Operating Manual
TM
UtilityPRO Series
Touchscreen Programmable Demand Control Thermostat
85-3126
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Replacement
Battery Cover
Assembly
The UtilityPRO has a coin cell
battery that retains the time
and date during a power failure.
Under normal circumstances the
coin cell should last five years.
Should the time and date need
to be reset after a power failure,
this is an indication that the coin
cell needs to be replaced. You
should replace battery every five
years, or before leaving home for
an extended period.
Coin cell
battery tray
Insert the coin cell battery in the coin cell battery
tray and push it inside the battery cover assembly
The UtilityPRO is shipped from the factory with the coin cell installed. To keep the
battery from discharging during shipment and storage, the UtilityPRO is shipped
from the factory with a plastic tab inserted in the battery holder. This tab must be
removed before the thermostat is mounted on the wall. Simply pull the plastic tab
out of the thermostat. To replace the battery, remove the battery tray using a screw
driver. Place a new coin cell (type CR2032 or equivalent) observing the correct
polarity and push the battery tray into the battery cover assembly.
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Part 15 Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Class B limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is not guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient the receiving antenna.
• Increase the distance between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the installer or an experienced radio/TV technician for help.
Industry Canada Requirements
Operation of this device is subject to the following two conditions:
1) This device may not cause interference.
2) This device must accept any interference, including interference that may cause undesired operation of the device.
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
UtilityPRO Series
Table of contents
Special Features ......................................17
Screen Lock .............................................18
Screen Cleaning.......................................19
Advanced Functions...........................20-23
Troubleshooting ..................................24-25
About your new thermostat
Thermostat Features..................................2
Getting Started
Quick Reference to Controls.....................3
Quick Reference to Status Display...........4
Subscription Services
Demand Control.........................................5
Utility Usages.............................................6
Utility Messages.........................................6
View Message............................................7
Usage & Billing...........................................8
This thermostat is ready to go!
Your new thermostat is pre-
programmed and ready to go.
See page 15 to check settings.
Settings
Fan Settings ...............................................9
System Settings.......................................10
Schedule Settings....................................11
Program Schedule Override (Temp)........12
Schedule Override (Permanent)..............13
Clock Settings..........................................14
CAUTION: EQUIPMENT DAMAGE
HAZARD. To prevent possible
compressor damage, do not
operate cooling system when
outdoor
Programming & Operation
Program Schedules ............................15-16
temperature is below 50aF (10aC).
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual
TM
UtilityPro Features
Congratulations! You’ve just purchased the world’s most advanced, easy-to-use
thermostat. It has been designed to give you many years of reliable service and
touchscreen climate control.
Features
• Provides Utility information messages.
• Provides Utility billing information.
• 5/1/1 and 5/2-day program schedules maximize comfort and economy.
• Demand response thermostat programmed to aid you in your savings.
®
• EnergyStar compliant to greatly reduce your heating/cooling expenses.
• One-touch temp control overrides program schedule at any time.
• Precise comfort control keeps temperature within 1°F of the level you set.
• Provides demand control messages.
• Large touchscreen display with backlight, is easy to read—even in the dark.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
UtilityPRO Series
Quick Reference to Controls
Press day(s) to set program schedule (see page 11)
Press to view
messages
Displays the current
tier rate
Press to adjust
temperature settings
Press to select fan
operation
Press to select system
type
Press to view the
subscribed service
messages
SUN
Press to set program
schedule
Press to lock keypad for 30
seconds to clean screen
Press to override
program schedule
Press to set clock
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual
Quick Reference to Status Display
Current inside temperature
Temperature setting
TIER
VIEW
MEDIUM
Fan setting
Inside
S7et T0o
Program schedule ON
(does not display
when off)
FAN
AUTO
75
Following
Schedule
System setting
SUN
SYSTEM
AM
Recovery
8:10
HEAT
Adaptive Intelligent
Recovery in effect
(see page 17)
SCHED
HOLD CLOCK SCREEN USAGE
Current time
Other display messages:
• Cool ON: Cooling system is activated
Current day of week
• Heat ON: Heating system is activated
• Aux Heat ON: Auxiliary heating system is activated
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
UtilityPRO Series
Demand Control
This is an energy saving device. At times, thermostat operation may be temporarily adjusted
by a small amount as outlined in your energy provider’s associated program literature. This is
normal operation and is part of the program for which you have enrolled.
Thank you for your participation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual
®
UtilityPUrsoagFeesatures
Usage is a service provided by the utility provider. Depending on the various services
provided by the utility provider, Usage may contain vital information for your use. It
may display your electricity bill, water consumption bill, gas bill, and so on. Usage
also has a feature wherein you can compare your present consumption against
your last year’s consumption for the same time period. For example, it displays
your current electricity bill along with the previous year’s electricity bill for the same
month.
