Hearth and Home Technologies Stove 21M ACC User Manual
R
2100 MILLENNIUM WOOD STOVE  
Advanced Combustion Control (ACC)  
Owner’s Manual  
Installation and Operation  
Portland  
Oregon USA  
Tested and  
Listed by  
O-T L  
C
US  
OMNI-Test Laboratories, Inc.  
Model:  
21M-ACC  
NOTICE  
DO NOT DISCARD THIS MANUAL  
•
Read, understand and  
follow these instructions  
for safe installation and  
operation.  
•
Leave this manual with  
party responsible for  
use and operation.  
•
Important operating  
and maintenance  
instructions included.  
WARNING  
WARNING  
If the information in these instruc-  
tions is not followed exactly, a  
fire may result causing property  
damage, personal injury, or death.  
HOT SURFACES!  
Glass and other surfaces are  
hot during operation AND  
cool down.  
• Do not store or use gasoline or other flam-  
mable vapors and liquids in the vicinity of  
this or any other appliance.  
Hot glass will cause burns.  
•
•
•
•
Do not touch glass until it is cooled  
NEVER allow children to touch glass  
Keep children away  
CAREFULLY SUPERVISE children in same room  
as fireplace.  
• Do not overfire - If heater or chimney con-  
nector glows, you are overfiring. Overfiring  
will void your warranty.  
•
Alert children and adults to hazards of high  
temperatures.  
• Comply with all minimum clearances to  
combustibles as specified. Failure to  
comply may cause house fire.  
High temperatures may ignite clothing or other  
flammable materials.  
•
Keep clothing, furniture, draperies and other  
flammable materials away.  
Installation and service of this appliance should  
be performed by qualified personnel. Hearth &  
Home Technologies recommends NFI certified  
professionals, or technicians supervised by an  
NFI certified professional.  
WARNING  
Fire Risk.  
For use with solid wood fuel only.  
Other fuels may overfire and generate  
poisonous gases (i.e. carbon monoxide).  
www.quadrafire.com  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
TABLE OF CONTENTS  
Section 9: Maintaining & Servicing Appliance  
A. General Maintenance & Cleaning.......27  
B. Glass Replacement.............................28  
C. Firebrick Replacement........................29  
D. Baffle Removal....................................30  
E. Snap Disc Replacement .....................30  
F. Tube Channel Replacement ...............31  
Section 1: Listing and Code Approvals  
A. Appliance Certifications ......................4  
B. Mobile Home Approved ......................4  
C. Glass Specifications............................4  
D. BTU & Efficiency Specifications..........4  
Section 2: Getting Started  
A. Design, Installation & Location  
Section 10: Troubleshooting........................ꢀ2  
Considerations....................................5  
B. Fire Safety ..........................................5  
C. Negative Pressure ..............................6  
D. Flue Draft Considerations...................7  
E. Venting Systems.................................7  
F. Tools and Supplies Needed................7  
G. Inspect Appliance & Components.......7  
H. Typical Stove System .........................8  
Section 11: Reference Material  
A. Exploded Drawings.............................33-34  
B. Service Parts & Accessories...............35-36  
C. Service & Maintenance Log................ꢀ7-ꢀ8  
D. Homeowner’s Notes ...........................39-40  
E. Warranty Policy...................................41-42  
F. Contact Information.............................44  
Section 3: Dimensions & Clearances  
A. Appliance Dimensions ........................9  
B. Clearances to Combustibles...............10  
Section 4: Installation Consideration  
A. Hearth Requirements .........................11  
B. Outside Air..........................................12  
C. Blower Installation...............................13  
Section 5: Chimney Requirements  
A. Venting Components..........................14  
B. Chimney Systems...............................14-16  
C. Installing Chimney Components .........16  
D. Chimney Termination Requirements ..17  
E. 2-10-ꢀ Rule..........................................17  
Section 6: Mobile Home...............................18  
Section 7: Appliance Set-Up  
C. Door Handle Assembly.......................19  
D. Blower Speed Adjustment ..................19  
Section 8: Operating Instructions  
A. Overfiring Your Appliance...................20  
B. Wood Selection & Storage..................20  
C. Burning Process..................................20-21  
D. Automatic Combustion Control (ACC)....21  
E. Air Controls .........................................21-22  
F. Burn Rates & Operating Efficiency .....22  
G. Building A Fire.....................................2ꢀ  
H. Correct Baffle & Blanket Placement....24  
I. Blower Operating Instructions.............25  
J. Opacity (Smoke) .................................25  
K. Frequently Asked Questions...............26  
Page ꢀ  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
Listing and Code Approvals  
1
D. BTU & Efficiency Specifications  
A. Appliance Certification  
2100 Millennium (ACC)  
2.1 grams per hour  
Model:  
EPA Certified:  
Number: 664  
Issued: 07-20-2007  
Laboratory:  
Report No & Date:  
Type:  
OMNI Test Laboratories, Inc.  
061-S-70-6  
EPA Certificate Number  
and Date:  
78.15%  
Efficiency:  
Listed Room Heater, Solid Fuel Type  
12,000 to 28,800  
BTU Output:  
Heating Capacity:  
Standard:  
UL1482 and ULC S627-00 and  
(UM) 84-HUD, Mobile Home  
Approved.  
800 to 1,500 sq ft  
depending on climate zone  
6 inches  
Vent Size:  
The Quadra-Fire 2100 Millennium Wood Stove (ACC) meets  
the U.S. Environmental ProtectionAgency’s 1990 particulate  
emission standards.  
1.46 cubic feet  
16 inches  
Cord Wood  
ꢀ00 lbs  
Firebox Size:  
Max Wood Length:  
Fuel:  
Shipping Weight:  
B. Mobile Home Approved  
This appliance is approved for mobile home installations  
when not installed in a sleeping room and when an outside  
combustion air inlet is provided. The structural integrity of  
the mobile home floor, ceiling, and walls must be maintained.  
The appliance must be properly grounded to the frame of  
the mobile home and use only listed double-wall connector  
pipe. Outside Air Kit, part OAK-ACC must be installed in a  
mobile home installation  
NOTE: Hearth & Home Technologies, manufacturer of  
this appliance, reserves the right to alter its products,  
their specifications and/or price without notice.  
C. Glass Specifications  
This stove is equipped with 5mm ceramic glass. Replace  
glass only with 5mm ceramic glass. Please contact your  
dealer for replacement glass.  
NOTE: This installation must conform with local codes. In the  
absence of local codes you must comply with the UL1482, (UM)  
84-HUD and NPFA211 in the U.S.A. and the ULC S627-00 and  
CAN/CSA-B365 Installation Codes in Canada.  
Page 4  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
Getting Started  
2
B. Fire Safety  
A
. Design, Installation & Location Considerations  
Consideration must be given to:  
To provide reasonable fire safety, the following should be  
given serious consideration:  
•
•
•
•
Safety  
Convenience  
Traffic flow  
Chimney and chimney connector required  
1. Install at least one smoke detector on each floor of  
your home to ensure your safety. They should be  
located away from the heating appliance and close  
to the sleeping areas. Follow the smoke detector  
manufacturer’s placement and installation instructions,  
and be sure to maintain regularly.  
It is a good idea to plan your installation on paper, using exact  
measurements for clearances and floor protection, before  
actually beginning the installation. If you are not using an  
existing chimney, place the appliance where there will be a  
clear passage for a factory-built listed chimney through the  
ceiling and roof.  
2. A conveniently located Class A fire extinguisher  
to contend with small fires resulting from burning  
embers.  
We recommend that a qualified building inspector and your  
insurance company representative review your plans before  
and after installation  
ꢀ. A practiced evacuation plan, consisting of at least two  
escape routes.  
4. A plan to deal with a chimney fire as follows:  
In the event of a chimney fire:  
If this appliance is in an area where children may be near it  
is recommended that you purchase a decorative barrier to go  
in front of the appliance. Remember to always keep children  
away while it is operating and do not let anyone operate  
this appliance unless they are familiar with these operating  
instructions.  
a
Evacuate the house immediately  
b. Notify fire department  
WARNING  
NOTE: Service Space  
Fire Risk.  
In order to replace the tube channel a clearance of 17  
inches (4ꢀ2mm) is required on the right side of stove in  
order to remove the tubes with the stove in place.  
Hearth & Home Technologies disclaims any  
responsibility for, and the warranty will be  
voided by, the following actions:  
•
•
•
Installation and use of any damaged appliance.  
If space is not available, the stove will have to be discon-  
nected from the chimney to proceed with the tube replace-  
ment. See page 31.  
Modification of the appliance.  
Installation other than as instructed by Hearth & Home  
Technologies.  
•
•
•
•
Installation and/or use of any component part not approved  
by Hearth & Home Technologies.  
CAUTION  
Operating appliance without fully assembling all  
components.  
Check building codes prior to installation.  
•
Installation MUST comply with local, regional, state and  
national codes and regulations.  
Operating appliance without legs attached (if supplied with  
unit).  
•
Consult insurance carrier, local building, fire officials or  
authorities having jurisdiction about restrictions, installation  
inspection, and permits.  
Do NOT Overfire - If appliance or chimney connector glows,  
you are overfiring.  
Any such action that may cause a fire hazard.  
WARNING  
WARNING  
Asphyxiation Risk.  
Fire Risk.  
•
Do NOT connect this unit to a chimney flue  
servicing another appliance.  
•
Do not operate appliance before reading and  
understanding operating instructions.  
•
Do NOT connect to any air distribution duct or  
system.  
•
Failure to operate appliance properly may  
cause a house fire.  
May allow flue gases to enter the house.  
Page 5  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
C. Negative Pressure  
To minimize the affects of negative air pressure the following  
must be considered:  
Draft is the pressure difference needed to vent appliances  
successfully. Considerations for successful draft include:  
•
Install the outside air kit. Install the intake on the  
side of the house towards prevailing winds during the  
heating season.  
•
•
Preventing negative pressure  
Location of appliance and chimney  
•
•
Ensure adequate outdoor air is supplied for combus-  
tion appliances and exhaust equipment.  
Negative pressure results from the imbalance of air avail-  
able for the stove to operate properly. Causes for this imbal-  
ance include:  
Ensure furnace and air conditioning return vents are  
not located in the immediate vicinity of the appli-  
ance,  
•
•
•
Exhaust fans (kitchen, bath) etc.)  
Range hoods  
•
•
Avoid installing the appliance near doors, walkways  
or small isolated spaces.  
Combustion air requirements for furnaces, water  
heaters and other combustion appliances  
Recessed lighting should be of “sealed can” design;  
attic hatches weather stripped or sealed; and attic  
mounted ductwork and air handler joints and seams  
taped or sealed.  
•
•
Clothes dryers  
Location of return-air vents to furnace or air condi-  
tioning  
•
•
Imbalances of HVAC air handling system  
Upper level air leaks  
•
•
•
Recessed lighting  
Attic hatch opening  
Duct leaks  
WARNING  
Asphyxiation Risk.  
•
•
Negative pressure can cause spillage of com-  
bustion fumes, soot and carbon monoxide.  
Appliance needs to draft properly for safety.  
