Honeywell Home Security System 2 Partitioned Security System User Manual

ꢀ

$'(0&2ꢀ9,67$ꢁꢂꢃꢀ

ꢀꢁ3DUWLWLRQHGꢂ6HFXULW\ꢂ6\VWHPꢂ

ꢂ

3URJUDPPLQJ *XLGH

ꢀ

N7001PRV5 5/04 Rev A

Download from Www.Somanuals.com. All Manuals Search And Download.

Recommended Programming Procedure

The following is a step-by-step procedure recommended for programming your VISTA-40 system.

1. Set the keypads (and other peripheral devices) to the appropriate addresses.

2. Set factory defaults by pressing ✱97.

This will automatically enable keypad addresses 00-01, so be sure at least one keypad is set to one of these

addresses.

3. Program system-wide (global) data fields.

Using the programming form as a guide, enter program mode and program all system-wide programming

fields. These options affect the entire system, regardless of partitions. They include control options,

downloader and dialer options, RF options, event logging options, etc. Refer to the Program Field Index for a

listing of the program fields and their function.

Note that field 2✱00 (number of partitions) must be programmed before continuing.

4. Program partition-specific fields.

When the system-wide fields have been programmed, program all partition-specific programming fields by

first pressing ✱91 to select a partition (while still in data field program mode). Then enter the first partition-

specific field number ✱09. When you are finished, the next partition-specific field is automatically displayed.

Partition-specific fields can have different values for each partition. To program the fields for the next partition,

press ✱91, enter the desired partition number, then enter field ✱09. Refer to the MECHANICS OF

PROGRAMMING section in the ADEMCO VISTA-40 Installation and Setup Guide for detailed instructions.

5. Use #93 Menu Mode for device programming.

Refer to Device Programming in this guide to assign keypad ID numbers and default partitions for each

keypad, and to selectively suppress certain keypad sounding options. Also use this mode to assign RF

receivers, relay modules, and the VIP module.

6. Use #93 Menu Mode for zone programming.

Refer to Zone Programming in this guide to program zone response types, assign right loop zones and

wireless zones, assign zones to partitions, and to program alarm report codes.

7. Use #93 Menu Mode for programming relays.

Refer to Relay Programming in this guide to program desired relay operation.

8. Program Communication options.

Refer to System Communication section in the ADEMCO VISTA-40 Installation and Setup Guide for detailed

instructions. Then use #93 menu mode to program report codes.

9. Use #93 Menu Mode for programming alpha descriptors.

Refer to Alpha Programming in this guide to enter zone and partition descriptors and a custom installer’s

message.

10. Use #93 Menu Mode for relay voice descriptors and custom word substitutes.

Refer to Relay Voice Descriptors in this guide for further instructions for programming relay descriptors to be

annunciated by the VIP module, as well as the Custom Index section for custom word substitutes.

11. Define user access codes.

Refer to User Access Codes in the ADEMCO VISTA-40 Installation and Setup Guide to program authority

level, O/C reporting option, partition assignments, and RF key assignments for each user.

12. Exit Programming Mode.

Exit programming mode by pressing either ✱98 or ✱99. Additional entries of ✱99 are required if the exit is

being done from fields 1✱00 and above.

To prevent re-access to programming mode using the Installer’s code, use ✱98. The only way to re-access

programming mode is by depressing both the [✱] and [#] keys at the same time within 30 seconds of power-

up.

Exiting by using ✱99 always allows reentry into programming mode using the Installer code. Either way of

exiting allows access via downloading. Note that if local programming lockout is set via downloading,

programming mode cannot be entered at the keypad.

– 3 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Program Field Index

On the following pages, the programming fields have been arranged in numerical order. Use this index to cross-reference the

fields on the programming form.

Field

Group

Field Group

Communications

Field Group

# 93 Menu Mode

*00

*02

*03

*04

*05

*09

*10

*11

*12

*13

*14

*15

*16

*17

*19

*20

*21

*22

*23

*24

*25

*26

*27

*28

*29

*30

*31

*32

*33

*34

*35

*36

*37

*38

*39

*40

*41

*42

*43

*44

*45

*46

*47

*48

System-Wide

*49

*50

*51

*52

*53

*54

*55

*56

*57

*58

*59

*60

*61

*62

*63

*64

*65

*66

*67

*68

*69

*70

*71

*72

*73

*74

*75

*76

*77

*78

*79

*80

*81

*82

*83

*84

*85

*86

*87

*88

*89

*90

1*01

1*02

1*03

1*04

1*05

1*06

1*07

1*08

1*09

1*28

1*29

1*30

1*31

1*32

1*33

1*34

1*40

1*41

1*43

1*44

1*45

1*46

1*47

1*48

1*49

1*52

1*53

1*57

1*58

1*60

1*66

1*70

1*71

1*74

1*75

1*76

2*00

2*01

2*02

2*17

2*18

2*19

2*20

2*21

# 93 Menu Mode

Partition-Specific

System-Wide

Partition-Specific

System-Wide

Partition-Specific

System-Wide

Communications

Partition-Specific

System-Wide

# 93 Menu Mode

System-Wide

Communications

Partition-Specific

System-Wide

Partition-Specific

System-Wide

Partition-Specific

System-Wide

Partition-Specific

System-Wide

Partition-Specific

System-Wide

Partition-Specific

System-Wide

Partition-Specific

System-Wide

Communications

System-Wide

Partition-Specific

Communications

Partition-Specific

Communications

System-Wide

Partition-Specific

Communications

System-Wide

Communications

Partition-Specific

Communications

Partition-Specific

# 93 Menu Mode

– 4 –

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Programming Form

Some fields are programmed for each partition (shown as shaded fields). If you are programming a multiple-partition system,

see the Partition-Specific Fields section for programming these fields. Standard default (*97) values are shown in brackets.

*00 INSTALLER CODE

| | |

*25 BURG.TRIGGER FOR RESPONSE TYPE 8 [1]

Enter 4 digits, 0-9 [4140]

1=enable; 0=disable

*02 *05 RESPONSE TYPES FOR ZONES

*26 INTELLIGENT TEST REPORTING

[0]

Skip these fields. Use #93 Menu Mode, Zone

Programming to program the response types.

1=yes (no report sent if any other report was recently sent);

0=no (send report at programmed interval, field *27)

Must be 0 for UL installations.

*09 ENTRY DELAY #1

[02]

[03]

[06]

00, 02-15 times 15 seconds

Maximum "03" for UL.

*27 TEST REPORT INTERVAL

[024]

| |

Enter interval in hours, 001-199; 000=no report;

Max. 024 for UL installations.

*10 EXIT DELAY #1

00, 03-15 times 15 seconds

Maximum "04" for UL installations.

*28 POWER UP IN PREVIOUS STATE

[1]

[0]

1=yes; 0=no; "1" for UL installations.

*11 ENTRY DELAY #2

*29 QUICK ARM

00, 02-15 times 15 seconds (must be longer than Entry Delay

#1). Maximum "03" for UL installations.

1=yes; 0=no

*30 TOUCHTONE OR ROTARY DIAL

*12 EXIT DELAY #2

[08]

1=TouchTone; 0=rotary

00, 03-15 times 15 seconds (must be longer than Exit Delay

#1). Maximum "04" for UL installations.

*31 PABX ACCESS CODE

*13 ALARM SOUNDER DURATION

[04]

00-09; B-F (11-15)

01-15 times 2 minutes. Must be minimum 16 minutes for UL

installations.

*32 PRIM. SUBS. ACCT #

Enter 00-09; B-F (11-15) [15 15 15 15]

*14 ZONE 9 RESPONSE TIME

[0]

*33 PRIMARY PHONE NUMBER

Enter 1 for fast response time 10ms

Enter 0 for normal response time 350ms.

Must be 0 for UL installations.

*15 KEYSWITCH ASSIGNMENT

[0]

Enter 0-9 for each digit. Enter #11 for *, #12 for #,

#13 for 2 second pause

Enter partition in which keyswitch used,

1-2; 0=disable

*34 SECONDARY PHONE NUMBER

*16 CONFIRMATION OF ARMING DING

1=enable; 0=disable.

Must be "1" for UL Installations.

*17 AC LOSS KEYPAD SOUNDING

[0]

Enter 0-9 for each digit. Enter #11 for *, #12 for #,

#13 for 2 second pause

1=yes; 0=no

*35 DOWNLOAD PHONE NO.

*19 RANDOMIZE AC LOSS REPORT

1=10-40 min; 0=normal report (about 2 min. after AC loss).

*20 VIP MODULE PHONE CODE

Enter 0-9 for each digit. Enter #11 for *, #12 for #,

#13 for 2 second pause

Enter 01 - 09 for the first digit; enter

11 for “*” or 12 for “#” for the second digit.

Must be set to "0" for UL installations.

[00],

[11]

*36 DOWNLOAD ID NO.

*21 PREVENT FIRE TIMEOUT

[0]

Enter 00-09; A-F (10-15) [15 15 15 15 15 15 15 15]

1=No timeout; 0=Timeout.

*37 DOWNLOAD COMMAND ENABLES

*22 KEYPAD PANIC ENABLES

[001]

1=enable; 0=disable

995 996 999

Dlr ShtdwnSys ShtdwnNot UsedRmt BypRmt DisarmRmt ArmUpld PgmDwnld Pgm

See field 1*53 for Callback disable option; [1=enable];

0=disable. For UL installations, all entries must be "0."

*23 MULTIPLE ALARMS

[1]

1=yes; 0=no

*38 PREVENT ZONE XX BYPASS

[00]

*24 IGNORE EXPANSION ZONE TAMPER

[0]

01-64; 00 if all zones can be bypassed

1=Ignore; 0=Enable tamper for RF and RPMs.

Must be "0" for UL installations if using these devices.

– 5 –

Download from Www.Somanuals.com. All Manuals Search And Download.

*58 SUPERVISORY AND RESTORE CODES FOR ZONES

*39 ENABLE OPEN/CLOSE REPORT FOR

[0]

01-16. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]

INSTALLER CODE 1=enable; 0=disable

Trbl

Byp

*40 OPEN/CLOSE REPORT FOR KEYSWITCH [0]

Alarm Rst

Trbl Rst

Byp Rst

1=enable; 0=disable

*59 *62 ALARM REPORT CODES & ID DIGITS FOR

ZONES 17-32.

*41 NORMALLY CLOSED or EOLR (Zones 2-8) [0]

Skip these fields. Use #93 Menu Mode, Zone

Programming to program the report codes.

1=N.C.loops; 0=EOLR supervision.

Must be "0" for UL installations.

*63 SUPERVISORY AND RESTORE CODES FOR ZONES

17-32. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]

*42 DIAL TONE PAUSE

[0]

[1]

0=5 seconds; 1=11 seconds; 2=30 seconds.

Must be "0" UL Installations.

Alarm Rst

Trbl

Trbl Rst

Byp

Byp Rst

*43 DIAL TONE DETECTION

*64 *67 ALARM REPORT CODES & ID DIGITS FOR

ZONES 33-48.

1=wait for true dial tone; 0=pause, then dial

Skip these fields. Use #93 Menu Mode, Zone

Programming to program the report codes.

