®
Model No. HRTL09990
Serial No.
Write the serial number in the space
above for future reference.
USER'S MANUAL
Serial Number Decal
QUESTIONS?
As a manufacturer, we are
committed to providing com-
plete customer satisfaction. If
you have questions, or if there
are missing parts, we will guar-
antee complete satisfaction
through direct assistance from
our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.– 6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this man-
ual for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
11. Keep the power cord and the surge protector
away from heated surfaces.
12. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the tread-
mill is not working properly.)
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with
eight feet of clearance behind it. Do not place
the treadmill on any surface that blocks air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
13. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Do not use the hand weights at speeds higher
than a walk. Using hand weights and not hold-
ing the handrails may compromise your ability
to maintain your balance. Exercises using
hand weights should be attempted only by ex-
perienced users.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 250 pounds. Never allow
more than one person on the treadmill at a
time.
16. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the on/off switch to
the off position when the treadmill is not in
use. (See the drawing on page 5 for the loca-
tion of the on/off switch.)
8. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose cloth-
ing that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
17. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO MOVE
THE TREADMILL on page 21.) You must be
able to safely lift 45 pounds (20 kg) in order
to raise, lower, or move the treadmill.
9. When connecting the power cord (see page
7), plug the power cord into a surge protector
(not included) and plug the surge protector
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be
on the same circuit.
18. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
19. Inspect and tighten all parts of the treadmill
every three months.
10. Use only a UL-listed surge protector, rated at
15 amps, with a 14-gauge cord of five feet or
less in length. Do not use an extension cord.
20. Never drop or insert any object into any
opening.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
other than the procedures in this manual
should be performed by an authorized ser-
vice representative only.
20.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
21. The treadmill is intended for in-home use
only. Do not use the treadmill in any
commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown below have been placed on your treadmill. If a decal is missing, or if it is not legible,
please call our Customer Service Department toll-free at 1-800-999-3756 to order a free replacement decal.
Apply the decal in the location shown. Note: The large decal is shown at 38% of actual size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for purchasing the SOFTSTRIDER
S300i™ treadmill by HealthRider®. The SOFTSTRIDER
S300i offers an impressive array of features to help
you achieve your fitness goals in the convenience of
your home. From the advanced console to the cush-
ioned walking belt, the SOFTSTRIDER S300i is de-
signed to make each workout more effective and en-
joyable. And when you’re not exercising, the SOFT-
STRIDER S300i can be folded away, taking less than
half the floor space of conventional treadmills.
have additional questions, please call our Customer
Service Department toll-free at 1-800-999-3756,
Monday through Friday, 6 a.m. until 6 p.m. Mountain
Time (excluding holidays). To help us assist you,
please note the product model number and serial num-
ber before calling. The model number is HRTL09990.
The serial number can be found on a decal attached to
the treadmill (see the front cover of this manual for the
location).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
For your benefit, read this manual carefully before
using the SOFTSTRIDER S300i treadmill. If you
Hand Weights
Book Holder
Console
Chest Pulse Sensor Holder*
Water Bottle Holder†
Handrail
Key/Clip
Lock Knob
RIGHT SIDE
On/Off
Switch
Walking Belt
Circuit
Breaker
Foot Rail
Power
Cord
Cushioned
Walking Platform
BACK
Rear Roller
Adjustment Bolts
*For information about the optional chest
pulse sensor, see page 20.
†Water bottle is not included.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two people. Place the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until the treadmill is assembled. No tools are required.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt, the sides of the walking platform, or
the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt or
on the sides of the walking platform, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
1. With the help of a second person, carefully raise the
1
Uprights (103) until the Wheels (99) are resting on the
floor as shown.
103
99
2. Next, make sure that the Lock Knob Sleeve (68) is fully
2
inserted into the left Upright (103).
Remove the Lock Knob (67) from the Lock Pin (72). Make
sure that the Lock Pin Collar (70) and the Spring (69) are
on the Lock Pin. Insert the Lock Pin into the left Upright
(103) and tighten the Lock Knob onto it.
103
69
70
72
68
67
3. Make sure that all parts are tightened before you use the treadmill. Place a mat beneath the treadmill
to protect the floor or carpet. For your benefit, we recommend that you familiarize yourself with the
TROUBLE-SHOOTING AND MAINTENANCE section on pages 22 and 23.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
GROUNDING INSTRUCTIONS
TM
THE PERFORMANT LUBE WALKING BELT
of electric shock. This product is equipped with a cord
having an equipment-grounding conductor and a
grounding plug. Plug the power cord into a surge
protector, and plug the surge protector into an ap-
propriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge protector to a 2-pole recep-
tacle as shown in drawing 2 if a properly grounded out-
let is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet in-
stalled by a qualified electrician.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can re-
sult from weather conditions or from other appliances
being turned on or off.
To decrease the pos-
sibility of your tread-
1
Grounded Outlet Box
mill being damaged,
always use a surge
protector (not in-
cluded) with your
treadmill.
Treadmill Power Cord
Grounding Pin
Grounding Plug
Grounding Plug
Grounding Pin
Surge protectors are
sold at most hardware
stores and department
stores. Use only a UL-
listed surge protector,
rated at 15 amps, with a
14-gauge cord of five
feet or less in length.
