Hotpoint Cooktop CBRA 640 X S User Manual

Operating Instructions

HOB

Contents

Warnings, 2

Installation, 3-5

Positioning

Electrical connection

English,1

Description of the appliance, 6-7

Control panel

Extendable cooking zones

Start-up and use, 8-10

Switching on the hob

Switching on the cooking zones

Switching off the cooking zones

Power function

Heating elements

Control panel lock

CRA 641 D C

KSC 640 X S

CBRA 640 X S

Switching off the hob

Practical advice on using the appliance

Safety devices

Practical cooking advice

Precautions and tips, 11

General safety

Disposal

Care and maintenance, 12

Switching the appliance off

Cleaning the appliance

Disassembling the hob

Technical description of the models, 13

After Sales Service, 15

Guarantee, 15

Key Contacts, 16

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

! Before operating your new appliance please read

this instruction booklet carefully. It contains important

information concerning the safe operation, installation

and maintenance of the appliance.

! Please keep these operating instructions for future

reference. Pass them on to any new owners of the

appliance.

min. 20 mm

COMPARTMENT

Positioning

min. 40 mm

! Keep all packaging material out of the reach of

children. It may present a choking or suffocation

hazard (see Precautions and tips).

! The appliance must be installed by a qualified

professional in accordance with the instructions

provided. Incorrect installation may cause harm to

people and animals or may damage property.

min. 20 mm

FAN-ASSISTED

OVEN

Built-in appliance

Use a suitable cabinet to ensure that the appliance

functions properly.

min. 40 mm

• The supporting surface must be heat-resistant up to

a temperature of approximately 100°C.

• If the appliance is to be installed above an oven,

the oven must be equipped with a forced ventilation

cooling system.

• Avoid installing the hob above a dishwasher: if this

cannot be avoided, place a waterproof separation

device between the two appliances.

• Depending on the hob you want to install, the

cabinet must have the following dimensions (see

ﬁgure):

FRONT SIDE

OF HOB

SUPPORTING

SURFACE

UNDERSIDE

OF HOB

520

Ventilation

To allow adequate ventilation and to avoid overheating of

the surrounding surfaces the hob should be positioned as

follows:

• At a minimum distance of 40 mm from the back

panel.

• So that a minimum distance of 20 mm is maintained

between the installation cavity and the cabinet

underneath.

• Kitchen cabinets adjacent to the appliance and taller

than the top of the hob must be at least 600 mm

from the edge of the hob.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Fixing

connection. Connect the wires in accordance with the

The appliance must be installed on a perfectly level

supporting surface.

instructions given in the following table and diagrams:

Voltage and

mains frequency

Electrical cable

Wire connection

Any deformities caused by improper fixing could affect

the features and operation of the hob.

: yellow/green

230-240V 1+N ~

220-240V 1+N ~

50/60 Hz

N: the two blue wires together

L: brown and black together

The thickness of the supporting surface should be taken

into account when choosing the length of the screws for

the fixing hooks:

Other types of connection

• 30 mm thick: 17.5 mm screws

• 40 mm thick: 7.5 mm screws

If the mains supply corresponds with one of the

following:

Voltage and mains frequency

• 400V - 2+N ~ 50/60 Hz

• 220-240V 3 ~ 50/60 Hz

Fix the hob as follows:

1. Use short flat-bottomed screws to fix the 4 alignment

springs in the holes provided at the central point of

each side of the hob.

• 230-240V 3 ~ 50/60 Hz

2. Place the hob in the cavity, make sure it is in a

central position and push down on the whole perimeter

until the hob is stuck to the supporting surface.

3. For hobs with raised sides: After inserting the hob

into its cavity, insert the 4 fixing hooks (each has its

own pin) into the lower edges of the hob, using the

long pointed screws to fix them in place, until the glass

is stuck to the supporting surface.

