GA630RTX
GB630RTX
GA640.1RX
GB640.1RX
GA641X
GX641RX
GB641X
GA750X
GA750TX
GB750X
GX751RTX
GA761RFX
GBD641EIX
English
Operating Instructions
HOB
Contents
Operating Instructions,1
Warnings,2
Assistance,3
Description of the appliance,4
Installation,5
Start-up and use,10
Precautions and tips,11
Maintenance and care,12
Troubleshooting,12
After Sales Service,13
Guarantee,14
08448 24 24 24
Please phone us on
Download from Www.Somanuals.com. All Manuals Search And Download.
guarantee
to activate your
GB
Assistance
Communicating:
•
•
•
The type of problem encountered.
appliance model (Mod.)
serial number (S/N)
This information is found on the data plate located on the appliance and/or
on the packaging.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the appliance
Overall view
1
2
3
4
5
Support Grid for COOkWAre
GAs Burners
Control Knobs for GAs Burners
Ignition for GAs Burners*
sAfety DevICes*
•
GAs Burners differ in size and power. Use the diameter of the cookware
to choose the most appropriate burner to cook with.
•
•
•
GAs Burner IGnItIOn*enables a specific burner to be lit automatically.
Control Knobs for GAs Burners adjust the size of the flame.
sAfety DevICe* stops the gas flow if the flame is accidentally
extinguished.
* Only available on certain models.
2
2
1
1
3
3
5
4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
! Before operating your new appliance please read this instruction booklet
carefully. It contains important information for safe use, installation and care
of the appliance.
GB
If the hob is installed beneath a wall cabinet,
the latter must be situated at a minimum of
700 mm above the hob.
600mm min.
! Please keep these operating instructions for future reference. Pass them on
to possible new owners of the appliance.
Positioning
•
The installation cavity should have the dimensions indicated in the figure.
Fastening hooks are provided, allowing you to fasten the hob to tops that
are between 20 and 40 mm thick. To ensure the hob is securely fastened
!Keep packaging material out of the reach of children. It can become a choking
or suffocation hazard (see Precautions and tips).
to the top, we recommend you use all the hooks provided.
! The appliance must be installed by a qualified professional according to the
instructions provided. Incorrect installation may cause harm to people and
animals or may damage property.
55 mm
475
mm
! This unit may be installed and used only in permanently ventilated rooms
in accordance with current national regulations. The following requirements
must be observed:
•
The room must be equipped with an air extraction system that expels
any combustion fumes. This may consist of a hood or an electric fan that
automatically starts each time the appliance is switched on.
555 mm
•
Before fastening the cooktop in place, position the seal (supplied) along
the perimeter of the countertop, as shown in the figure.
In a chimney stack or branched flue.
(exclusively for cooking appliances)
Directly to
the Outside
•
The room must also allow proper air circulation, as air is needed for
combustion to occur normally. The flow of air must not be less than 2 m3/h
per kW of installed power.
Hook fastening diagram
The air circulation system may take air directly
from the outside by means of a pipe with an
inner cross section of at least 100 cm2; the
opening must not be vulnerable to any type
Hooking position for top H=20mm
Hooking position for top H=30mm
front
A
of blockages.
Examples of
ventilation holes
for comburant air.
The system can also provide the air needed
Adjacent
Room
Room to be
Vented
for combustion indirectly, i.e. from adjacent
rooms fitted with air circulation tubes as
described above. However, these rooms must
not be communal rooms, bedrooms or rooms
that may present a fire hazard.
Enlarging the ventilation slot
between window and floor.
Hooking position for top H=40mm
Back
! Use the hooks contained in the “accessory pack”.
fitting the appliance
The following precautions must be taken when installing the hob:
•
Where the hob is not installed over a built-in oven, a wooden panel must
be installed as insulation. This must be placed at a minimum distance of
20 mm from the lower part of the hob.
•
•
•
Kitchen cabinets adjacent to the appliance and taller than the top of the
hob must be at least 600 mm from the edge of the hob.
Hoods must be installed according to their relative installation instruction
manuals and at a minimum distance of 650 mm from the hob (see figure).
