if the
button is pressed briefly or accidentally the machine will
not switch off. If the machine is switched off during a
wash cycle, this wash cycle will be cancelled.
Rinse
– Spin
– Drain
).
The text
lights up when the cycle is complete.
START/PAUSE button with indicator light: when the
green indicator light flashes slowly, press the button to
start a wash cycle. Once the cycle has begun the
indicator light will remain lit in a fixed manner. To pause
the wash cycle, press the button again; the indicator
light will flash in an orange colour. If the “Door locked”
indicator light is switched off, the door may be
WASH CYCLE SELECTOR knob: may be turned in
either direction. To select the most suitable wash cycle,
please refer to the “Table of wash cycles”.
opened. To start the wash cycle from the point at which
it was interrupted, press the button again.
The knob will not move during the wash cycle.
TEMPERATURE
button: press to modify or exclude
DOOR LOCKED
indicator light: indicates that the
the temperature setting; the value selected will appear
porthole door is locked. To open the door, pause the
on the display above (see “Running a wash cycle”).
wash cycle (see “Running a wash cycle”).
SPIN SPEED CYCLE
button: press to modify or
CHILD LOCK
button with indicator light: to activate
exclude the spin cycle; the value selected will appear on
or deactivate the CHILD LOCK, press and hold the
button for approximately 2 seconds. when the indicator
light is illuminated, the control panel is locked. This
means it is possible to prevent wash cycles from being
modified accidentally, especially where there are children
in the home.
the display above (see “Running a wash cycle”).
DELAY TIMER
button: press to set a DELAY TIMER
for the selected wash cycle; the set delay time will appear
on the display above (see “Running a wash cycle”).
DETERGENT and
SOFTENER buttons: refer to
"Modifying pre-set parameters" in the chapter "Auto Dose
System".
ECO indicator light: the
icon lights up when, after
altering the washing parameters, an energy saving of at
least 10% is made. Furthermore, before the machine
enters “Standby” mode, the icon will light up for a few
seconds; when the machine is switched off the
DETERGENT DILUTION button: refer to "Filling the
tanks" in the chapter "Auto Dose System".
OPTION button with indicator light: press to select the
available options. The indicator light corresponding to the
selected option will remain lit (see “Running a wash cycle”).
estimated energy saving will be around the 80% mark.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Dose System
Introduction
Filling the tanks:
EN
This washing machine is
Open the detergent dispenser drawer in the "Auto Dose
System" mode (refer to "Detergent dispenser").
Slowly pour the detergent (B) and fabric softener (C)
until the tanks are completely filled (see picture).
equipped with two tanks: one
for liquid detergent (either
concentrated or diluted) with
a capacity of approx. 5.5 l
and another for liquid fabric
softener (either concentrated
or diluted) with a capacity of
approx. 3.5 l (see picture).
! Check the detergent/fabric
softener box to verify whether
it is diluted or concentrated
detergent. The automatic
dosing system intakes the
C
B
correct amount of detergent and fabric softener from the
tanks for each type of load and at the right time,
guaranteeing optimal washing results without wastage.
The amount of detergent/fabric softener can be modified
manually by pressing the DETERGENT and FABRIC
SOFTENER buttons (refer to "Modifying pre-set
To avoid exceeding the maximum capacity, a buzzer (beep)
will sound with growing intensity to signal the level and 3
long beeps will sound once the tank is completely full.
Start the wash cycle immediately after filling the tanks to
ensure that the dispenser is properly cleaned.The
parameters"). If you prefer, the washing machine can
also be used in the "traditional" mode, i.e. by adding the
detergent in the dispenser; the machine will automatically
detect the detergent and will not use the tanks.
respective icons
(for the detergent) and
(for the
fabric softener) will light up gradually to signal the level.
Detergent dispenser
"Traditional" mode.
Pull out the detergent dispenser drawer up to the first
stop point to add the detergent (either liquid or powder
detergent), bleach or other additives (e.g. whiteners) and
the pre-wash detergent for washing in the "traditional"
mode (refer to "Traditional” mode).
The filling time depends on the density of the product.
