C437D,E,F,G,H,J,K and C637B Gas
Pressure Switches
PRODUCT DATA
FEATURES
•
C437 models have direct- and reverse-acting (spst)
switching; C637B has single-pole, double-throw (spdt)
switching.
Pressure ranges: 1/2 to 5-1/2 in. of water (10 to 140 mm
of water, or 0.1 to 1.4 kPa); 1 to 26 in. of water (50 to
700 mm of water, or 0.5 to 7 kPa); 1/2 to 5 psi (300 to
3500 mm of water, or 3 to 35 kPa); 1 to 10 psi (500 to
7000 mm of water, or 5 to 70 kPa).
•
•
•
Models intended for lockout applications must be
manually reset before resuming operation.
Trip-free mechanism on manual reset models ensures
that the limit function of the switch cannot be defeated
by jamming the reset lever.
•
•
•
•
•
•
•
•
•
External manual reset button on side of lockout
models.
Enclosed setting impedes tampering and provides
dust-resistant operation.
Buna-N fiber-reinforced material for increased
strength of control diaphragm.
Two Buna-N fiber-reinforced seal-off diaphragms for
added reliability.
Clear glass cover allows observation of interior
mechanism to aid setting and checkout.
Mercury switch provides visual indication of switch
position.
Heavy die-cast case increases durability and
resistance to corrosion.
Main control diaphragm completely enclosed a leak-
proof chamber can be vented to a safe area.
Models with a pressure range of 1 to 26 in. of water
(50 to 700 mm of water, or 0.5 to 7 kPa) have a
restrictive orifice in the inlet pressure channel to
compensate for momentary surges in gas pressure.
Field-addable orifices of various sizes are available.
Models available with rainproof, dustproof, sleet- and
ice-resistant enclosure; meets NEMA 3R specification.
GENERAL
The C437 and C637 Gas Pressure Switches are pressure-
actuated switching devices used in industrial gas system
applications for safety shutoff, pressure control, and
differential-pressure control.
•
•
Contents
General ...............................................................................
Features ..............................................................................
Specifications ......................................................................
Ordering Information ...........................................................
Recycling Notice .................................................................
Installation ...........................................................................
Setting and Checkout ..........................................................
1
1
2
2
4
4
6
Copyright © 1995 Honeywell Inc.
•
All Rights Reserved
60-2320-9
Download from Www.Somanuals.com. All Manuals Search And Download.
C437D,E,F,G,H,J,K AND C637B GAS PRESSURE SWITCHES
Switch:
Mercury switch (C437F,J and K have two spst switches in one mercury bulb).
Differentials:
Fixed, nominal; measured at pressure indicated:
Pressure Rangea
1/2 to 5-1/2 in.
(10-140 mm, or
0.1-1.4 kPa)
1 to 26 in.b
(50-700 mm, or
0.5-7 kPa)
1/2 to 5 psi
(300-3500 mm, or
3-35 kPa) differential
measurement at
midscale
1 to 10 psi
(500-7000 mm,
or 5-70 kPa)
differential
Differential Measured
at 1/2 in.
differential
measured at 15 in.
measurement
Model
Numbers
in.
mm
kPa
in.
mm
kPa
psi
1/2
1/4
mm
352
176
kPa
3.45
1.72
psi
1c
1/2e 352e 3.45e Additivef
mm
kPa
Typea
C437D,J
—
—
—
1-3/4 44.5 0.44
703c 6.89c Subtractived
C437E,F,H,K
C637B
0.25e 6.4e
0.06e 1-1/4 31.8 0.31
0.15
3.8
0.04
C437G
—
—
—
1-1/4 31.8 0.31
1/4
176
1.72
1/2
352 3.45 Subtractive
a in. = inches of water; mm = millimeters of water.
b Restrictive orifice in inlet pressure channel to compensate for momentary surges in gas pressure.
c Not available for C437J.
d Subtractive models: switching action occurs on pressure rise to the setpoint.
e Not available for C437K.
f
Additive models: switching action occurs on pressure fall to the setpoint.