Place the wall cabinets adjacent to the hood at a minimum height of 420
mm from the hob (see figure).
ventilation
To ensure adequate ventilation, the back panel of the cabinet must be
removed. It is advisable to install the oven so that it rests on two strips of
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
5
Download from Www.Somanuals.com. All Manuals Search And Download.
wood, or on a completely flat surface with an opening of at least 45 x 560
mm (see diagrams).
As the colours of the wires in the mains lead may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
GB
Connect the Green & Yellow wire to terminal marked “E” or
Green or Green & Yellow.
or coloured
Connect the Brown wire to the terminal marked “L” or coloured Red or Brown.
Connect the Blue wire to the terminal marked “N” or coloured Black or Blue.
FAILURE TO OBSERVE THE ACCIDENT-PREVENTION REGULATIONS
RELIEVES THE MANUFACTURER OF ALL LIABILITY.
replacing the cable
Use a rubber cable of the type H05RR-F with a suitable cross section 3 x
0.75 mm².
The yellow-green earth wire must be 2-3 cm longer than the other wires.
! The hob can only be installed above built-in ovens with a cooling ventilation
system.
Gas connection
Where a hob is installed above an oven without a forced ventilation cooling
system, adequate ventilation must be provided inside the cabinet by means
of air holes through which air can pass (see figure).
The appliance should be connected to the main gas supply or to a gas
cylinder in compliance with current national regulations. Before carrying out
the connection, make sure the cooker is compatible with the gas supply you
wish to use. If this is not the case, follow the instructions indicated in the
paragraph “Adapting to different types of gas.”
When using liquid gas from a cylinder, install a pressure regulator which
complies with current national regulations.
!Check that the pressure of the gas supply is consistent with the values indicated
inTable 1 (“Burner and nozzle specifications”).This will ensure the safe operation
and longevity of your appliance while maintaining efficient energy consumption.
Connection with a rigid pipe (copper or steel)
electrical connection
! Connection to the gas system must be carried out in such a way as not to
! THIS APPLIANCE MUST BE EARTHED.
place any strain of any kind on the appliance.
The hob is designed to work with alternating current, the supply voltage and
frequency indicated on the rating plate (situated under the hob). Make sure
that the local supply voltage corresponds to the voltage indicated on the
rating plate.
There is an adjustable L-shaped pipe fitting on the appliance supply ramp
and this is fitted with a seal in order to prevent leaks. The seal must always
be replaced after rotating the pipe fitting (seal provided with appliance). The
gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment.
Connecting the supply cable to the mains electricity supply
Connecting a flexible jointless stainless steel pipe to a threaded
attachment
The gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment.
These pipes must be installed so that they are never longer than 2000 mm
when fully extended. Once connection has been carried out, make sure that
the flexible metal pipe does not touch any moving parts and is not compressed.
For models supplied without a plug, fit a standard plug suitable for the load
indicated on the rating plate, onto a cable and connect to a suitable socket.
To connect direct to the mains supply, a double pole switch with a contact
separation of at least 3mm suitable for the load and complying with current
standards and regulations must be fitted between the appliance and the
mains supply outlet.
The green-yellow earth wire must not be interrupted by the switch.
The supply cable must be positioned so that no part of it reaches a temperature
of 50°C above room temperature. For installation above a built-under
oven, the hob and the oven must be connected separately to the electricity
supply, both for safetly reasons and for easy removal of the oven for repair,
maintenance etc.
! Only use pipes and seals that comply with current national regulations.
Checking the tightness of the connection
! When the installation process is complete, check the pipe fittings for leaks
using a soapy solution. Never use a flame.
Adapting to different types of gas
DO NOT use adapters as they could cause overheating or burning.
Before connecting to the power supply, make sure that:
To adapt the hob to a different type of gas other than default type (indicated
on the rating plate at the base of the hob or on the packaging), the burner
nozzles should be replaced as follows:
1. Remove the hob grids and slide the burners off their seats.
2. Unscrew the nozzles using a 7 mm socket spanner, and replace them
with nozzles for the new type of gas (see table 1 “Burner and nozzle
characteristics”).
