Hall Research Technologies, Inc
1163 Warner Ave.
Tustin, CA 92780
Phone:
Fax:
(714) 641-6607
(714) 641-6698
User’s Manual
Model MC4-H2
Dual Head KVM Switch
Control 4 Dual Video output PC's from one set of
monitors, keyboard and mouse
April 11, 2006
UMA1091 Rev. 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
MC4-H2 allows two monitors, 1 keyboard, and 1 mouse to control 4 different PC’s or servers. By chaining up to 3 MC4-
H2’s, up to 12 PC’s can be controlled
General
The MC4-H2 switches both video outputs to display
the selected PC’s video outputs at full resolution
using buffered and wideband video circuits. It also
routes the signals from the mouse and keyboard to
the selected pc, while, at the same time, emulating a
keyboard and a mouse for the unselected PCs so that
they can detect and communicate with a “virtual”
mouse and keyboard in order for the PCs to operate
normally.
Upon power up the MC4-H2 will locate and identify
the type of mouse plugged into the mouse port and
initialize that mouse. The same will then be done for
the keyboard.
The power supply included with the MC4-H2 will
power up to 3 MC4-H2 units. Only 1 power supply
is need to power 3 MC4-H2 units.
There are 3 ways the MC4-H2 can switch from one PC to another. The first is through the buttons located on the front
panel of the MC4-H2. The second is through a hot-key sequence from the keyboard and the third is through RS-232
control.
The unit supports 2-button, 3-button, and scroll mice. 4-button mice and above are not supported.
When the MC4-H2 is powered up or reset, the PC that was last selected will be selected by default.
There are two different types of LEDs on the front panel. When the LED labeled PWR is illuminated then the PC
attached to that port is powered on. When the LED labeled SEL is illuminated, then the PC attached to that port is the
selected PC. The selected PC is the PC currently being controlled by then keyboard and mouse.
Supported Systems and Peripherals
•
•
•
•
All PC compatible systems and notebooks
Standard PS/2 and AT Keyboards (Legacy AT keyboards may require connector adapters)
Standard (2-button) and wheel (3-button) (e.g. Microsoft Intellimouse) mice. 4-button mice are not supported.
VGA, XGA, UXGA video resolutions to 1600x1200 at 50 to 85 Hz refresh rate.
Features
•
•
•
•
•
•
•
•
•
•
•
•
Switches two video screens from each PC to user’s console
Extremely reliable operation with proven firmware for no keyboard or mouse lock ups
Video outputs are terminated and buffered with wide bandwidth video amplifiers for sharp and crisp image
Quick and easy switching between PC’s
LED indicators of PC power status and PC selected
Comprehensive PS/2 protocol emulation for keyboard and mouse for all PC’s at all times
Hot-swapping capabilities of the PC’s and the devices
Returns to last selected PC after power off or reset
Small and compact design
Only one cable needed to connect to each PC
Designed and manufactured in the USA
RS-232 Control
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
FIGURE 1 MC4-H2 Connector Functions on Rear Panel
FIGURE 2 CA-100872 Cable for connection to each PC
1. Use the special CA10087-6,or -10 (4-in-1) cable to connect PC A to the MC4-H2. The DB25 connector plugs into
the MC4-H2. The keyboard connector, of the CA10087 cable is either labeled “K” or is purple and plugs into the
keyboard port on PC A. The mouse connector, of the CA10087 cable is either labeled “M” or is green and plugs into
the mouse port of PC A (it is best to turn off all PC’s when you are hooking them to the MC4-H2).
The input cable s are available in two lengths of 6 ft and 10 ft. CA10087-6 or –10 (sold separately)
2. Repeat step 1 for the remaining PC’s. Note: only 4 PC’s may be connected to each MC4-H2 simultaneously. Not all
4 PC ports need to be used for the MC4-H2 to work properly.
3. Connect a mouse to the mouse port of the master MC4-H2. The Master unit is the one with PC # 1 through 4
4. Connect a keyboard to the keyboard port of the master MC4-H2.
5. Plug in the power supply that comes with the MC4-H2 to the unit and connect it to an AC outlet
6. Turn the PC’s on
7. The keyboard and mouse may now be treated as a keyboard and mouse connected directly to the PC that is selected
through the unit.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
The keyboard and mouse will function no differently than if the keyboard and mouse were connected directly to the PC.
Switching
You can use of three ways to switch among the PCs.
The first way is to simply press the button for the desired PC on the front panel of the MC4-H2.
The second way to switch is through a hot-key combination from the keyboard. The hot-key combination is as follows.
Press and release: “Scroll Lock”
Press and release: “Scroll Lock”
Press and release: “01” or “02” or “03” or “04” If more than 1 MC4-H2 are chained together then you can switch to
the other pc’s by pressing their corresponding 2 digit number “05” – “12”
The MC4-H2 will now switch to the PC connected to the port corresponding to the number pressed.
There is a 2 second timeout between each hot key. This means that if the second Scroll Lock is not pressed within 2
seconds of the release of the first Scroll Lock, the sequence will be aborted and will not MC4-H2. The same situation
applies to the number pressed after the release of the second Scroll Lock.
The third way to switch between PC’s is the use of RS-232 serial control. Connect the supplied serial cable (Mini-stereo
to DB9 Female) to the RS232 port on the front of the MC4-H2 and the other end to a PC.
Baud Rate is 4800:
To switch to a PC send the following ASCII commands to the MC4-H2.
