34-ST-03-57
3/07
ST 3000 Smart Transmitter
Series 900 Remote Diaphragm Seals Models
Specification and
Model Selection
Guide
STR93D
STR94G
0 to 100 psid
0 to 500 psig
0 to 7 bar
0 to 35 bar
Introduction
In 1983, Honeywell introduced the first
Smart Pressure Transmitter― the ST
3000®. In 1989, Honeywell launched
the first all digital, bi-directional protocol
for smart field devices. Today, its
ST 3000 Series 900 Remote Seal
Transmitters continue to bring proven
“smart” technology to a wide spectrum
of pressure measurement applications.
For applications in which the
transmitter must be mounted remotely
from the process, Honeywell offers the
remote seal line of gauge, absolute and
differential pressure transmitters.
Typical applications include level
measurement in pressurized vessels in
the chemical and hydrocarbon
processing industries. A second
application is flow measurement for
slurries and high viscosity fluids in the
chemical industry. Honeywell remote
seal transmitters are available with
secondary fill fluids for corrosive or high
temperature process fluids
Figure 1—Series 900 Remote Seal Pressure Transmitters feature proven
piezoresistive sensors and advanced seal technology with standard weld
connections.
All ST 3000 transmitters can provide a
4-20 mA output, Honeywell Digitally
Enhanced (DE) output, HART* output,
or FOUNDATION™ Fieldbus output.
When digitally integrated with
Honeywell’s Process Knowledge
System™, EXPERION PKS™,
ST 3000 instruments provide a more
accurate process variable as well as
advanced diagnostics.
The devices provide comprehensive self-diagnostics to help users
maintain high uptime, meet regulatory requirements, and attain high
quality standards. S900 transmitters allow smart performance at
analog prices. Accurate, reliable and stable, Series 900 transmitters
offer greater turndown ratio than conventional transmitters.
"Honeywell transmitters operating in the digital mode using
Honeywell's Digitally Enhanced (DE) protocol make diagnostics
available right at the control system's human interface. Equally
important, transmitter status information is continuously displayed to
alert the operator immediately of a fault condition. Because the
process variable (PV) status transmission precedes the PV value, we
are guaranteed that a bad PV is not used in a control algorithm. In
addition, bi-directional communication provides for remote transmitter
configuration directly from the human interface, enabling management
of the complete loop.”
Honeywell’s cost-effective ST 3000
S900 transmitters lead the industry in
reliability and stability:
•
•
Stability = ±0.01% per year
Reliability = 470 years MTBF
Maureen Atchison, DuPont
Site Electrical & Instrumentation Leader
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 3
Description of Diaphragm Seals
Figure 6 - Seals with Threaded Process
Connections can be used with differential, gauge and
absolute pressure transmitters and are available with
½”, ¾” and 1” NPT Female process connections.
Figure 6
Figure 7 - Sanitary Seals can be used with
differential, gauge and absolute pressure transmitters
and are available with 3” and 4” Tri-Clover-Tri-Clamp
process connections.
Figure 7
Figure 8
Figure 9
Figure 10
Figure 8 - Saddle Seals can be used with differential,
gauge and absolute pressure transmitters and are
available with 3” and 4” (6 bolt or 8 bolt designs)
process connections.
Figure 9 - Calibration Rings are available with Flush
Flange Seals and Pancake Seals. Flushing ports (1/4”
or ½”) are available with calibration rings.
Figure 10 - Stainless Steel Armor and PVC Coated
Stainless Steel Armor Capillaries are available with
Honeywell Remote Seal Solutions.
Figure 11 - 2” Stainless Steel Nipples are available
for Close-Coupled remote seal solutions.
Figure 11
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 4
Figure 12 - Welded Meter Body for All-Welded
Remote Seal Solution. The welded ST 3000 meter
body is an important part of an All-Welded Remote
Seal Solution, which is commonly used in Vacuum
applications.
Figure 12
Description
Features
•
•
Choice of linear or square
root output conformity is a
simple configuration selection.
The ST 3000 transmitter can replace any 4 to 20 mA output transmitter in
use today and operates over a standard two-wire system.
The measuring means is a piezoresistive sensor, which actually contains
three sensors in one. It contains a differential pressure sensor, a
temperature sensor, and a static pressure sensor.
Direct digital integration with
Experion PKS and other
control systems provides local
measurement accuracy to the
system level without adding
typical A/D and D/A converter
inaccuracies.
Microprocessor-based electronics provide higher span-turndown ratio,
improved temperature and pressure compensation, and improved
accuracy.
•
Unique piezoresistive sensor
automatically compensates
input for temperature and
static pressure.Added “smart”
features include configuring
lower and upper range
values, simulating accurate
analog output, and selecting
preprogrammed engineering
units for display.
The transmitter’s meter body and electronics housing resist shock,
vibration, corrosion, and moisture. The electronics housing contains a
compartment for the single-board electronics, which is isolated from an
integral junction box. The single-board electronics is replaceable and
interchangeable with any other ST 3000 Series 100 or Series 900 model
transmitter.
Like other Honeywell transmitters, the ST 3000 features two-way
communication and configuration capability between the operator and the
transmitter through several Honeywell field-rated portable configuration
devices, including the Smart Field Communicator (SFC) and the Multiple
Communication Configurator (MC ToolKit). While both are made for in-
field use, the MC Toolkit also can be ordered for use in intrinsically safe
environments.
•
Smart transmitter capabilities
with local or remote
interfacing means significant
manpower efficiency
improvements in
commissioning, start-up, and
ongoing maintenance
functions.
The SCT 3000 Smartline® Configuration Toolkit provides an easy way to
configure instruments using a personal computer. The toolkit enables
configuration of devices before shipping or installation. The SCT 3000 can
operate in the offline mode to configure an unlimited number of devices.
The database can then be loaded down-line during commissioning.
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 5
Specifications
Operating Conditions – All Models
Parameter
Reference
Condition
(at zero
Rated Condition
Operative Limits
Transportation
and Storage
static)
°C
°F
°C
°F
°C
°F
°C
°F
Ambient Temperature
25 ±1 77 ±2
25 ±1 77 ±2
-25 to 70
-13 to 158
-40 to 85
-40 to 185 -55 to 125 -67 to 257
-55 to 125 -67 to 257
See Figure 13
Process Interface
Temperature
Humidity
%RH
10 to 55
0 to 100
0 to 100
0 to 100
Maximum Allowable
Working Pressure (MAWP)
MAWP is minimum of Body Rating or Seal Rating (See Model Selection Guide for Seal
MAWP)
Body
MAWP
STR93D
STR94G
750 psig (52 bar)
500 psig (35 bar)
Vacuum Region, Minimum
Pressure - mmHg absolute
atmospheric
atmospheric
See Figure 13
inH O absolute
2
Supply Voltage, Current,
and Load Resistance
Voltage Range: 10.8 to 42.4 Vdc at terminals
Current Range: 3.0 to 21.8 mA
Load Resistance: 0 to 1440 ohms (as shown in Figure 14)
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 6
Maximum Pressure Limited
by Flange Rating of Seal
10000
9000
8000
7000
6000
193
psig
Silicone DC704
30 to 450°F
5000
4000
3000
2000
Silicone DC200
-40 to 350°F
1000
900
800
700
600
500
1Atm
0
CTFE
psig
5 to 300°F
400
300
200
-9
psig
100
90
80
70
60
50
40
30
Special High Vacuum
Construction required.
Consult STC.
Pressure20
(mmHgA)
-14
10
psig
450
-40
-100
175
350
5
25 30
100
500
0
200
300
400
Process Temperature (Degrees F)
Maximum Pressure Limited
by Flange Rating of Seal
10000
9000
193
psig
8000
7000
6000
Syltherm 800
-40 to 600°F
90
psig
5000
4000
NEOBEE M-20
30 to 400°F
3000
2000
1000
900
800
700
600
500
1Atm
0
psig
400
300
200
-9
psig
100
90
80
70
60
50
40
30
Pressure20
(mmHgA)
-14
10
psig
550
-40
-100
175
450
5
25 30
100
600
20335
0
200
400
500
Process Temperature (Degrees F)
Figure 13—ST 3000 Remote Seals operable limits for pressure versus temperature
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 7
1440
1200
Note: A minimum of 250 ohms
of loop resistance is necessary
to support communications.