3. Reassemble the parts following the above procedure in the reverse order.
4. Once this procedure is finished, replace the old rating sticker with one
indicating the new type of gas used. Sticker are available from any of our
Service Centres.
•
•
•
The limiter switch and the domestic system can withstand the load from
the appliance (see rating plate).
The supply system is efficiently earthed according to standards and laws
in force.
The socket or double-pole switch are easily accessible when the appliance
is installed.
! The wires in the mains lead are coloured in accordance with the following
code:
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the nozzles on separate “double flame “ burners
1. Remove the grids and slide the burners from their housings. The burner
consists of 2 separate parts (see figure);
6. In the event of discrete-adjustment knobs with LED visualisation, turn the
knob to the minimum power setting them remove it and intervene on the
adjustment screw located near the tap pin.
GB
2. Unscrew the burers with a 7 mm wrench spanner. The internal burner
has a nozzle, the external burner has two (of the same size). Replace
the nozzle with models suited to the new type of gas (see table 1).
3. Replace all the components by repeating the steps in reverse order.
7. Minimum setting adjustment of the DRDA (DCDR) burner with discrete
adjustment and LED visualisation:
•
•
•
To adjust the outer ring, turn the knob anti-clockwise to the minimum
power position.
To adjust the minimum power setting of the inner ring, turn the knob
clockwise to the minimum power position.
Remove the knob and intervene on the adjustment screw located near
the tap pin.
! If the appliance is connected to liquid gas, the regulation screw must be
fastened as tightly as possible.
! Once this procedure is finished, replace the old rating sticker with one
indicating the new type of gas used. Stickers are available from any of our
Service Centres.
replacing the triple ring burner nozzles
1. Remove the pan supports and lift the burners out of their housing. The
burner consists of two separate parts (see pictures).
2. Unscrew the nozzles using a 7 mm socket spanner. Replace the nozzles
with models that are configured for use with the new type of gas (see Table
1). The two nozzles have the same hole diameter.
! Should the gas pressure used be different (or vary slightly) from the
recommended pressure, a suitable pressure regulator must be fitted to the
inlet pipe (in order to comply with current national regulations).
3. Replace all the components by completing the above operations in reverse
order.
DATA PLATE
Electrical
see data plate
connections
This appliance conforms to the following
European Economic Community directives:
- 2006/95/EEC dated 12/12/06 (Low
Voltage) and subsequent amendments
- 2004/108/EEC dated 15/12/04
(Electromagnetic Compatibility) and
subsequent amendments
- 93/68/EEC dated 22/07/93 and
subsequent amendments.
•
Adjusting the burners’ primary air
- 2009/142/EEC dated 30/11/09 (Gas) and
subsequent amendments.
Does not require adjusting.
- 2012/19/EC and subsequent
amendments.
•
Setting the burners to minimum
1. Turn the tap to the low flame position;
2. Remove the knob and adjust the adjustment screw, which is positioned
in or next to the tap pin, until the flame is small but steady.
! In the event of single-control DRDA (DCDR) burners, adjustment can be
performed by intervening on the 2 screws located near the tap pin (see picture).
Total DRDA
(DCDR) burner
adjustment
Inner DRDA (DCDR)
burner adjustment
3. Having adjusted the flame to the required low setting, while the burner is
alight, quickly change the position of the knob from minimum to maximum
and vice versa several times, checking that the flame does not go out.
4. Some appliances have a safety device (thermocouple) fitted. If the device
fails to work when the burners are set to the low flame setting, increase
this low flame setting using the adjusting screw.
