Models:
6000TRI-IPI
6000TRI-SP
Installers Guide
Underwriters
Laboratories Listed
READ THIS MANUAL BEFORE INSTALLING OR
OPERATING THISAPPLIANCE. THIS INSTALLERS
GUIDE MUST BE LEFT WITH APPLIANCE FOR
FUTURE REFERENCE.
WARNING: IF THE INFORMATION
IN THESE INSTRUCTIONS IS NOT
FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUS-
ING PROPERTY DAMAGE, PER-
SONAL INJURY, OR DEATH.
WARNING: IMPROPER INSTALLA-
TION, ADJUSTMENT, ALTERATION,
SERVICE OR MAINTENANCE CAN
CAUSE INJURY OR PROPERTY DAM-
AGE. REFER TO THIS MANUAL. FOR
ASSISTANCE OR ADDITIONAL INFOR-
MATION CONSULT A QUALIFIED IN-
STALLER, SERVICE AGENCY, OR THE
GAS SUPPLIER.
- Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
- What to do if you smell gas
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
1. This appliance may be installed in an af-
termarket, permanently located, manufac-
tured (mobile) home, where not prohibited
by local codes.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
the fire department.
2. This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.
- Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.
Printed in U.S.A. Copyright 2005,
Please contact your Heat & Glo dealer with any
questions or concerns. For the number of your nearest
Heat & Glo dealer, please call 1-888-427-3973.
Heat & Glo, a brand of Hearth & HomeTechnologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;
4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)
543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Safety and Warning Information ................................................ 2
Service Parts Lists ..................................................................... 4
Î
Section 1: Approvals and Codes ............................................... 8
Appliance Certification................................................................... 8
Installation Codes.......................................................................... 8
HighAltitude Installations ............................................................... 8
Section 2: Getting Started ......................................................... 9
Introducing the Heat & Glo Gas Fireplaces ................................... 9
Pre-installation Preparation ........................................................... 9
Section 3: Installing the Fireplace ...........................................11
Constructing the Fireplace Chase ...............................................11
Step 1
Step 2
Step 3
Locating the Fireplace ..................................................11
Framing the Fireplace.................................................. 12
Installing the Vent System............................................ 14
A. Vent System Approvals........................................... 14
B. Installing Vent Components.................................... 21
C. Vent Termination .................................................... 24
Positioning, Leveling, and
Î
Step 4
Securing the Fireplace................................................. 26
Installing the Optional Heat-Zone Kit............................ 27
The Gas Control Systems ........................................... 27
The Gas Supply Line ................................................... 28
Gas Pressure Requirements ...................................... 28
Wiring the Fireplace .................................................... 30
Step 5
Step 6
Step 7
Step 8
Step 9
Step 10 Finishing ...................................................................... 31
Step 11 Installing Trim, Logs, and Ember Material.................... 32
Installing the Trim......................................................... 32
Positioning the Logs .................................................... 32
Shutter Settings ........................................................... 32
Placing the Ember Material.......................................... 32
Glass Specifications .................................................... 32
Step 12 Before Lighting the Fireplace ....................................... 33
Step 13 Lighting the Fireplace .................................................. 34
After the Installation ..................................................................... 34
Section 4: Maintaining and Servicing Your Fireplace......... 34
Î = Contains updated information.
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
3
Download from Www.Somanuals.com. All Manuals Search And Download.
6000TRI-IPI, 6000TRI-SP
(NG, LP) Exploded Parts Diagram
(GN, PL) Vue éclatée des pièces
Service Parts
Beginning Manufacturing Date: 4-2001
Ending Manufacturing Date: ________
14
15
1
2
17
18
13
4
16
5
3
6 Log set assembly
7
12
8
11
10
9
Part number list on following page.
La liste des numéros de pièce se
trouve à la page suivante.
*
*
4
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Parts List / Liste des pièces de rechange
6000TRI-SP, 6000TRI-IPI
IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When order-
ing, supply serial and model numbers to ensure correct service parts. / IMPORTANT : L'information fournie dans cette brochure
n'est valide que pendant une courte période. Les sites VIP des distributeurs disposent des renseignements les plus récents.
Lors d'une commande, veuillez fournir les numéros de série et de modèles pour un remplacement adéquat des pièces.
ITEM /
PIÈCE
SERIAL #
/N° DE SÉRIE
PART NUMBER
/ N° DE PIÈCE
COMMON PARTS / PIÈCES COMMUNES
PRE 002324002
POST 002324002
385-130
1
2
Surround / Entourent
Hood / Hotte
2026-108
SRV60-143-BK
3
Glass Door Assembly / Porte en verre
Burner NG, LP / Brûleur GN, PL
Log Grate / Grille de Bûche
TRI Log Set Assembly / TRI Jeu de Bûches
Log 1 / Bûche 1
GLA-6TROC
PRE 002324002 385-339A
POST 002324002 SRV2026-007A
4
5
385-360A
6
LOGS-6TRIC
SRV2026-071
SRV385-738
SRV385-739
SRV385-737
SRV385-736
SRV385-740
BRICK-6000-FB
SRV2027-372
SRV2027-371
SRV2027-370
7
8
Log 2 / Bûche 2
9
Log 3 / Bûche 3
10
11
12
Log 4 / Bûche 4
Log 5 / Bûche 5
Log 6 / Bûche 6
Wall Refractory Kit
13
14
15
Wall Refractory Kit - Right Wall
Wall Refractory Kit - Left Wall
Wall Refractory Kit - Back Wall
16
Insulation Board / Conseil d'Isolation
385-401
Flue Restrictor / Restricteur de conduite de cheminée
Vent Gasket / Joint de Conduit
385-128
2026-114
Í
INTERMITTENT PILOT IGNITION (IPI)* / IPI ALLUMAGE SEULEMENT
Junction Box / Boîtier de raccordement
PRE 002324002 383-250A
POST 002324002 4021-013
17
17
NG Conversion - IPI Kit / Module de conversion GN - IPI
LP Conversion - IPI Kit / Module de conversion PL - IPI
STANDING PILOT IGNITION* / ALLUMAGE PAR VEILLEUSE
Junction Box / Boîtier de raccordement
NGK-6TRI-IPI
LPK-6TRI-IPI
4021-013
NGK-6TRI
LPK-6TRI
NG Conversion - IPI Kit / Module de conversion GN - IPI
LP Conversion - IPI Kit / Module de conversion PL - IPI
ACCESSORIES / ACCESSOIRES
Fan Kit / Module de ventilateur
GFK-160A
WSK-21
Wall Switch Kit, Off-white / Interrupteur mural, blanc crème
Wall Switch Kit, White / Interrupteur mural, blanc
Trim Door Mesh / Écran porte de garniture
WSK-21-W
MESH-6000
*Also see pages 6 and 7 for additional IPI and Standing Pilot Ignition service part numbers.