*44 RING DETECTION COUNT

[00]

*68 SUPERVISORY AND RESTORE CODES FOR ZONES

01-14; 15=answering machine; 00=no detection.

Must be "00" for UL Burglary.

33-48. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]

*45 PRIMARY FORMAT

[1]

Alarm Rst

Trbl

Trbl Rst

Byp

Byp Rst

0=Low Speed; 1=Contact ID; 2=ADEMCO High Speed;

3= ADEMCO Express

*69 *72 ALARM REPORT CODES & ID DIGITS FOR

ZONES 49-64.

*46 LOW SPEED FORMAT (Primary)

[0]

Skip these fields. Use #93 Menu Mode, Zone

Programming to program the report codes.

0= ADEMCO Low Speed; 1=Sescoa/Radionics

*73 SUPERVISORY AND RESTORE CODES FOR ZONES

*47 SECONDARY FORMAT

[1]

49-64. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]

0=Low Speed; 1=Contact ID; 2= ADEMCO High Speed;

3= ADEMCO Express

Alarm Rst

Trbl

Trbl Rst

Byp

Byp Rst

*48 LOW SPEED FORMAT (Sec.)

[0]

*74 *77 ALARM REPORT CODES & ID DIGITS FOR

0= ADEMCO Low Speed; 1=Sescoa/Radionics

ZONES 87-99.

Skip these fields. Use #93 Menu Mode, Zone

Programming to program the report codes.

*49 CHECKSUM VERIFICATION

[0] [0]

1=yes; 0=no

Prim

Sec

*78 SUPERVISORY AND RESTORE CODES FOR ZONES

87-99. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]

*50 SESCOA/RADIONICS SELECT

[0]

1=Sescoa; 0=Radionics

Alarm Rst

Trbl

Trbl Rst

Byp

Byp Rst

*51 DUAL REPORTING

1=yes; 0=no If used with Spilt Reporting "1" option (1*34),

alarms and alarm restores go to both primary & secondary

numbers, while all other reports go to secondary only. If used

with Split Reporting "2" option, alarms and alarm restores go to

both, open/close and test messages go to secondary only,

while all other reports go to primary.

ZONE TYPE RESTORE ENABLES

*79 FOR ZONE TYPES 1-8

*52 STANDARD/EXPANDED REPORT FOR PRIMARY

1=enable; [0=disable]

*80 FOR TYPES 9, 10

[0 0 0 0 0 0]

Alarm Rstr Byp Trbl O/C LoBat

0=standard; 1=expanded;

1=enable; [0=disable]

Note: Expanded overrides 4+2 format.

*53 STANDARD/EXPANDED REPORT FOR SECONDARY

[0 0 0 0 0 0]

Alarm Rstr Byp Trbl O/C LoBat

0=standard; 1=expanded;

Note: Expanded overrides 4+2 format.

*54 *57 ALARM REPORT CODES & ID DIGITS FOR

ZONES 01-16.

Skip these fields. Use #93 Menu Mode, Zone

Programming to program the report codes.

– 6 –

Download from Www.Somanuals.com. All Manuals Search And Download.

*80 *81

SYSTEM NON-ALARM CODES

Enter 00-09; B-F (11-15).

1*30 RF RCVR CHECK-IN INTERVAL

[06]

[12]

Default = 00 for all reports

02-15 times 2 hours; 00 disables supervision

*80 1st Digit

*81 2nd Digit

1*31 RF XMITTER CHECK-IN INTERVAL

02-15 times 2 hours; 00 disables transmitter supervision

1*33 TOUCHTONE W/ROTARY BACKUP

[0]

Open

1=enable; 0=disable

Low Battery

1*34 COMM. SPLIT REPORTING

[0]

Low Battery Restore

AC Loss

0=no; 1=alarms and alarm restores primary, others secondary;

2=open/close, test secondary, others primary. See 51 for

comments if using with dual reporting.

1*40 1*41 NON-ALARM DIALER CODES

Enter 00-09; B-F (11-15).

AC Restore

Test

Default = 00 for all reports

1*40 1st Digit

1*41 2nd Digit

Armed STAY

Power Up

Time/Date Set or Event Log Reset

Cancel

1*43 PERM. KEYPAD BACKLIGHT

[0]

Program Tamper

1=enable; 0=disable When disabled, display lights when any

key is pressed, and turns off after period of keypad inactivity.

*83 FIRST TEST REPORT TIME

1*44 WIRELESS KEYPAD TAMPER

[0]

[Day 00; hour 12; min 00] Days 01-07 Hours 00-23 Min 00-

59; 00 in all boxes = instant (Day 01= Monday)

DETECTION

1=enable; 0=disable.

Must be "0" for UL installations.

*84 SWINGER SUPPRESSION

[03]

01-15 alarms

Must be "00" (disabled) for UL.

*85 ENABLE DIALER REPORTS FOR PANICS & DURESS

1*45 EXIT DELAY SOUNDING

[0]

1=enable; 0=disable. Produces quick beeping during exit

delay if enabled.

NOTE: See page 32, “SOUND OPTION”, prompt for

disabling the entry/exit beeps on individual keypads.

1=enable; [0=disable]

995 996 999 Duress

1*46 AUXILIARY OUTPUT MODE

[0]

*87 ENTRY WARNING

[1]

Enter 0 for ground start output.

Enter 1 for open/close trigger.

Enter 2 for keypad-like sounding.

Enter 3 if AAV module is being used.

NOTE: Only one of the above options may be active within

the system.

1=continuous; 0=3 beeps

*86 4208 MODULE ZONE ASSIGMENT

[0]

1 = allows 8 zones on one module (10-17), but prevents any

other polling loop expansion. 0 = all other setups.

*88 BURG. ALARM COMM. DELAY

[0]

1*47 CHIME ON EXTERNAL SIREN

[0]

1=16 seconds; 0=no delay

Must be "0" for UL installations.

1=enable; 0=disable

1*48 WIRELESS KEYPAD ASSIGNMENT

[0]

*89 RESTORE REPORT TIMING

[0]

0=disable; enter partition in which RF keypad used, 1-2.

Must be "0" for UL installations.

0=Instant; 1=At bell timeout if zone is restored; 2=when

system is disarmed. Must be "0" for UL installations.

1*49 SUPPRESS TX SUPERVISION SOUND

[1]

*90 SEC. SUBS. ACCT #

1=disable; 0=enable.

Must be "0" for UL installations.

Enter 00-09; B-F (11-15) [15 15 15 15]

2nd Page Programming Fields (press *94)

1*52 SEND CANCEL IF ALARM + OFF

[0]

1*01 1*09 ASSIGN RESPONSE TYPE FOR ZONES.

1=no restriction; 0=within bell timeout period only

Skip these fields. Use #93 Menu Mode, Zone

Programming to program the response types.

1*53 DOWNLOAD CALLBACK

MISCELLANEOUS WIRELESS OPTIONS

1=callback not required; 0=callback required.

Fields 1*28 - 1*31 are not applicable for UL installations.

1*57 5800 RF BUTTON GLOBAL ARM

1*28 RF TX LOW BATTERY SOUND

[0]

1=enable; 0=disable

1=immediate; 0=when disarmed

1*29 RF TX LOW BATTERY REPORTING

[0]

1=enable; 0=disable

– 7 –

Download from Www.Somanuals.com. All Manuals Search And Download.

1*58 5800 RF BUTTON FORCE ARM

[0]

2*02 DAYLIGHT SAVING TIME

[1, 5]

Enter "1" to enable. If a zone is faulted after pressing button,

keypad will beep once. Pressing the button again within 4

sec. bypasses the zone. Enter "0" to disable.

Must be "0" for UL installations.

START/END WEEKEND

Enter 1-7. 1=first; 2=second; 3=third; 4=fourth; 5=last;

6=next to last; 7=3rd from last [1,5]

Start | End

2*17 NUMBER OF CODES PER PARTITION

1*60 ZONE 5 AUDIO ALARM VERIFICATION

[0]

Enter 1 If 2-way audio (AAV) is being used; Enter 0 if it is

not.

Enter 01-69 for each partition. The total must not exceed 70.

Must be "0" for UL installations.

2*18 ENABLE GOTO FOR THIS PARTITION

[0]

1=Allow log-on from other partition; 0=disable

1*66 SILENCE BELLS DURING AAV

[0]

Enter 1 to alarm sounders during AAV session.

Enter 0 to have alarm sounders continue to sound during

AAV session. Must be 0 for UL installations.

2*19 USE PARTITION DESCRIPTORS

0=disable; 1=enable

1*70 EVENT LOG TYPES

2*20 ENABLE J7 TRIGGERS FOR PARTITION [1]

0=disable for displayed partition; 1=enable for displayed

partition

[1 0 0 0 1]

Alarm Chk Byp O/C Syst

2*21 ENABLE SUPERVISION PULSES FOR LRR

1=enable; 0=disable

TRIGGER OUTPUTS

[000]

| |

1*71 12/24 HOUR TIME STAMP FORMAT

[0]

Used for supervised connection to 7920SE.

0=12 hour; 1=24 hour

Enter 0 to disable or 1 to enable the listed outputs.

F= Fire; B= Burglary; P= Silent Panic/Duress.

Must be 1 for UL. Installations.

1*74 RELAY TIMEOUT XXX MINUTES [000]

| |

Enter the relay timeout, 000-127 in multiples of 2 minutes,

desired for #93 Menu Mode Relay Programming output

command "56."

SUMMARY OF PROGRAMMING COMMANDS

To enter program mode, enter installer code + [8] + [0] +

[0]

1*75 RELAY TIMEOUT YYY SECONDS [000]

| |

•

Enter the relay timeout, 000-127 seconds for #93 Menu

Mode Relay Programming command "57."

•

To set standard defaults, press *97

To change to next page of program fields, press *94

To return to previous set of fields, press *99

To erase account and phone number field entries,

press [*] + field number + [*]

To assign zone descriptors, press #93 + follow menu

prompts

To add custom words, press #93 + follow menu prompts

To enter Installer's Message, press #93 + follow menu

prompts

1*76 ACCESS CONTROL RELAY

[00]

Relay will be pulsed for 2 seconds whenever code + [0] is

pressed. Enter 00-08; 00=none.

Must be "00" for UL.

•

3rd Page Programming Fields (press *94)

•

2*00 NUMBER OF PARTITIONS

[1]

Enter 1-2

•

To exit program mode, enter *99 OR *98: *99 allows re-

access to programming mode by installer code. *98

prevents re-access to programming mode by installer

code.

2*01 DAYLIGHT SAVING TIME [04, 10]

START/END MONTH

00-12; if no daylight saving time, enter 00,00

Start End

– 8 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Partition-Specific Fields

(Duplicate this page for each partition in the installation.)

To program these fields,

1. Press *91 to select a partition.

2. Enter a partition-specific field number (ex. *09).

3. Make the required entry.

4. Repeat steps 1-3 for the other partition in the system.

PARTITION #____ PROGRAM FIELDS

1st Page Fields

*88 BURG. ALARM COMM. DELAY

[0]

*09 ENTRY DELAY #1

[02]

[04]

[06]

[08]

[04]

1=16 seconds; 0=no delay. Must be "0" for UL installations.