Pressure Ranges (Scale Range):
Specify one:
MinimumTemperature:
32°F (0°C).
1/2 to 5-1/2 inches of water (10 to 140 mm of water, or
0.1 to 1.4 kPa).
1 to 26 inches of water (50 to 700 mm of water, or 0.5 to
Approvals:
Underwriters Laboratories Inc. Listed: File No. MP2168,
Guide No. MFHX.
7 kPa).
1/2 to 5 lb per sq in. (300 to 3500 mm of water, or 3 to
Canadian Standards Association Certified: File No. 1620,
Guide No. 380-W-1.16.
35 kPa).
1 to 10 lb per sq in. (500 to 7000 mm of water, or 5 to
70 kPa).
Factory Mutual Approved: Report No. 13031-S5 and
19291.
Maximum Sustained Operating Pressure:
Maximum Pressure
Replacement Parts:
106729 Cover Glass, 6 in. (152.4 mm) diameter.
139870A Cover Glass, for rainproof enclosures.
106747 Cover Retaining Ring, for models manufactured
before 1973.
Pressure Range
1/2 to 5-1/2 in. of water
1 to 26 in. of water
1/2 to 5 psi
psi
3.0
kPa
20.7
118733-21 Retaining Clip, for models manufactured since
1975.
5.0
34.5
Accessories:
15.0
30.0
103.4
206.8
4074BWK Bag Assembly: Contains two 137755 Mounting
Brackets and four self-tapping screws: for surface
mounting (standard on C437G and H). Mounting
brackets are shown by dashed lines in Fig. 1.
Field-addable Orifices:
1 to 10 psi
Pipe Connections:
Main or High Pressure: 1/2 in. NPT, female.
Vent or Low Pressure: 1/8 in. NPT, female.
Electrical Wiring: Hole tapped for 1/2 in. conduit.
124674: 0.011 in. (0.28 mm) diameter.
122160: 0.018 in. (0.46 mm) diameter.
Maximum AmbientTemperature:
125°F (52°C).
3
60-2320—9
Download from Www.Somanuals.com. All Manuals Search And Download.
C437D,E,F,G,H,J,K AND C637B GAS PRESSURE SWITCHES
6-1/4 (158.8)
5/16 (7.9) (4)
1
6-1/2
(165.1)
5/8
(15.9)
(4)
7-3/4
(196.9)
7-11/16
DIA.
(195.3)
2
45°
45°
1/8
(3.2)
1
(25.4)
1-5/16
(33.3)
7-3/8 (187.3)
1/8–27 NPT
1/2–14 NPT
TAPPED FOR 1/2 IN.
CONDUIT
2 (50.8)
3-7/16 (87.3)
1
2
137755 MOUNTING BRACKET (2), IN 4074BWK BAG ASSEMBLY – STANDARD
ON C437G AND H; OPTIONAL ON OTHER MODELS.
M7192
VENT TAPPING. REMOVE DUST-SEAL LABEL BEFORE MOUNTING.
Fig. 1. Installation dimensions of the C437 and C637 gas pressure switches, in in. (mm).
INSTALLATION
RECYCLING NOTICE
This control contains mercury in a sealed tube. Do not
place control in the trash at the end of its useful life.
When Installing this Product…
ᕡ Read these instructions carefully. Failure to follow them
could damage the product or cause a hazardous
condition.
If this control is replacing a control that contains
mercury in a sealed tube, do not place your old
control in the trash.
ᕢ Check the ratings given in the instructions and on the
product to make sure the product is suitable for your
application.
ᕣ Installer must be a trained, experienced, flame
safeguard control technician.
ᕤ After installation is complete, check out product
operation as provided in these instructions.
Contact your local waste management authority for
instructions regarding recycling and the proper
disposal of this control, or of an old control containing
mercury in a sealed tube.
60-2320—9
4
Download from Www.Somanuals.com. All Manuals Search And Download.