Grounded Outlet
2
Grounded Outlet Box
Adapter
Grounding Pin
Grounding Plug
This product must be
grounded. If it should
malfunction or break
down, grounding pro-
vides a path of least re-
sistance for electric cur-
rent to reduce the risk
Surge Protector
Lug
Metal Screw
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM OF THE CONSOLE
J
O
K
L
C
B
M
N
A
R
D
E
P Q
F
G
Note: If there is a thin
sheet of clear plastic
on the face of the
console, remove it.
I
H
FEATURES OF THE CONSOLE
music provides added motivation. Each CD features
two programs designed by certified personal trainers.
The treadmill console offers an impressive selection of
features to help you get the most from your exercise.
In addition, you can connect the treadmill to your VCR
and TV and play iFit.com video programs (videocas-
settes are available separately). Video programs offer
the same benefits as iFit.com CD programs, but add
the excitement of working out with a class and an
instructor—the hottest new trend at health clubs.
When the console is in the manual mode, the speed
and incline of the treadmill can be changed with a
touch of a button. As you exercise, the four displays
will show your workout time, the number of calories
you have burned, the distance you have walked, the
incline level of the treadmill, and the speed of the walk-
ing belt. If you purchase an optional handgrip pulse
sensor or chest pulse sensor, the console will also
show your heart rate.
With the treadmill connected to your computer, you
and access basic programs that interactively control
the speed and incline of your treadmill to help you
achieve your specific exercise goals. Or, use iFit.com
audio and video programs directly from our internet
The console also offers four preset workout programs.
Each program automatically controls the speed and in-
cline of the treadmill as it guides you through an effec-
tive workout. The included hand weights can be used for By adding an optional upgrade module to the treadmill,
upper body exercise as well. If you purchase the op-
tional chest pulse sensor, the console’s two pulse pro-
grams can also be used. Each program controls the
speed and incline of the treadmill to keep your heart rate
within a preset range during your workouts.
you can use virtually endless features from our internet
features.
To purchase iFit.com CD’s, iFit.com videocassettes,
or an optional upgrade module, call toll-free 1-800-735-
0768. For information about the optional handgrip pulse
sensor or chest pulse sensor, see page 20.
The console also features advanced iFit.com technol-
ogy. IFit.com technology is like having a personal
trainer right in your home. Using the included audio
cable, you can connect the treadmill to your home
stereo, portable stereo, or computer and play special
iFit.com CD programs (CD’s are available separately).
IFit.com CD programs automatically control the speed
and incline of the treadmill as a personal trainer guides
you through every step of your workout. High-energy
To use the manual mode of the console, follow the
steps beginning on page 10. To use a preset program,
see page 12. To use a pulse program, see page 13.
To use iFit.com CD or video programs, see page 17.
To use iFit.com programs directly from our inter-
net site, see page 19.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION OF THE CONSOLE
WARNING:
Do not use the
Refer to the drawing on page 8 to identify the features
described below.
hand weights at speeds higher than a walk.
Using hand weights and not holding the
handrails may compromise your ability to
maintain your balance. Exercises using
hand weights should be attempted only by
experienced users.
A. Water bottle holder—This holder keeps your water
bottle handy during your workouts (no water bottle
is included).
B. Hand weight holder—These compartments hold the
included hand weights.
L. Calories/Pulse display—This display shows the ap-
proximate number of calories you have burned.
When the optional chest pulse sensor is worn, the
display will also show your heart rate. The display
will alternate between one number and the other
every seven seconds. If the optional handgrip pulse
sensor is used, the display will show your heart rate
continuously while your hands are on the pulse sen-
sor.
C. Book holder—This holder allows you to read a good
book or enjoy your favorite magazine while you get
in shape.
D. Incline buttons—These buttons control the incline of
the treadmill. The incline range is 1.5% to 10%.
E. Speed buttons—These buttons control the speed of
the walking belt. The speed range is 0.5 mph to 10
mph.
M. Distance/Incline display—This display shows the
distance you have walked and the incline level of
the treadmill. The display will alternate between one
number and the other every seven seconds. Note:
Each time the Incline buttons are pressed, the dis-
play will change to show the incline setting.
F. Stop buttons—These buttons are used to stop the
walking belt. Note: Pressing either button will stop
the walking belt.
G. Start button—This button is used to start the walking
belt.
N. Speed display—This display shows the speed of
the walking belt.
H. Waistband clip—This clip is designed to be worn on
the waistband of your clothes. If the key is pulled
from the console, the walking belt will automatically
stop.
O. Enter button and
L
and
M
buttons—These buttons
are used to enter your age when pulse programs
are used.
P. Select Workout button—This button is used to select
the manual mode, the four preset programs, the two
pulse programs, and iFit.com programs. Note: If the
walking belt is moving when the Select Workout
button is pressed, the walking belt will slow to a
stop and the displays will be reset.
I. Key—This key turns the console on and off.
J. Time/Segment Time display—When the manual
mode or an iFit.com program is selected, this display
will show the elapsed time. When a preset program
or a pulse program is selected, the display will show
both the time remaining in the program and the time
remaining in the current segment of the program.
The display will alternate between one number and
the other every seven seconds.
Q. Mode indicators—These indicators show whether
the manual mode, a preset program, a pulse pro-
gram, or an iFit.com program is selected.