Very dense products will take longer to fill.
"Auto Dose System” mode.
In order to fill the detergent
and fabric softener tanks,
Close the detergent dispenser drawer only once the
compartments are completely empty.
A
the detergent dispenser
drawer must be fully
extracted: open the dispenser
Select the density of the detergent added (either
concentrated or liquid) by pressing the appropriate
button
.
drawer up to the first stop
point then press the lever (A)
The machine will store the selection.
If no option is selected, the detergent intake option will
be pre-set to "diluted".
and open up to the second
stop point, making sure that
it is fully extracted. Avoid
Use button to set the amount of fabric softener that
will be automatically extracted by the machine:
moving the dispenser drawer during filling operations.
Once the tanks have been filled (refer to "Filling the tanks"),
the machine can run up to 40 cycles before the detergent
finishes (*).
1) If concentrated softener is used, we recommend
selecting the first level ( with one bar) and, if
necessary, stepping up by a single position ( with 2
bars) to increase detergent intake.
First-time use
2) If diluted softener is used, we recommend setting level
Turn the washing machine on by pressing the ON/OFF
button. The first wash cycle must be carried out without
laundry and by adding detergent in the detergent
dispenser (refer to "Traditional” mode); set the
programme " " (Cotton 90°) without pre-wash and
without filling the tanks.
3 ( with 3 bars) and to then either increase/decrease
the amount of fabric softener to be extracted.
3) To exclude the use of fabric softener, press
until
the bars disappear (also refer to "Modifying pre-set
parameters").
(*) with an average load of 4 kg, 40°C Cotton programme, "medium" water
hardness level and dirt level set to 3.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Signals for successive refilling:
Automatic cleaning:
EN
When the level of detergent/fabric softener falls below the
required level, at the end of the cycle, the first segment of
The washing machine carries out an automatic cleaning
cycle during the rinse cycle if the level of detergent that
remains is insufficient for carrying out a
successive wash cycle.
the detergent symbol or the petal of the
fabric
softener symbol in the bottom left section, will flash slowly
on the display. Once the detergent/fabric softener is
finished, the first segment of the detergent symbol or the
Cleaning cycle set by the user:
Run the cleaning cycle (with empty drum) if you require
adding a different product to the previous one or if the tanks
have been incorrectly filled (e.g. fabric softener has been
erroneously poured into the detergent tank or vice-versa).
petal of the
fabric softener symbol in the lower left
section will flash fast to signal that the detergent or fabric
softener tank is empty. While the cycle runs, with empty
tanks, the
cycle or during the pause mode, the first segment of the
symbol and the petal of the symbol in the lower left
symbols will disappear; at the end of the
Press button
cleaning of the detergent tank, button
fabric softener tank or button for cleaning both tanks.
Once the buzzers with growing intensity are followed by 2
long buzzers and the icons for the detergent, for the
fabric softener, for both tanks appear, the cleaning cycle
and hold for approximately 8 sec. to activate
for cleaning the
section will flash fast. If the tanks are not filled, the
successive wash cycles in Auto Dose System will be
carried out without any intake of detergent.
! We suggest adding detergent and fabric softener ONLY
after the machine's signal.
for the selected container will start.
The cleaning cycle lasts about 40' if the tanks are initially
empty; if not, the cycle will last longer.
! NEVER mix two different detergents; always clean out
the tank before adding a new type of detergent (refer to
"Cleaning cycle set by the user").
! During the tank cleaning cycle, the symbol will fill
gradually from bottom to top and the
gradually petal by petal.
symbol will fill
Using the "Auto Dose System"
If the compartments have been filled with detergent and
fabric softener, you may start using the machine (refer to
"Running a wash cycle").
"Traditional" mode
Pull out the detergent dispenser drawer up to the first
stop point (see picture) then pour the amount of
detergent and other additives (e.g. bleach) required for a
single wash cycle directly into the dispenser.
1. pre-wash compartment:
Powder detergents for pre-washing and powder additives
may only be used in the traditional mode or using the "Auto
Dose System", by placing the additives directly inside the
drum, preferably in conjunction with the "laundry ball".
use powder detergent only.