Usage also displays the rate of electricity at peak times and off peak times. Thus you
can adjust your electricity consumption accordingly.
Utility Messages
Messages are also a part of the services provided by the service utility provider.
Messages are sent by the service provider to assist you with additional information.
These messages may contain weather warnings, greetings, reminders, information
about discounts running at a shop, system maintenance messages, and so on.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
UtilityPRO Series
GVieetwtinMgeSstsaargteds
Press
on your screen.
Good Morning!
The message icon blinks when you
receive a new message.
The Message screen appears.
Use the arrow buttons to view the
messages. There can be a maximum
of five messages. The message
scrolls automatically if it has more
than 21 characters.
In case there are no messages, the
message icon does not appear.
EXIT
Press Delete to delete the displayed
message.
Press Exit to go to the main screen.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual
TM
UtsialigtyeParnod FBeilalitnugres
Press
on your screen.
ELECTRICITY BILL
The Usage screen appears. Navigate
using the arrow buttons to view the
billing consumption of water, gas,
electricity, and so on*.
$
$
52
61
In case there are no utility
messages, the utility message icon
does not appear.
EXIT
Press Exit to go to the main screen.
* subject to Contract Agreement with
the Utility Provider.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
UtilityPRO Series
®
GUFateintlittSiynePgtrtoSintagFrsetaetdures
Press FAN to select fan operation, then press
DONE.
Inside
Set To
• ON: Fan is always on.
FAN
70
70
AUTO
• Auto: Fan runs only when the heating or
Following
cooling system is ON.
SYSTEM
WED
Schedule
AM
HEAT
6:01
SCHED
• Circ: Fan runs randomly, about 35% of the
time, not counting any run time with the
heating or cooling system.
HOLD CLOCK SCREEN USAGE
You can press FAN to override the fan settings
you’ve programmed for different time periods.
If you select ON or Circ, the setting you select
remains active until you press FAN again to
select Auto.
Press FAN
Note: If a fan schedule is programmed,
“Auto” runs the fan schedule.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual
System Settings
Press the SYSTEM button to select one of the
following, then press DONE.
• Heat: Thermostat controls only the
heating system.
Inside
Set To
FAN
• Cool: Thermostat controls only the
cooling system.
70
AUTO
70
6:01
SCHED
• Off: Heating and cooling systems are
SYSTEM
Following
Schedule
OFF.
WED
AM
HEAT
• Auto: Thermostat automatically selects
heating or cooling depending on the
indoor temperature.
HOLD CLOCK SCREEN USAGE
• Em Heat (only for heat pumps with
auxiliary heat): Thermostat controls
Emergency and Auxiliary Heat.
Press SYSTEM
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
UtilityPRO Series
Schedule Settings
Press SCHED
1. Press SCHED, then EDIT.
SCHED
HOLD CLOCK SCREEN USAGE
2. Press day buttons to select day(s). There
are three groups (MON-FRI), (SAT), and (SUN).
3. Press ꢀꢁor ꢂꢁto set Wake time for selected
Press EDIT
day(s).
4. Press ꢀꢁor ꢂꢁto set Heat and Cool
DONE
EDIT
WAKE
LEAVE RETURN SLEEP CANCEL
Set heat/cool levels
EDIT SCHEDULE
temperature for this time period.
Select day(s)
5. Press other time periods (LEAVE, RETURN,
SLEEP) to set time and temperatures for
each.
SET SCHEDULE
SAT
6. Press DONE to save & exit (or press CANCEL
SUN
MON-FRI
HEAT
to exit without saving changes).
70
CANCEL
PERIOD
Note: You can press CANCEL PERIOD to eliminate any
unwanted time period.
AM
COOL
78
Note: Press FAN to customize fan settings for any
time period.
6:00
DONE
WAKE
LEAVE RETURN SLEEP CANCEL
Set time for program
period to start
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual
Program Schedule Override (Temporary)
Adjust temperature
Press ꢀꢁor ꢂꢁto immediately adjust the
temperature. This temporarily overrides the
temperature setting for the current time period.
The new temperature is maintained only until
the next programmed time period begins
(see page 15). For example, if you want to
turn up the heat early in the morning, it will
automatically be lowered later, when you leave
for the day.
Inside
Set To
FAN
73
70
AUTO
Heat On
SYSTEM
FRI
AM
HEAT
8:00
HOLD
To cancel the temporary setting at any time,
press CANCEL (or SCHED). The program schedule
resumes.
SCHED
CLOCK SCREEN USAGE
CANCEL
Press to set timer
Press CANCEL (or SCHED) to
resume program schedule
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
UtilityPRO Series
Program Schedule Override (Permanent)
Adjust temperature
Press HOLD to permanently adjust the
temperature. This turns off the program
schedule.