R. Program profiles—These profiles show how the tar-
get heart rate will change during pulse programs
and how the speed and incline of the treadmill will
change during preset programs.
K. Cross Training indicator—During the Fitnesswalk
and Cardiojog programs, this indicator will periodi-
cally flash. The included hand weights can be used
while the indicator is flashing to add upper body
exercise to your workouts.
Note: The console can display exercise feedback
in either miles or kilometers (see SPEED DISPLAY
on page 11). For simplicity, all instructions in this
section refer to miles.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE MANUAL MODE
WARNING:
To reduce the risk of
serious injury, read the following precautions
before operating the console.
Insert the key into the console.
1
• Do not stand on the walking belt when turn-
ing on the power or starting the walking belt.
See HOW TO TURN ON THE POWER at the left.
Select the manual mode.
2
• Always attach the clip (see “H”on page 8) to
your waistband when using the treadmill. If
the key is pulled from the console, the walk-
ing belt will stop.
When the key is in-
serted, the manual
mode will be selected
and the manual indica-
tor will light. If a pro-
gram has been se-
• The treadmill is capable of high speeds.
Adjust the speed in small increments.
lected, press the Select
Workout button repeatedly to select the manual
mode.
• To reduce the risk of electric shock, keep
liquids away from the console and place only
a sealed water bottle in the console.
Press the Start button or the Speed
to start the walking belt.
L
button
• Do not use the hand weights at speeds higher
than a walk. Using hand weights and not hold-
ing the handrails may compromise your ability
to maintain your balance. Exercises using
hand weights should be attempted only by ex-
perienced users.
3
A moment after the button is pressed, the walking
belt will begin to move at 1.0 mph. Hold the hand-
rails and begin walking.
• If you have heart problems, or if you are over
60 years of age and have been inactive, do
not use the pulse programs. If you are taking
medication regularly, consult your physician
to find whether the medication will affect
your exercise heart rate. Note: The pulse pro-
grams require an optional chest pulse sensor.
As you exercise, adjust
the speed of the walking
belt as desired by press-
ing the Speed buttons.
Each time one of the
buttons is pressed, the
speed will change by
0.1 mph. If one of the buttons is held down, the
speed will change in increments of 0.5 mph.
HOW TO TURN ON THE POWER
To stop the walking belt, press either of the Stop
buttons. The four displays will pause and the
Time/Segment Time display will begin to flash. To
restart the walking belt, press the Start button or
Plug in the power cord (see HOW TO PLUG IN
1
THE POWER CORD on page 7).
the Speed
L
button. To stop the walking belt and
reset the displays, press a Stop button, remove
the key, and then reinsert the key.
Locate the on/off
switch on the front of
2
On
Position
the treadmill near the
power cord. Make
sure that the on/off
switch is in the on
position.
Adjust the incline of the treadmill.
4
To vary the intensity of
your exercise, adjust the
incline of the treadmill
as desired with the
Incline buttons. Each
time one of the buttons
is pressed, the incline
will change by 0.5%. The incline range is 1.5% to
10%. Note: After the buttons are pressed, it may
take a moment for the treadmill to reach the se-
lected incline setting.
Stand on the foot
rails of the treadmill.
Find the clip attached
to the key and slide
the clip onto the
waistband of your
clothing. Next, insert
the key into the console. After a moment, the four
displays and various indicators will light.
3
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Speed display—This
display shows the speed
of the walking belt.
Follow your progress with the four displays.
5
Time/Segment Time
display—When the
manual mode or an
iFit.com program is
selected, this display
will show the elapsed
Note: The speed can be
displayed in either miles
time. When a preset
per hour (mph) or kilo-
meters per hour (kph).
To see which unit of
measurement is se-
program or a pulse program is selected, the display
will show both the time remaining in the program
and the time remaining in the current segment of
the program. The display will alternate between
one number and the other every seven seconds.
lected, first hold down
one of the Stop buttons while inserting the key into
the console. The Speed display will show an “E”
for English miles or an “M” for metric kilometers.
Note: The Cross Training indicator below the dis-
play will periodically flash during the Fitnesswalk
and Cardiojog programs. While the indicator is
flashing, the included hand weights can be used for
upper body exercise as you walk on the treadmill.
Press the Speed
L
button to change the unit of
measurement. When the desired unit of measure-
ment is selected, remove and then reinsert the key.
Calories/Pulse
display—This display
shows the approximate
When you are finished exercising, stop the
walking belt and remove the key.
6
number of calories you
have burned. When the
optional chest pulse
sensor is worn, the dis-
play will also show your heart rate. The display
will alternate between one number and the other
every seven seconds. If the optional handgrip
pulse sensor is used, the display will show your
heart rate continuously while your hands are on
the pulse sensor.
Step onto the foot rails, press one of the Stop but-
tons, and adjust the incline of the treadmill to 1.5%.
The incline must be at 1.5% when the treadmill
is raised to the storage position or the treadmill
will be damaged. Next, remove the key from the
console and put it in a safe place. Note: If the dis-
plays and indicators on the console remain lit
after the key is removed, the console is in the
“demo” mode. Refer to page 20 and turn off the
demo mode.