1
Modifying pre-set parameters:
2. main wash
compartment: use powder
The machine automatically intakes detergent on the
basis of the selected programme, wash load and water
hardness. However, the amount of detergent/fabric
softener used may be modified.
3
or liquid detergent. If the
2
latter is used, we
recommend pouring it into
the dispenser immediately
button: press to increase, decrease and to exclude
detergent intake.
before starting the washing
machine and without
running a pre-wash cycle.
3. ! Do not pour anything in this compartment.
Tablet detergent or the relative "laundry ball" must be
added directly inside the drum. In this event, deactivate
button: press to increase, decrease and to exclude
fabric softener intake.
the "Auto Dose System" (by pressing the
button until
the relative vertical bars disappear from the display).
Do not pour any fabric softener as the appropriate
quantity required for each wash cycle will be
automatically extracted.
The level of detergent/fabric softener suggested by the
machine is indicated by 3 bars.
To deactivate fabric softener intake, press the
until the vertical bars disappear from the display.
For wool and silk garments, we recommend using a
special detergent which must be poured directly into the
detergent dispenser (compartment 2).
button
Less than 3 bars indicates a lower level of detergent/
fabric softener compared to that suggested by the
machine, while more than 3 bars indicates a higher level
of detergent/fabric softener.
Cleaning the tanks:
Running the wash cycle:
Select the programme and the compatible options on
the basis of the required need and type of load.
Tank cleaning cycles can either be automatic or pre-set
by the user.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Running a wash cycle
WARNING: before you use the washing machine for
the first time, run a wash cycle with detergent and no
laundry, using the 90° cottons cycle without pre-wash.
press the button until the display shows the text OFF;
the symbol will disappear.
EN
! Once the START/PAUSE button has been pressed,
the time delay may only be decreased.
1. SWITCH THE MACHINE ON. Press the
All the indicator lights will illuminate for 1 second; the
indicator light corresponding to the button will then
button.
Modify the cycle settings.
Press the OPTION button to customise the wash
cycle in accordance with your own requirements.
remain lit in a fixed manner and the START/PAUSE
indicator light will flash slowly.
• Press the button to activate the option; the
corresponding indicator light will switch on.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed the
maximum load value indicated in the table of wash
cycles on the following page.
• Press the button again to disable the option; the
indicator light will switch off.
! If the selected option is not compatible with the
selected wash cycle, this incompatibility will be
signalled by the flashing of the indicator light and a
sound alert (3 beeps); the option will not be activated.
3. MEASURE OUT THE DETERGENT. There is no
need to add detergent when the "Auto Dose System"
mode is used, as the machine automatically intakes
detergent on the basis of the selected programme,
type of load and water hardness. Refer to the
paragraph "Traditional” mode for implementing the
traditional operation mode.
7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light
remains lit in a fixed manner and the porthole door
locks (the
DOOR LOCKED indicator light
illuminates). The icons corresponding to the wash
cycle phases will light up during the cycle to indicate
which phase is currently in progress. To change a
wash cycle once it has already started, pause the
washing machine by pressing the START/PAUSE
button; then select the desired cycle and press the
START/PAUSE button again. To open the door during
a wash cycle, press the START/PAUSE button; if the
4. CLOSE THE PORTHOLE DOOR.
5. SELECT THE PROGRAMME. Turn the WASH
CYCLE SELECTOR KNOB right or left, until you have
selected the desired wash cycle. A temperature and
spin speed is set for each wash cycle; these may be
adjusted.
6. CUSTOMISE THE WASH CYCLE. Use the
DOOR LOCKED
indicator light is switched off you
relevant buttons on the control panel:
may open the door. Press the START/PAUSE button
again to restart the wash cycle from the point at
which it was interrupted.
Modify the temperature and/or spin
speed.
The machine automatically displays the maximum
temperature and spin speed values set for the
selected cycle, or the most recently-used settings if
they are compatible with the selected cycle. The
temperature can be decreased by pressing the
8. THE END OF THE WASH CYCLE. This is indicated
by the illuminated text END. The porthole door may
be opened immediately. If the START/PAUSE indicator
light is flashing, press the button to end the cycle.