5. Once the adjustment has been made, replace the seals on the by-passes
using sealing wax or a similar substance.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Burner and nozzle specifications (for 65 cm versions only)
GB
Table 1
Liquid Gas
Natural Gas
Burner
Diameter Thermal
Thermal By-pass Nozzle
Flow*
(g/h)
Thermal Nozzle
Flow*
(l/h)
power
kW
power
kW
1/100
1/100
power
kW
1/100
(p.c.s.*)
(p.c.s.*)
(p.c.s.*)
Nominal
(mm)
100
100
75
Reduced Nominal (mm)
(mm)
86
***
**
214
(mm)
132 (H3)
122 (H3)
96 (Z)
Fast (R)
0.70
0.70
0.40
0.40
1.50
3.00
2.60
1.65
1.00
3.30
39
39
28
28
61
218
189
120
73
3.00
2.60
1.65
1.00
3.60
286
248
157
95
Reduced Fast (RR)
Semi Fast (S)
Auxiliary (A)
80
186
118
71
64
55
50
79 (6)
Triple Crown (TC)
130
65x2
240
236
103x2
343
Double flame
(DCDR internal) (1)
36
0.30
0.90
29
44
65
64
0.90
74
86
(DCDR
Double
flame (1)
29
57
44
74
internal)
130
1.50
3.60
262
257
3.60
343
(DCDR
external
2 nozzle)
60x2
94x2
Double Flame
36
44
86
0.40
1.50
0.90
3.60
28
61
65
64
0.90
3.60
74
(DCDR Internal) (2)
Double Flame
(DCDR External)
2 nozzle (2)
130
67x2
343
262
257
100x2
Nominal (mbar)
Minimum (mbar)
Maximum (mbar)
28-30
20
35
37
25
45
20
17
25
Supply pressures
(1) For single-control DRDA (DCDR) burner only
(2) For dual-control DRDA (DCDR) burner only
*
**
***
At 15°C and 1013,25 mbar - dry gas
Propane P.C.S. = 50.37 MJ/Kg
Butane P.C.S. = 49.47 MJ/Kg
Natural P.C.S. = 37.78 MJ/m³
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Burner and nozzle specifications (for 75 cm versions only)
GB
Table 1
Liquid Gas
Natural Gas
Burner
Diameter Thermal
Thermal By-pass Nozzle
Flow*
(g/h)
Thermal Nozzle
Flow*
(l/h)
power
kW
power
kW
1/100
1/100
power
kW
1/100
(p.c.s.*)
(p.c.s.*)
(p.c.s.*)
Nominal
(mm)
100
75
Reduced Nominal (mm)
(mm)
80
***
**
186
(mm)
122 (H3)
96 (Z)
Reduced Fast (RR)
Semi Fast (S)
0.70
0.40
0.40
1.50
0.70
0.70
2.60
1.65
1.00
3.30
3.40
1.50
39
28
28
61
39
39
189
120
73
2.60
1.65
1.00
3.60
3.40
1.50
248
157
95
64
118
71
Auxiliary (A)
55
50
79 (6)
Triple Crown (TC)
Ultrarapid (UR)
130
100
—
65x2
91
240
247
109
236
243
107
103x2
343
324
143
138 (H3)
88 (X)
Semi-Fishburner (SP)
60
Double Flame
36
0.40
0.90
28
44
65
64
0.90
74
86
(DCDR Internal) (2)
Double Flame
(DCDR External)
2 nozzle (2)
130
36
1.50
0.30
4.10
0.90
61
29
70x2
44
298
65
293
64
4.10
0.90
110x2
72
390
86
Double flame
(DCDR internal) (1)
(DCDR
Double
flame (1)
29
57
44
72
internal)
130
1.50
3.9
284
279
3.90
371
(DCDR
external
2 nozzle)
70 x 2
96x2
Nominal (mbar)
Minimum (mbar)
Maximum (mbar)
28-30
20
35
37
25
45
20
17
25
Supply pressures
(1) For single-control DRDA (DCDR) burner only
(2) For dual-control DRDA (DCDR) burner only
*
**
***
At 15°C and 1013,25 mbar - dry gas
Propane P.C.S. = 50.37 MJ/Kg
Butane P.C.S. = 49.47 MJ/Kg
Natural P.C.S. = 37.78 MJ/m³
A
A
S
TC
DC
R
RR
S
DC
S
S
GA 630 R T X
GB 630 R T X
GA 641 X
GB 641 X
GA 640.1 R X
GX 641 R X
GBD641EIX
GB 640.1 R X
RR
S
S
RR
S
S
RR
A
S
A
DC
TC
UR
TC
DC
SP
A
A
GA 761 R F X
GA 750 X
GB 750 X
GX 751 R T X
GA 750 T X
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
9
Download from Www.Somanuals.com. All Manuals Search And Download.