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6000TRI-IPI
Service Parts
(NG, LP) Exploded Parts Diagram
(GN, PL) Vue éclatée des pièces
Beginning Manufacturing Date: 7-03
Ending Manufacturing Date: ______
6
Intermittent Pilot Ignition
ValveAssembly
17
16
4
18
15
7
14
5
13
12
1
11
10
8
2
9
3
ITEM /
PIÈCE
SERIAL #
/N°DE SÉRIE
PART NUMBER
/ N° DE PIÈCE
DESCRIPTION
PRE 002324002
POST 002324002
N/A
1
2
3
Control Panel / Tableau de commande avant
2026-103
060-521A
ON/OFF Rocker Switch / Interrupteur à bascule MARCHE/ARRÊT
Flame Control Knob / Flamber le Bouton de Contrôle
PRE 002324002
POST 002324002
N/A
571-531
PRE 002324002
385-510A
4
4
5
Pilot Assembly NG / Module de veilleuse GN
Pilot Assembly LP / Module de veilleuse PL
Valve Bracket / Parenthèse de Valve
POST 002324002
4021-025
PRE 002324002
POST 002324002
PRE 002324002
POST 002324002
385-511A
4021-026
550-169
2025-101
6
7
8
Ground Strap / Courroie de Raison(Terre)
Flex Ball Valve Assembly / Fléchir l'Assemblée de Soupape de Balle
Valve NG / Valve GN
2025-512
302-320A
750-500
8
Valve LP / Valve PL
750-501
9
Flexible Gas Connector / Tuyau à gaz flexible
Module / Module
Wire Assembly / Module de fil
Manifold Assembly / L'Assemblée diverse
Manifold Gasket /Joint Diversifié(Varié)
Valve Plate Gasket / Joint de Plat de Valve
Orifice Assembly NG (#43C) / Assemblée d'Orifice GN (#43C)
Orifice Assembly LP (#54C) / Assemblée d'Orifice PL (#54C)
Orifice Assembly NG (#53C) / Assemblée d'Orifice GN (#53C)
Orifice Assembly LP (#66C) / Assemblée d'Orifice PL (#66C)
Pilot Bracket / Parenthèse Pilote
Shutter Assembly / Assemblée d'Obturateur
Battery Pack / Paquet de Batterie(Pile)
3 Volt Transformer / 3 Transformateur de Volt
477-301A
593-592
593-590A
385-301A
385-410
10
11
12
13
14
15
15
16
16
17
18
385-402
582-843A
582-854A
582-853A
582-866A
385-164
319-316A
593-594A
593-593A
6
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
6000TRI-SP
Service Parts
(NG, LP) Exploded Parts Diagram
(GN, PL) Vue éclatée des pièces
Beginning Manufacturing Date: 7-03
Ending Manufacturing Date: ______
4
Standing Pilot Ignition
ValveAssembly
17
16
12
15
6
13
14
9
7
5
11
18
2
8
1
3
10
ITEM /
PIÈCE
SERIAL #
/N°DE SÉRIE
PART NUMBER
/ N° DE PIÈCE
DESCRIPTION
1
2
Control Panel / Tableau de commande avant
385-154
ON/OFF Rocker Switch / Interrupteur à bascule MARCHE/ARRÊT
Flame Control Knob / Flamber le Bouton de Contrôle
Pilot Assembly NG / Module de veilleuse GN
Pilot Assembly LP / Module de veilleuse PL
Valve Bracket / Parenthèse de Valve
060-521A
571-531
3
4
485-510A
485-511A
550-169
4
5
6
Shutter Assembly / Assemblée d'Obturateur
Flex Ball Valve Assembly / Fléchir l'Assemblée de Soupape de Balle
Valve NG / Valve GN
319-316A
302-320A
060-522
7
8
8
Valve LP / Valve PL
060-523
9
Flexible Gas Connector / Tuyau à gaz flexible
Pilot Control Knob / Piloter le Bouton de Contrôle
Wire Assembly / Module de fil
477-301A
571-530
10
11
12
13
14
15
15
16
16
17
18
049-552A
385-301A
385-410
Manifold Assembly / L'Assemblée diverse
Manifold Gasket /Joint Diversifié(Varié)
Valve Plate Gasket / Joint de Plat de Valve
Orifice Assembly NG (#43C) / Assemblée d'Orifice GN (#43C)
Orifice Assembly LP (#54C) / Assemblée d'Orifice PL (#54C)
Orifice Assembly NG (#53C) / Assemblée d'Orifice GN (#53C)
Orifice Assembly LP (#66C) / Assemblée d'Orifice PL (#66C)
Pilot Bracket / Parenthèse Pilote
385-402
582-843A
582-854A
582-853A
582-866A
385-164
Piezo Ignitor / Allumeur piézo
291-513
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Approvals and
Codes
1
High Altitude Installations
Appliance Certification
U.L. Listed gas appliances are tested and approved without
requiring changes for elevations from 0 to 2,000 feet in the
U. S. A. and in Canada.
The Heat & Glo fireplace models discussed in this Installers
Guide have been tested to certification standards and listed
by the applicable laboratories.
When installing this appliance at an elevation above 2,000
feet, it may be necessary to decrease the input rating by
changing the existing burner orifice to a smaller size. Input
rate should be reduced by 4% for each 1000 feet above a
2000 foot elevation in the U.S.A. or 10% for elevations
between 2000 and 4500 feet in Canada. If the heating value
of the gas has been reduced, these rules do not apply. To
identify the proper orifice size, check with the local gas
utility.
Certification
MODELS: 6000TRI-IPI, 6000TRI-SP
LABORATORY: Underwriters Laboratories
TYPE: Direct Vent Gas Fireplace Heater
STANDARD: ANSIZ21.88-2000•CSA2.33-M98•UL307B
Installation Codes
If installing this appliance at an elevation above 4,500 feet
(in Canada), check with local authorities.
The fireplace installation must conform to local codes. Before
installing the fireplace, consult the local building code
agency to ensure that you are in compliance with all
applicable codes, including permits and inspections.
In the absence of local codes, the fireplace installation must
conform to the National Fuel Gas Code ANSI Z223.1 (in
the United States) or the CAN/CGA-B149 Installation Codes
(in Canada). The appliance must be electrically grounded
in accordance with local codes or, in the absence of local
codes with the National Electric Code ANSI/NFPA No. 70
(in the United States), or to the CSAC22.1 Canadian Electric
Code (in Canada).
These models may be installed in a bedroom or bed-sitting
room in the U.S.A. and Canada.
Heat & Glo Quality Systems
registered by SGS ICS
8
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
2
The Heat & Glo Warranty will be voided by, and Heat & Glo
disclaims any responsibility for, the following actions:
Introducing the Heat & Glo Gas Fireplaces
Heat & Glo direct vent gas fireplaces are designed to oper-
ate with all combustion air siphoned from outside of the
building and all exhaust gases expelled to the outside.
•
Installation of any damaged fireplace or vent system
component.
•
•
•
•
Modification of the fireplace or direct vent system.
Installation other than as instructed by Heat & Glo.
Improper positioning of the gas logs or the glass door.
The information contained in this Installers Guide, unless
noted otherwise, applies to all models and gas control
systems. Gas fireplace diagrams, including the dimensions,
are shown in this section.
Installation and/or use of any component part not manu-
factured and approved by Heat & Glo, not withstanding
any independent testing laboratory or other party approval
of such component part or accessory.
Pre-install Preparation
This gas fireplace and its components are tested and safe
when installed in accordance with this Installers Guide.
Report to your dealer any parts damaged in shipment,
particularly the condition of the glass. Do not install any
unit with damaged, incomplete, or substitute parts.
ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE
HAZARD.
When planning a fireplace installation, it’s necessary to
determine:
The vent system components and trim doors are shipped
in separate packages. The gas logs may be packaged
separately and must be field installed.
• Where the unit is to be installed.
• The vent system configuration to be used.
• Gas supply piping.
Read all of the instructions before starting the
installation. Follow these instructions carefully during
the installation to ensure maximum safety and benefit.
Failure to follow these instructions will void the
owner’s warranty and may present a fire hazard.
• Electrical wiring.
• Framing and finishing details.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
If the fireplace is to be installed on carpeting or tile, or on
any combustible material other than wood flooring, the
fireplace should be installed on a metal or wood panel that
extends the full width and depth of the fireplace.
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
9
28 1/2 [724mm]
14 1/4
[362mm]
21 1/2 [548mm]
8 [203mm]
VENT COLLARS
11 5/8 [297mm]
ELECTRICAL
ACCESS
8 [203mm]
VENT
COLLARS
GAS LINE
ACCESS
34 5/8
[879mm]
38
[965mm]
25 1/4
[642mm]
26 7/8
[682mm]
2 1/8
[55mm]
3 1/2
[90mm]
36 1/8
[916mm]
12 3/4
[323mm]
41 1/8
6 7/8 [174mm]
[1044mm]
TOP STANDOFFS
TOP VENT COLLARS
REAR VENT COLLARS
HOOD
TRIM
DOOR
RATING PLATE
AND LABELS
GAS
LINE
ACCESS
ELECTRICAL
ACCESS
GAS
CONTROLS
Figure 1. Diagram of the 6000TRI-IPI, 6000TRI-SP
10
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
1” MIN. (25mm)
B
A
Installing the Fireplace
3
Constructing the Fireplace Chase
A chase is a vertical box-like structure built to enclose the
gas fireplace and/or its vent system. Vertical vents that run
on the outside of a building may be, but are not required to
be, installed inside a chase.
