Adult Collectible
89832/87991 Asst.
WARNING!
To prevent risk of electric shock or serious injury, never disassemble the
lightsaber.
®
™
M A C E W I N D U
™
• DO NOT attempt to perform any repairs yourself. There are no consumer
repairable parts inside.
C O L L E C T I B L E
F O R C E F X L I G H T S A B E R
• Never use to strike others. This product is not intended for striking
people, animals or objects. This product is not covered by warranty for
damage caused by striking against hard objects.
1
• Never run with the lightsaber. Never use the lightsaber in total darkness.
• Always check the area around you before swinging the lightsaber to ensure
you do not injure anyone or cause damage.
• Turn off the lightsaber when not in use. Never leave the lightsaber on when
unattended.
3
• To prevent risk of electric shock or serious injury, never immerse the
lightsaber in water or allow the lightsaber to become wet. Use only a soft,
dry cloth to clean.
2
4
• If the blade of the lightsaber becomes cracked or damaged, stop using the
lightsaber immediately.
BATTERY INSTALLATION
1. Make sure the lightsaber is OFF.
2. Unscrew pommel (end cap) counter-clockwise to expose the battery pack.
3. Completely remove the battery pack from the hilt (handle).
4. Using a Phillips/crosshead screwdriver (not included), loosen screw in
battery pack sleeve (screw will remain attached to sleeve). Slide sleeve off
battery pack.
5
6
5. Insert 3 x 1.5V “AAA” or LR03 size alkaline batteries in the battery pack.
Make sure the batteries are correctly oriented; refer to the + and – markings
as a guide.
6. To re-insert the battery pack, slide sleeve back onto pack, and tighten
screw. Align the yellow arrow on the pack with the yellow triangle inside the
hilt (handle). Slide it in until it stops. DO NOT FORCE! Replace pommel (end
cap) by screwing it on clockwise.
1.5VAAA/LR03 size
x3
BATTERIES REQUIRED
Requires 3 x 1.5V “AAA” or LR03 size
alkaline batteries (not included).
P/N 6896930000
Product and colors may vary.
© 2009 Lucasfilm Ltd. & ® or TM where indicated. All rights reserved.
®* and/or ™* & © 2008 Hasbro. All Rights Reserved.
TM & ® denote U.S. trademarks.
*
*
PLEASE RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
FREQUENTLY ASKED QUESTIONS
OPERATING INSTRUCTIONS
IMPORTANT:BATTERY INFORMATION
Q: Is the Force FX Lightsaber a licensed collectible?
A: Yes. The Force FX Lightsaber is a licensed collectible approved and endorsed by
Lucasfilm Ltd. As a collectible, the Force FX Lightsaber is not suitable for children.
On/Off
Locate the ON/OFF switch on the
control panel as shown in the
diagram. To turn the lightsaber ON,
slide the switch forward, away from
you. To turn the lightsaber OFF, slide
the switch backward, toward you.
CAUTION:
1. As with all small batteries, the batteries used with this product should be
kept away from small children who still put things in their mouths. If they
are swallowed, promptly see a doctor and have the doctor phone (202)
625-3333 collect. If you reside outside the United States, have the doctor
call your local poison control center.
Q: Is the Force FX Lightsaber a limited edition prop replica?
A: No. Although the design of the Force FX Lightsaber is faithful to the look of the movie
prop, it is not an exact replica. The hilt of the Force FX Lightsaber was made slightly
larger than the actual movie prop in order to accommodate the electronics that control
the light and sound effects. The Force FX Lightsaber collectibles are not limited to a pre-
determined edition size; therefore, they are not classified as limited edition replicas.
2. Always follow the instructions carefully. Use only batteries specified and be
sure to insert them correctly by matching the + and – polarity markings.
3. Do not mix old batteries and new batteries or standard (carbon-zinc)
with alkaline batteries.
4. Remove exhausted or dead batteries from the product.
5. Remove batteries if product is not to be played with for a long time.
6. Do not short-circuit the supply terminals.
DISPLAY STAND
Q: What is the blade on the Force FX Lightsaber made of?
A: The Force FX Lightsaber features a permanently attached polycarbonate blade. Once
activated, the blade glows brightly and the replica plays back digitally recorded sound
effects taken directly from the film.
Assemble stand as shown.
Place lightsaber on stand as shown.
7. Should this product cause, or be affected by, local electrical interference,
move it away from other electrical equipment. Reset (switching off and back on
again or removing and re-inserting batteries) if necessary.
8. RECHARGEABLE BATTERIES: Do not mix these with any other types
of batteries. Always remove from the product before recharging. Recharge
batteries under adult supervision. DO NOT RECHARGE OTHER TYPES
OF BATTERIES.
Q: Is the blade on the Force FX Lightsaber removable?
A: No, the blade is not removable or retractable.
Q: How do the light and sound effects work in the Force FX Lightsaber?
A: The Force FX Lightsaber incorporates motion sensors, which sense both the motion
of the blade as well as when it comes in contact with something. An on-board, multi-
channel chip is programmed with digital sound effects originally created for the movie by
Skywalker Sound. The Force FX Lightsaber replicates the following sound effects:
• Power-up
• Idle hum
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
• Swing (with pitch change)
• Clash
• Power-down
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Q: How long should the light in the Force FX Lightsaber last?
A: It should run for several hours on a fresh set of batteries. The electronics, if cared for
properly, should last for several thousand hours of use. Replace the batteries whenever
the performance begins to change, such as reduced brightness or volume.
Q: Can I use my Force FX Lightsaber for dueling?
A: No. This product should not be used to strike other people or animals. Although
the blade is very durable, it should never be used for fighting or dueling. The Force FX
Lightsaber was produced to be a collectible.
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Consult the dealer or an experienced radio/TV technician for
help.
Q: Sometimes I see a dark spot in the middle of the blade. Is there something wrong with
the lightsaber?
A: No. The dark area is actually a result of the design. All the Force FX Lightsabers are
handmade and as a result, this slightly dark area at the middle of the blade is normal. This
does not affect the performance of the lightsaber in any way.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
|