The knob marked with the symbol
The knob marked with the symbol
controls the outer ring.
controls the inner ring.
start-up and use
GB
! The position of the corresponding gas burner is shown on every knob.
To activate any one of the two rings, press the corresponding knob and turn
it anti-clockwise to the maximum power setting
In order to use the double-flame burner to its full potential, avoid
simultaneously setting the inner ring to minimum power and the outer
ring to maximum power.
Gas cooker hobs are equipped with discrete power adjustment that allows
for accurately adjusting the flame to 5 different power levels. Thanks to this
system, gas hobs are also capable of guaranteeing the same cooking results
for each recipe, as the optimal power level for the desired type of cooking can
be identified in an easier, more accurate way.
.
single control:
Gas burners
The rings comprising the burner are activated through a single control knob.
Each burner can be adjusted to one of the following settings using the
corresponding control knob:
To simultaneously turn on both rings, position the knob on the symbol
(max) -
(min) then press and turn the knob anti-clockwise.
●
Off
Maximum
Minimum
To turn on the inner ring only, position the knob on the symbol
(min) then press and turn the knob clockwise.
(to switch modes, it is necessary to switch off the burner).
(max ) -
To light one of the burners, hold a lit match or lighter near the burner and, at
the same time, press down and turn the corresponding knob anti-clockwise
to the maximum setting.
To switch off the burner, press and turn the knob clockwise until it stops (when
it reaches the “●” position).
Since the burner is fitted with a safety device, the knob should be pressed
for approximately 2-3 seconds to allow the automatic device keeping the
flame alight to heat up.
When using models with an ignition button, light the desired burner pressing
down the corresponding knob as far as possible and turning it anticlockwise
towards the maximum setting.
Practical advice on using the burners
To ensure the burners operate efficiently:
•
Use appropriate cookware for each burner (see table) so that the flames
do not extend beyond the bottom of the cookware.
•
•
Always use cookware with a flat base and a cover.
When the contents of the pan reach boiling point, turn the knob to minimum.
Burner
Ø Cookware diameter (cm)
! If a flame is accidentally extinguished, turn off the control knob and wait for
at least 1 minute before trying to relight it.
Rapid (R)
24 - 26
24 - 26
16 - 20
10 - 14
24 - 26
10 - 14
24 - 26
Reduced Rapid (RR)
Semi Rapid (S)
To switch off the burner, turn the knob in a clockwise direction until it stops
(when reaches the “●” position).
Auxiliary (A)
Discrete flame adjustment
Triple Crown (TC)
The selected burner can be adjusted - by means of the knob - to 5 different
power levels. To shift between levels, simply turn the knob towards the
desired power level.
Double Flame (DCDR internal)
Double Flame (DCDR external)
A click signals the passage from one power level to the other.
Pans to be used on 65 cm hobs
The selected power level is indicated by the
Burner
Ø Cookware Diameter (cm)
correspondingsymbol(symbols
)
Reduced Rapid (RR)
Semi-Rapid (S)
24 - 26
16 - 20
10 - 14
16 - 20
24 - 26
24 - 26
10 - 14
26 - 28
and, on hobs equipped with a display, by the
LEDs that turn on (5 = max. power; 1 = min.
power). The system guarantees accurate
flame adjustment and uniform cooking
results by facilitating selection of the desired
power level.
Auxiliary (A)
Semi-Fishburner (SP)
Triple Crown (TC)
Ultra Rapid (UR)
The “double-flame” burner
Double Flame (DCDR internal)
Double Flame (DCDR external)
Pans to be used on 75 cm hobs
This gas burner consists of two concentric flame rings that can operate jointly
or independently (in case of dual-control only).
As the burner is fitted with a safety device, the knob should be pressed
down for approximately 2-3 seconds until the device keeping the flame
automatically alight heats up.