D
E
C
CAUTION: TREATMENT OF FIRESTOP SPACERS AND
CONSTRUCTION OF THE CHASE MAY VARY WITH THE
TYPE OF BUILDING. THESE INSTRUCTIONS ARE NOT
SUBSTITUTES FOR THE REQUIREMENTS OF LOCAL
BUILDING CODES. THEREFORE, YOUR LOCAL BUILD-
ING CODES MUST BE CHECKED TO DETERMINE THE
REQUIREMENTS FOR THESE STEPS.
1/2” MIN. (13mm)
A
42”
Note* 42”
B
22”
22”
C
36”
40”
D
51”
57”
E
72”
80”
*If venting with (2) 900 elbows off rear of unit
the dimensions C, D, and E, will change.
Figure 2. Fireplace Dimensions, Locations,
and Space Requirements
Factory-built fireplace chases should be constructed in the
manner of all outside walls of the home to prevent cold air
drafting problems. The chase should not break the outside
building envelope in any manner.
Minimum Clearances
from the Fireplace to Combustible Materials
Inches
mm
This means that the walls, ceiling, base plate and cantile-
ver floor of the chase should be insulated. Vapor and air
infiltration barriers should be installed in the chase as per
regional codes for the rest of the home.Additionally, Heat &
Glo recommends that the inside surfaces be sheetrocked
and taped for maximum air tightness.
Glass Front........................ 36 .................... 914
Floor ................................... 0 ....................... 0
Rear ...................................1/2 ..................... 13
Sides .................................1/2 ..................... 13
Surround Sides*.................. 0 ....................... 0
Top ................................... 3 1/2 ................... 89
Ceiling** ............................. 31 .................... 787
To further prevent drafts, the firestops should be caulked to
seal gaps. Gas line holes and other openings should be
caulked or stuffed with insulation. If the unit is being in-
stalled on a cement slab, we recommend that a layer of
plywood be placed underneath to prevent conducting cold
up into the room. Be sure to include spark arrestors for
woodburning units if they are required.
* See Figure 3.
** The clearance to the ceiling is measured from the top
of the unit, excluding the standoffs (see Figure 39).
The distance from the unit to combustible construction
is to be measured from the unit outer wrap surface to
the combustible construction, NOT from the screw heads
that secure the unit together.
THE CHASE SHOULD BE CONSTRUCTED SO THATALL
CLEARANCES TO THE FIREPLACE ARE MAINTAINED
AS SPECIFIED WITHIN THIS INSTALLERS GUIDE.
Minimum Clearances
from the Vent Pipe to Combustible Materials
Step 1.
Locating the Fireplace
Inches
mm
Vertical Sections. ............. 1 ................ 25
The following diagram shows space and clearance require-
ments for locating a fireplace within a room.
Horizontal Sections
Top ..................................... 3 ................ 75
Bottom ............................... 1 ................ 25
Sides ................................. 1 ................ 25
Clearance Requirements
The top, back, and sides of the fireplace are defined by
stand-offs. The minimum clearance to a perpendicular wall
extending past the face of the fireplace is one inch (25 mm).
The back of the fireplace may be recessed 21 1/2 inches
(546 mm) into combustible construction.
At Wall Firestops
Top ..................................... 3 ................ 75
Bottom ............................... 1 ................ 25
Sides ................................. 1 ................ 25
For minimum clearances, see the direct vent termination
clearance diagrams on pages 24 and 25 in this manual.
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Step 2. Framing the Fireplace
Fireplace framing can be built before or after the fireplace is
set in place. Framing should be positioned to accommo-
date wall coverings and fireplace facing material. The dia-
gram below shows framing reference dimensions.
CAUTION: MEASURE FIREPLACE DIMENSIONS AND
VERIFY FRAMING METHODS AND WALL COVERING
DETAILS BEFORE FRAMING.
Framing should be
constructed of 2 X 4
lumber or heavier.
Noncombustible zone is defined
by 3” above the elbow for the
entire width and depth (behind
the front header) of the firebox.
WALL
STUD
3”
B
C
A
3 1/2”
A. ............. 42”*
B. .........38 1/2”
C. ............... 22”
D. .........42 3/4”
E. .........27 7/8”
1/2” CLEARANCE FROM BACK OF FIREPLACE TO COMBUSTIBLE
1/2” CLEARANCE
FROM BOTH SIDES
OF FIREPLACE
TO COMBUSTIBLE
E
D
FRAMING
MEMBER
Shows center of 10” x 12” vent framing
holes for top and rear venting. The center
of the hole is one (1) inch (25.4mm) above
the center of the horizontal vent pipe.
0” CLEARANCE TO
FRAMING MEMBER
0” CLEARANCE
Figure 3. Framing Dimensions
12
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
4
6
12
DVP4
DVP6
DVP12
14-1/4
12-3/16
MAX.
2
MIN.
24
36
DVP12A
48
9-7/8
DVP24
45.0O
10-1/4
DVP45
DVP36
11-1/4
7-1/4
1-1/4 TYP
DVP48
1/2 TYP
8-9/16
12-9/16
DVP
90ST
NOTE: PIPES OVERLAP 1-1/4 INCHESAT EACH JOINT.
Figure 4. DVP-Series Direct Vent Component Specifications (5-inch inner pipe / 8-inch outer pipe)
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3. Installing the Vent System
A. Vent System Approvals
Identifying Vent Components
The vent systems installed on this gas fireplace may in-
clude one, two, or three 90° elbow assemblies. The rela-
tionships of vertical rise to horizontal run in vent configura-
tions using 90° elbows MUST BE strictly adhered to. The
rise to run relationships are shown in the venting drawings
and tables. Refer to the diagrams on the next several pages.
These models are approved to use DVP-series direct vent
pipe components and terminations (see Figures 4 and 5).
Approved vent system components are labeled for identifi-
cation. This pipe is tested and listed as an approved com-
ponent of the fireplace. The pipe is tested to be run inside
an enclosed wall. There is no requirement for inspection
openings at each joint within the wall. There is no required
pitch for horizontal vent runs. NO OTHER VENTING SYS-
TEMS OR COMPONENTS MAY BE USED.
NOTE: Two 45° elbows may be used in place of one
90° elbow. Rise to run ratios in the vent system must
be followed if 45° elbows are used.
Detailed installation instructions are included with each vent
termination kit and should be used in conjunction with this
Installers Guide.
This model has vent starting collars on both the top and the
back of the unit. Depending upon the installation, decide
which ONE set of starting collars will be used to attach the
vent system. The starting collar sealing cap must remain
on the starting collar NOT used.
The flame and ember appearance may vary based on the type
of fuel burned and the venting configuration used.
STORM COLLAR
ROOF FLASHING
VERTICAL
TERMINATION
HORIZONTAL
TERMINATION
PIPE LENGTH
Terminations Kits
WALL FIRESTOP
90 DEGREE
ELBOW
PVK-80
(For use on IPI units only)
CEILING
FIRESTOP
DVP-TRAP
SERIES
DVP-TB1
(Required to have a minimum of 3
feet of vertical in the vent system)
DVP-TVHW
Figure 5. Vent System Components and Termination Kits
14
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Flue Restrictor Instructions
1. Remove Exhaust Shield using a 1/4” nut driver by
removing the four screws securing it in place (see
Figure 7).
STRAIGHT UP
VERTICAL VENTING
V (FT.)
40' MAX. (12.4 M)
EXHAUST
SHIELD
NOTE: On vertical venting
configurations over 10 feet
install the flue restrictor
(385-128) included in the
manual bag assembly. See
flue restrictor instructions.
FLUE
RESTRICTOR
Figure 7
2. Break the Flue Restrictor into two pieces. Do this
by bending the part back and forth until it breaks
(see Figure 8).
Figure 6.
Straight Up Vertical Venting
BREAK
HERE
Figure 8. Flue Restrictor
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
15
3. Match the amount of vertical you have in the sys-
tem with the chart to find the appropriate position
to set the Flue Restrictor (see Figure 9).
HORIZONTALVENTING
Kit No.