Loop resistance equals barrier
resistance plus wire resistance
plus receiver resistance.
Loop
Resistance
(ohms)
800
650
450
250
= Operating Area
0
10.8
16.28 20.63 25 28.3 37.0
42.4
Operating Voltage (Vdc)
Figure 14—Supply voltage and loop resistance chart
Performance Under Rated Conditions * - Model STR93D (0 to 100 psi/7 bar)
Parameter
Description
Upper Range Limit
psi
bar
100 (Transmitter URL or maximum seal pressure rating, whichever is lower.)
7
Minimum Span
Turndown Ratio
psi
bar
0.9
0.063
110 to 1
Zero Elevation and Suppression No limit except minimum span within ±100% URL.
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability)
In Analog Mode: ±0.20% of calibrated span or upper range value (URV), whichever is
greater, terminal based.
For URV below reference point (50 inH O), accuracy equals:
2
• Accuracy includes residual error
after averaging successive
readings.
50 inH O
2
125 mbar
(span mbar)
⎛
⎝
⎞
⎠
±0.10 + 0.10
or ±0.10 + 0.10
in % of span
span inH O
2
In Digital Mode: ±0.175% of calibrated span or upper range value (URV), whichever
is greater, terminal based.
• For FOUNDATION Fieldbus use
Digital Mode specifications. For
HART use Analog Mode
specifications.
For URV below reference point (50 inH O), accuracy equals:
2
50 inH O
2
125 mbar
(span mbar)
⎛
⎝
⎞
⎠
±0.075 + 0.10
or ±0.075 + 0.10
in % of span
span inH O
2
Combined Zero and Span
Temperature Effect per 28°C
(50°F) **
In Analog Mode: ±1.5% of span.
For URV below reference point (200 inH O), effect equals:
2
200 in H2O
500 mbar
⎛
⎝
⎛
⎝
⎞
⎠
⎞
⎠
In % span
or ±0.30 + 1.2
±0.30 + 1.2
span in H2O
span mbar
In Digital Mode: ±1.475% of span.
For URV below reference point (200 inH O), effect equals:
2
200 in H2O
500 mbar
⎛
⎝
⎛
⎝
⎞
⎠
⎞
⎠
In % span
or ±0.275 + 1.2
±0.275 + 1.2
span in H2O
span mbar
*
Performance specifications are based on reference conditions of 25°C (77°F), zero (0) static pressure, 10 to 55% RH, and
316L Stainless Steel barrier diaphragm.
** Specification applies to transmitters with 2 seals only. Apply 1.5 times factor to temperature effect for capillary lengths greater than 10 feet
or for 2-inch sanitary seals.
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 8
Performance Under Rated Conditions * - Models STR94G (0 to 500 psi/35 bar)
Parameter
Description
Upper Range Limit
psi
bar
500
35
Minimum Span
Turndown Ratio
psi
bar
20
1.4
25 to 1
Zero Elevation and Suppression No limit except minimum span from absolute 0 (zero) to +100% URL.
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability)
In Analog Mode: ±0.10% of calibrated span or upper range value (URV), whichever is
greater, terminal based.
In Digital Mode: ±0.075% of calibrated span or upper range value (URV), whichever
• Accuracy includes residual error is greater, terminal based.
after averaging successive
readings.
• For FOUNDATION Fieldbus use
Digital Mode specifications. For
HART use Analog Mode
specifications.
*
Performance specifications are based on reference conditions of 25°C (77°F), zero (0) static pressure, 10 to 55% RH, and
316L Stainless Steel barrier diaphragm.
Transmitter Minimum Span and Maximum Capillary Length
Minimum recommended span for STR93D DP Transmitter with two Remote Seals
Diaphragm
Capillary
20'
Capillary Length
Size
2.0
2.4
2.9
3.5
4.1
5'
10'
15'
25'
-
350 iwc
150 iwc
32 iwc
25 iwc
30'
-
400 iwc
175 iwc
36 iwc
27 iwc
35'
-
450 iwc
200 iwc
40 iwc
30 iwc
maximum
15 psig
150 iwc
50 iwc
25 iwc
25 iwc
20 psig
200 iwc
75 iwc
25 iwc
25 iwc
25 psig
250 iwc
100 iwc
25 iwc
25 iwc
-
15'
35'
35'
35'
35'
300 iwc
125 iwc
28 iwc
25 iwc
Minimum recommended span for STR94G or STR93D DP Transmitter with one Remote Seal
Diaphragm Direct
Capillary
Capillary Length
Size
2.0
2.4
2.9
3.5
4.1
Mount
25 psi
10 psi
8 psi
2 psi
0.9 psi
5'
10'
15'
20'
-
30 psi
12 psi
5 psi
3 psi
30'
-
40 psi
14 psi
7 psi
4 psi
35'
-
50 psi
15 psi
8 psi
5 psi
maximum
30 psi
15 psi
9 psi
2 psi
0.9 psi
40 psi
20 psi
10 psi
3 psi
50 psi
25 psi
11 psi
4 psi
15'
35'
35'
35'
35'
1 psi
2 psi
Minimum span is the higher of the value from the table above or the value defined under Performance Conditions for the range transmitter
Figure 15— Maximum capillary length and diaphragm size chart.
Performance Under Rated Conditions - General for all Models
Parameter
Description
Output (two-wire)
Analog 4 to 20 mA or DE digital communications mode. Options available for
FOUNDATION Fieldbus and HART protocols.
Supply Voltage Effect
Damping Time Constant
CE Conformity (Europe)
0.005% of span per volt.
Adjustable from 0 to 32 seconds digital damping.
89/336/EEC, Electromagnetic Compatibility (EMC) Directive.
NAMUR NE 43 Compliance
Option
Transmitter failure information is generated when the measuring information is invalid or
no longer present. Failure information is transmitted as a current signal but outside the
normal 4-20 mA measurement signal level. Transmitter failure values are:
≤ 3.6 mA and ≥ 21.0 mA. The normal signal range is ≥ 3.8 mA and ≤ 20.5 mA.
SIL certified to IEC 61508 for non-redundant use in SIL 2 related Safety Systems
(single use) and for redundant (multiple) use in SIL 3 Safety Systems through
TÜV Nord Sys Tec GmbH & Co. KG under the following standards: IEC61508-1: 1998;
IEC 61508-2: 2000; IEC61508-3: 1998.
SIL 2/3 Compliance
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 9
Physical and Approval Bodies
Parameter
Description
Process Interface
See Model Selection Guide for Material Options for desired Seal Type.
316L Stainless Steel, Monel, Hastelloy C, Tantalum
Klinger C-4401 (non-asbestos)
Seal Barrier Diaphragm
Seal Gasket Materials
Grafoil
Teflon
Gylon 3510
Mounting Bracket
Carbon Steel (zinc-plated) or Stainless Steel angle bracket or Carbon Steel flat
bracket available.
Fill Fluid (Meter Body)
Silicone (DC 200)
S.G. @ 25°C (77°F) = 0.94
S.G. @ 25°C (77°F) = 1.89
CTFE (Chlorotrifluoroethylene)
Fill Fluid (Secondary)*
Silicone (DC 200)
S.G. @ 25°C (77°F) = 0.94
S.G. @ 25°C (77°F) = 1.89
CTFE (Chlorotrifluoroethylene)
Silicone (DC 704)
Syltherm 800
S.G. @ 25°C (77°F) = 1.07
S.G. @ 25°C (77°F) = 0.90
NEOBEE M-20
S.G. @ 25°C (77°F) = 0.93
Electronics Housing
Epoxy-Polyester hybrid paint. Low-copper aluminum alloy. Meets NEMA 4X
(watertight) and NEMA 7 (explosion proof)
Capillary Tubing**
Armored Stainless Steel or PVC Coated Armored Stainless Steel. Length: 5, 10,
15, 20, 25 and 35 feet (1.5, 3, 4.6, 6.1, 7.5 and 10.7m). A 2” (51 millimeter) S.S.
close-coupled nipple is also available. See Model Selection Guide.
Wiring
Accepts up to 16 AWG (1.5 mm diameter)
See Figure 16.
Mounting
Dimensions
See Figures 19 and 20 for transmitter dimensions. See Model Selection Guide for
Seal dimensions
Net Weight
Transmitter: 4.1 Kg (9 lbs). Total weight is dependent on seal type and capillary
length.
