Model No. HRTL34306.1
Serial No.
USER'S MANUAL
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-922-4222
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
of this manual and order part number 146148,
or see your local electronics store.
12. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
which may result in a fall and serious injury.
protect the floor or carpet from damage, place 13. Keep the power cord and the surge suppres-
a mat under the treadmill.
sor away from heated surfaces.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See MAIN-
TENANCE AND TROUBLESHOOTING on page
18 if the treadmill is not working properly.)
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 12).
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 250 pounds.
16. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
8. Never allow more than one person on the
treadmill at a time.
17. The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The pulse sensor is intended only as an exer-
cise aid in determining heart rate trends in
general.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes; never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
10. When connecting the power cord (see page 11),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
19. Never leave the treadmill unattended while it is
running. Always remove the key and unplug
the power cord when the treadmill is not in use.
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6 and HOW TO FOLD
AND MOVE THE TREADMILL on page 16.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 11. To purchase a surge suppressor, see
your local HEALTHRIDER dealer or call the
toll-free telephone number on the front cover
3
Download from Www.Somanuals.com. All Manuals Search And Download.
21. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
22. Do not change the incline of the treadmill by
placing objects under the treadmill.
23. Inspect and properly tighten all parts of the
treadmill regularly.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in any commer-
cial, rental, or institutional setting.
24. Never drop or insert any object into any
opening on the treadmill.
25.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here has been placed on the treadmill.
If a decal is missing, or if it is not legible, call the toll-free
telephone number on the front cover of this manual and
order a free replacement decal. Apply the decal in the lo-
cation shown. Note: The decals are not shown at actual
size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the HEALTHRIDER® H110i
treadmill. The H110i treadmill combines advanced
technology with innovative design to let you enjoy an
excellent form of cardiovascular exercise in the conve-
nience and privacy of your home. And when you’re not
exercising, the unique H110i treadmill can be folded
up, requiring less than half the floor space of other
treadmills.
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number is found on the front cover of this man-
ual. The serial number is found on a decal attached to
the treadmill (see the front cover of this manual for the
location of the decal).
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
you use the treadmill. If you have questions after
Accessory Tray
Handrail
Console
Key/Clip
Storage Latch
Hood
Walking Belt
Reset/Off
Circuit Breaker
Power Cord
Wheel
Foot Rail
Rear Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to
the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant
on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
In addition to the included hex keys
, assembly requires a phillips screwdriver
, an
adjustable wrench , and needlenose pliers
.
Use the drawings below to identify the hardware used during assembly. Note: If a part is not in the parts bag,
check to see if it has been preattached to one of the parts to be assembled. Extra hardware may be in-
cluded. To avoid damaging plastic parts, do not use power tools for assembly.
Crossbar Screw
(85)–2
Console Screw/
Latch Screw (10)–6
Silver Ground
Screw (84)–1
Base Pad
Screw (26)–6
Handrail Bolt (8)–4
Crossbar Star
Washer (7)–2
Wheel Housing Bolt (13)–4
Handrail Star
Washer (5)–4
Upright Washer
(14)–2
Upright Bolt (2)–4
Upright Nut(75)–4
Upright Star
Washer (9)–6
Wheel Housing
Washer (32)–4
Wheel Housing
Nut (43)–4
Colored Patch Frame Bolt (1)–2
1. Make sure that the power cord is unplugged.
1
26
63
Have a second person hold the Base (52) in the
position shown.
26
26
63
63
Attach six Base Pads (63) to the Base (52) with
six Base Pad Screws (26).
52
26
63
26
63
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Have a second person hold the Base (52) in the
position shown.
2
Identify the Left Upright (53) (the Right Upright [54]
has a large hole near the lower end).
9
2
75
Hold the Left Upright (53) so the two small
holes are on top as shown. Insert two Upright
Bolts (2) into the bracket on the Left Upright.
Attach the Left Upright to the Base (52) with the
Upright Bolts, two Upright Star Washers (9) and
two Upright Nuts (75). Do not tighten the
Upright Nuts yet.
54
9
9
2
Large
Hole
52
75
Small Holes
9
Attach the Right Upright (54) to the Base (52) in
the same way.
53
3. Slide the two Wheel Housings (45) onto the Base
(52). Attach each Wheel Housing with two Wheel
Housing Bolts (13), two Wheel Housing Washers
(32), and two Wheel Housing Nuts (43).
3
32
45
13
43
32
32
32
45
43
13
52
4. Position the Base (52) as close to the front of the
treadmill as possible, as shown.