Whatever temperature you set is maintained
24 hours a day until you manually change it or
press CANCEL (or SCHED) to cancel “Hold” and
resume the program schedule.
Inside
Set To
FAN
73
70
AUTO
Heat On
Permanent
Hold
SYSTEM
FRI
AM
HEAT
8:00
HOLD
SCHED
CLOCK SCREEN USAGE
CANCEL
Press CANCEL (or SCHED) to
resume program schedule
Press HOLD
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual
Clock Settings
Press CLOCK
To set the current time display, press CLOCK,
then press ꢀꢁor ꢂꢁto adjust the time. Press
and hold ꢀꢁor ꢂꢁto advance the time more
quickly.
WED
AM
6:01
SCHED
Press DONE to save & exit (or press CANCEL to
HOLD CLOCK SCREEN MORE
exit without changing the time).
Adjust time, then press DONE
Note: The real-time clock should never require
adjustment since it automatically updates for
daylight savings time, and stores all date/time
information.
WED
AM
6:02
Note: To change the current week day display, see
page 21.
DONE
CANCEL
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
UtilityPRO Series
Save Money by Setting Program Schedules
It is easy to program your system for maximum energy savings. You can program four
time periods each day, with different settings for weekdays and weekends.
WAKE
Set to the time you awaken and the temperature you want
during the morning, until you leave for the day.
67:000 am°
LEAVE
Set to the time you leave home and the temperature you
want while you are away (usually an energy-saving level).
86:020 am°
RETURN
Set to the time you return home and the temperature you
want during the evening, until bedtime.
67:000 pm°
SLEEP
Set to the time you go to bed and the temperature you want
overnight (usually an energy-saving level).
160:200 p°m
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual
®
EnergyStar Settings for Maximum Cost Savings
®
This thermostat is pre-set to use EnergyStar program settings. We recommend these
settings, since they can reduce your heating/cooling expenses by as much as 33%.
Heat (Mon-Fri) Cool (Mon-Fri) Heat (Sat-Sun) Cool (Sat-Sun)
Wake
70 °
62 °
70 °
62 °
78 °
85 °
78 °
82 °
70 °
62 °
70 °
62 °
78 °
85 °
78 °
82 °
(6:00 am)
Leave
(8:00 am)
Return
(6:00 pm)
Sleep
(10:00 pm)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
UtilityPRO Series
Special Features
Auto Changeover: When set to Auto, the thermostat automatically selects heating or
cooling depending on the indoor temperature.
Adaptive Intelligent Recovery: This feature allows the thermostat to “learn” how
long the furnace and air conditioner take to reach programmed temperature settings,
so the temperature is reached at the time you set. For example: Set the Wake
time to 6 am, and the temperature to 70°. The heat comes on before 6 am, so the
temperature is 70° by the time you wake at 6. The message “Recovery” is displayed
when the system is activated before a scheduled time period.
Compressor Protection: This feature forces the compressor to wait a few minutes
before restarting, to prevent equipment damage. During the wait time, the message
“Wait” is displayed on screen.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual
Screen Lock
To prevent tampering, the screen can be
partially or fully locked.
WED
SCREEN LOCKED
FAN
Inside
Set To
When partially locked, the screen displays
SCREEN LOCKED for several seconds if a locked
key is pressed. To unlock the screen, press any
unlocked key while SCREEN LOCKED appears on
the screen.
AUTO
70
70
Following
Schedule
SYSTEM
HEAT
PM
6:00
SCHED
When the screen is fully locked, no keys
function. To lock or unlock the screen, see
advanced function 0670 on page 23.
HOLD CLOCK SCREEN MORE
See advanced function
0670 (page 23) for
screen lock options
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
UtilityPRO Series
Screen Cleaning
Press SCREEN
Press SCREEN to go to the cleaning screen.
Press OK to lock the screen for cleaning. The
screen remains locked for 30 seconds so you
can clean the screen without disturbing any
settings.
WED
PM
6:00
SCHED
HOLD CLOCK SCREEN USAGE
After 30 seconds, press CANCEL to resume
normal operation, or press OK if you require
more time for cleaning.
Screen lock timer (30 seconds)
Note: Do not spray any liquid directly on the
thermostat. Spray liquids onto a cloth, then use
the damp cloth to clean the screen. Use water or
household glass cleaner. Avoid abrasive cleansers.
Clean Screen?
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual
Advanced Functions
2. Press and hold
1. Press SYSTEM.
HEAT
SUN
AM
6:01
blank center key
until the display
changes.