H Max. Run
DVP-TRAP
24" (610 mm)
- CHART -
Top Vent
NG
Top Vent
LP
Rear Vent
NG
Rear Vent
LP
Vertical
No
No
No
4'
1-1
2-2
3-3
3-4
3-4
4-4
4-4
5-4
Restrictor
Restrictor
Restrictor
No
Restrictor
8'
15'
1-2
3-2
3-3
3-3
3-4
3-4
4-4
1-1
2-2
3-3
3-3
3-4
3-4
4-4
1-2
2-3
2-3
3-3
3-3
3-4
20'
25'
30'
H
35'
90-DEGREE
ELBOWS
40'
45-DEGREE
ELBOW
Figure 9
4. Center the Flue Restrictor on vent and secure in
place by using two self-tapping screws.
5. Reinstall the Exhaust Shield.
1
2
3
4
5
NOTE: This model is tested and approved to use
45° elbows in corner installations. However, 90°
elbows will result in better performance. The
use of two 900 elbows in a corner installation
will affect space requirements (see Figure 2).
SETTINGS
Figure 11. Corner Installation
1
2
3
4
5
Figure 10
16
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING WITH ONE (1) 90° ELBOW
V
H
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
2' MAX. (610mm)
4' MAX. (1.22m)
6' MAX. (1.86m)
8' MAX. (2.4m)
V+H=40' MAX. (12.4m)
H = 8' MAX. (2.4m)
NOTE: On vertical venting configurations where
the vertical component is over 10 feet, install
the flue restrictor included in the manual bag
assembly to improve flame appearance.
V
H
Figure 12. Venting with One 90° Elbow
VENTING WITH ONE (1) 90° ELBOW
V (FT.)
H (FT.)
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
5' MAX. (1.52m)
10' MAX. (3.1m)
15' MAX. (4.65m)
20' MAX. (6.2m)
H
V
V+H= 40’ MAX. (12.4MM) H = 20' MAX. (6.2m)
H
V
NOTE: For corner installations:A6-inch (152mm)
section of straight pipe may need to be attached to
the fireplace before a 90o elbow, to allow the vent
pipe to clear the top standoffs.
NOTE: If a 90o elbow is first attached to the unit,
the maximum horizontal run is 3-feet (914mm).
Figure 13. Venting with One 90° Elbow
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
17
VENTING WITH TWO (2)
90° ELBOWS
H
1
V
H
V
H
H + H1
1´ MIN. (305 mm)
2´ MIN. (610 mm)
3´ MIN. (914 mm)
4´ MIN. (1.22 m)
2´ MAX. (610 mm)
4´ MAX. (1.22 m)
6´ MAX. (1.86 m)
8´ MAX. (2.48 m)
5´ MAX. (1.52m)
10´ MAX. (3.1m)
15´ MAX. (4.65m)
20´ MAX. (6.2m)
V+H+H1 = 40´ MAX. (12.4 m) H = 8´ MAX. (2.48 m) H+H1 = 20´ MAX. (6.2m)
Figure 14. Venting with Two 90° Elbows
VENTING WITH TWO (2) 90o ELBOWS
V FT.
H + H1 (FT.)
5´ MAX. (1.52m)
10´ MAX. (3.1m)
15´ MAX. (4.65m)
20´ MAX. (6.2m)
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
V+H+H1= 40' MAX.(12.4m) H+H1 = 20´ MAX. (6.2m)
V+V1+H= 40' MAX.(12.4m)
V
1
V
H
H
1
V
H
Figure 15. Venting with Two 90° Elbows
18
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING WITH THREE (3) 90° ELBOWS
V
H
H + H1
1´MIN. (305mm)
2´MIN. (610mm)
3´MIN. (914mm)
4´MIN. (1.22m)
2´MAX. (610mm)
4´MAX. (1.22m)
6´MAX. (1.86m)
8´MAX. (2.48m)
5´MAX. (1.52m)
10´MAX. (3.1m)
15´MAX. (4.65m)
20´MAX. (6.2m)
V1+V+H+H1 = 40´ MAX.(12.4 m) H = 8´MAX.(2.48 m) H+H1 = 20´MAX.(6.2 m)
V
1
V
H
1
H
V
H
H + H1 + H2
1´MIN. (305mm)
2´MIN. (610mm)
3´MIN. (914mm)
4´MIN. (1.22m)
2´MAX. (610mm)
4´MAX. (1.22m)
6´MAX. (1.86m)
8´MAX. (2.48m)
5´MAX. (1.52m)
10´MAX. (3.1m)
15´MAX. (4.65m)
20´MAX. (6.2m)
1
2
V+H+H +H = 40´ MAX. (12.4 m)
H = 8´ MAX. (2.48 m)
H+H1+H2 = 20´ MAX. (6.2 m)
V
H
2
H
1
H
Figure 16. Venting with three 90° elbows
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
19
VENTING WITH THREE (3) 90° ELBOWS
V (FT.)
H (FT.)
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
5' MAX. (1.52m)
10' MAX. (3.1m)
15' MAX. (4.65m)
20' MAX. (6.2m)
NOTE: H + H1 = 20' MAX. (6.2m)
V + V1 + H + H1= 40' MAX. (12.4m)
H
1
V
1
V
H
V
1
H
1
V
H
V + V1 (FT.)
H + H1 (FT.)
5' MAX. (1.52m)
10' MAX. (3.1m)
15' MAX. (4.65m)
20' MAX. (6.2m)
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
H +H1 = 20' MAX. (6.2m)
NOTE: V+V1+H +H1 = 40' MAX. (12.4m)
Figure 17. Venting with three 90° elbows
20
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Attach the First Vent Component to the
Starting Collars
B. Installing Vent Components
After determining which set of starting collars will be used
(top or rear), follow venting instructions accordingly.
To attach the first vent component to the starting collars of
the fireplace:
Venting Out the Rear Vent
• Make sure that the fiberglass gasket supplied in the
manual bag seals between the first 8 inch (203mm)
vent component and the outer fireplace wrap. Using 2
self-tapping screws from the manual bag secure that
gasket to the outer wrap (see Figure 19).
Remove the installed rear seal cap from the rear starting
collars by cutting the strap at each end. (see Figure 18).
Follow the vent configuration tables accordingly.
Remove the insulation from the REAR five inch flue, pull
the heat shield out from outside of the firebox.
WARNING: THE TOP HEAT SHIELD (INSIDE
THE FIREBOX) MUST REMAIN ATTACHED IF
THE VENT SYSTEM IS ATTACHED TO THE
REAR STARTING COLLARS. SEE FIGURE 18.
!
OUTER
WRAP
FIRST VENT
COMPONENT
FIBERGLASS
GASKET
Venting Out the Top Vent
Remove the two screws in the top vent collar seal cap and
remove the top vent collar seal cap and two pieces of in-
sulation inside the top two starting collars (See Figure 18).
Remove the heat shield from inside the TOP five inch flue
from outside of the firebox.
The glass must be taken off again for positioning the logs
when the unit is finally installed in place and finished around
it. Re-install the glass door. Attach vent system to the top
starting collars.
Figure 19. Fiberglass Gasket
WARNING: THE REAR VENT COLLAR SEAL
CAP MUST REMAIN ATTACHED TO THE REAR
VENT COLLARS IF THE VENT SYSTEM ISATTACHED
TO THE TOP STARTING COLLARS.
DVP PIPE:
!
1. Attaching the Venting to the Fireplace
Refer to Cinch Pipe and Termination Cap installation in-
structions.
WARNING: FAILURE TO REMOVE INSULATION
IN THE SET OF COLLARS YOU ARE USING
COULD NEGATIVELY AFFECT FIREPLACE
PERFORMANCE.
2. Assembling Vent Sections
!
Refer to Cinch Pipe and Termination Cap installation in-
structions.
WARNING: YOU MUST LEAVE THE INSULA-
TION IN PLACE IN THE SET OF COLLARS YOU
!
ARE NOT USING. FAILURE TO DO THIS COULD
CAUSE A FIRE.
Venting Out Top
Venting Out Rear
SEAL
CAP
SEAL
CAP
HEAT
SHIELD
INSULATION
DISCARD BOTH
PIECES and
HEAT SHIELD
HEAT
SHIELD
DISCARD
INSULATION
and
HEAT SHIELD
CUT
HERE
Cut the seal cap
strap and remove white
gasket material.