Approval Bodies
Explosion Proof: Approved as Explosion Proof for Class I, Division 1, Groups A,
B, C, D locations,
Dust Ignition Proof: Approved as Dust Ignition Proof for Class II, III, Division 1,
Groups E, F, G locations,
Factory Mutual
Intrincically Safe: Approved as Intrinsically Safe for for Class I, II, III, Division 1,
Groups A, B, C, D, E, F, G locations.
Nonincendive: Approved as Nonincendive for Class I, Division 2, Groups A, B, C,
D locations.
Explosion Proof: Approved as Explosion Proof for Class I, Division 1, Groups B,
C, D locations,
Dust Ignition Proof: Approved as Dust Ignition Proof for Class II, III, Division 1,
Groups E, F, G locations,
CSA
Intrincically Safe: Approved as Intrinsically Safe for Class I, II, III, Division 1,
Groups A, B, C, D, E, F, G locations.
Canadian Registration
Number (CRN)
All ST 3000 model designs, except SATG19L, STG99L, STG170 and STG180
have been registered in all provinces and territories in Canada and are marked
CRN:0F8914.5c.
Intrinsically Safe, Zone 0/1: EEx ia IIC T4, T5, T6
Flameproof/Zone 1:
Non-Sparking, Zone 2:
Multiple Markings:
EEx d IIC T5, T6 (enclosure IP 66/67)
EEx nA, IIC T6 (enclosure IP 66/67)
Ex II 1 G: EEx ia IIC T4, T5, T6, Ex II 2 G: EExd IIC T5, T6
Ex II 3 G: EEx nA, IIC T6 (Honeywell) (enclosure IP 66/67)
ATEX
Intrinsically Safe: EX ia IIC T4
Non-Sparking: Ex n IIC T6 (T4 with SM option)
SA (Australian)
INMETRO (Brazil)
Flame-Proof, Zone 1: EX d IIC T5
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 10
Parameter
Description
Pressure Equipment Directive
(97/23/EC)
The ST 3000 pressure transmitters listed in this Specification have no pressurized
internal volume or have a pressurized internal volume rated less than 1,000 bar
(14,500 psig) and/or have a maximum volume of less than 0.1 liter. Therefore,
these transmitters are either; not subject to the essential requirements of the
directive 97/23/EC (PED, Annex 1) and shall not have the CE mark, or the
manufacturer has the free choice of a module when the CE mark is required for
pressures > 200 bar (2,900 psig).
*
See Figure 13 for Fill Fluid temperature limits.
** 2-inch Sanitary Seals are limited to 15 ft. (4.6 m) capillary length.
NOTE: Pressure transmitters that are part of safety equipment for the protection of piping (systems) or vessel(s) from
exceeding allowable pressure limits, (equipment with safety functions in accordance with Pressure Equipment Directive
97/23/EC article 1, 2.1.3), require separate examination.
LP Side
Maximum level
H2
Fixed
ref. leg
Variable
Head
H1
Minimum level
.
HP Side
NOTE: Lower flange seal should not be mounted over 22 feet below the
transmitter for silicone fill fluid (11 feet for CTFE fill fluid) with tank at one
atmosphere. The combination of tank vacuum and high pressure capillary
head effect should not exceed 9 psi vacuum (300 mmHg absolute).
Consult Honeywell for installation of STR93D
Figure 16—Typical mounting arrangement for ST 3000 Transmitter with Remote Diaphragm Seals
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 11
Application Data
Liquid Level: Closed Tank
Determine the minimum and
maximum pressure differentials to
be measured (Figure 17).
Max
LP
Level
P
Min
= (SG x a) - (SG x d)
p
f
b
= LRV when HP at bottom of
tank
Min
= –URV when LP at bottom of
tank
HP
a
Level
P
Max
= (SG x b) - (SG x d)
p
f
¥ Transmitter above datum
= URV when HP at bottom of
tank
= –LRV when LP at bottom of
tank
Max
LP
Where:
Level
minimum level = 4mA
maximum level = 20 mA
b
Min
a = distance between bottom tap
and minimum level
HP
a
Level
b = distance between bottom tap
and maximum level
¥ Transmitter at datum
d = distance between taps
SG = Specific Gravity of capillary
f
Max
LP
fill fluid (See Page 9 for
values.)
Level
SG = Specific Gravity of process
p
fluid
b
Min
HP
a
Level
¥ Transmitter below datum
24253
Figure 17—Closed tank liquid level measurement distances
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 12
Density or Interface
Calculate the minimum and
maximum pressure differentials to
be measured (Figure 18).
P
min
= (SG
– SG ) x (d);
min
f
minimum density, 4mA output
LP
P
max
= (SG – SG ) x (d);
max
f
maximum density, 20mA output
Where:
d = distance between the taps
HP
SG
= maximum Specific
Gravity
max
min
24257
SG
= minimum Specific Gravity
SG = Specific Gravity of capillary
f
Figure 18—Density, direct acting transmitter configuration
fill fluid (See Page 9 for
values.)
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 13
Reference Dimensions:millimeters
Inches
With
Smart
meter
82.9
3.26
94.9
3.74
Removal
Clearance
for All Caps
3.6
0.14
Plug
53.1
2.09
65.1
2.56
135
5.32
with meter
45.7
1.8
Without
Without
meter
meter
55.3
2.18
23.5
.925
Optional
Meters
Optional
external
ground
Rotational
Lock
LP seal
omitted for
clarity
67
2.64
93.6
3.69
STR93D DP/I Remote Seal with Horizontal Pipe Mount
With
82.9
3.26
94.9
3.74
Removal
Clearance
Smart
meter
3.6
0.14
Plug
for All Caps
53.1
2.09
65.1
2.56
135
5.32
with meter
45.7
1.8
Without
Without
meter
meter
55.3
2.18
23.5
.925
Seal
omitted for
clarity
Optional
Meters
Optional
external
ground
Rotational
Lock
24272
STR94G LGP/I Remote Seal with Horizontal Pipe Mount
Figure 19—Approximate horizontal mounting dimensions for Remote Seal Transmitter.
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 14
Reference Dimensions:millimeters
Inches
With
82.9
94.9
3.74
Removal
Smart
3.26
Clearance
for All Caps
with meter
3.6
0.14
meter
Plug
53.1
2.09
65.1
135
5.32
2.56
45.7
1.8
Without
Without
meter
meter
55.3
2.18
Seal
omitted for
clarity
23.5
.925
LP seal
omitted for
clarity
Rotational
Lock
Optional
Meters
Optional
external
ground
67
2.64
93.6
3.69
STR93D DP/I Remote Seal with Vertical Pipe Mount
With
Smart meter
82.9
3.26
94.9
3.74
Removal
3.6
0.14
135
5.32
Plug
Clearance
for All Caps
with meter
65.1
2.56
53.1
2.09
Without
meter
45.7
1.8
Without
55.3
2.18
meter
Rotational
Lock
23.5
.925
Optional
Meters
Optional
external
ground
Seal
omitted for
clarity
STR94G LGP/I Remote Seal with Vertical Pipe Mount
24273
Figure 20—Approximate vertical mounting dimensions for Remote Seal Transmitter
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 15
Options
We are in compliance with the
Ordering Information
Mounting Bracket
Contact your nearest Honeywell sales
office, or
The angle-mounting bracket is
available in either zinc-plated
carbon steel or stainless steel and
is suitable for horizontal or vertical
mounting on a two-inch (50
millimeter) pipe, as well as wall
mounting. An optional flat
mounting bracket is also available
in carbon steel for two inch (50
millimeter) pipe mounting.
following SIL standards:
IEC 61508-1: 1998;
IEC 61508-2: 2000;
IEC 61508-3: 1998
In the U.S.:
Honeywell
NAMUR NE43 Compliance
(Option NE)
This option provides software the
Industrial Automation & Control
16404 North Black Canyon Hwy.
Phoenix, AZ 85053
1-800-288-7491
meets the NAMUR NE43
requirements for failsafe software.
Transmitter failure information is
generated when the measuring
information is no longer valid.
Transmitter failure values are:
≤ 3.6 mA and ≥ 21.0 mA. The
normal ST 3000 ranges are ≤ 3.8
mA and ≥ 20.5 mA.