4
4a
39
39
54
See drawing 4a. Insert the wire tie and the con-
nector on the end of the Wire Harness (39) into
the square hole in the Right Upright (54). Then,
insert the Wire Harness until the wire tie is ex-
tending from the upper end of the Right Upright.
Secure the Wire Harness to the top of the Right
Upright so that it will not fall inside.
Wire Tie
54
52
4b
See drawing 4b. Attach the ground wire on the
Wire Harness (39) to the indicated hole in the
Base (52) with a Silver Ground Screw (84).
Then, press the indicated Grommet (49) into the
Right Upright (54).
54
49
39
Ground
Wire
84
52
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. See the left inset drawing. Identify the two Frame
Spacers (11). Open the included packet of
grease, and apply grease to both sides of both
Frame Spacers. Then, identify the outer side of
each Frame Spacer.
5
54
Hold a Frame Spacer (11) between the Right
Upright (54) and the Lift Frame (104), with the
outer side of the Frame Spacer facing the
Right Upright. Attach the Right Upright to the
Lift Frame with a Colored Patch Frame Bolt (1),
an Upright Washer (14), and an Upright Star
Washer (9); do not tighten the Colored Patch
Frame Bolt yet.
9
1
14
11
104
11
Inner
Side
54
14
1
11
104
Outer
Side
9
6. See the left inset drawing. Identify the outer side
of the remaining Frame Spacer (11).
6
53
Hold the Frame Spacer (11) between the Left
Upright (53) and the Lift Frame (104), with the
outer side of the Frame Spacer facing the
Left Upright. Attach the Left Upright to the Lift
Frame with a Colored Patch Frame Bolt (1), an
Upright Washer (14), and an Upright Star
Washer (9); do not tighten the Colored Patch
Frame Bolt yet.
9
14
11
1
104
11
Inner
Side
53
14
1
11
Outer
Side
104
9
8
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Set the Console Assembly (91) face-down on a
soft surface to avoid scratching the Console
Assembly. Hold the Right Handrail (33), which
has a large hole in the location shown, near the
Console.
7
Console
Wire
85
7
10
Bracket
Next, insert the console wire into the hole in the
side of the Right Handrail (33). Using
needlenose pliers, pull the console wire out of
the hole near the bracket on the Right Handrail.
Large
Hole
33
Then, set the Right Handrail (33) on the Console
Assembly (91). Make sure that no wires are
pinched. Finger tighten a Crossbar Screw (85)
with a Crossbar Star Washer (7) into the Right
Handrail, and then start two Console Screws
(10) into the Right Handrail. Tighten the
91
Crossbar Screw and then the two Console
Screws; do not overtighten the Screws.
Attach the Left Handrail (not shown) to the
Console Assembly (91) in the same way. Note:
There are no wires on the left side.
8. See drawing 8a. Press the indicated tab and re-
move the guard from the console wire with
needlenose pliers. Discard the guard.
8a
8
Console
Wire
With the help of a second person, hold the Console
Assembly (91) near the Right Upright (54).
Tab
91
Guard
Remove the colored tie from the Wire Harness
(39). Connect the Wire Harness to the console
wire. Make sure to connect the connectors
properly (see drawing 8b). The connectors
should slide together easily and snap into
place. If they do not, turn one connector and try
again. IF THE CONNECTORS ARE NOT CON-
NECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS
Console
Wire
8b
39
54
39
TURNED ON. Insert the connectors and excess
wire into the Right Upright (54).
9. Attach the Console Assembly (91) to the Right
Upright (54) and the Left Upright (53) with four
four Handrail Bolts (8) and four Handrail Star
Washers (5). Make sure that no wires are
pinched. Start all four Handrail Bolts before
tightening them.
9
91
With the help of a second person, carefully lower
the Uprights (53, 54) to the floor.
8
8
5
5
53
54
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10. See the lower drawing. Position the Uprights
(53, 54) so that the treadmill Frame (51) is cen-
tered between the Uprights.
10
1
2
Firmly tighten the two Colored Patch Frame
Bolts (1) and the four Upright Bolts (2). Be care-
ful not to overtighten the Colored Patch
Frame Bolts.
51
Top View
54
11
53
51
11. Attach the Latch Housing (48) to the Left
Upright (53) with two Latch Screws (10); start
both Latch Screws before tightening them.
Make sure that the large hole in the Latch
Housing is on the indicated side.