00, 02-15 times 15 seconds.

Maximum 03 for UL Listed installations.

*90 SEC. SUBS. ACCT #

Enter 00-09; B-F (11-15) [15 15 15 15]

2nd Page Fields

*10 EXIT DELAY #1

00, 03-15 times 15 seconds.

Maximum 04 for UL Listed installations.

1*43 PERM. KEYPAD BACKLIGHT

[0]

1=enable; 0=disable When disabled, display lights when

any key is pressed, and turns off after period of keypad

inactivity.

*11 ENTRY DELAY #2

00, 02-15 times 15 seconds.

Maximum 03 for UL installations.

1*45 EXIT DELAY SOUNDING

[0]

*12 EXIT DELAY #2

1=enable; 0=disable. Produces quick beeping during exit

delay if enabled.

00, 03-15 times 15 seconds.

Maximum 04 for UL installations.

1*47 CHIME ON BELL 1

[0]

*13 ALARM SOUNDER DURATION

1=enable; 0=disable

01-15 times 2 minutes.

Must be minimum 16 minutes for UL installations.

1*52 SEND CANCEL IF ALARM + OFF

[0]

*16 CONFIRMATION OF ARMING DING

[0]

1=no restriction; 0=within Bell Timeout period only

1=enable; 0=disable.

Must be "1" for UL installations.

1*76 ACCESS CONTROL RELAY FOR PART.[00]

Relay will be pulsed for 2 seconds whenever code + [0] is

pressed. Enter 00-08; 00=none. Must be "00" for UL installs.

3rd Page Fields

*22 KEYPAD PANIC ENABLES

[001]

1=enable; 0=disable

995 996 999

[1]

2*18 ENABLE GOTO FOR THIS PARTITION

[0]

*23 MULTIPLE ALARMS

1=Allow log-on from other partitions; 0=disable

1=yes; 0=no. Must be 1 for UL installations.

2*20 ENABLE J7 TRIGGERS BY PARTITION

[1]

*29 QUICK ARM

[1]

0=disable; 1=enable for

1=yes; 0=no

*32 PRIM. SUBS. ACCT #

SUMMARY OF PROGRAMMING COMMANDS

Enter 00-09; B-F (11-15) [15 15 15 15]

•

To enter program mode, enter installer code + [8] + [0] +

[0]

*38 PREVENT ZONE XX BYPASS

[00]

•

To set standard defaults, press *97

To change to next page of program fields, press *94

To return to previous set of fields, press *99

To erase account and phone number field entries,

press [*] + field number + [*]

To assign zone descriptors, press #93 + follow menu

prompts

To add custom words, press #93 + follow menu prompts

To enter Installer's Message, press #93 + follow menu

prompts

001-64; 000 if all zones can be bypassed

*39 ENABLE OPEN/CLOSE REPORT

[1]

FOR INSTALLER CODE

1=enable; 0=disable

•

*84 SWINGER SUPPRESSION

[03]

01-15 alarms; Must be "00" (disabled) for UL installations.

•

*85 ENABLE DIALER REPORTS FOR PANICS & DURESS

1=enable; [0=disable]

995 996 999 Duress

•

To exit program mode, enter *99 OR *98: *99 allows re-

access to programming mode by installer code. *98

prevents re-access to programming mode by installer

code.

*87 ENTRY WARNING

[1]

1=continuous; 0=3 beeps

– 9 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming With #93 Menu Mode

NOTE: The following field should be preset before beginning: 2*00 Number of Partitions. In addition, receivers should

be programmed via Device programming.

After programming all system related programming fields in the usual way, press #93 while still in programming mode to

display the first choice of the menu driven programming functions. Press 0 (NO) or 1 (YES) in response to the displayed menu

selection. Pressing 0 will display the next choice in sequence.

For UL installations, verify that the audio alarm verification feature is disabled.

#93 MENU MODE KEY COMMANDS

The following is a list of commands used while in the menu mode.

#93

[4]

[#]

Enters Menu mode

Serves as ENTER key. Press to have keypad accept entry.

Backs up to previous screen.

Press to answer NO

Press to answer YES

01-09

All data entries are either 1-digit or 2-digit entries.

Exits menu mode, back into field programming mode, when entered at the first question for each category.

Menu selections are as follows:

PROMPT

EXPLANATION

For programming the following:

ZONE PROG?

1 = YES 0 = NO

•

Zone Number

Zone Response Type

Partition Number for Zone

Dialer report code for zone

Input Device Type for zone (whether RF, polling loop, etc.)

Enrolling serial numbers of 5800 Series transmitters & serial polling loop devices into the system.

Same as Zone Programming except:

EXPERT MODE?

1 = YES 0 = NO

•

Done with a minimum number of keystrokes.

Can program wireless keys using pre-defined templates.

For entering alpha descriptors for the following:

ALPHA PROG?

1 = YES 0 = NO

•

Zone Descriptors

Installer's Message

Custom Words

Partition Descriptors

Relay Descriptors

For defining the following device characteristics for addressable devices, including keypads, RF receivers

(5881), output relay modules (4204), and 4285/4286 VIP Module:

DEVICE PROG?

1 = YES 0 = NO

•

Device Address

Device Type

Keypad Options (incl. partition assignment)

RF House ID

For defining relay functions.

RELAY PROG?

1 = YES 0 = NO

For entering voice descriptors for relays to be used with the 4285/4286 VIP Module.

For creating custom word substitutes for VIP Module annunciation.

RLY VOICE DESCR?

1 = YES 0 = NO

CUSTOM INDEX ?

1 = YES 0 = NO

– 10 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Zone Programming

If using 5800 Series transmitters, do not the install batteries until you are ready to enroll them. After enrolling

the transmitter, the battery need not be removed. This is to prevent enrolling the wrong serial number.

PROMPT

EXPLANATION

Press 1 to enter ZONE PROGRAMMING mode. The following screens appear. Press [✱] to display the next

screen. Press # to display a previous screen.

ZONE PROG?

1 = YES 0 = NO

This prompt appears once upon entering Zone Programming Mode.

If “Yes,” Confirmation prompts will be displayed after the device’s Serial and Loop numbers have been

entered later.

SET TO CONFIRM?

1 = YES 0 = NO

Enter the 2-digit zone number to be programmed, as follows:

Protection Zones = 01–64

ENTER ZONE NO.

00 = QUIT

System Supervisory Zones = 88, 89, 90, 91, 92 (duress), 97

Keypad Panic Zones = 95, 96, 99

↑

Zone 10 entered

Press [✱] to continue.

This display appears, showing a summary of the zone's current programming. ZT = Zone Type, P =

Partition, RC = Report Code, In = the input type of device, and L = the device's loop number to which the

sensor is connected.

10 ZT

RC In L

10 00 1

Some devices can support more than one zone by means of individual loops (for example, 5801, 5804,

5816, 5817, etc.). If the zone is not programmed, the display appears as shown here. If you are checking a

zone's programming, and it is programmed satisfactorily, press [#] to back up one step and enter another

zone number, if desired.

Press [✱] to continue.

Each zone must be assigned a zone type, which defines the way in which the system responds to faults in

that zone. Refer to the Zone Type Definitions section in the ADEMCO VISTA-40 Installation and Setup

Guide for detailed definitions of each zone type. Enter the zone type desired (or change it, if necessary).

Available zone types are listed below.

10 ZONE TYPE

PERIMETER

Zone number 10 and Zone

Type 03 entry shown

00 = Assign for Unused Zones

01 = Entry/Exit #1, Burglary

02 = Entry/Exit #2, Burglary

03 = Perimeter, Burglary

04 = Interior Follower, Burglary

05 = Trouble Day/Alarm Night

06 = 24 Hr. Silent Alarm

08 = 24 Hr. Auxiliary

09 = Fire Without Verification

10 = Interior Delay, Burglary

20 = Arm–STAY†

21 = Arm AWAY†

22 = Disarm†

†

These are special zone

types used with 5800

Series Wireless

Pushbutton Units that

result in arming the system

in the STAY or AWAY

mode, or disarming the

system, depending on the

selection made.

23 = No Alarm Response

(e.g., relay activation)

07 = 24 Hr. Audible Alarm

Press [✱] to continue.

Enter the partition number (1–2) you are assigning this zone to.

Press [✱] to continue.

10 Partition

Enter the report code. The report code consists of 2 hexadecimal digits, each in turn consisting of 2

numerical digits. For example, for a report code of "3C," enter 03 for "3" and 12 for "C."

(Refer to the System Communication section in the Installation and Setup Guide for more information about

10 REPORT CODE

1st 03 2nd 12

report codes and reporting formats.)

Press [✱] to continue.

– 11 –

Download from Www.Somanuals.com. All Manuals Search And Download.

PROMPT

EXPLANATION

Enter the input device type as follows:

00 = not used

10 INPUT TYPE

RF Xmitter

01 = hardwired

Input types 4 & 5 are

valid for certain 5800

Series transmitters only

(e.g., 5801, 5802, 5802CP

& 5803).

03 = supervised RF transmitter (RF type)

04 = unsupervised RF transmitter (UR type)

05 = RF button-type transmitter (BR type)

06 = serial number polling loop device (SL type)

07 = DIP switch-type polling loop device

08 = right loop of DIP switch type device

Right loops refer to the use of the right loop on a 4190WH Zone Expander Module and/or 4278 PIR, which

allow hardwired devices to be monitored by the polling loop.

If you are programming hardwired or DIP switch polling loop devices, the summary display appears after

completing this entry.

Press [✱] to continue.

For Serial Number entry and Loop Number entry, do one of the following:

a. Transmit two open and close (or close and open) sequences. For a button-type transmitter, press and

release the button, wait approximately 4 seconds, then press and release the button a second time.

10 INPUT S/N:

AXXX-XXXX

b. Manually enter the 7-digit serial number printed on a label on the transmitter, using the Alpha keypad.

Then press the [✱] key, the cursor moves to the “L” position. You can edit the loop number, if necessary.

When the loop number is acceptable, press [✱].

c. Press key [C] to copy the last serial number enrolled (used when programming a transmitter with several

input loops).

Press [✱] to accept.

The cursor will then move to the Loop column (L) with the previously entered/transmitted serial number

displayed.

Enter the loop number (refer to 5800 Series Transmitters Loop Designations below).

10 INPUT S/N:

A022-4064

To Delete an Existing Serial Number, enter 0 in the loop number field. The serial number will change to

“0”s.

If 0 was entered in error, simply re-enter the loop number or press [#], and the serial number will return to the

display.

Press [✱] to accept.

The system will then check for a duplicate serial/loop number combination.

If a duplicate serial/loop number combination is found, the keypad will emit a single long beep, and display

the serial number along with a “?” for the loop number, allowing you to re-enter the correct loop number.

If the serial/loop number combination is not a duplicate in the system, a display appears showing the serial

number and loop number entry.

10 INPUT S/N:

A022-4064

Press [✱] to continue.