Recommended Location:  
• Above peak  
• Inside heated space  
Recommended Location:  
• Above peak  
Marginal Location:  
Wind loading possible  
•
Marginal Location:  
• Below peak  
Location NOT recommended:  
• Not the highest point of the roof  
• Wind loading possible  
Location NOT recommended:  
• Too close to tree  
• Below adjacent structure  
• Lower roof line  
Recommended:  
• Insulated exterior chase  
in cooler climates  
• Avoid outside wall  
Windward  
Leeward  
Multi-level Roofs  
Recommended:  
Outside Air Intake  
on windward side  
NOT recommended:  
Outside Air Intake  
on leeward side  
Figure 6.1  
Page 6  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
F. Tools And Supplies Needed  
D. Flue Draft Considerations  
Location of the appliance and chimney will affect perfor-  
mance. As shown in Figure 6.1 on page 6 the chimney  
should:  
Before beginning the installation be sure that the following  
tools and building supplies are available.  
•
Be installed through the warm space enclosed by the  
building envelope. This helps to produce more draft,  
especially during lighting and die down of the fire.  
Framing Material  
Hi-Temp Caulking Material  
Gloves  
Reciprocating saw  
Pliers  
Hammer  
Framing Square  
Electric Drill & Bits (1/4”)  
Safety Glasses  
1/2 in. - ꢀ/4 in. length, #6 or  
#8 self drilling screws (need ꢀ  
per pipe section connection)  
Phillips Head Screwdriver  
Flat Blade Screwdriver  
Plumb Line  
Level  
Tape Measure  
•
•
Penetrate the highest part of the roof. This minimizes  
the affects of wind turbulence and down drafts.  
Consider the appliance location in order to avoid  
floor and ceiling attic joists and rafters.  
Exterior conditions such as roof line, surrounding trees,  
prevailing winds and nearby hills can influence stove  
performance. Your local dealer is the expert in your geographic  
area and can usually make suggestions or discover solutions  
that will easily correct your flue problem.  
G. Inspect Appliance & Components and  
Pre-Use Check List  
T
o be sure that your appliance burns properly, the chimney  
draft (static pressure) should be approximately -.04 inch water  
column (W.C.) during a low burn and -.10 inch W.C. during a  
high burn, measured 6 inches (152mm) above the top of the  
appliance after one hour of operation at each burn setting.  
1.  
Place the appliance in a location near the final  
installation area and follow the procedures below:  
2.  
Open the appliance and remove all the parts and  
articles packed inside the Component Pack. Inspect  
all the parts and glass for shipping damage. Contact  
your dealer if any irregularities are noticed.  
NOTE: These are guidelines only, and may vary somewhat  
for individual installations.  
3.  
4.  
5.  
6.  
7.  
All safety warnings have been read and followed.  
This Owner’s Manual has been read.  
Floor protection requirements have been met.  
Venting is properly installed.  
E. Venting Systems  
The venting system consists of a chimney connector (also  
known as stove pipe) and a chimney. These get extremely  
hot during use. Temperatures inside the chimney may  
exceed 2000°F (1100°C) in the event of a creosote fire. To  
protect against the possibility of a house fire, the chimney  
connector and chimney must be properly installed and  
maintained. An approved thimble must be used when a  
connection is made through a combustible wall to a chimney.  
Achimney support package must be used when a connection  
is made through the ceiling to a prefabricated chimney.  
These accessories are absolutely necessary to provide  
safe clearances to combustible wall and ceiling material.  
Follow venting manufacturer’s clearances when installing  
venting system.  
The proper clearances from the appliance and chim-  
ney to combustible materials have been met.  
8.  
The masonry chimney is inspected by a professional  
and is clean, or the factory built metal chimney is  
installed according to the manufacturer’s instruc-  
tions and clearances.  
9.  
The chimney meets the required minimum height.  
All labels have been removed from the glass door.  
10.  
11.  
A power outlet is available nearby if installing  
optional blower assembly.  
WARNING  
WARNING  
Fire Risk.  
Asphyxiation Risk.  
Inspect appliance and components for damage.  
Damaged parts may impair safe operation.  
•
Do NOT connect this unit to a chimney flue  
servicing another appliance.  
•
•
•
Do NOT install damaged components.  
Do NOT install incomplete components.  
Do NOT install substitute components.  
•
Do NOT connect to any air distributon duct  
or system.  
May allow flue gases to enter the house.  
Report damaged parts to dealer.  
Page 7  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
H. Typical Stove Systems  
Spark Arrestor Cap  
Concrete Cap  
Fireclay Flue Liner  
With Air Space  
Stove system with masonry chimney  
consists of:  
Rafter  
• Stove  
Flashing  
Eave  
• Chimney Connector (stove pipe)  
• Thimble  
1" (25mm) Clearance  
With Firestop  
Ceiling Joist  
• Masonry Chimney  
• Hearth Pad Floor Protection  
Combustible Wall  
Thimble,  
12" (305mm)  
Of Brick  
Sheathing  
Outside Air Rear Vent  
Outside Air  
Termination Cap  
Floor  
Protector  
Airtight  
Cleanout Door  
Figure 8.1 Masonry Chimney  
Stove system with prefabricated  
metal chimney consists of:  
Listed Termination Cap  
Storm Collar  
Flashing  
Listed Termination Cap  
• Stove  
Chimney Connector  
(stove pipe)  
•
Roof Brace (if required)  
• Thimble (for exterior  
chimney)  
Storm Collar  
Flashing  
Listed Chimney  
Ceiling Support  
• Firestops  
• Insulations Shields  
• Storm Collar and Flashing  
• Termination Cap  
Trim Collar on  
Inside Wall  
Listed Chimney  
Insulated " T "  
• Hearth Pad Floor Protec-  
Chimney  
Connector  
Chimney  
Connector  
tion  
Wall Support  
Thimble  
Floor  
Protector  
Floor  
Protector  
Figure 8.2 Exterior Prefabricated Chimney  
Figure 8.3 Interior Prefabricated Chimney  
Page 8  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
Dimensions and Clearances  
3
23-3/8 in. (594mm)  
A. Appliance Dimensions  
C
L
8-5/8 in.  
(219mm)  
11-11/16 in.  
(297mm)  
NOTE: Flue Collar size is 6 inch  
(152mm) diameter (ID)  
9-1/4 in. (235mm)  
12-3/4 in.  
(324mm)  
13-1/2 in. (342mm)  
17 in. (432mm)  
27-15/16 in.  
(709mm)  
Figure 9.1 Front View  
26-7/16 in. (671mm)  
24-5/16 in. (618mm)  
6-11/16 in.  
(170mm)  
C
L
11-1/2 in.  
(292mm)  
16 in. (406mm)  
C
4-1/2 in  
(108mm)  
L
Outside Air  
Connection  
20-3/4 in. (527mm)  
Figure 9.2 Side View  
Page 9  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
B. Clearances to Combustibles (UL and ULC)  
BACKWALL / SIDEWALL  
ALCOVE SIDE VIEW  
NOTE: Clearances may only be reduced by means  
approved by the regulatory authority having jurisdiction  
A
B
G
A
C
D
B
STOVE TO CEILING  
CLEARANCE  
CORNER INSTALLATION  
E
ALCOVE TOP VIEW  
F
C
D
E
F
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS In Inches & (Millimeters)  
NOTE: All "A" , "C" and "F" Dimensions are to the inside diameter of the flue collar.  
A
B
C
D
E
F
G
H
INSTALLATION: Full Vertical  
SINGLE WALL PIPE  
DOUBLE WALL PIPE  
15 (ꢀ81) 11 (279) 21.5 (546) 1ꢀ (ꢀꢀ0) 8.5 (216) 17(4ꢀ2) 56 (1422)  
N/A  
8.75(222) 5.75 (146) 20 (508) 10.5 (267) 7.5 (191) 16 (406) 4ꢀ (1092)  
N/A  
INSTALLATION: Horizontal with Minimum 2 Foot Vertical Off Stove Top  
SINGLE WALL PIPE  
DOUBLE WALL PIPE  
14 (ꢀ56) 10 (254) 20.5 (521) 12 (ꢀ05) 8.5 (216) 17 (4ꢀ2) 56 (1422)  
9.5 (241) 5.5 (140) 21.5 (546) 1ꢀ (ꢀꢀ0) 7.5 (191) 16 (406) 4ꢀ (1092)  
9.5 (241)  
5 (127)  
INSTALLATION: ALCOVE Six inch (6") (152mm) diameter listed double wall air insulated connector pipe with UL  
10ꢀ HT listed factory-built Class "A" chimney, or a masonry chimney. (Mobile Home must be equipped with a spark  
arrestor). Maximum depth of alcove shall be no more than 48"(1220mm) with a minimum height of 4ꢀ" (1092mm) to top  
of unit, and the referenced clearances.  
DOUBLE WALL PIPE  
9.5 (241) 5.5 (140) 21.5 (546) 1ꢀ (ꢀꢀ0)  
N/A  
N/A  
4ꢀ (1092)  
5 (127)  
NOTE: Service Space  
WARNING  
In order to replace the tube channel assembly a clearance  
of 17 inches (4ꢀ2mm) is required on the right side of stove  
in order to remove the tubes with the stove in place.  
Fire Risk.  
•
Comply with all minimum clearances to  
combustibles as specified.  
If space is not available, the stove will have to be discon-  
nected from the chimney to proceed with the tube replace-  
ment.  
•
Failure to comply may cause house fire.  
Page 10  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
Installation  
4
In Canada, similar floor protection must be provided 18  
inches (457mm) in front and 8 inches (20ꢀmm) from the  
sides and rear of the stove. *See exception.  
A. Hearth Protection Requirements  
FLOOR PROTECTION: Floor protector must be non-com-  
bustible material, extending beneath heater and to the front,  
sides and rear as indicated. The floor must be non-com-  
bustible or otherwise adequately protected from radiant heat  
given off by the unit and from sparks and falling embers. A  
layer of thin brick or ceramic tile over a combustible floor is  
not sufficient.  
*ExCEPTION: Non-combustible floor protections must  
extend beneath the flue pipe when installed with horizontal  
venting and extend 2 inches (51mm) beyond each side.  
See Figure 11.4.  
WARNING  
In US installations, it is necessary to install a floor protector  
of a minimum of ꢀ/8 inch (9.5mm) thick metal clad millboard  
or equivalent a minimum of 16 inches (406mm) in front of  
glass and 8 inches (20ꢀmm) to both sides of the fuel loading  
door. Open the door and measure 8 inches (20ꢀmm) from  
the side edge of the opening in the face of the appliance.  
*See exception.  
Fire Risk.  
• Hearth pads must be installed exactly as  
specified.  
High temperatures or hot embers may ignite  
concealed combustibles.  
50-ꢀ/4 in.  
l
a
.
e
n
o
g
in  
i
a
t
r
/8  
p
5
-
o
ve  
co  
9
2
ꢀ2-7/8 in.  
5-ꢀ/4 in.  
2-1/4 in."  
ꢀ6 in.  
minimum  
Fuel loading door  
°
5
3
1
.
in  
6
/1  
8 in.  
5
1
-
8
16" from glass  
ꢀ
.
in  
/8  
ꢀ
-
USA  
5
2
29-5/8 in.  
minimum  
USA  
ꢀ in.  