• 400V - 2+2N ~ 50/60 Hz

Separate the wires and connect them in accordance

with the instructions given in the following table and

diagrams:

Voltage and

mains frequency

Electrical cable

Wire connection

: yellow/green;

400V - 2+N ~

50/60 Hz

N: the two blue wires

together

L1: black

230-240V 3 ~

220-240V 3 ~

50/60 Hz

! The screws for the alignment springs must remain

accessible.

L2: brown

: yellow/green;

! In order to adhere to safety standards, the appliance

must not come into contact with electrical parts once it

has been installed.

N1: blue

N2: blue

L1: black

L2: brown

400V - 2+2N ~

50/60 Hz

! All parts which ensure the safe operation of the

appliance must not be removable without the aid of a

tool.

If the mains supply corresponds with one of the

following:

Voltage and mains frequency

• 400V 3 - N ~ 50/60 Hz

proceed as follows:

Electrical connection

! The electrical connection for the hob and for any built-

in oven must be carried out separately, both for safety

purposes and to make extracting the oven easier.

! The cable provided is not suitable for the following

types of installation.

1. Use a suitable supply cable, H05RR-F or higher, with

the right dimensions (cable cross section: 25 mm).

2. To open the terminal board, use a screwdriver as

a lever under the side tabs of the cover (see Terminal

board picture).

3. Loosen the cable clamp screw and the terminal

board screws in accordance with the type of

connection required and position the connection

supports as shown in the following table and diagrams.

4. Position the wires in accordance with the information

given in the following table and diagrams and connect

the appliance by tightening all the screws for the

springs as much as possible.

Terminal board

On the lower part of the appliance there is a

connection box for the different

UNDERSIDE OF HOB

types of electricity supply (the

picture is only an indication and

is not an exact representation

of the purchased model).

Single-phase connection

The hob is equipped with a pre-connected electricity

supply cable, which is designed for single-phase

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Voltage and

mains frequency

• The appliance is earthed and the plug is compliant

with the law.

Electrical connections

Terminal board

400V 3-N ~

50/60 Hz

• The socket can withstand the maximum power of

the appliance, which is indicated on the data plate

located on the appliance itself.

• The voltage falls within the range of values indicated

on the data plate.

Three-phase 400

5. Secure the power supply cable by fastening the

cable clamp screw, then put the cover back on.

Phase

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

Three-phase 400

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

Neutral

U-bolt

connection support

Earth

! The cable must not be bent or compressed.

Connecting the electricity supply cable to the mains

! The cable must be checked regularly and replaced

by authorised technicians only.

If the appliance is being connected directly to the

electricity mains an omnipolar switch must be installed

with a minimum opening of 3 mm between contacts.

! The manufacturer declines any liability should

these safety measures not be observed.

! The installer must ensure that the correct electrical

connection has been made and that it is fully compliant

with safety regulations.

! Do not remove or replace the power supply cable

for any reason. Its removal or replacement will void

the warranty and the CE marking. INDESIT does not

assume liability for accidents or damage arising from

replacement/removal of the original power supply

cable. Replacement can only be accepted when

carried out by personnel authorised by INDESIT and

using an original spare part.

Before connecting the appliance to the power supply,

make sure that:

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Description of the

appliance

Control panel

The control panel described in this manual is only a representative example: it may not exactly match the panel on

your appliance.

INCREASE

POWER button

POWER and

RESIDUAL HEAT

COOKING ZONE

ON/OFF

SELECTED indicator light

button

indicators

ON/OFF

indicator light

CONTROLS LOCKED

indicator light

CONTROL PANEL

LOCK button

COOKING ZONE

SELECTOR buttons

REDUCE POWER

button

• INCREASE POWER button switches on the hotplate

and controls the power (see Start-up and use).

• ON/OFF button switches the appliance on and off.

• ON/OFF indicator light shows whether the appliance

• REDUCE POWER button controls the power and

switches off the hotplate (see Start-up and use).

is on or off.