In Canada:
The Honeywell Centre
155 Gordon Baker Rd.
North York, Ontario M2H 3N7
1-800-461-0013
Indicating Meter
(Options ME and SM)
Two integral meter options are
available. An analog meter (option
ME) is available with a 0 to 100%
linear scale. The Smart Meter
(option SM) provides an LCD
display for both analog and digital
output and can be configured to
display pressure in pre-selected
engineering units.
In Latin America:
Honeywell Inc.
480 Sawgrass Corporate Parkway,
Suite 200
Indicator Configuration
(Option CI)
Provides custom configuration of
Smart Meters.
Sunrise, FL 33325
(954) 845-2600
In Europe and Africa:
Honeywell S. A.
Tagging (Option TG)
Lightning Protection
(Option LP)
Up to 30 characters can be added
on the stainless steel nameplate
mounted on the transmitter’s
electronics housing at no extra
cost. Note that a separate
nameplate on the meter body
contains the serial number and
body-related data. A stainless
steel wired on tag with additional
data of up to 4 lines of 28
Avenue du Bourget 1
1140 Brussels, Belgium
A terminal block with circuitry that
protects the transmitter from
transient surges induced by
nearby lightning strikes is
available.
In Eastern Europe:
Honeywell Praha,
s.r.o. Budejovicka 1
140 21 Prague 4,
Czech Republic
HART® Protocol Compatibility
(Options HC and H6)
Optional electronics modules for
the ST 3000 provides HART
Protocol compatibility in either
HART 5.x or 6.x formats.
In the Middle East:
Honeywell Middle East Ltd.
Khalifa Street,
characters is also available. The
number of characters for tagging
includes spaces.
Sheikh Faisal Building
Abu Dhabi, U. A. E.
Transmitters with a HART Option
are compatible with any HART
enabled system that provides 5.x
or 6.x format support.
Transmitter Configuration
(Option TC)
In Asia:
Honeywell Asia Pacific Inc.
Honeywell Building,
17 Changi Business Park Central 1
Singapore 486073
The factory can configure the
transmitter linear/square root
extraction, damping time, LRV,
URV and mode (analog/digital)
and enter an ID tag of up to eight
characters and scratchpad
information as specified.
FOUNDATION Fieldbus
(Option FF)
Republic of Singapore
Equips transmitter with FF
protocol for use in 31.25 kbit/s FF
networks. See document 34-ST-
03-72 for additional information on
ST 3000 Fieldbus transmitters.
In the Pacific:
Honeywell Pty Ltd.
5 Thomas Holt Drive
North Ryde NSW Australia 2113
(61 2) 9353 7000
Custom Calibration and ID in
Memory (Option CC)
The factory can calibrate any
range within the scope of the
transmitter’s range and enter an
ID tag of up to eight characters in
the transmitter’s memory.
SIL2/SIL3 Certification
(Option SL)
In Japan:
Honeywell K.K.
This ST 3000 product is available
for use with safety systems. With
the SL option, we are fully certified
to SIL 2 capability for single
transmitters and SIL 3 capability for
multiple transmitter use through
TÜV Nord Sys Tec GmbH & Co.
KG. (continued)
14-6 Shibaura 1-chrome
Minato-ku, Tokyo, Japan 105-0023
Or, visit Honeywell on the World Wide
Web at: http://www.honeywell.com
Specifications are subject to change without
notice. (Note that specifications may differ
slightly for transmitters manufactured before
October 30, 1995.)
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 16
Model Selection Guide (34-ST-16-34)
Instructions
•
•
•
•
•
Select the desired Key Number. The arrow to the right marks the selection available.
Make one selection from each table, I and II, using the column below the proper arrow.
Select as many Table III options as desired (if no options are desired, specify 9X).
A (•) denotes unrestricted availability. A letter denotes restricted availability.
Restrictions follow Table IV.
I
II
III (Optional)
IV
Key Number
_ _ _ _ _ _
-
_ _ _
- _ _ _ _ _ _ _ _ _ _ _ _
-
_ _, _ _, _ _
+
XXXX
KEY NUMBER
Selection
Avail.
Description
0-25" to 0-2700" H2O/0-62.2 to 0-7000 mbar
STR93D
Body Rating*: 750 psi (51.7 bar) Compound Characterized
0-20 to 0-500 psig/0-1.4 to 0-35 bar
STR94G
Body Rating*: 500 psi (35 bar)
* Remote seal system pressure rating is body rating or seal rating, whichever is less.
TABLE I - METER BODY
Description
Selection
1 _ _
2 _ _
3 _ _
5 _ _
Avail.
1 Remote Seal (High Side)
•
•
•
2 Remote Seals
1 Remote Seal (Low Side)
Number of Seals
•
8
•
Value Added Model (VAM unit)
Silicone (DC 200)
Fill Fluid (Meter Body)
CTFE
8
•
_ 1 _
_ 2 _
q
q
Non-Wetted Material
Construction
316 SS
_ _ A
_ _ D
_ _ A
_ _ D
_ _ C
•
y
In-Line Gauge
316 SS for Close-Couple
316 SS Heads
•
y
7
Dual Head DP
316 SS Heads for Close-Couple connection
316 SS with all-welded meter body
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 17
TABLE II - SEALS
Format for Seal Selection:
Specify 12 characters
Availability
_ _ _ _ _ _ _ _ _ _ _ _
Common Required Seal
STR9xx
Note:
The first 3 characters are common to all seals.
When selecting required seal, you must specify
3D 4G
Selection
only the 9 selections within the required seal.
No Fill Fluid
Silicone (DC 200)
CTFE
Silicone (DC 704)
Neobee (M20) **
Syltherm 800 ***
0 _ _ _ _ _ _ _ _ _ _ _
1 _ _ _ _ _ _ _ _ _ _ _
2 _ _ _ _ _ _ _ _ _ _ _
3 _ _ _ _ _ _ _ _ _ _ _
4 _ _ _ _ _ _ _ _ _ _ _
5 _ _ _ _ _ _ _ _ _ _ _
3
•
•
p
•
3
•
•
p
•
Secondary Fill
p
p
No Capillary, No Nipple
_ 0 _ _ _ _ _ _ _ _ _ _
_ A _ _ _ _ _ _ _ _ _ _
_ B _ _ _ _ _ _ _ _ _ _
_ C _ _ _ _ _ _ _ _ _ _
_ D _ _ _ _ _ _ _ _ _ _
_ E _ _ _ _ _ _ _ _ _ _
_ F _ _ _ _ _ _ _ _ _ _
_ G _ _ _ _ _ _ _ _ _ _
_ H _ _ _ _ _ _ _ _ _ _
_ J _ _ _ _ _ _ _ _ _ _
_ K _ _ _ _ _ _ _ _ _ _
_ L _ _ _ _ _ _ _ _ _ _
_ M _ _ _ _ _ _ _ _ _ _
3
3
5 feet
10 feet
15 feet
20 feet
25 feet
35 feet
5 feet
1.5 m
3.0 m
4.5 m
6.1 m
7.5 m
10.7 m
1.5 m
3.0 m
4.5 m
6.1 m
7.5 m
10.7 m
•
•
•
•
•
•
•
•
•
•
•
•
z
•
•
•
•
•
•
•
•
•
•
•
•
z
SS Armor
Connection of
Remote Seal to
Meter Body
Capillary
Length
10 feet
15 feet
20 feet
25 feet