C437D,E,F,G,H,J,K AND C637B GAS PRESSURE SWITCHES
Use nipple and T for pipe mounting or the mounting
bracket for surface mounting. If a mounting bracket is
used, install the bracket before making piping
connections (standard on C437G and H). Mount the
bracket horizontally with the four 10-24 flathead tapping
screws provided.
CAUTION
Disconnect all power to the pressure switch before
beginning installation to prevent electrical shock and
equipment damage.
ᕤ Level the device carefully.
IMPORTANT
a. Level the device so that the point of leveling
pendulum is aligned with the mark on the inside
of the case.
b. When pipe mounting, install the device at right
angles to the pipe so that it can be leveled by
additional tightening of the pipe fittings.
c. The surface mounting bracket has elongated
holes that allow limited leveling after the mounting
screws are started.
d. Accurate leveling is most essential at very low
pressure settings.
1. Remove the dust-seal label from the vent tapping
before mounting.
2. Accurately level the pressure switch for proper
operation.
3. The C637B pressure switch is a low differential
device. Mount it in a vibration-free location to prevent
chattering.
4. Do not hand tighten the pressure switch by holding
the case.
Follow local codes or ordinances in all cases when different
from these recommendations.
e. If necessary, make arrangements to hold pipe-
mounted units steady and level with bracing.
Fig. 1 shows the mounting dimensions for the C437 and C637
models, and for the accessory mounting bracket (standard on
C437G and H). See Fig. 2 for the individual components.
Location
PENDULUM
Mount the gas pressure switch downstream from the pressure
regulator. Mount low gas pressure switches upstream of any
shutoff valve. Mount high gas pressure switches just
upstream from the burner. When pipe mounting, locate the
device on the portion of the pipe that is most level because
the mercury switch requires level orientation. See step 4 in
the Mounting section.
LEVEL
LINE
MERCURY SWITCH
PRESSURE SETTING
INDICATOR
M7196A
SCALEPLATE
SETTING
SCREW
Fig. 3. Properly leveled C437/637.
UNDER
RETAINER
IMPORTANT
MANUAL
RESET
To avoid leaks and case damage, use a parallel jaw
wrench on the hexagonal part of the case close to
the pipe. Carefully make all connections and test for
leakage. Do not tighten the pressure switch by
holding the case.
BUTTON
(CC437D,
E,J,K)
TERMINAL
STRIP
RETAINER
ᕥ Complete the main piping.
ᕦ Connect the piping to the pressure switch. Select the
application from the following, and proceed as
instructed.
LEVELING
PENDULUM
VENT
TAPPING
(ON SIDE
1
NOT SHOWN)
CONDUIT
TAPPING
a. Hazardous-gas applications: Install a 1/8 in. NPT
pipe at the vent tapping on all hazardous-gas
applications.
MAIN PRESSURE TAPPING
LENS GASKET
(G,H ONLY)
M7630
1
REMOVE DUST-SEAL LABEL BEFORE MOUNTING
WARNING
Fig. 2. Principal parts of the gas pressure switch.
The vent must be installed so that any gas leakage is
vented into a safe place in event of a diaphragm
failure.
Mounting
ᕡ Remove the dust-seal label from the vent tapping.
ᕢ Remove the screws and retainers, and the cover glass.
ᕣ Mount the device on the pipe or nearby vertical surface.
b. Differential-pressure applications:
5
60-2320—9
Download from Www.Somanuals.com. All Manuals Search And Download.
C437D,E,F,G,H,J,K AND C637B GAS PRESSURE SWITCHES
(1) Connect the high-pressure side of the
system to the 1/2 in. NPT main pressure
tapping on the gas pressure switch.
(2) Connect the low pressure side to the 1/8 in.
NPT vent tapping.
RISE
MAKES ON
PRESSURE
FALL
MAKES ON
PRESSURE
RISE
WARNING
TERMINAL
STRIP
No venting is possible in this case. Do not use this
device for differential pressure control with the
hazardous gases.
W
B
1
1
R
R
C437F,J,K
c. Negative-pressure applications: Connect the low
pressure side to the 1/8 in. NPT vent tapping.
