1
2
3
4
5
6
7
OFFMANAUTO
CMR707A1049 - User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING-UP THE CMR707
‘Getting Started’
This section shows you how to setup and run the thermostat in 3 simple steps:
STEP 1: Installing the Batteries
Note: if the ‘Low Battery’ Indicator
is showing or the thermostat screen is blank (no symbols
or digits are displayed) replace the batteries as follows, otherwise, please go directly to Step 2:
Setting the Date and Time.
To install the Batteries:
a. Lift up the front cover of the thermostat to reveal the battery cover and product controls.
b. Remove the battery cover by pressing down and sliding out.
c. Insert the 2 x AA LR6 Alkaline Batteries supplied with the thermostat, ensuring the correct
orientation (see ‘Controls Layout’ on page 2).
d. After a short pause the thermostat will display information on the screen and is now ready for use.
e. Replace the battery cover by sliding it firmly back into the front of the thermostat.
PLEASE RESPECT YOUR ENVIRONMENT! Take care to dispose of used batteries carefully.
STEP 2: Setting the Day and Time
To set the Day and Time:
a. Press the DAY button once and the ‘day indicator’ will begin to flash.
b. Press the DAY button until the correct day is reached (Day 1 = Monday). Press the green
button to confirm.
d. Press either of the
the time digits (when the unit is powered for the first time the display shows 12:00).
e. Use the or buttons to set the correct time then press the green button to confirm.
or buttons once to enter time setting mode. The LCD screen flashes
Each press of the buttons will change the time by one minute and holding them down will
change the time slowly at first and get progressively quicker.
Note: If this mode is entered accidentally then press the AUTO, MAN or OFF buttons to exit.
STEP 3: Running the Built-in Heating Program
The thermostat is now ready for operation. Press the AUTO button and the built-in heating program will start
running. Note: The built-in heating program has been designed to provide normal comfort requirements,
but if you want to customise the settings please see the next section ‘Programming the CMR707’.
PROGRAMMING THE CMR707
The Built-in Heating Program
‘Efficient Daily Use’
The built-in heating program has 4 temperature level changes per day that can be set between
3.00am and 2.50am the following day - allowing you to maintain the evening temperature after
midnight. Each temperature level can be set between 5°C and 35°C, and adjusted in 0.5°C
increments. The factory default program for heating is as follows.
Monday to Friday
Period
1
2
3
4
(Day 1 to 5)
Time
6:30
21°C
8:00
18°C
18:00
21°C
22:30
16°C
Temperature
Saturday & Sunday
Period
1
2
3
4
(Day 6 & 7)
Time
8:00
21°C
10:00
21°C
18:00
21°C
23:00
16°C
Temperature
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
‘Efficient Daily Use’
PROGRAMMING THE CMR707
You now have a choice of how to set the
program for the next day:
Reviewing the Heating Program
To review or edit the heating program use
f. i) Press the COPY DAY button to copy
Monday’s program into Tuesday. The display
will go blank apart from the ‘non flashing’
day indicator, which indicates the day
copied and the ‘flashing’ target day to copy
the program to. To accept this day press the
the PROGRAM
or
buttons to navigate
between the 4 individual programming periods
for that day. Use the DAY button to step through
each day of the week, so the complete 7 day
heating program can be reviewed or edited.
green
button. To select a different target
Modifying the Heating Program
To change the heating program:
a. Press either of the PROGRAM
buttons to enter the programming mode.
The time / temperature settings for period
day press the DAY button until the ‘flashing’
day indicator is under the required day, then
accept it by pressing the green
Note: Once the target day is confirmed it
becomes the day that is copied if the COPY
DAY button is pressed again.
or
button.
ꢀ
on Monday (Day 1) will be flashing as
shown. The active period is highlighted by
a flashing square around the numbers at the
bottom of the screen and the selected day
is shown with the day indicator.
OR
ii) Press the DAY button to move the day
indicator to Tuesday (Day 2). The program
for that day can then be adjusted by following
steps b to e. Programs for the remaining days
can be set in the same way, using the DAY
button to move to the next day.