Open the door, unload the laundry and switch off the
machine.
button, until the cold wash (
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
). If these buttons are pressed again, the
) setting is reached.
! If you wish to cancel a cycle which has already begun,
press and hold the
button until the cycle stops and
(
the machine switches off.
maximum values are restored.
! Exception: if the “Cotton” programme is selected,
the temperature can be increased up to a value of
90°C.
Bag for quilts, curtains and delicate garments
The Aqualtis washing machine makes it easier for you to
wash even the most valuable and delicate garments in
complete confidence thanks to the special bag which
protects the laundry (this is supplied with the machine).
We recommend that the bag is used every time you
wash quilts and padded items with an outer layer made
using synthetic material.
Set a DELAY TIMER.
Press the button until you have reached the desired
delay time. During the setting process, the delay time
is shown on the display and the
symbol flashes.
After selecting a DELAY TIMER time, the fixed
symbol and the cycle duration will appear on the
display. Press the button once to display the selected
delay time. To remove the DELAY TIMER option,
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash cycles and options
Table of wash cycles
EN
Detergent and additives
Max. Max.
temp. speed
Max.
load
(kg)
Cycle
duration
Icon Description of the wash cycle
Detergent Detergent Fabric
for prewash for wash softener
(°C)
(rpm)
Cottons wash cycles
Cotton with pre-wash
(Add detergent to the relevant compartment).
l
l
l
l
l
90°
1400
1400
9
9
60°
(Max. 90°)
Cotton (1-2): heavily soiled whites and resistant colours.
-
Cotton (2): Lightly soiled whites and delicate colours.
Coloured Cotton (3)
l
l
l
l
l
l
l
l
40°
40°
40°
40°
1400
1400
600
-
-
-
-
9
9
2
4
Shirts
Jeans
800
Special programmes
Baby: heavily soiled delicate colours
Durable Synthetics
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
40°
60°
40°
40°
60°
30°
30°
40°
800
800
800
800
1400
1200
0
-
-
-
-
-
-
-
-
4
4
Durable Synthetics (4)
4
Delicate Synthetics
4
"Bed & Bath" for bedlinen and towels.
Duvets: for down-stuffed garments.
Silk: for garments in silk and viscose, lingerie.
Wool: for wool, cashmere, etc.
9
3,5
2
800
2
Mix 30': to refresh lightly soiled garments quickly (not suitable
for wool, silk and clothes which require washing by hand)
l
l
30°
800
-
3,5
Partials wash cycles
Rinse
Spin
-
-
-
1400
1400
0
-
-
-
-
-
-
l
-
9
9
9
Drain
-
(*) Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this
value will then be shown on the display.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water
temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
For all Test Institutes:
1) Test wash cycle in compliance with regulation 2010/1061: set wash cycle
with a temperature of 60°C e 40°C.
2) Long wash cycle for cottons: set wash cycle
3) Short wash cycle for cottons: set wash cycle
with a temperature of 40°C.
with a temperature of 40°C.
4) Long wash cycle for synthetics: set wash cycle ; with a temperature of 40°C.
Eco Option
The Eco Option saves energy by not heating the water
Wash options
used to wash your laundry – an advantage both to the
environment and to your energy bill. Instead, intensified
wash action and water optimisation ensure great wash
results in the same average time of a standard cycle.
For the best washing results we recommend the usage
of a liquid detergent.
Detergent dosage
To dose the amount of detergent (refer to the chapter
"Auto Dose System").
Concentrated Detergent
To modify the degree of detergent density (refer to the
chapter "Auto Dose System").
! It cannot be used in conjunction with
,
,
,
,
,
,
,
,
,
.
Fabric softener dosage
To dose the amount of fabric softener (refer to the
chapter "Auto Dose System").
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergents and laundry
Detergent
bacteria by using a greater quantity of water and
EN
The type and quantity of detergent required depend on
the type of fabric you are washing (cotton, wool, silk,
etc.), as well as its colour, the washing temperature, the
level of soiling and the hardness of the water in the area.