USA  
Figure 11.1  
Figure 11.3  
USA required  
Canada recommended  
203mm (8 in.)  
203mm  
(8 in.)  
203mm  
(8 in.)  
1168mm  
(46 in.)  
minimum  
457mm (18 in.)  
Must extend 2 in. (51mm) beyond  
each side of pipe (shaded area)  
1078mm (42-7/16 in.)  
minimum  
CANADA  
Figure 11.2  
NOTE:  
Figure 11.4  
•
•
•
•
Illustrations and photos reflect typical installations and are FOR DESIGN PURPOSES ONLY.  
Illustrations/diagrams are not drawn to scale.  
Actual installation may vary due to individual design preference  
Hearth & Home Technologies reserves the right to alter its products.  
Page 11  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
B. Outside Air Kit Installation  
A source of air (oxygen) is necessary in order for combus-  
tion to take place. Whatever combustion air is consumed  
by the fire must be replaced. Air is replaced via air leakage  
around windows and under doors. In homes that have tightly  
sealed doors and windows, an outside air source is needed.  
An optional Outside Air Kit is available.  
WARNING  
Fire Risk.  
Asphyxiation Risk.  
Do not draw outside combustion air from:  
•
•
•
Wall, floor or ceiling cavity  
Enclosed space such as an attic or garage  
Included in OAK-ACC: Termination cap, (2) wire ties, flex  
Close proximity to exhaust vents or chimneys  
adapter, and fasteners  
Fumes or odor may result  
Included in SRV7033-041:Cover plate and sealing rope (see  
Floor Installation Alternative below,  
Figure 12.2)  
WARNING  
Asphyxiation Risk.  
Items Needed for Installation (not supplied)  
Outside air inlet must be located to prevent blockage  
from:  
• 4 inch flex aluminum pipe, or if using alternate material,  
then it shall be made from durable, non-combustible, heat  
resistant material up to ꢀ50oF. Cut the pipe to the required  
length for your installation.  
•
•
•
Leaves  
Snow or ice  
Other debris  
• Phillips head screw driver  
• Silicone sealant  
Block may cause combustion air starvation  
Smoke spillage may set off alarms or irritate sensitive  
individuals.  
• Drills and saws necessary for cutting holes through the  
wall or flooring in your home  
WARNING  
1. Remove all materials from packing box.  
Asphyxiation Risk.  
2. Using a #2 Phillips screw driver attach the flex adapter to  
Length of outside air supply duct shall NOT exceed  
the length of the vertical height of the exhaust flue.  
the stove using 4 screws. Figure 12.1.  
ꢀ. Remove circular “knock-out” in the base of the pedestal.  
• Fire will not burn properly  
4. Floor & Rear Installation: Cut a 4 inch (102mm) hole in  
outside wall or floor to accommodate outside air piping.  
Use 4 inch (102mm) aluminum metal flex or rigid piping  
to directly connect outside air to appliance intake. Use  
the supplied termination cap with a rodent screen. Seal  
between the wall (or floor) and the pipe with silicone to  
prevent moisture penetration.  
• Smoke spillage occurs when door is opened due to  
air starvation.  
5. Floor Installation Alternative: In some instances you  
may not be able to install the flex pipe as show in Figure  
12.1. If that is the case, you will need to order SRV70ꢀꢀ-  
041 which includes a cover plate and sealing rope as  
shown in Figure 12.2. The goal is to seal the pedestal  
so no room air can leak into the pedestal.  
Flex Adapter  
Wire Tie  
Termination  
Cap  
Remove circular  
“knock-out” in base  
of pedestal.  
Cover  
Plate  
Flex Line  
Wire Tie  
Figure 12.2 - Floor Installation Alternative  
Figure 12.1 - Floor & Rear Installation  
Page 12  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
C. Blower (Optional)  
CAUTION  
1. Remove the ꢀ bolts (1/4”-20 Phillips head) on the outer  
skin at the bottom rear of appliance.  
Shock Risk.  
2. Align holes in mounting flange of blower with bolt holes in  
appliance. Blower should be positioned at bottom of rear  
outer skin as shown in Figure 13.1.  
•
Do NOT remove grounding prong from plug.  
•
Plug directly into properly grounded ꢀ prong  
receptacle.  
•
•
Route cord away from appliance.  
ꢀ. Re-insert and tighten bolts, securing blower onto outer  
wall of appliance.  
Do NOT route cord under or in front of appliance.  
4. Place the bracket containing the snap disc and magnet  
under the bottom left rear corner as shown in Figure 13.1.  
See page 25 for detailed operating instructions for the  
blower and snap disc.  
Snap Disc  
Bracket  
with Magnet  
Secure wires  
with wire tie  
MANUAL: Over-rides the  
Snap Disc  
MANUAL  
FAN  
AUTO  
AUTO: Fan will turn ON/OFF  
Automatically by the Snap Disc  
LOW  
HIGH  
OFF  
Controls the Fan Speed  
Figure 13.1  
Page 1ꢀ  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
Chimney Requirements  
5
A. Venting Components  
Chimney Connector:  
B. Chimney Systems  
Prefabricated Metal Chimney  
It is also known as flue pipe or stove pipe. The chimney  
connector joins the stove to the chimney. It must be a 6 inch  
(152mm) minimum diameter 24 gauge mild steel black or  
26 gauge blued steel, or an approved air-insulated double  
wall venting pipe.  
•
•
•
•
Must be a 6 inch (152mm) diameter (ID) high temperature  
chimney listed to UL 10ꢀ HT (2100 F) or ULC S629M.  
o
Must use components required by the manufacturer for  
installation.  
Must maintain clearances required by the manufacturer  
for installation.  
Thimble:  
A manufactured or site-constructed device installed in  
combustible walls through which the chimney connector  
passes to the chimney. It is intended to keep the walls  
from igniting. Site constructed thimbles must meet  
NFPA 211 Standards. Prefabricated must be suitable  
for use with selected chimney and meet UL10ꢀ Type HT  
Standards. Follow instructions provided by the manufacturer  
for manufactured thimbles for masonry chimney and  
prefabricated chimneys.  
Refer to manufacturers instructions for installation.  
NOTE: In Canada when using a factory-built chimney it must  
be safety listed, Type UL103 HT (2100oF) CLASS “A” or  
conforming to CAN/ULC-S629M, STANDARD FOR 650oC  
FACTORY-BUILT CHIMNEYS.  
Chimney:  
Listed Termination Cap  
Storm Collar  
Thechimneycanbeneworexisting, masonryorprefabricated  
and must meet the following minimum requirements specified  
in Section 5B.  
Flashing  
Listed Termination Cap  
Roof Brace (if required)  
Listed Chimney  
Ceiling Support  
Storm Collar  
Flashing  
Chimney  
Connector  
Trim Collar on  
Inside Wall  
Listed Chimney  
Insulated " T "  
Chimney  
Connector  
Wall Support  
Thimble  
Floor  
Protector  
Floor  
Protector  
Figure 14.2 - Prefabricated Interior Chimney  
Figure 14.1 Prefabricated Exterior Chimney  
Page 14  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
Thimble  
C
L
Site constructed for masonry chimney installation:  
ceiling  
Components  
13.5” below ceiling to top  
of opening  
• A minimum length of 12 inches [ꢀ05mm] (longer for  
thicker walls) of solid insulated factory-built chimney  
length constructed to UL 10ꢀ Type HT 6 inch (152mm)  
inside diameter. Chimney needs to extend a minimum  
of 2 inches (51mm) from the interior wall and a mini-  
mum of 1 inch (25mm) from the exterior wall.  
Wall  
or top of opening is a min.of  
4.5” below min.clearance  
specified by connector mfg.  
Minimum18.0”  
NFPA 211  
1.5 2x2 framing stud  
2.0 min air clearance  
1.0 min air clearance  
4.5  
1.5”  
2.0”  
1.0”  
• Wall spacer, trim collar and wall band to fit solid pack  
chimney selected.  
17.0” OD  
14.0” ID  
8.0”  
C
L
1.0”  
2.0”  
• Minimum 8 inch (20ꢀmm) diameter clay liner section (if  
not already present in chimney) and refractory mortar.  
1.5”  
Center of Hole  
Thimble  
Air Clearances  
• Masonry chimney clearance must meet NFPA 211 mini-  
mum requirement of 2 inches (51mm) to sheet metal  
supports and combustibles.  
Include depth  
of hearth pad  
• Minimum of 1 inch (25mm) clearance around the chim-  
ney connector.  
• Top of wall opening is a minimum of 1ꢀ-1/2 inches  
(ꢀ4ꢀmm) from ceiling or 4-1/2 inches (114mm) below  
minimum clearance specified by chimney connector  
manufacturer. NFPA 211 minimum vertical clearance of  
18 inches (457mm) from chimney connector and ceil-  
ing or minimum recommended by chimney connector  
manufacturer. Figure 15.1.  
Figure 15.1  
Solid Pack Chimney with Metal Supports as a Thimble  
Instructions:  
1. Open inside wall at proper height for the chimney con-  
nector to entry the masonry chimney. Figure 15.1  
Fire Clay Flue  
Liner  
with Airspace  
2. Entry hole to masonry chimney must be lined with an 8  
inch (20ꢀmm) minimum diameter clay liner, or equiva-  
lent, secured with refractory mortar.  
Masonry  
Chimney  
Trim Collar  
ꢀ. Construct a 17 inch x 17 inch (4ꢀ2mm x 4ꢀ2mm) out-  
side dimension frame from 2 x 2 framing lumber to  
fit into wall opening. Inside opening of frame should  
be no less than 14 inch x 14 inch (ꢀ56mm x ꢀ56mm).  
Figure 15.1.  
Wall Spacer  
Chimney Section  
with 2 inch  
(51mm)  
Clearance to  
Combustibles  
Wall Band to  
Secure Chimney  
Section  
4. Attach the wall spacer to the chimney side of the  
frame.  
Chimney  
Connector  
Wood Studs Used  
for Framing - Spaced  
2 inch (51mm)  
clearance from  
Masonry Chimney  
5. Nail the frame into the wall opening. The spacer should  
be on the chimney side.  
6. Insert the section of the solid insulated chimney into  
the outer wall of the masonry chimney.  
Figure 15.2  
7. Tightly secure the length of the solid insulated chimney  
with the wall band to the masonry chimney.  
WARNING  
Fire Risk.  
8. Insert a section of chimney connector into the chimney.  
Make sure it does not protrude past the edge of the  
clay chimney liner inside the chimney.  
Do NOT pack insulation or other combustibles between  
spacers.  
•
ALWAYS maintain specified clearances around vent-  
ing and spacers.  
9. Seal the end of the chimney connector to the clay liner  
with refractory mortar.  
•
Install spacers as specified.  
Failure to keep insulation or other material away from  
vent pipe may cause fire.  
10. Install trim collar around the sold pack chimney section  
.
Page 15  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
Solid Pack Chimney with Metal Supports as a  
Thimble (Cont’d)  
C. Installing Chimney Components  
Chimney Connector  
Single wall connector or stove pipe.  