53
48
Knob
Remove the knob from the pin. Make sure that
the collar and the spring are on the pin. (Note: If
there are two collars, place one on each side of
the spring.) Insert the pin into the Latch Housing
(48). Then, tighten the knob onto the pin.
Spring
Collar
Pin
10
Large Hole
Plug in the power cord (see OPERATION AND
ADJUSTMENT on page 11). Next, change the
incline of the treadmill to the lowest level as
described on page 13. If this is not done, the
latch may not hold the treadmill in the stor-
age position.
12. Make sure that all parts are properly tightened before you use the treadmill. Keep the included hex key
in a secure place. The hex key is used to adjust the walking belt (see page 19). To protect the floor or carpet,
place a mat under the treadmill.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appli-
ances being turned on or off. To decrease the possi-
bility of your treadmill being damaged, always
use a surge suppressor with your treadmill (see
drawing 1 at the right). To purchase a surge sup-
pressor, see your local HEALTHRIDER dealer or
call the toll-free telephone number on the front
cover of this manual and order part number 146148,
or see your local electronics store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Pulse Sensor
Note: If there are sheets of clear plastic
on the console, remove the plastic.
Key
Clip
FEATURES OF THE CONSOLE
HOW TO TURN ON THE POWER
The treadmill console offers a selection of features
designed to make your workouts more effective.
Plug in the power cord (see
page 10). Next, locate the
reset/off circuit breaker on
the treadmill frame near the
power cord. Make sure that
the circuit breaker is in the
“reset” position.
Reset
When you select the manual mode of the console, you
can change the speed and incline of the treadmill with
the touch of a button. As you exercise, the displays will
provide continuous exercise feedback. You can even
measure your heart rate using the built-in pulse sensor.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing above), and
slide the clip onto the waistband of your clothes. Then,
insert the key into the console. After a moment, the dis-
plays will light. Important: In an emergency situa-
tion, the key can be pulled from the console, caus-
ing the walking belt to slow to a stop. Test the clip
by carefully taking a few steps backward; if the key
is not pulled from the console, adjust the position
of the clip.
The console also offers four speed programs. Each
program automatically controls the speed of the tread-
mill as it guides you through an effective workout.
To prevent damage to the walking platform, always
wear clean athletic shoes while using the treadmill.
During the first few minutes that the treadmill is
used, inspect the alignment of the walking belt, and
center the walking belt if necessary (see page 19).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Follow your progress with the track and the
displays.
HOW TO USE THE MANUAL MODE
Insert the key into the console.
5
The track—The track
represents a distance of
1/4 mile (400 meters).
As you walk or run on
1
See HOW TO TURN ON THE POWER on page
12.
the treadmill, the indica-
tors around the track will
Select the manual mode.
2
3
appear in succession until the entire track ap-
pears. The track will then disappear and the indi-
cators will again begin to appear in succession.
The center of the track will show the number of
laps that you have completed.
When the key is in-
serted, the manual
mode will be selected.
If you have selected a
speed program, rese-
lect the manual mode
by pressing the Program Select button repeatedly
until only zeros appear in the displays.
The lower left
display—As you exer-
cise, the lower left dis-
play can show the
elapsed time and the
distance that you have
walked or run.
Start the walking belt.
To start the walking belt, press the Start button,
the Speed increase button, or one of the num-
bered speed buttons.
The lower right
display—The lower right
display can show the
speed of the walking belt
and the approximate
number of calories that
you have burned. The display also shows your
heart rate when you use the pulse sensor (see
step 6 on page 14).
If you press the Start button or the Speed in-
crease button, the walking belt will begin to move
at 1 mph. As you exercise, change the speed of
the walking belt as desired by pressing the Speed
increase and decrease buttons. Each time you
press a button, the speed setting will change by
0.1 mph; if you hold down a button, the speed set-
ting will change in increments of 0.5 mph. Note:
After you press the buttons, it may take a moment
for the walking belt to reach the selected speed set-
ting.
The upper display—
The upper display can
show the elapsed time,
the distance that you
have walked or run, the
speed of the walking
If one of the numbered speed buttons is pressed,
the walking belt will gradually change speed until it
reaches the selected speed setting.
belt, or the approximate number of calories you
have burned. Press the Priority Display button re-
peatedly until the upper display shows the informa-
tion that you are most interested in viewing. Note:
While information is shown in the upper display,
the same information will not be shown in the
lower left or lower right display.
To stop the walking belt, press the Stop button.
The time will begin to flash in one of the displays.
To restart the walking belt, press the Start button or
the Speed increase button.
Change the incline of the treadmill as desired.