Figure 18
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
21
• If the combustible materials are not in place at the time
of install the elbow heat shield may be screwed to the
exhaust pipe (see Figure 22). Cut the tabs as shown
and bend down. Secure the heat shield to the pipe main-
taining 3” to 4” between the pipe and shield.
WARNING: ENSURE THAT THE FIBERGLASS
GASKET SUPPLIED WITH THE FIREPLACE
SEALS BETWEEN THE FIRST VENT COMPONENT
AND THE OUTER FIREPLACE WRAP.
!
If the installation is for a termination cap attached directly
to the fireplace, skip to the sections, Install Firestops and
Vent Termination.
SCREW
3. Continue Adding Vent Components
3”
(76mm)
WARNING: INSTALLATION OF THIS FIRE-
!
PLACE REQUIRES THE USE OF HEAT
SHIELD 570-290 ABOVE THE FIRST 900 ELBOW IN
THE VENTING SYSTEM.
To Install the Heat Shield:
1. Determine if the heat shield is required. Do so by mea-
suring the vertical distance between the top horizontal
surface of the elbow to any combustible surface above.
If the distance is more than 4 inches, the heat shield is
NOT required. If it is 4 inches or less, the heat shield IS
REQUIRED. Install per the following steps. See Figure 20.
Figure 22
• Refer to Cinch Pipe and Termination Cap installation in-
structions.
COMBUSTIBLE
SURFACE
• Continue adding vent components, locking each succeed-
ing component into place.
• Ensure that each succeeding vent component is secure-
ly fitted and locked into the preceding component in the
vent system.
3” MIN.
(76mm)
HEAT
SHIELD
• 90° elbows may be installed and rotated to any point
around the preceding component’s vertical axis. If an el-
bow does not end up in a locked position with the pre-
ceding component, attach with a minimum of two (2)
sheet metal screws.
4. Install Support Brackets
Refer to Cinch Pipe and Termination Cap installation in-
structions.
Figure 20
2. Fasten the shield in place using the four pilot holes pro-
vided in the part. The shield should be oriented such that
the 13 1/8 inch dimension (longest dimension) is run-
ning in the same direction the elbow is pointing. The
shield should be centered directly above the elbow, and
positioned so that it creates a 1/2 inch airspace between
the shield and the combustible surface. See Figure 21.
CORRECT
INCORRECT
COMBUSTIBLE SURFACE
DIRECTION
UP
HEAT SHIELD
900ELBOW
Figure 21
22
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Install Firestops
For Vertical Runs - One ceiling firestop is REQUIRED at
the hole in each ceiling through which the vent passes.
For Horizontal Runs - Firestops are REQUIRED on both
sides of a combustible wall through which the vent passes.
To install firestops for vertical runs that pass through ceilings:
NOTE: Model DVP-TRAP does not need an exterior
firestop on an exterior combustible wall.
• Position a plumb bob directly over the center of the verti-
cal vent component.
To install firestops for horizontal runs that pass through
either interior or exterior walls:
• Mark the ceiling to establish the centerpoint of the vent.
• Drill a hole or drive a nail through this centerpoint.
• Cut a 10-inch by 12-inch (254mm x 305mm) hole through
the wall.
• Check the floor above for any obstructions, such as wir-
ing or plumbing runs.
NOTE: The center of the hole is one (1) inch (25.4mm)
above the center of the horizontal vent pipe.
• Reposition the fireplace and vent system, if necessary,
to accommodate the ceiling joists and/or obstructions.
• Position the firestops on both sides of the hole previ-
ously cut and secure the firestops with nails or screws.
• Cut an 10-inch X 10-inch (254mm X 254mm) hole through
the ceiling, using the centerpoint previously marked.
• The heat shields of the firestops MUST BE placed to-
wards the top of the hole.
• Frame the hole with framing lumber the same size as the
ceiling joists.
• Continue the vent run through the firestops.
NOTE: There must be NO INSULATION or other
combustibles inside the framed firestop opening.
10" (254mm)
10" (254mm)
CHIMNEY
HOLE
10"
INTERIOR
WALL SHIELD
EXISTING CEILING
JOISTS
NEW
FRAMING
MEMBERS
CEILING
12"
Figure 25. 10" x 10" Hole & New Framing Members
Figure 23. 10" x 12" Hole and Vent Pipe
HEAT SHIELD
TRIM HEAT
SHIELD IF TOO
LONG, ADD TO
SHIELD IF TOO
SHORT
EXTERIOR
FIRESTOP
INTERIOR
FIRESTOP
Figure 24. Heat Shield, Interior & Exterior Firestops
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
23
If the area above the ceiling is NOT an attic, position and
secure the ceiling firestop on the ceiling side of the previously
cut and framed hole.
C. Vent Termination
Refer to Cinch Pipe and Termination Cap installation in-
structions.
WARNING: THE TERMINATION CAP MUST BE
POSITIONED SO THAT THEARROW IS POINT-
ING UP.
NOTE: There must be NO INSULATION or other
combustibles inside the framed firestop opening.
!
WARNING: VENTING TERMINALS SHALL
NOT BE RECESSED INTO A WALL OR SID-
!
ING. VENT TERMINATION CLEARANCES MUST
BE FOLLOWED TO AVOID FIRE DANGER. SEE
VENT TERMINATION MINIMUM CLEARANCES DI-
AGRAM ON FOLLOWING PAGE.
JOIST
CEILING
NAILS (4 REQUIRED)
CEILING FIRESTOP
Figure 26. Ceiling Firestop (Ceiling Side)
If the area above the ceiling IS an attic, position and secure
the firestop on top of the previously framed hole.
NOTE: Keep insulation away from the vent pipe at least
1 inch (25mm).
7 1/4”
(184mm)
NAILS (4 REQUIRED)
Figure 28. Trapezoid Termination Cap
RAFTER
CEILING
CEILING FIRESTOP
Figure 27. Attic Firestop
24
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
M
N
P
R
G
v
A
H
D
Q
(See Note 2)
E
v
V
B
L
U.S.
(3 FT)
B
T
v
v
v
B
v
S
S
Electrical
Service
V
V
F
v
M
I
D*
V
v
X
A
J or K
X
= VENT TERMINAL
=AIR SUPPLY INLET
= AREA WHERE TERMINAL IS NOT PERMITTED
V
A
B
= 12" ....................... clearances above grade, veran-
K
= 3 ft. (U.S.A.)
(See Note 1)
da, porch, deck or balcony
6 ft. (Canada) ......... clearance to a mechanical
air supply inlet
= 12" ....................... clearances to window or door
that may be opened, or to per-
L** = 7 ft. ......................... clearance above paved
(See Note 1)
sidewalk or a paved driveway
located on public property
manently closed window.
D*
= 18" ....................... vertical clearance to unventilat-
ed soffit or to ventilated soffit lo-
M*** = 18" ......................... clearance under veranda,
porch, deck, balcony or over-
hang
cated above the terminal
*30” ...................... for vinyl clad soffits and below
electrical service
42” ......................... vinyl
N
P
= 6” ........................... non-vinyl sidewalls
12” ......................... vinyl sidewalls
F
=
9" ........................ clearance to outside corner
G
H
= 6" ......................... clearance to inside corner
= 8 ft.
= 3 ft. (Canada) ...... not to be installed above a gas
meter/regulator assembly within
______________________________Q___M_I_N___________________________________
_____1___c__a_p__________________3___f_e_e__t_________________2__x__Q____A_C_T_U_A_L____
______2__c__a_p__s________________6___f_e_e__t_________________1__x__Q____A_C_T_U_A_L____
______3__c__a_p__s_________________9__f_e_e__t_______________2_/_3__x___Q___A_C_T_U_A__L___
4 caps 12 feet 1/2 x Q ACTUAL
RMAX
3 feet (90cm) horizontally from the
center-line of the regulator
I
= 3 ft. (U.S.A.)
6 ft. (Canada) ...... clearance to gas service regu-
lator vent outlet
= 9" (U.S.A.)
QMIN = # termination caps x 3
RMAX = (2 / # termination caps) x QACTUAL
J
12" (Canada) ........ clearance to non-mechanical air
supply inlet to building or the
combustion air inlet to any other
appliance
S = 6" .......................... clearance from sides of elec-
(See Note 5)
trical service
T
= 12" ......................... clearance above electrical
(See Note 5)
service
NOTE 3: Local codes or regulations may require different
clearances.