DONE
CANCEL
SYSTEM
SUN
Function
Setting
HEAT
3. Change settings as
required (see pages
21-23).
20
0120
DONE
4. Press DONE to exit &
Press ꢀ/ꢂꢁto
Press ꢀ/ꢂꢁto
save changes.
select function
change setting
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
UtilityPRO Series
Advanced Functions
Year setting (first two digits)
Function
0120
Press ꢀ/ꢂꢁto change the first two digits of the year:
Options: 20 = Year 20xx
21 = Year 21xx
Year setting (second two digits)
Function
0130
Press ꢀ/ꢂꢁto change the last two digits of the year:
Options: 01 - 99 (i.e., 2001 - 2099)
Month setting
Function
0140
Press ꢀ/ꢂꢁto change the current month:
Options: 01 - 12 (i.e., January - December)
Date setting
Function
0150
Press ꢀ/ꢂꢁto change the current date:
Options: 01 - 31
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual
Advanced Functions
Program schedule ON/OFF
Function
0160
Press ꢀ/ꢂꢁto turn the program schedule ON or OFF:
Options: 1 5/2 [programmable weekdays and weekends].
2 5/1/1 [weekdays, saturday, and sunday programmable].
Temperature format (°F/°C)
Function
0320
Press ꢀ/ꢂꢁto set the temperature display format:
Options: 0 Fahrenheit
1 Celsius
Daylight savings time ON/OFF
Function
0330
The thermostat is pre-programmed to automatically adjust to daylight savings time.
Press ꢀ/ꢂꢁto select an option:
Options: 0 OFF: No adjustment for daylight savings time
1 ON: Auto-change to daylight savings time (through 2006, and for areas that do
not use the new 2007 DST calendar)
2 ON: Auto-change to daylight savings time (2007 and beyond, for areas that
use the new 2007 DST calendar)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
UtilityPRO Series
Advanced Functions
Program schedule periods
Function
0540
Press ꢀ/ꢂꢁto set the number of program periods:
Options: 4 4-4 program periods (WAKE, LEAVE, RETURN, SLEEP)
2 2-2 program periods (WAKE and SLEEP)
3 3-2 program periods (LEAVE and RETURN)
Clock format
Function
0640
Press ꢀ/ꢂꢁto set the clock display format:
Options: 12 12-hour clock (i.e., “3:30 pm”)
24 24-hour clock (i.e., “15:30”)
Screen lock
Function
0670
Press ꢀ/ꢂꢁto choose a screen lock setting (see page 18):
Options: 0 Screen is unlocked (fully functional)
1 All functions locked except temperature controls and CANCEL key
2 Screen is fully locked
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual
Troubleshooting
If you have difficulty with your thermostat, please try the following.
Most problems can be corrected quickly and easily.
Display is blank
• Check circuit breaker and reset if necessary.
• Make sure power switch at heating & cooling system is ON.
• Make sure furnace door is closed securely.
No response to
key presses (or
temperature
does not
• Check to make sure the thermostat is not locked (see page 18).
• Make sure heating and cooling temperatures are set to acceptable
ranges:
• Heat: 40° to 90°F (4.5° to 32°C)
• Cool: 50° to 99°F (10° to 37°C)
change)
Backlight is dim
• If thermostat is AC powered, a dim display is normal. The backlight
remains ON at a low level, and brightens when a key is pressed.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
UtilityPRO Series
Troubleshooting
Heating or cooling
system does not
respond
• Press SYSTEM to set system to Heat. Make sure the temperature is set
higher than the Inside temperature.
• Press SYSTEM to set system to Cool. Make sure the temperature is set
lower than the Inside temperature.
• Check circuit breaker and reset if necessary.
• Make sure power switch at heating & cooling system is ON.
• Make sure furnace door is closed securely.
• If “Wait” is displayed, the compressor protection timer is ON. Wait
5 minutes for the system to restart safely, without damaging the
compressor.
Display shows Fan • This is normal operation. Auto indicates the thermostat is following the
Auto and ON or
Auto and Circ at
the same time
programmed fan setting. If Auto and ON is shown, the fan is scheduled
for “ON” during this period (see page 9).
Thermostat shows • This indicates that the coin cell battery has drained out. Replace the
the calendar
screen (year,
date, & month)
when the power is
restored.
coin cell battery immediately.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Automation and Control Systems
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
Honeywell Limited-Honeywell Limitée
35 Dynamic Drive
Toronto, Ontario M1V 4Z9
Printed in U.S.A. on recycled
paper containing at least 10%
post-consumer paper fibers.
® U.S. Registered Trademark.
© 2007 Honeywell International Inc.
US Patents pending
85-3126—1 Rev. M.S. 12-07
Download from Www.Somanuals.com. All Manuals Search And Download.
|