! On the models supplied with a reducer shelf, remember that this should be
used only for the Double flame internal (DCDR internal) burner when you use
casserole dishes with a diameter under 12 cm.
To identify the type of burner, refer to the designs in the section entitled, “Burner
and Nozzle Specifications”.
Dual control:
Each ring comprising the burner has its own control knob:
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
10
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
The appliance must not be installed outdoors, even in covered areas. It is
extremely dangerous to leave the appliance exposed to rain and storms.
Do not touch the appliance with bare feet or with wet or damp hands and
feet.
The appliance must be used by adults only for the preparation of food,
in accordance with the instructions outlined in this booklet.Any other
use of the appliance (e.g. for heating the room) constitutes improper
use and is dangerous. the manufacturer may not be held liable for
any damage resulting from improper, incorrect and unreasonable
use of the appliance.
Practical Advice on using the Half fish-kettle Burner *
The two “Half Fish-Kettle” burners, are eliptic in form and can be turned up
to 90°. This makes the cooktop more flexible in terms of how it can be used.
GB
•
•
•
•
•
•
Ensure that the power supply cables of other electrical appliances do not
come into contact with the hot parts of the oven.
The openings used for ventilation and dispersion of heat must never be
covered.
Always make sure the knobs are in the “”/“” position when the appliance
is not in use.
When unplugging the appliance always pull the plug from the mains socket,
do not pull on the cable.
Never carry out any cleaning or maintenance work without having detached
the plug from the mains.
In case of malfunction, under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the appliance. Contact a Service
Centre (see Assistance).
Always make sure that pan handles are turned towards the centre of the
hob in order to avoid accidental burns.
Do not close the glass cover (if present) when the gas burners or electric
hotplates are still hot.
To turn the two burners 90°, proceed as follows:
•
•
•
•
Make sure that the burners are cool;
Lift the burner completely out of its housing;
Replace it in its housing in the position desired;
Make sure that the burners are positioned correctly before use.
In addition, the two burners can be used in tandem or speartely with cookware
of different shapes and sizes:
•
•
Double burner for a fish-kettle or oval cookware (Fig. A).
Double burner for a griddle or rectangular/square cookware with minimum
dimensions of 28x28 cm (Fig. B)
•
•
Single burner for medium size cookware (diameter of 16-20 cm) (Fig. C).
NEVER use the double burner in the configuration represented in
figure D.
•
•
•
•
•
•
Do not leave the electric hotplate switched on without a pan placed on it.
Do not use unstable or deformed pans.
remove any liquid from the lid before opening it.
The appliance should not be operated by people (including children)
with reduced physical, sensory or mental capacities, by inexperienced
individuals or by anyone who is not familiar with the product. These
individuals should, at the very least, be supervised by someone who
assumes responsibility for their safety or receive preliminary instructions
relating to the operation of the appliance.
Fig. A
Fig. B
•
•
Do not let children play with the appliance.
the appliance is not intended to be operated by means of an external
timer or separate remote-control system.
Fig. C
Fig. D
Disposal
•
•
When disposing of packaging material: observe local legislation so that the
packaging may be reused.
The European Directive 2012/19/EC on Waste Electrical and Electronic
Equipment (WEEE), requires that old household electrical appliances
must not be disposed of in the normal unsorted municipal waste stream.
Old appliances must be collected separately in order to optimise
the recovery and recycling of the materials they contain and reduce
the impact on human health and the environment. The crossed out
“wheeled bin” symbol on the product reminds you of your obligation,
that when you dispose of the appliance it must be separately collected.
Consumers may take their old appliance to public waste collection
areas, other communal collection areas, or if national legislation
allows return it to a retailer when purchasing a similar new product.
All major household appliance manufacturers are active in the creation of
systems to manage the collection and disposal of old appliances.
Precautions and tips
! This appliance has been designed and manufactured in compliance with
international safety standards. The following warnings are provided for safety
reasons and must be read carefully.
General safety
•
•
this is a class 3 built-in appliance.
