Honeywell Security Camera HD3VC4SAX User Manual

3 Inch Dome Camera  
HD3VC4SHR/HD3VC4SA/HD3VC4SHRX/HD3VC4SAX  
Operating Conditions  
Figure 4  
Camera Adjustment  
Removing the Dome Cover  
Quick Install Guide  
Avoid viewing very bright objects (example,  
light fixtures) for extended periods.  
Avoid operating or storing the unit in the  
following locations:  
1. Gently turn the dome cover (#5 on  
Figure 2) counter-clockwise to unlock and  
pull free of the housing.  
2. Remove the inner liner (#4) by gently  
pulling it free of the two notches (#2) in the  
housing (#1).  
5
Extremely humid, dusty, hot/cold  
environments (where the operating  
temperature is outside the  
recommended range of 14°F to 122°F  
[-10°C to +50°C])  
1
3. Set the dome (and liner) aside.  
2
3
4
Figure 2  
Dome Cover Removal  
4 — Legend  
Close to sources of powerful  
electromagnetic radiation, such as  
radio or TV transmitters  
Tilt adjustment bracket and thumbnuts (x2)  
for vertical adjustment  
1
Axis ring for horizontal rotation for wall  
mount and tilted ceilings  
1
2
Close to fluorescent lamps or objects  
reflecting light  
Under unstable light sources (may  
cause flickering)  
2
3
4
Zoom lever  
Focus lever  
3
Rotate 3D assembly in base for horizontal  
adjustment  
5
4
Adjusting the Lens  
2 — Legend  
Document 900.0824 - 09/06 - Rev 1.01  
Introduction  
1
Camera housing  
1. Loosen the Zoom lever (#3) counter-  
clockwise a little, then rotate the Zoom  
lever and determine the image view.  
2. Loosen the Focus lever (#4) counter-  
clockwise a little, then adjust the focus for  
optimum picture sharpness.  
2
Notches (x2)  
The unobtrusive, compact design of the  
HD3VC4S Series 3 Inch Dome Camera is ideal  
for indoor installations in commercial and  
residential environments.  
Tilt adjustment bracket  
and thumbnuts  
3
Warnings, Operating Notes  
4
5
Inner liner  
5
Dome cover  
Before You Begin  
Installation and servicing should be performed  
only by qualified and experienced technicians to  
conform to all local codes and to maintain your  
warranty.  
3. Re-tighten the Zoom lever and Focus lever  
after adjustment.  
Connecting the Wiring  
Follow Figure 1 to connect the video output  
connector (a) and 24 VAC/12 VDC power  
connector (b).  
Please read this guide carefully before  
you install the HD3VC4S Series 3 Inch  
Dome Camera. Keep this guide for  
future reference.  
Note  
It is important that you lock the zoom  
and focus levers after making  
WARNING! The use of CSA Certified/UL  
Listed Class 2 power adapters is  
required to ensure compliance  
with electrical safety standards.  
adjustments. This will avoid the  
positions moving (for example, from  
temperature changes or vibrations).  
Caution For DC power supply use, make sure  
the polarity is correct to avoid  
Optional Camera Settings  
See Figure 5 for location on the camera board of  
the camera adjustment functions described  
below.  
Unpack Everything  
malfunction and/or camera damage.  
WARNING! To reduce the risk of fire or  
electric shock, do not expose this  
product to rain or moisture.  
Check that the items received match those listed  
on the order form and packing slip. The  
HD3VC4S Series Camera packing box should  
include, in addition to this Install Guide:  
Mounting the Camera  
WEEE (Waste Electrical and Electronic  
Equipment). Correct disposal of this product  
(applicable in the European Union and other  
European countries with separate collection  
systems). This product should be disposed of,  
at the end of its useful life, as per applicable  
local laws, regulations, and procedures.  
1. Place the mounting template (supplied) on  
the mounting surface and mark the holes  
(see Figure 3).  
2. Drill two holes, then insert the screw  
anchors into the holes.  
3. Secure the camera housing to the wall/  
ceiling with the TP4 x 15 mm tapping  
screws supplied.  
Figure 5  
Camera Adjustment Functions  
3
One fully assembled camera  
One hardware kit  
One 2nd video monitor output cable  
One mounting template  
1
1 : BLC  
2 : AGC  
3 : DC/AES  
4 : LL  
1
2
3
4
LEVEL  
L
H
ON  
OFF  
If any parts are missing or damaged, contact the  
dealer you purchased the camera from or call  
Honeywell Customer Service.  
2
4
MON  
V PHASE  
+
-
1
2
3
4
1:BLC  
2:AG C  
3:DC/AES  
4:LL  
O N  
O FF  
LEVE L  
THIS SYMBOL INDICATES  
THAT DANGEROUS VOLTAGE  
CONSTITUTING A RISK OF  
ELECTRIC SHOCK IS  
H
L
CAUTION  
V
+
PHASE  
-
RISK OF  
Note  
Depending on the material of your  
mounting surface, you may require  
different screws and anchors than  
those supplied.  
ELECTRICSHOCK  
PRESENT WITHIN THE UNIT.  