– 12 –

Download from Www.Somanuals.com. All Manuals Search And Download.

5800 Series Transmitters Loop Designations

LOOP 3

LOOP 2

(REED)

LOOP 1

(PRIMARY)

LOOP 2

LOOP 1

LOOP 2

(AUX. CENTER)

LOOP 1

(TERMINALS)

LOOP

LOOP 3

LOOP 4

(AUX. RIGHT)

ALTERNATE

POSITION

FOR LOOP 2

YOU MUST

ENROLL THIS

BUTTON

5817

ENROLL AS "RF"

5816MN

ENROLL AS "RF"

5801

5802MN

ENROLL AS "UR" OR "RF"

LOOP 3

LOOP 2

(REED)

YOU MUST

ENROLL THIS

BUTTON

LOOP

LOOP 1

(TERMINALS)

LOOP 2

LOOP 1

LOOP 4

(REED)

LOOP 2

LOOP 1

LOOP 3

(TERMINALS)

(INTERNAL

SHOCK

YOU MUST

ENROLL THIS

BUTTON

SENSOR)

LOOP 3

(TERMINALS)

LOOP 4

5819S (WHS & BRS)

ENROLL AS "RF"

5819

ENROLL AS "RF"

LOOP 1

LOOP 3

5804

ENROLL

AS "BR"

•

• •

•

SET

HOUSE

CODE

• •

•

5827

SET HOUSE CODE

• •

5827BD

SET HOUSE CODE

•

5804BD

ENROLL AS "BR"

LOOP

5809

ENROLL AS "RF"

LOOP 2

(REED)

LOOP 1

(MOTION)

LOOP

(Green)

(Red)

(Yellow)

LOOP 1

(TERMINALS)

5808

ENROLL AS "RF"

5816

ENROLL AS "RF"

5850 (GBD)

ENROLL AS "RF"

5890

ENROLL AS "RF"

5800_trans_loop-V0

Note: For information on any transmitter not shown above, refer to the instructions accompanying that transmitter for

details regarding loop numbers, etc.

The 5802MN, 5802MN2, 5804, 5804BD, 5814, 5816TEMP, 5819, 5819WHS & BRS, 5827BD,

and 5850 transmitters are not intended for use in UL installations.

PROMPT

EXPLANATION

Confirmation Option: This prompt only appears if you answered “Yes” at the first prompt. The system

enters a confirmation mode so that the operation of the actual programmed input can be confirmed. Activate

the loop input or button that corresponds to this zone. At any time during this step, you may press the [✱] key

on the keypad to save the serial and loop number combination without confirming.

XMIT TO CONFIRM

PRESS ✱TO SKIP

If the serial number transmitted does not match the serial number entered, a display similar to the one

at the left appears. If the loop number does not match, it is also displayed.

Entd

Rcvd

A022-4063

A022-4064

If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary

display does not appear), press the [#] key twice and then enter or transmit the correct serial number.

If the serial number transmitted does match the serial number entered, the system beeps 3 times and a

summary display appears, showing that zone’s programming. Note that an “s” indicates that a transmitter’s

serial number has been enrolled.

10 ZT P RC In

03 3C RF 1s

Press [✱] to accept the zone information.

– 13 –

Download from Www.Somanuals.com. All Manuals Search And Download.

PROMPT

EXPLANATION

The system now returns to the “ENTER ZONE NO.” prompt for the next zone.

When all zones have been programmed, enter 00 to quit.

ENTER ZONE NO.

00 = QUIT

After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in

the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information

(zone number, zone type, etc.) relevant to that device.

When you have finished programming all zones, test each using the system’s Test Mode. Do not use the

Transmitter ID Sniffer Mode. The system checks only for transmission of one zone on a particular

transmitter, NOT the zones assigned to each additional loop, and also does not verify polling loop type

zones.

Expert Mode Zone Programming

Expert mode allows you to program zones using the minimum number of screens and keystrokes.

Enter the Programming mode with [Installer Code] + [8] [0] [0]

Before programming your zones, do the following:

1. Program field 2✱00: Number of Partitions.

2. Enable your RF Receiver in Device Programming menu mode.

To program your zones, press ✱93 to display the "ZONE PROG?" prompt. Enter 0 (NO) to each prompt until the “EXPERT

MODE?” prompt appears.

PROMPT

EXPLANATION

Press 1 to enter Expert mode.

EXPERT MODE?

1 = YES 0 = NO

This prompt appears once upon entering Expert Mode.

If you select “Yes,” Confirmation prompts will be displayed after the device’s Serial and Loop numbers have

been entered later.

SET TO CONFIRM?

0 = NO 1 = YES

A summary display appears, showing zone 1’s current programming or default values.

Zn ZT P RC In

01 03

10 HW

Enter the desired 2-digit zone number and press [✱].

Note: If you want to exit the Expert mode, enter 00 + [✱].

If an “s” appears after the loop number, it indicates that the transmitter’s serial number has been enrolled.

Use the [D] key to enter and duplicate wireless keys (see “Entering Wireless Keys” later)

Zn ZT

10 03

RC In

10 RF 1s

Enter all zone information except for Loop number, or press [C] to copy the zone information on this screen

from the last saved zone (including Loop).

Zn ZT

10 03

RC In

10 RF

ZT = Zone Type

= Partition

RC = Report Code

In = Input Device Type

= Loop number to which the sensor is connected.

NOTE: Pressing the [C] copies the zone information from the last saved zone, which includes the

input type. Verify this information is correct for this zone.

On this screen:

•

Use the [A] key to move to the right.

Use the [B] key to move to left and to back up to “ZT” field.

Press [✱] to accept the existing or newly entered zone information.

– 14 –

Download from Www.Somanuals.com. All Manuals Search And Download.

PROMPT

EXPLANATION

If you entered RF, BR, UR or SL for the Input Type, this screen displays. Otherwise the summary screen for

the next zone displays.

Enter the 7-digit serial number, using one of the following methods:

a. Transmit two open and close (or close and open) sequences. For a button-type transmitter, press and

release the button, wait approximately 4 seconds, then press and release the button a second time.

10 INPUT S/N:

A XXX-XXXX

b. Manually enter the 7-digit serial number printed on a label on the transmitter, using the alpha keypad.

Then press the [✱] key, the cursor will move to the “L” position. You can edit the loop number, if

necessary. When the loop number is acceptable, press [✱].

c. Press key [C] to copy the last serial number enrolled (used when programming a transmitter with several

input loops).

Remember, you can use the [A] key to move to the right or the [B] key to move to the left.

You can also use the [#] key to back up without saving.

Press [✱] to accept the serial number and advance to the “L” position (if method “a” or “c” was used), then

enter the loop number.

If necessary, press the [#] key to back up without saving, and re-enter or edit the serial number before

pressing [✱] to save

10 INPUT S/N:

A022-4064

The system checks for a duplicate. If a duplicate serial/loop number combination is found, the keypad will

emit a single long beep, and display the serial number along with a “?” for the loop number, allowing you to

re-enter the correct loop number.

To Delete an Existing Serial Number, enter 0 in the loop number field. The serial number will change to

“0”s.

If 0 was entered in error, simply re-enter the loop number or press [#], and the serial number will return to the

display.

10 INPUT S/N:

A000-0000

The prompt to confirm appears. This prompt only appears if you answered “Yes” at the “SET TO

CONFIRM?” prompt.

XMIT TO CONFIRM

PRESS ✱TO SKIP

The system enters a confirmation mode so that the operation of the actual programmed input can be

confirmed. Activate the loop input or button that corresponds to this zone. At any time during this step, you

may press the [✱] key on the keypad to save the serial and loop number combination without confirming.

If the serial number transmitted does not match the serial number entered, a display similar to the one

at the left appears. If the loop number does not match, it also is displayed.

Entd

Rcvd

A022-4063

A022-4064

If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary

display for the next zone does not appear), press the [#] key twice and then enter or transmit the correct

serial number.

Activate the button on the wireless key again after re-entering the serial number.

If the serial number transmitted matches the serial number entered, the system beeps 3 times and

advances to the summary display for the next zone's programming.

RC In

00 1

After all the zones have been programmed, enter 00 for the zone number to quit.

After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in

the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information

(zone number, zone type, etc.) relevant to that device.

Entering Wireless Keys

If you pressed the D key previously to enter defaults for 5804 and/or 5804BD wireless keys, the following screens appear:

PROMPT

EXPLANATION

Enter template number (1–6).

FROM TEMPLATE

1–3 = 5804 templates; 4–6 = 5804BD templates. See the defaults provided for each template in the chart

that follows these procedures.

1–6

Select from templates. Press [✱] to display template (template 1 shown selected).

Note: If necessary, press [#] to back up and re-enter template number.

Press [#] if you want to return to zone attributes screen.

When you press [✱], the selected template is displayed.

Top line of display represents loop numbers; bottom line represents zone type.

Press [✱] to accept template.

01 02 03 04

ZT 23 22 21 23

– 15 –

Download from Www.Somanuals.com. All Manuals Search And Download.

PROMPT

EXPLANATION

Enter partition number for wireless key.

Press [✱] to continue.

PARTITION

The system searches for the highest available, consecutive 4-zone group (the four zones required for the

5804 and 5804BD), and displays the lowest zone number of the group.

If you want to start at a different zone number, enter the zone desired and press [✱].

If that zone number is displayed, the system has the required number of consecutive zones available,

beginning with the zone you entered. If not, the system again displays a suggested zone that can be used.

If the required number of consecutive zones is not available at all, the system will display “00.”

Press [✱] to accept.

ENTER ZONE NO

00 = QUIT

Example of zone number

suggested by the system.

This indicates that zones

24, 25, 26, and 27 are

available.

To enter the serial number:

Press and release a button on the wireless key.

24 INPUT S/N

AXXX-XXXX

Manually enter the 7-digit serial number printed on the device’s label.

Press [✱] to accept serial number. The system checks for a duplicate.

If a duplicate exists, a long error beep will sound and the serial number reverts back to all “X”s allowing

you to re-enter the serial number.

Use the [A] key to move forward within the screen, and the [B] key to back up.

If you entered YES previously at the SET TO CONFIRM prompt (see first prompt following entry into the

Expert Programming Mode), the display on the left appears.

To confirm, activate the button on the wireless key that corresponds to this zone.

XMIT TO CONFIRM

PRESS ✱TO SKIP

If the serial number transmitted does not match the serial number entered, a display similar to the one

at the left appears.

If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary

display does not appear), press the [#] key and then enter the correct serial number.

Entd

Rcvd

A022-4063

A022-4064

Activate the button on the wireless key again after re-entering the serial number.

If the serial number transmitted matches the serial number entered, the system will beep 3 times and

revert to the "Start Zone No." prompt and will show the lowest numbered zone of the next available 4-zone

group (4 consecutive zones) that is available for programming.

ENTER ZONE NO

00 = QUIT

After all the wireless keys have been entered, enter 00 for the zone number to quit.

After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in

the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information

(zone number, zone type, etc.) relevant to that device.