• CONTROL PANEL LOCK button prevents

accidental changes to the hob settings (see Start-up

and use).

• COOKING ZONE SELECTOR button shows a

particular cooking zone has been selected and

therefore various adjustments are possible.

• CONTROL PANEL LOCK indicator light shows the

control panel has been locked (see Start-up and use).

• COOKING ZONE SELECTOR button is used to

select the desired cooking zone.

! This product complies with the requirements of the

latest European Directive on the limitation of power

consumption of the standby mode.

• POWER indicator provides a visual display for the

current heat level.

If no operations are carried out for a period of 2

minutes, after the residual heat indicator lights turn

off and the fan stops (if present), the appliance

automatically switches to the “off mode”.

The appliance resumes the operating mode once the

ON/OFF button is pressed.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Extendable cooking zones

Certain models are fitted with extendable cooking zones. These may be circular or oval and may vary in their

extensibility (they may be double or triple hotplates). A list of controls is given below (these controls are only present

in models with the extendable cooking zone option).

Circular extendable hotplate

DOUBLE

HOTPLATE ON

indicator light

DOUBLE

HOTPLATE ON

button

• DOUBLE HOTPLATE ON button switches on the

double hotplate (see Start-up and use).

• DOUBLE HOTPLATE ON indicator light shows the

double hotplate has been switched on.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Start-up and use

! The glue applied on the gaskets leaves traces of

grease on the glass. Before using the appliance, we

recommend you remove these with a special non-

abrasive cleaning product. During the first few hours

of use there may be a smell of rubber which will

disappear very quickly.

Switching off the cooking zones

To switch off a cooking zone, select it using the

corresponding selector button

and:

• Press the button: the power of the cooking zone

will progressively decrease until it is switched off.

! A few seconds after the hob is connected to the

electricity supply, a buzzer will sound. The hob may

now be switched on.

Heating elements

Two types of heating element may be installed,

depending on the appliance model: halogen and

radiant elements.

Halogen elements emit heat via radiation from the

halogen lamps they contain.

! If the

button is pressed for an extended

period of time, the display scrolls quickly though the

power levels and timer minutes.

They have similar properties to gas burners: they are

easy to control and reach set temperatures quickly,

allowing you to see the power level instantly.

Radiant elements consist of a series of coils which

allow heat to be distributed evenly at the base of

the cookware, so that all slow-flame cooking may be

performed successfully, for example stews, sauces or

reheated dishes.

Switching on the hob

To switch the hob on, press and hold the

for approximately one second.

button

Switching on the cooking zones

Each cooking zone is controlled using a selector button

and a power adjustment device consisting of a

Control panel lock

When the hob is switched on, it is possible to lock the

oven controls in order to avoid accidental changes

being made to the settings (by children, during

double

and

button.

• To begin operating a cooking zone, press the

corresponding control button and set the desired

cleaning, etc.). Press the

panel: the indicator light above the button will switch

on.

button to lock the control

power level (between 0 and 9) using the buttons

and

To use any of the controls (e.g. to stop cooking), you

must switch off this function. Press the

few moments, the indicator light will switch off and the

lock function will be removed.

button for a

Power function

The power function for the cooking zones may be used

to shorten heating-up times. Activate and set the power

Switching off the hob

level for the desired cooking zone

as described

in the previous paragraph. Press and hold the selector

Press the

button to switch the appliance off.

button corresponding to the desired cooking zone

for at least 2 seconds. The display, the power level

indicator, will alternately show the letter “P” and the

power level set previously until the desired power level

has been reached. Once this level has been reached,

the display will revert to showing the set power level.