Min. Chimney Clearance to  
This must be at least 24 gauge mild steel or 26 gauge blue  
steel. The sections must be attached to the appliance and to  
each other with the crimped (male) end pointing toward the  
stove. All joints, including the connection at the flue collar,  
should be secured with ꢀ sheet metal screws. Make sure  
to follow the minimum clearances to combustibles. Where  
passage through the wall, or partition of combustible con-  
struction is desired in Canada, the installation shall conform  
to CAN/CSA-Bꢀ65.  
Wall Spacer and  
Min. Clearance  
2 inch (51mm)  
Combustibles - 2 inch (51mm)  
1 inch (25mm) Air  
Space to Chimney  
Section  
Chimney Flue  
Liner  
Fireclay  
Liner or  
Equivalent  
Chimney  
Connector  
Chimney Section  
Trim Collar  
Wall Band  
Wall Spacer  
Factory-built listed chimney connector (vented).  
Alisted connector (vented) must be used when installing this  
unit in a mobile home. The listed connectors must conform  
to each other to ensure a proper fit and seal.  
Masonry Chimney  
Constructed to NFPA 211  
Figure 16.1  
Chimney Height / Rise and Run  
Crimped  
Flue Gas  
End  
This product was designed for and tested on a 6 inch (152mm)  
chimney, 14 to 16 feet (420-480cm) high, (includes stove  
height) measured from the base of the appliance. The further  
your stack height or diameter varies from this configuration,  
the possibility of performance problems exists.  
Direction  
Toward  
Stove  
Chimney height may need to be increased by 2 - ꢀ% per  
each 1000 feet above sea level. It is not recommended to  
use offsets or elbows at altitudes above 4000 feet above sea  
level or when there are other factors that affect flue draft.  
Secure pipe sections with a  
minimum of 3 screws  
Figure 16.2 Chimney Connector (Stove Pipe)  
WARNING  
WARNING  
Fire Risk.  
Fire Risk.  
Follow Chimney Connector Manufacturer’s  
Instructions for Proper Installation.  
Inspection of Chimney:  
•
•
•
Chimney must be in good condition.  
Meets minimum standard of NFPA 211  
ONLY use connector:  
•
Within the room, between appliance and ceiling or wall.  
Factory-built chimney must be 6 inch  
(152mm) UL10ꢀ HT.  
Connector shall NOT pass through:  
•
•
•
Attic or roof space  
Closet or similar concealed space  
Floor or ceiling  
Maintain minimum clearances to combustibles  
WARNING  
Asphyxiation Risk.  
WARNING  
•
Do NOT connect this unit to a chimney flue  
servicing another appliance.  
Improper installation, adjustment, alteration, service or  
maintenance can cause injury or property damage. Refer  
to the owner’s information manual provided with this appli-  
ance. For assistance or additional information consult a  
qualified installer, service agency or your dealer.  
•
Do NOT connect to any air distribution duct  
or system.  
May allow flue gases to enter the house.  
Page 16  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
D. Chimney Termination Requirements  
NOTE:  
Follow manufacturer’s instructions for clearance, securing  
flashing and terminating the chimney.  
•
•
Chimney performance may vary.  
Trees, buildings, roof lines and wind conditions affect  
performance.  
•
•
Must have an approved and listed cap  
•
Chimney height may need adjustment if smoking or  
overdraft occurs.  
Must not be located where it will become plugged by  
snow or other material  
•
Must terminate at least ꢀ feet (91cm) above the roof  
and at least 2 feet (61cm) above any portion of the  
roof within 10 feet (ꢀ05cm).  
•
Must be located away from trees or other struc-  
tures  
E. 2-10-3 Rule  
These are safety requirements and are not meant to assure proper flue draft.  
Less than 10 ft. (305cm)  
2 ft. (61cm)  
3 ft. (91cm)  
Minimum  
2 ft. (61cm)  
10 ft. (305cm) To Nearest Roofline  
3 ft. (91cm)  
Minimum  
Pitched Roof  
Figure 17.1  
10 ft. (305cm) or more  
Less than 10 ft. (305cm)  
Wall or Parapet  
2 ft. (61cm)Minimum  
3 ft. (91cm) Minimum  
3 ft. (91cm) Minimum  
Flat Roof  
Figure 17.2  
Page 17  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
Mobile Home Installation  
6
You must use a Quadra-Fire Outside Air Kit Part  
OAK-ACC and (depending on floor installation, Part  
SRV7033-041) for installation in a mobile home.  
Spark Arestor Cap  
Roof Flashing  
1. An outside air inlet must be provided for combustion See  
page 12 for installation information.  
Storm Collar  
2. Appliance must be secured to the mobile home structure  
by bolting the pedestal through hearth pad and into  
floor.  
ꢀ. Appliance must be grounded with #8 solid copper  
grounding wire or equivalent and terminated at each end  
with N.E.C. approved grounding device.  
Joist Shield/Firestop  
Double wall  
connector pipe  
4. Appliance must be installed with an approved UL10ꢀ HT  
ventilated chimney connector, UL10ꢀ HT chimney, and  
terminal cap with spark arrestor. Never use a single wall  
connector (stove pipe) in a mobile home installation. Use  
only double-wall connector pipe, Dura-Vent DVL, Selkirk  
metalbestos DS or Security DL double-wall connector or  
any listed double-wall connector pipe.  
5. In Canada, this appliance must be connected to a 6 inch  
(152mm) factory-built chimney conforming to CAN/ULC-  
629M, STANDARD FOR FACTORY BUILT CHIMNEYS.  
Outside Air  
Rear Vent  
6. Follow the chimney and chimney connector manufacturer’s  
instructions when installing the flue system for use in a  
mobile home.  
Floor Protector  
7. Maintain clearance to combustibles.  
8. Floor protection requirements must be followed  
precisely.  
Outside Air Floor Vent  
9. Use silicone to create an effective vapor barrier at the  
location where the chimney or other component penetrates  
to the exterior of the structure.  
Figure 18.1  
NOTE: Offsets from the vertical, not exceeding 45°, are  
allowed per Section 905(a) of the Uniform Mechanical Code  
(UMC). Offsets greater than 45° are considered horizontal  
and are also allowed, providing the horizontal run does not  
exceed 75% of the vertical height of the vent. Construction,  
clearance and termination must be in compliance with the  
UMC Table 9C. This installation must also comply with NFPA  
211.  
CAUTION  
Maintain structural integrity of mobile home:  
Floor, wall, ceiling and/or roof.  
Do NOT cut through:  
•
•
•
Floor joist, wall, studs or ceiling trusses.  
Any supporting material that would affect the structural  
integrity.  
NOTE: Top sections of chimney must be removable to allow  
maximum clearance of 1ꢀ.5 feet (411cm) from ground level  
for transportation purposes.  
WARNING  
Asphyxiation Risk.  
10. Burn wood only. Other types of fuels may generate  
poisonous gases (e.g., carbon monoxide).  
11. If unit burns poorly while an exhaust blower is on in  
home, (i.e., range hood), increase combustion air.  
•
Never install in a sleeping room.  
Consumes oxygen in the room.  
12. Installation shall be in accordance with the Manufacturers  
Home & Safety Standard (HUD) CFR ꢀ280, Part 24.  
Page 18  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
Appliance Set-Up  
7
B. Adjusting The Blower Speed Control  
A. Door Handle Assembly  
The blower speed control for this unit is adjusted at the factory,  
and normally does not require further adjustment.  
1. Install washer on door handle shaft.  
2. Slide door handle through door.  
ꢀ. Install second washer(s) as shown in Figure 19.1.  
4. Install key in groove.  
N
OTE: When the speed control is turned clockwise,  
it will click on to high speed. Continue to turn the  
speed control clockwise to decrease the speed. At  
full clockwise, the blower should blow gently, but  
should not stop.  
5. Align groove in latch cam with key; slide latch cam  
over shaft  
1. With the appliance plugged in, turn the speed  
control knob to slow (full clockwise).  
6. Install locknut but do not overtighten, the handle  
needs to move smoothly.  
2. With a small screwdriver, adjust the blower speed  
by turning the adjustment mechanism through the  
hole on the side of the speed control.  
7. Install spring handle turning in a counter-clockwise  
motion to required 2 inch (51mm) clearance loca-  
tion on door handle rod. Figure 19.1.  
ꢀ. Adjust the speed so the blower runs slowly, but  
does not stop. Turn clockwise to slow the blower  
and counterclockwise to increase the speed.  
CAUTION  
•
•
Do NOT overtighten lock nut.  
Door handle needs to move smoothly.  
2 inch (51mm) clearance  
required from bend in door  
handle rod to end of spring  
handle.  
Door Cross Section  
(example)  
Latch Cam  
Locknut  
Spring  
Handle  
Door Handle  
Spacing  
Washers  
Square Key  
Figure 19.1  
WARNING  
HOT. Injury Risk.  
• Maintain clearance between bend of  
door handle rod and spring handle.  
• Spring handle will get hot and may  
cause injury.  
Page 19  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
Operating Instructions  
8
A. Over-Firing Your Appliance  
B. Wood Selection & Storage (Cont’d)  
wood out - about one hour. It is a waste of energy to burn  
unseasoned wood of any kind.  
WARNING  
Dead wood lying on the forest floor should be considered wet,  
and requires full seasoning time. Standing dead wood can  
be considered to be about 2/ꢀ seasoned. To tell if wood is  
dry enough to burn, check the ends of the logs. If there are  
cracks radiating in all directions from the center, it is dry. If  
your wood sizzles in the fire, even though the surface is dry,  
it may not be fully cured.  
Fire Risk  
Do not over-fire.  
Over-firing may ignite creosote or will damage  
the stove and chimney.  
To prevent over-firing your stove, DO NOT:  
•
•
•
•
Use flammable liquids  
Overload with wood  
Burn trash or large amounts of scrap lumber  
Permit too much air to the fire  
Splitting wood before it is stored reduces drying time. Wood  
should be stacked so that both ends of each piece are  
exposed to air, since more drying occurs through the cut ends  
than the sides. This is true even with wood that has been  
split. Store wood under cover, such as in a shed, or covered  
with a tarp, plastic, tar paper, sheets of scrap plywood, etc.,  
as uncovered wood can absorb water from rain or snow,  
delaying the seasoning process.  
1. Symptoms of Over-Firing  
Symptoms of over-firing may include one or more of the  
following:  
• Chimney connector or appliance glowing  
• Roaring, rumbling noises  
C. Burning Process  
In recent years there has been an increasing concern about  
air quality. Much of the blame for poor air quality has been  
placed on the burning of wood for home heating. In order to  
improve the situation, we at Quadra-Fire have developed  
cleaner-burning woodstoves that surpass the requirements  
for emissions established by our governing agencies. These  
woodstoves, like any other appliances, must be properly  
operated in order to insure that they perform the way they are  
designed to perform. Improper operation can turn most any  
wood stove into a smoldering environmental hazard.  
• Loud cracking or banging sounds  
• Metal warping  
• Chimney fire  
2. What To Do if Your Stove is Over-Firing  
• Immediately close the door and air controls to reduce  
air supply to the fire.  
• If you suspect a chimney fire, call the fire department  
and evacuate your house.  
• Contact your local chimney professional and have your  
stove and stove pipe inspected for any damage.  