Sxx – where “xx” is the 2-digit number of the PC you wish to switch to
Example: S01 – switches to PC #1
By default, when switching, the MC4-H2 will not switch to a port that does not have a powered PC. (i.e. the red PWR led is not
on). This behavior however, can be changed via the Serial control.
The command to allow switching to a non-powered PC is: P1
The command to disallow switching to a non-powered PC is: P0
Setting the address of the MC4-H2
Each MC4-H2 needs to be assigned an address in order to function. The 3 different addresses are the following:
1. Master
2. Slave 1
3. Slave 2
There must be a Master unit for any mouse/keyboard/video communication and switching to take place.
The MC4-H2 unit with the Master address will number the PC's attached to it, 1-4.
The MC4-H2 unit with the Slave 1 address will number the PC's attached to it, 5-8.
The MC4-H2 with the Slave 2 address will number the PC's attached to it, 9-12.
There are 2 ways to set the address of an MC4-H2.
1. Via the front panel push buttons
2. Via Serial control
Front Panel Push Buttons:
Hold down the buttons for port A and port D simultaneously for 3 seconds on the unit where you want to change the address.
When you see the LED's begin to flash this indicates that the address can now be changed for this unit. Press any of the front
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
panel buttons to cycle the address from Master, to Slave 1, to Slave 2 and then back to Master. As the address cycles, you will
see the port number on the front panel LED's changing between the following combinations:
1 2 3 4 or
5 6 7 8 or
9 10 11 12
When you have the proper address selected, press and hold down simultaneously the buttons of port A and port D on the unit.
When the LED's stop blinking, this will indicate that the address has been set. (about 3 seconds)
Serial Control:
You may only change the address of the MC4-H2 unit that you are connected to via a serial cable. Send the following command
to the MC4-H2 to change the address of the box, which you are connected to via the serial cable.
Ax - where "x” is the address you want this unit to have.
The address commands are "M" for Master, "1" for Slave 1, and "2" for Slave 2
Examples:
AM - set this unit's address to Master (Ports 1-4)
A1 - set this unit's address to Slave 1 (Ports 5-8)
When an address is changed, that unit announces it’s new address to any other MC4-H2’s that it is connected to via the chain
cable. If any unit already has this address, it will loose it’s address to the unit that just changed addresses. Here is an example.
Let’s say you have two MC4-H2’s. Call them Unit A and Unit B. Unit A is set as the Master and Unit B is set as the Slave 1. If
you were to change the address of Unit B to the master, Unit A will have to give up it’s address since Unit B has now taken the
Master address. Unit A will now not have an address and the LED’s will be blinking “00”. Give Unit A an address by following
the front panel method or the serial method.
Note:
If a unit has no address, the LED’s are flashing “00”, you will still need to hold down the buttons on port A and
port D for 3 seconds and the press any front panel button to select a new address and then continue with the
Front Panel address changing method.
Stacking (Daisy-Chaining) of Multiple MC4-H2 Units
In order to connect two or more units to expand the number of PC’s that you control, you need to order a Daisy-Chain Cable Set.
Connect the OUT of the Slave #1 to the IN of the Master. If you have a 2nd slave connect the OUT of it to the IN of Slave #1. The
Power Supply connected to the master unit will power up the Slave Units through the expansion port. However there is no
damage if you connect supplies to the slaves and in fact it is recommended when you have 3 units.
FIGURE 3 Stacking of MC4-H2 Units
Hot Swapping Mice and Keyboards
Hot swapping is not recommended but may be successfully performed. You may unplug the mouse and/or the keyboard
while the MC4-H2 is powered up and PC’s are connected and powered on. You may then plug in the same
keyboard/mouse or a different keyboard/mouse and the MC4-H2 will recognize the new keyboard/mouse.
Hot Swapping PC’s
You may hot swap a PC while the MC4-H2 is powered up only after that PC has been turned off. After the PC has been
turned off, unplug the keyboard, mouse, and video connectors of the CA10087 (4-in-1) cable then plug them into the PC
you wish to insert into the MC4-H2 setup. Then power on the new PC.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Dimensions
Width X Height X Depth
19 X 1-3/4 X 5-1/4 in Single Rack Unit (1RU) construction
Video
Max Resolution 1600 X 1200
Coupling
Video Level
Video Gain
Bandwidth
Drive
DC
0.7 V p-p
1; double-terminated
250 MHz
0 to 25 ft. on User Console
Keyboard
Connector:
Type
Mini Din 6-pin Female
All AT and Windows® compatible keyboards
All modes supported by the operating system
Mode
Communication Bi-directional
Mouse
Connector
Mini Din 6-pin Female
Mouse Type
Any PS2 mouse or pointing device
Federal Communications Commission (FCC) Statement __________
This equipment generates, uses and radiates radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. This
equipment has been designed to comply with the limits for a Class A computing device, pursuant to Part
15 of the FCC rules. Harmful interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference, in which case the user, at his own expense,
will be required to take whatever measures are necessary to correct the interference.
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
© Copyright 2006. Hall Research Technologies, Inc.
All rights reserved.
.
.
.
.
.
.
.
.
Hall Research Technologies, Inc.
1163 Warner Ave.
Tustin, CA 92780
Phone: (714) 641-6607 Fax:(714) 641-6698
Download from Www.Somanuals.com. All Manuals Search And Download.
|