Wireless Key Default Templates

5804

5804BD

Template 1

Loop Function

Zone Type Template 4

Loop

Function

Zone Type

No Response

Arm AWAY

Disarming

Arm AWAY

No Response

Template 2

Template 3

Loop Function

Zone Type Template 5

Loop

Function

Zone Type

No Response

Arm STAY

Arm AWAY

Disarming

Arm AWAY

Arm STAY

Loop Function

Zone Type Template 6

Loop

Function

Zone Type

24-Hour Panic

Arm STAY

Arm AWAY

Disarming

Arm AWAY

Arm STAY

– 16 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Alpha Descriptors Programming

You can program a user-friendly English language description/location for all protection zones, relays, keypad panics, polling

loop short, and RF receiver supervision troubles.

Each description can be composed of a combination of words (up to 3) that are selected from a vocabulary of 244 words

stored in memory, and any word can have an "s" or " ’s " added to it. In addition, up to 20 installer-defined words can be added

to those already in memory. Thus, when an alarm or trouble occurs in a zone, an appropriate description for the location of

that zone will be displayed at the keypad.

NOTE: Due to the use of 2-digit zone numbers, the first word of the descriptor is limited to 7 characters if you want it to fit on

the top line of the display.

A custom installer’s message can be programmed for each partition, which is displayed when the system is "Ready" (e.g., THE

PETERSONS’).

1. To program alpha descriptors, enter Programming mode, then press [#]93 to display "ZONE PROG?"

2. Press 0 (NO) twice to display "ALPHA PROG?".

3. Press 1 to enter Alpha Programming.

There are 5 submenu selections that will be displayed one at a time.

Press 1 to select the mode desired. Press 0 to display the next mode available. The alpha menu selections are:

ZONE DESCRIP?

DEFAULT SCREEN?

CUSTOM WORD?

PART DESCRIP?

EXIT EDIT MODE?

For entering zone descriptors.

For creating custom message; displayed when system is ready.

For creating custom words for use in descriptors.

For creating 4-character partition names.

Press 1 to exit back to #93 Menu Mode.

4. Refer to the sections that follow for procedures for adding alpha descriptors.

Zone Descriptors

1. Select ZONE DESCRIPTOR mode.

The keypad keys perform the following functions:

[3] Scrolls both alphabet and actual words in ascending alphabetical order.

[1] Scrolls both alphabet and actual words in descending alphabetical order.

[2] Adds or removes an "s" or " 's " to a vocabulary word.

[6] Switches between alphabet and actual word list; used to accept entries.

[8] Saves the zone description in the system's memory.

[#] [#] plus zone number displays the description for that zone.

2. Enter the zone number to which you want to assign a descriptor.

For example, key [✱] 01 to begin entering the description for Zone 1, (key [✱] 02 for Zone 2, [✱] 03 for Zone 3, etc.). The

following is displayed: ✱ ZN 01 A.

Note that the first letter of the alphabet appears after the zone number, and that the zone number is automatically

included with the description.

3. Enter the descriptor for that zone.

Use one of two methods as follows:

(Assume, for example, that the desired description for Zone 1 is BACK DOOR.)

a) Press [#] followed by the 3-digit number of the first word from the fixed dictionary shown later in this section (e.g.,

[0][1][3] for BACK).

Press 6 in order to accept the word and proceed, or press 8 to store the complete descriptor and exit;

b) Select the first letter of the desired description (note that "A" is already displayed). Use the 3 key to advance through

the alphabet and the 1 key to go backward.

Press 3 key repeatedly until "B" appears (press 1 to go backwards if you happen to pass it), then press 6 to display

the first available word beginning with “B”.

Press 3 repeatedly to advance through the available words until the word “BACK” is displayed.

To add an "s" or " 's" if you need to, press 2. The first depression adds an "s," the second depression adds

an " 's, " the third depression displays no character (erases the " 's"), the fourth depression adds an "s," etc.

– 17 –

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Accept the word.

To accept the word, press 6, which switches back to the alphabet list for the next word, or press 8 to store the complete

descriptor and then exit.

5. Select the next word.

For selection of the next word (DOOR), repeat step 3a (word #057) or 3b, but selecting the word "DOOR.”

To accept the word, press 6, which again switches back to alphabet list.

6. Store the descriptor.

When all desired words have been entered, press 8 to store the description in memory.

To review the zone descriptors, key [#] plus zone number (e.g., #01).

To edit zone descriptors, key [✱] plus zone number (e.g., ✱01)

7. Exit Zone Description Mode: enter 00.

Default Screen (Custom Message Display)

Normally, when the system is in the disarmed state, the following display is present on the keypad.

****DISARMED****

READY TO ARM

Part or all of the above message can be modified to create a custom installer message for each partition. For example,

“****DISARMED****” on the first line or “READY TO ARM” on the second line could be replaced by the installation company

name or phone number for service.

Note: There are only 16 character spaces on each of the two lines.

To create a custom display message, proceed as follows:

1. Select Default Screen mode.

The keypad asks for the partition number for this message.

Enter the partition number. Press [✱] to accept entry.

The following display appears:

****DISARMED****

READY TO ARM

A cursor is present at the extreme left of the first line (over the first "star"). Press 6 to move the cursor to the right and 4 to

move the cursor to the left. Press 7 to insert spaces or erase existing characters.

2. Create the message.

For example, to replace “READY TO ARM” with the message “SERVICE 424-0177,” proceed as follows:

Press 6 to move the cursor to the right, and continue until the cursor is positioned over the first location on the second

line.

Press 3 to advance through the alphabet to the first desired character (in this case, "S"). Press 1 to go backward, when

necessary. When the desired character is reached, press 6.

The cursor then moves to the next position, ready for entry of the next character (in this example, "E"). When the cursor

reaches a position over an existing character, press 3 or 1 to advance or back up from that character in the alphabet.

Proceed in this manner until all characters in the message have been entered.

3. Save the message.

Store the new display message in memory by pressing 8.

4. The system asks for a new partition number.

Enter 0 to quit or 1-2 for a new partition number.

Custom Words

Up to 20 installer-defined words can be added to the built-in vocabulary. Each of the 20 "words" can actually consist of several

words, but bear in mind that a maximum of 10 characters can be used for each word string.

1. Select CUSTOM WORD Mode.

The keys perform the following functions:

[3] Advances through alphabet in ascending order.

[1] Advances through alphabet in descending order.

[6] Selects desired letter; moves the cursor 1 space to the right.

[4] Moves the cursor one space to the left.

[7] Inserts a space at the cursor location, erasing any character at that location.

[8] Saves the new word in the system's memory.

[✱] Returns to Description Entry Mode.

– 18 –

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Enter the custom word number (01-20) you want to create.

For example, if you are creating the first word (or word string), enter 01; when creating the second word, enter 02, and so

on. A cursor now appears at the beginning of the second line.

3. Type the word using one of two methods as follows:

a) Press [#], followed by the 2-digit entry for the first letter you would like to display (e.g., 65 for "A").

When the desired character appears, press 6 to select it. The cursor will then move to the right, in position for the

next character. Press [#] plus the 2-digit entry for the next letter of the word.

b) Press 3 to advance through the list of symbols, numbers, and letters.

Press 1 to move back through the list.

When you have reached the desired character, press 6 to select it. The cursor then moves to the right, in position for

the next character.

4. Repeat step 3 to create the desired custom word (or words).

Press 4 to move the cursor to the left if necessary.

Press 7 to enter a blank (or to erase an existing character).

Each word or word string cannot exceed 10 characters.

5. Save the word by pressing 8.

This returns you to the “CUSTOM WORD?” display. The custom word (or string of words) is automatically added to the

built-in vocabulary at the end of the group of words beginning with the same letter.

Custom words are retrieved as word numbers 250 to 269 for words 1 to 20, respectively, when using method 3a to enter

alpha descriptors.

When using method 3b to enter alpha descriptors, each word appears at the end of the group of words that begin with the

same letter as it does.

6. Repeat steps 2 through 6 to create up to a maximum of 20 custom words (or word strings).

7. Exit Custom Word Mode by entering 00 at the “CUSTOM WORD” prompt.

Partition Descriptors

1. Select "Part DESCRIPT." Mode.

The system asks for the partition number desired. Enter the number as a single-key entry 1-2.

2. Follow the same procedure as for custom words.

Note: The partition descriptors are limited to 4 characters (e.g., WHSE for warehouse).

– 19 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Alpha Descriptor Vocabulary

(For entering alpha descriptors. To select a word, press [#] followed by the word’s 3-digit number.)

NOTE: This vocabulary is not to be used for relay voice descriptors. See the Relay Voice Descriptors section when

programming relay voice descriptors.

000 (Word Space)