To deactivate this function, press and hold – for at

least 2 seconds - the selector button corresponding to

If the control panel lock has been activated, the

controls will continue to be locked even after the hob is

switched on again. In order to switch the hob on again,

you must first remove the lock function.

the cooking zone on which the

function has been

activated; alternatively, select a different power level

using the buttons

and

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety switch

Practical advice on using the appliance

The appliance has a safety switch which automatically

switches the cooking zones off after they have been

in operation for a certain amount of time at a particular

power level. When the safety switch has been

triggered, the display shows “0”.

To obtain the best results from your hob:

• Use pans with a thick, flat base in order to fully

utilise the cooking zone.

For example: the right rear hotplate is set to 5 and will

switch off after 5 hours of continuous operation, while

the front left hotplate is set to 2 and will switch off after

8 hours.

• Always use pans with a diameter which is large

enough to cover the hotplate fully, in order to use all

the available heat.

Power level

Maximum operating time in hours

• Make sure that the base of the cookware is always

clean and dry, in order to fully utilise and extend the

life of both the cooking zones and the cookware.

• Avoid using the same cookware which has been

used on gas burners: the heat concentration on gas

burners may distort the base of the pan, causing it

not to adhere correctly.

Safety devices

Overheating protection

Buzzer

If the electronic elements overheat, the hob switches

off automatically and

appears on the display,

This can also indicate several irregularities:

• An object (a pan, cutlery, etc.) has been placed on

the control panel for more than 10 seconds.

• Something has been spilt on the control panel.

• A button has been pressed for too long. All of the

above situations may cause the buzzer to sound.

Remove the cause of the malfunction to stop the

buzzer. If the cause of the problem is not removed,

the buzzer will keep sounding and the hob will

switch off.

followed by a flashing number. When the temperature

has reached a suitable level, this message disappears

and the hob may be used again.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Practical cooking advice

Pressure cooking

Pressure cooker

Frying

•

Grilling

Boiling

•

Crêpes

Cooking on a high flame and browning

(roasts, steaks, escalopes, fish fillets,

fried eggs)

Fast thickening (liquid juices)

Boiling water (pasta, rice, vegetables)

Milk

Slow thickening (dense juices)

Bain-marie cooking

Pressure cooking after whistle

™

Low-flame cooking (stews)

Reheating dishes

™

Chocolate sauce

Keeping food hot

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions and tips

! This appliance has been designed and manufactured

in compliance with international safety standards. The

following warnings are provided for safety reasons and

must be read carefully.

hob, for example plastic and aluminium objects, or

products with a high sugar content. Be especially

careful when using plastic film and aluminium foil or

packaging: if placed on surfaces which are still hot,

they may cause serious damage to the hob.

This appliance conforms to the following

European Economic Community directives:

• Always make sure that pan handles are turned

towards the centre of the hob in order to avoid

accidental burns.

- 2006/95/EEC dated 12/12/06 (Low Voltage) and

subsequent amendments;

- 2004/108/EEC dated 15/12/04 (Electromagnetic

Compatibility) and subsequent amendments;

- 93/68/EEC dated 22/07/93 and subsequent

amendments.

• When unplugging the appliance, always pull the plug

from the mains socket; do not pull on the cable.

• Never perform any cleaning or maintenance work

without having disconnected the appliance from the

electricity mains.

• The appliance should not be operated by people

(including children) with reduced physical, sensory

or mental capacities, by inexperienced individuals

or by anyone who is not familiar with the product.

These individuals should, at the very least, be

supervised by someone who assumes responsibility

for their safety or receive preliminary instructions

relating to the operation of the appliance.

• Do not look at the halogen lamps in the cooking

zones for long if they are present.

- 1275/2008 stand-by/off mode.

General safety

! Make sure that the air inlet behind the fan grille is

never obstructed. The built-in hob should, in fact, be

provided with suitable ventilation for the cooling of the

electronic components used in the appliance.

• The appliance was designed for domestic use inside

the home and is not intended for commercial or

industrial use.

• The appliance must not be installed outdoors, even

in covered areas. It is extremely dangerous to leave

the appliance exposed to rain and storms.