35 feet
PVC Coated SS Armor
2 inch long SS nipple close-coupled
_ 2 _ _ _ _ _ _ _ _ _ _
_ _ 0 _ _ _ _ _ _ _ _ _
_ _ _ 0 0 0 0 0 0 0 0 0
No Selection
•
3
•
3
No Seal Attached to Core Transmitter
Diaphragm
Diameter
Flange Size
Flange Pressure Rating *
Selection
ANSI Class 150
ANSI Class 300
DIN DN80-PN40
_ _ _ AFA _ _ _ _ _ _
_ _ _ AFC _ _ _ _ _ _
_ _ _ AFM _ _ _ _ _ _
Selection
•
•
•
•
•
•
3.5"
3"
Diaphragm
Upper Insert
316 SS
316L SS
Hastelloy C
Hastelloy C
Monel
_ _ _ _ _ _ AA _ _ _ _
_ _ _ _ _ _ AB _ _ _ _
_ _ _ _ _ _ AC _ _ _ _
_ _ _ _ _ _ AE _ _ _ _
_ _ _ _ _ _ AF _ _ _ _
_ _ _ _ _ _ _ _ 1 _ _ _
_ _ _ _ _ _ _ _ 2 _ _ _
_ _ _ _ _ _ _ _ _ 1 _ _
_ _ _ _ _ _ _ _ _ 2 _ _
_ _ _ _ _ _ _ _ _ _ A _
_ _ _ _ _ _ _ _ _ _ B _
_ _ _ _ _ _ _ _ _ _ C _
_ _ _ _ _ _ _ _ _ _ D _
Table II continued next page
•
•
•
•
1
•
•
•
•
1
316 SS
Wetted Material
Flange Material
Hastelloy C
Monel
Flush Flanged
Seal
Tantaluma
Tantalum
CS (Nickel Plated)
•
•
•
•
316 SS
Center of Seal
Side of Seal
None
Seal-Capillary
Connection
•
9
•
9
•
•
316 SS
5
5
5
5
5
5
Calibration Rings
Hastelloy C
Monel
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 18
Availability
3D 4G
STR9xx
TABLE II - SEALS (continued)
Description
Selection
Flushing
None
_ _ _ _ _ _ _ _ _ _ _ 0
_ _ _ _ _ _ _ _ _ _ _ H
_ _ _ _ _ _ _ _ _ _ _ J
_ _ _ _ _ _ _ _ _ _ _ M
_ _ _ _ _ _ _ _ _ _ _ N
_ _ _ _ _ _ _ _ _ _ _ P
_ _ _ _ _ _ _ _ _ _ _ Q
_ _ _ _ _ _ _ _ _ _ _ R
_ _ _ _ _ _ _ _ _ _ _ S
Table II continued below
•
6
6
6
6
6
6
6
6
•
6
6
6
6
6
6
6
6
Connections
One 1/4" with plastic plug
One 1/4" with metal plug
Two 1/4" with plastic plugs
Two 1/4" with metal plugs
One 1/2" with plastic plug
One 1/2" with metal plug
Two 1/2" with plastic plugs
Two 1/2" with metal plugs
and Plugs**
Metal plug material
will be the same as
Lower material, if
metal plug is chosen -
(SS Plug for CS Lower
and Tantalum Clad)
Flush Flanged
Seal
*
**
Standard facing 125-250 AARH RF (raised face) serrated surface finish.
Limited vacuum availability.
***
****
a
Minimum static pressure requirement. No vacuum allowed. See Specification Figure 13.
Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
Tantalum Upper insert has Tantalum wetted parts and 316SS or CS non-wetted parts
STR9xx
3D 4G
TABLE II - SEALS (continued)
Const. - See
Spec. Figure 34-
Diaphragm
Diameter
Flange Pressure
Rating *
Flange Size
Selection
ST-03-57
22
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
150
300
150
300
150
300
150
300
150
150
300
150
300
150
300
150
150
300
150
300
150
300
150
300
_ _ _ BCA _ _ _ _ _ _
_ _ _ BCC _ _ _ _ _ _
_ _ _ BGA _ _ _ _ _ _
_ _ _ BGC _ _ _ _ _ _
_ _ _ BDA _ _ _ _ _ _
_ _ _ BDC _ _ _ _ _ _
_ _ _ BFA _ _ _ _ _ _
_ _ _ BFC _ _ _ _ _ _
_ _ _ CAA _ _ _ _ _ _
_ _ _ CCA _ _ _ _ _ _
_ _ _ CCC _ _ _ _ _ _
_ _ _ CGA _ _ _ _ _ _
_ _ _ CGC _ _ _ _ _ _
_ _ _ CDA _ _ _ _ _ _
_ _ _ CDC _ _ _ _ _ _
_ _ _ DAA _ _ _ _ _ _
_ _ _ DCA _ _ _ _ _ _
_ _ _ DCC _ _ _ _ _ _
_ _ _ DGA _ _ _ _ _ _
_ _ _ DGC _ _ _ _ _ _
_ _ _ DDA _ _ _ _ _ _
_ _ _ DDC _ _ _ _ _ _
_ _ _ DFA _ _ _ _ _ _
_ _ _ DFC _ _ _ _ _ _
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1"
1-1/2"
2"
22
22
22
22
22
22
22
23
23
23
22
22
2.4"
3"
1/2"
1"
2.9"
Flush Flanged
Seal with Lower
1-1/2"
2"
22
22
1/2"
1"
23
23
23
23
23
23
22
22
1-1/2"
2"
4.1"
3"
22
Table II continued next page
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 19
Availability
3D 4G
STR9xx
TABLE II - SEALS (continued)
Diaphragm
316L SS
Hastelloy C
Hastelloy C
Monel
Lower
316 SS
Selection
_ _ _ _ _ _ BA _ _ _ _
_ _ _ _ _ _ BB _ _ _ _
_ _ _ _ _ _ BC _ _ _ _
_ _ _ _ _ _ BE _ _ _ _
_ _ _ _ _ _ BF _ _ _ _
_ _ _ _ _ _ BG _ _ _ _
_ _ _ _ _ _ BH _ _ _ _
Selection
•
•
•
•
316 SS
Hastelloy C
Monel
•
•
•
•
Wetted Material
Tantalum
Tantalum
Tantalum
Upper
316 SS
1
1
Hastelloy C
Tantalum Clad
Upper Insert
316 SS
1
1
10 10
Non-Wetted Material
(upper, upper insert)
316 SS
_ _ _ _ _ _ _ _ 4 _ _ _
_ _ _ _ _ _ _ _ 5 _ _ _
_ _ _ _ _ _ _ _ _ 0 _ _
_ _ _ _ _ _ _ _ _ _ 0 _
_ _ _ _ _ _ _ _ _ _ H _
_ _ _ _ _ _ _ _ _ _ J _
_ _ _ _ _ _ _ _ _ _ M _
_ _ _ _ _ _ _ _ _ _ N _
_ _ _ _ _ _ _ _ _ _ P _
_ _ _ _ _ _ _ _ _ _ Q _
_ _ _ _ _ _ _ _ _ _ R _
_ _ _ _ _ _ _ _ _ _ S _
_ _ _ _ _ _ _ _ _ _ _ K
•
•
•
•
•
•
Carbon Steel
316 SS
Bolts***
Flushing
No Selection
Flush Flanged
Seal with Lower
(continued)
None
•
•
•
•
•
•
•
•
•
c
•
•
•
•
•
•
•
•
•
c
Connections
One 1/4" with plastic plug
One 1/4" with metal plug
Two 1/4" with plastic plugs
Two 1/4" with metal plugs
One 1/2" with plastic plug
One 1/2" with metal plug
Two 1/2" with plastic plugs
Two 1/2" with metal plugs
Klinger C-4401
and Plugs**
Metal plug material
will be the same as
Lower material, if
metal plug is chosen -
(SS Plug for CS Lower
and Tantalum Clad)
(non-asbestos)
Gasket
Grafoil
_ _ _ _ _ _ _ _ _ _ _ G
_ _ _ _ _ _ _ _ _ _ _ T
_ _ _ _ _ _ _ _ _ _ _ L
•
c
d
•
c
d
Teflon
Gylon 3510
Diaphragm
Flange Size
Diameter
Flange Pressure Rating *
Selection
ANSI Class 150
ANSI Class 300
DIN DN80-PN40
ANSI Class 150
ANSI Class 300
DIN DN100-PN40
3"
(2.8" OD
_ _ _ EFA _ _ _ _ _ _
_ _ _ EFC _ _ _ _ _ _
_ _ _ EFM _ _ _ _ _ _
_ _ _ FGA _ _ _ _ _ _
_ _ _ FGC _ _ _ _ _ _
_ _ _ FGP _ _ _ _ _ _
Selection
•
•
•
•
•
•
•
•
•
•
•
•
2.8"
3.5"
extension)
4"
(3.70" OD
extension)
Diaphragm
316L SS
Ext. Tube
316 SS
Flange Seal with
Extended
Diaphragm
_ _ _ _ _ _ EA _ _ _ _
_ _ _ _ _ _ EB _ _ _ _
_ _ _ _ _ _ EC _ _ _ _
_ _ _ _ _ _ _ _ 7 _ _ _
_ _ _ _ _ _ _ _ 8 _ _ _
_ _ _ _ _ _ _ _ _ 0 _ _
_ _ _ _ _ _ _ _ _ _ 2 _
_ _ _ _ _ _ _ _ _ _ 4 _
_ _ _ _ _ _ _ _ _ _ 6 _
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Wetted Material
Hastelloy C
Hastelloy C
316 SS
Hastelloy C
CS (Nickel Plated)
Flange Material
Bolts
316 SS
No Selection
2"
4"
6"
Extension Length
No Selection
No Selection
_ _ _ _ _ _ _ _ _ _ _ 0
•
•
Table II continued next page
Standard facing 125-250 AARH RF (raised face) serrated finish.
Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
*
**
Bolt material will be same as Upper Material. However, if Table III bolt/nut option chosen, seal bolt material will be the same.
***
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 20
STR9xx
3D 4G
TABLE II - SEALS (continued)
Diaphragm
Diameter
Flange Pressure Rating Dependent
on Customer Flange
Flange Size
Selection
ANSI Class 150/300/600
3.5"
3"
_ _ _ GFA _ _ _ _ _ _
Selection
•
•
Diaphragm
316L SS
Body
316 SS
_ _ _ _ _ _ GA _ _ _ _
_ _ _ _ _ _ GB _ _ _ _
_ _ _ _ _ _ GC _ _ _ _
_ _ _ _ _ _ GE _ _ _ _
_ _ _ _ _ _ GG _ _ _ _
_ _ _ _ _ _ _ _ 0 _ _ _
_ _ _ _ _ _ _ _ _ 0 _ _
_ _ _ _ _ _ _ _ _ _ A _
_ _ _ _ _ _ _ _ _ _ B _
_ _ _ _ _ _ _ _ _ _ C _
_ _ _ _ _ _ _ _ _ _ D _
_ _ _ _ _ _ _ _ _ _ _ 0
_ _ _ _ _ _ _ _ _ _ _ H
_ _ _ _ _ _ _ _ _ _ _ J
_ _ _ _ _ _ _ _ _ _ _ M
_ _ _ _ _ _ _ _ _ _ _ N
_ _ _ _ _ _ _ _ _ _ _ P
_ _ _ _ _ _ _ _ _ _ _ Q
_ _ _ _ _ _ _ _ _ _ _ R
_ _ _ _ _ _ _ _ _ _ _ S
Table II continued below
•
•
•
•
1
•
•
•
•
•
•
1
•
•
Hastelloy C
Hastelloy C
Monel
316 SS
Wetted Material
Hastelloy C
Monel
Tantaluma
Tantalum
Non-Wetted Materials
No Selection
No Selection
No Selection
None
•
5
5
5
•
5
5
5
316 SS
Pancake Seal
Calibration Rings
Hastelloy C
Monel
Flushing
None
•
•
6
6
6
6
6
6
6
6
Connections
6
6
6
6
6
6
6
6
One 1/4" with plastic plug
One 1/4" with metal plug
Two 1/4" with plastic plugs
Two 1/4" with metal plugs
One 1/2" with plastic plug
One 1/2" with metal plug
Two 1/2" with plastic plugs
Two 1/2" with metal plugs
and Plugs**
Metal plug material
will be the same as
Lower material, if
metal plug is chosen -
(SS Plug for CS Lower
and Tantalum Clad)
a
Tantalum Body has Tantalum wetted parts and 316SS non-wetted parts
Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
***
STR9xx
3D 4G
TABLE II - SEALS (continued)
Diaphragm
Flange Size
Flange Pressure Rating
Selection
Diameter
Taylor
Wedge 5"
O.D.
v
3.5"
750 psi
_ _ _ HM0 _ _ _ _ _ _
Diaphragm
Body
316 SS
316 SS
Selection
316L SS
Hastelloy C
Hastelloy C
_ _ _ _ _ _ HA _ _ _ _
_ _ _ _ _ _ HB _ _ _ _
_ _ _ _ _ _ HC _ _ _ _
•
•
•
Wetted Material
Chemical Tee
"Taylor" Wedge
Hastelloy C
Non-Wetted Material
Bolts
No Selection
_ _ _ _ _ _ _ _ 0 _ _ _
_ _ _ _ _ _ _ _ _ 0 _ _
_ _ _ _ _ _ _ _ _ _ 0 _
_ _ _ _ _ _ _ _ _ _ _ 0
•
•
•
•
No Selection
No Selection
No Selection
Styles
No Selection
Table II continued next page
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 21
Availability
3D 4G
STR9xx
TABLE II - SEALS (continued)
Seal Pressure
Rating *
Threaded Process
Connection Size
Diaphragm
Diameter
(NPT
Selection
304 SS
C.S. Bolts
Female)
Bolts
1/2" NPT
3/4" NPT
1" NPT
_ _ _ JJG _ _ _ _ _ _
_ _ _ JKG _ _ _ _ _ _
_ _ _ JLG _ _ _ _ _ _
_ _ _ KJG _ _ _ _ _ _
_ _ _ KKG _ _ _ _ _ _
_ _ _ KLG _ _ _ _ _ _
_ _ _ LJG _ _ _ _ _ _
_ _ _ LKG _ _ _ _ _ _
_ _ _ LLG _ _ _ _ _ _
Selection
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2.4"
2.9"
4.1"
2500 psi 1250 psi
1/2" NPT
3/4" NPT
1" NPT
2500 psi 1250 psi
1500 psi 750 psi
1/2" NPT
3/4" NPT
1" NPT
Diaphragm
Lower
Carbon Steel
316 SS
316L SS
316L SS
_ _ _ _ _ _ JA _ _ _ _
_ _ _ _ _ _ JB _ _ _ _
_ _ _ _ _ _ JC _ _ _ _
_ _ _ _ _ _ JD _ _ _ _
_ _ _ _ _ _ JE _ _ _ _
_ _ _ _ _ _ JF _ _ _ _
_ _ _ _ _ _ JG _ _ _ _
_ _ _ _ _ _ _ _ A _ _ _
_ _ _ _ _ _ _ _ C _ _ _
_ _ _ _ _ _ _ _ _ C _ _
_ _ _ _ _ _ _ _ _ D _ _
_ _ _ _ _ _ _ _ _ _ 0 _
_ _ _ _ _ _ _ _ _ _ H _
_ _ _ _ _ _ _ _ _ _ J _
_ _ _ _ _ _ _ _ _ _ M _
_ _ _ _ _ _ _ _ _ _ N _
_ _ _ _ _ _ _ _ _ _ P _
_ _ _ _ _ _ _ _ _ _ Q _
_ _ _ _ _ _ _ _ _ _ R _
_ _ _ _ _ _ _ _ _ _ S _
_ _ _ _ _ _ _ _ _ _ _ K
•
•
•
•
•
1
1
•
•
•
•
•
1
1
Hastelloy C
Hastelloy C
Monel
316 SS
Wetted Material
Hastelloy C
Monel
Tantalum
Tantalum
316 SS
Hastelloy C
Seal with
Threaded
Process
CS (Nickel Plated)
Non-Wetted Material
(upper)
•
w
1
•
w
1
Stainless Steel
Carbon Steel
304 SS
Connection
Bolts***
•
•
•
•
•
•
•
•
•
•
•
•
Flushing
Connections
and Plugs**
None
One 1/4" with plastic plug
One 1/4" with metal plug
Two 1/4" with plastic plugs
Two 1/4" with metal plugs
One 1/2" with plastic plug
One 1/2" with metal plug
Two 1/2" with plastic plugs
Two 1/2" with metal plugs
Klinger C-4401
Metal plug material
will be the same as
Lower material, if
metal plug is chosen -
(SS Plug for CS Lower
and Tantalum Clad)
11 11
11 11
11 11
11 11
c
c
(non-asbestos)
Grafoil
Gasket
_ _ _ _ _ _ _ _ _ _ _ G
_ _ _ _ _ _ _ _ _ _ _ T
_ _ _ _ _ _ _ _ _ _ _ L
•
c
•
c
Teflon
Gylon 3510
d
d
Table II continued next page
* Caution:
Maximum working pressure of STR93D transmitter is 750 psi and STR94G transmitter
is 500 psig. Damage to sensor may result if pressure limit is exceeded.
