You must be fully aware of all the distinctive
features and precautions related to this
camera before installing it.
DIMENSIONS(mm):
COMPOSITION:
100.0
Guide Pattern
Service Monitor Cable
Operation Manual
Mounting Screw
Series
HD60
130.6
INSTALLATION:
Ceiling
Operation
Stick the guide pattern on the
1
SPECIFICATIONS:
wall or ceiling.
Guide Pattern
Manual
Model
NTSC
PAL
Drill four holes according to
the guide pattern then insert
anchors into the drilled holes.
2
Signal System
NTSC : 525 Lines
PAL : 625 Lines
Scanning System
2 : 1 Interlace
(
(
)
)
Scanning Frequency H
15.734kHz
59.94Hz
15.625kHz
50Hz
Dome Base
Draw out power / video wires
to the connecting places.
3
4
5
•1/3" Sony Super HAD CCD
•380 TV Lines Resolution
•4mm Fixed Lens
•Color Day/Night with 24 LEDs
•Auto White Balance
Scanning Frequency V
Image Sensor
Total / Effective Pixels No.
S/N Ratio
1/3" SONY Super HAD CCD
270K / 250K 320K / 290K
Fixed the camera to a celling
using four screws.
More than 48dB (AGC Off)
380 TV Lines
Resolution
Video Output Level
Lens
Mounting
Screw
Adjust desired focus and scene
by turning and moving the
3-axis camera bracket by hand.
1.0 Vp-p (75 Ohms, composite)
Fixed Lens : f=4.0mm, 81
º
•AGC, BLC, Flickerless On/Off
•Extra Video Output for Installer
•3-Axis Camera Construction
•Diameter of Bubble : 100mm
Focus
Manual
Sync. System
Sensitivity
Electronic Shutter
White Balance
AGC
Internal
Put the dome cover over the
base.
6
7
0 Lux, IR LED
1/60 ~ 100,000 Sec.
1 /50 ~ 100,000 Sec.
Auto
Fix the dome cover on the base
by covering.
On / Off
Dome Cover
BLC
Flickerless
On / Off (with Slide Switch)
On / Off (with Slide Switch)
Power, Video
READ AND KEEP THIS
OPERATION MANUAL
t
Input / Output Connector
Power Consumption
12VDC (10.8V~15V), 0.4A / 5W (Max)
100mm
NOTE
(
)
Ø
Dome Size
Weight
Approx. 366g
Insert coin to the side
hole and remove the
dome cover by twist coin.
Need Help?
Call 1.800.796.CCTV for sales, service and customer support.
90º
Design and specifications are
subject to change without notice.
3-axis
Built-in
camera
PRECAUTIONS:
NAME AND FUNCTION:
bracket makes it much
easier to rotate in any
direction.
360º
Fixed Lens & IR LED Type
!
!
Do not install the camera in
extreme temperature conditions.
Do use the camera under conditions where
temperatures are within -10°C to 45°C.
Be especially careful with ventilation
under high temperatures.
5
CAMERA SET-UP:
4
3
360º
Fixed Lens & IR LED Type
Do not install or use the camera
in an environment where the
humidity is high.
J504
a
Function Selection Switch:
1
2
•FL(Flickerless) ON/OFF
AC24V
It can cause the image quality to be poor.
•
AGC(Auto Gain Control) ON/OFF
b
•BLC(Back Light Compensation)
ON/OFF
b
!
!
!
Do not disassemble the camera.
There are no user-serviceable parts
inside it.
Service Monitor Connecter:
Use service monitor connector
to set camera angle & focus
when installing.
AC 24V
J503
BLC ON
AGC OFF
FL ON
CAUTION : When AGC is off,
D/N does not work because the
D/N switching function is
dependent on the AGC level.
Do not drop the camera or
1
2
3
Tilt rotation: Adjusting the vertical angle.
Pan rotation: Adjusting the horizontal angle.
a
subject them to physical shocks.
It can cause malfunctions to occur.
4
5
IR LED: 850nm / 30°(24EA)
Sensor
Horizontal rotation: Adjusting the horizontal
Camera Lay-out
position of the screen.
Note
TROUBLESHOOTING:
When this camera is installed near
wireless communication devices
that emits strong electromagnetic
field, irregularity such as noise on
the monitor may appear.
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
• Power Consumption: 5W
• IR LED Specification: 850nm / 30°(24EA)
Check the power source for the monitor and camera
The image does not
appear on the screen.
IR LED (4mm Fixed Lens)
and ensure that the voltage and polarity are properly
connected and being supplied correctly.
Check if the lens is stained. If dirty, clean the lens with
a soft, clean cloth.
Adjust the Back Focus of the lens again.
The image on the
screen is dim.
•The wire is polarized. •Use 12VDC power source.
CONNECTION:
Video Output
GND
Video
#
#
1
2
Check if you have connected the camera to a proper
power source and If there is no problem with the power,
turn the unit off immediately and seek assistance from
our Customer Service department.
The camera does not work
properly, the surface of the
camera case is hot, and a black
line appears on the screen.
(Yellow)
No. Function Terminal Color
Remark
Connecting to
Monitor and Power
#1 Video Output
#2 Power Input
Yellow
Red
1.0 Vp-p
Check if the camera is pointed toward the sun or a
fluorescent lamp.
Adjust the angle or location of the camera if too much
light is coming into the screen.
The screen blinks a lot.
Power - 12VDC
(Red)
12VDC(10.8V~15V), 0.4A/5W(Max)
12VDC Power Type
Download from Www.Somanuals.com. All Manuals Search And Download.
|