INSTALL INSTRUCTIONS KK-K9-F14-K-PT
K9/PRISONER TRANSPORTATION SYSTEM
2003-2009 FORD EXPEDITION
HARDWARE:
QTY: DESCRIPTION:
PART #:
28
8
64
6
¼-20 x ½” Stainless carriage bolt
¼-20 x ¾” Stainless carriage bolt
¼-20 flanged serrated nut
¼-20 x ¾” Hex head cap screw
¼” x 1 ½” Hex head lag screw
#12 x ¾” Stainless sheet metal screw
#10 x ¾” Stainless sheet metal screw
#10 x ½” Stainless sheet metal screw
10-32 x ¾” Stainless machine screw
#10 x ¾” Sheet metal screw
GSM32022
GSM32024
GSM30023
GSM33001
GSM33062
GSM34177
GSM34170
GSM34169
GSM34098
GSM33195
PRM97343
KNM01029-SUV
GSM33150
KNM001220
6
36
24
12
10
6
1
1
10
1
Tube silver caulk
46” x 45 ½” Rubber Floor mat
#10 x ½” Flat head sheet metal screw
¼” Lexan shield/PT front partition
Always!
¾ Read all instructions before installing any Havis-Shields Equipment Corp products.
¾ Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
¾ Use hardware provided with install kit
¾ For product support, visit the Install Instructions Section of our website at
1-800-524-9900.
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove plastic trim piece. Metal
clips hold on trim
Remove window/lock switch
assembly from door
View of Expedition door panel
Remove hex head screws holding
lower section of door panel
Remove trim piece covering torx
screws under door panel armrest
and remove screws
Remove plastic door panel
Remove window switch and
reconnect. Wire tie switch in safe
location.
Remove speaker from door panel.
Remove screws and unplug
Recommended location for switch
KK-K9-F14-K-PT_INST_11-08
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2006-2008 FORD EXPEDITION DOOR
Remove bolt
1. Remove the specified bolt and cut on
the line shown left.
2. The upper portion of the cut piece
will remain off.
3. Save for vehicle re-sale.
Cut on this line
Back seat configuration for
Ford Expedition
Remove seat bolts from center
and driver side Back seats.
Remove rear plastic storage
compartment if included.
Attach the rear floor mount bracket
to the K9 housing with ¼ x ½ bolts.
Slide K9 section of assembly
through back hatch of vehicle. Be
Leave passenger-side rear seat
careful not to rip headliner or
KK-K9-F14-K-PT_INST_11-08
4
scratch trim panels.
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Mounting plate straddles a ridge in the floor. When bolts
are tightened the plate will form to the floor.
7 ¾”
Sub-assemble mounting leg to
mounting plate using ¼” x ¾”
carriage bolts and serrated nuts. Set
mounting leg assembly to 7 ¾”
Attach assembly to vehicle
using OEM seat hardware and
nutcerts in vehicle
Attach assembly to K9 floor
using ¼” x ¾” carriage bolts
and serrated nuts
View of mounting foot from
Adjust mounting foot until K9
unit is level within the vehicle
floor of K9
Single mounting
hole
View of mounting feet from
drivers’ compartment
Place tunnel assembly as shown
above
Attach tunnel to K9 assembly using ¼” x
¾” and ¼” x ½” carriage bolts and
serrated nuts
Note: ¾” bolts are used where (3) layer
thicknesses of aluminum bolt together
KK-K9-F14-K-PT_INST_11-08
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Place front partition filler panel
into vehicle as shown above
View of assembly at this time
Position front partition as
shown and attach to K9
housing assembly
Remove “B” pillar upper trim
panel. Remove seat belt bolt
Position ¼” lexan shield
Using holes in partition mark and
drill shield Attach using ¼” x ¾”
carriage bolt and serrated nut
Remove bolt located behind
plastic trim
Remove trim panel to access
bolts for grab handle.
Remove grab handle
KK-K9-F14-K-PT_INST_11-08
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach “B” pillar mounting
bracket to front partition using
¼” x ¾” carriage bolts and nuts
Install “B” pillar mounting
bracket using bolts that hold
grab handle. (Re-installing the
grab handle is optional)
Grab handle removed
Install ceiling filler panel to
passenger side of K9 housing using
¼” x ¾” carriage bolts and nuts
Attach ceiling filler panel to
front partition using ¼” x ¾”
carriage bolt and nut
View of ceiling filler
from rear of vehicle
Location on inside of K9 assembly
where rear partition will bolt to using
¼” x ¾” carriage bolts and nuts
View of ceiling filler from
passenger side rear door
Position rear partition through
vehicles rear hatch
KK-K9-F14-K-PT_INST_11-08
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Location where ceiling filler bolts
to rear partition
Pre-drill holes using 3/16” drill bit
and attach using ¼”x 1” Lag bolts
Attach rear partition to floor of
vehicle.
Attach front partition to vehicle using
6” L-mounting bracket. Bolt bracket
to partition using ¼” x ¾” carriage
bolts and nuts. Bolt “L” mounting
bracket to vehicle using ¼” x 1” Lag
bolts. Pre-drill w/ 3/16” hole
Position floor filler panel to K9
housing, mark holes and pre-drill
K9 housing using 1/8” drill bit
Attach to K9 housing using #10 x
¾” sheet metal screws.
Top Inner Screw
Upper
Aluminum
Bracket
Center door panels so edges do not hang
over. Attach to door with #10 x ½”
stainless sheet metal screws.
Note: Window guards have holes around
perimeter for permanent mounting.
These holes are not used with hinge style
window kits! They also come flat in
shipping.
Hold window guard with pre-assembled
hinge and upper bracket onto window frame.
Make sure guard is centered on window.
Attach hinge to lower door panel with #10 x
½” stainless sheet metal screws. Mark upper
aluminum bracket location on window frame
and remove from window guard. Attach
The window guard must be pre-
bent so it fits tight against the
contour of the door window
frame. The aluminum guard can
easily be formed at workbench.
upper aluminum bracket onto window frame
8
with #10 x ½” flat head sheet metal screws.
Download from Www.Somanuals.com. All Manuals Search And Download.
Hinge up window
guard and reattach to
bracket with 10-32 x
½” Stainless machine
screws and #10 Flat
washers.
NOTE: Door panel
fillers are provided for
the Expedition EL.
This is not used for the
standard length
Standard
door panel
Expedition.
K9 / PT unit installation complete.
Shown with emergency sliding door open between K9 and Prisoner compartment.
Sheet metal seams and gaps need to be carefully
SILICONED at floor area. Allow silicone to dry overnight
before placing in rubber floor mat
KK-K9-F14-K-PT_INST_11-08
9
Download from Www.Somanuals.com. All Manuals Search And Download.
|