**
Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
If Table III Bolt/Nut option is chosen, Seal bolts will ship as same material, and MAWP may change.
***
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 22
STR9xx
3D 4G
TABLE II - SEALS (continued)
Diaphragm
Diameter
Flange Size
Pressure Rating
Selection
g
1.9"
2.4"
2.9"
4.1"
2"
2-1/2"
3"
_ _ _ MD0 _ _ _ _ _ _
_ _ _ NE0 _ _ _ _ _ _
_ _ _ PF0 _ _ _ _ _ _
_ _ _ QG0 _ _ _ _ _ _
Selection
•
Customer clamp rating or 600 psi,
whichever is less
•
•
•
•
•
•
4"
Diaphragm
Body
Wetted Material
Sanitary Seal
316L SS
316 SS
_ _ _ _ _ _ N A _ _ _ _
•
•
•
•
•
•
•
•
Non-Wetted Material
No Selection
_ _ _ _ _ _ _ _ 0 _ _ _
Bolts
Styles
Gasket
No Selection
Tri-Clover Tri-Clamp
No Selection
_ _ _ _ _ _ _ _ _ 0 _ _
_ _ _ _ _ _ _ _ _ _ 8 _
_ _ _ _ _ _ _ _ _ _ _ 0
•
•
•
•
Seal Pressure Rating * *
Diaphragm
Size and
Selection
Diameter Bolt Pattern
C.S. Bolts
304 SS Bolts
2.4"
_ _ _ RFK _ _ _ _ _ _
_ _ _ RGK _ _ _ _ _ _
_ _ _ RPK _ _ _ _ _ _
_ _ _ RQK _ _ _ _ _ _
•
•
•
•
•
•
•
•
for 3" Pipe ?
8-Bolt
1500 psi
1250 psi
1500 psi
4" pipe
Design
2.4"
for 3" Pipe ?
6-Bolt
1250 psi
4" pipe
Design
Selection
Diaphragm
316L SS
Lower Housing
Carbon Steel
316 SS
_ _ _ _ _ _ RA _ _ _ _
_ _ _ _ _ _ RB _ _ _ _
_ _ _ _ _ _ RC _ _ _ _
_ _ _ _ _ _ RD _ _ _ _
_ _ _ _ _ _ SB _ _ _ _
_ _ _ _ _ _ SC _ _ _ _
Selection
•
•
•
•
•
•
•
•
•
•
•
•
316L SS
Wetted Material
Hastelloy C
Hastelloy C
316L SS
316 SS
Saddle Seal
Hastelloy C
N/A-Body Only
N/A-Body Only
Bolts *, ***
Hastelloy C
Body
Non-Wetted Material
Carbon Steel
304 SS
1
1
Carbon Steel
316 SS
_ _ _ _ _ _ _ _ B _ _ _
_ _ _ _ _ _ _ _ C _ _ _
_ _ _ _ _ _ _ _ _ 0 _ _
_ _ _ _ _ _ _ _ _ _ 0 _
_ _ _ _ _ _ _ _ _ _ _ K
•
•
•
•
•
•
•
•
No Selection
Styles
No Selection
No Selection
Klinger C-4401
(non-asbestos)
Grafoil
Gasket
_ _ _ _ _ _ _ _ _ _ _ G
_ _ _ _ _ _ _ _ _ _ _ T
_ _ _ _ _ _ _ _ _ _ _ L
•
•
•
•
•
•
Teflon
Gylon 3510
*
Bolts are not included with "Body only" selection.
Caution: Maximum working pressure of STR93D transmitter is 750 psi and STR94G transmitter
is 500 psig. Damage to sensor may result if pressure limit is exceeded.
**
***
If Table III Bolt/Nut option is chosen, Seal bolts will ship as same material, and MAWP may change.
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 23
STR9xx
3D 4G
TABLE III - OPTIONS
Selection
None
00
•
•
Communication Options
HART 5.x Protocol Compatible Electronics
HART 6.x Protocol Compatible Electronics
FOUNDATION Fieldbus Communications
Indicating Meter Options
Analog Meter (0-100 Even 0-10 Square Root)
Smart Meter
Custom Configuration of Smart Meter
Local Zero
Local Zero and Span
HC
H6
FF
e
e
r
e
e
r
b
b
ME
SM
CI
LZ
ZS
•
•
m
x
s
•
•
m
x
s
Transmitter Housing & Electronics Options
NAMUR Failsafe Software
SIL 2 - TÜV Certified transmitter (requires HC and WP options)
Lightning Protection
Custom Calibration and I.D. in Memory
Transmitter Configuration
15 15
14 14
NE
SL
LP
CC
TC
WP
WX
SH
A1
•
•
•
•
•
•
Write Protection (Delivered in the "enabled" position)
Write Protection (Delivered in the "disabled" position)
316 SS Electronics Housing - with M20 Conduit Connections
1/2" NPT to M20 316SS Conduit Adapter (BASEEFA EEx d IIC)
1/2" NPT to 3/4" NPT 316 SS Conduit Adapter
Stainless Steel Housing with M20 to 1/2" NPT 316 SS Conduit
Adapter (use for FM and CSA Approvals)
Stainless Steel Customer Wired-On Tag
(4 lines, 28 characters per line, customer supplied information)
Stainless Steel Customer Wired-On Tag (blank)
End Cap Live Circuit Warning Label in Spanish (only with ATEX 3D)
End Cap Live Circuit Warning Label in Portuguese (only with ATEX 3D)
End Cap Live Circuit Warning Label in Italian (only with ATEX 3D)
End Cap Live Circuit Warning Label in German (only with ATEX 3D)
Meter Body Options (Seal bolt material depends on Transmitter bolt material)
A286 SS (NACE) Bolts and 304 SS (NACE) Nuts for Heads
316 SS Bolts and 316 SS Nuts for Process Heads
B7M Bolts and Nuts for Process Heads
Remote Seal Options
•
•
b
b
•
•
n
n
u
i
n
n
u
i
A2
A3
TG
•
•
TB
SP
PG
TL
•
•
a
a
a
a
a
a
a
a
b
GE
CR
SS
B7
•
•
•
b
Gold Plated Seal Diaphragm (1 Seal)
G1
G2
N1
N2
j
j
j
j
j
j
Gold Plated Seal Diaphragm (2 Seals)
Teflon Coated Seal Diaphragm (1 Seal) - only for anti-sticking
Teflon Coated Seal Diaphragms(2 Seals) - only for anti-sticking
Transmitter Mounting Brackets Options
Mounting Bracket - Carbon Steel
b
b
MB
SB
FB
•
•
•
•
•
•
Mounting Bracket - 304 SS
Flat Mounting Bracket
Services/Certificates Options
UM
0X
TP
F1
F3
F5
F6
F7
F8
MT
Users Manual Paper Copy (Standard, HC or FF ships accordingly)
Clean Transmitter & Seals for Oxygen or Chlorine Service with Certificate
Over-Pressure Leak Test with F3392 Certificate
Calibration Test Report and Certificate of Conformance (F3399)
Certificate of Conformance (F3391)
Certificate of Origin (F0195)
FMEDA Certificate (SIL 1)
NACE Certificate (F0198)
•
h
•
•
•
•
•
o
16
2
•
h
•
•
•
•
•
•
b
b
NACE Certificate (F0198) for welded meter bodies only
Marine Type Approvals (DNV, ABS, BV & LR)
Warranty Options
2
Additional Warranty - 1 year
Additional Warranty - 2 years
Additional Warranty - 3 years
Additional Warranty - 4 years
W1
W2
W3
W4
•
•
•
•
•
•
•
•
b
Table III continued next page
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 24
STR9xx
3D 4G
TABLE III - OPTIONS (continued)
Approval
Body
Approval Type
Location or Classification
Selection
No hazardous location approvals
Explosion Proof
ꢀ
9X
•
Class I, Div. 1, Groups A,B,C,D
Dust Ignition Proof
Non-Incendive
Class II, III Div. 1, Groups E,F,G
Class I, Div. 2, Groups A,B,C,D
Class I, II, III, Div. 1, Groups
A,B,C,D,E,F,G
Factory
Mutual
1C
2J
•
•
•
•
Intrinsically Safe
Explosion Proof
Class I, Div. 1, Groups B,C,D
Class II, III, Div. 1, Groups E,F,G
Class I, II, III, Div. 1, Groups
A,B,C,D,E,F,G
Dust Ignition Proof
CSA
Intrinsically Safe
Intrinsically Safe
Non-Sparking
Intrinsically Safe,
Zone 0/1
Ex ia IIC T4
SA
(Australia)
4G
3S
3D
3N
•
•
•
•
•
•
•
•
Ex n IIC T6 (T4 with SM option)
b
EEx ia IIC T4, T5,T6
EEx d IIC T5, T6,
Enclosure IP 66/67
Flameproof, Zone 1
EEx nA, IIC T6
Non-Sparking,
Zone 2
ATEX*
(Honeywell). Enclosure IP 66/67
Ex II 1 G EEx ia IIC T4, T5, T6
Ex II 2 G EEx d IIC T5, T6
Ex II 3 G EEx nA, IIC T6 (Honeywell)
Enclosure IP 66/67
Multiple Marking**
Int. Safe, Zone 0/1, or
Flameproof, Zone 1, or
Non-Sparking, Zone 2
3H
6D
•
•
•
•
INMETRO
(Brazil)
Flameproof, Zone 1
Ex d IIC T5
*See ATEX installation requirements in the ST 3000 User's Manual
**The user must determine the type of protection required for installation of the equipment. The user shall then check the box [ꢀ]
adjacent to the type of protection used on the equipment certification nameplate. Once a type of protection has been checked on
the nameplate, subsequently the equipment shall not be reinstalled using any of the other certification types.