001 AIR

002 ALARM

003 ALCOVE

004 ALLEY

005 AMBUSH

006 AREA

007 APARTMENT

008 ART

•

052 DETECTOR

053 DINING

054 DISCRIMINATOR

055 DISPLAY

056 DOCK

057 DOOR

058 DORMER

059 DOWN

060 DOWNSTAIRS

061 DRAWER

062 DRIVEWAY

063 DRUG

102 INTERIOR

103 INTRUSION

151 POLICE

152 POOL

153 POWER

202 TRANSMITTER

203 TRAP

•

104 JEWELRY

105 KITCHEN

204 ULTRA

205 UP

•

154 QUAD

•

206 UPPER

207 UPSTAIRS

208 UTILITY

209 VALVE

210 VAULT

211 VIBRATION

212 VOLTAGE

•

106 LAUNDRY

107 LEFT

108 LEVEL

109 LIBRARY

110 LIGHT

111 LINE

112 LIQUOR

113 LIVING

114 LOADING

115 LOCK

155 RADIO

156 REAR

157 RECREATION

158 REFRIG

159 REFRIGERATION

160 RF

161 RIGHT

162 ROOM

163 ROOF

•

009 ATTIC

010 AUDIO

011 AUXILIARY

•

064 DUCT

•

012 BABY

013 BACK

014 BAR

015 BARN

016 BASEMENT

017 BATHROOM

018 BED

019 BEDROOM

020 BELL

021 BLOWER

022 BOILER

023 BOTTOM

024 BOX

025 BREAK

026 BUILDING

027 BURNER

•

213 WALL

214 WAREHOUSE

215 WASH

216 WEST

217 WINDOW

218 WINE

219 WING

220 WIRELESS

221 WORK

065 EAST

066 ELECTRIC

067 EMERGENCY

068 ENTRY

069 EQUIPMENT

070 EXECUTIVE

071 EXIT

116 LOOP

117 LOW

118 LOWER

164 SAFE

•

165 SCREEN

166 SENSOR

167 SERVICE

168 SHED

169 SHOCK

170 SHOP

171 SHORT

172 SHOW

173 SIDE

174 SKYLIGHT

175 SLIDING

176 SMOKE

177 SONIC

•

119 MACHINE

120 MAGNETIC

121 MAIDS

122 MAIN

123 MASTER

072 EXTERIOR

•

073 FACTORY

074 FAILURE

075 FAMILY

076 FATHERS

077 FENCE

078 FILE

079 FIRE

080 FLOOR

081 FLOW

222 XMITTER

223 YARD

•

124 MAT

•

125 MEDICAL

126 MEDICINE

127 MICROWAVE

128 MONEY

129 MONITOR

130 MOTHERS

131 MOTION

132 MOTOR

133 MUD

•

224 ZONE (No.)

225 ZONE

•

028 CABINET

029 CALL

030 CAMERA

031 CAR

032 CASE

033 CASH

•

178 SONS

•

226

227

•

179 SOUTH

180 SPRINKLER

181 STAMP

182 STATION

183 STEREO

184 STORE

185 STORAGE

186 STORY

187 STRESS

188 STRIKE

189 SUMP

082 FOIL

228 1ST

229

230 2ND

231

232 3RD

233

234 4TH

235

236 5TH

237

238 6TH

239

240 7TH

241

242 8TH

243

•

083 FOYER

084 FREEZER

085 FRONT

086 FUR

•

034 CCTV

•

134 NORTH

135 NURSERY

035 CEILING

036 CELLAR

037 CENTRAL

038 CIRCUIT

039 CLIP

040 CLOSED

041 COIN

087 FURNACE

•

088 GALLERY

089 GARAGE

090 GAS

•

136 OFFICE

137 OIL

138 OPEN

139 OPENING

140 OUTSIDE

141 OVERFLOW

142 OVERHEAD

•

091 GATE

190 SUPERVISED

191 SUPERVISION

192 SWIMMING

193 SWITCH

•

092 GLASS

093 GUEST

094 GUN

042 COLD

043 COATROOM

044 COLLECTION

045 COMBUSTION

046 COMPUTER

047 CONTACT

•

095 HALL

096 HEAT

097 HIGH

098 HOLDUP

099 HOUSE

143 PAINTING

144 PANIC

145 PASSIVE

146 PATIO

147 PERIMETER

148 PHONE

149 PHOTO

150 POINT

194 TAMPER

195 TAPE

196 TELCO

197 TELEPHONE

198 TELLER

199 TEMPERATURE

200 THERMOSTAT

201 TOOL

•

244 9TH

250 Custom Word 1

•

048 DAUGHTERS

049 DELAYED

050 DEN

269 Custom Word 20

•

100 INFRARED

101 INSIDE

051 DESK

•

CHARACTER (ASCII) CHART

(For Adding Custom Words)

(space)

’

(

)

;

Notes: This factory-provided vocabulary of words is subject to change.

Bulleted words in bold face type are those that are also available for use by the 4285/4286 VIP Module. If you are

using a VIP Module, and words other than these are selected for alpha descriptors, the Voice Module will not provide

annunciation of those words.

– 20 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Device Programming

This menu is used to program keypads, receivers, and relay modules, etc.

Device Address 00 is always set as an alpha keypad assigned to Partition 1 with no sounder suppression

options, and these settings cannot be changed.

From Data Field Programming mode, press [#]93 to display "ZONE PROG?" Press 0 repeatedly to display "DEVICE PROG?"

PROMPT

EXPLANATION

Press 1 to enter Device Programming.

DEVICE PROG?

1=YES 0=NO

The device address identifies the device to the control. Enter the 2-digit device address number to match

the device’s physical address setting (01-15).

NOTE: If using the 4285/4286 Voice Module, it must be used at Device Address 04.

DEVICE ADDRESS

01-15, 00=QUIT

Select the type of addressable device as follows:

DEVICE TYPE

0 = device not used

3 = RF receiver (5881)

1 = alpha keypad (6139/6160)

2 = fixed keypad (6137/6150)

Press [✱] to accept entry.

4 = output relay module (4204)

5 = voice (VIP) Module (4285/4286)

Alpha Keypad

PROMPT

EXPLANATION

If you selected device type 1 (alpha keypad) or 2 (fixed keypad), this prompt appears. Enter the addressable

device’s default partition number (1 to maximum number of partitions programmed for system in field 2*00).

This is the primary partition for the device.

01 CONSOLE PART.

Press [✱] to accept entry.

Keypads can be individually programmed to suppress arm/disarm beeps, entry/exit beeps and chime mode

beeps. This helps prevent unwanted sounds from disturbing users in other areas of the premises.

01 SOUND OPTION

Enter a number 00-03 for the keypad sounding suppression options desired for the keypad as follows:

00 = no suppression

01 = suppress arm/disarm & entry/exit beeps

02 = suppress chime mode beeps only

03 = suppress arm/disarm, entry/exit and chime mode beeps

Press [✱] to accept entry.

RF Expander

PROMPT

EXPLANATION

If you selected device type 3 (RF receiver), this prompt appears. Enter the 2-digit House ID (00-31). This is

required if you are using a wireless keypad (5827/5827BD).

01 RF EXPANDER

HOUSE ID

Press [✱] to accept entry.

VIP Module

PROMPT

EXPLANATION

If you selected device type 5 (VIP Module), this prompt appears. Enter the partition number 1-2 in which the

module is located.

Press [✱] to accept entry.

01 MODULE PART.

Press 00 + [✱] to exit Menu mode.

Press ✱99 to exit Program mode.

– 21 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Relay Programming

The system supports up to 8 relay outputs. Relays can be used to perform many different functions and actions. Each relay

must be programmed to begin one of three types of ACTIONS at a designated START event, and end that ACTION at a

designated STOP event. The options and prompts used to start and stop these devices are described below

The letter(s) in parentheses after each function described below, such as (A) after ACTION, are those that appear in the

various summary displays of programmed data during programming.

ACTION (A)

The "ACTION" of the device is how the device will respond when it is activated by the "START"

programming. You may want the device to activate momentarily, to pulse on and off continuously, or to

remain activated until some other event occurs to stop it. There are five different action choices:

•

ACTIVATE for 2 SECONDS and then reset.

ACTIVATE and REMAIN ACTIVATED until stopped by some other event.

PULSE ON and OFF until stopped by some other event.

NO RESPONSE when the device is not used.

START (STT)

The "START" programming determines when and under what conditions the device is activated. The

following START options are available:

1) EVENT (EV) is the condition (alarm, fault, trouble) that must occur to a zone or group of zones (zone

list) in order to activate the device. These conditions apply only when a zone list is used. The different

choices for "EVENT" are listed below and in “Programming Relays” later in this section.

•

ALARM

Action begins upon any alarm in an assigned zone in the zone list.

Action begins upon any opening of an assigned zone in the zone list.

Action begins upon any trouble condition in an assigned zone in the zone list.

Action is not dependent upon one of the above events.

FAULT

TROUBLE

NOT USED

ZONE LIST (ZL) is a group of zones to which the “EVENT” applies in order to activate a particular

device. Note that there are a total of 4 zone lists that can be programmed; when the selected EVENT

(alarm, fault or trouble) occurs in any zone in the selected “Start” ZONE LIST (1-4), activation of the

selected device will START.

3) ZONE TYPE/SYSTEM OPERATION (ZT). If all zones to be used to start the device have the same

response type, and there are no other zones of this type that are not to activate this device, then

“ZONE TYPE” may be used instead of a "ZONE LIST" and "EVENT” to activate the device.

If a system operation, such as “DISARMING” or “ANY FIRE ALARM,” is to activate the device, enter

the appropriate choice under the “ZONE TYPE” option.

The “ZONE TYPE/SYSTEM OPERATION” option functions independently of the “EVENT/ZONE

LIST” combination.

If a specific "ZONE TYPE" is chosen, any zone of that response type going into alarm, trouble, or fault

will cause the device to activate as selected in "ACTION.” If the same “ZONE TYPE” is also chosen for

the STOP programming, any zone of that type that restores will de-activate the device.

If a "SYSTEM OPERATION" is chosen, that operation will cause the device to activate as selected in

"ACTION.” The different choices for "ZONE TYPE" and "SYSTEM OPERATION" are listed in

“Programming Relays” later in this section, and on the Programming Form.

4) PARTITION NO. (P). The device's "Start" ZONE TYPE/SYSTEM OPERATION may be limited to an

occurrence on one partition (1-2), or any partition (0).

STOP (STP):

The "STOP" programming determines when and under what conditions the device is de-activated. The

following options are available:

1). RESTORE ZONE LIST (ZL). If a "ZONE LIST" is used as the “Stop” event, the device de-activates

when all the zones in that list restore from a previous fault, trouble, or alarm condition. This occurs

regardless of what is programmed to "START" the device; therefore, a "RESTORE ZONE LIST" is

normally only used when a "ZONE LIST" is used to start the device.

2). ZONE TYPE/SYSTEM OPERATION (ZT). Instead of using a "RESTORE ZONE LIST," you can select

a specific zone (response) type or system operation action to de-activate the device.

If you choose a specific "ZONE TYPE," any zone of that response type that restores from a previous

alarm, trouble, or fault condition will cause the device to de-activate.

If you choose a "SYSTEM OPERATION," that operation causes the device to de-activate. The

different choices for "ZONE TYPE" and "SYSTEM OPERATION" are listed in “Programming Relays”

later in this section, and in the Programming Form.

3) PARTITION NO. (P). The device's "Stop" Zone Type/System Operation may be limited to an

occurrence on one partition (1-2), or on any partition (0).

The “ZONE TYPE/SYSTEM OPERATION” option functions independently of the

“RESTORE/ZONE LIST” combination.

– 22 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Relay Output Devices Programming

From Data Field Programming Mode, press #93 to display the "ZONE PROG?" prompt. Press [0] (NO) to each menu option

until the "RELAY PROG?" prompt appears. Press [1] (YES).

While in this mode, press [✱] to advance to next screen. Press [#] to back up to the previous screen.

PROMPT

EXPLANATION

Enter the relay (output device) identification number 01-08. This is a reference number only, used for

identification purposes. The actual module address and relay number on the module are programmed in the

last two prompts.

ENTER RELAY #

(00=QUIT)

Press [✱] to continue.

02 A EV ZL P

STT 0 0 00

The keypad displays a summary STOP screen.

Press [✱] to continue.

ZL ZT

00 00

STOP

The Relay Action is the way in which the relay will respond when activated by the "start" event. Enter the

desired action for this relay as follows:

02 RELAY ACTION

NO RESPONSE

0=not used; 1=close for 2 secs.; 2=stay closed; 3=pulse on/off

A relay may be activated by an Event/Zone List combination, and/or by a Zone Type/System Operation. For

an Event/Zone List combination, enter the event code as follows:

02 START EVENT

NOT USED

0=not used; 1=alarm; 2=fault; 3=trouble

If you are not using a Zone List to activate the relay, enter 0.

Press [✱] to continue.

A zone list is a set of zones that can be used to initiate the start or stop relay action. If a zone list is being

used to start this relay action, enter the zone list number, 1-4. If a zone list is not being used, enter 0.

Press [✱] to continue.

02 START: ZN LIST

A Zone Type/System Operation can be used instead of or in addition to an Event/Zone List combination or

a specific zone to start the relay action. If a Zone Type/System Operation is being used, enter the 2-digit

code as listed in the table that follows.

02 START: ZN TYPE

NO RESPONSE

Press [✱] to continue.