• Do not let children play with the appliance.

• Do not place metal objects (knives, spoons, pan

lids, etc.) on the hob as they may become hot.

• The appliance is not intended to be operated by

means of an external timer or separate remote-

control system.

• Do not touch the appliance when barefoot or with

wet or damp hands and feet.

• The appliance must be used by adults only for

the preparation of food, in accordance with the

instructions outlined in this booklet. Any other

use of the appliance (e.g. for heating the room)

constitutes improper use and is dangerous.

The manufacturer may not be held liable for any

damage resulting from improper, incorrect and

unreasonable use of the appliance.

Disposal

• When disposing of packaging material: observe

local legislation so that the packaging may be

reused.

• The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states

that household appliances should not be disposed of

using the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order

to optimise the cost of re-using and recycling the

materials inside the machine, while preventing

potential damage to the atmosphere and to public

health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations

regarding separated waste collection.

• The glass ceramic hob is resistant to mechanical

shocks, but it may crack (or even break) if hit with

a sharp object such as a tool. If this happens,

disconnect the appliance from the electricity mains

immediately and contact a Service Centre.

• Ensure that power supply cables of other electrical

appliances do not come into contact with the hot

parts of the hob.

• Remember that the cooking zones remain relatively

hot for at least thirty minutes after they have been

switched off. An indicator light provides a warning

when residual heat is present (see Start-up and use).

• Keep any object which could melt away from the

For further information relating to the correct disposal

of exhausted household appliances, owners may

contact the public service provided or their local

dealer.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Care and maintenance

Stainless steel frame (only in models with outer frame)

Switching the appliance off

Stainless steel can be marked by hard water which has

been left on the surface for a long time, or by cleaning

products containing phosphorus.

Disconnect your appliance from the electricity supply

before carrying out any work on it.

After cleaning, it is advisable to rinse the surface well

and dry it thoroughly. If water is spilt on the surface,

dry it quickly and thoroughly.

Cleaning the appliance

! Do not use abrasive or corrosive detergents

! Some hobs have an aluminium frame which is

similar to stainless steel. Do not use any cleaning or

degreasing products which are not suitable for use

with aluminium.

(for example, products in spray cans for cleaning

barbecues and ovens), stain removers, anti-rust

products, powder detergents or sponges with abrasive

surfaces: these may scratch the surface beyond repair.

! Never use steam cleaners or pressure cleaners on the

Disassembling the hob

appliance.

If it is necessary to disassemble the hob:

1. Loosen the screws fixing the alignment springs on

each side.

• It is usually sufficient simply to wash the hob using

a damp sponge and dry it with absorbent kitchen

towel.

2. Loosen the screws holding the fixing hooks in each

corner.

3. Take the hob out of its installation cavity.

• If the hob is particularly dirty, rub it with a special

glass ceramic cleaning product, then rinse well and

dry thoroughly.

! Do not attempt to repair the appliance yourself. If the

appliance breaks down, contact a Service Centre.

• To remove more stubborn dirt, use a suitable

scraper. Remove spills as soon as possible, without

waiting for the appliance to cool, to avoid residues

forming crusty deposits. You can achieve excellent

results by using a rust-proof steel wire sponge -

specifically designed for glass ceramic surfaces -

soaked in soapy water.

• If any plastic or sugary substances are accidentally

melted on the hob, remove them immediately with

the scraper, while the surface is still hot.

• Once it is clean, the hob may be treated with

a special protective maintenance product: the

invisible film left by this product protects the surface

from drips during cooking. This maintenance task

should be carried out while the appliance is warm

(not hot) or cold.

• Always remember to rinse the appliance well with

clean water and dry it thoroughly: residues can

become encrusted during subsequent cooking

processes.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Technical description of

the models

This table provides a model-by-model list of the energy absorption values, type of heating elements and diameters of

each cooking zone.