1
2
3
4
5
6
7
To exit the programming mode select the
desired operating mode by pressing the
AUTO, MAN or OFF buttons. Note: To run the
adjusted program select the AUTO mode.
ꢀ
ꢁ
ꢂ
4
b. To adjust the period start time use the
or buttons, the ‘OK?’ indicator will be
displayed to confirm the change. Holding the
button down will change the time quickly.
Disabling / Enabling Time Periods
The thermostat has 4 periods each day that
can be programmed, but you may not need
all of these switch points for your heating
requirements. Therefore, any period from
to 4 can be removed from (or returned to) the
heating program profile.
Note: If you are pressing the
or
buttons and the display flashes the next
period, it means the next period will be
pushed forward.
2
c. Once the required time is reached press
the green
button to confirm.
To disable or enable time periods:
Note: If the original time setting did not
require adjustment press the green
button to move to step ‘d’.
a. To disable unwanted periods go to the
desired period ( ꢁ to 4 )
PROGRAM or buttons to navigate,
using the
ensure the correct period is highlighted
with the flashing square symbol. Press and
d. The temperature setting for period
Monday (Day 1) will now be flashing. To
adjust this press the or buttons and
confirm the setting again by pressing the
green button.
ꢀ
on
hold the
button for at least 2 seconds
and the display will indicate the period has
been removed from the program.
b. To enable periods again follow the same
procedure as above, navigating to the
already disabled period. To enable this
e. The next time and temperature period will
now be active. Adjust this by repeating
steps b - d above until all 4 periods are set
for Monday or press the AUTO button to
run the program as set, at any time.
period again press and hold the
button
for at least 2 seconds.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE CMR707
‘Using the Features’
Using the Special Functions
Choosing the Operating Mode
The thermostat can operate in three different
modes: Automatic, Manual or Off. To set the
operating mode press either of the AUTO,
MAN or OFF buttons. The screen indicates
which mode is currently active by displaying
AUTO, MAN or OFF.
•
HOLIDAY Function
The holiday function allows you to set a
constant temperature (default 10°C)
for specified number of days (from
- 99 days). This lets you save energy and
related costs when you are away from
home, but resumes normal operation on
the day of your return.
=
a
1
•
•
•
AUTO (automatic) mode sets the
thermostat to follow the built-in temperature
program
Operating the thermostat in this mode is
the best way to maintain high level of
(default
or
personalised).
To set the Holiday function:
a. Ensure the thermostat is running in
AUTO or MAN operating modes.
a
temperature comfort whilst maximising your
energy savings.
b. Press the holiday
button to
display the holiday days counter and
temperature setting, along with the
MAN (manual) mode sets the thermostat
to act as
a
simple thermostat with
a
fixed
holiday indicator
c. Press the or
the holiday time (1 - 99 days) and press
.
setpoint throughout the day. The setpoint can
be adjusted from 5°C to 35°C by using the
time buttons to set
or
buttons. The thermostat will continue
to maintain this temperature until another
operating mode or temperature is selected.
the green
button to confirm.
d. Press the
or buttons to set the
OFF mode sets the thermostat to control
to a minimum temperature setting of 5°C
holiday temperature (5°C - 35°C) and
press the green button to confirm.
(default) that acts as
measure for your home.
a
frost protection
The thermostat will now control to the new
temperature for the set number of days that
your home is vacant. At midnight the holiday
counter will be reduced by one until the
selected number of days have passed. The
thermostat will then return to normal operation
as set by the MAN or AUTO mode. To cancel
the HOLIDAY function or to exit the function at
During Normal Operation
•
Temperature Enquiry
In AUTO, MAN and OFF operating
modes the thermostat will display the
current room temperature. To review the
programmed ‘target’ temperature (the
temperature which the thermostat is trying
any time press the
button a second time.
Adjusting the Time
to maintain) press the
button. This
‘target’ temperature value will be displayed
flashing for 5 seconds before returning to
the current room temperature value.
To adjust only the time during normal
operation use the
or
buttons to adjust
button again
the time and press the green
to confirm any changes.