1. Kindling or First Stage  
It helps to know a little about the actual process of burning in  
order to understand what goes on inside a stove. The first  
stage of burning is called the kindling stage. In this stage, the  
wood is heated to a temperature high enough to evaporate the  
moisture which is present in all wood. The wood will reach  
the boiling point of water (212°F) and will not get any hotter  
until the water is evaporated. This process takes heat from  
the coals and tends to cool the appliance.  
• Do not use your stove until the chimney professional  
informs you it is safe to do so.  
Hearth & Home Technologies WILL NOT warranty stoves  
that exhibit evidence of over-firing. Evidence of over-firing  
includes, but is not limited to:  
• Warped air tube  
• Deteriorated refractory brick retainers  
• Deteriorated baffle and other interior components  
Fire requires three things to burn - fuel, air and heat. So, if  
heat is robbed from the appliance during the drying stage,  
the new load of wood has reduced the chances for a good  
clean burn. For this reason, it is always best to burn dry,  
seasoned firewood. When the wood isn’t dry, you must  
open the air controls and burn at a high burn setting for a  
longer time to start it burning. The heat generated from the  
fire should be warming your home and establishing the flue  
draft, not evaporating the moisture out of wet, unseasoned  
wood, resulting in wasted heat.  
B. Wood Selection & Storage  
Burn only dry seasoned wood. Store wood under cover, out  
of the rain and snow. Dry and well-seasoned wood will not  
only minimize the chance of creosote formation, but will give  
you the most efficient fire. Even dry wood contains at least  
15% moisture by weight, and should be burned hot enough  
to keep the chimney hot for as long as it takes to dry the  
Page 20  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
2. Second Stage  
The second function of the Start-Up Air Control is operation  
of the rear air system. The rear air is used primarily during  
a High Burn Rate. However, in some instances rear air is  
desired during normal operation to help with combustion of  
fuel towards the back of the firebox particularly when burning  
hardwoods. The rear air is controlled independently from the  
ACC system. Slide the Start-UpAir Control between the first  
and third marker as indicated on the label to allow rear air to  
enter the firebox. Figure 21.1.  
The next stage of burning, the secondary stage, is the period  
when the wood gives off flammable gases which burn above  
the fuel with bright flames. During this stage of burning it is  
very important that the flames be maintained and not allowed  
to go out. This will ensure the cleanest possible fire. If the  
flames tend to go out, it is set too low for your burning condi-  
tions. The air control located at the upper right hand corner  
is used to adjust for burn rates. This is called the Burn Rate  
Air Control. Figure 21.1.  
2. Manual Timer Over-Ride  
3. Final Stage  
If you need to shut the ACC system off before it shuts itself  
off after 25 minutes (i.e. overfire situation), reach down to  
the bottom right rear corner and pull the lever toward you.  
Figure 21.2.  
The final stage of burning is the charcoal stage. This occurs  
when the flammable gases have been mostly burned and only  
charcoal remains. This is a naturally clean portion of the burn.  
The coals burn with hot blue flames.  
It is very important to reload your appliance while enough  
lively hot coals remain in order to provide the amount of heat  
needed to dry and rekindle the next load of wood. It is best  
to open the Burn Rate Air and Start-Up Air Controls before  
reloading. This livens up the coalbed and reduces excessive  
emissions (opacity/smoke). Open door slowly so that ash or  
smoke does not exit appliance through opening. You should  
also break up any large chunks and distribute the coals so  
that the new wood is laid on hot coals.  
HIGH  
Burn Rate  
Air Control  
MED  
LOW  
Air quality is important to all of us, and if we choose to use  
wood to heat our homes we should do so responsibly. To do  
this we need to learn to burn our stoves in the cleanest way  
possible. Doing this will allow us to continue using our wood  
stoves for many years to come.  
D. Automatic Combustion Control (ACC)  
Start-Up  
Air Control  
Typically, when you build a fire, you open the air controls fully  
and monitor the fire to prevent it from going into an overfire  
situation and/or burning your wood up too quickly before you  
shut down the air controls to the desired burn rate. With the  
Automatic Combustion Control (ACC) system, you do not  
have to continually monitor the fire. Once you set the ACC  
system it will control the fire for you. Follow the instructions  
below to learn how to operate your stove with ease.  
Figure 21.1  
E. Air Controls  
1. Start-Up Air Control  
The Start-Up Air Control has two primary functions. The  
first function is to activate the Automatic Combustion Control  
system (ACC). This function is performed by sliding the con-  
trol all the way back until it stops at the “HI” indicator on the  
label and then pulling forward to the front of the stove until  
it stops. This activates the ACC system and opens the front  
air channel and allows air to enter the front of the stove for  
approximately 25 minutes. The front air channel gradually  
shuts down until it is completely closed at the end of the 25  
minutes. The fire is now controlled by the air supplied by the  
Burn Rate Air Control. This function should be performed  
each time you reload the stove. Figure 21.1.  
Manual  
Timer (ACC)  
Shut Down  
Pull Forward  
to Shut Down  
Figure 21.2  
Page 21  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
2. Burn Rate Air Control  
4. Medium-Low Burn Rate - 10,000 to 15,000 BTU/hr  
This air supply enters at the upper front of the firebox, near the  
top of the glass door. This preheated air supplies the neces-  
sary fresh oxygen to mix with the unburned gases, helping  
to create second, third and fourth combustions. This air is  
regulated by the Burn RateAir Control. There are four settings  
High, Medium-High, Medium-Low and Low. When the control  
is raised all the way up it is on the High setting and when  
pushed all the down it is on the Low setting. Figure 22.1.  
Raise the Burn Rate Air Control up to the bottom of  
the middle marker and stop. Slide the Start-Up Air  
Control all the way back until it stops (HI marker) and  
then pull forward until it stops. This activates the timer  
system (ACC).  
5. Low Burn Rate - Below 10,000 BTU/hr  
Leave the Burn RateAir Control at the bottom marker.  
Slide the Start-Up Air Control all the way back until it  
stops (HI marker) and then pull forward until it stops.  
This activates the timer system (ACC).  
F. Burn Rates and Operating Efficiency  
For maximum operating efficiency  
HIGH  
1. This appliance has a timer system (ACC) that operates  
the stove at its maximum efficiency removing any guess  
work for the homeowner. Follow the instructions below  
for each burn rate for the Start-Up Air Control and Burn  
Rate Air Control. Figure 22.1.  
Shown with Side  
Shield Removed  
LOW  
2. Burn dry, well-seasoned wood.  
Low (Closed)  
High (Open)  
Burn Rates  
1. Starting a Fire and Reloading  
Open both controls fully by raising the Burn Rate Air  
Control all the way up until it stops and slide the Start-up  
Air Control back until it stops. After loading the stove with  
wood and starting the fire, set both controls to the desired  
setting by following the burn rate instructions below.  
Burn Rate  
ir Control  
A
Front Air Channel  
Operated by Timer  
Timer  
NOTE: These are approximate settings, and will vary with  
type of wood or chimney draft. Due to altitude and other  
environmental circumstances, this operational information is  
a guideline only.  
Start-Up Air  
Control  
Rear Air Channel  
Operates independently  
from Timer  
Timer Manual  
Shut-off  
2. High Burn Rate - Maximum Heat  
Raise the Burn RateAir Control all the way up until it stops  
(top marker) to a fully open position. Slide the Start-UpAir  
Control all the way back until it stops (HI marker) and leave  
it there. This setting over-rides the timer system (ACC) so  
you must monitor the fire closely while in this setting.  
START-UP  
HI  
REAR AIR  
WARNING  
Risk of Fire.  
When set on High Burn Rate and over-riding  
the Automatic Combustion Control system an  
overfire situation can occur and may result in a  
chimney fire.  
“HI” setting  
over-rides  
Timer  
Wide  
Open  
Closed  
After activating the timer (ACC), if the control is placed  
within the rear air section on the label it will allow rear air  
to enter the firebox. This will not interfere with the timer  
gradually closing the front air channel in 25 minutes. If  
control is set on “HI” it over-rides the timer (ACC).  
Overfiring will void the stove warranty.  
3. Medium-High Burn Rate - 15,000 to 30,000 BTU/hr  
Raise the Burn Rate Air Control all the way up until it  
stops (top marker) to a fully open position. Slide the  
Start-Up Air Control all the way back until it stops (HI  
marker) and then pull forward until it stops. This activates  
the timer system (ACC).  
Figure 22.1  
NOTE: Operate appliance on High Burn 15 minutes a  
day to help keep flue/chimney clean.  
Page 22  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
G. Building A Fire  
Baffle Board even with front  
tube & resting on all tubes  
Before lighting your first fire in the stove:  
1. Confirm the baffle is correctly positioned. It should be  
even with the front tube and resting on all tubes. Figure  
23.1.  
Burn Rate  
Air Control  
2. Remove all labels from glass.  
There are many ways to build a fire. The basic principle  
is to light easily-ignitable tinder or paper, which ignites the  
fast burning kindling, which in turn ignites the slow-burning  
firewood. Here is one method that works well:  
Start-Up  
Air  
Control  
1. Open the Burn Rate Air and Start-Up Air Controls fully.  
2. Place several wads of crushed paper on the firebox floor.  
Heating the flue with slightly crumpled newspaper before  
adding kindling keeps smoke to a minimum.  
Ceramic Blanket on Top  
ꢀ. Lay small dry sticks of kindling on top of the paper.  
4. Make sure that no matches or other combustibles are in  
the immediate area of the appliance. Be sure the room  
is adequately ventilated and the flue unobstructed.  
5. Light the paper in the appliance. NEVER light or rekindle  
fire with kerosene, gasoline, or charcoal lighter fluid; the  
results can be fatal.  
6. Once the kindling is burning quickly, add several full-  
length logs ꢀ inches (76mm) or 4 inches (102mm) in  
diameter. Be careful not to smother the fire. Stack the  
pieces of wood carefully; near enough to keep each  
other hot, but far enough away from each other to allow  
adequate air flow between them.  
Tube Channel  
2 pc Baffle Board  
Figure 23.1  
7. Set the Burn Rate Air Control and activate the timer  
system (ACC).  
WARNING  
Fire Risk.  
Do NOT store wood:  
8. When ready to reload, It is best to fully open both the  
Burn Rate Air and Start-up Air Controls before reload-  
ing. This livens up the coalbed and reduces excessive  
emissions (opacity/smoke). Open door slowly so that  
ash or smoke does not exit appliance through opening.  
Large logs burn slowly, holding a fire longer. Small logs  
burn fast and hot, giving quick heat.  
•
Closer than required clearances to com-  
bustibles to appliance  
•
Within space required for loading or ash  
removal.  
Do NOT operate appliance:  
•
•
With appliance door open.  
With ash removal system door open.  
9. As long as there are hot coals, repeating steps 6  
through 8 will maintain a continuous fire throughout the  
season.  
WARNING  
Fire Risk.  
•
•
•
Do NOT burn wet or green wood.  
Store wood in dry location.  
Stack wood so both ends are exposed to air.  
NOTE:  
Wet, unseasoned wood can cause accumulation of  
creosote.  
•
•
Build fire on brick firebox floor.  
Do NOT use grates, andirons or other methods to support  
fuel.  
It will adversely affect emissions.  
Page 2ꢀ  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
H. Correct Baffle & Blanket Placement  
INCORRECT POSITIONS  
WARNING  
Fire Risk  
Firebox damage due to improper baffle place-  
ment is not covered by warranty. Operate the  
wood burning appliance with the baffle in the  
correct position only.  