1
BOTH ENDS OF THE SWITCH (W-R AND B-R) MUST BE USED
AT THE SAME VOLTAGE IN THE SAME BRANCH CIRCUIT.
M7193
Fig. 5. Wiring diagram for C437F,J,K.
WARNING
This application is for use only with nonhazardous
gases. Do not use this device for negative-pressure
applications with hazardous gases.
RISE
ᕧ Install other controls in the system. Connect wiring, and
complete setting and checkout before replacing the
cover glass and retainers. See Setting and Checkout
section.
MAKES R TO W
ON PRESSURE
RISE
MAKES R TO B
ON PRESSURE
FALL
Wiring
TERMINAL
STRIP
W
B
CAUTION
R
1. Disconnect all power to the pressure switch
before connecting wiring to prevent electrical
shock and equipment damage.
C637B
M7194
Fig. 6. Wiring diagram for C637B.
2. When using a C437F,J, or K, both ends of the
switch (W-R and B-R) must be used at the same
voltage in the same branch circuit.
SETTING AND CHECKOUT
All wiring must comply with local electrical codes, ordinances,
and regulations. Do not exceed the switch ratings given in the
Specifications section.
Setting
In the C437D,G and J models, the differential is subtractive.
The upper operating point is determined by the setpoint, while
the lower operating point is determined by the setpoint minus
the differential. In the C437E,F,H,K and C637B models, the
differential is additive. The lower operating point is determined
by the setpoint, while the upper operating point is determined
by the setpoint plus the differential. Operating points are
shown in Fig. 7.
Wiring diagrams for the different models are shown in Fig. 4,
5 and 6. The switches make or break as indicated in the
diagrams. Connect the wiring to the screw terminals on the
terminal strip after removing the cover glass. Route the wires
through the conduit tapping.
C437D,G: BREAKS ON PRESSURE RISE
C437E,H: BREAKS ON PRESSURE FALL
Remove the retainer and adjust the setpoint for the desired
operating pressure (cutout pressure on a C437D,E,G, or H
spst model) by turning the setting screw (Fig. 2) clockwise
to increase the setpoint and counterclockwise
decrease it.
to
TERMINAL
STRIP
Trip-Free Manual Reset Feature
(C437D,E,J and K only)
M7195
The C437D breaks and the C437J breaks R-B and makes
R-W when the pressure rises to the setpoint. The C437E
breaks, and the C437K breaks R-W and makes R-B when the
pressure falls to the setpoint. None of these pressure
switches will automatically return to their former positions.
Fig. 4. Wiring diagram for C437D,E,G,H.
60-2320—9
6
Download from Www.Somanuals.com. All Manuals Search And Download.
C437D,E,F,G,H,J,K AND C637B GAS PRESSURE SWITCHES
To reset one of these pressure switches, wait until the
pressure falls to the setpoint minus the differential (C437D or
J), or rises to the setpoint plus the differential (C437E or K).
Then depress the manual reset button (Fig. 2) and release it.
The pressure switch will not be reset until you release the
manual reset button. This prevents the switch from becoming
an automatic-reset device if the reset button is stuck, held in,
or tied down.
ᕥ Turn the setting screw toward a high pressure setting
(clockwise
) to simulate a pressure decrease
greater than the differential. The C437G should make
contact and turn on the controlled equipment.
ᕦ Push the manual reset button (Fig. 2) on the C437D or
J; the C437D should make, and the C437J should
break R to W and make R to B.
C437E,F,H,K or C637B
(Additive Differential)
Checkout
Adjust the setpoint for normal operation and check to see that
the gas pressure switch performs as intended. Use a
manometer or accurate pressure gauge connected upstream
from the switch to measure the actual pressure.
ᕡ Put the system into normal operation and gradually
close the upstream gas shutoff valve to cause a
pressure decrease.
ᕢ When the pressure gauge indicates that the pressure is
approximately equal to the setpoint, the C437E or H
should break contact and turn off the controlled
equipment; the C437F,K or C637B should break R to W
and make R to B.