Distance/Incline
display—This display
shows the distance you
have walked and the
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
incline level of the
treadmill. The display
will alternate between
one number and the other every seven seconds.
Note: Each time the Incline buttons are pressed,
the display will change to show the incline setting.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The program will continue in this way until the
Time/Segment Time display counts down to zero.
The walking belt will then slow to a stop.
HOW TO USE THE PRESET PROGRAMS
Insert the key into the console.
1
If the speed or incline setting for the current seg-
ment is too high or too low, you can manually
override the setting by pressing the Speed or
Incline buttons on the console. However, when
the next segment begins, the treadmill will au-
tomatically adjust to the speed and incline set-
tings for the next segment.
See HOW TO TURN ON THE POWER on page 10.
Select one of the four preset programs.
2
When the key is
inserted, the
manual mode
will be selected
and the manual
indicator will
To stop the program temporarily, press one of the
Stop buttons. All displays will pause and the Time/
Segment Time display will begin to flash. To
restart the program, press the Start button or the
light. To select
one of the pre-
set programs,
press the Select
Speed
L
button. To end the program, press a Stop
button, remove the key, and then reinsert the key.
Workout button repeatedly until one of the four
preset program indicators lights.
Use the hand weights, if desired.
4
If you have selected the
The profiles on the console show how the speed
and incline of the treadmill will change during the
preset programs—the white profiles show speed
settings and the green lines show incline settings.
The numbers at the left ends of the profiles show
the speed and incline ranges for the programs.
For example, during the Healthwalk program, the
speed of the walking belt will be from 2 mph to 4
mph and the incline will be from 1.5% to 6%. The
Time/Segment Time display will show how long
the selected program will last.
Fitnesswalk or Cardio-
jog program, the Cross
Training Indicator in the
Time/Segment Time
display will periodically
flash. While the indicator
is flashing, use the included hand weights for upper
body exercise as you walk on the treadmill.
Follow your progress with the four displays.
Refer to step 5 on page 11.
5
6
Press the Start button or the Speed
to start the program.
L
button
3
When the program has ended, remove the key.
Step onto the foot rails and make sure that the in-
cline of the treadmill is at 1.5%. The incline must
be at 1.5% when the treadmill is raised to the
storage position. Next, remove the key from the
console and put it in a safe place. Note: If the dis-
plays and indicators on the console remain lit
after the key is removed, the console is in the
“demo” mode. Refer to page 20 and turn off the
demo mode.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each program is di-
vided into several time
segments of different
lengths. The Time/
Segment Time display
will show both the time
remaining in the pro-
gram and the time remaining in the current seg-
ment. One speed setting and one incline setting
are programmed for each segment. When only
three seconds remain in the first segment of the
program, a series of tones will sound and the
treadmill will automatically adjust to the speed and
incline settings for the second segment.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter a maximum heart rate setting.
HOW TO USE THE PULSE PROGRAMS
4
After you have
Note: The pulse programs can be used only when
the optional chest pulse sensor is worn. See page
20 for information about the chest pulse sensor.
entered your
age, another
number will
begin to flash in
Insert the key into the console.
the CALORIES/
PULSE display.
1
See HOW TO TURN ON THE POWER on page 10.
This number is the maximum heart rate setting for
the program. If Pulse program 1 is selected, the
maximum heart rate setting can be from 65% to
85% of your maximum possible heart rate (your
maximum possible heart rate is 220 minus your
age); if Pulse program 2 is selected, the maximum
heart rate setting can be from 65% to 80% of your
maximum possible heart rate. Note: Your maxi-
mum possible heart rate is an estimate only.
Put on the chest pulse sensor.
2
You must wear the chest pulse sensor in order to
use a pulse program. To put on the chest pulse
sensor, follow the instructions included with the
chest pulse sensor.
Select one of the two pulse programs.
3
For example, if you are 30 years old, your maxi-
mum possible heart rate is 190 (220 minus 30
equals 190). Therefore, if Pulse program 1 is se-
lected, the maximum heart rate setting can be from
123 to 161 (65% of 190 is 123; 85% of 190 is 161).
When the key is
inserted, the
manual mode
will be selected
and the manual
indicator will
light. To select
one of the pulse programs, press the Select
Workout button repeatedly until one of the two
pulse program indicators lights.
If you want to change the maximum heart rate set-
ting, press the
L
and
M
buttons. The buttons can
be held down to change the setting quickly. When
the desired setting is shown, press the Enter button.
Press the Start button or the Speed
to start the program.
L
button
5
The profiles on the console show how the target
heart rate will change during the programs. The
Time/Segment Time display will show how long
the selected program will last.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Enter your age.
4
Each program is divided
into several time seg-
ments of different
lengths. The Time/
Segment Time display
will show both the time
remaining in the pro-
When a pulse
program is se-
lected, an age
setting will begin
to flash in the
CALORIES/
PULSE display.
gram and the time remaining in the current seg-
ment. One target heart rate setting is programmed
for each segment. When only three seconds re-
main in the first segment of the program, a series
of tones will sound and the next segment will
begin. As you exercise, the speed and/or incline of
the treadmill will automatically change as needed
to keep your heart rate near the current target
heart rate setting.
If you have already entered your age, simply press
the Enter button. To enter your age, press the
LL
and buttons. The buttons can be held down to
M
enter your age quickly. When your age is shown,
press the Enter button.