Not doing so could result in:  
• Reduced efficiency  
• Overheating the chimney  
• Overheating the rear of the firebox  
Ceramic Blanket and Baffle Board are NOT  
in contact with the back of the firebox.  
• Poor performance  
Ensure correct baffle placement and replace baffle com-  
ponents if damaged or missing.  
CORRECT POSITION  
Back of Firebox  
Ceramic Blanket  
Ceramic Blanket is NOT in contact with the  
back of the firebox and NOT even with the  
Baffle Board in the front.  
Back of Firebox  
Ceramic Blanket  
Baffle Board  
Ceramic Blanket and Baffle Board MUST be  
in contact with the back of the firebox and  
even with each other in the front.  
Baffle Board  
Ceramic Blanket is bunched up at the back  
of the firebox and NOT even with the Baffle  
Board in the front.  
Figure 24.1  
Figure 24.2  
Page 24  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
J. Opacity (Smoke)  
I. Blower Operating Instructions  
NOTE: If your Quadra-Fire wood stove is equipped with an  
optional blower, you should follow these guidelines:  
This is the measure of how cleanly your appliance is burn-  
ing. Opacity is measured in percent; 100% opacity is when  
an object is totally obscured by the smoke column from a  
chimney, and 0% opacity means that no smoke column can  
be seen. As you become familiar with your appliance, you  
should periodically check the opacity. This will allow you to  
know how to burn as nearly smoke-free as possible (goal of  
0% opacity).  
1. Initial (cold) start-up and all Burn Settings  
The blower can be plugged in and turned on right away.  
The blower fan is turned on and off by a snap disc.  
When your stove has reached a certain temperature  
the blower will turn on and when your stove has cooled  
down to a certain temperature it will turn off.  
NOTE: The blower can still be left on at all burn rates  
even if you have deactivated the snap disc with the  
manual over-ride knob. See page 13.  
WARNING  
2. The blower is equipped with a speed control. Adjust  
the fan speed by turning the speed control clockwise  
to “Low” or counterclockwise to “High”.  
Fire Risk.  
• Do NOT burn garbage or flammable fluids  
such as gasoline, naptha or engine oil.  
ꢀ. Snap Disc Location  
• Do NOT burn treated wood or wood with salt (driftwood).  
If you find the blower coming on and off at undesirable  
temperatures, relocate the snap disc to another location  
in the designated zone on the back of the appliance.  
Figure 25.1. There is a manual over-ride switch to  
deactivate the snap disc, if necessary. See page 13.  
• May generate carbon monoxide if burn material other  
than wood.  
May result in illness or possible death.  
WARNING  
Fire Risk.  
Keep combustible materials, gasoline  
and other flammable vapors and liquids  
clear of appliance.  
•
•
Do NOT store flammable materials in the appliance’s  
vicinity.  
Do NOT use gasoline, lantern fuel, kerosene, charcoal  
lighter fluid or similar liquids to start or “freshen up” a  
fire in this heater.  
•
•
Keep all such liquids well away from the heater while it  
is in use.  
Combustible materials may ignite.  
Figure 25.1  
Page 25  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
K. Frequently Asked Questions  
ISSUES  
SOLUTIONS  
Odor from appliance  
When first operated, this appliance may release an odor for the first several hours. This is caused by  
the curing of the paint and the burning off of any oils remaining from manufacturing.  
Metallic noise  
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the  
sound produced by a furnace or heating duct. This noise does not affect the operation or longevity of  
the appliance.  
Whirring sound  
If the optional blower has been installed, the blower produces a whirring sound which increases in  
volume as the speed is increased.  
CAUTION  
Odors and vapors released during initial operation.  
•
•
Curing of high temperature paint.  
Open windows for air circulation.  
Odors may be irritating to sensitive individuals.  
Page 26  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
Maintaining & Servicing Your Appliance  
9
A. General Maintenance  
1. Creosote (Chimney) Cleaning  
WARNING  
Fire Risk.  
•
Frequency: Every 2 months during heating season or  
as recommended by a certified chimney  
sweep; more frequently if chimney exceeds  
or is under 14-16 ft. (measured from bottom  
of appliance)  
•
Do not use chimney cleaners or flame colo-  
rants in your appliance.  
Will corrode pipe.  
2. Disposal of Ashes  
•
By: Certified Chimney Sweep  
•
Frequency: When ash is within 1-ꢀ/4 in. (44mm) of  
firebox lip  
By: Homeowner  
Remove all ash from the firebox and extinguish all hot  
embers before disposal. Allow the appliance to cool  
completely. Disconnect flue pipe or remove baffle and  
ceramic blanket from appliance before cleaning chimney.  
Otherwise residue can pile up on top of the baffle and  
ceramic blanket and the appliance will not work properly.  
(See Baffle Removal on page 34). Close the door tightly.  
The creosote or soot should be removed with a brush  
specifically designed for the type of chimney in use. Clean  
out fallen ashes from the firebox.  
•
Ashes should be placed in a metal container with a  
tight fitting lid. The closed container of ashes should  
be placed on a non-combustible floor or on the ground,  
well away from all combustible materials, pending final  
disposal. If the ashes are disposed of by burial in soil  
or otherwise locally dispersed, they should be retained  
in the closed container until all cinders have thoroughly  
It is also recommended that before each heating season  
the entire system be professionally inspected, cleaned and  
repaired if necessary.  
WARNING  
Fire Risk.  
Inspection: Inspect the system at the appliance connection  
and at the chimney top. Cooler surfaces tend to build  
creosote deposits quicker, so it is important to check the  
chimney from the top as well as from the bottom.  
Disposal of Ashes  
•
•
•
Ashes should be placed in metal container with tight  
fitting lid.  
Do not place metal container on combustible  
surface.  
Ashes should be retained in closed container until all  
cinders have thoroughly cooled.  
Formation and Need For Removal: When wood is burned  
slowly, it produces tar and other organic vapors which  
combine with expelled moisture to form creosote. The  
creosote vapors condense in the relatively cool chimney  
flue of a newly-started or a slow-burning fire. As a result,  
creosote residue accumulates on the flue lining. When  
ignited, this creosote creates an extremely hot fire which  
may damage the chimney or even destroy the house. The  
chimney connector and chimney should be inspected once  
every 2 months during the heating season to determine if a  
creosote or soot buildup has occurred. If creosote or soot  
has accumulated, it should be removed to reduce the risk  
of a chimney fire.  
3. Glass Cleaning  
•
•
Frequency: As desired  
By: Homeowner  
Clean glass with a non-abrasive glass cleaner. Abrasive  
cleaners may scratch and cause glass to crack. If the  
deposits on the glass are not very heavy, normal glass  
cleaners work well. Heavier deposits may be removed  
by using a damp cloth dipped in wood ashes or by using  
a commercially available oven cleaner. After using an  
oven cleaner, it is advisable to remove any residue with  
a glass cleaner or soap and water. Oven cleaner left on  
during the next firing can permanently stain the glass  
and damage the finish on plated metal surfaces.  
WARNING  
Fire Risk.  
Prevent creosote buildup.  
Inspect chimney connector and chimney once  
every two months during heating season.  
Aportion of the combustion air entering the firebox is deflected  
down over the inside of the door glass. This air flow “washes”  
the glass, helping to keep smoke from adhering to its surface.  
When operated at a low burn rate, less air will be flowing  
over the glass and the smokey, relatively cool condition of a  
low fire will cause the glass to become coated. Operating  
the appliance with the Burn Rate Air Control and Start-Up Air  
Control all the way open for 15-20 minutes should remove  
the built up coating.  
• Remove creosote to reduce risk of chimney fire.  
• Ignited creosote is extremely HOT.  
Page 27  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
CAUTION  
WARNING  
Handle glass with care.  
Handle glass assembly with care.  
•
Inspect the gasket to ensure it is  
undamaged.  
Glass  
Assembly  
Glass  
When cleaning glass:  
Assembly  
•
Avoid striking, scratching or  
slamming glass.  
•
•
Do NOT strike, slam or scratch glass.  
Do NOT operate appliance with glass  
& door assembly removed.  
•
Do NOT clean glass when hot.  
•
•
•
•
Do NOT use abrasive cleaners.  
•
Do NOT operate with glass cracked, broken or scratched.  
Use a hard water deposit glass cleaner on white film.  
Use commerical oven cleaner on heavier deposits.  
Remove all residue of oven cleaner or will permanently  
stain glass on next firing.  
•
Refer to maintenance instructions.  
WARNING  
Fire Risk.  
Injury Risk.  
B. Glass Replacement  
•
•
Use only glass specified in manual.  
DO NOT REPLACE with any other material.  
1. Ensure that the fire is out and the appliance is cool to  
the touch.  
Glass breakage will occur.  
2. Protect a table or counter top with padding or towels.  
Protect your hands and wear gloves to prevent injury.  
ꢀ. Remove the door with the broken glass by lifting the  
door up and off of the hinges.  
4. Lay door face down on a table or counter making sure  
the handle hangs over the edge so the door lays flat, on  
a soft surface.  
5. Remove the screws from each glass retainer and remove  
the glass. (If screws are difficult to remove, soak with  
penetrating oil first).  
6. Center the glass with edges evenly overlapping the  
opening in the door, (i.e. same space top and bottom,  
left and right sides).  
7. Replace the glass retainers. Be careful not to cross  
thread the screws.  
8. Tighten each retainer just a few turns until each is  
secured. Check again for centering of glass in door  
frame. Continue to tighten each retainer alternately, a  
few turns at a time, until the glass is secure. DO NOT  
OVERTIGHTEN.  
9. Replace the door on the appliance.  
Quadra-Fire stoves are equipped with ceramic super heat-  
resistant glass, which can only be broken by impact or  
misuse. Do not slam stove door or impact the glass. When  
closing door, make sure that logs do not protrude against the  
glass. Inspect glass regularly. If you find a crack or break,  
immediately put the fire out and return the door to your dealer  
for replacement of glass before further use.  
Page 28  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
C. Firebrick Replacement  
Replace the firebrick if they become crumbly and/or if  
there is a 1/4 inch (6.ꢀ5mm) gap between the bricks.  
3
3
Inspect the firebrick after each ash removal.  
1
1
The firebox is lined with high quality firebrick, which has  
exceptional insulating properties. There is no need to  
use a grate; simply build a fire on the firebox floor. Do  
not operate appliance without firebrick.  
1
1
1
1
1
1. After the coals have completely cooled, remove all  
old brick and ash from unit and vacuum firebox.  
1
1
2
2
5
2
4
2. Remove new brick set from box and lay out to  
diagram shown.  
ꢀ. Lay bottom bricks in unit.  
4. Install rear bricks on the top of the bottom bricks.  
Slide top of bricks under clip on back of firebox wall  
and push bottom of brick back.  
8-1/2 inches (216mm)  
5. Install side bricks. Slide top of brick under clips  
on side of firebox and push the bottom of the brick  
until it is flush with the side of the unit.  
1-3/8 in.  
(35mm)  
4
1-3/4 in.  