Choices for Start/Stop Zone Types and System Operations:

00 = No Response (Not Used)

01 = Entry/Exit #1

02 = Entry/exit #2

03 = Perimeter

04 = Interior Follower

05 = Trouble Day/Alarm Night

06 = 24-Hr. Silent

23 = No Alarm Response

31 = End of Exit Time

32 = Start of Entry Time

33 = Any Burglary Alarm

34 = Code + [#] + 71 Key Entry

35 = Code + [#] + 72 Key Entry

36 = At Bell Timeout **

37 = 2 Times Bell Timeout **

38 = Chime

39 = Fire Alarm

40 = Bypassing

31 = End of Exit Time

41 = AC Power Fail

42 = System Battery Low

43 = Communication failure

44 = RF Low Battery

45 = Polling Loop Failure

51 = RF Receiver Failure

52 = Kissoff

54 = Fire Zone Reset

55 = Disarm + 1 Minute

56 = XX Minutes (enter XX in field 1*74) *

57 = YY Seconds (enter YY in field 1*75) *

58 = Duress

60 = Audio Alarm Verification (must be

selected for both START and STOP

operation)

07 = 24-Hr. Audible

08 = 24-Hr. Auxiliary

09 = Fire Alarm or Trouble

10 = Interior w/Delay

20 = Arming-STAY

21 = Arming-AWAY

22 = Disarming (Code + Off)

Stop condition only

** Or at disarming, whichever occurs earlier

If you are using options 56 and/or 57 (usually as the STOP Zone Type), you must program data fields 1*74

and 1*75 for the respective relay timeouts for minutes and seconds.

– 23 –

Download from Www.Somanuals.com. All Manuals Search And Download.

PROMPT

EXPLANATION

If the starting event will be limited to occurring on a specific partition, enter the partition number (1-2) in

which the start event will occur. Enter 0 for any partition.

Press [✱] to continue.

02 START: PARTN

ANY PARTITION

Do not use a zone programmed with an RF Button (Input Type BR) to STOP a relay. The system will not de-

activate the relay.

PROMPT

EXPLANATION

If a zone list is being used to stop this relay action, enter the zone list number, 1-4. The restore of a zone

on the zone list stops the relay. If a zone list is not being used, enter 0.

Press [✱] to continue.

02 STOP: ZN LIST

If a Zone Type/System Operation is being used to stop the relay action, enter the 2-digit code listed in the

Choices for Start/Stop System Operation chart.

Press [✱] to continue.

02 STOP: ZN TYPE

NO RESPONSE

This is the partition to which the stop condition will be limited. Enter 0 for any partition. Enter 1-2 for specific

partition number.

Press [✱] to continue.

02 STOP: PARTN

ANY PARTITION

The system may have some devices that are not intended to be under end user control, such as relays

activating fire doors or machinery. Enter 1 if the end user will be restricted from accessing this relay.

Press [✱] to continue.

02 RESTRICTION

1=YES 0=NO

Enter 1 for (ECP) relay modules (4204). Enter 2 for X-10 devices.

Press [✱] to continue.

02 RELAY TYPE

V-PLEX

If you selected 1 (4204), enter the actual module’s address (01-15) as set by its DIP switches. Up to 2

modules can be installed in a system.

Press [✱] to continue.

02 ECP ADDRESS

For 4204 Relay Outputs, enter the specific relay number on that module (1-4).

Press [✱] to continue.

02 MODULE RELAY#

The keypad will display the Start and Stop summary screens again.

Press [✱] to continue.

If you selected 2 for X-10 devices, enter the numerical equivalent of the House Code of the device, as

follows:

02 HOUSE CODE

A=00

B=01

C=02

D=03

E=04

F=05

G=06

H=07

I=08

J=09

K=10

L=11

M=12

N=13

O=14

P=15

Enter the numerical unit code of the X-10 device (00-15).

Press [✱] to continue.

02 UNIT CODE

The keypad displays the Start and Stop summary screens again.

Press [✱] to continue.

When all relays have been programmed, enter 00 at the "ENTER RELAY NO." prompt.

If you are defining a zone list, continue to the next section. If not, enter 00 + [✱] at the next two prompts. You will then be

asked "Quit Menu Mode?" Enter 1 for "Yes," 0 for "No." Then enter [✱]99 to exit programming completely.

Zone List Programming

After all relays have been programmed, upon entering 00 at the "ENTER RELAY NO." prompt, you are asked to enter a zone

list. If a zone list number was used to start or stop a relay, you must define the zones belonging to that list as follows:

PROMPT

EXPLANATION

Enter the zone list number 01-04. Enter 00 to quit.

ENTER Zn LIST ?

00=QUIT

– 24 –

Download from Www.Somanuals.com. All Manuals Search And Download.

PROMPT

EXPLANATION

Using 2-digit entries, enter each zone to be included in this zone list. Press [✱] after you enter each zone

number.

01 ADD ZONE #

00=QUIT

When you have entered all zones, enter 00.

Press [✱] to continue.

Enter 0 to save this zone list. Enter 1 to delete it.

01 Del Zn LIST ?

1=YES 0=NO

Enter 1 to delete one or more zones in that zone list. Enter 0 if no changes are necessary. If you enter 1,

the following screen appears; otherwise, the "Enter Zone LIST" prompt reappears.

01 DEL ZONES ?

1=YES 0=NO

Enter each zone number to be deleted from the zone list, pressing [✱] after each number.

01 Zn to DELETE ?

00=QUIT

This display appears if you pressed 00 at the “Enter Zone LIST” prompt. Enter the zone list number that you

wish to view.

Press [✱] to continue.

VIEW Zn LIST ?

00=QUIT

Press [✱] to scroll through all zones in that list. Enter 00 +[✱] to quit.

Press 1 to exit Menu Mode.

01 ASSIGNED ZONE

00=QUIT

Press [✱]99 to exit Program Mode.

Relay Voice Descriptors

If you are using the 4285/4286 VIP Module, you can program voice descriptors for each relay output. The descriptors are

announced by the voice module when you access the relays via the # 70 Relay Access Mode over the telephone.

Each voice descriptor can consist of up to 3 words selected from the Relay Voice Descriptors and Custom Word Substitutes

Vocabulary list (later in this section).

The index numbers from this vocabulary list are to be used for relay voice descriptors only. For normal

system voice annunciation (e.g., alarms, troubles, status), use the highlighted words in the alpha vocabulary

list in the Alpha Programming part of this guide.

To enter relay voice descriptors, do the following:

1. From Data Field Programming mode, press #93 to display the "ZONE PROG?" prompt.

2. Press 0 (NO) to each menu option until the "RLY VOICE DESCR?" prompt is displayed. Follow the instructions below.

While in this mode, press [✱] to advance to next screen. Press [#] to back up to previous screen.

PROMPT

EXPLANATION

Press 1 to program voice descriptors for relays.

RLY VOICE DESCR?

1=YES 0=NO

Enter the 2-digit relay number (01-08) for the relay desired, or enter 00 to quit Relay Voice Descriptor

Programming Mode.

Press [✱]

ENTER RELAY NO.

00=QUIT

From the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list, enter the 3-digit index

number for the first word of the relay descriptor phrase.

Press [✱] to accept entry.

01 ENTER DESC d1

01 ENTER DESC d2

01 ENTER DESC d3

From the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list, enter the 3-digit index

number for the second word of the relay descriptor phrase. If second word is not desired, press 000.

Press [✱] to accept entry.

From the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list, enter the 3-digit index

number for the third word of the relay descriptor phrase. If third word is not desired, press 000.

Press [✱] to accept entry. The “ENTER RELAY NO.” prompt appears. Enter the next relay number to be

programmed. When you have programmed all relay devices, enter 00 to quit.

Enter [✱]99 to exit Program Mode.

– 25 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Relay Voice Descriptors and Custom Word Substitutes Vocabulary

Word

Index Word

Index

Daughter’s................208

Den ..........................052

Detector....................128

Device......................060

Dim...........................163

Dining.......................031

Door .........................016

Down........................008

Downstairs ...............184

Driveway ..................130

Duct..........................131

Word

Index

Word

Index

Word

Index

Air ............................ 116

Alarm ....................... 255

And .......................... 067

Apartment ................ 117

Appliances ............... 161

Area ......................... 118

Attic.......................... 119

Front.........................087

No.............................165

North.........................146

Not............................012

Side .........................153

Six ...........................075

Sixth.........................219

Smoke .....................024

Son’s........................223

South.......................155

Stairs .......................006

Station .....................156

Storage....................157

Sun..........................154

System.....................062

Garage .....................023

Gas...........................138

Glass........................139

Off ............................011

Office........................147

On ............................058

One...........................070

Open.........................148

Outside.....................210

Hall...........................050

Heat..........................010

Baby......................... 120

Back......................... 121

Bar ........................... 122

Basement................. 021

Bathroom ................. 051

Battery...................... 053

Bed .......................... 092

Bedroom .................. 015

Blower...................... 123

Boiler........................ 124

Bright ....................... 162

Building.................... 125

Burglary.................... 039

Inside........................209

Kitchen .....................022

Panic ........................013

Partition ....................090

Patio.........................149

Phone.......................061

Power .......................063

Pump........................166

East..........................132

Eight.........................077

Eighth.......................221

Equipment................133

Exit...........................004

Temperature ............158

Third ........................159

Three .......................072

Tool .........................213

Two..........................071

Laundry ....................140

Left ...........................027

Library ......................141

Light .........................019

Living........................030

Loading.....................142

Lower .......................094

Factory.....................134

Father’s ....................211

Fence.......................135

Fifth..........................218

Fire...........................040

First .........................136

Five..........................074

Floor.........................029

Four..........................073

Fourth.......................217

Foyer........................137

Rear .........................088

Right.........................028

Room........................018

Up............................025

Upper.......................187

Upstairs ...................183

Utility........................185

Machine....................143

Master ......................144

Medical.....................014

Mother’s....................212

Motion ......................145

Call........................... 009

Central ..................... 089

Chime ...................... 054

Closed...................... 126

Computer ................. 127

Console.................... 066

’s...............................007

Second .....................056

Service .....................150

Seven .......................076

Seventh ....................220

Shed.........................151

Shop.........................152

West ........................215

Window....................017

Wing ........................216

Nine..........................078

Ninth.........................222

Zero.........................069

Zone ........................002

Custom Word Substitutes for VIP Module Annunciation

A substitute word can be programmed for each of the 20 custom words used in your alpha zone descriptions. The VIP Module

announces this substitute word in place of the custom word that is displayed on the alpha keypad. For example, a zone

display of "John’s Bedroom" could be announced as "Son’s Bedroom," as there is no annunciation for the custom word "John."

Note that if a substitute word is not assigned, the VIP Module will not annunciate the zone descriptor at all, but will only

annunciate the zone number.

To enter custom word substitutes, do the following:

1. From Data Field Programming Mode, press #93 to display the "ZONE PROG?" prompt.

2. Press [0] (NO) to each menu option until the "CUSTOM INDEX ?" prompt is displayed.

PROMPT

EXPLANATION

Enter 1 at this prompt.

CUSTOM INDEX ?

1=YES 0=NO

Enter the custom word number (01-20) for which a voice substitute is desired. Enter 00 to quit this

Programming Mode.