Key:

H = single hilight

DH = double hilight

Hobs

Cooking zone

Back Left

Back Right

Front Left

Front Right

Total power

CIS 644 DD Z S

Power (W)

I 1400 – B 2000* – 600 if Front Left*

I 2200 – B 3000* - 1600 if Front Right*

I 2200 – B 3000* - 1600 if Back Left*

I 1400 – B 2000* – 600 if Back Right*

7200

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Guarantee

12 months Parts and Labour Guarantee

Your appliance has the beneﬁt of our manufacturer’s guarantee, which covers the cost of breakdown repairs for

twelve months from the date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either

workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.

This guarantee is subject to the following conditions:

The appliance has been installed and operated correctly and in accordance with our operating and

maintenance instructions.

The appliance is used only on the electricity or gas supply printed on the rating plate.

The appliance has been used for normal domestic purposes only.

The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by

any person not authorised by us.

Any repair work must be undertaken by us or our appointed agent.

Any parts removed during repair work or any appliance that is replaced become our property.

The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

Damage resulting from transportation, improper use, neglect or interference or as a result of improper

installation.

Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,

batteries, light bulbs, ﬂuorescent tubes and starters, covers and ﬁlters.

Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-

DOMESTIC PREMISES.

5 Year Parts Guarantee

Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering

your appliance with us and the parts being ﬁtted by one of our authorised engineers. There will be a charge for

our engineer’s time. To activate the extra parts warranty on your appliance, simply call our registration line on

08448 24 24 24 (Republic of Ireland 01 230 0800)

Extended Guarantees

We offer a selection of protection plans that enable you to fully cover yourself against the expense of repair bills

for the life of your policy. To ﬁnd the ideal plan for you please call our advice line on 08448 226 226 (Republic of

Ireland 01 230 0233).

Free Helpdesk Service

We have a dedicated team who can provide free advice and assistance with your appliance if you experience

any technical difﬁculties within the ﬁrst 90 days of ownership. Simply call our Hotpoint Service Hotline on 08448

224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an

engineer to call.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Download from Www.Somanuals.com. All Manuals Search And Download.

04/2012- 195101115.00

XEROX FABRIANO

After Sales Service

No one is better placed to care for your Hotpoint appliance during the course of its working life than us – the

manufacturer.

Essential Contact Information

Hotpoint Service

We are the largest service team in the country offering you access to 400 skilled telephone advisors and 1000

fully qualiﬁed engineers on call to ensure you receive fast, reliable, local service.

UK: 08448 224 224

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Please note: Our advisors will require the following information:

Model number:

Serial number:

Parts and Accessories

We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically

clean your appliance to keep it looking good and functioning efﬁciently throughout its life.

UK: 08448 225 225

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Appliance Registration

We want to give you additional beneﬁts of Hotpoint ownership. To activate your free 5 year parts guarantee you

must register your appliance with us.

UK: 08448 24 24 24

Republic of Ireland: 01 230 0800

www.hotpointservice.co.uk

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB

Indesit Company Unit 49 Airways Industrial Estate, Dublin 17

Recycling and Disposal Information

As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves the right to use

quality, recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the

door, plug, and cut the mains cable off ﬂush with the appliance. Dispose of these parts separately to ensure that

the appliance can no longer be plugged into mains socket, and the door cannot be locked shut.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Grizzly Lathe G4015Z User Manual
Harbor Freight Tools Portable Generator 94192 User Manual
Honeywell Air Cleaner HHT 080 User Manual
Honeywell Thermostat V8043 User Manual
Hotpoint Clothes Dryer TCFM 70C Futura User Manual
HP Hewlett Packard Computer Accessories E200 User Manual
HP Hewlett Packard Computer Accessories J8694A User Manual
HP Hewlett Packard Tablet FB359UA User Manual
Hunter Fan Fan 90245 User Manual
iHome MP3 Docking Station iH30 User Manual