(44mm)  
Use Part 8ꢀ2-0550 when ordering individual brick. Provide brick  
dimension or copy this page, mark the desired brick and take it  
to your authorized dealer.  
6-1/4 inches  
(159mm)  
7 inches (178mm)  
3 inches  
(76mm)  
5
8-1/2 inches (216mm)  
Figure 29.1  
No.  
1
Brick Size  
Qty  
9
9 x 4-1/2 x 1-1/4  
6 x 4-1/2  
2
3
3
8 x 4-1/2 x 1-1/4  
2
4
Brick with angle (see drawing)  
Brick with angle (see drawing)  
1
5
1
Page 29  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
D. Baffle Removal  
E. Snap Disc Replacement  
1. Locate the snap disc bracket assembly at the bottom left  
1. Remove all ash from the firebox, and extinguish all hot  
embers before disposal into a metal container.  
rear corner of the stove. Figure 30. 3.  
2. A magnet holds the bracket to the stove. Pull the bracket  
down away from the stove to expose the snap disc.  
2. The baffle board has 2 pieces. With the ceramic blanket  
still in place, slide one baffle piece over the top of other one  
and pull out top piece through the door opening and then  
remove bottom baffle piece. Figure 30.1.  
ꢀ. Pull the snap disc and spade connectors up and out of  
bracket as shown in Figure 30.4.  
ꢀ. Remove the ceramic blanket.  
4. Using a Phillips head screw driver, remove the 2 screws  
from the snap disc and then remove the snap disc from  
the spade connectors. Replace with new snap disc and  
re-connect to spade connectors.  
4. Re-install the baffle pieces one piece at a time. Be sure  
the baffle boards are even with the front manifold tube and  
is resting on all tubes. Figure 23.1 on page 23. See Also  
Correct Blanket & Baffle Position on page 24.  
5. Push the snap disc and spade connectors back inside  
bracket and re-attach the bracket to the stove.  
5. To re-install the ceramic blanket, it is easier to fold it in half  
first. Figure 30.2. Place on top of baffle board, open up  
and flatten and smooth out the blanket. Re-check the baffle  
board for correct positioning. Figure 23.1 on page 23 and  
page 24.  
Snap Disc Location  
Figure 30.1 - Baffle  
Figure 30.3  
Snap Disc  
Magnet  
Spade  
Connectors  
30.2 - Ceramic Blanket  
Figure 30.4  
Page ꢀ0  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
F. Tube Channel Assembly Replacement  
NOTE: Service Space  
In order to replace the tube channel assembly a clear-  
ance of 17 inches (4ꢀ2mm) is required on the right side  
of stove in order to remove the tubes with the stove in  
place.  
Removing Tube Channel Assembly  
1. Remove the right side shield by removing 2 screws in the  
back using a Phillips head screw driver.  
2. Remove 4 screws from channel access cover and remove  
cover.  
If space is not available, the stove will have to be dis-  
connected from the chimney to proceed with the tube  
replacement.  
ꢀ. Locate 2 channel nuts inside of chamber and remove  
using a 7/16 socket wrench. Slide out tube channel  
assembly.  
NOTE:Soak the bolts with penetrating oil for at least 15 min-  
utes before trying to remove them.  
Replacing Tube Channel Assembly  
1. Slide one gasket on each tube first  
2. Slide the tube channel assembly into side of firebox and  
insert each tube into the corresponding hole in the tube  
channel rack starting with the back hole first.  
ꢀ. Make sure tube channel assembly is flush against the  
side of the stove and secure with channel nuts.  
4. Re-install channel cover and side shield.  
Slide one gasket  
over each tube  
Channel  
Tube Channel Rack  
Channel Cover  
Screws (4)  
Access  
Cover  
Remove  
2 Screws  
Channel  
Nuts (2)  
Tube Channel  
Assembly  
Side Panel  
Figure 31.1  
Page ꢀ1  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
With proper installation, operation, and maintenance your woodstove  
will provide years of trouble-free service. If you do experience a prob-  
lem, this troubleshooting guide will assist a qualified service person in  
the diagnosis of a problem and the corrective action to be taken.  
Troubleshooting  
10  
Start Fire Problems  
Possible Cause  
Solution  
Can’t get fire started  
Excessive smoke or spillage  
Burns too slowly  
Not enough kindling/paper or no  
Use dry kindling, more paper. Arrange kindling & wood  
for air movement.  
kindling/paper  
Not enough air for fire to ignite  
Check for restricted cap/shroud  
Open outside air kit (if installed).  
Check for flue blockage.  
Smolders, sizzles  
Pre-warm flue before starting fire (refer to starting fire  
section).  
Check for adequate vent height (refer to chimney  
assembly section).  
Open window below the appliance towards the wind.  
Wood condition is too wet, too large  
Use dry, seasoned wood (refer to wood fuel section).  
Bed of coals not established before  
adding wood  
Start with paper & kindling to establish bed of coals (refer  
to starting fire section).  
Flue blockage such as birds’ nests or  
leaves in termination cap  
Have chimney inspected for creosote and cleaned by a  
certified chimney sweep.  
Down draft or negative pressure  
Competition with exhaust devices  
Do not use exhaust fans during start-up (refer to negative  
pressure section).  
Open window below the appliance towards the wind.  
Fire burns too fast  
Extremely dry or soft wood  
Overdrafting  
Mix in hardwood.  
Mix in less seasoned wood after fire is established (refer  
to wood fuel section).  
Check for correct vent height; too much vertical height  
creates overdrafting.  
Check location of vent termination (refer to chimney  
requirements section).  
Page ꢀ2  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
Reference Materials  
11  
A. Exploded Drawings  
Item  
ꢀ2  
Description  
Door, Cast  
Part No.  
not sold sep.  
41  
33  
Spring Handle, 1/2 inch  
Gold: 8ꢀ2-0620  
Nickel: 250-8ꢀꢀ0  
34  
35  
Door Handle Rod  
Washer, Spacing  
430-1131  
40  
(Qty ꢀ) 8ꢀ2-0990  
(Qty 1) 222-0010  
36  
37  
ꢀ8  
39  
40  
41  
Glass Replacement  
Key, Cam Latch  
Cam Latch  
7000-013  
430-1151  
430-1141  
8ꢀ2-1060  
GL-FRM-21M  
42  
Nut, Locking  
39  
38  
37  
Glass Frame Assy (set)  
Screws,Glass Frame (10) (Qty 10) 8ꢀ2-0860  
(Qty 1) 220-0490  
36  
42  
Hinge Pins  
Gold: 8ꢀ2-0250  
Nickel: 4ꢀ0-5ꢀ20  
32  
35  
34  
33  
Glass Size: 14-1/8” wide x 9-1ꢀ/16” high  
Figure 33.1 - Door, Glass And Door Handle Assembly  
Item  
Description  
Part No.  
7000-343  
229-06ꢀ1  
70ꢀꢀ-210  
10  
12  
4
5
6
Knob, Start-Up Air Control  
Magnet for Air Control  
13  
Air Control Rod Guide,  
Start-Up  
7
9
Control Arm Assy, Rear Air  
SRV70ꢀ9-006  
9
14  
Timer, Mechanical, Replacement SRV480-1940  
Timer Arm Assembly 7033-034  
10  
12  
Gasket, Front & Rear Air Timer 70ꢀꢀ-282  
Doors  
13  
14  
Burn Rate Air Control Assembly 7037-004  
7
Spring Handle, 1/4 inch  
Gold: 8ꢀ2-06ꢀ0  
Nickel: 250-8ꢀ40  
6
Snap Disc, F125 F-20  
2ꢀ0-0470  
49  
49  
Timer Air Control Assembly  
SRV70ꢀ9-015  
4
5
Figure 33.2 - Burn Rate Air & Start-Up Air Controls  
Page ꢀꢀ  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
25  
21  
24  
22  
23  
12  
10  
13  
27  
14  
26  
9
20  
28  
19  
29  
30  
7
43  
6
18  
17  
4
31  
5
3
16  
2
1
SIZES  
(#ꢀ0) Baffle Board: 8-1/8” w x 1ꢀ” h, each  
(#29) Ceramic Blanket: 19” w x 1ꢀ-ꢀ/4” h, 1/2” thick  
Figure 34.1  
Item  
1
Description  
Oak Strip for Pedestal  
Pedestal Base  
Item  
Description  
18  
19  
20  
21  
22  
2ꢀ  
24  
25  
26  
27  
28  
29  
30  
31  
43  
Panel Assembly, Side, Right  
2
Tube Channel Access Cover (Top)  
Tube Channel Assembly  
Air Channel, Convection  
Bracket, Convection Mount  
Air Supply, Back  
3
Pedestal Riser  
4
Knob, Start-Up Air Control  
Magnet  
5
6
Air Control Rod Guide, Start-Up  
Control Arm Assembly, Rear Air  
Timer, Mechanical  
7
Flue Collar  
9
Panel Assembly, Side, Left  
Air Channel Assembly, Rear  
Brick, Set  
10  
12  
13  
14  
16  
17  
Timer Arm Assembly  
Gasket, Front & Rear Air Doors  
Burn Rate Air Control Assembly  
Spring Handle, 1/4 inch  
Label for Burn Rate Air Control  
Label for Start-Up Air Control  
Tube Support Rack  
Blanket, Ceramic  
Baffle Fiberboard, (2 pc)  
Brick Retainer  
Timer Air Control Assembly  
Page ꢀ4  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
B. Service Parts & Accessories  
IMPORTANT: THIS IS DATED INFORMATION. When requesting a part for your appliance, please  
supply serial number and model name/number to ensure correct service parts. All parts may be order  
from an authorized dealer.  
ITEM #  
ACCESSORIES  
PART NO.  
Blower Assembly  
BK-ACC  
31  
Door Assembly, Black  
SRV70ꢀ9-008  
OAK-ACC  
Outside Air Kit, Floor & Rear (termination cap, wire ties, flex adapter, fasteners)  
see page 12 Outside Air Back Cover Plate & Sealing Rope, (1 inch x 4 ft) Floor Only  
SRV70ꢀꢀ-041  
UK-DRNL  
Upgrade to Nickel Door (includes Nickel Spring Handles (1) 1/2 inch and (2) 1/4  
inch, (2) Nickel Hinge Pins and Nickel Quadra-Fire Logo  
ITEM #  
SERVICE PARTS  
PART NO.  