4
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
To change the incline of the treadmill, hold down
the Incline increase or decrease button until the
desired incline level is reached.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The console can
display speed and dis-
tance in either miles or
kilometers. To see
which unit of measure-
ment is selected, first
heart-shaped indicator in the lower right display
will flash each time your heart beats, one or two
dashes will appear, and then your heart rate will
be shown. For the most accurate heart rate
reading, hold your thumb on the pulse sensor
for at least 15 seconds.
remove the key from the console. Next, hold down
the Stop button, reinsert the key, wait until you
hear a tone, and then release the Stop button. An
“E” for English miles or an “M” for metric kilometers
will appear in the upper display. Press the Speed
increase button to change the unit of measurement
if desired. When the desired unit of measurement
is selected, remove the key and then reinsert it.
If the displayed heart rate appears to be too high
or too low, or if your heart rate is not displayed, lift
your thumb for a few seconds, and then reposition
your thumb on the pulse sensor. Remember to
stand still while measuring your heart rate.
When you are finished exercising, remove the
key from the console.
7
Measure your heart rate if desired.
6
Step onto the foot rails and press the Stop button.
Next, remove the key from the console and put it in
a secure place.
To measure your heart rate, stand on the foot
rails and place your thumb on the pulse sensor
(see the drawing at the top of page 12). Do not
press too hard, or the circulation in your
thumb will be restricted and your pulse may
not be detected. When your pulse is detected, a
Switch the reset/off circuit breaker to the “off” posi-
tion and unplug the power cord.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
one of the displays to alert you, and then the
speed of the walking belt will change. The pro-
gram will continue until all 30 periods are com-
pleted. The walking belt will then slow to a stop.
HOW TO USE A SPEED PROGRAM
Insert the key into the console.
1
If the speed setting is too high or too low during the
program, you can manually override the setting by
pressing the Speed buttons. However, when the
next period begins, the speed of the walking
belt will change if a different speed setting is
programmed for the next period.
See HOW TO TURN ON THE POWER on page
12.
Select one of the four speed programs.
2
To select a speed pro-
gram, press the
Program Select button
repeatedly; “P-1,” “P-2,”
“P-3,” or “P-4” will ap-
To stop the program, press the Stop button. The
time will begin to flash in one of the displays. To
restart the program, press the Start button or the
Speed increase button. The walking belt will begin
to move at 1 mph. When the next period begins,
the speed of the walking belt will change if a differ-
ent speed setting is programmed for the next pe-
riod.
pear in the upper dis-
play for a few seconds to show which program is
selected. The maximum speed setting of the se-
lected program will also flash in one of the dis-
plays for a few seconds.
Change the incline of the treadmill as desired.
Each program consists of 30 one-minute periods.
One speed setting is programmed for each period.
Note: The same speed setting may be pro-
grammed for two or more consecutive periods.
The profiles on the console show how the speed
of the walking belt will change during the pro-
grams.
4
5
See step 4 on page 13.
Follow your progress with the track and the
displays.
See step 5 on pages 13 and 14.
Measure your heart rate if desired.
See step 6 on page 14.
Press the Start button or the Speed increase
button to start the program.
3
6
7
When you press either button, the treadmill will
automatically adjust to the speed setting that is
programmed for the first period of the program.
Hold the handrails and begin walking.
When you are finished exercising, remove the
key.
When the first period ends, a series of tones will
sound. If a different speed setting is programmed
for the second period, the speed setting will flash in
See step 7 on page 14.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. Next, unplug the power cord. CAUTION:
You must be able to safely lift 45 lbs. (20 kg) to raise,
lower, or move the treadmill.
Frame
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the pos-
sibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight. As you raise the frame, make sure to lift
with your legs rather than your back. Raise the frame
about halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the frame until the catch is
past the latch pin. Then, slowly release the latch knob;
make sure that the catch is resting against the latch
pin.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of di-
rect sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85°F (30°C).
Latch
Pin
Latch
Knob
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the catch
is resting against the latch pin.
Handrail
1. Hold the handrails and place one foot against one of the
wheels. Do not pull back on the frame.
2. Tilt the treadmill backward until it rolls freely on the wheels,
and carefully move the treadmill to the desired location.
Never move the treadmill without tipping it backward.
To reduce the risk of injury, use extreme caution
while moving the treadmill. Do not attempt to move
the treadmill over an uneven surface.