CUSTOM WORD NO.

00=QUIT

Press [✱] to accept entry.

Enter the 3-digit substitute word index number from the Relay Voice Descriptors and Custom Word

Substitutes Vocabulary list in the Relay Voice Descriptors part of this section.

01 ENTER INDEX #

Press [✱] to accept entry.

The "CUSTOM WORD NO." prompt is displayed. Enter the next custom word number to be substituted, or

enter 00 to quit.

– 26 –

Download from Www.Somanuals.com. All Manuals Search And Download.

System Layout Worksheets

Before programming any security system, you should first define the installation. To help you lay out a partitioned

system, use the following worksheets. This will further simplify the programming process.

PARTITIONS

Descriptor

(4-char max)

Prim.

Sub. #

Sec.

Sub. #

Alpha Default Message

(32-character maximum)

Partition #

Partition 1

Partition 2

Keyswitch Arming Partition Assignment (1-2):

Wireless Keypad Partition Assignment (1-2):

Voice Module Partition Assignment (1-2):

Use Partition Descriptor (yes/no)?

COMMUNICATION OPTIONS BY PARTITION

Part. 1

Option

Part. 2

Swinger Suppression Count 00-15; 00=no suppression

Cancel Report After Disarm

Dialer Reports for Panic (* + 1)

Dialer Reports for Panic (# + 3)

Dialer Reports for Panic (* + #)

Dialer Reports for Duress

Burglary Alarm Communications Delay (16 sec.)

SYSTEM DEFINITIONS BY PARTITION (enter values or yes/no)

Part. 1 Part. 2

Option

Entry Delay #1 (00, 30-225 seconds):

Exit Delay #1 (00, 45-225 seconds):

Entry Delay #2 (00, 30-225 seconds):

Exit Delay #2 (00, 45-225 seconds):

Quick Arming

Multiple Alarms per Arming

Console Panic for Zone 95 (* + 1)

Console Panic for Zone 96 (# + 3)

Console Panic for Zone 99 (* + #)

Allow Sign-on (GOTO function)

Non-Bypassable Zone*

Sounder Timeout Duration for Bell (2 min. increments)

Console Annunciation During Entry**

Console Annunciation During Exit

Confirmation of Arming Ding for Bell

Chime on Bell

Access Control Relay (field 1*76)

*Can be any zone 01-64.

**no = 3 beeps; yes = continuous

PRINTER OPTIONS

12- or 24-hour Time format

EVENT LOG TYPES

Option

Alarm

Yes

Trouble

Bypass

Open/Close

System

– 27 –

Download from Www.Somanuals.com. All Manuals Search And Download.

DEVICES (keypads, 4204, rf receivers, vip module, lrr)

Sound

Opt

House

Device Types:

Addr

Type

Part

00 = Device Not Used

01 = Alpha Console

02 = Fixed-Word Console

03 = RF Receiver

04 = Relay Module

05 = Voice Module

NOTES:

00.

01.

02.

03.

04.

05.

06.

07.

08.

09.

10.

11.

12.

13.

14.

15.

Address 04 must be used for the Voice Module,

if used.

Console Sounder Options:

0 = No Suppression

1 = Suppress Arm/Disarm and Entry/Exit Beeps

2 = Suppress Chime Mode Beeps Only

3 = Suppress Arm/Disarm, Entry/Exit and Chime

Mode Beeps

Defaults:

Addresses 00 = Alpha Keypad; No Suppression

Addresses 01 = Alpha Keypad; No Suppression

Addresses 02 = Alpha Keypad; No Suppression

Addresses 03 = Alpha Keypad; No Suppression

ACCESS CODES & USER DEFINITIONS FOR PARTITIONS 1 & 2

4-digit

Security

Code

Partition 1

Partition 2

2-Digit

User #

Auth.

Level

Open/

RF Key

2-Digit

User #

Auth.

Level

Open/

RF Key

Authority Levels: 1=Master (arm, disarm, bypass, and/or modify lower level users)

2=Manager (arm, disarm, bypass, and/or modify lower level users)

3=Operator A (arm, disarm, bypass)

4=Operator B (arm, disarm)

5=Operator C (arm, disarm only if system was armed with this code)

6=Duress code (arm, disarm, triggers silent panic alarm)

– 28 –

Download from Www.Somanuals.com. All Manuals Search And Download.

– 29 –

Download from Www.Somanuals.com. All Manuals Search And Download.

– 30 –

Download from Www.Somanuals.com. All Manuals Search And Download.

– 31 –

Download from Www.Somanuals.com. All Manuals Search And Download.

ZONE DEFINITIONS FOR KEYPAD PANIC ZONES 95, 96, & 99

Enter yes/no for each

partition (field *22)

Zone

No.

Zone

Type

Report

Code

Zone Information (part numbers) &

Alpha Descriptor (3 words max.)

ZONE DEFINITIONS FOR SYSTEM ZONES; 70, 88; 89, 90, 91 & 97

Zone Information (part numbers)

Zone

No.

Zone Report

Type Code

Alpha Descriptor (3 words max.)

Zone Types:

00=zone not used

01=entry/exit 1

02=entry/exit 2

03=perimeter

05=day/night burglary

06=24-hour silent

07=24-hour audible

08=24-hour auxiliary

09=supervised fire

10=interior (w/delay)

20=arm stay

21=arm away

22=disarm

23=no alarm response

04=interior (follower)

Input Types:

00=not used

05=RF button transmitter

01=hardwired

03=supervised RF transmitter

04=unsupervised RF transmitter

06=serial number polling loop

07=Dip switch-type polling loop

08=right loop dip switch polling loop

– 32 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Relay Outputs Worksheets

Applicable only if relays (4204) or X-10 devices are used.

ꢀ

Programmed in the #93 Menu Mode in the Relay Programming Section. Fill in the worksheet below and follow the

procedure in the installation instructions as you enter the data during the displays and prompts that appear in sequence.

Notes: 1. For 4204 the Device Programming section must be programmed for the device address. Set the DIP

switches on the device for that address.

2. For X-10 devices, use the 1361X10 transformer in place of the transformer that comes in the box with the

control panel.

Dev Add 4204

or House Code

for X-10

Relay # for 4204

Unit Code for X-10

1=4204

2=X-10

RELAY

DEV #

S T A R T

EV/ZL ZT / P

S T O P

ZL ZT / P

Restrict

A =

EV = EVENT

ZL = ZONE LIST

DEVICE ACTION

0 = No Response; 1 = Close for 2 sec; 2 = Close and stay closed; 3 = Pulse on and off

0 = Not used; 1 = Alarm; 2 = Fault; 3 = Trouble; 4 = Restore

1-4, 0 = Not Used

NOTES: "START" ZONE LIST: Upon alarm, fault, trouble or restore of ANY zone in this list, device action starts.

"STOP" ZONE LIST: Upon restore of ALL zones in this list, device action stops. It need not be same list as used for START.

ZT = ZONE TYPE/SYSTEM OPERATION

Choices for Zone Types are:

00=zone not used

01=entry/exit 1

02=entry/exit 2

03=perimeter

05=day/night burglary

06=24-hour silent

07=24-hour audible

08=24-hour auxiliary

09=supervised fire

10=interior (delay)

20=arm stay

21=arm away

22=disarm

23=no alarm response

04=interior (follower)

NOTE: Any zone in "ZT" for Start, going into alarm, fault, or trouble will activate the relay.

Any zone in "ZT" for Stop, that restores will stop the relay action.

Choices for System Operation are:

00 = No Response (Not Used)

01 = Entry/Exit #1

02 = Entry/exit #2

23 = No Alarm Response

31 = End of Exit Time

32 = Start of Entry Time

33 = Any Burglary Alarm

34 = Code + [#] + 71 Key Entry

35 = Code + [#] + 72 Key Entry

36 = At Bell Timeout **

37 = 2 Times Bell Timeout **

38 = Chime

39 = Fire Alarm

40 = Bypassing

31 = End of Exit Time

41 = AC Power Fail

43 = Communication failure

44 = RF Low Battery

45 = Polling Loop Failure

51 = RF Receiver Failure

52 = Kissoff

03 = Perimeter

04 = Interior Follower

05 = Trouble Day/Alarm Night

06 = 24-Hr. Silent

54 = Fire Zone Reset

55 = Disarm + 1 Minute

56 = XX Minutes (enter XX in field 1*74) *

57 = YY Seconds (enter YY in field 1*75) *

58 = Duress

60 = Audio Alarm Verification (must be

selected for both START and STOP

operation)

07 = 24-Hr. Audible

08 = 24-Hr. Auxiliary

09 = Fire Alarm or Trouble

10 = Interior W/Delay

20 = Arming-STAY

21 = Arming-AWAY

22 = Disarming (Code + Off)

42 = System Battery Low

Stop condition only

** Or at disarming, whichever occurs earlier

P =

PARTITION No. 1-2, 0 = Any

– 33 –

Download from Www.Somanuals.com. All Manuals Search And Download.

ZONE LISTS FOR RELAY DEVICES – Programmed in the #93 Menu Mode in the Relay Programming Section. Fill in the

required data on the worksheet below and follow the procedure shown earlier in this Programming Guide as you enter the

data during the displays and prompts that appear in sequence. Up to 4 zone lists may be created

Note: Record desired zone numbers below. More or fewer boxes than shown may be needed, as any list may include any or

all of system's zone numbers.

Zone List 1: Started or stopped by zone numbers (enter 00 to end entries).

Zone List 2: Started or stopped by zone numbers (enter 000 to end entries).

Zone List 3: Started or stopped by zone numbers (enter 000 to end entries).

Zone List 4: Started or stopped by zone numbers (enter 000 to end entries).

– 34 –

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Summary of Connections Diagram

P O L L I N G L O O P

( F a s t / N o r m a l ) L o o p

P r o g r a m m a b l e R e s p o n s e

B R E A K D E T E C T O R L O O P

L A T C H I N G T Y P E G L A S S

( A l s o s u p p o r t s N O / N C B u r g c o n t a c t s )

D E T E C T O R L O O P

2 - W I R E S M O K E

D a t a o u t

D a t a i n

N O C O N N E C T I O N

R E D ( + )

B L K ( - )

– 35 –

Download from Www.Somanuals.com. All Manuals Search And Download.

165 Eileen Way, Syosset, New York 11791

www.honeywell.com/security

¬1ꢀꢁꢁꢂ359ꢃꢄlꢅ

N7001PRV5 5/04 Rev A

Download from Www.Somanuals.com. All Manuals Search And Download.

Grizzly Saw G9744Z2 User Manual
Haier Flat Panel Television HL15E User Manual
Haier Washer Dryer HWDC1000TXVE User Manual
Harbor Freight Tools Log Splitter 40318 User Manual
Harbor Freight Tools Power Hammer 93364 User Manual
Harman Kardon Home Theater System HK3380 User Manual
HP Hewlett Packard Network Card PCI 9111DG HR User Manual
HP Hewlett Packard Network Router 2040D User Manual
IBM Computer Monitor 07N2250 User Manual
iLive MP3 Docking Station IC2807BLK User Manual