SRV70ꢀ9-107  
70ꢀꢀ-210  
21  
Air Channel, Convection  
Air Control Rod Guide, Start-Up Air  
Baffle, Fiberboard (2 pieces) 8-1/8 in. wide x 1ꢀ in. high  
Blower (Motor Only) Replacement  
Blanket, Ceramic 1/2 in. thick, field cut to size, 16-ꢀ/8 in. wide x 1ꢀ in. high  
Brick, Individual  
30  
SRV70ꢀ9-111  
812-4900  
29  
8ꢀ2-ꢀꢀ90  
8ꢀ2-0550  
31  
Brick Retainer  
7033-149  
27  
Brick, Set  
SRV70ꢀ9-007  
8ꢀ2-ꢀ040  
Brick, Uncut, (Set of 6)  
13  
Burn Rate Air Control Assembly  
Cam Latch (Door Handle)  
7037-004  
ꢀ8  
430-1141  
Component Pack, (includes Touch-up Paint, Gold Spring Handles (1) 1/2 inch and  
(2) 1/4 inch, Trimount Plug, Owner’s Manual and Warranty Card  
7039-011  
Component Pack for Nickel Door (includes Nickel Spring Handles (1) 1/2 inch and  
(2) 1/4 inch, (2) Nickel Hinge Pins and Nickel Quadra-Fire Logo  
436-5360  
7
Control Arm Assembly, Rear Air  
Door Handle Assembly  
SRV70ꢀ9-006  
8ꢀ2-0540  
430-1131  
SRV7000-ꢀ02  
8ꢀ2-1680  
8ꢀ2-0460  
70ꢀꢀ-282  
7000-013  
GL-FRM-21M  
8ꢀ2-0250  
430-1151  
7000-343  
7033-160  
7033-166  
200-ꢀ180  
200-ꢀ240  
229-06ꢀ1  
34  
Door Handle Rod Only  
24  
Flue Collar  
Gasket (Rope) Door, ꢀ/4 inch x 7 ft, field cut to size  
Gasket, (Tape) Glass, 5 ft  
Gasket, Front & Rear Air Timer Doors  
Glass Assembly  
12  
36  
40  
42  
37  
4
Glass Frame, Set (4 pc)  
Hinge Pins, Gold (2)  
Key, Cam Latch, (Door Handle)  
Knob, Start-Up Air Control  
Label for Burn Rate Air Control  
Label for Start-Up Air Control  
Logo, Quadra-Fire, Gold  
Logo, Quadra-Fire, Nickel  
Magnet for Air Control  
16  
17  
5
Page ꢀ5  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
ITEM #  
SERVICE PARTS  
PART NO.  
39  
Nut, Locking (Door Handle)  
8ꢀ2-1060  
see page 12 Outside Air Cover Plate & Sealing Rope, 1 inch x 4 ft  
Paint, Touch-Up, Matte Black  
SRV70ꢀꢀ-041  
7000-304  
25  
18  
2
Panel Assembly, Side, Left  
Panel Assembly, Side, Right  
Pedestal Base  
SRV70ꢀ9-00ꢀ  
SRV70ꢀ9-002  
7033-163  
3
Pedestal Riser  
70ꢀꢀ-207  
26  
Rear Air Channel Assembly  
Rivnut Repair Kit  
SRV70ꢀ9-001  
RIVNUT-REPAIR  
41  
Screws, Glass Frame, tabs are not required  
Qty 10: 8ꢀ2-0860  
Qty 1: 200-0490  
Snap Disc, F125 F-20  
2ꢀ0-0470  
Speed Control Only  
842-0ꢀ70  
14  
14  
33  
33  
43  
10  
9
Spring Handle, Burn Rate Control, 1/4 inch, Gold  
Spring Handle, Burn Rate Control, 1/4 inch, Nickel  
Spring Handle, Door, 1/2 inch, Gold  
Spring Handle, Door, 1/2 inch, Nickel  
Timer Air Control Assembly  
8ꢀ2-06ꢀ0  
250-8ꢀ40  
8ꢀ2-0620  
250-8ꢀꢀ0  
SRV70ꢀ9-015  
7033-034  
Timer Arm Assembly  
Timer, Mechancial, Replacement  
Trim, Oak Strips for Pedestal (2)  
Tube Channel Access Cover (Top)  
Tube Channel Assembly (Manifold Tubes)  
Tube Support Rack  
SRV480-1940  
8ꢀ2-0560  
1
19  
20  
28  
35  
SRV70ꢀ9-114  
SRV70ꢀ9-004  
SRV70ꢀ9-108  
Washers, Spacing, Door Handle  
Qty ꢀ: 8ꢀ2-0990  
Qty 1: 222-0010  
Wire Harness for Blower & Snap Disc  
70ꢀꢀ-262  
Page ꢀ6  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
C. Service And Maintenance Log  
Date of Service  
Performed By  
Description of Service  
Page ꢀ7  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
C. Service And Maintenance Log (Cont’d)  
Date of Service  
Performed By  
Description of Service  
Page ꢀ8  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
D. Homeowner’s Notes  
Page ꢀ9  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
D. Homeowner’s Notes (Cont’d)  
Page 40  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
E. Warranty Policy  
Hearth & Home Technologies LIMITED WARRANTY  
Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood,  
pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or  
Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.  
Warranty Period  
Parts Labor  
HHT Manufactured Appliances and Venting  
EPA  
Components Covered  
Gas  
Wood  
Pellet  
Electric  
Venting  
Wood  
All Parts and Material Except  
as covered by Conditions,  
Exclusion, and Limitations  
listed  
1 Year  
X
X
X
X
X
X
Igniters, Electronic Compo-  
nents, and Glass  
Blowers  
X
X
X
X
2 years  
ꢀ years  
X
X
X
Molded Refractory Panels  
X
X
Firepots  
5 years  
ꢀ years  
ꢀ years  
X
X
Castings & Baffles  
Firebox, HHT Chimney, Ter-  
mination & Heat Exchanger  
7 years  
X
X
X
X
10  
1 year  
1 year  
X
years  
Burners, Logs & Refractory  
Limited  
Lifetime  
X
X
Firebox & Heat Exchanger  
All Replacement Parts  
90 Days  
X
X
X
See Conditions, Exclusions, and limitations.  
9-01-08  
CONDITIONS, ExCLUSIONS & LIMITATION OF LIABILITY  
.
This warranty applies to the original owner and is transferable up to two years from date of purchase to the new  
homeowner, provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance  
remains in its original place of installation.  
.
.
.
The maximum amount recoverable under this warranty is limited to the purchase price of the product.  
In no event shall HHT be liable for any incidental or consequential damages caused by defects in the product.  
Adjustments, regular maintenance, cleaning and temporary repairs, or the failure to duplicate the problem in the home  
is not covered under this warranty.  
.
This limited warranty does not extend to or include surface finish on the appliance or terminations, door gasketing,  
glass gasketing, glass discoloration, firebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or  
corrosion on any of the metal surfaces, cast iron components, baffles, firepots, doors, or firebox area are not covered  
by this warranty.  
.
Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to  
this noise are not covered by this warranty.  
4021-645A 09-01-08  
Page 41  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
Hearth & Home Technologies LIMITED WARRANTY (Cont’d)  
.
HHT’s obligation under this warranty does not extend to damages resulting from: (1) installation, operation or  
maintenance of the appliance not in accordance with the installation instructions; operating instructions and the  
listing agent identification label furnished with the appliance; (2) installation which does not comply with local build-  
ing codes; (ꢀ) shipping, improper handling, improper operation, abuse, misuse, accident or unworkmanlike repairs;  
(4) environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure  
or handling devices such as exhaust fans or forced air furnaces or other such causes; (5) use of fuels other than  
those specified in the operating instructions; (6) installation or use of components not supplied with the appliance or  
any other components not expressly authorized and approved by HHT; and/or (7) modification of the appliance not  
expressly authorized and approved by HHT in writing.  
.
.
This warranty does not apply to non-HHT venting components, hearth components or other accessories used in con-  
junction with the installation of this product.  
This warranty is void if the appliance has been over-fired or operated in atmospheres contaminated by chlorine,  
fluorine, or other damaging chemicals the appliance is subject to prolonged periods of dampness or condensation, or  
there is any damage to the appliance or other components due to water or weather damage which is the result of, but  
not limited to, improper chimney or venting installation.  
.
.
.
HHT’s liability under this warranty is limited to the replacement and repair of defective components or workmanship  
during the applicable period. HHT may fully discharge all of its obligations under such warranties by repairing the  
defective component(s) at HHT’s discretion. Shipping costs are not covered under this warranty.  
Some states do not allow exclusions or limitation of incidental or consequential damages, so those limitations may  
not apply to you. This warranty gives you specific rights; you may also have other rights, which vary from state to  
state.  
EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE  
WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION  
OF THE WARRANTY SPECIFIED ABOVE.  
This Limited Warranty is effective on all HHT appliances sold after September 01, 2008 and supersedes any and all war-  
ranties currently in existence.  
If warranty service is needed, you should contact your installing dealer. If the installing dealer is unable to provide neces-  
sary parts or components, contact the nearest authorized HHT dealer or supplier.  
4021-645A 09-01-08  
Page 42  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
2100 Millennium Wood Stove (ACC)  
This page is left blank intentionally  
Page 4ꢀ  
September 1, 2008  
7039-131F  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
CONTACT INFORMATION:  
Hearth & Home Technologies  
1445 North Highway  
Colville, WA 99114  
Division of HNI INDUSTRIES  
Please contact your Quadra-Fire dealer with any questions or concerns.  
For the number of your nearest Quadra-Fire dealer,  
visit our web site at www.quadrafire.com  
CAUTION  
Do NOT discard this manual.  
•
•
•
Important operating and maintenance  
instructions included.  
Read, understand and follow these instruc-  
tions for safe installation and operation.  
Leave this manual with party responsible  
for use and operation.  
We recommend that you record the following pertinent  
information for your 2100 MILLENNIUM WOOD STOVE (ACC)  
Date purchased/installed:  
Serial Number:  
Location on appliance:  
Dealership purchased from:  
Notes:  
Dealer phone:  
This product may be covered by one or more of the following patents: (United States) 459ꢀ510, 4686807, 4766876, 479ꢀꢀ22, 48115ꢀ4,  
5000162, 5016609, 5076254, 511ꢀ84ꢀ, 5191877, 521895ꢀ, 526ꢀ471, 5ꢀ28ꢀ56, 5ꢀ41794, 5ꢀ4798ꢀ, 5429495, 5452708, 5542407,  
560107ꢀ, 561ꢀ487, 5647ꢀ40, 5688568, 5762062, 5775408, 5890485, 59ꢀ1661, 59412ꢀ7, 5947112, 5996575, 600674ꢀ, 6019099,  
6048195, 605ꢀ165, 6145502, 6170481, 62ꢀ7588, 6296474, 6ꢀ74822, 641ꢀ079, 64ꢀ9226, 6484712, 654ꢀ698, 6550687, 6601579,  
6672860, 6688ꢀ02B2, 6715724B2, 6729551, 67ꢀ61ꢀꢀ, 6748940, 6748942, 6769426, 6774802, 6796ꢀ02, 6840261, 6848441, 686ꢀ064,  
6866205, 6869278, 6875012, 6880275, 69080ꢀ9, 6919884, Dꢀ20652, D445174, D4624ꢀ6; (Canada) 1297749, 2195264, 2225408,  
2ꢀ1ꢀ972; (Australia) 780250, 78040ꢀ, 1418504 or other U.S. and foreign patents pending.  
Page 44  
7039-131F  
September 1, 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Grizzly Sander G1140 User Manual
Harbor Freight Tools Bicycle Accessories 91212 User Manual
Harbor Freight Tools Home Security System 95811 User Manual
Hasbro Games Go Along User Manual
Hawking Technology Switch CS152F User Manual
Hayter Mowers Lawn Mower SST38 ST42 User Manual
HP Hewlett Packard Switch 498358B21 User Manual
HTC Cell Phone Touch Cruise User Manual
Husqvarna Chainsaw 61 268 User Manual
Husqvarna Tiller DRT900E User Manual