The most likely cause of inaccurate operation is off-level
mounting. Refer to step 4 in the Mounting section and correct
any installation that does not check out satisfactorily.
ᕣ The C437E or K should lock out.
C437D,G or J (Subtractive Differential)
ᕤ Open the gas shutoff valve to increase the pressure
again. When the pressure rises to the setpoint plus the
differential, the C437H should make contact and turn on
the controlled equipment; the C437F or C637B should
break R to B and make R to W.
ᕡ Put the system into normal operation, and set the
pressure switch at the normal setpoint (above the
normal operating pressure).
ᕢ Turn the setting screw (Fig. 2) slowly toward a lower
pressure setting (counterclockwise
pressure increase.
ᕣ When the setpoint is approximately equal to the
pressure indicated on the pressure gauge, the C437D
or G should break contact and turn off the controlled
equipment; the C437J should break R to B and make R
to W.
) to simulate a
ᕥ Push the manual reset button (Fig. 2) on the C437E or
K; the C437E should make, and the C437K should
break R to B and make R to W.
Completing the Installation
ᕡ Remove the pressure gauge or manometer used for
testing. Visually recheck the piping, wiring, and setting.
ᕢ Replace the cover glass and retainers.
ᕤ The C437D or J should lock out.
SET POINT
(SWITCH BREAKS,
ᕣ Return the system pressure to normal.
ᕤ Push the manual reset button (C437D,E,J or K only).
C437D LOCKS OUT)
C437D,G
SUBTRACTIVE
DIFFERENTIAL
PRESSURE
RISE
Installing a Pressure Orifice (Fig. 8)
1
SET POINT MINUS
DIFFERENTIAL (SWITCH MAKES)
To compensate for momentary surges in gas pressure, install
a restrictive orifice in the inlet pressure channel of the
pressure switch. (Refer to Accessories in the Specification
section for the orifice sizes available.)
SET POINT
(BREAKS R-B MAKES R-W
AND LOCKS OUT)
C437J
SUBTRACTIVE
DIFFERENTIAL
PRESSURE
RISE
Align pressure orifice into reset located inside of the main
pressure tapping at the bottom. Press orifice into place using
1/8 in. dowel rod.
1
SET POINT MINUS
DIFFERENTIAL (BREAKS R-W,
MAKES R-B)
SET POINT PLUS
DIFFERENTIAL (SWITCH MAKES)
PRESSURE
FALL
ADDITIVE
2
DIFFERENTIAL
MAIN PRESSURE
TAPPING
C437E,H
SET POINT
(SWITCH BREAKS,
C437E LOCKS OUT)
PRESSURE
ORIFICE
(SELECTED)
SET POINT PLUS
DIFFERENTIAL (BREAKS R-B
MAKES R-W)
PRESSURE
FALL
2
ADDITIVE
C437F,K
C637B
DIFFERENTIAL
SET POINT
(BREAKS R-W, MAKES R-B,
C437K LOCKS OUT)
C437D AND J ARE MANUAL RESET MODELS; THEY CAN BE
MANUALLY RESET WHEN THE PRESSURE FALLS TO THE SET
POINT MINUS THE DIFFERENTIAL.
1
2
M7191A
1/8 IN. DOWEL ROD
Fig. 8. Installing a pressure orifice to compensate for
pressure surges.
C437E AND K ARE MANUAL RESET MODELS; THEY CAN BE
MANUALLY RESET WHEN THE PRESSURE RISES TO THE SET
POINT PLUS THE DIFFERENTIAL.
M7197
Fig. 7. C437 and C637 operating points.
7
60-2320—9
Download from Www.Somanuals.com. All Manuals Search And Download.
Automation and Control Solutions
Honeywell International Inc. Honeywell Limited—Honeywell Limitée
1985 Douglas Drive North
Golden Valley, MN 55422
35 Dynamic Drive
Scarborough, Ontario M1V 4Z9
60-2320—9 L.Z. Rev. 9-95
customer.honeywell.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|