The program will continue until the Time/Segment
Time display counts down to zero. The walking
belt will then slow to a stop.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
If your heart rate is not detected during the pro-
gram, the speed and incline of the treadmill may
automatically decrease until your heart rate is de-
tected. If this happens, see the instructions in-
cluded with the chest pulse sensor.
Follow your progress with the four displays.
Refer to step 5 on page 11.
6
7
When the program has ended, remove the key.
If the speed or incline setting for the current seg-
ment is too high or too low, you can adjust the set-
ting with the Speed or Incline buttons. However, if
you decrease the speed, the incline will automati-
cally increase; if you increase the speed, the in-
cline will decrease. If you increase the incline, the
speed will decrease; if you decrease the incline,
the speed will increase. The treadmill will always
attempt to keep your heart rate near the target
heart rate setting for the current segment. Note:
When the incline reaches the lowest setting, the
speed cannot be increased any further. When the
incline reaches the highest setting, the speed can-
not be decreased any further.
Step onto the foot rails and make sure that the in-
cline of the treadmill is at 1.5%. The incline must
be at 1.5% when the treadmill is raised to the
storage position. Next, remove the key from the
console and put it in a safe place. Note: If the dis-
plays and indicators on the console remain lit
after the key is removed, the console is in the
“demo” mode. Refer to page 20 and turn off the
demo mode.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
To stop the program temporarily, press one of the
Stop buttons. All displays will pause and the Time/
Segment Time display will begin to flash. To
restart the program, press the Start button or the
Speed
L
button. To end the program, press a Stop
button, remove the key, and then reinsert the key.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFit.com CD’s, the treadmill must be con-
nected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
15 and 16 for connecting instructions. To use iFit.com
videocassettes, the treadmill must be connected to
your VCR. See page 17 for connecting instructions. To
use iFit.com programs directly from our internet
site, the treadmill must be connected to your home
computer. See page 16 for connecting instructions.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
LEFT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
Audio
Cable
Adapter
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
PHONES LINE OUT
LINE OUT
PHONES
B
Head-
phones
Audio
Cable
LINE OUT
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
B
PHONES
C
PHONES
3.5mm
Y-adapter
Audio
Cable
PHONES
3.5mm
Y-adapter
Audio
Cable
Headphones
Headphones
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA adapter (available at
electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
RCA adapter. Plug the RCA adapter into the LINE
OUT jack on your stereo.
B
PHONES
B
CD
Audio
Cable
3.5mm
Y-adapter
VCR
Amp
LINE OUT
Headphones/Speakers
RCA
Adapter
Audio
Cable
Adapter
Wire removed from
LINE OUT jack
16
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 16.
To use iFit.com CD’s or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on page
15. Note: To purchase iFit.com CD’s or iFit.com
videocassettes, call toll-free 1-800-735-0768.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
Follow the steps below to use an iFit.com CD or video
program.
A
Insert the key into the console.
ANT IN
.
VIDEO AUDIO
IN
RF OUT
1
CH
3
4
OUT
AUDIO OUT
See HOW TO TURN ON THE POWER on page 10.
RIGHT
LEFT
Select the iFit.com mode.
2
Audio
Cable
Adapter
When the key is in-
serted, the manual
mode will be selected
and the manual indica-
tor will light. To use
iFit.com CD’s or video-
cassettes, press the
Select Workout button repeatedly until the iFit.com
indicator lights.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA adapter (available at
electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
RCA adapter. Plug the RCA adapter into the AUDIO
OUT jack on your VCR.
Insert the iFit.com CD or videocassette.
3
If you are using an iFit.com CD, insert the CD into
your CD player. If you are using an iFit.com video-
cassette, insert the videocassette into your VCR.
Press the PLAY button on your CD player or
VCR.
4
B
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
A moment after the button is pressed, your per-
sonal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions.
RCA Adapter
Adapter
Audio
Cable
During the CD or video program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
Wire removed from
AUDIO OUT jack
17
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
Follow your progress with the four displays.
5
6
See step 5 on page 11.
When the program is completed, remove the
key.
To stop the walking belt at any time, press a Stop
button on the console. The Time/Segment Time
display will begin to flash. To restart the program,
press the Start button. After a moment, the walk-
ing belt will begin to move at 1.0 mph. When the
next “chirp” is heard, the speed and incline
will change to the next settings of the CD or
video program. The program can also be
stopped by pressing the Stop button on your CD
player or VCR.
Step onto the foot rails and make sure that the in-
cline of the treadmill is at 1.5%. The incline must
be at 1.5% when the treadmill is raised to the
storage position. Next, remove the key from the
console and put it in a safe place. Note: If the dis-
plays and indicators on the console remain lit
after the key is removed, the console is in the
“demo” mode. Refer to page 20 and turn off the
demo mode.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
When the CD or video program is completed, the
walking belt will stop and the Time/Segment Time
display will begin to flash. Note: To use another
CD or video program, press a Stop button or re-
move the key and go to step 1 on page 17.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard:
• make sure that the iFit.com indicator is lit and
that the Time/Segment Time display is not
flashing
• adjust the volume of your CD player or VCR. If
the volume is too high or too low, the console
may not detect the program signals
• make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord
• if you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the key onto the waistband of your clothing.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR INTERNET SITE
7
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking.
access a selection of programs that interactively con-
trol your treadmill to help you achieve your specific ex-
ercise goals. In addition, you can play iFit.com audio
and video programs directly from the internet. By
adding an optional upgrade module to the console, you
can use virtually endless features on our internet site.
grade module, call toll-free 1-800-735-0768.