Wheel
3. Place one foot against one of the wheels, and carefully
lower the treadmill until it is in the storage position.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand as
shown. Using your left hand, pull the latch knob to the left
and hold it. Next, lower the frame until it is past the latch
pin. Then, release the latch knob.
Latch
Pin
Latch
Knob
2. Hold the frame firmly with both hands, and lower it to the
floor. To decrease the possibility of injury, bend your
legs and keep your back straight.
Frame
17
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 11. Important: The treadmill is not com-
patible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes,
and then press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
a
20
65
POWER CORD. Remove the five indicated Screws
(20). Then, carefully remove the Hood (65).
20
Locate the Reed Switch (89) and the Magnet (62) on
the left side of the Pulley (71). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8". If necessary, loosen the Screw
(3), move the Reed Switch slightly, and then retighten
the Screw. Reattach the Hood (not shown), and run
the treadmill for a few minutes to check for a correct
speed reading.
1/8"
3
71
62
89
Top View
18
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 11.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
2–3"
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 2 to 3 inches off
the walking platform. Be careful to keep the walking
belt centered. Then, plug in the power cord, insert the
key, and run the treadmill for a few minutes. Repeat
until the walking belt is properly tightened.
Rear Roller
Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt has shifted to the left, first re-
a
move the key and UNPLUG THE POWER CORD.
Using the hex key, turn the left rear roller bolt clock-
wise 1/2 of a turn. Be careful not to overtighten the
walking belt. If the walking belt has shifted to the
right, turn the left rear roller bolt counterclockwise 1/2
of a turn. Then, plug in the power cord, insert the key,
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
SOLUTION: a. If the walking belt slips when walked on, first remove
b
the key and UNPLUG THE POWER CORD. Using the
hex key, turn both rear roller bolts clockwise, 1/4 of a
turn. When the walking belt is correctly tightened, you
should be able to lift each edge of the walking belt 2 to
3 inches off the walking platform. Be careful to keep
the walking belt centered. Then, plug in the power
cord, insert the key, and carefully walk on the treadmill
for a few minutes. Repeat until the walking belt is
properly tightened.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
EXERCISE FREQUENCY
To measure your heart rate during exercise, use the
pulse sensor on the console.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back foot
flat on the floor. Bend your front leg, lean forward and move your
hips toward the wall. Hold for 15 counts, then relax. Repeat 3 times
for each leg. To cause further stretching of the achilles tendons,
bend your back leg as well. Stretches: Calves, achilles tendons and
ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks
as possible. Hold for 15 counts, then relax. Repeat 3 times for each
leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
5
21
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. HRTL34306.1
R0806A
To locate the parts listed below, see the EXPLODED DRAWING on pages 24 to 27.