•
Temperature Override
During normal operation (AUTO mode) the
programmed temperature can be adjusted
manually by pressing the
or the button. The ‘target’ temperature
will be displayed and flash for 5 seconds
- during this time the or buttons can
or buttons
be used to modify the set value. Note: This
temperature override is cancelled at the
next programmed temperature change.
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING THE CMR707
Symptom
Remedy
Blank Display (Power Loss).
Check batteries are installed by removing the battery
cover.
Check batteries have been installed in the correct
orientation.
Replace the batteries.
Display shows flashing
symbol.
The batteries in the thermostat are low on power
- Replace the batteries.
Display shows
symbol.
A fault has occurred in your heating system. Remove
and re-insert the batteries.
If the
symbol does not clear after a few minutes
contact your installer.
When setting my program the
following is displayed --:-- --.-
The time period has been disabled, to enable see
‘Disabling / Enabling Time Periods’ on page 4
The symbol is displayed but the
boiler is not firing.
This may be due to the internal controls of the boiler.
FAQ’s
How do I set one temperature for the
How do I change the batteries on the
thermostat when they run out?
whole day?
The thermostat constantly monitors the battery
To operate as a simple thermostat with one
temperature throughout the day, select the
manual operating mode by pressing the
MAN button. Adjust the temperature by
power level, which typically lasts for about
years before needing replaced. When the power
is running low flashing symbol will be
2
a
displayed on the screen. To change the batteries
follow the steps in the above section (‘STEP 1:
Installing the Batteries’ on page 3), replacing
the used batteries with new ones in Step c.
Note: While changing the batteries your program
settings will be stored but you may need to adjust
the time settings to be correct.
pressing the
or
buttons - this can be
set anywhere from 5°C to 35°C in 0.5°C steps.
The thermostat will continue to maintain this
temperature until another operating mode is
selected or the temperature is adjusted.
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS A PROGRAMMABLE ROOM THERMOSTAT?
...an explanation for householders
A programmable room thermostat is both a programmer and a room thermostat. A programmer
allows you to set ‘On’ and ‘Off’ time periods to suit your own lifestyle. A room thermostat works
by sensing the air temperature, switching on the heating when the air temperature falls below the
thermostat setting, and switching it off once this set temperature has been reached.
So, a programmable room thermostat lets you choose what times you want the heating to be on,
and what temperature it should reach while it is on. It will allow you to select different temperatures
in your home at different times of the day (and days of the week) to meet your particular needs.
Turning a programmable room thermostat to a higher setting will not make the room heat up any
faster. How quickly the room heats up depends on the design of the heating system, for example,
the size of boiler and radiators.
Neither does the setting affect how quickly the room cools down. Turning a programmable room
thermostat to a lower setting will result in the room being controlled at a lower temperature, and
saves energy.
The way to set and use your programmable room thermostat is to find the lowest temperature
settings that you are comfortable with at the different times you have chosen, and then leave it
alone to do its job. The best way to do this is to set low temperatures first, say 18°C, and then turn
them up by one degree each day until you are comfortable with the temperatures. You won’t have
to adjust the thermostat further. Any adjustments above these settings will waste energy and cost
you more money.
If your heating system is a boiler with radiators, there will usually be only one programmable room
thermostat to control the whole house. But you can have different temperatures in individual rooms
by installing thermostatic radiator valves (TRVs) on individual radiators. If you don’t have TRVs,
you should choose a temperature that is reasonable for the whole house. If you do have TRVs, you
can choose a slightly higher setting to make sure that even the coldest room is comfortable, then
prevent any overheating in other rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have to be adjusted in spring and
autumn at the changes between Greenwich Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for example, ‘Override’, ‘Advance’
or ‘Boost’. These are explained in the manufacturer’s instructions.
Programmable room thermostats need a free flow of air to sense the temperature, so they must
not be covered by curtains or blocked by furniture. Nearby electric fires, televisions, wall or table
lamps may prevent the thermostat from working properly.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
42010941-008 R1
© 2006 Honeywell International Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|