Whenever the detergent and fabric softener “Auto Dose
System” is activated, this washing machine helps to
prevent wastage and to protect the environment,
besides guaranteeing optimal washing performance.
We recommend the following:
optimising the effect of special disinfecting additives
added to the detergent. At the end of the wash cycle,
the machine will slowly rotate the drum; to end the cycle
press the START/PAUSE button.
Silk: use the special “Silk”
wash cycle to wash all silk
garments. We recommend the use of special detergent
which has been designed to wash delicate clothes.
Curtains: use the “Silk” wash cycle. These should
be folded and placed inside the bag provided.
• Use powder detergent for carrying out a pre-wash
and pour in the "traditional" mode.
• Use liquid detergents for delicate cotton garments and
for all low-temperature wash cycles.
Wool: Hotpoint is the only washing machine brand to
have been awarded the prestigious Woolmark Platinum
Care endorsement (M.0508) by the Woolmark Company,
which means that all woollen garments may be washed
in the washing machine, even those which state “hand
• When activating the "Auto Dose System" mode, use
liquid detergent and fabric softeners only. Never add
ultra-concentrated detergents (e.g. "Gel" type
detergents or similar).
wash only”
on the label. The “Wool” wash cycle can
be used to wash all woollen garments in the washing
machine while guaranteeing optimum performance.
Duvets: to wash double or single duvets (the weight of
which should not exceed 3,5 kg), cushions or clothes
padded with goose down such as puffa jackets, use the
• Use gentle liquid detergents for wool and silk
garments and pour in the "traditional" mode.
! Never mix two different detergents; always clean out
the tank before adding a new type of detergent.
special “Duvets”
wash cycle. We recommend that
duvets are placed in the drum with their edges folded
inwards (see figure) and that no more than ¾ of the total
volume of the drum is used.
The detergent should be poured into the relevant
compartment - or the dispenser placed directly inside the
drum - before the wash cycle begins. In the latter case, it will
not be possible to select the Cottons with pre-wash cycle.
! Do not use hand washing detergents because these
create too much foam.
Preparing the laundry
• Shake out the garments before loading them into the
machine.
• Divide the laundry according fabric type (symbol on the
washing instruction label) and colour, making sure you
separate the coloured garments from the white ones;
• Empty all pockets and check the buttons;
• Do not exceed the values listed in the “Table of wash
cycles”, which refer to the weight of the laundry when dry.
Quilts: to wash quilts with a synthetic outer layer, use
the bag provided and set the wash cycle to “Duvets”
.
Bedlinen and towels: use the “Bed & Bath”
to wash laundry from all over the house; this optimises
cycle
How much does your laundry weigh?
1 sheet
400-500 g
150-200 g
400-500 g
900-1200 g
150-250 g
400-500 g
150-200 g
fabric softener performance and helps you save time and
energy. We recommend the use of powder detergent.
Stubborn stains: it is wise to treat stubborn stains with
solid soap before washing, and to use the Cottons with
pre-wash cycle.
1 pillowcase
1 tablecloth
1 bathrobe
1 towel
1 pair of jeans
1 shirt
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced
correctly, the machine spins at a reduced spin speed. If
the load is excessively unbalanced, the washing
machine performs the distribution process instead of
spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
Washing recommendations
Shirts: use the special “Shirts”
wash cycle to wash
shirts in different fabrics and colours to guarantee they
receive the best possible care.
Jeans: use the special “Jeans”
wash cycle for all
denim garments; turn inside out before washing and use
a liquid detergent.
Baby: use the special “Baby”
wash cycle to remove
the soiling typically caused by babies, while removing all
traces of detergent from nappies in order to prevent the
delicate skin of babies from suffering allergic reactions.
The cycle has been designed to reduce the amount of
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and tips
! The machine was designed and constructed in
accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
For more information relating to the correct disposal of
household appliances, owners should contact their
local authorities or appliance dealer.
EN
Opening the porthole door manually
General safety
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should be
supervised to ensure that they do not play with the
appliance.
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if it is
not, remove excess water
using the drain hose,
• This appliance was designed for domestic use only.