During the program, an electronic “chirping” sound
will alert you when the speed and/or incline of the
treadmill is about to change. CAUTION: Always
listen for the “chirp” and be prepared for speed
and/or incline changes.
To use programs from our internet site, the treadmill
must be connected to your home computer. See HOW
TO CONNECT YOUR COMPUTER on page 16. In
addition, you must have an internet connection and
an internet service provider. A list of specific system
requirements will be found on our internet site.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the program.
Follow the steps below to use a program from our
internet site.
To stop the walking belt at any time, press a Stop
button on the console. The Time/Segment Time
display will begin to flash. To restart the program,
press the Start button. After a moment, the walk-
ing belt will begin to move at 1.0 mph. When the
next “chirp” is heard, the speed and incline will
change to the next settings of the program.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 10.
Select the iFit.com mode.
2
When the program is completed, the walking belt
will stop and the Time/Segment Time display will
begin to flash. Note: To use another program,
press a Stop button and go to step 5.
When the key is in-
serted, the manual
mode will be selected
and the manual indica-
tor will light. To use a
program from our inter-
net site, press the
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFit.com indicator is lit and that
the Time/Segment Time display is not flashing.
In addition, make sure that the audio cable is
properly connected, that it is fully plugged in,
and that it is not wrapped around a power cord.
Program Select button repeatedly until the
iFit.com indicator lights.
Go to your computer and start an internet
connection.
3
Follow your progress with the four displays.
See step 5 on page 11.
8
9
Start your web browser, if necessary, and go to
4
Follow the desired links on our internet site to
select a program.
When the program has ended, remove the key.
5
Step onto the foot rails and make sure that the in-
cline of the treadmill is at 1.5%. Remove the key
from the console and put it in a safe place. Note: If
the displays and indicators on the console re-
main lit after the key is removed, the console is
in the “demo” mode. Refer to page 20 and turn
off the demo mode.
Read and follow the on-line instructions for using a
program.
Follow the on-line instructions to start the
program.
6
When you start the program, an on-screen count-
down will begin.
Next, move the on/off switch near the power cord
to the off position and unplug the power cord.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE/DEMO MODE
THE OPTIONAL CHEST PULSE SENSOR
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also al-
lows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.
An optional chest pulse sensor adds even more
features to the console. The chest pulse sensor contin-
uously monitors your heart rate during your workouts
and allows you to use the console’s two pulse pro-
grams. To purchase the optional chest pulse sen-
sor, call toll-free 1-800-201-2172.
To select the information mode, hold down one of the
Stop buttons while inserting the key into the console.
When the information mode is selected, the following
information will be shown:
The Time/Segment Time
display will show the total
number of hours that the
treadmill has been used.
THE OPTIONAL HANDGRIP PULSE SENSOR
The Distance/Incline display
will show the total number of
miles that the walking belt
has moved.
An optional hand-
grip pulse sensor
allows you to con-
veniently measure
your heart rate be-
fore you begin ex-
ercising, during
your workout, and
after you finish. To
purchase the op-
tional chest pulse
sensor, call toll-
free 1-800-201-2172.
An “E,” for English miles, or
an “M,” for metric kilometers,
will appear in the Speed dis-
play. Press the Speed
LL
button to change the unit of
measurement.
IMPORTANT: The
Calories/Pulse display
should be blank. If a “d”
Note: The console’s pulse programs can be used
only with the optional chest pulse sensor.
appears in the display, the
console is in the “demo”
mode. This mode is in-
tended to be used only
when a treadmill is displayed in a store. When the con-
sole is in the demo mode, the power cord can be
plugged in, the key can be removed from the console,
and the displays and indicators on the console will au-
tomatically light in a preset sequence, although the but-
tons on the console will not operate. If a “d” appears
in the Calories/Pulse display when the information
mode is selected, press the Speed
Calories/Pulse display is blank.
M
button so the
To exit the information mode, remove the key from the
console.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
Caution: You must be able to safely lift 45 pounds (20
kg) in order to raise, lower, or move the treadmill.
1. Hold the treadmill in the locations shown at the right. To
decrease the possibility of injury, bend your legs and
keep your back straight. As you raise the treadmill,
make sure to lift with your legs rather than your back.
Raise the treadmill about halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the lock knob to
the left and hold it. Raise the treadmill until all parts of the
treadmill are past the latch pin. Release the lock knob.
Make sure that the lock knob is fully released so the
latch pin is securely holding the catch.
Latch
Pin
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° Fahrenheit.
Lock
Knob
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
latch pin is securely holding the catch.
1. Hold the handrails and place one foot on the base.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To re-
duce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
Base
Front Wheels
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the treadmill with your right hand as shown. Using
your left hand, pull the lock knob to the left and hold it.
Pivot the treadmill down until all parts of the treadmill are
past the pin. Slowly release the lock knob.