TABLE IV
Factory Identification
XXXX
•
•
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 25
RESTRICTIONS
Available Only With
Selection
Not Available With
Selection
Restriction
Letter
Table
Table
a
b
III
3D or 3H
Select only one option from this group
_ _ _ _ _ _ BF _ _ _ _,
_ _ _ _ _ _ BG _ _ _ _,
_ _ _ _ _ _ BH _ _ _ _,
_ _ _ _ _ _ JF _ _ _ _,
_ _ _ _ _ _ JG _ _ _ _,
c
II
_ _ _ _ _ _ BF _ _ _ _,
_ _ _ _ _ _ BG _ _ _ _,
_ _ _ _ _ _ JF _ _ _ _,
_ _ _ _ _ _ JG _ _ _ _,
II
II
d
e
III
4G
_ A _ _ _ _ _ _ _ _ _ _,
_ B _ _ _ _ _ _ _ _ _ _,
_ C _ _ _ _ _ _ _ _ _ _,
_ G _ _ _ _ _ _ _ _ _ _,
_ H _ _ _ _ _ _ _ _ _ _,
_ J _ _ _ _ _ _ _ _ _ _,
_ 2 _ _ _ _ _ _ _ _ _ _,
g
h
i
I, II
III
_ 2 _ - 2 _ _ _ _ _ _ _ _ _ _ _
1C or 2J
_ _ _ _ _ _ AF _ _ _ _
_ _ _ _ _ _ BF _ _ _ _
_ _ _ _ _ _ BG _ _ _ _
_ _ _ _ _ _ BH _ _ _ _
_ _ _ _ _ _ GG _ _ _ _
_ _ _ _ _ _ JF _ _ _ _
_ _ _ _ _ _ JG _ _ _ _
j
II
III
III
SM
CR
m
n
o
III
1C, 2J
DC704 and Syltherm 800
fills and close-couple require
SS seal upper.
_ _ _ BCA _ _ 5 _ _ _,
_ _ _ CAA _ _ 5 _ _ _,
_ _ _ CCA _ _ 5 _ _ _,
_ _ _ CCC _ _ 5 _ _ _,
_ _ _ DAA _ _ 5 _ _ _,
_ _ _ DCA _ _ 5 _ _ _,
_ _ _ DCC _ _ 5 _ _ _,
_ _ _ DGA _ _ 5 _ _ _,
_ _ _ DGC _ _ 5 _ _ _,
_ _ _ DDA _ _ 5 _ _ _,
_ _ _ _ _ _ GE _ _ _ _,
_ _ _ _ _ _ _ _ A _ _ _
_ _ _ _ _ _ _ _ B _ _ _
II
p
0 _ _ _ _ _ _ _ _ _ _ _ _,
2 _ _ _ _ _ _ _ _ _ _ _ _,
4 _ _ _ _ _ _ _ _ _ _ _ _
q
II
III
III
r
TC, ME, 4G, 3S
FF, ME
s
Restrictions continued next page
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 26
RESTRICTIONS - (continued)
Restriction
Letter
Available Only With
Selection
Not Available With
Selection
Table
Table
III
u
v
1C, 2J
I
2 _ _
II
w
x
_ _ _ _ _ _ JA _ _ _ _
III
FF, SM
III
MB, SB, FB
DC704 and Syltherm 800
fills and close-couple require
SS seal upper.
_ _ _ BCA _ _ 5 _ _ _,
_ _ _ CAA _ _ 5 _ _ _,
_ _ _ CCA _ _ 5 _ _ _,
_ _ _ CCC _ _ 5 _ _ _,
_ _ _ DAA _ _ 5 _ _ _,
_ _ _ DCA _ _ 5 _ _ _,
_ _ _ DCC _ _ 5 _ _ _,
_ _ _ DGA _ _ 5 _ _ _,
_ _ _ DGC _ _ 5 _ _ _,
_ _ _ DDA _ _ 5 _ _ _,
_ _ _ _ _ _ GE _ _ _ _,
_ _ _ _ _ _ _ _ A _ _ _
y
_ _ _ _ _ _ _ _ B _ _ _
2 _ _
I
II
_ A - M _ _ _ _ _ _ _ _ _ _
I
I
z
1
2
3
5
6
_ _ D
III
III
F7
FB
5 _ _, 1 _ _
II
II
_ _ _ _ _ _ _ _ _ _ _ 0
_ _ _ _ _ _ _ _ _ _ A _
1 _ _, 3 _ _
I
7
III
III
CR
8
9
CC,G1,G2,T1,T2,OX,TP,MT,WP
_ _ _ _ _ _ AA2_ _ _
_ _ _ _ _ _ AB2_ _ _
II
II
II
III
_ _ _ _ _ _ _ _ _ _ _ T
F7
_ _ _ _ _ _ _ _ _ _ 0 _
10
_ _ _ _ _ _JJG_ _ _
_ _ _ _ _ _JKG_ _ _
_ _ _ _ _ _JLG_ _ _
_ _ _ _ _ _CAA_ _ _
_ _ _ _ _ _CCA_ _ _
_ _ _ _ _ _CCC_ _ _
FF, 00
II
11
HC, WP
_ _ C
III
III
14
15
16
III
I
FF
See ST-83 for Published Specials with pricing.
See ST-89 and User's Manual for part numbers.
Notes:
See COMS Order Entry Information including TC, manuals, certificates, drawings and SPINS.
See ST-OD-1 for tagging, ID, Transmitter Configuration (TC) and calibration including factory default values.
To request a quotation for a non-published "special", fax RFQ with Application Data Sheet (34-ST-18-01) to Marketing Applications.
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 27
Dimensions and drawings
21a
21b
21b
21a
21a
21a
21a
21b
21b
21a
21a
21a
21a
21b
21b
21a
21a
21a
21a
21b
21b
21a
21a
21a
Figure 21a. Flush Flanged Seal
Figure 21b. Flush Flanged Seal
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 28
Dimensions and drawings, cont.
Figure 22
Figure 23
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 29
Dimensions and drawings, cont.
Figure 24
Figure 25
Figure 26
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 30
Dimensions and drawings, cont.
Figure 27
Figure 28
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 31
Dimensions and drawings, cont.
Figure 29
Figure 30
Figure 31
Download from Www.Somanuals.com. All Manuals Search And Download.
34-ST-03-57
Page 32
ST 3000® is a registered trademark of Honeywell International Inc.
HART* is a trademark of the Hart Communication Foundation.
FOUNDATION™ is a trademark of the Fieldbus Foundation.
Honeywell Process Solutions
Industrial Measurement and Control
Honeywell International Inc.
2500 W. Union Hill Drive
Phoenix, Arizona 85027
©Honeywell International Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|