• Do not touch the machine when barefoot or with wet
or damp hands or feet.
collecting it in a bucket as
indicated in the figure.
• Do not pull on the power supply cable when
unplugging the appliance from the electricity socket.
Hold the plug and pull.
3. remove the cover panel on the lower front part of the
washing machine (see overleaf).
• Do not touch the drained water as it may reach
extremely high temperatures.
• Never force the porthole door. This could damage the
safety lock mechanism designed to prevent
accidental opening.
4. pull outwards using the
tab as indicated in the figure,
until the plastic tie-rod is
freed from its stop position;
pull downwards until you
hear a “click”, which
• If the appliance breaks down, do not under any
circumstances access the internal mechanisms in an
attempt to repair it yourself.
indicates that the door is
now unlocked.
• Always keep children well away from the appliance
while it is operating.
• If it must be moved, proceed with the help of two or
three people and handle it with the utmost care.
Never try to do this alone, because the appliance is
very heavy.
5. open the door; if this is
still not possible repeat the
procedure.
• Before loading laundry into the washing machine,
make sure the drum is empty.
Disposal
• Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
• The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states
that household appliances should not be disposed of
using the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the
materials inside the machine, while preventing
potential damage to the atmosphere and to public
health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations
regarding separated waste collection.
6. reposition the panel, making sure the hooks are
securely in place before you push it onto the appliance.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and maintenance
Cutting off the water and electricity
supplies
To access the pre-chamber:
EN
• Turn off the water tap after every wash cycle. This will
limit wear on the hydraulic system in the machine and
help to prevent leaks.
• Unplug the appliance when cleaning it and during all
maintenance work.
Cleaning the machine
1. take off the cover panel on the front of the machine
by first pressing it in the centre and then pushing
downwards on both sides until you can remove it (see
figures);
The outer parts and rubber components of the appliance
can be cleaned using a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
2. position a container so
that it will collect the water
which flows out
Cleaning the detergent dispenser drawer
(approximately 1.5 l) (see
figure);
A
D
3. unscrew the lid by
rotating it in an anti-
clockwise direction (see
figure);
4. clean the inside thoroughly;
5. screw the lid back on;
6. reposition the panel, making sure the hooks are
securely in place before you push it onto the appliance.
To pull out the dispenser drawer, open until the first stop
point then press lever A to open completely; finally, press
one of the levers D and pull the drawer outwards (see
picture).
Checking the water inlet hose
Wash it under running water; this procedure should be
effected regularly. Be careful to remove any detergent
residues from the dispenser drawer socket on the
machine.
Check the inlet hose at least once a year. If there are
any cracks, it should be replaced immediately: during
the wash cycles, water pressure is very strong and a
cracked hose could easily split open.
Keep the drawer to the left hand side when replacing it
to ensure that it centres the guides and to prevent it
from jamming.
Caring for your appliance drum
• Always leave the door ajar to prevent unpleasant
odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes,
small items (such as coins or buttons) may fall into the
protective pre-chamber at the base of the pump.
! Make sure the wash cycle has finished and unplug the
appliance.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble shooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre
(see “Assistance”), make sure that the problem cannot be not solved easily using the following list.
EN
Possible causes/Solution:
Problem
The machine does not switch on.
• The appliance is not plugged into the socket fully, or not enough to
make contact.
• There is no power to the socket, or the fuse has blown in the mains plug.
The wash cycle does not start.
• The door is not closed properly.
• The 'ON/OFF' button has not been pressed.
• The 'START/PAUSE' button has not been pressed.
• The water tap has not been turned on to allow water to flow into the machine.
• A delayed start has been set.
• The 'CHILD LOCK' is activated (see 'The machine just 'beeps' when a
programme or option is selected' below).
The machine does not fill with
water or Indicator light for the
first wash cycle flashing rapidly.
• The water inlet hose is kinked.
• The water inlet hose is not connected to the water supply.
• The water pressure is too low.
• The water tap has not been turned on to allow water to flow into the machine.
• There is no water supply to the house.
• The inlet valve filter is blocked.