** a vent shall not terminate directly above a sidewalk or paved
driveway which is located between two single family dwellings
and serves both dwellings.
NOTE 4: Termination caps may be hot. Consider their proximity to
doors or other traffic areas.
*** only permitted if veranda, porch, deck or balcony is fully open on
a minimum of 2 sides beneath the floor, or meets Note 2.
NOTE 5: Location of the vent termination must not interfere with
access to the electrical service.
NOTE 1: On private property where termination is less than 7 feet
above a sidewalk, driveway, deck, porch, veranda or balcony, use of
a listed cap shield is suggested.
WARNING: In the U.S: Vent system termination is NOT permitted
in screened porches. You must follow side wall, overhang and
ground clearances as stated in the instructions.
NOTE 2: Termination in an alcove space (spaces open only on one side
and with an overhang) are permitted with the dimensions specified for
vinyl or non-vinyl siding and soffits. 1. There must be 3 feet minimum
between termination caps. 2. All mechanical air intakes within 10 feet
of a termination cap must be a minimum of 3 feet below the termination
cap. 3. All gravity air intakes within 3 feet of a termination cap must be
a minimum of 1 foot below the termination cap.
In Canada: Vent system termination is NOT permitted in screened
porches. Vent system termination is permitted in porch areas
with two or more sides open. You must follow all side walls,
overhang and ground clearances as stated in the instructions.
Heat & Glo assumes no responsibility for the improper perfor-
mance of the fireplace when the venting system does not meet
these requirements.
Figure 29. Vent Termination Minimum Clearances
Î
CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE
INSTALLED.
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
25
HORIZONTAL
OVERHANG
WARNING: MAJOR U.S. BUILDING CODES
SPECIFY MINIMUM CHIMNEY AND/OR
!
VENT HEIGHTABOVE THE ROOF TOP. THESE MIN-
IMUM HEIGHTS ARE NECESSARY IN THE INTER-
EST OF SAFETY. SEE THE FOLLOWING DIAGRAM
FOR MINIMUM HEIGHTS, PROVIDED THE TERMI-
NATION CAP IS AT LEAST 20 INCHES FROM A
VERTICALWALLAND 2-FEET BELOWAHORIZON-
TAL OVERHANG.
2 FT.
MIN.
20 INCH MIN.
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
TERMINATION
CAP
X
12
NOTE: This also pertains to vertical vent systems in-
stalled on the outside of the building.
ROOF PITCH
IS X/ 12
To seal the roof hole, and to divert rain and snow from the
vent system:
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
• Attach a flashing to the roof using nails, and use a non-
hardening mastic around the edges of the flashing base
where it meets the roof.
Roof Pitch
H (min.) ft.
• Attach a storm collar over the flashing joint to form a
water-tight seal. Place non-hardening mastic around the
joint, between the storm collar and the vertical pipe.
flat to 6/12
6/12 to 7/12
1.0
1.25
over 7/12 to 8/12
over 8/12 to 9/12
1.5
2.0
2.5
3.25
4.0
5.0
6.0
7.0
7.5
8.0
• Slide the termination cap over the end of the vent pipe
and snap into place.
over 9/12 to 10/12
over 10/12 to 11/12
over 11/12 to 12/12
over 12/12 to 14/12
over 14/12 to 16/12
over 16/12 to 18/12
over 18/12 to 20/12
over 20/12 to 21/12
Step 4. Positioning, Leveling, and
Securing the Fireplace
The diagram below shows how to properly position, level,
and secure the fireplace.
Figure 30. Minimum Height from Roof to
Lowest Discharge Opening
For Vertical Terminations - To locate the vent and install
the vent sections:
• Locate and mark the vent centerpoint on the underside
of the roof, and drive a nail through the centerpoint.
• Make the outline of the roof hole around the centerpoint
nail.
NAILING TABS
(BOTH SIDES)
• The size of the roof hole framing dimensions depend on the
pitch of the roof. There MUST BE a 1-inch (25.4mm) clear-
ance from the vertical vent pipe to combustible materials.
• Mark the roof hole accordingly.
• Cover the opening of the installed vent pipes.
• Cut and frame the roof hole.
Figure 31. Proper Positioning,
Leveling and Securing of a Fireplace
• Use framing lumber the same size as the roof rafters
and install the frame securely. Flashing anchored to the
frame must withstand heavy winds.
• Place the fireplace into position.
• Level the fireplace from side to side and front to back.
• Continue to install concentric vent sections up through
the roof hole (for inside vent installations) or up past the
roof line until you reach the appropriate distance above
the roof (for outside terminations).
• Shim the fireplace with non-combustible material, such
as sheet metal, as necessary.
• Secure the fireplace to the framing by nailing or screwing.
26
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5. Installing the Optional Heat-Zone Kit
Step 6. The Gas Control Systems
NOTE: There must be NO INSULATION or other com-
bustibles inside the framed firestop opening.
WARNING: THIS UNIT IS NOT FOR USE WITH
SOLID FUEL.
!
The types of gas control systems used with this model are
Intermittent Pilot Ignition (IPI) and Standing Pilot Ignition (SP).
Intermittent Pilot Ignition (IPI) System
This system includes a 3V control valve, electronic module
and intermittent pilot.
WARNING: CONTINUOUS 110-120 VAC SER-
VICE MUST BE WIRED DIRECTLYTO THE FIRE-
!
HEAT-ZONE
ATTACHES
HERE
PLACE JUNCTION BOX.
FLAME SENSOR
ROD
Figure 32.
1. Remove the knockout from the fireplace and discard it
(see Figure 32).
2. Center the duct collar around the exposed hole and at-
tach it to the fireplace with 3 screws. NOTE: Do this BE-
FORE final positioning of the fireplace.
3. Determine the location for the air register/fan housing
assembly.
Figure 33. Gas Control System (IPI)
Reference the Heat-Zone kit instructions for the remaining
installation steps.
Standing Pilot Ignition System
This system includes millivolt control valve, standing pilot,
thermopile/thermocouple flame sensor, and piezo ignitor.
WARNING: 110-120 VAC MUST NEVER BE
CONNECTED TO A CONTROL VALVE IN A
MILLIVOLT SYSTEM.
!
Figure 34. Gas Control System (Standing Pilot)
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Step 7. The Gas Supply Line
NOTE: Have the gas supply line installed in accordance
with local building codes by a qualified installer ap-
proved and/or licensed as required by the locality. (In
the Commonwealth of Massachusetts installation must
be performed by a licensed plumber or gas fitter).
Use a wrench on
shut-off valve when
tightening gas line.
NOTE: Before the first firing of the fireplace, the gas
supply line should be purged of any trapped air.
MANUAL
SHUT-OFF
VALVE
NOTE: Consult local building codes to properly size
the gas supply line leading to the 1/2 inch (13mm)
hook-up at the unit.
GAS
VALVE
This gas fireplace is designed to accept a 1/2 inch
(13 mm) gas supply line. To install the gas supply line:
CONTROL
VALVE
• A listed (and Commonwealth of Massachusetts approved)
1/2 inch (13mm) tee-handle manual shut-off valve and a
listed flexible gas connector are connected to the 1/2
inch (13mm) inlet of the control valve. NOTE: If substi-
tuting for these components, please consult local codes
for compliance.
FLEX
CONNECTOR
GAS LINE
ACCESS HOLE
Figure 35. Gas Supply Line
Step 8. Gas Pressure Requirements
• Locate the gas line access hole in the outer casing of
the fireplace.
Pressure requirements for Heat & Glo gas fireplaces are
shown in the table below.
• The gas line may be run from either side of the fireplace
provided the hole in the outer wrap does not exceed 2 1/2”
in diameter and it does not penetrate the actual firebox.
Pressure
Natural Gas
Propane
Minimum
Inlet Pressure
5.0 inches
w.c.
11.0 inches
w.c.
• The gap between the supply piping and gas access hole
can be plugged with non-combustible insulation to pre-
vent cold air infiltration.
Maximum Inlet
Gas Pressure
14.0 inches
w.c.