Lock
Knob
2. See the drawing at the top of this page. Hold the treadmill
firmly with both hands, and lower the treadmill to the
floor. To decrease the possibility of injury, bend your
legs and keep your back straight.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE-SHOOTING AND MAINTENANCE
Most treadmill problems can be solved by following the instructions below. If further assistance is
needed, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM
SOLUTION
1. The power does not
turn on
a. Make sure that the power cord is plugged into a surge protector, and that the
surge protector is plugged into a properly grounded outlet. (See page 7.) Use only
a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or
less in length.
b. Make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the frame near
the power cord. If the switch protrudes as shown, the
circuit breaker has tripped. To reset the circuit
breaker, wait for five minutes and then press the
switch back in.
Tripped
Reset
d. Check the on/off switch located on the frame near
the power cord. The switch must be in the on posi-
tion.
On
Position
2. The power turns off
during use
a. Check the circuit breaker located on the treadmill frame near the power cord (see
1. c. above). If the circuit breaker has tripped, wait for five minutes and then press
the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console and then reinsert it.
d. Make sure that the on/off switch is in the on position (see 1. d. above).
3. The walking belt
slows when walked
on
a. Make sure that only an appropriate surge protector is used (see 1. a. above).
b. If the walking belt is overtightened, tread-
b
mill performance may decrease and the
walking belt may be permanently dam-
aged. Remove the key and UNPLUG THE
POWER CORD. Using the included allen
wrench, turn both rear roller adjustment
bolts counterclockwise 1/4 of a turn.
3–4”
When the walking belt is properly tight-
ened, you should be able to lift the edges
of the walking belt 3 to 4 inches off the
Rear Roller Adjustment Bolts
walking platform. Be careful to keep the walking belt centered. Plug in the power
cord, insert the key and run the treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
SOLUTION
4. The walking belt is
off-center or slips
when walked on
a. If the walking belt has shifted to the
left, first remove the key and UNPLUG
THE POWER CORD. Using the allen
wrench, turn the left rear roller adjustment
bolt clockwise, and the right bolt counter-
clockwise, 1/4 of a turn each. Be careful
not to overtighten the walking belt. Plug in
the power cord, insert the key and run the
a
treadmill for a few minutes. Repeat until the walking belt is centered.
b. If the walking belt has shifted to the
b
right, first remove the key and UNPLUG
THE POWER CORD. Using the allen
wrench, turn the left rear roller adjustment
bolt counterclockwise, and the right bolt
clockwise, 1/4 of a turn each. Be careful
not to overtighten the walking belt. Plug in
the power cord, insert the key and run the
treadmill for a few minutes. Repeat until the walking belt is centered.
c. If the walking belt slips when walked
c
on, first remove the key and UNPLUG
THE POWER CORD. Using the allen
wrench, turn both rear roller adjustment
bolts clockwise, 1/4 of a turn. When the
walking belt is correctly tightened, you
should be able to lift the edges of the
walking belt 3 to 4 inches off the walking
platform. Be careful to keep the walking belt centered. Plug in the power cord, in-
sert the key and run the treadmill for a few minutes. Repeat until the walking belt
is properly tightened.
5. The displays of the
console do not func-
tion properly
a. Remove the key from the console and UN-
PLUG THE POWER CORD. Next, remove
the screws from the hood and carefully re-
move the hood. Locate the Reed Switch
(26) and the Magnet (85) on the left side of
the Pulley (28). Turn the Pulley until the
Magnet is aligned with the Reed Switch.
Make sure that the gap between the
Magnet and the Reed Switch is about
1/8”. If necessary, loosen the Reed Switch
1/8”
28
2
26
85
Top
View
Screw (2) and move the Reed Switch slightly. Retighten the Screw. Re-attach the
hood, and run the treadmill for a few minutes to check for a correct speed reading.
6. Bubbles form in the
walking belt
a. Due to variations in humidity and temperature, there is a possibility that
bubbles may form in the walking belt. Although the bubbles will disappear with
time, you may unplug the power cord, carefully insert a needle into the bubbles,
and push the air out of the bubbles.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
Aerobic Exercise
EXERCISE INTENSITY
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
HOW TO MEASURE
YOUR HEART RATE
To measure your heart
rate, stop exercising and
place two fingers on
your wrist as shown.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
Take a six-second
heartbeat count, and
Exercise Frequency
multiply the result by ten to find your heart rate. (A six-
second count is used because your heart rate drops
quickly when you stop exercising.) If your heart rate is
too high or too low, adjust the speed or incline of the
treadmill.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired.
Fat Burning
The key to success is to make exercise a regular and
enjoyable part of your everyday life.
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
1
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Hamstrings, back of knees
and back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot to-
ward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back and groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat
3 times for each leg. To cause further stretching of the achilles
tendons, bend your back leg as well. Stretches: Calves, achilles
tendons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps
and hip muscles.