• The 'START/PAUSE' button has not been pressed.
The machine continuously fills
with water and continually
drains away or Water left in the
drum or Stuck on wash.
• The top of the drain hose is too low - It must be fitted at a height
between 65 and 100 cm from the floor.
• The drain hose is connected incorrectly to the sink trap allowing water to
run into the machine, the drain hose must be positioned higher than the
bottom of the sink to prevent water flowing down the drain hose.
• The end of the drain hose has been pushed too far down the
standpipe, the 'U' bracket should be fitted 100 mm from the end of
the drain hose.
The machine does not drain or
spin - (error lights flashing).
• The Pump filter is blocked.
• The drain hose is kinked.
• New Installation - The blanking cap or spigot has not been removed
if connected under a sink.
• The drain hose or sink trap is blocked.
The machine does not spin.
• The Spin Speed is set to “
” position.
The machine does not drain or
spin.
• The 'BABY' program has been selected, at the end of the program the
machine drum will rotate slowly. To complete the wash cycle press the
'START/PAUSE'.
• The 'SILK' program is selected, at the end of the program it requires the
drain phase to be started. To complete the program press either the
'START/PAUSE'.
The programme takes too long.
• Programme times will vary due to water pressure, the incoming water
temperature and if the wash load goes out of balance. This will
increase the programme times accordingly (see 'The machine wont
spin properly' below).
• The display time is for guidance only - it is not a precise time to
finish and may vary.
The Display sticks at one 'time to
end' for more than 1 Minute or the
Display changes the estimated 'Time
to End' during the programme.
The machine vibrates a lot
during the spin cycle.
• The feet have not been adjusted, enabling the machine to rock.
• New Installation - Either the Transit Bolts including the plastic spacers,
or the Polystyrene Packaging have not been removed when installing the
machine.
• The machine is trapped between cabinets and/or walls.
• The load is in a slight out of balance condition and machine is spinning,
but at a lower speed.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
• There will always be some motor, pump and drum noise during spin.
The machine is noisy.
EN
The machine wont spin properly.
• Out of Balance detected when attempting to go into a spin cycle - If this
happens the machine will continue to try to repeat the distribution of the
load required before the machine will go into higher spin speeds - This will
increase the programme time accordingly. This is a safety feature to
prevent damage. Out of Balance can be caused by washing a single heavy
item (eg duvet, quilt, etc). - Try the programme again using a different load.
• The dispenser drawer is blocked with detergent and requires cleaning.
• The water pressure is too high and requires turning down - turn down
the tap on the water supply pipe slightly and try again.
The machine leaks from the
dispenser.
• The machine is tilting forwards - It must be level when in its final position.
• The fill hose is loose, check both the cabinet and tap ends.
• The fill hose is tight but still leaks, if so replace the rubber washers, or
the fill hose is missing the rubber washer.
The machine leaks (other than
dispenser).
• The drain hose is not fixed in properly.
• Switch off the machine and unplug it, wait for approximately 1 minute
and then switch it back on again If the problem persists contact the
Technical Assistance Service.
The Phase in Progress indicator
lights flash rapidly at the same
time as the ON/OFF indicator light.
• The machine requires a service wash. Run a 90 degree wash cycle with
detergent and no laundry.
The machine smells.
• The door will not open until the door lock indicator light goes out
shortly after the program has finished.
The machine door cannot be
opened.
• If there is no power to the machine you need to perform the manual
unlocking procedure.
• The door seal has drainage holes at the bottom - This is normal.
Door Seal damaged at the
bottom.
• The water level is correct if it can be seen at the bottom of the door.
The water level is too low when
the machine is washing.
• To exit, switch machine off, then press and hold 'ON/OFF' and 'START/
PAUSE' buttons simultaneously for 3 seconds Note the machine will
need the language resetting.
The word 'dON' appears
intermittently in the display
window and the drum slowly turns.
The machine just 'beeps' when a
programme or option is selected
(Child Lock Symbol is lit).
• Deactivate the Child Lock feature by pressing and holding in the 'CHILD
LOCK' button for 2 seconds.
There is too much foam.