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2
6
2
13
4
1
2
4
6
16
4
1
4
2
1
4
1
1
4
Colored Patch Frame Bolt
Upright Bolt/Lift Frame Bolt
Wire Tie Screw/Reed Switch Screw
Console Back Screw
Handrail Star Washer
Warning Decal
Crossbar Star Washer
Handrail Bolt
Upright Star Washer
Console Screw/Latch Screw
Frame Spacer
Console Back
Wheel Housing Bolt
Upright Washer
Key/Clip
Nut
6 mm Hex Key
4 mm Hex Key
Roller Bracket Screw/
Front Platform Screw
Hood Screw
Screw
Left Handrail
Lift Frame
Latch Pin Assembly
Foot Rail Screw
Base Pad Screw
Walking Platform Bolt
Belt Guide Screw
Rear Roller Adj. Bolt
Motor Bolt
Motor Pivot Bolt
Wheel Housing Washer
Right Handrail
Motor Tension Bolt
Wheel Bolt
Rear Roller Star Washer
Reset/Off Circuit Breaker
Motor Star Washer
Wire Harness
Incline Motor
Screw
Electronics Star Washer
Wheel Housing Nut
Motor Tension Nut/Platform Nut
Wheel Housing
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
1
3
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
6
1
1
1
1
1
4
2
1
1
1
1
4
1
4
2
1
2
9
1
1
1
2
1
1
1
1
1
1
Motor Pivot Nut
Hood Clip
Latch Housing
Grommet
Isolator Fastener
Frame
Base
Left Upright
Right Upright
Rear Roller
Motor Belt
Electronics Bracket
Incline Motor Bolt, Upper
Motor Bracket
Left Rear Roller Bracket
Right Rear Roller Bracket
Magnet
Base Pad
Latch Catch
Hood
Belly Pan
Left Foot Rail
Right Foot Rail
Wheel Spacer
Wheel
Front Roller/Pulley
Incline Motor Bolt, Lower
Access Door
Rear Foot, Left
Upright Nut
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
3
6
1
1
1
10
6
2
4
2
2
1
4
1
2
2
2
1
2
1
1
4
5
4
2
2
Walking Belt
Handrail Endcap
Platform Cushion
Drive Motor
Wire Tie
8" Tie
Incline Motor Nut, Upper
Reed Switch Clip
Silver Ground Screw
Crossbar Screw
Walking Platform
Controller
Console Crossbar
Reed Switch
Power Cord
Console Assembly
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
92
93
94
95
96
97
98
99
100
101
1
2
1
2
1
1
1
1
1
2
Incline Motor Nut, Lower
Belt Guide
5 mm Hex Key
Frame Endcap
Releasable Tie
Rear Foot, Right
Filter Wire
Power Cord Grommet
Incline Motor Wire
Front Roller Washer
102
#
#
#
#
2
1
1
1
1
1
Controller Screw
6" Red Wire, M/F
8" Black Wire, M/F
4" Blue Wire, 2F
10" Blue Wire, 2F
User’s Manual
#
# These parts are not illustrated.
Specifications are subject to change without notice.
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to pro-
vide the following information when calling:
• the MODEL NUMBER of the product (HRTL34306.1)
• the NAME of the product (HEALTHRIDER H110i treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING on pages 22 to 27 )
23
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING A—Model No. HRTL34306.1
R0806A
1
4
1
1
1
8
4
4
1
4
1
0
6
1
3
1
9
1
3
7
1
8
9
2
1
5
1
0
2
4
5
4
9
0
6
1
5
6
8
1
4
7
0
1
3
1
1
7
8
6
2
9
1
6
3
9
5
6
8
8
7
1
4
5
9
2
1
1
8
1
6
6
8
8
6
2
1
5
2
3
5
4
9
7
2
4
2
4
4
7
9
9
0
1
4
4
1
1
6
6
0
5
1
2
1
5
5
2
2
9
2
8
5
4
7
7
5
0
6
5
9
6
2
3
6
5
4
2
4
9
0
1
1
0
7
6
5
2
9
1
2
6
2
4
4
3
7
9
5
2
2
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING B—Model No. HRTL34306.1
R0806A
47
47
47
65
58
82
2
72
100
40
23
92
97
2
34
30
38
21
42
21
21
44
38
42
102
34
59
57
79
20
87
66
20
37
20
90
99
21
49
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING C—Model No. HRTL34306.1
R0806A
77
77
88
10
33
10
10
10
7
10
10 10
85
10
7
5
85
39
8
8
22
5
5
77
77
3
48
24
103
10
80
54
53
11
1
9
2
14
11
2
2
52
49
9
14
13
32
1
63
26
9
32
43
43
75
39
35
63
26
63
26
63
26
84
69
70
45
13
16
69
9
32
43
16
75
43
45
63
26
35
69
70
63
26
69
26
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING D—Model No. HRTL34306.1
R0806A
91
15
4
12
4
4
4
4
4
4
4
73
4
4
27
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
WHAT IS COVERED—The entire HealthRider H110i treadmill (“Product”) is warranted to be free of all defects in mate-
rial and workmanship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the drive motor for 3 years. Parts and
labor are warranted for 90 days from the date of purchase.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or
component, providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized
service provider, or, at our option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, im-
proper assembly or installation, alterations, modifications without our written authorization or by failure on your part to
use, operate, and maintain as set out in your User’s Manual (“Manual”). This warranty does not extend to products used
for commercial or rental purposes.
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the
Product as specified in the Manual; notify our Customer Service Department of any defect within 10 days after discov-
ery of the defect; as instructed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product.
Remember to do the periodic maintenance requirements specified in the Manual to assure proper operation and your
continued satisfaction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-888-922-4222 and tell them
your name and address and the serial number of your Product. They will tell you how to get a part replaced, or if neces-
sary, arrange for service where your Product is located or advise you how to ship the Product for service. Before ship-
ping, always obtain a Return Authorization Number (RA No.) from our Customer Service Department; securely pack
your Product (save the original shipping carton if possible); put the RA No. on the outside of the carton and insure the
product. Include a letter explaining the product or problem and a copy of your proof of purchase if you believe the ser-
vice is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the
use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or
profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature.
Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above lim-
itation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability
or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not
allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty.
This warranty gives you specific legal rights and you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 244809 R0806A
Printed in USA © 2006 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|