5
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. HRTL09990
R0100A
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key
Key
No. Qty. Description
No. Qty. Description
1
2
3
4
5
6
7
8
9
1
11
6
9
1
2
4
4
2
2
1
2
2
2
1
1
1
1
2
11
4
1
1
1
1
1
1
1
1
2
1
1
1
1
16
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
Motor Hood
Hood Screw
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
2
2
2
2
1
1
2
2
1
1
1
2
2
2
2
1
1
1
1
1
1
1
3
1
8
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
4
5
5
1
2
3
2
2
2
Frame
Rear Wheel
Platform Screw
Platform Washer
Latch Catch
Latch Catch Screw
Isolator
Rear Wheel Bolt
Rear Roller Guard
Rear Wheel Nut
Rear Roller
Right Endcap
Rear Roller Adj. Washer
Rear Roller Adj.Bolt
Left Endcap
Allen Wrench
Walking Platform
Handrail Grip
Handrail Grip Screw
Crossbar Bolt
Crossbar Washer
Lock Knob
Lock Knob Sleeve
Lock Spring
Lock Knob Collar
Pin Clip
Lock Pin
Crossbar
Console Base Screw
Console Base Cover
Cover Screw
Pulse Sensor Cover
Sensor Cover Screw
Key/Clip
Console Base
Book Holder Lens
Console
Belt Guide Screw
Belt Guide
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34*
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Frame Pivot Bolt
Front Roller/Pulley
Incline Motor Spacer
Incline Motor Bolt
Incline Motor Nut
Incline Motor
Front Roller Adj. Nut
Pulse Mounting Plate
Front Roller Adj. Bolt
Side Hood Tab
Hood Tab Screw
Hood Tab Clip
Front Hood Tab
Reed Switch Clip
Motor
2-lb. Hand Weight
Reed Switch
Motor Belt
Pulley/Flywheel/Fan
Motor Tension Bolt
Motor Tension Washer
Motor Star Washer
Motor Tension Nut
Motor Pivot Bolt
Motor/Pulley/Flywheel/Fan
Screw
Choke
Choke Plate
Circuit Breaker
On/Off Switch
Power Cord
Lift Frame
Releasable Tie
Magnet
Cable Tie
8” Power Wire
8” Cable Tie
Jack
10’ IFit.com Wire
Lift Frame Bolt
Plastic Washer
Lift Frame Nut/Wheel Nut
Base Pad
Left Foot Grip
Upright Base Cap
Warning Decal
Wheel Bolt
Power Cord Grommet
Outlet Bracket
Controller
Power Supply
Plastic Stand-Off
Electronics Bracket
Belly Pan
Upright Wire Harness
Right Foot Grip
Walking Belt
Base Wheel
Wheel Insert
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Key
Key
No. Qty. Description
No. Qty. Description
101
102
103
104
105
106
#
#
#
#
#
1
1
1
1
2
2
1
1
1
1
1
1
12” Audio Wire
Large Warning Decal
Upright Base
Shock
Lift Frame Spacer
Endcap Spacer
8” Green Wire, 2 Ring
8” Green Wire, F/Ring
4” Green Wire, F/Ring
20” Blue Wire, 2 F
8” Blue Wire, 2 F
8” Blue Wire, M/F
#
#
#
#
#
#
1
1
1
1
1
1
4” Black Wire, 2 Female
8” Black Wire, M/F
20” White Wire, M/F
8” White Wire, 2 Female
8” Red Wire, M/F
User's Manual
*Includes all parts shown in the box.
#These parts are not illustrated
#
Specifications are subject to change without notice.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). Before calling, please note the following
information:
• The MODEL NUMBER of the product (HRTL09990).
• The NAME of the product (HealthRider® SOFTSTRIDER S300i™ treadmill).
• The SERIAL NUMBER of the product (see the front cover of this manual).
• The KEY NUMBER and DESCRIPTION of the replacement part(s) (see the PART LIST on pages 26 and 27
and the EXPLODED DRAWING attached in the center of this manual).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
WHAT IS COVERED—The entire HealthRider® SOFTSTRIDER S300i™ treadmill (“Product”) is warranted to be free of
all defects in material and workmanship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), extends a lifetime warranty on the frame. The
motor is covered for three years after the date of purchase. The belt and deck are covered for two years after the date
of purchase. All mechanical components are covered for two years after the date of purchase. All electrical components
are covered for two years after the date of purchase. Labor is covered for one year.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or
component, providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized
service provider, or, at our option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, im-
proper assembly or installation, alterations, modifications without our written authorization or by failure on your part to
use, operate, and maintain as set out in your User’s Manual (“Manual”). This warranty does not extend to products used
for commercial or rental purposes or to products used as store display modules.
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the
Product as specified in the Manual; notify our Customer Service Department of any defect within 10 days after discov-
ery of the defect; as instructed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product.
Remember to do the periodic maintenance requirements specified in the Manual to assure proper operation and your
continued satisfaction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-800-999-3756 and tell them
your name and address and the serial number of your Product. They will tell you how to get a part replaced, or if neces-
sary, arrange for service where your Product is located or advise you how to ship the Product for service. Before ship-
ping, always obtain a Return Authorization Number (RA No.) from our Customer Service Department; securely pack
your Product (save the original shipping carton if possible); put the RA No. on the outside of the carton and insure the
product. Include a letter explaining the product or problem and a copy of your proof of purchase if you believe the ser-
vice is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the
use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or
profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature.
Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above lim-
itation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability
or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not
allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty.
This warranty gives you specific legal rights and you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
HealthRider® is a registered trademark of ICON Health & Fitness, Inc.
Part No. 157679 R0100A
Printed in USA © 2000 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|