• The detergent is not suitable for machine washing (it should display the
text 'for washing machines' or 'hand and machine wash' or the like).
• Too much detergent was used - less detergent is required in soft water.
After completing the
• To comply with new energy saving regulations the machine is fitted
with an automatic standby system. Press 'ON/OFF' button for 3
seconds to activate the machine, it can then either be switched off or
a new programme selected.
programme, or before starting a
programme, the machine has
turned itself off (no lights).
General.
• Your washing machine contains sensors that monitor progress during
the wash cycle (eg: Water Levels, Temperatures, Out of Balance
loads, Wash time/progress). Normally, if your machine successfully
completes the cycle, there is unlikely to be anything wrong!
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting:
Possible causes / Solutions:
EN
The machine's washing
performance is unsatisfactory.
• The tanks have not been loaded correctly (e.g. fabric softener has been
added instead of detergent or vice-versa)
• Two different types of detergent/fabric softener have mixed.
! NEVER mix two different detergents; always clean out the tanks before adding
a new type of detergent.
• The "Auto Dose System” is blocked due to prolonged lack of use: carry
out a tank cleaning cycle (refer to "Cleaning cycle pre-set by user").
What happens if the tanks are • Buzzers (Beep) and visual signals (icons appearing on the display) indicate
loaded even if they are already full? that the tank is full. If further detergent/fabric softener is added, the excess
quantity will fall into the drum and will be washed away with the next cycle.
What happens if the dispenser is
used in the traditional mode while
the tanks are still full?
• The machine will automatically track whether powder or liquid detergent
has been loaded in the traditional mode and will not intake any amount of
detergent from the tank. Fabric softener can only be used in the "Auto
Dose System” mode.
Can the tanks also be used for
powder detergent?
• No, powder detergent can only be used in the traditional mode.
Can powder detergent fall into the
tanks?
• No, there is a barrier to prevent powder detergent from falling into one of
the tanks even if the dispenser is open in the "Auto Dose System" position
(i.e. completely open).
What happens if the dispenser is • If the dispenser is not completely open, the detergent or fabric softener
not opened properly when filling the that has been added will fall into the drum and will be washed away with
tanks?
the next cycle.
What happens if detergent and
fabric softener are erroneously
inverted?
• The washing machine will wash with unsatisfactory results, the tanks will
have to be emptied and subjected to a manual cleaning cycle.
What happens if different
detergents are mixed before the
tanks are empty?
• The machine will wash normally although we recommend only refilling the
tanks after the signal emitted by the machine; do not mix different
detergents/fabric softeners.
Remember, you will be charged for a service call for problems caused by incorrect installation,
as listed above.
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.
Do not wash items which do not have a wash label, or wash items that are not intended as machine
washable.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Assistance
Guarantee
12 Months Parts and Labour Guarantee
EN
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of
breakdown repairs for twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective
because of either workmanship or materials, we will, at our discretion, either repair or replace the
appliance at no cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our
operating and maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise
interfered with by any person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
Damage resulting from transportation, improper use, neglect or interference or as a result
of improper installation.
-
-
Replacement of any consumable item or accessory . These include but are not limited to: plugs,
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL
OR NON-DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on
you registering your appliance with us and the parts being fitted by one of our authorised engineers.
There will be a charge for our engineer's time. To activate the extra parts warranty on your
appliance, simply call our registration line on 08448 24 24 24 (ROI 01 230 0800).
Extended Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the
expense of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on
08448 226 226 (Republic of Ireland 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint
Service Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone
assistance, or, where necessary, to arrange for an engineer to call. If we cannot resolve the
technical problem we will replace your machine or, if you prefer, give you your money back.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
After Sales Service
No one is better placed to care for your Hotpoint appliance during the course of its
working life than us - the manufacturer.
EN
Essential Contact Information
Hotpoint Service
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and
1000 fully qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts
guarantee you must register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the
right to use quality, recycled components to keep down customer costs and minimise material
wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,
remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts
19
Download from Www.Somanuals.com. All Manuals Search And Download.
195093871.00
07/2011
-
Xerox Fabriano
EN
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|