Gas appliances require regular air exchange to maintain efficient
operation. When installing the hob, follow the instructions provided
in the paragraph on “Positioning” the appliance.
•
•
these instructions are only valid for the countries whose symbols
appear in the manual and on the serial number plate.
The appliance was designed for domestic use inside the home and is not
intended for commercial or industrial use.
* Only available on certain models.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
troubleshooting
GB
It may happen that the appliance does not function properly or at all. Before
calling the service centre for assistance, check if anything can be done. First,
check to see that there are no interruptions in the gas and electrical supplies,
and, in particular, that the gas valves for the mains are open.
switching the appliance off
Disconnect your appliance from the electricity supply before carrying out
any work on it.
Cleaning the appliance
The burner does not light or the flame is not even around the burner.
Check whether:
! Do not use abrasive or corrosive detergents such as stain removers, anti-rust
products, powder detergents or sponges with abrasive surfaces: these may
scratch the surface beyond repair.
•
•
•
The gas holes on the burner are clogged.
All the movable parts that make up the burner are mounted correctly.
There are draughts near the appliance.
! Never use steam cleaners or pressure cleaners on the appliance.
The flame dies in models with a safety device.
Check to make sure that:
•
•
•
It is usually enough to wash the hob with a damp sponge and dry it with
absorbent kitchen roll.
•
•
•
You pressed the knob all the way in.
The removable parts of the burners should be washed frequently with
warm water and soap and any burnt-on substances removed.
For hobs which ligth automatically, the terminal part of the electronic instant
lighting devices should be cleaned frequently and the gas outlet holes
should be checked for blockages.
You keep the knob pressed in long enough to activate the safety device.
The gas holes are not blocked in the area corresponding to the safety
device.
the burner does not remain lit when set to minimum.
Check to make sure that:
•
Stainless steel can be marked by hard water that has been left on the
surface for a long time, or by aggressive detergents containing phosphorus.
After cleaning, rinse and dry any remaining drops of water.
•
•
•
The gas holes are not blocked.
There are no draughts near the appliance.
The minimum setting has been adjusted properly.
! It is not necessary to remove the pan supports in order to clean the hob
surface. Thanks to the support system, simply lift and hold the pan supports
or rotate them until they rest against a rear support.
the cookware is unstable.
Check to make sure that:
•
•
•
The bottom of the cookware is perfectly flat.
The cookware is positioned correctly at the centre of the burner.
The pan support grids have been positioned correctly.
Clening tips for the hotplates with logo
To remove all types of stains just wipe with a smooth cloth, wet with hot water.
For stronger stains, we recommend the use of common detergent for dishes,
with a cloth dampened with hot water, to ensure a perfect cleaning result.
! never use aggressive detergents or coarse sponges because they
can cause irreversible damage to the special protection treatment with
formation of irremovable stains and halos.
Gas tap maintenance
Over time, the taps may become jammed or difficult to turn. If this happens,
the tap must be replaced.
! This procedure must be performed by a qualified technician authorised
by the manufacturer.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
12
Download from Www.Somanuals.com. All Manuals Search And Download.
After sales service
GB
No one is better placed to care for your Hotpoint appliance during the course of its working life than us – the
manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in the country offering you access to 400 skilled telephone advisors and 1000
fully qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically
clean your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee you
must register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling and Disposal Information
As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves the right to use
quality, recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the
door, plug, and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that
the appliance can no longer be plugged into mains socket, and the door cannot be locked shut.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
GB
12 months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for
twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by
any person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation
Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,
batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-
DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering
your appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for
our engineer’s time. To activate the extra parts warranty on your appliance, simply call our registration line on
08448 24 24 24 (Republic of Ireland 01 230 0800)
Extended Guarantees
We offer a selection of protection plans that enable you to fully cover yourself against the expense of repair bills
for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226 (Republic of
Ireland 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you experience
any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service Hotline on 08448
224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an
engineer to call.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
14
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
15
Download from Www.Somanuals.com. All Manuals Search And Download.
195097459.03
01/2014 - XerOX fABrIAnO
GB
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|