14.0 inches
w.c.
• Open the fireplace lower grille, insert the gas supply line
through the gas line hole, and connect it to the shut-off valve.
Manifold
Pressure
3.5 inches
w.c.
10.0 inches
w.c.
• When attaching the pipe, support the control so that the
lines are not bent or torn.
A one-eighth (1/8) inch (3 mm) N.P.T. plugged tapping is
provided on the inlet and outlet side of the gas control for a
test gauge connection to measure the manifold pressure.
Use a small flat blade screwdriver to crack open the screw
in the center of the tap. Position a rubber hose over the tap
to obtain the pressure reading.
• After the gas line installation is complete, use a com-
mercially-available, non-corrosive leak check solution to
carefully check all gas connections for leaks.
WARNING: DO NOT USE AN OPEN FLAME TO
!
CHECK FOR GAS LEAKS.
The fireplace and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of the system at test pressures in
excess of one-half (1/2) psig (3.5 kPa).
• At the gas line access hole, use insulation to re-pack
the space around the gas pipe.
• Insert insulation from the outside of the fireplace and
pack the insulation tightly to totally seal between the
pipe and the outer casing.
The fireplace must be isolated from the gas supply piping
system by closing its individual shut-off valve during any
pressure testing of the gas supply piping system at test
pressures equal to or less than one-half (1/2) psig (3.5 kPa).
28
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
INTERMITTENT
PILOT
I
IGNITION MODULE
3 VAC
PLUG-IN
3V TRANSFORMER
IGNITOR
ON/OFF
WALL
S
SWITCH
FLAME SPARKER/
SENSOR
IGNITION
MODULE
(3V)
WHT
ORG
LOW VOLTAGE
SEE NOTE 1
VALVE
GROUND TO
FIREPLACE
CHASSIS
GROUND
REMOTE
CONTROL
HOT
NEUTRAL
WHITE WIRE
CAN BE
PLUGGED
INTO ANY
OF #1-#5
LOCATIONS
ON THE
BLACK WIRE CAN BE
PLUGGED INTO ANY OF
#1 - #5 LOCATIONS
ON THE HOT SIDE
PIGGYBACK
ON/OFF SWITCH
NEUTRAL SIDE
TRANSFORMER
3 VAC
PLUG IN
VALVE
Figure 36. Intermittent Pilot Ignition (IPI) Wiring Diagram
REMOTE SWITCH
PIGTAIL
3/16” PIGGYBACK CONNECTOR
BLACK S2
ON
OFF
TH
TP
ON/OFF
SWITCH
WHITE T2
GAS VALVE
RED T1
THERMOPILE
BLACK S1
THERMOCOUPLE
OPTIONAL WALL SWITCH,
THERMOSTAT OR REMOTE
Figure 37. Standing Pilot (SP) Ignition Wiring Diagram
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Optional Accessories
Step 9. Wiring the Fireplace
Optional fan and remote control kits require that 110-120
VAC be wired to the factory installed junction box before
the fireplace is permanently installed (see Figure 38)
Intermittent Pilot Ignition (IPI) Wiring
3 Volt Transformer
This appliance comes with a 3 volt transformer found in the
manual bag. Plug the transformer leads to the green con-
trol module (see Figure 36). Then plug the transformer into
the side outlet on the junction box.
Wall Switch
Position the wall switch in the desired position on a wall.
Run a maximum of 25 feet (7.8 m) or less length of 18
A.W.G. minimum wire and connect it to the fireplace ON/
OFF switch pigtails.
Appliance Requirements
• This appliance DOES NOT require 110-120 VAC to operate.
CAUTION: LABEL ALL WIRES PRIOR TO DISCONNEC-
TION WHEN SERVICING CONTROLS. WIRING ERRORS
CAN CAUSE IMPROPERAND DANGEROUS OPERATION.
VERIFY PROPER OPERATION AFTER SERVICING.
WARNING: DO NOT CONNECT 110-120 VAC
TO THE GAS CONTROL VALVE OR THE AP-
PLIANCE WILL MALFUNCTION AND THE
VALVE WILL BE DESTROYED.
!
Operation using Battery Power
NOTE: Electrical wiring must be installed by a licensed
electrician.
This fireplace has an optional battery operation. The sys-
tem is fully functional with the use of two “D” size batteries
without ordinary 110-120 VAC power.
CAUTION: DISCONNECT REMOTE CONTROLS IF AB-
SENT FOR EXTENDED TIME PERIODS. THIS WILL PRE-
VENT ACCIDENTAL FIREPLACE OPERATION.
Wiring to the battery pack should be left disconnected in
order to conserve battery life. In the case of a loss of power,
simply connect red and black wire leads to activate battery
power (connect red to red, black to black). The fireplace
can be used as necessary. Once power (110 VAC) is re-
stored, disconnect red and black wire leads to extend bat-
tery life.
For Standing Pilot Ignition Wiring (see Figure 37).
Appliance Requirements
• This appliance DOES NOT require 110-120 VAC to operate.
WARNING: DO NOT CONNECT 110-120 VAC TO
!
THE GAS CONTROL VALVE OR WALL SWITCH
OR THE APPLIANCE WILL MALFUNCTION
AND THE VALVE WILL BE DESTROYED.
VARIABLE SPEED CONTROL
NOTE: IF ANY OF THE ORIGINAL WIRE
AS SUPPLIED WITH THE APPLIANCE
MUST BE REPLACED, IT MUST BE
JUNCTION BOX
REPLACED WITH TYPE 105OC RATED WIRE.
BLK
BLK
BLOWER RECEPTACLE
BLK
BLK
BLK
BLK
BLK
WHT
GROUND
WHT
BLK
TEMPERATURE
SENSOR SWITCH
BLOWER
GRN
BLK
WHT
110-120 VAC
SENSOR
SWITCH
BLOWER
“FAN”
RECEPTACLE
SPEED
CONTROL
Figure 38. Fan Wiring Diagram
30
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: IF JOINTS BETWEEN THE FINISHED WALLS
AND THE FIREPLACE SURROUND (TOP AND SIDES)
ARE SEALED, A 300° F. MINIMUM SEALANT MATE-
RIAL MUST BE USED. THESE JOINTS ARE NOT RE-
QUIRED TO BE SEALED. ONLY NON-COMBUSTIBLE
MATERIAL (USING 300° F. MINIMUM ADHESIVE, IF
NEEDED) CAN BE APPLIED AS FACING TO THE FIRE-
PLACE SURROUND. SEE THE DIAGRAM BELOW.
Step 10. Finishing
Figure 39 shows the minimum vertical and corresponding
maximum horizontal dimensions of fireplace mantels or other
combustible projections above the top front edge of the
fireplace. See Figures 2 and 3 for other fireplace clearances.
Only non-combustible materials may be used to cover the
black fireplace front.
WARNING: WHEN FINISHING THE FIREPLACE,
NEVER OBSTRUCT OR MODIFY THE AIR IN-
FINISH WALL MATERIAL MAY BE
COMBUSTIBLE - TOP AND SIDES
!
LET/OUTLET GRILLES IN ANY MANNER.
NON-COMBUSTIBLE
BOARD
0”
12”
11”
10”
31”
9”
TO CEILING
8”
7”
18”
6”
17”
5”
16”
4”
15”
3”
14”
13”
12”
0”
0”
11”
2-1/2”
10”
HIGH TEMPERATURE (3000F/ 1490C MIN.)
TOP & SIDE SEAL JOINT
9”
4”
1”
Figure 40. Sealant Material
1”
TOP FRONT EDGE OF FIREPLACE
Hearth Extensions
A hearth extension may be desirable for aesthetic reasons.
However,ANSI or CAN/CGAtesting standards do not require
hearth extensions for gas fireplace appliances.
Figure 39.
Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles above Fireplace
Note: There are 3 metal tabs holding the non-combustible
board in place for shipping. These tabs are to be cut off or
bent back before finishing around the fireplace front.
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Step 11. Installing Trim, Logs,
and Ember Material
Installing the Trim
Combustible materials may be brought up to the specified
clearances on the side and top front edges of the fireplace,
but MUST NEVER overlap onto the front face. The joints
between the finished wall and the fireplace top and sides
can only be sealed with a 300° F. (149° C) minimum sealant.