CAUTION: TO REDUCE THE RISK OF ELECTRIC  
SHOCK, DO NOT REMOVE THE COVER.  
NO USER-SERVICEABLE PARTS INSIDE  
REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL  
THIS SYMBOL INDICATES THAT  
IMPORTANT OPERATING AND  
MAINTENANCE INSTRUCTIONS  
ACCOMPANY THIS UNIT.  
Installation  
Figure 3  
Camera Installation  
The HD3VC4S Series is a fully-integrated  
enclosure with camera and lens.  
1
5
FCC Compliance Statement  
Figure 1  
Camera Parts  
Information to the User: This equipment has  
been tested and found to comply with the limits  
for a Class A digital device. Pursuant to Part 15  
of the FCC Rules, these limits are designed to  
provide reasonable protection against harmful  
interference when the equipment is operated in  
a commercial environment. This equipment  
generates, uses, and can radiate radio  
frequency energy and, if not installed and used  
in accordance with the instruction manual, may  
cause harmful interference to radio  
communications. Operation of this equipment in  
a residential area is likely to cause harmful  
interference in which case the user will be  
required to correct the interference at his own  
expense.  
2
5 — Legend  
b
1
2
3
4
5
LEVEL adjustment pot (Iris level)  
V Phase adjustment pot (24 VAC only)  
Mode setting DIP switches  
Monitor out  
a
M
o
u
n
L
t in  
g
D
T e  
m
p
la t e  
1
o
g
o
i
r
e
c
ti  
o
n
Camera mounting holes  
3
2
Note  
Please use the supplied DC Iris and  
Line lock adjustment tool to adjust  
picture brightness and phase  
adjustment.  
3
4
Picture Brightness Use the LEVEL screw (#1)  
to compensate for the iris level. L (low) makes  
the picture darker. H (high) makes the picture  
brighter.  
5
Caution Changes or modifications not  
expressly approved by the party  
responsible for compliance could void  
the user’s authority to operate the  
equipment.  
1 — Legend  
3 — Legend  
Conduit hole used for surface run power/video  
connector  
1
1
2
3
Screw anchors (x2), supplied  
Mounting template  
TP4 x 15 mm tapping screws (x2) supplied  
Phase Adjustment Use the V Phase  
Adjustment Pot (#2) to adjust the phase  
difference between cameras. Make sure Switch  
4 is ON to activate the Line lock function (AC  
operation only).  
2
3
4
5
a
Camera housing  
Dome cover  
This Class A digital apparatus complies with  
Canadian ICES-003.  
Zoom lever  
Focus lever  
Adjusting the Camera Position  
Video output connector  
DIP Switches Set the DIP switches (#3) to  
activate or deactivate the following functions:  
The HD3VC4S Series camera has three axes for  
positioning the camera. While monitoring the  
picture on the monitor, adjust the camera  
position as follows:  
Manufacturer’s Declaration of  
Conformance  
24 VAC/12 VDC power input connector  
(red +, black -)  
b
The manufacturer declares that the equipment  
supplied with this guide is compliant with the  
essential protection requirements of the EMC  
directive 89/336/EEC and the Low Voltage  
Directive LVD 73/23 EEC, conforming to the  
requirements of standards EN 55022 for  
emissions.  
Switch Description  
1
BLC (Backlight Compensation). Set to ON to  
have the camera adjust the exposure to  
compensate for situations where the subject is lit  
from behind. The factory default setting is OFF.  
Horizontal Adjustment Rotate the 3D  
Note  
See Figure 5 for an explanation of the  
camera board settings.  
assembly in the base. Do not turn the assembly  
more than 360° as this may cause the internal  
cables to twist and disconnect or break.  
2
AGC (Automatic Gain Control). Set to ON  
(default) to have the camera adjust the picture  
for low light conditions.  
Vertical Adjustment After loosening the  
thumbnuts, position the camera as desired, then  
finger-tighten the thumbnuts to set the position.  
3
4
DC/AES Mode. Leave in ON position only.  
Operating Notes  
LL (Line Lock). Set the camera synchronization  
to internal or line lock (line lock is only available  
with 24 VAC). The factory default setting is OFF.  
Power Supply  
This dome camera can operate on 24 VAC  
or 12 VDC.  
Horizontal Rotation For Wall Mount and Tilted  
Ceilings Rotate the lens base (maximum 360°)  
until you are satisfied with the field of view.  
Document 900.0824 - 09/06 - Rev 1.01  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Haier Freezer DW 40L508 User Manual
Harbor Freight Tools Vacuum Cleaner 93245 User Manual
Hasselblad Camera Lens 0 5 User Manual
Honeywell Air Cleaner L4017 User Manual
Hotpoint Dishwasher 51110 User Manual
HP Hewlett Packard Network Card HP IO User Manual
HP Hewlett Packard Scanner HP Snanjet N6350 Networked Document Flatbed Scanner User Manual
Hypertec Carrying Case 5702 User Manual
iHome Clock Radio 97 User Manual
iHome Speaker System IHM60EN User Manual