LATCHES
(BOTH BOTTOM
AND TOP)
WARNING: WHEN FINISHING THE FIREPLACE,
NEVER OBSTRUCT OR MODIFY THE AIR INLET/
GLASS
ASSEMBLY
!
OUTLET GRILLES IN ANY MANNER.
Figure 42. Glass Assembly
Install optional marble and brass trim surround kits as
desired. Marble, brass, brick, tile, or other non-combustible
materials can be used to cover up the gap between the
sheet rock and the fireplace.
• Embers CANNOT be placed directly over ports. Care
should be taken not to cover the lighting trail of ports
(from back to front).
Do not obstruct or modify the air inlet/outlet grilles. When
overlapping on both sides, leave enough space so that the
bottom grille can be lowered and the trim door removed.
• When placing Glowing embers onto the burner care
should be taken so that the ports are not covered. Place
the embers along side the port trail, but not on or in
between the ports (see Figure 43). Failure to follow this
procedure will likely cause lighting and sooting problems.
RETAINING
SCREW
(BOTH SIDES)
BURNER
EMBER MATERIAL
Figure 41.
Burner Removal
Figure 43. Placement of the Ember Material
Shutter Settings
• Place Mystic embers on areas of base refractory away
from port holes. Use this material to give your fireplace a
realistic ash bed.
NG
LP
___________________________________________
Log
3/8”
3/8”
___________________________________________
• Save the remaining ember materials for use during fire-
place servicing.
Burner
3/16”
FULL OPEN
• Replace the glass door and a front trim door on the unit.
Positioning the Logs
• Pull out and latch the glass clips into the groove on the
glass frame.
If the gas logs have been factory installed they should not
need to be positioned. If the logs have been packaged
separately, refer to the instructions that accompany the
logs. Save the log instructions with this manual.
Glass Specifications:
6000TRI-SP: TEMPERED
6000TRI-IPI: TEMPERED
If sooting occurs, the logs might need to be repositioned
slightly to avoid excessive flame impingement.
Heat & Glo fireplaces manufactured with tempered glass
may be installed in hazardous locations such as bathtub
enclosures as defined by the CPSC. The tempered glass
has been tested and certified to the requirements of ANSI
Z97.1-1984 and CPSC 16 CFR 1202. (Safety Glazing Certi-
fication Council SGCC # 1595 and 1597. Architectural Test-
ing, Inc. Reports 02-31919.01 and 02-31917.01.)
Placing the Ember Material
Ember material is shipped with this gas fireplace. To place
the ember material:
• Pull the four glass latches out of the groove on the glass
frame. Remove glass door from the unit (see Figure 42).
32
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
This statement is in compliance with SPCS 16 CFR Sec-
tion 1201.5 “Certification and labeling requirements” which
refers to 15 USC 2063 stating “…Such certificate shall ac-
company the product or shall otherwise be furnished to any
distributor or retailer to whom the product is delivered.”
NOTE: The fireplace should be run 3 to 4 hours on the
initial start-up. Turn it off and let it cool completely. Remove
and clean the glass. Replace the glass and run the fireplace
for an additional 8 hours. This will help to cure the products
used in the paint and logs.
Some local building codes require the use of tempered glass
with permanent marking in such locations. Glass meeting
this requirement is available from the factory. Please con-
tact your dealer or distributor to order.
During this break-in period it is recommended that some
windows in the house be opened for air circulation. This will
help avoid setting off smoke detectors, and help eliminate
any odors associated with the fireplace’s initial burning.
Step 12. Before Lighting the Fireplace
Air Shutter Setting
Before lighting the fireplace, be sure to do the following:
This fireplace has an adjustable air shutter (which controls
the primary air) factory set for the minimum vertical vent run
(see Figure 44). If your installation has more than the
minimum required vertical vent length, adjustment of the air
shutter may be necessary to obtain optimal flame
appearance. This should be adjusted by a qualified
installer at the time of installation.
Remove all paperwork from underneath the fireplace.
Review safety warnings and cautions
• Read the Safety and Warning Information section at
the beginning of this Installers Guide.
Double-check for gas leaks
• Before lighting the fireplace, double-check the unit for
possible gas leaks.
By pushing the air shutter handle in, you will be closing the
air shutter. To adjust loosen the wing nut. Care should be
taken when adjusting the air shutter so as not to cause the
fireplace to soot. If sooting occurs the air shutter will need
to be opened by pulling the handle out. When finished tighten
wing nut.
Double-check vent terminations and front grilles for
obstructions.
• Before lighting the fireplace, double-check the unit for
possible obstructions that could be blocking the vent ter-
minations or the front grilles.
Double-check for faulty components
• Any component that is found to be faulty MUST BE re-
placed with an approved component. Tampering with the
fireplace components is DANGEROUS and voids all war-
ranties.
A small amount of air will be in the gas supply lines. When
first lighting the fireplace, it will take a few minutes for the
lines to purge themselves of this air. Once the purging is
complete, the fireplace will light and will operate normally.
Subsequent lightings of the fireplace will not require this
purging of air from the gas supply lines, unless the gas
valve has been turned to the OFF position, in which
case the air would have to be purged.
AIR SHUTTER
WING NUT
Figure 44.
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Step 13. Lighting the Fireplace
WARNING: PLEASE REFER TO THE USER’S
MANUALFORALL CAUTIONS, SAFETY, AND
WARNING INFORMATION PERTAINING TO THE
LIGHTING AND OPERATION OF THE FIREPLACE.
!
You’ve reviewed all safety warnings, you’ve checked the
fireplace for gas leaks, you know the vent system is
unobstructed, and you’ve checked for faulty components.
Now you’re ready to light the fireplace.
After the Installation
LEAVE THIS INSTALLATION MANUAL WITH
THE APPLIANCE FOR FUTURE REFERENCE.
!
Maintaining and Servicing Your Fireplace
4
Fireplace Maintenance
Although the frequency of your fireplace servicing and main-
tenance will depend on use and the type of installation, you
should have a qualified service technician perform an appli-
ance check-up at the beginning of each heating season.
See the table below for specific guidelines regarding each
fireplace maintenance task.
IMPORTANT: TURN OFF THE GAS BEFORE SERVICING
YOUR FIREPLACE.
Replacing old ember material
Frequency: Once annually, during the checkup.
By: Qualified service technician.
MAKE SURE THE FLAMES
ARE STEADY—NOT
LIFTING OR FLOATING.
Task: Brush away loose ember material near the burner.
Replace old ember material with new Mystic Ember pieces.
Save the remaining ember material and repeat this procedure
at your next servicing. For more information, see Placing
Ember Material.
Figure 45.
Burner Flame Patterns
Cleaning Burner and Controls
Frequency: Once annually.
Checking Vent System
Frequency: Before initial use and at least annually
thereafter, more frequently if possible.
By: Qualified service technician/Home owner.
Task: Inspect the external vent cap on a regular basis to
ensure that no debris is interfering with the flow of air. Inspect
entire vent system for proper function.
By: Qualified service technician.
Task: Brush or vacuum the control compartment, fireplace
logs and burner areas surrounding the logs.
Cleaning Flame Sensor Rod (IPI Systems)
Frequency: Annually.
By: Qualified service technician.
Cleaning Glass Door
Frequency: After the first 3 to 4 hours of use. As neces-
sary after initial cleaning.
Task: Make a visual check of the straight flame sensor rod
(see Figure 33). Use emery cloth to carefully remove any
existing film or white deposits.
By: Home owner.
Task: Remove and clean glass after the first 3 to 4 hours of
use. After the initial cleaning, clean as necessary, particu-
larly after adding new ember (flame colorant) material. Film
deposits on the inside of the glass door should be cleaned
off using a household glass cleaner. NOTE: DO NOT handle
or attempt to clean the door when it is hot and DO
NOT use abrasive cleaners.
Checking Flame Patterns, Flame Height
Frequency: Periodically.
By: Qualified service technician/Home owner.
Task: Make a visual check of your fireplace’s flame pat-
terns. Make sure the flames are steady - not lifting or
floating. See Figure 45. The flame sensor (IPI) or thermo-
pile/thermocouple tips should be covered with flame. See
Figure 34.
34
Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
|